uline ice service_manual

U-Line Corporation

www.U-LineService.com

Phone (414) 354-0300 FAX (414) 354-7905Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696

U-Line CorporationPO Box 245040

Milwaukee, WI 53224-9540

U-Line Corporation8900 North 55th StreetMilwaukee, WI 53223

SERVICE AND PARTSMANUAL

Models95 Icemaker98 Icemaker

BI15 Icemaker15R

15 Wine Captain

Combo 75 Frost FreeCombo 75A

75AD75 Wine Captain

75 Freezer75R

75RF75 Bev

Combo 29 Frost FreeCombo 29A

29AD29R

29 Wine CaptainSP18

M A D E IN

T H E U S A

R RC

Three generations of pride and quality manufacturing and design improvements are builtinto all U-Line products.

This manual contains specific instructions for servicing the entire line of U-Line Productswhich includes these models:

INTRODUCTION

Service and Parts Manual

2

95 Icemaker98 IcemakerBI15 Icemaker15R15 Wine Captain

Combo 75 Frost FreeCombo 75A75AD75R75 Wine Captain75 Freezer75RF75 Bev

Combo 29 Frost FreeCombo 29A29AD29R29 Wine CaptainSP18

This Service Manual has been written to cover product manufactured with HFC-134a.Units previously manufactured with CFC-12 will, however, be in service for many years.

SERVICING CFC-12 SYSTEMSU-Line Corporation has not approved the use of any drop in replacements for CFC-12.U-Line has also not approved the process of converting a CFC-12 system to any othertype of refrigerant.

POTENTIAL PROBLEMS WITH HFC-134AHFC-134A compressors will be received with a synthetic based ester oil charge. Thehygroscopic (water attraction) property of ester oil is many times greater than that ofthe mineral oils previously used with CFC-12. High system moisture causes the forma-tion of acids and alcohol which can damage the compressor. Systems should not be leftopen for more than fifteen (15) minutes at any time as humidity from the air will entersystem. To assure system dehydration, the system should be pulled down to 100microns and vacuum pump oil (mineral oil) must not be allowed to enter then system.

Cleanliness of the system will be extremely important. The presence of residues (chlori-nated or greasy residues, mineral oil, or impurities) can lead to capillary tube restric-tions, oil return problems and compressor damage. Flux must not be used on brazedjoints.

3Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Warranty Claims Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Guide for Screening Customer Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Refrigeration Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Normal Vapor/Compression Cycle Refrigeration . . . . . . . . . . . . . . . . . . . . . .11U-Line Frost Free Refrigeration System . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Compressor/Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Compressor Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Refrigeration System Diagnosis Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Ice Maker Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Ice Maker Operating Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Cycle Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Freeze Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Harvest-1 Cycle (Hold switch in normal position) . . . . . . . . . . . . . . . . . . .16Harvest-2 Cycle (Hold switch in switched position) . . . . . . . . . . . . . . . . . .17Water Fill Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Temperature Control Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Limit Switch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Ice Maker Diagnosis Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Frost Free Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Redesign Differentiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Typical Frost Free Airflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Disassembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Combo 75FF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Combo 29FF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2475RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Parts Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79Model 402 Ice Maker Assembly Parts Breakdown . . . . . . . . . . . . . . . . . . . . .40Parts Breakdown by Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41How to Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79Fax Parts Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

TABLE OF CONTENTS


4

Warranty StatementOn 11-1-98, U-Line Corporation modified the warranty provided with our units. We havesignificantly improved the coverage of the sealed system in years two through five of theunits life. The new warranty covers parts and labor for one year from the date of pur-chase. In years two through five, from the date of purchase, the warranty covers partsand labor for the entire sealed system. The sealed system consists of the compressor,condenser, evaporator, heat exchanger, dryer, hot gas bypass-valve and all connectingtubing.

This decision reflects our continuing commitment to strive to maintain the leadershipposition within the under counter refrigeration and ice making industry whether that bethrough design, product innovation, or enhanced consumer warranties. This decisionreinforces the confidence that U-Line has in the performance and reliability of our prod-ucts.

Our previous warranty covered parts and labor for one year from the date of purchaseplus four additional years for the compressor, part only.

The new, modified warranty applies only to units shipped after 11-1-98. All unitsshipped before 11-1-98 have the previous warranty.

PRODUCTS SHIPPED BEFORE 11-1-98 - Warranty covers parts and labor for one yearfrom the date of purchase, plus four additional years for the compressor (part only).

PRODUCTS SHIPPED AFTER 11-1-98 - Warranty covers parts and labor for one yearfrom the date of purchase and covers parts and labor for the entire sealed system forfive years.

DETERMINING SHIP DATESIn order to assure that U-Line is Y2K compliant, we have recently completed a majorcomputer system modification. The new computer system has lead to changes in theway we operate in most areas of the company. Youll soon notice that our packing listsare different, our invoices are different, our checks are different, and more. The changethat will impact you the most is the change in serial numbers.

With the new computer system, our serial number format has changed. There are somedefinite advantages that go with the new format, such as being able to tell the monthand year in which the unit was produced.

The new serial number format breaks the number down into four segments. A typicalserial number is 047413-06-0100. The first segment 04, represents the year that theunit was made. The second segment 7413, represents the shop order number. Thiscan be a three or four digit number. Order number 7413 is assigned for ModelWH95TP units. The third segment 06 represents the month that the unit was made.The forth segment 0100 represents a sequence of numbers that is used internally atU-Line Corporation.

5U-Line Corporation warrants each U-Line product to be free from defects in materialsand workmanship for a period of one year from the date of purchase; and warrants thesealed system (consisting of the compressor, the condenser, the evaporator, the hot gasbypass valve, the dryer and the connecting tubing) in each U-Line product to be free fromdefects in materials and workmanship for a period of five years from the date of pur-chase. During the initial one-year warranty period for all U-Line products U-Line shall: (1)at U-Lines option, repair any product or replace any part of a product that breaches thiswarranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced inthe United States (including Alaska and Hawaii)and Canada, U-Line shall cover the laborcosts incurred in connection with the replacement of any defective part. During yearstwo through five of the warranty period for the sealed system, U-Line shall:. (1) repairor replace any part of the sealed system that breaches this warranty; and (2) for allMarine, RV and Domestic U-Line products sold and serviced in the United States (includ-ing Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connec-tion with the replacement of any defective part of the sealed system. All other charges,including transportation charges for replacements under this warranty and labor costsnot specifically covered by this warranty, shall be borne by you. This warranty is extend-ed only to the original purchaser of the U-Line product. The Product Registration Cardincluded with the product should be promptly completed by you and mailed back toU-Line or you can register on-line at www.U-LineService.com.

The following are excluded from this limited warranty: installation charges; damagescaused by disasters or acts of God, such as fire, floods, wind and lightening; damagesincurred or resulting from shipping, improper installation, unauthorized modification, ormisuse/abuse of the product; customer education calls; food loss/spoilage; door andwater level adjustments (except during the first 90 days from the date of purchase);defrosting the product; adjusting the controls; door reversal; or cleaning the condenser.

If a product defect is discovered during the applicable warranty period, you must prompt-ly notify either the dealer from whom you purchased the product or U-Line at P.O. Box23220, Milwaukee, Wisconsin 53223 or at 414-354-0300. In no event shall suchnotification be received later than 30 days after the expiration of the applicable warrantyperiod. U-Line may require that defective parts be returned, at your expense, to U-Linesfactory in Milwaukee, Wisconsin, for inspection. Any action by you for breach of warran-ty must be commenced within one year after the expiration of the applicable warrantyperiod.

This limited warranty is in lieu of any other warranty, express or implied, including, butnot limited to any implied warranty of merchantability or fitness for a particular pur-pose; provided however, that to the extent required by law, implied warranties areincluded but do not extend beyond the duration of the express warranty first set forthabove. U-Lines sole liability and your exclusive remedy under this warranty is set forthin the initial paragraph above. U-Line shall have no liability whatsoever for any inciden-tal, consequential or special damages arising from the sale, use or installation of theproduct or from any other cause whatsoever, whether based on warranty (express orimplied) or otherwise based on contract, tort or any other theory of liability.

Some states do not allow limitations on how long an implied warranty lasts or the exclu-sion or limitation of incidental or consequential damages, so the above limitations maynot apply to you. This warranty gives you specific legal rights, and you may also haveother rights which vary from state to state.

LIMITED WARRANTY


6

This is the safety alert symbol. It is used to alert you to potential personalinjury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

!

DANGER indicates an imminently hazardous situation which, if not avoided,will result in death or serious injury.

DANGER !!

WARNING indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.

! !

CAUTION indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury.

!

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

IMPORTANT indicates installation, operation or maintenance informationwhich is important but not hazard-related.

7Do not attempt to service or repair the unit until you have read the entire procedure.Safety items throughout this manual are labeled with Warning or Caution.

SAFETY PRECAUTIONS

Risk of child entrapment. Before you throw away an old refrigerator or freezer: Take off the doors, leave shelves in place so that children may noteasily climb inside.

DANGER !!

Never attempt to repair or perform maintenance on the unituntil the electricity has been disconnected.

Altering, cutting of power cord, removal of power cord, removalof power plug, or direct wiring can cause serious injury, fireand/or loss of property and/or life and will void the warranty.

DANGER !!

Do not lift unit by door handle. Never use an ice pick or other sharp instrument to help speed up defrost-

ing. These instruments can puncture the inner lining or damage the cool-ing unit.

Failure to clean the condenser every three months can cause the unit tomalfunction. This could void the warranty.

Never install the unit behind closed doors. Be sure front grille is free ofobstruction. Obstructing free air flow can cause the unit to malfunction,and may void the warranty.


8

When submitting claims for warranty payment, please follow these guidelines.

You can use any form you would normally use to bill your customer (your own computergenerated form, Narda, USA, etc.).

The model and serial number MUST be on the claims. Claims will not be paid without amodel and serial number.

If you work on more than one unit per service call please submit a separate claim foreach unit.

We track all defects through warranty claims, so please be specific on what the repairwas. If it is a system leak, please specify where the leak was.

Please be sure the claim is legible. If the claim form cannot be read, it will be returned,unpaid.

U-Line will not cover part or labor claims for the replacement of a complete ice makerassembly. All ice maker parts are available as replacement parts and are stocked in ourinventory. Remember: we do not pay customer education calls. Door and water leveladjustments are 90 day warranties only.

If you are changing out a unit please supply the model and serial number of both units(the unit being replaced and the new unit) and the R.A. number.

If a copy of the Proof of Purchase/Install is not available at the site, the technicianshould record he following information on the Labor Invoice:

The name of the selling Dealer

The date of purchase/installation

The Order or Invoice number (if available)

The type of document the technician saw i.e. Store Receipt, Closing Papers,Sign-Off of Building Permit, Final Walk Through, etc.

