1. ResistorsResistors are the most commonly used component in electronics and their purpose is to create specified values of current and voltage in a circuit. A number of different resistors are shown in the photos. (The resistors are on millimeter paper, with 1cm spacing togive some idea ofthe dimensions). Photo 1.1ashowssome low-powerresistors,whilephoto1.1b showssome higher-powerresistors.Resistors with power dissipation below 5 watt (most commonly used types) are cylindrical in shape, with a wire protruding from each end for connecting to a circuit (photo 1.1-a).Resistors with power dissipation above 5 watt are shown below (photo 1.1-b).

Fig. 1.1a: Some low-power resistorsFig.1.1b: High-power resistors and rheostats

The symbol for a resistor is shown in the following diagram(upper: American symbol, lower: European symbol.)

Fig. 1.2a: Resistor symbolsThe unit for measuring resistance is theOHM. (the Greek letter - called Omega). Higher resistance values are represented by "k" (kilo-ohms) and M (meg ohms).For example, 120 000 is represented as 120k, while 1 200 000 is represented as 1M2. The dot is generally omitted as it can easily be lost in the printing process.In some circuit diagrams, a value such as 8 or 120 represents a resistance in ohms. Another common practice is to use the letter E for resistance in ohms. The letter R can also be used. For example, 120E (120R) stands for 120, 1E2 stands for 1R2 etc.1.1 Resistor MarkingsResistance value is marked on the resistor body. Most resistors have 4 bands. The first two bands provide the numbers for the resistance and the third band provides the number of zeros. The fourth band indicates the tolerance. Tolerance values of5%, 2%, and 1% are most commonly available.

The following table shows the colors used to identify resistor values:COLORDIGITMULTIPLIERTOLERANCETC

Silverx 0.0110%

Goldx 0.15%

Black0x 1

Brown1x 101%100*10-6/K

Red2x 1002%50*10-6/K

Orange3x 1 k15*10-6/K

Yellow4x 10 k25*10-6/K

Green5x 100 k0.5%

Blue6x 1 M0.25%10*10-6/K

Violet7x 10 M0.1%5*10-6/K

Grey8x 100 M

White9x 1 G1*10-6/K

** TC - Temp. Coefficient, only for SMD devices

Fig. 1.2: b. Four-band resistor, c. Five-band resistor, d. Cylindrical SMD resistor, e. Flat SMD resistor The following shows all resistors from 0R1 (one tenth of an ohm) to 22M:

NOTES:The resistors above are "common value" 5% types.The fourth band is called the "tolerance" band. Gold = 5%(tolerance band Silver =10% but no modern resistors are 10%!!)"common resistors" have values 10 ohms to 22M.

RESISTORS LESS THAN 10 OHMSWhen thethirdband is gold, it indicates the value of the "colors" must be divided by 10.Gold = "divide by 10" to get values 1R0 to 8R2See 1st Column above for examples.

When thethirdband is silver, it indicates the value of the "colors" must be divided by 100.(Remember: more letters in the word "silver" thus the divisor is "larger.")Silver = "divide by 100" to get values 0R1 (one tenth of an ohm)to 0R82e.g: 0R1 = 0.1 ohm 0R22 = point 22 ohmsSee 4th Column above for examples.

The letters "R, k and M" take the place of a decimal point. The letter "E" is also used to indicate the word "ohm."e.g: 1R0 = 1 ohm 2R2 = 2 point 2 ohms 22R= 22 ohms2k2 = 2,200 ohms 100k= 100,000 ohms2M2 = 2,200,000 ohmsCommon resistors have 4 bands. These are shown above. First two bands indicate the first two digits of the resistance, third band is the multiplier (number of zeros that are to be added to the number derived from first two bands) and fourth represents the tolerance.Marking the resistance with five bands is used for resistors with tolerance of 2%, 1% and other high-accuracy resistors. First three bands determine the first three digits, fourth is the multiplier and fifth represents the tolerance.For SMD (Surface Mounted Device) the available space on the resistor is very small. 5% resistors use a 3 digit code, while 1% resistors use a 4 digit code.Some SMD resistors are made in the shape of small cylinder while the most common type is flat. Cylindrical SMD resistors are marked with six bands - the first five are "read" as with common five-band resistors, while the sixth band determines the Temperature Coefficient (TC), which gives us a value of resistance change upon 1-degree temperature change.The resistance of flat SMD resistors is marked with digits printed on their upper side. First two digits are the resistance value, while the third digit represents the number of zeros. For example, the printed number 683 stands for 68000, that is 68kIt is self-obvious that there is mass production of all types of resistors. Most commonly used are the resistors of the E12 series, and have a tolerance value of 5%. Common values for the first two digits are: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68 and 82.The E24 series includes all the values above, as well as: 11, 13, 16, 20, 24, 30, 36, 43, 51, 62, 75 and 91. What do these numbers mean? It means that resistors with values for digits "39" are: 0.39,3.9,39,390,3.9k39k, etc are manufactured. (0R39,3R9,39R,390R,3k939k)For some electrical circuits, the resistor tolerance is not important and it is not specified. In that case, resistors with 5% tolerance can be used. However, devices which require resistors to have a certain amount of accuracy, need a specified tolerance.1.2 ResistorDissipationIf the flow of current through a resistor increases, it heats up, and if the temperature exceeds a certain critical value, it can be damaged. The wattage rating of a resistor is the power it can dissipate over a long period of time.Wattage rating is not identified on small resistors. The following diagrams show the size and wattage rating:

Fig. 1.3: Resistor dimensionsMost commonly used resistors in electronic circuits have a wattage rating of 1/2W or 1/4W. There are smaller resistors (1/8W and 1/16W) and higher (1W, 2W, 5W, etc).In place of a single resistor with specified dissipation, another one with the same resistance and higher rating may be used, but its larger dimensions increase the space taken on a printed circuit board as well as the added cost.Power(in watts) can be calculated according to one of the following formulae, where U is the symbol for Voltage across the resistor (and is in Volts), I is the symbol for Current in Amps and R is the resistance in ohms:

For example, if the voltage across an 820resistor is 12V, the wattage dissipated by the resistors is:

A 1/4W resistor can be used.In many cases, it is not easy to determine the current or voltage across a resistor. In this case the wattage dissipated by the resistor is determined for the "worst" case. We should assume the highest possible voltage across a resistor, i.e. the full voltage of the power supply (battery, etc).If we mark this voltage asVB, the highest dissipation is:

For example, ifVB=9V, the dissipation of a 220resistor is:

A0.5W or higher wattage resistor should be used1.3 Nonlinear resistorsResistance values detailed above are a constant and do not change if the voltage or current-flow alters. But there are circuits that require resistors to change value with a change in temperate or light. This function may not be linear, hence the nameNONLINEAR RESISTORS.There are several types of nonlinear resistors, but the most commonly used include :NTCresistors (figure a) (Negative Temperature Co-efficient) - their resistance lowers with temperature rise.PTCresistors (figure b) (Positive Temperature Co-efficient) - their resistance increases with the temperature rise.LDRresistors (figure c) (Light Dependent Resistors) - their resistance lowers with the increase in light.VDRresistors (Voltage dependent Resistors) - their resistance critically lowers as the voltage exceeds a certain value. Symbols representing these resistors are shown below.

Fig. 1.4: Nonlinear resistors - a. NTC, b. PTC, c. LDRIn amateur conditions where nonlinear resistor may not be available, it can be replaced with other components. For example,NTCresistor may be replaced with a transistor with a trimmer potentiometer, for adjusting the required resistance value. Automobile lightmay play the role ofPTCresistor, whileLDRresistor could be replaced with an open transistor. As an example, figure on the right shows the 2N3055, with its upper part removed, so that light may fall upon the crystal inside.

1.4 Practical examples with resistorsFigure 1.5 shows two practical examples with nonlinear and regular resistors as trimmer potentiometers, elements which will be covered in the following chapter.

Fig. 1.5a: RC amplifierFigure 1.5a represents an RC voltage amplifier, that can be used for amplifying low-frequency, low-amplitude audio signals, such as microphone signals. The signal to be amplified is brought between node 1(amplifier input)and gnd, while the resulting amplified signal appears between node 2(amplifier output)and gnd. To get the optimal performance (high amplification, low distortion, low noise, etc) , it is necessary to "set" the transistor's operating point. Details on the operating point will be provided in chapter 4; for now, let's just say that DC voltage between node C and gnd should be approximately one half of battery (power supply) voltage. Since battery voltage equals 6V, voltage in node C should be set to 3V. Adjustments are made via resistor R1.Connect a voltmeter between node C and gnd. If voltage exceeds 3V, replace the resistor R1=1.2Mwith a smaller resistor, say R1=1M. If voltage still exceeds 3V, keep lowering the resistance until it reaches approximately 3V. If the voltage at node C is originally lower than 3V, increase the resistance of R1.The degree of amplification of the stage depends on R2 resistance:higher resistance - higher amplification,lower resistance - lower amplification. If the value of R2 is changed, the voltage at node C should be checked and adjusted (via R1).Resistor R3 and 100F capacitor form a filter to prevent feedback from occurring. This feedback is called "Motor-boating" as it sounds like the noise from a motor-boat. This noise is only produced when more than one stage is employed.As more stages are added to a circuit, the chance of feedback, in the form of instability or motor-boating, will occur.This noise appears at the output of the amplifier, even when no signal is being delivered to the amplifier.The instability is produced in the following manner:Even though no signal is being delivered to the input, the output stage produces a very small background noise called "hiss. This comes from current flowing through the transistors and other components.This puts a very small waveform on the power rails. This waveform is passed to the input of the first transistor and thus we have produced a loop for "noise-generation." The speed with which the signal can pass around the circuit determines the frequency of the instability. By adding a resistor and electrolytic to each stage, a low-frequency filter is produced and this "kills" or reduces the amplitude of the offending signal. The value of R3 can be increased if needed.

