typical elevation · 2018. 10. 22. · alucobond cladding panels wall cladding 12 extruded...
TRANSCRIPT
TYPICAL ELEVATION
COVER SHEET
PAGE
P01
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page1 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
VERTICAL JOINT01
12
25
LOW MODULUS SEALANTOR GASKET
EXTRUDED ALUMINIUMSUB-FRAME AB 416
ALUMINIUM FIXINGCLIPS 40 x 20mm,WITH SPACER, ROTATE90° TO FREE PANEL
TOP HAT
ALUCOBOND CLADDINGPANELS
RIVET OR SCREWALUCOBOND TO CLIP
SARKING BY OTHERS
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
VERTICALJOINT
PAGE
P02
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page2 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
VERTICAL JOINT(ALTERNATIVE)01
12
25
LOW MODULUS SEALANTOR GASKET
ALUCOBOND CLADDINGPANELS
RIVET OR SCREWALUCOBOND TO CLIP
70
ISOLATION TAPEBETWEEN STEEL
& ALUMINIUM SURFACES
TOP HATSARKING BY OTHERS
EXTRUDEDALUMINIUMSUB-FRAMEAB 416
EXTRUDEDALUMINIUMSUB-FRAMEAB 415
VERTICALJOINT
PAGE
P03
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page3 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
PARAPETDETAIL02
ALUCOBOND CLADDINGPANELS
SHIMAS REQ.
ALUCOBONDCLADDINGPANELS
TOP HAT
MOISTURE BARRIERAS REQ.
PARAPETDETAIL
PAGE
P04
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page4 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
SEALANT
PARAPET LINING
HORIZONTALJOINT DETAIL03
12
ALUCOBOND CLADDINGPANELS
EXTRUDEDALUMINIUMSUB-FRAMEAB 416
25
35
EXTRUDEDALUMINIUMSUB-FRAMEAB 415
TOP HAT
LOW MODULUSSEALANT
OR GASKETRIVET OR SCREWALUCOBOND TO CLIP
SARKING BY OTHERS
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
HORIZONTALJOINT
PAGE
P05
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page5 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
SILLDETAIL04
12
ALUCOBOND CLADDINGPANELS
25
35
TOP HAT
LOW MODULUSSEALANT
OR GASKET
RIVET OR SCREWALUCOBOND TO CLIP
CONCRETE SLAB
EXTRUDEDALUMINIUMSUB-FRAMEAB 416
EX. EXTRUDEDALUMINIUMSUB-FRAMEAB 415
CUT OFF
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
SARKING BY OTHERS
SILLDETAIL
PAGE
P06
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page6 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
WINDOW HEADDETAIL05
ALUCOBONDCLADDING
PANELS
12
LOWMODULUSSEALANT
OR GASKET
RIVET OR SCREWALUCOBOND TO CLIP
EXTRUDEDALUMINIUMSUB-FRAMEAB 416
EX. EXTRUDEDALUMINIUMSUB-FRAMEAB 415
CUT OFF
TOP HAT
SARKING BY OTHERS
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
WINDOW HEADDETAIL
PAGE
P07
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page7 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
JAMBDETAIL06
ALUCOBONDCLADDING
PANELS
WALLCLADDING
12
EXTRUDEDALUMINIUMSUB-FRAME
AB 416
EX. EXTRUDEDALUMINIUMSUB-FRAMEAB 415
CUT OFF
LOW MODULUSSEALANTOR GASKET
RIVET ORSCREW
ALUCOBONDTO CLIP
TOP HAT
SARKING BY OTHERS
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
JAMBDETAIL
PAGE
P08
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page8 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
07
ALUCOBONDCLADDING
PANELS
TOP HAT
ALUCOBONDCLADDING
PANELS
70
SARKING BY OTHERS
12
25
EXTRUDEDALUMINIUMSUB-FRAME
AB 416
EXTRUDEDALUMINIUMSUB-FRAMEAB 415
35
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
50
SOFFITDETAIL
SOFFITDETAIL
PAGE
P09
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page9 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
SOFFITDETAIL08
TOP HAT
ALUCOBONDCLADDING
PANELS12
LOW MODULUSSEALANT
OR GASKET
25
EX. EXTRUDEDALUMINIUMSUB-FRAMEAB 416
EXTRUDEDALUMINIUMSUB-FRAME
AB 415
35
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
SARKING BY OTHERS.
CUT OFF
CORNERDETAIL
PAGE
P10
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page10 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
OUTSIDE CORNERDETAIL09
ALUCOBONDCLADDINGPANELS
TOP HAT
ALUCOBONDCLADDING
PANELS
12
LOW MODULUSSEALANT
OR GASKET
25
EXTRUDEDALUMINIUMSUB-FRAME
AB 416
EXTRUDEDALUMINIUMSUB-FRAME
AB 415
35
70 N
OM
.
TOP HAT
SARKING BY OTHERS
ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
TO SUIT
CORNERDETAIL
PAGE
P11
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page11 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
STIFFENERDETAIL10
TOP HAT
ALUCOBOND CLADDINGPANELS
TOP HAT
tesa 7078 / 3M VHB4991 TAPE
SARKING BY OTHERS
NOTE: TO ENSURE APPLIED LOADS ARE TRANSFERRED BACKTO THE SUB STRUCTURE, ALL STIFFENERS SHOULD BE FIXEDBACK TO THE CASSETTE EDGE. REQUIREMENTS INCLUDING;GAUGE, MATERIAL TEMPER, CENTRES / SPANS TO BEDETERMINED BY QUALIFIED PROFESSIONAL SPECIFIC TO THEAPPLICATION.
STIFFERDETAIL
PAGE
P12
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page12 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
WINDOW SILLDETAIL11
ALUCOBONDCLADDINGPANELS SARKING BY OTHERS
SILICONESEAL
TOP HAT25
35
CUT OFF
RIVET OR SCREWALUCOBOND TO CLIP
EX. EXTRUDEDALUMINIUMSUB-FRAMEAB 415ISOLATION TAPE BETWEENSTEEL & ALUMINIUM SURFACES
WINDOW SILLDETAIL
PAGE
P13
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page13 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.
HORIZONTAL JOINT DETAIL
ALUCOBOND CLADDINGPANELS
EXTRUDEDALUMINIUMSUB-FRAMEAB 416
EXTRUDEDALUMINIUMSUB-FRAMEAB 415LOW MODULUS SEALANT
HORIZONTAL DETAIL
PAGE
P14
ALUCOFIXSYSTEM
Alucobond Fixing SystemsJune 2017
Page14 of 14
[email protected]/alucobondarchitectural
© ALUCOBOND ARCHITECTURAL.ALL RIGHTS RESERVED. THIS DESIGN IS COPYRIGHT AND CAN NOT BEREPRODUCED OR COPIED IN ANY FORM EITHER IN PART OR IN WHOLEWITHOUT THE WRITTEN PERMISSION OF ALUCOBOND ARCHITECTURAL25 WEST PARK DRIVE, DERRIMUT VIC 3030
THIS INFORMATION IS GENERIC IN NATURE & SUPPLIEDFOR GUIDANCE PURPOSES ONLY. JOINT WIDTHS WILL
VARY TO SUIT PANEL SIZE & SEALANT USED.TOP HAT DIMENSIONS ARE NOMINAL. DIMENSIONS,
SPACING, SPANS & STIFFENER REQUIREMENTS WILL NEEDTO CONFIRMED BY A SUITABLY QUALIFIED PROFESSIONAL
TO SUIT THE SPECIFIC APPLICATION.