At U-Line, parts and labor claims are paid separately. Included in labor would be freonand recovery charges, all other parts are handled by the parts department. We requirethat some parts be returned to us, so we may return them to our vendor. It will benoted on your packing list if we require you to return the part. If a part is to be returnedplease include a copy of the packing list and a copy of your claim. If the part was pur-chased at one of our part distributors, you must handle the part warranty with that com-pany. For labor payment please send a readable copy of your claim to U-LineCorporation, P.O. Box 245040, Milwaukee WI, 53224-9540, for warranty payment.

WARRANTY CLAIMS PROCEDURE

9U-lines warranty does not cover customer education calls. It has been reported that ashigh as 50% of all service calls performed, are customer education calls.

The following guide has been developed to help screen calls on the most common cus-tomer education issues. It can be used by persons scheduling service calls.

The unit is not cold enough!Questions to ask before scheduling a service call

Are you familiar with the factory specifications for this unit? (many factors can causethese figures to vary. Ambient temperature, application, amount of use etc.)

Model Numbers Approximate Temperatures15WC, 29WC, 75WC 60 top rack /55 middle/ 45 bottom15R, 29R, 75R 3875AD, 75, 29AD 38 fresh food, 15 freezerC75A, C75FF, C29A, C29FF 38 fresh food75 Bev 38 glass shelves, 45 wine racks

Is the door sealing properly? If the door is not sealed properly, it allows heat into theunit. U-Line's warranty is 90 days for door adjustments.

Is the condenser clean? U-Line's warranty does not cover cleaning the condenser. Is the unit behind closed doors? The unit must have free air flow to the front grille. Did you try turning the temperature control colder? Turning the control knob clock-

wise is colder. Be sure to allow 24 hrs. between temperature control adjustments. For model 29AD only. Is the defrost timer set to the time of day? When set properly,

the unit will be off, defrosting, between midnight and 3:30 a.m. For Wine Captain Units and 75 Bev. Is the light on constantly to display the wine?

If the light is on constantly, this could cause the unit to run warmer.

The ice cubes are sticking together!Questions to ask before scheduling a service call

Does the unit need to be defrosted? Is the door sealing properly? This could cause the ice cubes to stick together. Have you tried to ruffle the the ice bucket? If the ice sits without being used, it will

tend to stick together. Shaking the bucket will usually break apart the ice cubes. Ifthe ice has been sitting for a long time, we recommend dumping the bucket and mak-ing fresh ice.

CUSTOMERCOMPLAINT

CUSTOMERCOMPLAINT

GUIDE FOR SCREENING CALLS


10

No ice or not enough ice!Questions to ask before scheduling a service call

Are you aware of the factory specifications for ice production?Model # Approx. Daily Ice Rate Approx. Ice StorageCombo 75A 22.5 lbs. 13 lbs. bucketCombo 75FF 8 lbs. 13 lbs. bucketCombo 29A 22 lbs. 13 lbs. bucketCombo 29FF 8 lbs. 13 lbs. bucketModel 95 23 lbs. 12 lbs. bucketModel 98 25 lbs. 25 lbs. bucketBI15 25 lbs. 25 lbs. bucket

Is the temperature control set to the warmest setting? The unit will produce the mostice when set at the warmest setting. Let the unit run overnight.

Is the ice maker bin arm down? When the arm is up, it will not make ice. Is the door sealing properly? U-Line's warranty is 90 days for door adjustments. Does the water level need to be adjusted? U-Line's warranty is 90 days for water level

adjustments.

The unit is frosting up!Questions to ask before scheduling a service call

Are you familiar with the defrost technology of the unit?Defrost Technology Model NumbersManual Defrost Combo 75A, Combo 29A, 95, 98, 75, BI15Cycle Defrost 75R, 29R, 15R, 75WC, 29WC, 15WC, BC85DTAuto Defrost 29AD, 75AD, 75 Bev (periodic manual defrost may be needed)Frost Free Combo 75FF, Combo 29FF

Is the door sealing properly? U-Line's warranty is 90 days for door adjustments. Has the door been left open? Is the unit in an application of heavy usage? Heavy usage or high ambient tempera-

tures will cause a unit to frost up.

Water is leaking out of the back of the unit!Questions to ask before scheduling a service call

Have you checked the connection at the water solenoid valve? U-Line's warranty doesnot cover installation adjustments.

The light on my Wine Captain/75 Bev never shuts off!Questions to ask before scheduling a service call

Did you turn the on/off switch near the base of the unit? The on/off switch is for thelight operation only. When the switch is in the off position, the light will turn on onlywhen the door is open. When the switch is in the on position, the light will be on con-stantly to display the wine. To shut the unit off, turn the temperature control all theway counterclockwise.

CUSTOMERCOMPLAINT

CUSTOMERCOMPLAINT

CUSTOMERCOMPLAINT

CUSTOMERCOMPLAINT

11

Normal Vapor/Compression Cycle Refrigeration Refrigerant is pumped from the compressor to the condenser as a high pressure,

high temperature vapor.

As the refrigerant cools in the high pressure condenser, the vapor condenses to liquid.During this phase change, a great amount of heat is rejected with the help of the con-denser fan.

The liquid then flows to the dryer where it is strained and filtered.

From the dryer, the refrigerant flows through the capillary tube which meters the liquidrefrigerant to the evaporator. The pressure of the refrigerant is reduced to the evapo-rating or low side pressure.

The reduction of pressure on the liquid refrigerant causes it to boil or vaporize until itreaches saturation temperature. As the low temperature refrigerant passes throughthe evaporator coil, it continues to absorb a lot of heat, causing the boiling action tocontinue until the refrigerant is completely vaporized. It is during this phase changethat the most heat is absorbed (the cooling takes place) in the refrigerator.

The refrigerant vapor leaving the evaporator travels through the suction line to thecompressor inlet. The compressor takes the low pressure vapor and compresses it,increasing both pressure and temperature. The hot high pressure gas is pumped outthe discharge line and into the condenser. The cycle continues.

CAPILLARY TUBE

DRYER

CONDENSER

COMPRESSOR

EVAPORATOR

UL183-1

REFRIGERATION SYSTEMS


12

U-Line Frost Free Refrigeration SystemCooling Mode: Bypass solenoid valve closed Evaporator fan operating Refrigerant flows through capillary tube Normal vapor/compression cycle refrigeration

Defrost Mode: Bypass solenoid valve open Refrigerant flows through bypass system Vapor flows from condenser to evaporator without a phase change

SOLENOID VALVE

CAPILLARY TUBE

VALVE IS CLOSEDFLOW WHEN SOLENOID

DRYER

CONDENSER

COMPRESSOR

EVAPORATOR

VALVE IS OPENFLOW WHEN SOLENOID

UL183-2

13

Compressor/Electrical Specifications

Compressor PinsTo measure start winding resistance, measure across the C-S pins.To measure run winding resistance, measure across the C-R pins. These pins shouldnever measure any resistance to ground. This would indicate a shorted compressor.

SpecificationsEMI3OHER Start Winding Resistance: 28 OHMSEMI3OHER Run Winding Resistance: 8 OHMS

SD39 Start Winding Resistance: 11 OHMSSD39 Run Winding Resistance: 5 OHMS

EMI5OHER Start Winding Resistance: 12 OHMSEMI5OHER Run Winding Resistance: 4 OHMS

SD51 Start Winding Resistance: 5 OHMSSD51 Run Winding Resistance: 5 OHMS

115 VOLT Ice Maker Heater Resistance: 80 OHMS115 VOLT Water Valve Coil Resistance: 335 OHMS

C

S R

OVERLOAD PROTECTOR

STARTING RELAY

RELAY COVERUL183-3

EMI ER

Service and Parts M

anual

14

System Suction Suction Compressor Condenser Capillary Evaporator WattageCondition Pressure Line Discharge Tube

Normal Normal Slightly below Very hot Very hot Warm Cold Normalroom

temperature

Overcharge Higher than Very cold Slightly warm Hot to warm Cool Cold Higher thannormal may frost to hot normal

heavily

Undercharge Lower than Warm - near Hot Warm Warm Extremely cold Lower thannormal room near inlet - normal

temperature Outletbelow roomtemperature

Partial Somewhat Warm - near Very hot Top passes Room Extremely cold Lower thanRestriction lower than room warm - temperature near inlet - normal

normal-in temperature Lower passes (cool) or Outletvacuum cool colder below room

(near room temperaturetemperature) backing updue to liquid

Complete In deep Room Room Room Room No Lower thanRestriction vacuum temperature temperature temperature temperature refrigeration normal

(cool) (cool) (cool) (cool)

No 0 PSIG Room Cool Room Room No Lower thanGas to temperature to temperature temperature refrigeration normal

25" (cool) hot (cool) (cool)

Refrigeration System Diagnosis Guide

15

Ice Maker Operating Cycles1. FREEZE CYCLE

A. Temperature control terminals 2 and 3 are closedB. Power to the compressorC. Power to the condenser fan

2. HARVEST-1 CYCLE

A. Temperature control terminals 2 and 3 are open - 2 and 1 closeB. No power to the compressor or condenser fanC. If bin arm is down, power goes through bin arm switch to ice maker motorand mold heater. If bin arm is up, the ice maker will not harvest.

3. HARVEST-2 CYCLE

A. Ice maker ejector blades reach approximately 2:00 position and camdepresses the hold switch. Power goes through the hold switch to the icemaker motor and mold heater.

B. Ejector blades stall on ice and ice maker motor pulsates until mold heater warms and ice releases.

4. WATER FILL CYCLE

A. Ice maker ejector blades reach approximately 10:00 position and camdepresses the water fill switch.

B. Power to the water valve. Ice maker mold fills.

5. EJECT CYCLE

A. Ejector blades push ice into bucket and stop at 12:00 position.B. Temperature control terminals 2 and 3 have closed during harvest cycle.C. Next freeze cycle begins with power to the compressor and condenser fan.

ICE MAKER OPERATION


16

Cycle Schematics

HARVEST-1 CYCLE(Hold Switch In Normal Position)

SWITCHLIMIT

orange

black

black black

MOTORMAKER ICE

MOLD HEATER

WATER

SWITCH FILLC NC

MOTOR FAN

LOADOVER

black RELAYSTARTCOMP.

SWITCH OFFON

black

black

blue

black

CONTROL TEMP.

NC

black

orange

3

yellow

2

orange

SWITCH BIN

red NO

1

C

NO

brown

black

white

CSWITCH HOLD

VALVEWATER

ground

UL183-5

FREEZE CYCLE

SWITCHLIMIT

orange

black

black black

MOTORMAKER ICE

MOLD HEATER

WATER

SWITCH FILLC NC

MOTOR FAN

LOADOVER


SWITCH OFF ON

black

black

blue

black

CONTROL TEMP.