Practical examples with resistors will be covered in the following chapters as almost all circuits require resistors.

Fig. 1.5b:Sound indicator of changes in temperature or the amount of lightA practical use for nonlinear resistors is illustrated on a simple alarm device shown in figure 1.5b. Without trimmer TP and nonlinear NTC resistor it is an audio oscillator. Frequency of the sound can be calculated according to the following formula:

In our case, R=47kand C=47nF, and the frequency equals:

When, according to the figure, trim pot and NTC resistor are added, oscillator frequency increases. If the trim pot is set to minimum resistance, the oscillator stops. At the desired temperature, the resistance of the trim pot should be increased until the oscillator starts working again. For example, if these settings were made at 2C, the oscillator remains frozen at higher temperatures, as the NTC resistor's resistance is lower than nominal. If the temperature falls the resistance increases and at 2C the oscillator is activated.If an NTC resistor is installed in a car, close to the road surface, the oscillator can warn driver if the road is covered with ice. Naturally, the resistor and two copper wires connecting it to the circuit should be protected from dirt and water.If, instead of an NTC resistor, a PTC resistor is used, the oscillator will be activated when the temperature rises above a certain designated value. For example, a PTC resistor could be used for indicating the state of a refrigerator: set the oscillator to work at temperatures above 6C via trimmer TP, and the circuit will signal if anything is wrong with the fridge.Instead of an NTC, we could use an LDR resistor - the oscillator would be blocked as long as a certain amount of light is present. In this way, we could make a simple alarm system for rooms where a light must be always on.The LDR can be coupled with resistor R. In that case, the oscillator works when the light is present, otherwise it is blocked. This could be an interesting alarm clock for huntsmen and fishermen who would like to get up at the crack of dawn, but only if the weather is clear. For the desired moment in the early morning, the trim pot should be set to the uppermost position. Then, the resistance should be carefully reduced, until the oscillator starts. During the night the oscillator will be blocked, since there is no light and LDR resistance is very high. As the amount of light increases in the morning, the resistance of the LDR drops and the oscillator is activated when the LDR is illuminated with the required amount of light.The trim pot from the figure 1.5b is used for fine adjustments. Thus, TP from figure 1.5b can be used for setting the oscillator to activate under different conditions (higher or lower temperature or amount of light).1.5 PotentiometersPotentiometers (also calledpots) are variable resistors, used as voltage or current regulators in electronic circuits. By means of construction, they can be divided into 2 groups: coated and wire-wound.With coated potentiometers, (figure 1.6a), insulator body is coated with a resistive material. There is a conductive slider moving across the resistive layer, increasing the resistance between slider and one end of pot, while decreasing the resistance between slider and the other end of pot.

Fig. 1.6a: Coated potentiometerWire-woundpotentiometers are made of conductor wire coiled around insulator body. There is a slider moving across the wire, increasing the resistance between slider and one end of pot, while decreasing the resistance between slider and the other end of pot.Coated pots are much more common. With these, resistance can be linear, logarithmic, inverse-logarithmic or other, depending upon the angle or position of the slider. Most common are linear and logarithmic potentiometers, and the most common applications are radio-receivers, audio amplifiers, and similar devices where pots are used for adjusting the volume, tone, balance, etc.Wire-wound potentiometers are used in devices which require more accuracy in control. They feature higher dissipation than coated pots, and are therefore in high current circuits.Potentiometer resistance is commonly of E6 series, including the values: 1, 2.2 and 4.7. Standard tolerance values include 30%, 20%, 10% (and 5% for wire-wound pots).Potentiometers come in many different shapes and sizes, with wattage ranging from 1/4W (coated pots for volume control in amps, etc) to tens of watts (for regulating high currents). Severaldifferent pots are shown in the photo 1.6b, along with the symbol for a potentiometer.

Fig. 1.6b: PotentiometersThe upper model represents a stereo potentiometer. These are actually two pots in one casing, with sliders mounted on shared axis, so they move simultaneously. These are used in stereophonic amps for simultaneous regulation of both left and right channels, etc.Lower left is the so called slider potentiometer.Lower right is a wire-wound pot with a wattage of 20W, commonly used as rheostat (for regulating current while charging a battery etc).For circuits that demand very accurate voltage and current values,trimmer potentiometers(or justtrim pots) are used. These are small potentiometers with a slider that is adjusted via a screwdriver.Trim pots also come in many different shapes and sizes, with wattage ranging from 0.1W to 0.5W. Image 1.7 shows several different trim pots,along with the symbol.

Fig. 1.7: Trim potsResistance adjustments are made via a screwdriver. Exception is the trim pot on the lower right, which can be adjusted via a plastic shaft. Particularly fine adjusting can be achieved with the trim pot in the plastic rectangular casing (lower middle). Its slider is moved via a screw, so that several full turns isrequired to move the slider from one end to the other.1.6 Practical examples with potentiometersAs previously stated, potentiometers are most commonly used in amps, radio and TV receivers, cassette players and similar devices. They are used for adjusting volume, tone, balance, etc.As an example, we will analyze the common circuit for tone regulation in an audio amp. It contains two pots and is shown in the figure 1.8a.

Fig. 1.8 Tone regulation circuit: a. Electrical scheme, b. Function of amplificationPotentiometer marked BASS regulates low frequency amplification. When the slider is in the lowest position, amplification of very low frequency signals (tens of Hz) is about ten times greater than the amplification of mid frequency signals (~kHz). If slider is in the uppermost position, amplification of very low frequency signals is about ten times lower than the amplification of mid frequency signals. Low frequency boost is useful when listening to music with a beat (disco, jazz, R&B...), while Low Frequency amplification should be reduced when listening to speech or classical music.Similarly, potentiometer marked TREBLE regulates high frequency amplification. High frequency boost is useful when music consists of high-pitched tones such as chimes, while for example High Frequency amplification should be reduced when listening to an old record to reduce the background noise.Diagram 1.8b shows the function of amplification depending upon the signal frequency. If both sliders are in their uppermost position, the result is shown with curve 1-2. If both are in mid position function is described with line 3-4, and with both sliders in the lowest position, the result is shown with curve 5-6. Setting the pair of sliders to any other possible results in curves between curves 1-2 and 5-6.Potentiometers BASS and TREBLE are coated by construction and linear by resistance.The third pot in the diagram is a volume control. It is coated and logarithmic by resistance (hence the marklog)

2. CapacitorsCapacitors are common components of electronic circuits, used almost as frequently as resistors. The basic difference between the two is the fact that capacitor resistance (called reactance) depends on the frequency of the signal passing through the item. The symbol for reactance is Xcand it can be calculated using the following formula:

frepresenting the frequency in Hz andCrepresenting the capacitance in Farads.For example, 5nF-capacitor'sreactance atf=125kHz equals:

while, atf=1.25MHz, it equals:

A capacitor has an infinitely high reactance for direct current, becausef=0.Capacitors are used in circuits for many different purposes. They are common components of filters, oscillators,power supplies, amplifiers,etc.The basic characteristic ofacapacitor is its capacity - the higher the capacity, the higher is the amount of electricity it can hold. Capacity is measured in Farads (F). As one Farad represents fairly high capacity, smaller values such as microfarad (F), nanofarad (nF) and picofarad (pF) are commonly used. As a reminder, relations between units are:1F=106F=109nF=1012pF,that is 1F=1000nF and 1nF=1000pF. It is essential to remember this notation, as same values may be marked differently in some circuits. For example, 1500pF is the same as 1.5nF, 100nF is 0.1F.A simpler notation system is used as with resistors. If the mark on the capacitor is 120 the value is 120pF, 1n2 stands for 1.2nF, n22 stands for 0.22nF, while .1 (or .1u) stands for 0.1F.Capacitors come in various shapes and sizes, depending on their capacity, working voltage, type of insulation, temperature coefficient and other factors. All capacitors can divided in two groups: those with changeable capacity values and those with fixed capacity values. These will covered in the following chapters.2.1 Block-capacitorsCapacitorswith fixed values (the so calledblock-capacitors) consist of two thin metal plates (these are called "electrodes" or sometimes called the "foil"), separated by a thin insulating material such as plastic. The most commonly used material for the "plates" is aluminum, while the common materials used for insulator include paper, ceramic, mica, etc after which the capacitors get named. A number of different block-capacitors are shown in the photo below. A symbol for a capacitor is in the upper right corner of the image.

