tubeless tyre
DESCRIPTION
Tubeless tyreTRANSCRIPT
1. INTRODUCTION
It has been over a century from the time Dunlop patented his 'mummified wheel' to the
modern radial tyres of today. Yet with all the improvements a tyre has undergone, one
thing remained unchanged, which is only when it is inflated to the optimised level and
that inflation is kept constant that it can deliver maximum comfort and performance. This
is one of the basic reasons all tyre manufacturers try to focus on in the development stage
of a tyre which can have the best air retention ability. Usage of a tube or an extra air
container within the tyre was regarded as the best solution for many years
It may come as a surprise to many that in 1903, engineer Paul Weeks Litchfield, then in
his early 20s, was granted a patent for the first 'tubeless' tyres. He later rose to be
the chairman of the Board of Goodyear in the year 1940. Just like many other patents,
which were granted during that period, this concept was not pursued until late 1939 when
the requirement for the first amphibious tyre was felt. The 120x33.5 - 66 smooth tread
Marsh Buggy tyres, by far the largest tyres produced then, were used on Admiral Byrd's
Snow Cruiser. This vehicle was capable of carrying very heavy loads over all sorts of
terrain, even float on water. These were off-the-road tyres, flexible but inextensible
pressure vessel that were pre-stressed and skin-stressed by air pressure. To produce such
tyres Goodyear at Akron employed the idea of Litchfield, using nylon cords for the first
time and a newly developed synthetic rubber compound called Chemigum to line the
inner casing of this tyre to lighten its weight and eliminate the tube.
The Second World War highlighted the need for reliable tyres as loss of air or punctures
cost precious moments or even endangered lives. Though the tubeless concept was not
used during the war, subsequent development of tyres with a 'run-flat' capability by
introducing tubes, which had a special construction of a sealant on the lower side, this
allowed it to run without an air loss even after a penetration. The added weight of the
tube made the steering wheel heavy and restricted speed. They were used on low speed
trucks, which traveled on areas with puncture hazards like wrecker's equipment, dock
and warehouse vehicles, and other utility trucks
To reduce weight lifeguard tubes were introduced, having two air chambers, the outer
rubber tube with a thick canvas tube inside. In case of a blowout only the outer chamber
gave way, while the reserve air in the thick canvas tube would not allow the tyre to be
completely deflated allowing the vehicle for a safe straight line gradual stop.
After the war a more determined effort towards elimination of the inner tube was sought
as it was considered the main source of service trouble and failures while being clearly
superfluous and costly. Experiments were therefore conducted both in the USA (initially
by Goodrich) and in UK (by Dunlop), towards providing a near perfect seal between the
tyre bead and rim, under all service conditions. This meant that the tyre had to run even at
low inflation pressures or with a penetration to a safe distance without loss of vehicle
control. It was in the year 1954 that the first commercially realised tubeless tyre was
fitted as original equipment, by the now defunct Packard marque.
During the mid 1950s and early 1960s, India too manufactured tubeless tyres, which were
not only supplied as original equipment for the cars, but also had a number of sizes meant
for the replacement market. While the rest of the world accepted this new technology and
by the middle of 1962, nearly all commercial vehicles, trucks and passenger cars
used tubeless tyres, we in India reverted to the old tube-tyre theory. Even though most
companies in India still manufacture tube-type tyres, many have the tubeless technology
available with them and do manufacture tubeless tyres meant for export only.
Tubeless tyres have reappeared in the Indian scenario but many users are reluctant to use
them. Some fit tubes in them. So which is actually better? Let us see where the
construction difference lies. Apart from the basic construction, which remains the same
with the run of the cords distinguishing the type of tyre construction, whether it is a
cross-ply or a radial ply one; the main difference lies in the application of the inner liner
of the carcass. Whereas in a tube-type construction the inner liner acts as a medium for
reducing friction between the cord body and the tube, in a tubeless construction this is the
tube itself. Thus the inner liner in a tubeless tyre is made up of a Halogenated Butyl
rubber like Chlorobutyl or Bromobutyl for better air impermeability together with high
heat and weather resistance.
Though compounds used in a tubeless or a tube type tyre may vary, the other major
difference lies in the bead area of the tyre. While considering a radial tyre both type of
tyres have a flexible yet rigid bead, where the bead bundle is very thin and the stability of
the tyre is enhanced by the bead apex or bead filler controlling it, in a tubeless it also has
to maintain the air pressure within. Thus the bead heel in the tubeless sits more tightly
within the flange of the rim, and to ensure this tight fitting most tyre manufacturers add
an extra wrapping over the bead area. This enhances high-speed performance while
achieving a better cornering ability on the tubeless.