NC

black

orange

3

yellow

2

orange

SWITCH BIN

red NO

1

C

NO

brown

black

white

CSWITCH HOLD

VALVEWATER

ground

UL183-4

17

Cycle Schematics

WATER FILL CYCLE

SWITCHLIMIT

orange

black

black black

MOTORMAKER ICE

MOLD HEATER

WATER

SWITCH FILLC NC

MOTOR FAN

LOADOVER


SWITCH OFF ON

black

black

blue

black

CONTROL TEMP.

NC

black

orange

3

yellow

2

orange

SWITCH BIN

red NO

1

C

NO

brown

black

white

CSWITCH HOLD

VALVEWATER

ground

UL183-7

HARVEST-2 CYCLE(Hold Switch In Switched Position)

SWITCHLIMIT

orange

black

black black

MOTORMAKER ICE

MOLD HEATER

WATER

SWITCH FILLC NC

MOTOR FAN

LOADOVER


SWITCH OFF ON

black

black

blue

black

CONTROL TEMP.

NC

black

orange

3

yellow

2

orange

SWITCH BIN

red NO

1

C

NO

brown

black

white

CSWITCH HOLD

VALVEWATER

ground

UL183-6


18

Temperature Control SpecificationsDouble Throw Ice Maker Thermostat Numbers4548, AR-19-12, 2636, 2690, 2691, 2717

These temperature controls are double throw, single pole controls. The sensing tube isinserted into the ice maker mold and senses mold temperature. After ice is sensed inthe mold, the 2-3 contacts open (stopping the compressor) and the 2-1 contacts areclosed (starting the ice maker motor). The 2-3 contacts close (2-1 contacts open)before the end of the ice harvest cycle. This prepares the control for the next cycle.

2 21

3

1

3

FREEZE POSITION ICE HARVEST POSITION

CYCLECLOSEDCIRCUIT

OPENCIRCUIT

FREEZE 2 - 1 2 - 3

HARVEST 2 - 3 2 - 1

183-9

YELLOW WIRECONNECTION

RED WIRECONNECTION

BLUE/BLACK WIRECONNECTIONICE MAKER CONTROL

2 1

3

183-8

19

Limit Switch Specifications

Normally Closed Bi-metal SwitchOpen Temperature: 104 Degrees FClose Temperature: 83 Degrees F

The function of this switch is to open in the event of an overheating condition. Thisbi-metal thermostat is normally closed and does not initiate the ice harvest cycle.The ice harvest cycle is initiated by a double throw, single pole switch located remote-ly from the ice maker assembly.

28.12

3.00

183-10


20

Ice Maker Diagnosis Flow Chart

DOES THE UNIT REFRIGERATE?

Sealed System LeakElectrical FailureCompressor FailureFan Motor FailureDefrost System Failure

Low VoltageVoltage DropWiring

Temperature Control FailureWater AdjustmentBin Switch Failure

NO

NO

EVERYW

HERE

INTERMITTENT

AT 3:00

YE

SN

OA

T 1

2:00

DOES THE UNIT HARVEST ICEIF THE EJECTOR BLADES AREMOVED BY HAND OR WITH A

WRENCH ?

WHERE DO THE EJECTOR BLADES

STOP?

Mold Heater Failure

Solenoid Valve Failure

Ice Motor FailureHold Switch FailureLimit Switch FailureBinding Cam/Ejector

Water Switch Failure

IS THERE VOLTAGE AT THE SOLENOID VALVE TERMINALS

DURING HARVEST?

UL183-11

YES

YES

21

Redesign DifferentiationThrough our continuous efforts to improve our product line, U-Line Corporation hasmade some changes to the design of Models Combo 29FF and Combo 75FF.

The objective of this section is to assist the service technician in differentiating betweenthe previous design product and the new redesign.

The redesign involves a new compressor, evaporator and heat exchanger, condenser fanmotor, evaporator fan motor, drain trough, timer and power cord.

To address service problems which may exist in earlier designs, we developed a Field FixKit. It involves replacing the compressor, dryer, and hot gas valve. It also includesmounting a sheet of insulation to the back panel. Before installing the new compressor,hot gas bypass valve, and dryer, it is imperative that the entire refrigeration system beblown out with nitrogen to remove any excess oil. This kit is to be installed in units withR-134a only starting with serial number 7CF300000 or 2CF300000. Installationinstructions are included in each kit ordered.

The new compressor, a Matsushita Model SD39C replaces the previous compressor, anEmbraco EMI 50 HER.

Both the previous design and the new redesign are detailed in this manual. New designunits and previous design units can be differentiated by the serial numbers. All serialnumbers for the new redesigned units start with a number higher than 600000.(Example: 2CF600001 is a new redesigned Combo 29FF.) Previous design units haveserial numbers which start with 300001, 400001, or 500001. (Example:7CF400001 is a previous design Combo 75FF.)

Pages 45-46 show the parts breakdown for the previous design of the Combo29FF. The parts replaced with the kit are denoted. The wiring diagram for thismodel is on page 36.

Pages 41-42 show the parts breakdown for the previous design of the Combo75FF. The parts replaced with the kit are denoted. The wiring diagram for thismodel is on page 36.

Pages 47-48 show the parts breakdown for the new, redesign of the Combo29FF. The wiring diagram for this model is on page 37. The information for thehybrid redesign of the Combo 29FF can be found in the chelon Service Manual.

Pages 43-44 show the parts breakdown for the new, redesign of the Combo75FF. The wiring diagram for this model is on page 37.

FROST FREE UNITS


22

Typical Frost Free Airflow Configuration

Air Flow In AtEvaporator Blade

Air Flow Out AtEvaporator Outlet

Air PassesThrough Fin/TubeEvaporator

Condensate Drains Down Trough Under Evaporator,Into Drain Cup, And Into Condensate Pan ThroughDrain Hose. The Drain Trough Is Warmed DuringDefrost By Contact with Evaporator Fins.

UL183-12

23

Disassembly ProceduresModel Combo C075FF1. Disconnect from power source.2. Disconnect ice maker wires in back of unit.3. Remove screws (6) from freezer housing.4. Slide out freezer housing with ice maker unit

attached.5. Remove screws (4) from evaporator cover.6. Slide evaporator cover out of clips (2).

To remove fan blade/motor:1. Disconnect fan wires in the back of unit.2. Remove fan blade by sliding off fan motor

shaft.3. Remove screws (2) from fan motor mount-

ing bracket.4. Remove mounting nuts (2) from fan motor

studs.

To remove evaporator:1. Disconnect copper tubing. Be sure to

reclaim, recycle or recover refrigerant.2. Remove screw from evaporator clip (2).3. Slide out evaporator.

HOUSINGFREEZER

SCREWS (2)

SCREWS (2)

UNITICE MAKER

UL183-13

COVEREVAPORATOR

SCREWS (4)

CLIP

UL183-14

EVAPORATOR

SCREWS (2)

CLIP (2)EVAPORATOR

AND BLADEFAN MOTOR

NUTS (2)FAN MOTOR

UL183-15


24

Model Combo C029FF1. Disconnect from power source.2. Disconnect ice maker wires in back of unit.3. Remove screws (3) from freezer housing.4. Slide out freezer housing with ice maker unit

attached.5. Remove screws (4) from evaporator cover.6. Slide evaporator cover out of clips (2).

To remove fan blade/motor:1. Disconnect fan wires in the back of unit.2. Remove fan blade by sliding off fan motor

shaft.3. Remove screws (2) from fan motor mount-

ing bracket.4. Remove mounting nuts (2) from fan motor

studs.

To remove evaporator:1. Disconnect copper tubing. Be sure to

reclaim, recycle or recover refrigerant.2. Remove screw from evaporator clip (2).3. Slide out evaporator.

HOUSINGFREEZER

UNITICE MAKER

SCREWS (2)

UL183-16

COVEREVAPORATOR

CLIP

SCREWS (4)

UL183-17

NUTS (2)FAN MOTOR

CLIP (2)EVAPORATOR

EVAPORATOR

SCREWS (2)

AND BLADEFAN MOTOR

UL183-18

25

Model Combo 75RF1. Disconnect from power source.2. Remove freezer door.3. Slide out mullion.4. Remove screws.

To remove fan blade/motor:1. Disconnect fan wires in the back of unit.2. Remove fan blade by sliding off motor shaft.3. Remove screws (2) from mounting bracket.4. Remove nuts from fan motor studs.

To remove evaporator:1. Recover all refrigerant.2. Disconnect copper tubing.3. Remove mounting screws (4) from

evaporator.4. Slide out evaporator.

EVAPORATOR COVER

MULLION

UL183-19

EVAPORATOR

FAN & MOTOR

UL183-20


26

NEVER attempt to repair or perform maintenance on the unit until the mainelectrical power has been disconnected.

1. Will not eject ice (water frozen)Cause Remedy

Control setting too cold Adjust control warmer (counterclockwise) Control defective (1-2 contacts open) Replace control Bin switch defective Replace bin switch Limit switch defective (open) Replace limit switch Ice maker assembly motor stalled Replace motor Broken wire in ice maker circuit Repair or replace wiring Water soaked cabinet insulation Replace foamed cabinet assembly Dirty condenser Clean condenser

2. Will not fill with waterCause Remedy

Water supply valve closed Open water supply valve Water switch defective (open) Replace water switch Solenoid valve defective Replace solenoid valve Fill tube outlet frozen Replace solenoid valve and defrost fill tube Broken wire in water fill circuit Repair or replace wiring

3. Will not stop making iceCause Remedy

Bin switch defective (closed) Replace bin switch Bin arm binding Lubricate bin arm pivot points or loosen

bin arm lever screw

4. Water will not stop fillingCause Remedy

Water switch defective (closed) Replace water switch Solenoid valve defective Replace solenoid valve Stalled ice maker motor Replace motor Temperature control defective. Replace temperature control

Ice maker is in continuous harvestcycle (contacts 1-2 closed)

5. Ejector blades will not stop turningCause Remedy

Control defective (1-2 contacts will Replace controlnot open)

Hold switch defective Replace hold switch Defective wiring Repair or replace wiring Short in mold heater Replace heater

DANGER !!