Fig. 2.1: Block capacitorsMost of the capacitors, block-capacitors included, are non-polarized components, meaning that their leads are equivalent in respect of the way the capacitor can be placed in a circuit. Electrolytic capacitors represent the exception as their polarity is important. This will be covered in the following chapters.2.1.1 Marking the block-capacitorsCommonly, capacitors are marked by a set of numbers representing the capacity. Beside this value is another number representing the maximal working voltage, and sometimes tolerance, temperature coefficient and some other values are printed as well. But on the smallest capacitors (such as surface-mount) there are no markings at all and you must not remove them from their protective strips until they are needed. The size of a capacitor is never an indication of its value as the dielectric and the number of layers or "plates" can vary from manufacturer to manufacturer. The value of a capacitor on a circuit diagram, marked as 4n7/40V, means the capacitor is 4,700pF and its maximal working voltage is 40v. Any other 4n7 capacitor with higher maximal working voltage can be used, but they are larger and more expensive.Sometimes, capacitors are identified with colors, similar to the 4-band system used for resistors (figure 2.2). The first two colors (A and B) represent the first two digits, third color (C) is the multiplier, fourth color (D) is the tolerance, and the fifth color (E) is the working voltage.With disk-ceramic capacitors (figure 2.2b) and tubular capacitors (figure 2.2c) working voltage is not specified, because these are used in circuits with low DC voltage. If a tubular capacitor has five color bands on it, the first color represents the temperature coefficient, while the other four specify the capacity in the previously described way.

COLORDIGITMULTIPLIERTOLERANCEVOLTAGE

Black0x 1 pF20%

Brown1x 10 pF1%

Red2x 100 pF2%250V

Orange3x 1 nF2.5%

Yellow4x 10 nF400V

Green5x 100 nF5%

Blue6x 1F

Violet7x 10F

Grey8x 100F

White9x 1000F10%

Fig. 2.2: Marking the capacity using colorsThe figure 2.3 shows how the capacity of miniature tantalum electrolytic capacitors are marked by colors. The first two colors represent the first two digits and have the same values as with resistors. The third color represents the multiplier, to get the capacity expressed in F. The fourth color represents the maximal working voltage.

COLORDIGITMULTIPLIERVOLTAGE

Black0x 1F10V

Brown1x 10F

Red2x 100F

Orange3

Yellow46.3V

Green516V

Blue620V

Violet7

Grey8x .01F25V

White9x .1F3V

Pink35V

Fig. 2.3: Marking the tantalum electrolytic capacitorsOne important note on the working voltage: The voltage across a capacitor must not exceed the maximal working voltage as the capacitor may get destroyed. In the case when the voltage is unknown, the "worst" case should be considered. There is the possibility that, due to malfunction of some other component, the voltage on capacitor equals the power supply voltage. If, for example, the supply is 12V, the maximal working voltage for the capacitor should be higher than 12V.2.1 Electrolytic capacitorsElectrolytic capacitors represent the special type of capacitors with fixed capacity value. Thanks to special construction, they can have exceptionally high capacity, ranging from one to several thousand F. They are most frequently used in circuits for filtering, however they also have other purposes.Electrolytic capacitors are polarized components, meaning they have positive and negative leads, which is very important when connecting it to a circuit. The positive lead or pin has to be connected to the point with a higher positive voltage than the negative lead. If it is connected in reverse the insulating layer inside the capacitor will be "dissolved" and the capacitor will be permanently damaged.Explosion may also occur if capacitor is connected to voltage that exceeds its working voltage. In order to prevent such instances, one of the capacitor's connectors is very clearly marked with a + or -, while the working voltage is printed on the case.Several models of electrolytic capacitors, as well as their symbols, are shown on the picture below.

Fig. 2.4: Electrolytic capacitorsTantalum capacitors represent a special type of electrolytic capacitor. Their parasitic inductance is much lower than standard aluminum electrolytic capacitors so that tantalum capacitors with significantly (even ten times) lower capacity can completely substitute an aluminum electrolytic capacitor.2.3 Variable capacitorsVariable capacitors are capacitors with variable capacity. Their minimal capacity ranges from 1p and their maximum capacity goes as high as few hundred pF (500pF max). Variable capacitors are manufactured in various shapes and sizes, but common features for them is a set of fixed plates (called the stator) and a set of movable plates. These plates are fitted into each other and can be taken into and out of mesh by rotating a shaft. The insulator (dielectric) between the plates is air or a thin layer of plastic, hence the name variable capacitor. When adjusting these capacitors, it is important that the plates do not touch.Below are photos of air-dielectric capacitors as well as mylar-insulated variable capacitors (2.5a).

Fig. 2.5: a, b, c. Variable capacitors, d. Trimmer capacitorsThe first photo shows a "ganged capacitor" in which two capacitors are rotated at the same time. This type of capacitor is used inradio receivers. The larger is used for the tuning circuit,andthe smaller one in the local oscillator. The symbol for these capacitors is also shown in the photo.Beside capacitors with air dielectric, there are also variable capacitors with solid insulator. With these, thin insulating material such as mylar occupies the space between stator and rotor. These capacitors are much more resistant to mechanical damage. They are shown in figure 2.5b.The most common devices containing variable capacitors are radio receivers, where these are used for frequency adjustment. Semi-variable or trim capacitors are miniature capacitors, with capacity ranging from several pF to several tens of pFs. These are used for fine tuning radio receivers, radio transmitters, oscillators, etc. Three trimmers, along with their symbol, are shown on the figure 2.5d.2.4 Practical examplesSeveral practical examples using capacitors are shown in figure 2.6. A 5F electrolytic capacitor is used for DC blocking. It allows the signal to pass from one sage to the next while prevent the DC on one stage from being passed to the next stage. This occurs because the capacitor acts like a resistor of very low resistance for the signals and as a resistor of high resistance for DC.

Fig. 2.6: a. Amplifier with headphones, b. Electricalband-switchThe figure 2.6b represents a diagram of a band-switch with two speakers, with Z1 used for reproducing low and mid-frequency signals, and Z2 for high frequency signals. 1 and 2 are connected to the audio amplifier output. Coils L1 and L2 and the capacitor C ensure that low and mid-frequency currents flow to the speaker Z1, while high frequency currents flow to Z2. How this works exactly ? In the case of a high frequency current, it can flow through either Z1 and L1 or Z2 and C. Since the frequency is high, impedance (resistance) of the coils are high, while the capacitor's reactance is low. It is clear that in this case, current will flow through Z2. In similar fashion, in case of low-frequency signals, current will flow through Z1, due to high capacitor reactance and low coil impedance.

Fig. 2.6: c. Detector radio-receiverThe figure 2.6c represents a circuit diagram for a simple detector radio-receiver (commonly called a "crystal set"), where the variable capacitor C, forming the oscillatory circuit with the coil L, is used for frequency tuning. Turning the capacitor's rotor changes the resonating frequency of the circuit, and when matching a certain radio frequency, the station can be heard.3. Coils and transformers3.1 CoilsCoils are not a very common component in electronic circuits, however when they are used, they need to be understood. They are encountered in oscillators, radio-receivers, transmitter and similar devices containing oscillatory circuits. In amateur devices, coils can be made by winding one or more layers of insulated copper wire onto a former such as PVC, cardboard, etc. Factory-made coils come in different shapes and sizes, but the common feature for all is an insulated body with turns of copper wire.The basic characteristic of every coil is its inductance. Inductance is measured in Henry (H), but more common are millihenry (mH) andmicrohenry (H) as one Henry is quite a high inductance value. As a reminder:1H = 1000mH = 106H.Coil inductance is marked byXL, and can be calculated using the following formula:

wherefrepresents the frequency of the voltage in Hz and theLrepresents the coil inductance in H.For example, if f equals 684 kHz, while L=0.6 mH, coil impedance will be:

The same coil would have three times higher impedance at three times higher frequency. As can be seen from the formula above, coil impedance is in direct proportion to frequency, so that coils, as well as capacitors, are used in circuits for filtering at specified frequencies. Note that coil impedance equals zero for DC (f=0).Several coils are shown on the figures 3.1, 3.2, 3.3, and 3.4.The simplest coil is a single-layer air core coil. It is made on a cylindrical insulator (PVC, cardboard, etc.), as shown in figure 3.1. In the figure 3.1a, turns have space left between them, while the common practice is to wind the wire with no space between turns. To prevent the coil unwinding, the ends should be put through small holes as shown in the figure.

Fig. 3.1: Single-layer coilFigure 3.1b shows how the coil is made. If the coil needs120 turns with a tapping on the thirtieth turn, there are two coils L1 with 30 turns and L2 with 90 turns. When the end of the first and the beginning of the second coil are soldered, we get a "tapping."A multilayered coil is shown in figure 3.2a. The inside of the plastic former has a screw-thread, so that the ferromagneticcore in the shape of a small screw can be inserted. Screwing the core moves it along the axis and into the center of the coil to increase the inductance. In this manner, fine changes to the inductance can be made.

Fig. 3.2: a. Multi-layered coil with core, b. Coupled coilsFigure 3.2b shows a high-frequency transformer. As can be seen, these are twocoils are coupled by magnetic induction on a shared body. When the coils are required to have exact inductance values, each coil has a ferromagnetic core that can be adjusted along the coil axis.At very high frequencies (above 50MHz) coil inductance is small, so coils need only a few turns. These coils are made of thick copper wire (approx. 0.5mm) with no coil body, as shown on the figure 3.3a. Their inductance can be adjusted by physically stretching or squeezing the turns together.