The other advantages are the absence of a tube make the tyre lighter in weight, thus has
less chance of vibrations, which means that it leads to a better fuel saving. Even the
rolling resistance in a tubeless radial is lower when compared to a tube type radial. This
is due to the fact that the tubeless tyre sidewall is more supple as there is no internal body
to create a friction. This also helps the tyre to run cooler as it eliminates heat generation
caused by the internal shuffling of the tube.
The inner liner also acts as an absorbent during a nail penetration making the nail act like
a plug and therefore the tyre has a slow leak and not a sudden deflation as it occurs on a
tube- type tyre. This can be illustrated by a simple example. Pierce an ordinary balloon
with a pin and it disintegrates, while sticking a cello tape on the balloon would enable the
pin to penetrate without it bursting.
Similarly by comparing a tubeless tyre to a balloon that is not fully inflated, when
squeezed this would deshape to certain extent before it bursts. Thus a tubeless can flex
over an object, giving it a better impact resistance than a tube type one.
Personally, I feel that a tubeless tyre is more beneficial than a tube type tyre, but yet
many people feel that since a local puncturewalla cannot attend to a tubeless it may be a
bad proposition to use them. Generally it is quite simple and sometimes easier to repair a
tubeless tyre than a tube type one. Of course there still remains one important criterion
that the repairer must have proper tools and equipment to handle the same, which is
essential for tube-type tyres as well. I still maintain that utmost care and regular checks
should be carried out at regular intervals to get the best from your tyres. Secondly most
tyre companies worldwide do not recommend use of tube in tyres lower than 60 aspect
ratio. The other factor is the safety given by a tubeless may not be comparable with a one
using a tube.
2. THE TUBELESS REVOLUTION ?
What Makes A Tubeless Tyre? We Explain.
In this epistle we focus on the constructional details of a tubeless tyre which will
fundamentally help us as we motor along the tubeless highway.
It is tragic that we Indians are not the hardiest of adventurous souls who experiment and
adopt new ways to spice up their life, and also to make things easier on themselves.
Though tubeless tyres have been around since the mid 1950s, we only stumbled upon
them with the advent in the late 1990s! It's another matter that it needed a high-end
premium automobile to set things rolling on this count - a case repeated often enough
abroad as well - but now we need to see the same thought and product process filtering
through lower down the pecking order. Many car makers and tyre makers blamed bad
roads and a lack of education as reasons for not ushering in tubeless tyres but all that is
now changing. It better because our neighbours in the SAARC nations like Sri Lanka,
Bangladesh, Pakistan and Nepal have been running on tubeless tyres for over a decade, if
not more!
In place of the tube in a normal tyre, the tyre and the rim of the wheel form an air
container in a tubeless tyre. To 'seal in the air', in this tyre-rim compartment, the inner
wall of the tyre is throughly lined with an impermeable, air-tight membrane. The inner
liner of the tubeless tyre is constructed of halo-butyl/chlorobutyl and other materials. This
performs, in essence, the important chore of substantially reducing the permeation of air,
as compared to the natural rubber inner liner, a function of which is why we use a butyl
tube in a tubed tyre.
A tubeless tyre also comes with a soft rubber chaffer, distinct from a rubberised fabric
chaffer in a tubed tyre. This works as an all-round air seal between the tyre and rim.
As there is no tube, and, hence, no tube valve, a specialised valve is employed for
increasing/reducing the air pressure in a tubeless tyre. The valve (check out the line
drawing to see how it mounts) sits on the tyre rim and is ingeniously sealed by a large
high quality rubber seal which is easy to mount.
As you can see that the tube is integrated in the tyre construction, so to spead, you also
have less weight, helping handling engineers in the car companies realise the benefits of
low unsprung weight. If you drive a Toyota Qualis or a Mercedes-Benz C, E- or S-Class,
or even the stunning new Ford Mondeo, the benefits of the tubeless rubber they come
with would have passed you by, so good is the feeling.
3. THE TUBELESS REVOLUTION ?
From the cross-ply to the radial to the tubeless
In the days of yore the only Indian cars worth considering were the only cars available.