TROUBLESHOOTING

27

6. Low ice productionCause Remedy

Control set too cold Adjust control warmer (counterclockwise) Fan motor stalled Replace fan motor Ice cubes too large Lower water fill adjustment Dirty condenser Clean condenser Bypass valve stuck open Replace bypass valve

7. Not freezing (compressor and fan motors operating)Cause Remedy

Little or no frost pattern on evaporator Check for sealed system leak or restriction Bypass valve stuck open Replace bypass valve

8. Not freezing (compressor not operating - fans operating)Cause Remedy

Relay defective Replace relay Overload defective (open) Replace overload Compressor defective Replace compressor

9. Not freezing (compressor and fans not operating)Cause Remedy

On-Off switch defective (open) Replace On-Off switch Hold switch defective (open) Replace hold switch Control defective (2-3 contacts open) Replace control Broken wire in freeze circuit Repair or replace wiring Power cord not plugged in Plug in power cord On-Off switch in off position Put switch in on position Ejector blades not in the freeze Manually advance ejector blades to the

position (12:00) 12:00 position (test ice maker andlimit switch)

10. Compressor overheatingCause Remedy

Condenser air flow restricted Remove restriction (clean condenser and grille)

Condenser fan blade obstructed Remove blade restriction Condenser fan motor stalled Replace fan motor Defective compressor Replace compressor

11. Compressor will not stop operatingCause Remedy

Control set too cold Adjust control warmer (counterclockwise) Control defective (2-3 contacts will not Replace control

open) Control sensing bulb not sensing Fully insert bulb into ice maker tube,

mold temperature routing bulb away from compressordischarge tube

Evaporator fan stalled Remove obstruction or replace motor

12. Water leak (under unit)Cause Remedy

Water supply line leaking at solenoid Tighten or replace fittingvalve inlet

Water line leaking at solenoid valve outlet Replace water line and fitting


28

Water line leaking at fill tube Tighten clamp or fill tube replace fill tube assembly

Defrost drain line not in drain pan Position drain line in drain pan Crack in water line Replace water line

13. Water leak (inside unit)Cause Remedy

Ice maker assembly fill cup obstructed Remove obstruction. Fill ice cup and fill tube out of alignment Align fill tube and fill cup Water level too high Adjust water level Defrost drain plugged Ice in drain trough (refer to #16)

14. Excessive frost build-upCause Remedy

Door gasket not sealing properly Adjust door hinges or replace door gasket Door out of alignment Adjust door hinges Water soaked cabinet insulation Replace foamed cabinet assembly

(factory repair only) Light stays on when door is closed Repair or adjust light bracket

15. NoisyCause Remedy

Copper refrigeration tube touching cabinet Carefully adjust tubing Fan blade touching shroud Adjust fan mounting or shroud Fan blade obstruction (wiring, foam Remove obstruction

insulation, packaging material)

16. Ice build-up in drain trough or drainage problem (see page 20)Cause Remedy

Obstructed drain cup or tube Clear obstruction Evaporator not touching drain trough Reposition evaporator to contact drain

trough along entire length Kinked drain tube Reroute drain tube Drain trough spout and drain cup Align drain trough and drain cup

not aligned

17. Unit will not defrostCause Remedy

Bypass valve bent (will not operate) Align bypass valve and coil assembly Bypass coil defective Replace bypass valve Defrost timer defective Replace defrost timer Bypass valve defective Replace bypass valve

18. Fresh food temperature too coldCause Remedy

Ice bucket not fully inserted Push ice bucket in place Temperature control set too cold Adjust control to warmer setting

(counterclockwise) Air leak at evaporator cover Seal cover with RTV

REPLACEMENT PARTS: Use only genuine U-Line replacement parts. The use of nonU-Line parts can reduce ice rate, cause water to overflow from ice maker mold, dam-age the unit, and may void the warranty.

29

EMBRACO

MATSUSHITA

ASSEMBLY

POWER CORD

KGS

BLUE

GREEN

WHITE

BLUE

CAPACITOR

GREEN

BLUE

BLUE

WHITE

COMPRESSOR

8

RELAY

3

OVERLOAD

BLUE

RELAY

OVERLOAD 2

15WC, 29WC, 75WC, 220 VOLT WIRING DIAGRAM

CO

MPR

ESSO

R

15 & 75 ONLY

GREEN GRD.

WHITE - NEUTRAL

GREEN GRD.

BLACK - HOT

OVERLOAD

BLACK

LAM

P

BLACK

RELAY

BLUE

FAN

WHITE

BLACK

P/N B41885

ROCKER SWITCH

DOOR LAMP SWITCH

CONTROL

B42061.eps

BLACK

POWER CORD ASSEMBLY

GREENGROUND

BLACK-HOT(SMOOTH)

BLACK-NEUTRAL(RIBBED)

ROCKERSWITCH

BLACK

RED

YELLOW

BROWN

WHITE

WATERVALVE

BLACK

BLACK

3 RPMMOTOR

LIMITSW

MOLD HEATER

C

NO NC

BINSW

NC NO

WATERSW

CCAM

NCNO

C

HOLDSW

ORANGE

RED

BLACK BLACK

BLACK

ORANGE ORANGE

YELLOW

WHITEBROWN

ICEMAKER ASSEMBLY

RED

YELLOW

BROWN

WHITE

BLACK

BLUE

BROWN

WHITE

TEMPERATURECONTROL

BLACK

CONDFAN

123

NEUTRAL(BLUE)

HOT(BLACK)

HOT(BLACK)

RELAY

EMBRACOCOMPRESSOR

OVERLOAD

NEUTRAL(BLUE)

GREENGROUND

95, 98 AND SP18 220 VOLT WIRING DIAGRAM

WIRING DIAGRAMS


30

YELLOW

BROWN

WHITE

WHITE

BLACK

RED

WHITE

LOADOVER RELAY

COMPRESSOR

BLACK

GREEN

GREEN

BLACK

SWITCHDOOR

CONDENSER

CONTROLTEMPERATURE

FAN

WHITE

BLACK

BLACK

ON/OFF SWITCH

BLACK

BLACK

BLACK

BLU

E

LAMP

BLACK WHITE

SOLENOIDWATER

WHITE

2

1

3 BLACK

ICEMAKER ASSEMBLY

SWLIMIT

BLACK

WHITE (RIBBED)

KGS

BLACK BLACK

MOLD HEATER

MOTOR3 RPM

RED

BROWN

OR

ANG

EBL

ACK

NO

YELL

OW

SWHOLD

CAMNC

C

WHITE

BLACK

RED

YELLOW

ORANGE

BLAC

KO

RAN

GE

BLACK

BROWN

SWWATER

C

NC NO

SWBIN

NC

C

NO

COMBO 75A 220 VOLT WIRING DIAGRAM (WITH BASE MOUNTED CONTROL)

P/N 41886

NO

ICEMAKER ASSEMBLY

BLACK

LOADOVER

COMPRESSOR

GREEN

BLACK

BLACK WHITE

GREEN

ON/OFF SWITCH

RELAY

CONDENSER

BLACK

WHITE

FAN

BLACK

BLU

E

BLACK

SWITCHDOOR

BLACK WHITE

LAMP

1BLACK

CONTROLTEMPERATURE 2

BLACK

3

SOLENOIDWATER

BLAC

K

YELL

OW

BLACK

BROWN

WHITE

WHITE

YELLOW

BLACK

RED

YELLOW

WHITE

BROWN

RED

BLACK

BLAC

K

EMBRACO

WHITE (RIBBED)

BLACK

MOLD HEATER

SWLIMIT BLACK

GREEN

WHITE

MATSUSHITA

BLACK

SWBIN

BROWN

BLACK

MOTOR

3 RPM

OR

ANG

E

OR

ANG

E

ORANGE

C

CAMNC

SWHOLD

C SWWATER

NONC

C

RED

NO NC

BLUE

CAPACITOR

BLUE

GREEN

BLUE

WHITE

RELAY

COMPRESSOR

OVERLOAD

BLACK

RELAY

OVERLOAD

8

23

COMBO 75A WIRING DIAGRAM

P/N A41881

31

MATSUSHITA

EMBRACO

WHITE

WHITE

WHITE

WHITE

WHITE

BLACK

BLUE

BLUE

GREEN

WHITE

BLUE

GREEN

CAPACITOR

BLUE

WHITE

BLUE

COMPRESSOR

8

RELAY

3

OVERLOAD

BLUE

RELAY

OVERLOAD 2

ASSEMBLY POWER CORD

Com

pres

sor

JunctionMolded WHITE (NEUTRAL)

GREEN

BLACK (HOT)

RELAY

OVERLOAD

Fan

Control

BLACK

BLACK

MOTOR

TIMER

DEFROST

43 2 1

P/N A41857

MODEL 29AD WIRING DIAGRAM WITH MALLORY DEFROST TIMER


32

B42056.eps

FAN

CONTROL

BLACK

POWER CORD ASSEMBLY

GREENGROUND

BLACK-HOTSMOOTH


WHITE

BLUE

(HOT)BLUE

RELAY

EMBRACOCOMPRESSOR

75F

OVERLOAD

(NEUTRAL)WHITE

(NEUTRAL)WHITE

DANFOSSCOMPRESSOR

75F

CAPACITOR

RELAY

OVERLOAD

1

2 3

(HOT)BLUE

GREEN GROUND

(HOT)BLUE

(NEUTRAL)WHITE

GREEN GROUND

(HOT)BLUE

(NEUTRAL)WHITE

OVERLOAD

RELAY

29REMBRACO

COMPRESSOR

CAPACITOR

29R AND 75F WIRING DIAGRAM

D42062.eps

BLACK

POWER CORD ASSEMBLY

GREENGROUND

BLACK-HOT(SMOOTH)


ROCKERSWITCH

BLACK

RED

YELLOW

BROWN

WHITE

WATERVALVE

BLACK

BLACK

3 RPMMOTOR

LIMITSW

MOLD HEATER

C

NO NC

BINSW

NC NO

WATERSW

CCAM

NCNO

C

HOLDSW

ORANGE

RED

BLACK BLACK

BLACK

ORANGE ORANGE

YELLOW

WHITEBROWN

ICEMAKER ASSEMBLY

RED

YELLOW

BROWN

WHITE

BLACK

BLUE

BROWN

WHITE

ICEMAKERCONTROL

BLACK

CONDFAN

123

NEUTRAL(BLUE)

HOT(BLACK)

HOT(BLACK)

RELAY

EMBRACOCOMPRESSOR

OVERLOAD

NEUTRAL(BLUE)

NEUTRAL(WHITE)

DANFOSSCOMPRESSOR

CAPACITOR

RELAY

OVERLOAD

1

2 3

HOT(BLACK)

GREENGROUND

GREENGROUND

95, 98 AND SP18 WIRING DIAGRAM

33

BLAC

K

BLAC

K

EMBRACO

GREEN

BLUE

WHITE

MATSUSHITA

BLUE

CAPACITOR

WHITE

BLUE

GREEN

BLUE

COMPRESSOR

OVERLOAD

RELAY

BLUE

RELAY

OVERLOAD

8

3 2

75AD WIRING DIAGRAM

ASSEMBLY POWER CORD

SOLENOIDBYPASS

GREEN

BLACK

WHITE

(RIBBED) WHITE

BLACK

WHITE

RELAY

GREEN

BLAC

K

LAMP

SWITCHDOOR

BLAC

K

WHITE

WHITE

OVERLOAD

BLUE

CONTROLTEMP

CO

MPR

ESSO

R

BROWN

WHITE

WHITE

MOTOR

TIMERDEFROST

312 4

BLACK

FAN

CONDENSER

BLACK

P/N B41870

A42058.eps

LAM

P

FAN

CONTROL

BLACK

BLACK

POWER CORD ASSEMBLY

GREENGROUND

BLACK-HOTSMOOTH


BLACK

DOORLAMP

SWITCHBLUE

HOT(BLUE)