Fig. 3.3: a. High frequency coil,b. Inter-frequency transformerFigure 3.3b shows a metal casing containing two coils, with the schematic on the right. The parallel connection of the first coil and capacitor C forms an oscillatory circuit. The second coil is used for transferring the signal to the next stage. This is used in radio-receivers and similar devices. The metal casing serves as a screen to prevent external signals affecting the coils. For the casing to be effective, it must be earthed.Fig 3.4 shows a "pot core" inductor. The core is made in two halves and are glued together. The core is made of ferromagnetic material, commonly called "ferrite." These inductors are used at frequencies up to 100kHz. Adjustment of the inductance can be made by the brass or steel screw in the centre of the coil.

Fig. 3.4: A "pot core" inductor3.2 TransformersFor electronic devices to function it is necessary to have a DC power supply. Batteries and rechargeable cells can fulfill the role, but a much more efficient way is to use a POWER SUPPLY. The basic component of a power supplyr is a transformer to transform the 220V "mains" to a lower value, say 12V. A common type of transformer has one primary winding which connects to the 220V and one (or several) secondary windings for the lower voltages. Most commonly, cores are made of E and I laminations, but some are made of ferromagnetic material. There are also iron core transformers used for higher frequencies. Various types of transformers are shown on the picture below.

Fig. 3.5: Various types of transformersSymbols for a transformer are shown on the figure 3.6Two vertical lines indicate that primary and secondary windings share the same core.

Fig. 3.6: Transformer symbolsWith the transformer, manufacturers usually supply a diagram containing information about the primary and secondary windings, the voltages and maximal currents. In the case where the diagram is missing, there is a simple method for determining which winding is the primary and which is the secondary: a primary winding consists of thinner wire and more turns than the secondary. It has a higher resistance - and can be easily be tested by ohmmeter. Figure 3.6d shows the symbol for a transformer with two independent secondary windings, one of them has three tappings, giving a total of 4 different output voltages. The 5v secondary is made of thinner wire with a maximal current of 0.3A, while the other winding is made of thicker wire with a maximal current of 1.5A. Maximum voltage on the larger secondary is 48V, as shown on the figure. Note that voltages other than those marked on the diagram can be produced - for example, a voltage between tappings marked 27V and 36V equals 9V, voltage between tappings marked 27V and 42V equals 15V, etc.3.2.1 Working principles and basic characteristicsAs already stated, transformers consist of two windings, primary and the secondary (figure 3.7). When the voltageUpis connected to the primary winding (in our case the "mains" is 220V), AC currentIpflows through it. This current creates a magnetic field which passes to the secondary winding via the core of the transformer, inducing voltageUs(24V in our example). The "load" is connected to the secondary winding, shown in the diagram asRp(30 in our example). A typical load could be an electric bulb working at 24V with a consumption of 19.2W.

Fig. 3.7: Transformer: a. Working principles, b. SymbolTransfer of electrical energy from the primary to the secondary is done via a magnetic field (called "flux") and a magnetic circuit called the "core of the transformer." To prevent losses, it is necessary to make sure the whole magnetic field created by the primary passes to the secondary. This is achieved by using an iron core, which has much lower magnetic resistance than air.Primary voltage is the "mains" voltage. This value can be 220V or 110V, depending on the country. Secondary voltage is usually much lower, such as 6V, 9V, 15V, 24V, etc, but can also be higher than 220V, depending on the transformer's purpose. Relation of the primary and secondary voltage is given with the following formula:

whereNsandNprepresent the number of turns on the primary and secondary winding, respectively. For instance, ifNsequals 80 andNpequals 743, secondary voltage will be:

Relationship between the primary and secondary current is determined by the following formula:

For instance, ifRpequals 30, then the secondary current equalsIp=Up/Rp= 24V/30 = 0.8A. IfNsequals 80 andNpequals 743, primary current will be:

Transformer wattage can be calculated by the following formulae:

In our example, the power equals:

Everything up to this point relates to the ideal transformer. Clearly, there is no such thing as perfect, as losses are inevitable. They are present due to the fact that the windings exhibit a certain resistance value, which makes the transformer warm up during operation, and the fact that the magnetic field created by the primary does not entirely pass to the secondary. This is why the output wattage is less than the input wattage. Their ratio is called EFFICIENCY:

For transformers delivering hundreds of watts, efficiency is about =0.85, meaning that 85% of the electrical energy taken from the mains gets to the consumer, while the 15% is lost due to previously mentioned factors in the form of heat. For example, if power required by the consumer equalsUp*Ip= 30W, then the power which the transformer draws from the maains equals:

To avoid any confusion here, bear in mind that manufacturers have already taken every measure in minimizing the losses of transformers and other electronic components and that, practically, this is the highest possible efficiency. When acquiring a transformer, you should only worry about the required voltage and the maximal current of the secondary. Dividing the wattage and the secondary voltage gets you the maximal current value for the consumer. Dividing the wattage and the primary voltage gets you the current that the transformer draws from network, which is important to know when buying the fuse. Anyhow, you should be able to calculate any value you might need using the appropriate formulae from above.3.3 Practical examples with coils and transformers

On the figure 2.6b coils, along with the capacitor, form two filters for conducting the currents to the speakers.The coil and capacitor C on figure 2.6c form a parallel oscillatory circuit for "amplifying" a particular radio signal, while rejecting all other frequencies.

Fig. 2.6: a. Amplifier with headphones, b.Band-switch, c.Detector radio-receiverThe most obvious application for a transformer is in a power supply. A typical transformer is shown in figure 3.8 and is used for converting 220V to 24V.

Fig. 3.8: Stabilized converter with circuit LM317Output DC voltage can be adjusted via a linear potentiometer P, in 3~30V range.

Fig. 3.9: a. Stabilized converter with regulator 7806, b. auto-transformer, c.transformer for devices working at 110V, d. isolating transformerFigure 3.9a shows a simple power supply, using a transformer with a centre-tap on the secondary winding. This makes possible the use two diodes instead of the bridgeinfigure 3.8.Specialtypesof transformers,mainly used in laboratories, are auto-transformers. The diagram for an auto-transformer is shown in figure 3.9b. It features only one winding, wound on an iron core. Voltage is taken from the transformer via a slider. When the slider is in its lowest position, voltage equals zero. Moving the slider upwards increases the voltage U, to 220V. Further moving the slider increases the voltage U above 220V.The transformer in figure 3.9c converts 220v to 110v and is used for supplying devices designed to work on 110V.As a final example, figure 3.9d represents an isolating transformer. This transformer features the same number of turns on primary and secondary windings. Secondary voltage is the same as the primary, 220V, but is completely isolated from the "mains," minimizing the risks of electrical shock. As a result, a person can stand on a wet floor and touch any part of the secondary without risk, which is not the case with the normal power outlet.4. TransistorsTransistors are active components and are found everywhere in electronic circuits. They are used as amplifiers and switching devices. As amplifiers, they are used in high and low frequency stages, oscillators, modulators, detectors and in any circuit needing to perform a function. In digital circuits they are used as switches.

There is a large number of manufacturers around the world who produce semiconductors (transistors are members of this family of components), so there are literally thousands of different types. There are low, medium and high power transistors, for working with high and low frequencies, for working with very high current and/or high voltages. Several different transistors are shown on 4.1.

The most common type of transistor is called bipolar and these are divided into NPN and PNP types.Their construction-material is most commonly silicon (their marking has the letter B) or germanium (their marking has the letter A). Original transistor were made from germanium, but they were very temperature-sensitive. Silicon transistors are much more temperature-tolerant and much cheaper to manufacture.

Fig. 4.1: Different transistors

Fig. 4.2: Transistor symbols: a - bipolar, b - FET, c -MOSFET, d - dual gate MOSFET,e - inductive channel MOSFET, f - single connection transistorThe second letter in transistors marking describes its primary use:C - low and medium power LF transistor,D - high power LF transistor,F - low power HF transistor,G - other transistors,L - high power HF transistors,P - photo transistor,S - switch transistor,U - high voltage transistor.

Here are few examples:AC540 - germanium core, LF, low power,AF125 - germanium core, HF, low power,BC107 - silicon, LF, low power (0.3W),BD675 - silicon, LF, high power (40W),BF199 - silicon, HF (to 550 MHz),BU208 - silicon (for voltages up to 700V),BSY54 - silicon, switching transistor.There is a possibility of a third letter (R and Q - microwave transistors, or X - switch transistor), but these letters vary from manufacturer to manufacturer.The number following the letter is of no importance to users.American transistor manufacturers have different marks, with a 2N prefix followed by a number (2N3055, for example). This mark is similar to diode marks, which have a 1N prefix (e.g. 1N4004).Japanese bipolar transistor are prefixed with a: 2SA, 2SB, 2SC or 2SD, and FET-s with 3S:2SA - PNP, HF transistors,2SB - PNP, LF transistors,2SC - NPN, HF transistors,2SD - NPN, HF transistors.

Several different transistors are shown in photo 4.1, and symbols for schematics are on 4.2. Low power transistors are housed in a small plastic or metallic cases of various shapes. Bipolar transistors have three leads: for base (B), emitter (E), and for collector (C). Sometimes, HF transistors have another lead which is connected to the metal housing. This lead is connected to the ground of the circuit, to protect the transistor from possible external electrical interference. Four leads emerge from some other types, such as two-gate FETs. High power transistors are different from low-to-medium power, both in size and in shape.