As an impressionable youngster who used to hang around car enthusiasts, I used to
always hear that this tyre is no good because it could do only around 20,000km before the
tread vanished. Tyre life over all else seemed to be the mantra of the everyday car user
and I remember even our family car, which used to be a Hillman Minx then, would
seemed to go on and on forever.
Things changed dramatically in 1980s with the advent of the Marutis and also the
ushering in of the radial revolution. Suddenly we started hearing things like grip and
steering responses and ride comfort and fuel efficiency and not just tyre life.
More than anything else, it was growing awareness levels among car users that saw many
veering towards the radial tyre. The compromise between comfort (radial deflection), and
steerability (sideways stiffness) was not possible with the traditional (read that as cross-
ply) tyre structure as with the radial ply tyre. A radial casing alone offers no improvement
but if it also comes with a reinforced belt structure it retains the high comfort factor of its
radial-ply nature with the added virtues of steering controllability.
Moreover, it allowed designers to adjust the two factors in relation to each other as
required for a particular type of car. In contrast to the radial, the cross-ply is now
comparatively limited as far further development is concerned, even in India. I qualify
this by suggesting this statement holds good for passenger car application tyres only.
Radials may be about 25 per cent costlier than similar sized cross-ply tyres but they may
give upto 8-0 per cent more mileage and also afford the other intangible benefits in
superior ride quality and better grip and control, factors which have become common-
speak even in India today.
With the advent of radials came the stylised looks as well. Of course this came thanks to
the wide squat rubber used by racing cars but automotive stylists were quick to pick these
cues and design them into their new automobiles. The designers wanted wheels of a
certain overall diameter but they wanted them to also accommodate the brake discs and
part of the hub carriers. This helped give us the lowered height-width ratio and even
though we have had low profile cross-ply tyres as well, the radial handles low profiles
infinitely better-just ask Ferrari or Mercedes-Benz or BMW or Porsche.
It was this battle for low profiles and great grip with better cornering stability which
brought the tubeless tyre to the fore. In the early days thanks to rubber compounds and
tyre constructions being at the technological levels prevailing then, the tubeless tyres took
some time perfecting. But once the virtues of lower unsprung weight, easy repairability,
better ride quality and many more factors which only magnified the radial tyre advantage
became apparent, the tubeless radial has gone on to capture market share in the developed
lands.
The tubeless movement is now making its advent in India getting off the ground with
makers like Goodyear with its Trinuum Tyre Tech. From the cross ply to the radial to the
tubeless, tyres have surely come a long way.
4.The Need for Speed - Case Study
The first case shows a tyre with its tread separated from its casing. Could this have been a
manufacturing defect? Yes, provided the tyre was not over six years old, as in this case.
The tyre was manufactured in 1994, but was sparingly used, thus the tread was not worn
out but the casing deteriorated and when subjected to speeds above 130kmph, literally
tore out in chunks. Thanks to radials, the owner was able to control the vehicle to a slow
stop.
The second case you will notice again the tyre has suffered a tread/belt separation. This
too can be attributed to a manufacturing defect. Unfortunately the owner had purchased
this imported tyre from a dealer who sold him a defective tyre. This is very clear from the
fact the specific markings, which give the authenticity of a tyre has been buffed off.
Secondly the speed rating of the tyre was 'S' (160kmph), while the vehicle was a
Mercedes, capable of being driven at speed of over 190kmph. We asked the owner to
replace them with a 'V' rated tyre, for safer driving.
Here we see a tyre, which may have suffered an impact before it entered the highway.
This tyre was a tubeless type but was fitted with a tube. Now the tyre must have absorbed
the impact but the tube did not.As the tyre flexed, heat generated within and after the near
completion of the journey the tube gave way rendering the tyre useless. The damage of
the tyre and tube can be clearly seen. Moreover the nature of impact is also visible at the
rim area.
The fourth case, I would like my readers to see how a nail penetration has caused this tyre
to fail and by the time the vehicle could be brought to a standstill the tyre was
ruined.Here again I would say that the owner has been lucky to use a radial, as although
his tyre was wrecked he was able to come back with his story safely to us.
In my last case we see a tyre which has more than 60,000km logged on it. The life of the
tyre was virtually over, as the tread depth had already reached its 'TWI' (Tread Wear
Indictor) marking or had only 1.6mm tread depth left. Yet the owner was reluctant to
replace his tyres and as luck would have it on his return after a weekend at Lonavala, the
tyres developed a belt distortion. The only solution for him was to replace the entire set.