RELAYEMBRACO

COMPRESSOR

OVERLOAD

NEUTRAL(WHITE)

NEUTRAL(WHITE)

DANFOSSCOMPRESSOR

CAPACITOR

RELAY

OVERLOAD

1

2 3

HOT(BLUE)

GREENGROUND

HOT(BLUE)

NEUTRAL(WHITE)

GREENGROUND

75R WIRING DIAGRAM


34

WHITE (RIBBED)

ICEMAKER ASSEMBLY

BLACK

LOADOVER

COMPRESSOR

BLACK

GREEN

BLACK

WHITE

GREEN

BLACK

ON/OFF SWITCH

CONDENSER

FAN

BLACK

BLACK

WHITE

RELAY

BLU

E

CONTROLTEMPERATURE

1

2 3

WATER PUMP

1861

SOLENOIDWATER

WHITE BLACK

YELL

OW

YELLOW

BLACK

BROWN

WHITE

RED

BLACK

YELLOW

WHITE

BROWN

BLACK

RED

BLAC

K

BLACK

BLACK

MOLD HEATER

SWLIMIT

EMBRACO

GREEN

BLACK

MATSUSHITA

SWBIN

OR

ANG

E

BROWN

C

C

MOTOR

3 RPM

OR

ANG

EBL

ACK

ORANGE

NO

C

SWHOLD

NC

NO

SW

WATER

CAM

NC

BLACK

NO

RED

NC

BLUE

WHITE

BLUE

GREEN

BLUE

CAPACITOR

WHITE

RELAY

COMPRESSOR

OVERLOAD

BLACK

OVERLOAD

RELAY

8

3 2

WATER TANK MODELS WIRING DIAGRAM

P/N B41349

B42057.eps

LAM

P

FAN

CONTROL

BLACK

BLACK

POWER CORD ASSEMBLY

GREENGROUND

BLACK-HOTSMOOTH


WHITE

BLACK

DOORLAMP

SWITCH

WHITE

BLUE

(NEUTRAL)WHITE

DANFOSSCOMPRESSOR

CAPACITOR

RELAY

OVERLOAD

1

2 3

(HOT)BLUE

(HOT)BLUE

(NEUTRAL)WHITE

GREENGROUND

(HOT)BLUE

(NEUTRAL)WHITE

OVERLOAD

RELAY

EMBRACOCOMPRESSOR

CAPACITOR

15R WIRING DIAGRAM

35

WHITE

BLACK

WHITE

CONDENSER

FAN

SOLENOID

BYPASS

CONTROL

TEMP

BLAC

K

BLAC

K

BLACK

LAMP

SWITCH

DOOR

BLAC

K

WHITE

EVAPORATOR

BROWN

BLACK

GREEN

WHITE

FAN

CO

MPR

ESSO

R

OVERLOAD

BLUE

RELAY

GREEN

WHITE

WHITE

BLACK

TIMER

DEFROST

P/N 41926

(RIBBED)

WHITE

GREEN

HOT

NEUTRAL

BLACK

BLAC

K

12

MOTOR

4 3

PURPLE

75RF WIRING DIAGRAM

BLACK


36

ICEMAKER ASSEMBLY

NO

COMBO 75FF (Previous Design; starting S/N 7CF300000,7CF400000 or 7CF500000) WIRING DIAGRAM

BLACKO

RAN

GE

BLACK MOTOR

GREEN

BLACK

SOLENOIDBYPASS

WHITEWHITE (RIBBED)

BLACK

BLACK

BLAC

K

ON/OFF SWITCH

COMPRESSOR

GREEN

WHITE

BLACK

LOADOVER

BLACK

CONDENSERFAN

3

RELAY

4 21

FANEVAP

PURPLE

BLACKBLACK

PURPLE

CONTROLTEMPERATURE

BLACK

SWITCHDOOR

2

BLACKBLACK

1

3

WHITE

LAMP

SOLENOIDWATER

BLU

E

WHITE

BLAC

K

YELL

OW

YELLOW

WHITE

BLACK

WHITE

BROWN

BLU

E

BLACK

RED

BLACK

BROWN

WHITE

YELLOW

RED

GREENBLACK SWLIMIT

EMBRACO

MATSUSHITA

BLACK

OR

ANG

E

MOLD HEATER

MOTOR

3 RPM

BLAC

K

NC CAM SWHOLD

C

C

BROWN

NONC

SWWATER

NC

ORANGE

NO

SWBIN

C

RED

BLACK

WHITE

BLUE

CAPACITOR

BLUE

BLUE

GREEN

WHITE

COMPRESSOR

3

BLACK

OVERLOAD

RELAY

OVERLOAD

RELAY

2

8

P/N A41882

WHITE (RIBBED)

MOTOR

BLACK

SOLENOIDBYPASS

TIMER

BLACK

WHITE

EVAPORATOR

FAN

PURPLE

BLACK

BLACK

COMPRESSOR

CONDENSER

FAN

WHITE

RELAYOVERLOAD

BLACK WHITE

BLACK

PURPLE

CONTROLTEMPERATURE

BLACK

GREEN

3

1

2

SOLENOIDWATER

3 4 1 2

BLACK

WHITE

BLUE BLACKBLACK

BROWN

WHITE

BROWN

WHITE

RED

YELLOW YELLOW

RED

SWLIMIT

EMBRACO

BLACK

ICEMAKER ASSEMBLY

GREEN

P/N B41858

YELL

OW

C

MOLD HEATER

MOTOR3 RPM

NC

SWWATER

OR

ANG

E

BLACK

BLAC

K

NC

NOCAM

SWHOLD

OR

ANG

EBL

ACK

BLACK

BLACKC

NO

RED

ORANGE SWBIN

C

BROWN

NO NC

BLUE

GREEN

BLUE

WHITE

CAPACITOR

GREEN

MATSUSHITA

WHITE

BLACKBLUE

RELAY

OVERLOAD

RELAY

OVERLOAD

BLACK

3 2

COMPRESSOR

8

COMBO 29FF (Previous Design; starting S/N 2CF300000,2CF400000 or 2CF500000) WIRING DIAGRAM

37

WHITE (RIBBED)

SOLENOIDBYPASS

GREEN

BLACK

FAN

BLACK

EVAP

BLACK

COMPRESSOR

ON/OFF SWITCH

CONDENSERFAN

BLACK

LOADOVER

BLACK

GREEN

BLACKBLACK

RELAY

WHITE

BLACK

PURPLE

CONTROLTEMPERATURE

BLACK

2 3

SWITCHDOOR

ORANGE STRIPE BLACK W/

1

SOLENOIDWATER

23 4 1BLACK

BLACK

BLU

E

PURPLE

BLACK

WHITE

BLACK

WHITE

LAMP

BLUE

WHITEWHITE

WHITE

BROWN BROWN

RED

YELLOW YELLOW

RED

BLACK

EMBRACOBLACKBLACK SWLIMIT

ICEMAKER ASSEMBLY

BLACK

YELL

OW BROWN

MOLD HEATER

MOTOR

3 RPM

OR

ANG

EBL

ACK

NC

NO

C

SWHOLD

CAM

OR

ANG

EBL

ACK

BLACK SWWATER

NC NO

C

RED

ORANGE SWBIN

C

NO NC

CAPACITOR

BLUE

WHITE

GREEN

MATSUSHITA

GREEN

BLACK

BLUE

WHITE

BLACK

RELAY

OVERLOAD

COMPRESSOR

P/N 41968

COMBO 75FF (New Design; starting S/N 7CF600000) WIRING DIAGRAM

BLACK

WHITE (RIBBED)

BLACK

SOLENOIDBYPASS

TIMER

BLACK GREEN

WHITE

GREEN

BLACK

ON/OFF SWITCH

OVERLOAD

COMPRESSOR

WH

ITE

WHITE

RELAY

PURPLE

BLACK

FAN

BLACK

2 3

1

BLACK

BLACK

SOLENOIDWATER

13 4 2

BLACK

PURPLE

FAN

WHITE

WHITE

BLUE

WHITEWHITE

BROWN BROWN

BLACK

REDYELLOW

BLACK

REDYELLOW

SWLIMIT BLACKBLACK

POWER CORD

ICEMAKER ASSEMBLY

P/N 41969

YELL

OW BROWN

MOTOR3 RPM

MOLD HEATER

OR

ANG

EBL

ACK

NO

C

NC

SWHOLD

CAM

OR

ANG

EBL

ACK

BLACK

NONC

C SWWATER

RED

ORANGE SWBIN

C

NCNO

BLUE

WHITE

EMBRACO

MATSUSHITA

CAPACITOR

BLACK

BLUE

WHITE

COMBO 29FF (New Design; starting S/N 2CF600000) WIRING DIAGRAM

OVERLOAD

RELAY

BLACK

COMPRESSOR


38

ASSEMBLY POWER CORD

OVERLOAD

OVERLOAD

CAPACITOR

GREEN GROUND15WC & 75WC ONLY

GREEN GROUND15WC & 75WC ONLY

RELAY

RELAY

NEUTRAL(WHITE)

NEUTRAL(WHITE)

HOT(BLUE)

HOT(BLUE)

DANFOSSCOMPRESSOR

EMBRACOCOMPRESSOR

15WC, 29WC, 75WC, 75 BEV WIRING DIAGRAM

WHITE - NEUTRAL

NEUTRAL(WHITE)

WHITE

Fan

BLUE

Control

BLACK

BLACK

BLACKWHITE

HOT(BLUE)

BLACK - HOT

GREEN GRD.BLACK

BLACK

RockerSwitch

Lamp

P/N B41860_E

DoorLampSwitch

39

220 Volt Part Conversion ListAll parts listed in the SERVICE and PARTS MANUAL are 110/115 volt. This documentis a conversion list for the applicable 220 volt part.

These 220 volt parts are used on the 95, 98 and BI15 Ice makers, the PBCM 95/98Tank Model Ice Makers, Combo 29A, Combo 75A plus the 75WC, 29WC, and 15WCWine Captains.

110V PART NO. DESCRIPTION 220V PART NO.

5263 Fan Motor (all models) 5195627973 I.M. Motor (Ice Makers)* 628109625843-S Mold Heater* 626069-S628123-S Mold Heater Assy* 618402 Ice Maker Assy* 6192552A Water Valve* 2555A31317 Lamp Bulb 313185402-S Compressor (Ice Makers)* 5404-S5411 Overload** 54155412 Relay** 5416150 Faceplate Assy* 6505400-S Compressor (Wine Captains)** 5403-S5414 Relay 54185413 Overload* 5417

* Parts used on models 95/98 Ice Makers, and BI15 Ice Makers, the PBCM 95/98 Tank Model Ice Makers, Combo 29A, and Combo 75A.

