ts ¡ECEx Gert¡f¡cateof Gonformity

INTERNATIONAL ELECTROTECHNICAL COMMISSIONIEG Certification Scheme for Explosive Atmospheres

for rules and details of the IECEx Scheme visit www.lecex com

Certificate No.:

Status:

Date of lssue:

Applicant:

IECEx SIR 12.0048X

Gurrent

2016-11-03

Certificate history:

lssue No I (2016-1 1-3)lssue No. I (2016-10-

1e)lssue No 7 \2015-114)lssue No.6 (2015-9-16)lssue No. 5 (2014-8-14)lssue No. 4 (2013-6-12)lssue No 3 (2013-1-25)lssue No. 2 (2012-12-3)lssue No. 1 (2012-11-7)lssue No 0 (2012-8-23t

Page 't of 4

Certification Manager

issue No.:9

Rotork Controls LimitedBrassmill LaneBath BA1 3JQUnited Kingdom

Equipment:Optional accessory:

lQ Range of Electric Valve Actuators

Type of Protection: Flameproof, lncreased Safety and Dust Protection by Enclosure

Marking:

Approved for lssue on behalf of the IECEx N JonesCeftification Body:

Ex d1 IIC T4 Gb(1 "e" added on versions with ¡ncreased safety terminal enclosure)Ex tb IIIC T120oC Db IP6B/IP66, (Only IP64 is endorsed by Sira on this cert¡ficate)f¿ = (-#oÇz to +#ofa (2 down to -50oC, 3 up to 70oC)The IqH*x models are not available as a low temperature version (below -20oC)

Date: Lo,6-ll - o3

1. This certificate and schedule may only be reproduced in full2. This certificate is not transferable and remains the property of the issuing body.

3. The Status and authenticity of this certif¡cate may be verified by visiting the Official IECEx Website.

Position:

Signature:(for printed version)

CertifÌcate issued by:SIRA Certification Service

CSA GrouPUnit 6, Hawarden lndustrial Park

Hawarden, Deeside, CH5 3USUnited Kingdom

PP Plu"//

slratcsA0roup

cËRlrFtcATroN

ts IECEx Gert¡f¡cateof Conformity

lssue No : 9

Page 2 oÍ 4

Manufacturer: Rotork Controls LimitedBrassmill LaneBath BA1 3JQUnited Kingdom

Additional Manufacturing location(s):

Rotork Controls lnc675 Mile Crossing BlvdRochesterNew York 14624Un¡ted States of America

This certifìcate is issued as verification that a sample(s), representative of production, was assessed and tested and

found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products

covered by tniicertificate, was assessed and found to comply with the IECEx Quality system req_uirements. This

certificateis granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operationel Documents

as amended.

STANDARDS:The electrical apparatus and any acceptable variations to it specifìed in the schedule of this certificate and the identified

documents, was found to comply with the following standards:

Certificate No

Date of lssue:

IEC 60079-0 : 2011Edition: 6.0

IEC 60079-1 :2007-04Edition: 6

IEC 60079-31 : 2008Edition: 't

IEC 60079-7 : 2006-07Edition: 4

Test Report:GB/Sl Ri/ExTR 1 2.021 4l0O

GB/SIR/ExTR12 O293l0OGB/Sl F/ExTR1 4.01 93/00GB/Sl R/ExTR1 6.0266/00

QualiW Assessment Report:

GB/SrFyQAR06.0023/03

G B/Sl R/ExTR 1 2.027 51 00GBiSIR/ExTR1 3.001 3/00GB/SlFfExTRlS 0240100

GB/SlR/ExTR12 0276100GB/SIR/ExTRl3 0171/00GBiSIR/ExTRl 5.0306/00

IECEx SIR 12.0048X

201 6-1 1 -03

Explosive atmospheres - Part 0: General requirements

Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"

Explosive atmospheres - Part 31 : Equipment dust ignition protection by enclosure 't'

Explosive atmospheres - Pa¡I7: Equipment protection by increased safety "e"

This Ceftificate does not indicate compliance with electrical safety and performance requirements other than those

expressly included in the Standards listed above.

TEST & ASSESSMENT REPORTS:A sampte(s) of the equipment tisted has successfutly met the examination and test requirements as recorded in

GB/S|R/QARo7 0003t02

e IECEx Gert¡f¡cateof Conformity

Certificate No.