It is important to have the manufacturers catalog or a datasheet to know which lead is connected to what part of the transistor. These documents hold the information about the component's correct use (maximum current rating, power, amplification, etc.) as well as a diagram of the pinout. Placement of leads and different housing types for some commonly used transistors are in diagram 4.3.

Fig. 4.3: Pinouts of some common packagesIt might be useful to remember the pinout for TO-1, TO-5, TO-18 and TO-72 packages and compare them with the drawing 4.2 (a). These transistors are the ones you will come across frequently in everyday work.

The TO-3 package, which is used to house high-power transistors, has only two pins, one for base, and one for emitter. The collector is connected to the package, and this is connected to the rest of the circuit via one of the screws which fasten the transistor to the heat-sink.

Transistors used with very high frequencies (like BFR14) have pins shaped differently.One of the breakthroughs in the field of electronic components was the invention of SMD (surface mount devices) circuits. This technology allowed manufacturers to achieve tiny components with the same properties as their larger counterparts, and therefore reduce the size and cost of the design. One of the SMD housings is the SOT23 package. There is, however, a trade-off to this, SMD components are difficult to solder to the PC board and they usually need special soldering equipment.

As we said, there are literally thousands of different transistors, many of them have similar characteristics, which makes it possible to replace a faulty transistor with a different one. The characteristics and similarities can be found in comparison charts. If you do not have one these charts, you can try some of the transistors you already have. If the circuit continues to operate correctly, everything is ok. You can only replace an NPN transistor with an NPN transistor. The same goes if the transistor is PNP or a FET. It is also necessary to make sure the pinout is correct, before you solder it in place and power up the project.As a helpful guide, there is a chart in this chapter which shows a list of replacements for some frequently used transistors.4.1 The working principle of a transistorTransistors are used in analog circuits to amplify a signal. They are also used in power supplies as a regulator and you will also find them used as a switch in digital circuits.The best way to explore the basics of transistors is by experimenting. A simple circuit is shown below. It uses a power transistor to illuminate a globe. You will also need a battery, a small light bulb (taken from a flashlight) with properties near 4.5V/0.3A, a linear potentiometer (5k) and a 470 ohm resistor. These components should be connected as shown in figure 4.4a.

Fig. 4.4: Working principle of a transistor: potentiometer moves toward its upper position - voltage on the base increases- current through the base increases - current through the collector increases - the brightness of the globe increases.

Resistor (R) isn't really necessary, but if you don't use it, you mustn't turn the potentiometer (pot) to its high position, because that would destroy the transistor - this is because the DC voltage UBE (voltage between the base and the emitter), should not be higher than 0.6V, for silicon transistors.

Turn the potentiometer to its lowest position. This brings the voltage on the base (or more correctly between the base and ground) to zero volts (UBE = 0). The bulb doesn't light, which means there is no current passing through the transistor.

As we already mentioned, the potentiometers lowest position means that UBE is equal to zero. When we turn the knob from its lowest position UBE gradually increases. When UBE reaches 0.6v, current starts to enter the transistor and the globe starts to glow. As the pot is turned further, the voltage on the base remains at 0.6v but the current increases and this increases the current through the collector-emitter circuit. If the pot is turned fully, the base voltage will increase slightly to about 0.75v but the current will increase significantly and the globe will glow brightly.

If we connected an ammeter between the collector and the bulb (to measure IC), another ammeter between the pot and the base (for measuring IB), and a voltmeter between the ground and the base and repeat the whole experiment, we will find some interesting data. When the pot is in its low position UBE is equal to 0V, as well as currents IC and IB. When the pot is turned, these values start to rise until the bulb starts to glow when they are: UBE = 0.6V, IB = 0.8mA and IB = 36 mA (if your values differ from these values, it is because the 2N3055 the writer used doesn't have the same specifications as the one you use, which is common when working with transistors).The end result we get from this experiment is that when the current on the base is changed, current on the collector is changed as well.

Let's look at another experiment which will broaden our knowledge of the transistor. It requires a BC107 transistor (or any similar low power transistor), supply source (same as in previous experiment), 1M resistor, headphones and an electrolytic capacitor whose value may range between 10u to 100F with any operating voltage.A simple low frequency amplifier can be built from these components as shown in diagram 4.5.

Fig. 4.5: A simple transistor amplifierIt should be noted that the schematic 4.5a is similar to the one on 4.4a. The main difference is that the collector is connected to headphones. The "turn-on" resistor - the resistor on the base, is 1M. When there is no resistor, there is no current flow IB, and no Ic current. When the resistor is connected to the circuit, base voltage is equal to 0.6V, and the base current IB = 4A. The transistor has a gain of 250 and this means the collector current will be 1 mA. Since both of these currents enter the transistor, it is obvious that the emitter current is equal to IE = IC + IB. And since the base current is in most cases insignificant compared to the collector current, it is considered that:

The relationship between the current flowing through the collector and the current flowing through the base is called the transistor's current amplification coefficient, and is marked as hFE. In our example, this coefficient is equal to:

Put the headphones on and place a fingertip on point 1. You will hear a noise. You body picks up the 50Hz AC "mains" voltage. The noise heard from the headphones is that voltage, only amplified by the transistor. Let's explain this circuit a bit more. Ac voltage with frequency 50Hz is connected to transistor's base via the capacitor C. Voltage on the base is now equal to the sum of a DC voltage (0.6 approx.) via resistor R, and AC voltage "from" the finger. This means that this base voltage is higher than 0.6V, fifty times per second, and fifty times slightly lower than that. Because of this, current on the collector is higher than 1mA fifty times per second, and fifty times lower. This variable current is used to shift the membrane of the speakerphones forward fifty times per second and fifty times backwards, meaning that we can hear the 50Hz tone on the output.Listening to a 50Hz noise is not very interesting, so you could connect to points 1 and 2 some low frequency signal source (CD player or a microphone).

There are literally thousands of different circuits using a transistor as an active, amplifying device. And all these transistors operate in a manner shown in our experiments, which means that by building this example, you're actually building a basic building block of electronics.

4.2 Basic characteristics of transistorsSelecting the correct transistor for a circuit is based on the following characteristics: maximum voltage rating between the collector and the emitter UCEmax, maximum collector current ICmax and the maximum power rating PCmax.If you need to change a faulty transistor, or you feel comfortable enough to build a new circuit, pay attention to these three values. Your circuit must not exceed the maximum rating values of the transistor. If this is disregarded there are possibilities of permanent circuit damage. Beside the values we mentioned, it is sometimes important to know the current amplification, and maximum frequency of operation.When there is a DC voltage UCE between the collector (C) and emitter (E) with a collector current, the transistor acts as a small electrical heater whose power is given with this equation:

Because of that, the transistor is heating itself and everything in its proximity. When UCE or ICE rise (or both of them), the transistor may overheat and become damaged. Maximum power rating for a transistor, is PCmax (found in a datasheet). What this means is that the product of UCE and IC should should not be higher than PCmax:

So, if the voltage across the transistor is increased, the current must be dropped.For example, maximum ratings for a BC107 transistor are:ICmax=100mA,UCEmax = 45V andPCmax = 300mWIf we need a Ic=60mA , the maximum voltage is:

For UCE = 30V, the maximum current is:

Among its other characteristics, this transistor has current amplification coefficient in range between hFE= 100 to 450, and it can be used for frequencies under 300MHz. According to the recommended values given by the manufacturer, optimum results (stability, low distortion and noise, high gain, etc.) are with UCE=5V and IC=2mA.There are occasions when the heat generated by a transistor cannot be overcome by adjusting voltages and current. In this case the transistors have a metal plate with hole, which is used to attach it to a heat-sink to allow the heat to be passed to a larger surface.

Current amplification is of importance when used in some circuits, where there is a need for equal amplification of two transistors. For example, 2N3055H transistors have hFE within range between 20 and 70, which means that there is a possibility that one of them has 20 and other 70. This means that in cases when two identical coefficients are needed, they should be measured. Some multimeters have the option for measuring this, but most don't. Because of this we have provided a simple circuit (4.6) for testing transistors. All you need is an option on your multimeter for measuring DC current up to 5mA. Both diodes (1N4001, or similar general purpose silicon diodes) and 1k resistors are used to protect the instrument if the transistor is "damaged". As we said, current gain is equal to hFE = IC / IB. In the circuit, when the switch S is pressed, current flows through the base and is approximately equal to IB=10uA, so if the collector current is displayed in milliamps. The gain is equal to:

For example, if the multimeter shows 2.4mA, hFE = 2.4*100 = 240.

Fig. 4.6: Measuring the hFEWhile measuring NPN transistors, the supply should be connected as shown in the diagram. For PNP transistors the battery is reversed. In that case, probes should be reversed as well if you're using analog instrument (one with a needle). If you are using a digital meter (highly recommended) it doesn't matter which probe goes where, but if you do it the same way as you did with NPN there would be a minus in front of the read value, which means that current flows in the opposite direction.4.3 The safest way to test transistorsAnother way to test transistor is to put it into a circuit and detect the operation. The following circuit is a multivibrator. The "test transistor" is T2. The supply voltage can be up to 12v. The LED will blink when a good transistor is fitted to the circuit.

Fig. 4.7: Oscillator to test transistorsTo test PNP transistors, same would go, only the transistor which would need to be replaced is the T1, and the battery, LED, C1 and C2 should be reversed.4.4 TUN and TUPAs we previously said, many electronic devices work perfectly even if the transistor is replaced with a similar device. Because of this, many magazines use the identification TUN and TUP in their schematics. These are general purpose transistors. TUN identifies a general purpose NPN transistor, and TUP is a general purpose PNP transistor.