** Parts used on the 15WC, 29WC and 75WC Wine Captains.

Replacement Parts For Stainless Steel Doors

* The bottom hinge for these models is only available in black.

Model75RF 75R 75WC CO75FF BI 15 15R 15WC 75 BevPart No. Description

1847-1-SS Hinge Plate Top X X X1847-2-SS Hinge Plate Bottom X X X1848A-S-SS Top Hinge X X X11624-1-S-BLK* Bottom Hinge X X X42021 Handle X X42019 Handle X X X41995-1 Handle X41995-3 Handle X242-1-SS Top Hinge Right X X X X X245-1-SS Bottom Hinge Right X X X X X


40

MODEL 402 ICE MAKER

402ICEMAKER

20

18

17

15

3219

16

14

2712

13

21

26

25 21

2930

10

11

7

9

4

5

28

8

2422

6

31

23

3

2

1

402ICEMAKER

Use only genuine U-Line replacement parts. U-Line ice maker parts are notthe same as standard FSP Whirlpool parts. Using non U-Line parts canreduce ice rate, cause water to overflow from ice maker mold, damage theunit, and may void the warranty.

41

*Parts included in the 150 faceplate assembly.

Item Description White Black Stainless- Ice Maker Assembly 402 402 402- Faceplate Assembly 150 150 1501 Cover 627000 627000 6270002 Gear 628210* 628210* 628210*3 Motor 627973* 627973* 627973*4 Spring 627163* 627163* 627163*5 Valve Switch Plate 625836* 625836* 625836*6 Switch Spacer 625834* 625834* 625834*7 Cam 627302* 627302* 627302*8 Insulator 627680* 627680* 627680*9 Hold Switch 2506* 2506* 2506*10 Limit Switch 2579 2579 257911 Valve Switch 2506* 2506* 2506*12 Support Housing 625827 625827 62582713 Bin Arm 2603 2603 260314 Bin Arm Spring 627526 627526 62752615 Ejector 627375 627375 62737516 Mold Heater 625843-S 625843-S 625843-S17 Stripper 31400 31400 3140018 Stripper Screw 489128De 489128Description 489128 Part No.19 Mold & Heater Assembly 628123-S 628123-S 628123-S20 Water Cup 544304 544304 54430421 Spring & Housing Screw 488372* 488372* 488372*22 Gear Screw 488957* 488957* 488957*23 Face Plate 11641* 11641* 11641*24 Plate Screw 41375 41375 4137525 Long SW Screw 488361* 488361* 488361*26 Short SW Screw 488362* 488362* 488362*27 Bin SW Screw 488360 488360 48836028 Clamp 625829 625829 62582929 Arm Lever 625830 625830 62583030 Arm Lever Screw 627199 627199 62719931 Motor Screw 488622* 488622* 488622*32 Bin Switch 2506 2506 2506

220V Motor 628109 628109 628109220V Mold Heater 626069-S 626069-S 626069-S220V Mold & Heater Assembly 618 618 618220V Faceplate Assembly 650 650 650220V Ice Maker Assembly 619 619 619

MODEL 402 ICE MAKER


42

COMBO 75FF (1 of 2)Previous Design Starting With Serial Numbers

7CF300000, 7CF400000 or 7CF500000

For Item #10, see Model 402 Ice Maker (page 40) for separate breakdown.

Item Description Part No.

1 Handle 31489-4*2 Door Gasket 31493-4*3 Door Shelf Retainers (3) 31521-14 Shelf Retainer Rivet (6) 418245 Door Switch 19166 Door Assy 75-DOOR*7 Hinge, Top, 3 Hole 11697-ST*

Hinge, Top, 4 Hole 11849-ST*8 Pivot Screw, Top 41785-SS*9 Dr Switch Brkt 1171210 Ice Maker Assy 40211 Ice Bucket 3150112 Control 271713 Control Knob 4149214 Switch On-Off 205315 Lamp Bulb 3131716 Ice Bin Door 31523-S


17 Glass Shelf (1) 31427-118 Glass Half Shelf (1) 3143519 Grille 11664*20 Glass Short Shelf (2) 31423-121 Trim Strip, Front Long (2) 31443-422 Trim Strip, Front Short (2) 31443-223 **Timer 2632-124 Fan Motor, Evaporator 5299-125 Fan Blade, Evaporator 3165626 Hinge, Bottom, 3 Hole 11697-SB*

Hinge, Bottom, 4 Hole 11849-SB*27 Pivot Screw, Bottom 41747-SS*28 Freezer Housing 11537-S29 Ice Bin Door Hinge 3146330 Evaporator & Heat Exchange 2631-S7531 Light Cover 3131432 Lamp Holder NLA

*Please indicate color.**Replaces P/N 2595 or 2632 through installation of kit.

1

11

2627

9

43

872

1923513

1214

617

1531

32

22

7

1821

20

28

2524

16

10

29

COMBO75FFa

43

COMBO 75FF (2 of 2)Previous Design Starting With Serial Numbers

7CF300000, 7CF400000 or 7CF500000


1 Water Line 404FF2 Water Line Connection 418263 Plastic Nut & Sleeve Assy 412547 Cabinet Foot (4) 413198 Dryer 269210 Fan Motor, Condenser 526311 Fan Blade, Condenser 518812 Condenser 1951-FFS13 Back Panel 11769


16 Power Cord 224217 Solenoid Valve 2552A18 *Compressor 5405-FFS19 ***Relay/Overload 542121 Bypass Valve Assy 2749-S24 Drain Pan 31550-1-F25 **Capacitor 542226 **Insulation 31612

* Replaces P/N 5402-FFS through installation of kit.** New part added through installation of kit.*** Replaces P/N's 5413 & 5414 through installation of kit.

PTC RELAY

RUNNING CAPACITOR

MS

C

188 24

12 21 7

16

10

112613

2

1

3

17

19

25

COMBO75FFb


44

COMBO 75FF (1 of 2)New Design Starting With Serial Numbers

7CF600000

For Item #10, see Model 402 Ice Maker (page 40) for separate breakdown.For Stainless Steel Models, see page 39 for handles and hinges.


1 Handle 31489-4*2 Door Gasket 31493-4*3 Door Shelf Retainers (3) 31521-14 Shelf Retainer Rivet (6) 418245 Door Switch 19166 Door Assy 75-DOOR*7 Hinge, Top 11849-ST*8 Pivot Screw, Top 41785-SS*9 Dr Switch Brkt 1171210 Ice Maker Assy 40211 Ice Bucket 3150112 Control 271713 Control Knob 4149214 Switch On-Off 205315 Lamp Bulb 3131716 Ice Bin Door 31523-S

`Item Description Part No.

17 Glass Shelf (1) 31427-118 Glass Half Shelf (1) 3143519 Grille 11664*20 Glass Short Shelf (2) 31423-121 Trim Strip, Front Long (2) 31443-422 Trim Strip, Front Short (2) 31443-223 Timer 2632-2-S24 Fan Motor, Evaporator 5299-125 Fan Blade, Evaporator 3165626 Hinge, Bottom 11849-SB*27 Pivot Screw, Bottom 41747-SS*28 Freezer Housing 11537-S29 Ice Bin Door Hinge 3146330 Evaporator & Heat Exchanger 2631-57531 Light Cover 3131432 Lamp Holder NLA

*Please indicate color

9

1

11

2627

43

872

1923513

1214

617

22

7

18

21

20

28

2524

16

10

29

1531

32

COMBO75FFc

45

75FF (2 of 2)New Design Starting With Serial Numbers

7CF600000


1 Water Line 404FF2 Water Line Connection 418263 Plastic Nut & Sleeve Assy 412544 Cabinet Foot (4) 413195 Dryer 26926 Fan Motor, Condenser 53007 Fan Blade, Condenser 54288 Condenser 1951-FFS9 Back Panel 11769


10 Power Cord 231811 Solenoid Valve 2552A12 Compressor 5405-FFS13 Relay/Overload 542114 Bypass Valve Assy 2749-S16 Drain Pan 31550-1-F17 Capacitor 542218 Insulation 31612

C

S M

PTC RELAY

RUNNING CAPACITOR

1

3

11

2

10

4

5 16

12

8 14

7 6

13

17

9

18

COMBO75FFd


46

COMBO ULN-CO29FF (1 of 2)Serial Numbers

2CF300000, 2CF400000 or 2CF500000



1 Handle 31489-3*2 Door Gasket 31493-3*3 Door Shelf Retainer (Long) 31521-24 Door Shelf Retainer (Short) 31521-35 Fan Blade, Evaporator 316566 Pivot Hinge, Top 11697-ST*7 Pivot Hinge, Bottom 11695-S*9 Ice Maker Assy 40210 Ice Bucket 3150111 Complete Door Assy 29-DOOR*12 Control 271713 Grille 11663*14 Ice Bin Door 31523-S


15 Glass Shelf (2) Short 31425-116 Switch On-Off 205317 Ice Bin Door Hinge (2) 3146318 Shelf Retainer Rivet (6) 4182419 Trim Strip, Front Short (2) 31443-120 Pivot Screw, Top 41785-SS*21 Condenser 1893-FFS22 **Timer 2632-123 Fan Motor, Evaporator 5299-124 Pivot Screw, Bottom 41747-SS*25 Freezer Housing 11471-S26 Control Knob 4149227 Evaporator & Heat Exchanger 2631-S29

*Please indicate color.**Replaces P/N 2595 or 2632 through installation of kit.

7

2

4

1626

15

19

9

17

206

24

1

18

14

52327

11

13

1221

25

310

COMBO29FFa

47

COMBO ULN-CO29FF (2 of 2)Serial Numbers

2CF300000, 2CF400000 or 2CF500000


1 Water Line 404FF2 Water Line Connection 418263 Plastic Nut & Assy 4125412 Cabinet Foot (4) 4112513 Dryer 269215 Fan Motor, Condenser 526316 Fan Blade, Condenser 518818 Back Panel 11545-1


19 Power Cord 231720 Solenoid Valve 2552A22 ** Relay/Overload 542124 * Compressor 5405-FFS25 By-Pass Valve Ass'y 2749-S28 Drain Pan 31550-1-F29 **Capacitor 542230 **Insulation 31622

* Replaces P/N 5402-FFs through installation of kit.** New part added through installation of kit.*** Replaces P/N's 5413 and 5414 through installation of kit.