Date of lssue:

IECEx SIR 12.0048X

20t 6-t I -03 lssue No.: 9

Page 3 of 4

Schedule

EQUIPMENT:Equipment and sysfems covered by this ceftificate are as follows:

c Valve Actuators an worm gearcase e and drive bush,an external handwheel and de-clutch mechanism. Attached to the gearcase is a motor enclosure, an electricalcontrol enclosure and a terminal enclosure. All electrical enclosures are designed to satisfy the requirements forflameproof equipment. ln addition, the term¡nal enclosure is designed to satisfy the requirements for increasedsafety, providing an alternative method of protection for the field wiring facilities. The lQ Electric Actuator comprises a

range ofelectric actuators based upon various gearcase sizes.Refer to the Annexe for additional informationFor Conditions of Certification and Conditions of Manufacture refer to the Annexe

CONDITIONS OF CERTIFICATION: YES as shown below:

Refer to the Annexe

ts IECEx Gert¡f¡cateof Gonformity

Certificate No

Date of lssue:

IECEx SIR 12.0048X

20t 6-1 I -03 lssue No.: 9

Page 4 o'Í 4

DETAILS OF CERTIFICATE CHANGES (for issues I and above)r

lssue I to lssue 7 - for changes refer to Issue 7I lssue I - this lssue introduced the following changes:

Various amendments to the approval documents, which includeCorrection of PLAD1346 issue number from 06 to 7.

Addition of the terminal bung retaining ring Type 38377CH.Addition of an alternative design for the handwheel cover seal for all sizesAlternative internal earth arrangement.Alternative low temperature bearings added.Alternative wormshafts & wormwheels added

lssue 9 - this lssue introduced the following change:1 The marking was clarified

Annex: IECEx SIR 12.0048X Annexe lssue 9 pdf

Annexe to:

Applicant:

Apparatus:

slraIECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

csAGroup

CERTIFICATION

The motor enclosure is formed by a cover which connects to the gearcase by means of a spigoted flamepathjoint and is secured by four M8 capscrews. The rotary output from the motor transfers to the gearcase by means

of a shaft supported by rolling element bearings and a cylindrical brass bushing forming its flamepath. Electrical

services to the motor are supplied from the electrical enclosure via a potted, motor loom transfer bush,

Thermal protection devices are installed within the motor windings. There is a facility to override these devices

should the user find it necessary.

NOTE: The overriding of the temperature classification thermal protection devices is æ-t coveredby the scope of this ceftificate.

The electrical enclosure is formed by a cover which connects to the gearcase by means of a spigoted flamepathjoint and is secured by four M8 capscrews. The electrical enclosure contains monitoring and control circuitry,

which senses and controls the position of the output shaft; it also contains a back-up battery facility, contained

within an internal battery pocket, accessed externally via the battery pocket plug.The permitted battery types

are: Ultralife PP3 type U9VL/U9VL-J-P, SAFTto Rotork part no 95-462, Tadiran/Sonneschein to Rotork part Nog5-6t4, in each case the battery is is protected by an in-line fuse (permitted fuse types are Quick Blow Bussman

5500, 100m4, Quick Blow Littlefuse2L7,100 mA). At one end of the electrical enclosure a window is provided

to allow the obseruation of an internal LCD device. The window is manufactured from toughened glass and

potted into the electrical cover, An encoder shaft exits the electrical enclosure via a cylindrical brass bushing,

flamepaths being between the bushing and the gearcase and between the shaft and the bushing. The encoder

shaft has a shoulder that is held against the shroud by a circlip'

The terminal enclosure connects to the electrical enclosure via the gearcase, their volumes being separated by

a flameproof terminal bung. The flameproof terminal bung comprises of moulded plastic main body throughwhich passes a number of terminals which are sealed in place with a potting compound. The terminal bung is

secured in position by means of a circlip. The terminal enclosure provides all electrical field wiring terminationsat the terminal bung. The above flameproof terminal bung may be replaced with a non-flameproof terminal bung,

in which case the electrical and terminal compartments are considered as one flameproof enclosure. This

configuration cannot be applied to the variants that incorporate increased safety terminal facilities. Cable entryfacilities are provided in the form of three or four threaded entries. The terminal enclosure is closed by means

of a lid, which connects to the gearcase by means of a tapered spigot joint and is secured by four M8 capscrews.

The terminal compartment is common to all sizes.

All external fasteners are stainless steel, grade A4-80 socket cap head screws.

The following gearcase/motor options are covered:

IQ Gearcase/Motor Configurations 3 phase, up to 690 V rms

Size 1Gearcase size 1

One motor enclosure, four pole motors, two stator lengthsDesignated IQ10, 12 & 18.

Size 2Gearcase size 2One motor enclosure, with either two or four pole motors, six stator lengthsDesignated IQ19, 20 & 25.