TUN = Transistor Universal NPN and TUP = Transistor Universal PNP.

These transistors have following characteristics:

4.5 Practical exampleThe most common role of a transistor in an analog circuit is as an active (amplifying) component. Diagram 4.8 shows a simple radio receiver - commonly called a "Crystal Set with amplifier."Variable capacitor C and coil L form a parallel oscillating circuit which is used to pick out the signal of a radio station out of many different signals of different frequencies. A diode, 100pF capacitor and a 470k resistorform a diode detector which is used to transform the low frequency voltage into information (music, speech). Information across the 470k resistor passes through a 1uF capacitor to the base of a transistor. The transistor and its associated components create a low frequency amplifier which amplifies the signal.On figure 4.8 there are symbols for a common ground and grounding. Beginners usually assume these two are the same which is a mistake. On the circuit board the common ground is a copper track whose size is significantly wider than the other tracks. When this radio receiver is built on a circuit board, common ground is a copper strip connecting holes where the lower end of the capacitor C, coil L 100pF capacitor and 470k resistor are soldered. On the other hand, grounding is a metal rod stuck in a wet earth (connecting your circuits grounding point to the plumbing or heating system of your house is also a good way to ground your project).Resistor R2 biases the transistor. This voltage should be around 0.7V, so that voltage on the collector is approximately equal to half the battery voltage.

Fig. 4.8: Detector receiver with a simple amplifier

5. DiodesAs with transistors, diodes are fabricated from semi-conducting material. So, the first letter in their identification is A for germanium diode or B for silicon diode. They can be encased in glass, metal or a plastic housing. They have two leads: cathode (k) and an anode (A). The most important property of all diodes is their resistance is very low in one direction and very large in the opposite direction.When a diode is measured with a multimeter and it reads a low value of ohms, this is not really the resistance of the diode. It represents the voltage drop across the junction of the diode. This means a multimeter can only be used to detect if the junction is not damaged. If the reading is low in one direction and very high in the other direction, the diode is operational.

When a diode is placed in a circuit and the voltage on the anode is higher than the cathode, it acts like a low value resistor and current will flow.If it is connected in the opposite direction it acts like a large value resistor and current does not flow.In the first case the diode is said to be "forward biased" and in the second case it is "reverse biased."

Figure 5.1 shows several different diodes:

Fig. 5.1: Several different types of diodesThe diodes above are all single diodes, however 4 diodes are available in a single package. This is called a BRIDGE or BRIDGE RECTIFIER. Examples of a bridge are shown in the diagram below:

You must be able to identify each of the 4 leads on a bridge so that it can be inserted into a circuit around the correct way. The surface-mount device above is identified by a cut @ 45 along one side. The leaded bridge has one leg longer than the others and the top is marked with AC marks and "+." The high-current bridge has a corner cut off and the other surface-mount device has a cut or notch at one end.These devices are added to a circuit as shown in the next diagram:

The 4 diodes face the same direction and this means a single diode can be shown on the circuit diagram:

Symbols in 5.2 show a number of diodes. There are a number of specially-designed diodes: for high current, high-speed, low voltage-drop, light-detection, and varying capacitance as the voltage is altered. Most diodes are made from silicon as it will withstand high temperature, however germanium is used if a low voltage-drop is required. There is also a light emitting diode called a LED, but this is a completely different type of diode.

Fig. 5.2: Diode symbols: a - standard diode, b -LED,c, d - Zener, e - photo, f,g - tunnel, h - Schottky, i - breakdown,j - capacitativeLEDs (Light Emitting Diodes) are constructed from a crystalline substance that emits light when a current flows through it. Depending on the crystalline material: red, yellow, green, blue or orange light is produced. The photo below shows some of the colours hat can be produced by LEDs:

It is not possible to produce white light from any of these materials, so a triad of red, blue and green is placed inside a case and they are all illuminated at the same time to produce white light. Recently, while light has been produced from a LED by a very complex and interesting process that can be found on Wikipedia:http://en.wikipedia.org/wiki/LED

LEDs have a cathode and anode lead and must be connected to DC around the correct way. The cathode lead is identified on the body by a flat-spot on the side of the LED. The cathode lead is the shorter lead.

One of the most important things to remember about a LED is the characteristic voltage that appears across it when connected to a voltage. This does not change with brightness and cannot be altered.For a red LED, this voltage is 1.7v and if you supply it with more than this voltage, it will be damaged.The easy solution is to place a resistor on one lead as shown in the diagram below:

The LED will allow the exact voltage to appear across it and the brightness will depend on the value of the resistor.

Zener diodes (5.2c and 5.2d) are designed to stabilize a voltage. Diodes marked as ZPD5.6V or ZPY15V have operating voltages of 5.6V and 15V.

Photo diodes (5.2e) are constructed in a way that they allow light to fall on the P-N connection. When there is no light, a photo diode acts as a regular diode. It has high resistance in one direction, and low resistance in opposite direction. When there is light, both resistances are low. Photo diodes and LEDs are the main items in an optocoupler (to be discussed in more detail in chapter 9).

Tunnel diodes (5.2f and 5.2g) are commonly used in oscillators for very high frequencies.

Schottky diodes (5.2h) are used in high frequency circuits and for its low voltage drop in the forward direction.

Breakdown diodes (5.2i) are actually Zener diodes. They are used in various devices for protection and voltage regulation. It passes current only when voltage rises above a pre-defined value.

A Varicap diode (5.2j) is used instead of a variable capacitor in high frequency circuits. When the voltage across it is changed, the capacitance between cathode and anode is changed. This diode is commonly used in radio receivers, transceivers and oscillators.

The cathode of a low power diode is marked with a ring painted on the case, but it is worth noting that some manufacturers label the anode this way, so it is best to test it with a multimeter.

Power diodes are marked with a symbol engraved on the housing. If a diode is housed in a metal package, the case is generally the cathode and anode is the lead coming from the housing.5.1 Diode identificationEuropean diodes are marked using two or three letters and a number. The first letter is used to identify the material used in manufacturing the component (A - germanium, B - silicon), or, in case of letter Z, a Zener diode.The second and third letters specify the type and usage of the diode. Some of the varities are:A - low power diode, like the AA111, AA113, AA121, etc. - they are used in the detector of a radio receiver; BA124, BA125 : varicap diodes used instead of variable capacitors in receiving devices, oscillators, etc., BAY80, BAY93, etc. - switching diodes used in devices using logic circuits. BA157, BA158, etc. - these are switching diodes with short recovery time.B - two capacitive (varicap) diodes in the same housing, like BB104, BB105, etc.Y - regulation diodes, like BY240, BY243, BY244, etc. - these regulation diodes come in a plastic packaging and operate on a maximum current of 0.8A. If there is another Y, the diode is intended for higher current. For example, BYY44 is a diode whose absolute maximum current rating is 1A. When Y is the second letter in a Zener diode mark (ZY10, ZY30, etc.) it means it is intended for higher current.G, G, PD - different tolerance marks for Zener diodes. Some of these are ZF12 (5% tolerance), ZG18 (10% tolerance), ZPD9.1 (5% tolerance).The third letter is used to specify a property (high current, for example).American markings begin with 1N followed by a number, 1N4001, for example (regulating diode), 1N4449 (switching diode), etc.Japanese style is similar to American, the main difference is that instead of N there is S, 1S241 being one of them.5.2 Diode characteristicsThe most important characteristics when using power diodes is the maximum current in the forward direction (IFmax), and maximum voltage in the reverse direction (URmax).

The important characteristics for a Zener diode are Zener voltage (UZ), Zener current (IZ) and maximum dissipation power (PD).

When working with capacitive diodes it is important to know their maximum and minimum capacitance, as well as values of DC voltage during which these capacitances occur.

With LEDs it is important to know the maximum value of current it is capable of passing. The natural characteristic voltage across a LED depends on the colour and starts at 1.7V for red to more than 2.4v for green and blue.Current starts at 1mA for a very small glow and goes to about 40mA. High brightness LEDs and "power LEDs" require up to 1 amp and more. You must know the exact current required by the LED you are using as the wrong dropper resistor will allow too much current to flow and the LED will be damagedinstantly.The value of this resistors will be covered in another chapter.

Beside universal transistors TUN and TUP (mentioned in Chapter 4.4), there are universal diodes as well. They are marked with DUS (for universal silicon diode) and DUG (for germanium) on circuit diagrams.

DUS = Diode Universal Silicon DUG = Diode Universal Germanium5.3 Practical examplesThe diagram of a power supply in figure (3.8) uses several diodes. The first four are in a single package, identified by B40C1500. This is a bridge rectifier.The LED in the circuit indicates the transformer is working. Resistor R1 is used to limit the current through the LED and the brightness of the LED indicates the approximate voltage.Diodes marked 1N4002 protect the integrated circuit.

Figure 5.3 below shows some other examples of diodes. The life of a globe can be increased by adding a diode as shown in 5.3a. By simply connecting it in series, the current passing through the globe is halved and it lasts a lot longer. However the brightness is reduced and the light becomes yellow. The Diode should have a reverse voltage of over 400V, and a current higher than the globe. A 1N4004 or BY244 is suitable.