5. Wheels - The Money Spinner
The first Grand Prix, which was held at Magny-Cours, France, in the year 1906,
presented a real challenge not only for automobile manufacturers but for tyre
manufacturers as well. Since the 1200km hot dusty course caused numerous punctures, it
put a strain on drivers as they had to replace tyres themselves, which was a painfully
laborious process. An advertisement of the time projected it to be as easy as child's play
but the truth was far from it. Thus Michelin's offer of the new technical innovation of
completely detachable wheels amazed spectators, specially the performance of Ferenic
Sziz who won the race at an average speed of over 101kmph on a Renault engined car.
The key to Sziz's victory could be attributed to the fact that he managed to change a tyre
in three minutes flat with these detachable wheels. Michelin also made history when out
of the 34 cars which started only 11 finished, in which the first, second, fifth, sixth and
eighth were all on these wheels.
Yet these wheels were a far cry from the wheels of today. Those days traditional carriage
wheels and wire-spoke steel wheels developed for the bicycle were alternatives available
for automobiles. The three types of modern wheels are of pressed steel, wire-spoke
wheels and light-alloy casting wheels. The pressed wheels are light, strong, stiff and
resistant to accidental damage. They require negligible maintenance and are only inferior
to alloy wheels on one count; they are heavier. Over 90 per cent vehicle manufacturers
use such wheels, as they are easy to produce and cheap to manufacture in large quantities.
Steel wheels are made from two pressings. The inset distance and rim profile are varied
to suit the car manufacturer's requirements. The flange profile, indicated by letters J, K,
JJ, JK, or B in the specification, is designed to comply with the tyre bead profile.
Though I have already written about problems caused by using an incorrect flange type as
well as the wrong width I repeat that it is of vital importance that correct width be
maintained in relation to the tyre size as this is the factor responsible for the handling
characteristics of a car. A rim too narrow in relation to the tyre width, for example, will
allow the tyre to distort excessively sideways under fast cornering. On the other hand,
unduly wide rims on an ordinary car tend to give rather a harsh ride because the sidewalls
have not enough curvature to make them flex over road irregularities.
The earliest type of wheels were of the wire-spoke variety. They were light yet strong as
they not only had to withstand the weight of the car but also forces of acceleration,
braking and cornering. Normally all wheels are subjected to extreme loads and stress
even in normal road use as during cornering they have to combat combined forces of
braking and acceleration. Thus all loads on the wheel are transmitted from the rim to the
hub by the spokes. These spokes were made of steel as they had to be stronger in tension
than in compression. Spokes individually have little resistance to bending stresses, so
they had to be laced in a complex crisscross pattern, ensuring that the load fed into a
wheel was evenly distributed among the adequate number of spokes, thus converting the
wheel to a tensile load similar to a pulling load rather than subjecting it to a pressing or
bending load.
Assembling a wire-spoke wheel is a skilled operation, as each spoke has to be
individually hooked at one end of the hub while its other end is pushed through a hole in
the wheel rim, where a tapered nut also called as a nipple is screwed down pulling the
spoke tight. If a spoke is too loose or too tight the rim that is relatively flimsy will distort.
This labour intensified manufacture could be justified in the early days when the
alternatives available were not so strong or light, but today such wheels are expensive
because of their complicated construction. Such wheels are traditionally associated with
vintage sport cars and racing cars, but strictly speaking have little justification today from
an engineering point of view. Moreover the pierced rim of a wire wheel makes it
impossible to fit tubeless tyres as they require airtight rims.
For steering control the wheels must be of rigid construction. With a pressed steel rim the
'spoke' portion is usually of near-conical shape for extra lateral stiffness. This proved to
be of great disadvantage in the earlier designs as the disc had to be liberally perforated to
allow the passage of cooling air to the brake drums, thus by piercing holes in the disc
weakened it. The wheel manufacturers turned this to an advantage by using a slightly
more expensive technique. The holes were swaged, which means that their edges were
turned smoothly inwards, thus actually increasing the strength of the wheels. Today all
wheel manufacturers use swaging technique as standard on their pressed wheels.