C

S M

PTC RELAY

RUNNING CAPACITOR

12

25

19

1328

16

30

24

18

1

3

20

2

15

22

29

COMBO29FFb


48

COMBO ULN-CO29FF (1 of 2)Serial Number 2CF600000



1 Handle 31489-3*2 Door Gasket 31493-3*3 Door Shelf Retainer (Long) 31521-24 Door Shelf Retainer (Short) 31521-35 Fan Blade, Evaporator 316566 Pivot Hinge, Top 11697-ST*7 Pivot Hinge, Bottom 11695-S*9 Ice Maker Assy 40210 Ice Bucket 3150112 Complete Door Assy 29-DOOR*13 Control 271714 Grille 11663*15 Ice Bin Door 31523-S


16 Glass Shelf (2) Short 31425-117 Switch On-Off 205318 Ice Bin Door Hinge (2) 3146319 Shelf Retainer Rivet (6) 4182420 Trim Strip, Front Short (2) 31443-121 Pivot Screw, Top 41785-SS*22 Condenser 1893-FFS23 Timer 2632-2-S24 Fan Motor, Evaporator 5299-125 Pivot Screw, Bottom 41747-SS*26 Freezer Housing 11471-S27 Control Knob 4149228 Evaporator & Heat Exchanger 2631-S29

*Please indicate color.

23

21

6

25

4

1

18

245

15

9

3

212

20

7

16

1322

10

26

141727

28 19

COMBO29FFc

49

COMBO ULN-CO29FF (2 of 2)Serial Number 2CF600000


1 Water Line 404FF2 Water Line Connection 418263 Plastic Nut & Sleeve Assy 4125412 Cabinet Foot (4) 4112513 Dryer 269215 Fan Motor, Condenser 530016 Fan Blade, Condenser 542818 Back Panel 11545-1


19 Power Cord 231720 Solenoid Valve 2552A22 Relay 542124 Compressor 5405-FFS25 By-Pass Valve Ass'y 2749-S28 Drain Pan 31550-1-F29 Capacitor 542230 Insulation 31622

C

MS

RUNNING CAPACITOR

PTC RELAY

25

24

20

3

1

222

29

30

16

15

24

18

13 1228

19

COMBO29FFd


50

( COMBO 75A MANUAL DEFROST HYBRID (1 OF 2)Serial Numbers

U-Combo 75A 2004 Design

14

12

15

13

16

8, 97 10, 11

6

5

4

3

1, 2 17

18

19

20

21, 22

23

CO75A_001

51

Item Description Black Stainless Steel1 Glass Shelf (Full) 40003 400032 Front Edge Trim 31443-9 31443-93 Ice Bucket 31687 316874 Bin Door Assembly 11957-S 11957-S5 Ice Maker Assembly 402-C75A 402-C75A6 Back Panel 11769 117697 Ice Bin Door Hinge 31463 314638 Lamp Cover 11859 118599 Lamp Bulb 31317 3131710 Glass Shelf (Narrow) 40002 4000211 Front Edge Trim 31443-8 31443-812 Top Hinge Assembly 11849-ST BLK 242-1-SS13 Top Pivot Screw 41785-SSB N/A14 Bottom Hinge Assembly 11849-SB BLK 245-1-SS15 Bottom Pivot Screw 41747-SSB N/A16 Door Assembly 75-DOORBLK 75-DOORSS17 Grille 11664 1166418 Control Knob 42067 4206719 Door Handle 31489-4-BLK 4201920 Door Gasket 31493-4-GRY 31493-4-GRY21 Door Shelf Retainer 31521-1 31521-122 Shelf Retainer Rivet 41824 4182423 Door Switch Actuator 11712 11712

COMBO 75A MANUAL DEFROST HYBRID (1 OF 2)


52

(COMBO 75A MANUAL DEFROST HYBRID (2 OF 2)Serial Numbers


6

3

5

4

11

10

9

7

8

13

12

1415

1617

2

1

CO75A_002

53

Item Description Black Stainless Steel1 Fan Blade 5188 51882 Fan Motor 5263 52633 Water Line Connection 41826 418264 Water Line Assembly 404 4045 Plastic Nut & Sleeve Assembly 41254 412546 Water Valve 2552A 2552A7 Dryer 2694 26948 Evaporator & Heat Exchanger 74000-75/29 74000-75/299 Compressor Assembly 5402-S 5402-S10 Relay 5414 541411 Overload 5413 541312 Power Cord 2913 291313 Control 2781 278114 Light Switch 1916 191615 On / Off Switch 2053 205316 Condensor Assembly 1951-S 1951-S17 Cabinet Feet 41319 41319

COMBO 75A MANUAL DEFROST HYBRID (2 OF 2)


54

COMBO 75A (1 of 2)



1 Handle 31489-4*2 Door Gasket 31493-4*3 Door Shelf Retainers (3) 31521-14 Shelf Retainer Rivet (6) 418245 Door Switch 19166 Door Assy 75-DOOR*7 Hinge, Top, 3 Hole 11697-ST*

Hinge, Top, 4 Hole 11849-ST*8 Pivot Screw, Top 41785-SS*9 Dr Switch Brkt 1171210 Ice Maker Assy 40211 Ice Bucket 3150112 Control 276313 Control Knob 4149214 Switch On-Off 2053


15 Lamp Holder NLA16 Lamp Bulb 3131717 Ice Bin Door 31523-S18 Glass Shelf (1) 31427-119 Glass Half Shelf 3143520 Grille 11664*21 Glass Short Shelf (2) 31423-122 Trim Strip, Front Long (2) 31443-423 Trim Strip, Front Short (2) 31443-224 Hinge, Bottom, 3 Hole 11697-SB*

Hinge, Bottom, 4 Hole 11849-SB*25 Pivot Screw, Bottom 41747-SS*26 Ice Bin Door Hinge 3146327 Light Cover 31314


COMBO75Aa

9

16 627

21

2123

15

23

1213

1

11

2425

43

872

20514

18

1922

17

10

26

COMBO75Aa

55

COMBO 75A (2 of 2)


1 Water Line 4042 Water Line Connection 418263 Plastic Nut & Sleeve Assy 412544 Cabinet Feet (4) 413195 Dryer 26946 Evaporator & Heat Exchanger 2189-757 Fan Motor 52638 Fan Blade 5188


9 Condenser 1951-S10 Back Panel 1176911 Power Cord 1855-112 Solenoid Valve 2552A13 Compressor 5402-S14 Relay 541415 Overload 5413

6

9

13

2

12

15

14

11

4

7

513

8

10

COMBO75Ab


COMBO75Ab


56

COMBO 29A MANUAL DEFROST HYBRIDSerial Numbers


2

3

4

5

6 7, 89

10

11

12

13

14

1516

18

17

19

30

27

29

28

36

35

26

25

31

3233

24

2021

2223

34

1

CO29ACO29A

57

Item Description White-Marine Black1 Pin for Travel Pin Assembly 31476-SS 31476-BLK2 Back Panel 11545-1 11545-13 Travel pin assembly SLV-TRAVEL-PIN TRVL-PIN-CO29B4 Ice Maker Assembly 402-C29A 402-C29A5 Ice Bin Door Hinge 31463 314636 Bin Door Assembly 11957-S 11957-S7 Glass Shelf 31425-03 31425-038 Front Edge Trim 31443-6 31443-69 Top Hinge Assembly 11698-SSWT 11697-STBLK10 Top Pivot Screw 41785-SSW 41785-SSB11 Ice Bucket 31687 3168712 Door Handle 11777-29 31489-3-BLK13 Door Gasket 31493-3-WHT 31493-3-GRY14 Door Assembly 80-17031-02 80-17014-0115 Shelf Retainer Rivet 41824 4182416 Door Shelf Retainer 31521-2 31521-217 Bottom Hinge Assembly 11696-S-KIT 11695-S-BLK18 Bottom Pivot Screw 41747-SSS 41747-SSB19 Grille 11663-SPL 11663-BLK20 Control Knob 42067 4206721 Control 2782 278222 On / Off Switch 2053 205323 Condensor Assembly 1893-S 1893-S24 Cabinet Feet 41125 4112525 Fan Blade 5188 518826 Fan Motor 5263 526327 Water Line Connection 41826 4182628 Water Line Assembly 404 40429 Plastic Nut & Sleeve Assembly 41254 4125430 Water Valve 2552A 2552A31 Evaporator & Heat Exchanger 7400-75/29 7400-75/2932 Dryer 2693 269333 Compressor Assembly 5402-S 5402-S34 Power Cord 2374 237435 Overload 5413 541336 Relay 5414 5414

COMBO 29A MANUAL DEFROST HYBRID


58

COMBO 29A (1 of 2)



1 Handle 31489-3*2 Door Gasket 31493-3*3 Door Shelf Retainer (Long) 31521-24 Door Shelf Retainer (Short) 31521-35 Pivot Hinge, Top 11697-ST*6 Pivot Hinge, Bottom 11695-S*8 Ice Maker Assy 4029 Ice Bucket 3150110 Complete Door Assy 29-DOOR*11 Control AR-19-1212 Grille 11663*


13 Ice Bin Door 31523-S14 Glass Shelf (2) Short 31425-115 Switch On-Off 205316 Ice Bin Door Hinge (2) 3146317 Shelf Retainer Rivet (6) 4182418 Shelf Trim Strip Front (Short) 31443-119 Pivot Screw, Top 41785-SS*20 Condenser 1893-S21 Pivot Screw, Bottom 41747*22 Control Knob 41492


19

5

21

4

1

16

13

3

210

18

6

14

2220

9

121511

17

COMBO29Aa

COMBO29Aa

59

COMBO 29A (2 of 2)


1 Water Line 4042 Water Line Connection 418263 Plastic Nut & Sleeve Assy 412544 Cabinet Foot (4) 411255 Dryer 26946 Evaporator & Heat Exchanger 2189-297 Fan Motor 5263


8 Fan Blade 51889 Back Panel 11545-110 Power Cord 1855-111 Solenoid Valve 2552A12 Relay 541413 Compressor 5402-S14 Overload 5413

DETAIL "A"

SEE DETAIL "A"

13

11

2

14

12 4

9

8

7

13

56

10

COMBO29Ab


60

MODEL 95 (1 of 2)



1 Switch - On/Off 20532 Handle 31489-1*3 Door Gasket 31493-1*4 Pivot Hinge, Top 11697-ST*5 Pivot Hinge, Bottom 11695-S*7 Grille 11662*8 Condenser Assy 2628-S


9 Ice Maker Assy 40210 Ice Bucket 3142911 Inner Liner Assy/Evaporator 2182-S*12 Complete Door Assy 95-DOOR*13 Pivot Screw, Top 41785*14 Pivot Screw, Bottom 41747*15 Control 2783

12

314

134

2

5

15 7

1

8

10

11

9


MODEL95a

61

MODEL 95 (2 of 2)


1 Water Line 4042 Water Line Connection 4053 Plastic Nut & Sleeve Assy 412544 Compressor 5401-S5 Capacitor 54208 Cabinet Feet (4) 411259 Dryer 2694


10 Fan Motor 526311 Fan Blade 518813 Back Panel-Formed 1144414 Power Cord 1855-115 Insulator Tube Armaflex 3115416 Solenoid Valve 2552A17 Relay 5419

MS

RUNNING CAPACITOR

PTC RELAY

C

13

14

9

8

10-11154

17

5

2

161

3

MODEL95b


62

MODEL 98 (1 of 2)



1 Switch-On/Off 20532 Handle 31489-2*3 Door Gasket 31493-2*4 Pivot Hinge, Top 11697-ST*5 Pivot Hinge, Bottom 11695-S*7 Grille 11661*8 Condenser Assy 2628-S


9 Ice Maker Assy 40210 Ice Bucket 3143011 Inner Liner Assy/Evaporator 2183-S*12 Complete Door Assy 98-DOOR*13 Pivot Screw, Top 41785*14 Pivot Screw, Bottom 41747*15 Control 2783

413

14

2

9

3

5

11

10

8

1

715

12


MODEL98a

63

MODEL 98 (2 of 2)


1 Water Line 4042 Water Line Connection 4053 Plastic Nut & Sleeve Assy 412544 Compressor 5401-S5 Capacitor 54206 Cabinet Feet (4) 411257 Dryer 2694


8 Fan Motor 52639 Fan Blade 518810 Solenoid Valve 2552A11 Back Panel-Formed 1144312 Power Cord 1855-113 Relay 5419

C

S M

RUNNING CAPACITOR

PTC RELAY

2

110

3

5

13

98,7

6

411

12

MODEL98b


64

MODEL BI15 (1 of 2)

For Item #9, see Model 402 Ice Maker (page 40) for separate breakdown.For Stainless Steel Models, see page 39 for handles and hinges.