A very simple DC voltage stabilizer for low currents can be made using 5.3c as a reference.\6. Thyristors, triacs, diacsThere are several thyristors displayed on 6.1. Triacs look the same, while diacs look like small power rectifying diodes. Their symbols, and pin-out is found in figure 6.2.

Fig. 6.1: Several thyristors and triacsA thyristor is an improved diode. Besides anode (A) and cathode (k) it has another lead which is commonly described as a gate (G), as found on picture 6.2a. The same way a diode does, a thyristor conducts current when the anode is positive compared to the cathode, but only if the voltage on the gate is positive and sufficient current is flowing into the gate to turn on the device. When a thyristor starts conducting current into the gate is of no importance and thyristor can only be switched off by removing the current between anode and cathode. For example, see figure 6.3. If S1 is closed, the thyristor will not conduct, and the globe will not light. If S2 is closed for a very short time, the globe will illuminate. To turn off the globe, S1 must be opened. Thyristors are marked in some circuits as SCR, which is an acronym for Silicon Controlled Rectifier.A triac is very similar to a thyristor, with the difference that it can conduct in both directions. It has three electrodes, called anode 1 (A1), anode 2 (A2), and gate (G). It is used for regulation of alternating current circuits. Devices such as hand drills or globes can be controlled with a triac.

Thyristors and triacs are marked alphanumerically, KT430, for example.Low power thyristors and triacs are packed in same housings as transistors, but high power devices have a completely different housing. These are shown in figure 6.1. Pin-outs of some common thyristors and triacs are shown in 6.2 a and b.Diacs (6.2c), or two-way diodes as they are often referred to, are used together with thyristors and triacs. Their main property is that their resistance is very large until voltage on their ends exceeds some predefined value. When the voltage is under this value, a diac responds as a large value resistor, and when voltage rises it acts as a low value resistor.

Fig. 6.2: Symbols and pin placements for: a - thyristor, b - triac, c - diac

Fig. 6.3: Thyristor principleofwork6.1 Practical examplesPicture 6.5 detects when light is present in a room. With no light, the photo-transistor does not conduct. When light is present, the photo-transistor conducts and the bell is activated. Turning off the light will not stop the alarm. The alarm is turned off via S1.

Fig. 6.5: Alarm device using a thyristor and a photo-transistorA circuit to flash a globe is shown in figure 6.6 This circuit flashes a 40w globe several times per second. Mains voltage is regulated using the 1N4004 diode. The 220u capacitor charges and its voltage rises. When this voltage reaches the design-voltage of the the diac (20v), the capacitor discharges through the diac and into the triac. This switches the triac on and lights the bulb for a very short period of time, after a period of time (set by the 100k pot), the capacitor is charged again, and the whole cycle repeats. The 1k trim pot sets the current level which is needed to trigger the triac.

Fig. 6.6: FlasherA circuit to control the brightness of a globe or the speed of a motor is shown in figure 6.7

Fig. 6.7: Light bulb intensity or motor speed controllerIf the main use for this circuit is to control the brightness of a light bulb, RS and CS are not necessary.

Fig. 5.3: a - using a diode to prolong the light bulb's life span, b -stair-light LED indicator,c - voltage stabilizer, d - voltage rise indicator, e - rain noise synthesizer, f - backup supplyUnstabilized voltage is marked "U", and stabilized with "UST." Voltage on the Zener diode is equal to UST, so if we want to achieve a stabilized 9V, we would use a ZPD9.1 diode. Although this stabilizer has limited use it is the basis of all designs found in power supplies.We can also devise a voltage overload detector as sown in figure 5.3d. A LED indicates when a voltage is over a predefined value. When the voltage is lower than the operating voltage of the Zener, the zener acts as a high value resistor, so DC voltage on the base of the transistor is very low, and the transistor does not "turn on." When the voltage rises to equal the Zener voltage, its resistance is lowered, and transistor receives current on its base and it turns on to illuminate the LED. This example uses a 6V Zener diode, which means that the LED is illuminated when the voltage reaches that value. For other voltage values, different Zener diodes should be used. Brightness and the exact moment of illuminating the LED can be set with the value of Rx.To modify this circuit so that it signals when a voltage drops below some predefined level, the Zener diode and Rx are swapped. For example, by using a 12V Zener diode, we can make a car battery level indicator. So, when the voltage drops below 12V, the battery is ready for recharge.Figure 5.3e shows a noise-producing circuit, which produces a rain-like sound. DC current flowing through diode AA121 isn't absolutely constant and this creates the noise which is amplified by the transistor (any NPN transistor) and passed to a filter (resistor-capacitor circuit with values 33nF and 100k).

Figure 5.3f shows a battery back-up circuit. When the "supply" fails, the battery takes over.

7. Integrated circuitsIntegrated Circuits play a very important part in electronics. Most are specially made for a specific task and contain up to thousands of transistors, diodes and resistors. Special purposes IC's such as audio-amplifiers, FM radios, logic blocks, regulators and even a whole micro computers in the form of a micro controller can be fitted inside a tiny package. Some of the simple Integrated Circuits are shown in figure 7.1.

Fig. 7.1: Integrated circuitsDepending on the way they are manufactured, integrated circuits can be divided into two groups: hybrid and monolithic. Hybrid circuits have been around longer. If a transistor is opened, the crystal inside is very small. This means a transistor doesn't take up very much space and many of them can be fitted into a single Integrated Circuit.The pin-out for some of the common packages is shown in Figure 7.2:

Fig. 7.2: Pin-out and symbols for some common integrated circuitsMost integrated Circuits are in a DIL package - Dual In Line, meaning there are two rows of pins. (DIL16 and DIL8 are shown in 7.2b and 7.2c). The device is viewed from the top and the pins are numbered in an anti-clockwise direction.High power integrated circuits can generate a lot of heat and they have a metal tag that can be connected to a heatsink to dissipate the heat. Examples of these IC's are shown in 7.2d and 7.2e, and 7.2f.Symbols used to represent integrated circuits are shown in 7.2g and 7.2i. Symbol 7.2g is commonly used to represent amplifiers.Figure 7.2i shows an operational amplifier. Signs + and - represent inverting and non-inverting inputs. The signal to be amplified is applied between one of the inputs and ground (ground and supply aren't represented, but are necessary for the circuit to operate).Integrated circuits can be divided into two further groups:analog (linear) and digital. The output voltage of a linear circuits is continuous, and follows changes in the input. Typical representative of a linear IC is an integrated audio amplifier. When a signal from a microphone is connected to the input the output will vary in the same way as the voltage from the microphone. If watched on an oscilloscope, the signal on the output will be the same shape as the mic's signal, only the voltage will be higher depending on the amplification of the integrated circuit.It is a different situation with digital IC's. Their output voltage is not continuous. It is either LOW or HIGH and it changes from one state to the other very quickly.7.1 Analog integrated circuitsWhile on the topic of analog circuits, we will look at the LM386 IC. It has all the components for a complete audio-amplifier. Figure 7.3a shows an example of an amplifier made with this integrated circuit, which can be used as a complete amplifier for a walkman, interphone, cassette player or some other audio device. It can also be used as a test circuit for troubleshooting.

Fig. 7.3: a - A low frequency amplifier using the LM386The signal is brought to the non-inverting input (between pin 3 and ground). Inverting input (pin 2) is connected to ground. If 10F is placed between pins 1 and 8 a voltage amplification of 200 is created. If this capacitor is removed the amplification is 20. It is possible to achieve in-between amplification by adding a resistor and connecting it in series with the capacitor.One of the essential components in this circuit is the 100nF capacitor which is placed between pin 6 (which is connected to the positive of the supply) and ground. The capacitor should be ceramic and should be mounted as close to the integrated circuit as possible. This is common practice when working with integrated circuits, even when it isn't shown in the diagram as a capacitor connected between the positive and negative stabilizes the voltage and protects the circuit from spikes and a phenomenon called instability. This is due to inductance in the power supply tracks allowing high currents taken by the IC to upset its operation.7.2 Digital integrated circuitsThe CD4011 will be our "show-and-tell" IC to cover the main characteristics of digital circuits. It is a 14 pin DIL package. The pin-out is shown in figure 7.4a. Note the small half-round slit on one end of the IC. It identifies pin 1. Pins 7 and 14 connect to a supply (battery or DC power supply). Negative is connected to pin 7. Positive is connected to pin 14.There are four logic NAND gates in a CD4011 IC. Each has two inputs and one output. For gate N1 the inputs are pins 1 and 2, and output is pin 3. The symbol for a NAND gate is displayed in figure 7.4b. The inputs are marked A and B and output is F. The supply voltage can be up to 16v and as low as 5V. The output will deliver up to 10mA at 12v but this is reduced as the supply voltage is reduced.

Figure 7.4b shows the truth table for a NAND gate. It shows the output voltage (voltage between F and ground) with different input states. Because there are only two voltages for every pin, we call them states, with logic zero when the voltage is zero, and logic one when the voltage on the pin is the same as the supply voltage.From this we can read the second row of the truth table: if logic zero is on both input pins, output is logic one, third row is similar: if the first input is one, and the second one is zero, output is logic one, fourth row: if the first input is zero, and the second one is one, output is logic one. Fifth row is different, since both of its inputs are one, the definition of NAND gate states that the output is zero.