The third variant is light-alloy casting wheels which are generally meant to impress and
essential quality and advantage is ignored. Alloys have the main advantage of being
lighter than the other types of rims, but with use of a combination of aluminum and
magnesium alloys have a thicker flange section, which promotes stiffness and distribute
stresses over a wider area. This allows wider tyres to be fitted, which improves road-
holding ability especially on corners and is one of the main reasons for their use on some
sport cars. Light alloys are also good conductors of heat and thus allow heat generated by
brakes and tyres to disperse quicker. They react badly to salt spray and must be checked
regularly for corrosion. I shall focus on alloy wheels in future but now dwell on how
wheels are mounted and problems regarding the same. The most common type of wheel
mounting consists of either four or five threaded studs equally spaced in a circle around
the hub flange. These studs pass through holes in the wheel, which is secured by nuts
screwed on to the studs. The holes through which the studs pass are not simply pierced
through but the area around each hole is pressed out to form a tapered seating which
ensures a corresponding tight fit. Each wheel sits on a position which is centrally located
on the hub and is called the pitch circle diameter (PCD) of the wheel. The hub diameter is
known as the bore diameter.
6. THE TUBELESS REVOLUTION ?
Advantages of a Tubeless Tyre over Conventional Tube Tyre
OVERDRIVE advocates the use of tubeless tyres. Why? How much importance do we
place on the tyres we use in our vehicles? Where is tyre technology is to in the future? It
is essential for vehicle users to be aware of the advantages of tubeless tyres compared to
conventional tube tyres.
So what exactly are the advantages? The primary advantage of a tubeless tyre is in
internal construction and materials used. A tubed tyre is vulnerable to friction and heat
generated between the tube and the inner surface of the tube which reduces life of the
tube. In a tubeless tyre the inner layer of the tyre is the tube itself. This layer is made of a
material like halo-butyl/chlorobutyl which is basically resistant to heat and reduces
permeation of air.
The weight of the tube inside a tyre adds to the unsprung weight affecting handling
characteristics and overall performance. The lack of a tube reduces unsprung weight and
improves dynamic ability. The lack of a tube also reduces rolling resistance caused by
friction between the tyre and tube. The lower rolling resistance, lesser weight and the
tubeless tyre's capability to uniformly retain air improve fuel efficiency
Another important advantage from a safety point of view takes care of a problem none of
us have control over: punctures! Ever experienced a high-speed blowout? There have
been a number of gruesome high-speed fatalities on the Mumbai-Pune expressway
caused by tyre blowouts.
At speeds in excess of 100kmph high temperatures are generated. These high
temperatures expand (in some cases this tube is over-inflated too which only aggravates
the situation) the tube and a sudden sharp penetration at high speed causes the tube to
burst very easily. The air expelled at high pressure forces its way out of the tyre from
around the rim and the tube valve hole. In some cases the pressure exerted by this
escaping air is strong enough to rip open the tyre. A burst tyre causes a sudden loss in
traction which is sufficient to throw the vehicle off course violently.
In a tubeless tyre penetrations into the tyre are sealed off by the rubber itself. As a result,
leakage of air does not take place and if it does, it is minimal. Over-inflation can still
cause grievous harm but the hazards from punctures in a tubeless tyre are greatly
reduced. In case of a total loss of air inside the tyre, it is likely that the bead will collapse
inside the rim-well rather than come off it.
Other tube troubles include ballooning, open splice, spurious tubes, pinholes, tube
mounting damage and finally the cost of a tube and its maintenance, all of which are
avoided with tubeless tyres.
Tubeless tyres present a very good case for themselves. They are a welcome foot forward
in tyre technology that the world has accepted decades ago.?
7. Conclusion:-
By using tubeless tyre technology which is invented by engineer Paul Weeks litch field in
1903. We can reduce friction and heat generation which is developed in conventional
tyres between the tube and inner surface of the tube. By using tubeless tyre technology
we can also reduce unsprung weight and improves dynamic ability. It also reduces rolling
resistance cause by friction in the tube and tyre. Using this technology we can improve
fuel efficiency and also reduces puncture as in tubeless tyre penetration into the tyre are
sealed of the rubber is self. As a result leakage of air does not take place and if it does it
is minimal. So tubeless tyre present a very good case for themselves. They are a welcome
foot forward in tyre technology that the world has accepted decades ago.
References :-
? Sujan Choudhari, ?Tubeless Tyre Technology?
? Adil Jal Darukhanawala, ?Tubeless Tyre Technology?
Website :-
? http://www.google.com
Reference: http://seminarprojects.com/Thread-tubeless-tyre-technolegy#ixzz2fubQOETJ