1 Switch- On/Off 20532 Handle 31489-2*3 Door Gasket, Lower 31606*4 Pivot Hinge, Top 11697-ST*5 Pivot Hinge, Bottom 11695-S*7 Grille 31543*8 Condenser Assy 2223-S9 Ice Maker Assy 402


10 Ice Bucket 3143012 Complete Door Assy BI15-DOOR*13 Pivot Screw, Top 41785-SS*14 Pivot Screw, Bottom 41747-SS*15 Gasket, Upper 31604*16 Control 269117 Control Knob 41492

17

5

14

12

13

42

3

15

81

167

10

9


MODELBI15a

65

MODEL BI15 (2 of 2)


1 Water Line 4042 Water Line Connection 418263 Plastic Nut & Sleeve Assy 412544 Compressor 5402-S5 Overload 54136 Cabinet Feet (4) 413197 Dryer 2694


8 Fan Motor 52639 Fan Blade 518810 Solenoid Valve 2552A11 Back Panel-Formed 4180212 Power Cord 1855-113 Relay 5414

13

5

13

2

10

98,7

6

12

411

MODELBI15b


66

MODEL SP18 (1 of 2)



2 Handle 117773 Door Gasket 31493-1*4 Pivot Hinge, Top 11698-SS*5 Pivot Hinge, Bottom 11696-SS*6 Grille 118707 Condenser Ass'y 2258-S8 Ice Maker Ass'y 4029 Ice Bucket 3142910 Inner Liner Assy/Evaporator 2182-S18

Item Description

11 Complete Door Ass'y, White WHT95M-DRComplete Door Ass'y, Black 95-DOORBG

12 Pivot Screw, Top 41747-SSS13 Pivot Screw, Bottom 41747-SSS14 On-Off Switch 205315 Travel Pin Ass'y TP91-GRY-116 Travel Pin (Pin Only) 31476-SS17 Frame 11810-KIT

614

717

5

8

9

10

1516

412

13

2

3

11


MODELSP18a

67

MODEL SP18 (2 of 2)


1 Water Line 4042 Water Line Connection 418263 Plastic Nut & Sleeve Ass'y 412544 Compressor 5402-S5 Overload 54136 Relay 54147 Cabinet Feet 411258 Dryer 2694


9 Fan Motor 526310 Fan Blade 518811 Back Panel 1181112 Power Cord 226413 Solenoid Valve 2552A14 Cold Control 278315 Base 2294

11

4

15

7

8

14

9

10

12

5

6

13

2

13

MODELSP18b


68

MODEL 75RFFor Stainless Steel Models, see page 39 for handles and hinges.


1 Dr Switch Brkt 117122 Grille 11664*3 Glass Shelves (2) 31427-14 Condenser 1951-FFS5 Door Switch 19166 Control 2302-S8 Lamp Bulb 313179 Freezer Door Assy 3137910 Hinge, Bottom, 3 Hole 11697-SB*

Hinge, Bottom, 4 Hole 11849-SB*11 Mullion 3160213 Hinge, Top, 3 Hole 11697-ST*

Hinge, Top, 4 Hole 11849-ST*14 Overload 541115 Door Gasket 31493-4*16 Door Handle 31489-4*17 Door Shelf Retainers (3) 31521-118 Solenoid Valve Assy 2749-S19 Glass Half Shelf (1) 3143520 Door Assy 75-DOOR*21 Evaporator Fan 5299-1


22 Evaporator Fan Blade 3165623 Back Panel 1176924 Timer 6800025 Pivot Screw, Top 41785*26 Dryer 269227 Fan Motor, Condenser 530028 Fan Blade, Condenser 542829 Compressor 5400-FFS30 Power Cord 231931 Evaporator & Heat Exchanger 2695-FFS32 Insulator Tube 3141033 Leveler Feet (4) 4131934 Shelf Retainer Rivets (6) 4182435 Trim Strip 31443-436 Pivot Screw, Bottom 41747*37 Drain Pan 31550-1-F38 Relay 541239 Light Cover 3131440 Lamp Holder NLA41 Freezer Door Bushings 41346-4

1

839

40

3314

23314

151036

2513

2

24

4

19

35

311

2221

9

4113

30

26 3729

27 18

28

32

14

38

16

17 34

6 5

20


MODEL75RF

69

MODEL 75WCFor Stainless Steel Models, see page 39 for handles and hinges.


1 Dr Switch Brkt 117122 Grille 11664*3 Wine Shelf 23004 Condenser 1951-S5 Switch 19166 Control 2767-S7 Control Knob-Silver 41715

Alternate Control Knob-Black 414928 Lamp Bulb 313179 Shelf Clip 3164810 Drain Cup 1150811 Drain Pan 31550-1-F12 Drain Trough 31391-113 Hinge, Top RH/Bottom LH 242*

Hinge, Top, 4 Hole 242-1*14 Hinge, Bottom RH/Top LH 245*

Hinge, Bottom, 4 Hole 245-1*15 Door Gasket 31493-4*


16 Door Handle 41984-3*17 Compressor 5400-S18 Glass Half Shelf (1) 3143519 Door Assy 75WC-DOOR*20 Light On-Off Switch 205321 Lamp Holder NLA22 Overload 541123 Back Panel 1176924 Light Cover 3131425 Dryer 269426 Fan Motor 526327 Fan Blade 518828 Power Cord 231529 Evaporator & Heat Exchanger 2186-S30 Leveler Feet (4) 4131931 Lock Assy 41734-S32 Relay 5412

19

3029

2511

26

27281723

14

3116

13

15

10

12

256

720

4

18

39

24821

22

32

1


MODEL75WC


70

MODEL 75F


2 Grille 11664*3 Glass Shelves (2) 31427-14 Condenser 1951-S5 Control 25806 Control Knob-Silver 417157 Glass Half Shelf (1) 314358 Pivot Screw, Top 41785-SS*9 Hinge, Top 11697-ST*

Hinge, Top, 4 Hole 11849-ST*10 Door Gasket 31493-4*11 Door Handle 31489-4*12 Door Shelf Retainers (3) 31521-113 Compressor 5402-S14 Shelf Retainer Rivet (6) 41824


15 Door Assy 75-DOOR*16 Overload 541317 Pivot Screw, Bottom 41747-SS*18 Back Panel 1176919 Dryer 269420 Fan Motor 526321 Fan Blade 518822 Power Cord 223423 Leveler Feet (4) 4131924 Trim Strip (4) 31443-425 Evaporator 2187-FS26 Hinge, Bottom 11697-SB*

Hinge, Bottom, 4 Hole 11849-SB*27 Relay 5414

16

2723

19

222120413

18

10

7

24

3

25

1726

98

11

12

14

25

6

4

15


MODEL75F

71

MODEL 75RFor Stainless Steel Models, see page 39 for handles and hinges.


1 Dr Switch Brkt 117122 Grille 11664*3 Glass Shelves (2) 31427-14 Condenser 1951-S5 Door Switch 19166 Control 2923-S8 Lamp Bulb 313179 Glass Half Shelf (1) 3143510 Drain Cup 1150811 Drain Pan 31550-1-F12 Drain Trough 31391-113 Hinge, Top, 3 Hole 11697-ST*

Hinge, Top, 4 Hole 11849-ST*14 Pivot Screw, Top 41785-SS*15 Door Gasket 31493-4*16 Door Handle 31489-4*17 Door Shelf Retainers (3) 31521-118 Compressor 5400-S


19 Shelf Retainer Rivets (6) 4182420 Door Assy 75-DOOR*22 Overload 541123 Back Panel 1176924 Trim Strips, Front Long (3) 31443-425 Trim Strips, Rear Long (2) 31444-426 Dryer 269427 Fan Motor 526328 Fan Blade 518830 Power Cord 230631 Evaporator & Heat Exchanger 2333-S33 Leveler Feet (4) 4131934 Hinge, Bottom, 3 Hole 11697-SB*

Hinge, Bottom, 4 Hole 11849-SB*35 Pivot Screw, Bottom 41747-SS*36 Relay 541237 Light Cover 3131438 Light Holder NLA

38

37

15

2711

14

253112

109

24

3

25

22

36

30

28

23

2618

33

3534

13

16

17

19

25

64

8

1

20


MODEL75R


72

75 BEV

20

22

25

24

23

19

6

21

5

321

4

7

11

1210

1314

18

1617

8

9

15

MODEL75BEV


1 Back Panel 117692 Light Bulb 313173 Light Cover 118594 Top Door Hinge 242-1-SS

5 Door Assembly Right Hand 80-17044-03Door Assembly Left Hand 80-17044-136 Door Gasket 31493-4-GRY7 Bottom Door Hinge 245-1-SS8 Door Switch Bracket 117129 Door Switch 191610 Rocker Switch 205311 Grille 1166412 Control 2923


13 Condenser Assembly 1951-S14 Leveling Leg 4131915 Control Knob 4206716 Fan Blade 518817 Fan Motor 526318 Drain Pan 31550-1-F19 Compressor Assembly 5400-S20 Overload 541121 Relay 541222 Glass Shelf Assembly 40009-0123 Power Cord 231524 Evaporator Assembly 2186-S25 Rack Assembly 80-33002-S

73

MODEL 75AD


1 Dr Switch Brkt 117122 Grill

uline ice service_manual

Documents

uline products

entire line of u

uline corporationwww

uline corporation8900

uline corporationpo

line productswhich

parts listing

system dehydration