Fig. 7.4: a - 4011 pin placements, b - symbol and the truth table for NAND gates,Logic circuits have many applications, but their main use is in computer circuits.The following circuit is a simple example to show how the gates can be connected to produce a project that turns on a globe when a finger is placed on a "touch pad."The globe turns off after a period of time, determined by the value of the 470u and 2M2 resistor.

The operation of a NAND gateLets look at the functionalities of the following circuit. Both inputs of NI1 are connected to each other, so when input P is HIGH, output is zero. This logic zero is passed on to NI2, so no matter what is on the input 6, output 4 is logic one. This means that, between the ground and pin 4, the voltage is equal to 12V.

Fig. 7.5:Sensor switch using a 4011Current flows through capacitor C and resistor R, so capacitor begins to charge. Every uncharged capacitor behaves like a short circuit. Because of that, when 12V appears on pin 4, it is also present on resistor R and also on pins 8 and 9. Pin 10 shows logic zero because of this which is connected to pin 6. From now on, logic zero on pin 5 is no longer needed because only one input needs to be zero for the output to be logic one. So input P is no longer needed. Gates NI2 and NI3 maintain logic zero on pin 4. How long will this last? It depends on the value of the capacitor and resistor. As the capacitor charges, the voltage on the resistor drops and when it falls to 1/2 of the supply voltage (6V in our case), NI3 detects a low on its inputs so logic one appears on pin 10. Since logic one is now on input 5 (no logic one present on P), and on input 6, output 4 is zero, capacitor dumps its charge via diodes on the inputs on pins 8 and 9 and the circuit starts operating again.

As we saw, for a certain period of time, which is equal to T=0.7*RC output of pin 10 was logic zero. During that time output E (pin 11) is logic one. For example, if R = 2M2 and C=47F, for time T = 2.2*10^6*47*10^-6 = 94 sec from the moment impulse on input P subsided, voltage on output E is 12V.The end result of our experiment is on diagram 7.5a. Short positive pulses appearing on P in the time t1 caused a longer variable ulse on output E.Schematic 7.5b displays this circuit which allows us to light a bulb using four NAND gates interconnected in the way shown on picture 7.5a.The sensor is two copper (or some other conducting material) plates glued to some non-conducting material (plastics, wood, etc.) in close proximity to each other. So, when we touch the sensor with the tip of our finger, we close the circuit. 12V appears on input P, which in turn conducts the voltage to the output E, resistor R = 22k conducts base current and the bulb lights. When we remove our finger, output E will last for 94 seconds, after which it goes to logic zero and the light goes out.Transistor T is selected so that its maximum allowed collector current is higher than the current of the globe.(The globes current flow value is found by dividing its power by its voltage. For example, if its power is P = 6W and voltage is U = 12V, current through the globe is I = P/U = 6W/12V = 0.5A or higher. One thing you must remember with a globe is the starting or "turn-on" current. It is about six times the operating current and the transistor must be able to pass this current for the globe to illuminate.7.3 Practical examplesDiagram 7.6 shows a circuit for a stereo audio-amp using a TDA4935 IC. It is a modern integrated circuit with two separate pre-amps and stereo outputs.Left and right input signals are marked UL and UD, which are brought to two inputs of the amplifier. The chip also has built-in heat and overload protection. Maximum output for each amplifier is 15W, so they can be used in stereo mode of 2x15W amplifiers.

Fig. 7.6: Stereo audio-amplifier using the TDA4935Another example is an audio amplifier using an LM386 circuit, with a preamp using a BC107 transistor. The series connected capacitor and resistor between pins 1 and 5 produces low frequency amplification (around 100Hz) improving the characteristics of the circuit. This amplifier could be used with any low frequency source (gramophone, microphone, etc.).

Fig. 7.7: complete audio-amplifier using the LM386The third example is a simple alarm, shown in figure 7.8. It uses a CD4011 IC. Gates NI3 and NI4 form a 600Hz audio oscillator. This signal is amplified using an NPN transistor and passed to an 8R speaker. To hear the 600Hz tone, remove the connection to pin 8 and connect pin 8 to pin 9. This produces a constant tone. Gates NI1 and NI2 form a 4Hz oscillator, whose output is connected to pin 8. This turns the 600Hz tone on and off at 4Hz. To use this alarm in your home, on doors for example, connected pin 1 to 7 via a switch.

Fig. 7.8: Alarm using a CD4011 ICThe last circuit in this chapter is an example of a mono FM receiver using a TDA7088T IC, which can be, along with the SMD components, housed in a match-box along with two miniature watch batteries. You can purchase a ready-built scanning radio in a "junk shop" for as little as $5.00 with stereo head-phones Always look in the toy sections of large stores for the latest technology at the cheapest price.

Fig. 7.9: Mono FM radio receiver with an electronic presetTuning to a low frequency station is done automatically by pressing the RUN button. This turns on the part of the integrated circuit which is designated for scanning over a given range. When it finds a station it locks on until the RUN button is pressed again. When it reaches 108MHz it waits for the RESET signal which returns the scan to 88MHz.

8. Microphones, speakers and headphonesMicrophones, speakers and headphones are components commonly used as the input and output devices of many circuits. A microphone converts sound waves into electrical signals that closely follow the waveform of the sound being received. This signal is then amplified by the circuit and transformed into a sound by a speaker or headphone. The symbols for these components are shown on 8.1.

8.1 MicrophonesThere are several different types of microphone: carbon, dynamic, crystal, capacitive (electret). Carbon microphones were one of the first to be invented and were used mainly in telephone applications. But they are very noisy as the carbon granules rattle when the microphone is moved and this type is being replaced by more advanced types.

Dynamic microphones are in wide use and their quality of reproduction is superb. They are used in the recording industry for music and speech where high fidelity is required. Basically they are exactly the same as a speaker, the only difference being the size. But their only limitation is the very low output. The internal structure is shown in figure 8.2. A paper cylinder, onto which fine copper wire is wound, is connected to a membrane which moves under the force of sound pressure created by the sound source. This coil is in a narrow gap with a high magnetic field created by a permanent magnet. When the coil moves in this magnetic field, it produces a voltage identical to the sound causing the movement.Because of the low resistance (impedance) of a dynamic microphone, it usually needs a transformer so it can be connected to an amplifier (called a pre-amp). This transformer is usually built into the microphone's case, but if is absent, it is necessary to connect the microphone to a preamplifier with low input resistance.Crystal microphones contain a crystal called a "piezo crystal" that is connected to a small diaphragm. When sound waves hit the diaphragm, the crystal changes shape and it produces a voltage. This voltage is passed to an amplifier.Recently, electret microphones have improved in quality and taken over from nearly all other types of microphone. They are small, rugged, low in price and produce a very high quality output.The shape, size and characteristics are shown in 8.3.The microphone contains a Field Effect Transistor, which means it needs a DC voltage for it to operate. Figure 8.3d shows how an electret mic is connected to a circuit. It needs a "load resistor" to limit the current to the FET and the output is taken across this resistor. That's the technical way of saying the output is taken from the point where the resistor meets the FET.

8.2 SpeakersSpeakers vary enormously in size and shape. They can be designed as crystal or capacitive, but most often they are dynamic (called electro-dynamic construction).The cross-section of an electro-dynamic speaker is shown in 8.4. Ferrite rings (2, 3 and 4) are added to a large permanent magnet (1) which creates a strong magnetic field in the narrow gap between magnets North and South poles. A Cylindrical former is added to the gap and it holds coil (5). The ends of the coil are taken to the outside of the speaker.The two most important characteristics of a speaker are its resistance (we actually call the resistance of a speaker IMPEDANCE as the value is determined at a frequency of 1kHz and the value is higher than its actual resistance) and its wattage. Common impedances are 4, 8 and 16 ohm, but there are also 1.5, 40 and 80 ohm speakers. Speaker wattages range from a fraction of a watt to hundreds of watts.When choosing a speaker, it is advisable to choose the largest speaker possible as they are more efficient and produce the least distortion especially in the low frequency range. Speakers should be housed in a large box since it functions as a resonating chamber and this greatly adds to the overall quality of the sound.8.3 Headphones

There are several types of headphone: crystal and electromagnetic. The electromagnetic type is the most commonly used. They functioning in the same way as speakers, with obvious differences in construction, since they are intended for much lower power. Their main characteristic is their resistance (impedance), from a few ohms to a few thousand ohms.

The cross section of an electromagnetic headphone is shown in 8.5. It consists of a horseshoe magnet with poles that hold two coils. These are connected in series. The diaphragm is a thin steel plate. When current flows through the coils, the diaphragm is pulled towards the coils. This moves the air and the result is heard as a faithful reproduction.8.4 ExamplesThe schematic of a very simple FM radio-transmitter is shown in figure 8.6. It uses an electret microphone and transmits on a frequency between 88MHz and 108MHz.The transistor, coil L, trimmer capacitor Ct, capacitor C3 and resistors R2, R3 and R4 creates an oscillator with a frequency determined by:

In this equation CCBrepresents the capacitance between the collector and the base. The value of this capacitance depends on the voltage on the base. The higher the voltage, the lower the capacitance and vice versa. The voltage on the base is constant while there is no sound, which means the frequency of the oscillator is constant. When the microphone picks up a sound, it is passed to the base of the transistor via C1. This causes the frequency of the oscillator to change and that's w