Date: O3 November 2016

Sira Gertification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (0) 1244 670900Fax: +44 (0) 1244681330Email: ukinfo@csagrouo.oroWeb: www.csagrououk.org

Form 9530 Issue 1

Page 1 of 8

Annexe to:

Applicant:

Apparatus:

IECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

sTÍA CSAGroup

CERTIFICATION

Size 3Gearcase size 3

One motor enclosure, with either two or four pole motors, one stator length

Designated IQ35.

Size 5Gearcase size 5Motor OptionsThree Motor enclosures:One motor enclosure with two or four pole motor, one stator lengthDesignated IQ40One motor enclosure with either two or four pole motors, five stator lengthsDesignated IQ 70, 90, 95.One motor enclosure with a two pole motor, one stator lengthDesignated IQ 91

Design Options

Single phase motor option - Actuator sizes 1, 2 and 3

Actuator Motor4 pole 110 to 240 Vrms + 100/oIQS12

ros20 4 pole 110 to 240 Vrms t l0o/o

IOS35 214 pole 110 to 240 Vrms x L0o/o

Different motor options (as can be seen above) as well as the necessary alternative control equipment within the

electrical enclosure.

Modulating motor control option for three phase motors - Actuator sizes 1, 2 and 3.

The reversing contactor has been replaced with a solid state starter module, utilising thyristor drives and their

associated control electronics, designated:

IQM10, IQM12, IQM20, IQM25, IQM3514

Deep Terminal Cover Option - All actuator sizes

The deep terminal cover allows the installation of a PCB for various network disconnect applications or a wireless

network PCB and associated external aerial enclosure, on Ex d versions. The deep cover is provided with threaded

entry points.

Intumescento coating option to the exterior of the actuators for fire proofing purposes.

The application of an outer, Intumescentofire retardant coating can be applied to allsizes.

Lightning suppression module option - All actuator sizesApplies to terminal enclosures that are marked 'Ex d' only; it allows the inclusion of a lightning suppression

module secured to the inner face of the existing terminal lid.

IQH variant option - Ambient temperature range -2OoC to +7OoCThe following high speed actuator types have been introduced:

IQH20, IQH25, IQH35, IQH40

Sira Gertification ServiceDate: O3 November 2016 Unit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (01 1244 670900Fax: +44 (0) 1244 681330Email: ukinfo@csagroup.orgWeb: wvuw.csagroupuk.org

Form 953O Issue I

Page 2 of 8

Annexe to:

Applicant:

Apparatus:

IECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

srraT

CERTIFICATION

csAGroup

CONDITIONS of CERTIFICATION

i. This equipment shall be positioned such that risk of impact to the window is low.

ii. This equipment included some external non-metallic pafts, including the outer protective coating. Cleaning

shall only be carried out with a damp cloth.

iii. In accordance with clause 5.1 of IEC 60079-t, the critical dimensions of the flamepaths are:

Dimension mSizes 5Sizes 1 2and3

LenqthLenqth GaÞGap

Flamepath

0,15 25.000.15 25.0Gearcase / Motor Cover49.7535.0 0.000.0sGearcase / Wormshaft shroud

26.O 0.25 49.750.24Wormshaft shroud / Wormshaft27.000.1 15 27.0 0.1 15Gea Terminal Bu27.0027.0 0,150.15Gearcase / Terminal Cover

0.15 26.000.15 26.0Electrical Cover27.0027.O 0.080.08Encoder Shaft Encoder Shaft

o.o7 25.000.07 25.0Gearcase / Encoder Shaft Bush33.2529.0 0.150,15Gearcase Loom Bush

0.15 27.00.15 27.0Gearcase / Deep Terminal Cover26.00.15Gearcase / Short Electrical Cover

Date: O3 November 2016

Sira Gertification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CH5 3US, United KingdomTel: +44 (0) 1244670900Fax: +44 (0) 1244681330Email: ukinfo@csagroup.orgWeb: www.csagroupuk.org

Form 9530 Issue 1

Page 3 of 8

Annexe to:

Applicant:

Apparatus:

IECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

srra CSAGroup

CERTIFICATION

CONDITIONS OF MANUFACTURE

When the termination facility is to be designed as'Ex e', the following electrical strength tests shall be

applied to the termination facilities for at least 60 s and no more than 63 s as required by clause 6.1 of IEC

60079-7.

Alternatively, the following electrical strength tests may be applied to the termination facilities for at least

100 ms as required by clause 7.1 of IEC/EN 60079-7'

Test VoltageTest Voltaqe Aoolied Between3000 V nusThree phase terminations/case3000 V n¡¡sThree ohase terminations and low voltaqe terminations1800 V nmsLow terminations and case

Each enclosure shall be subjected to a routine overpressure test in accordance with the tables below for

the design option and ambient temperature range stated. In all cases the pressure shall be maintained for

at leastlO s as required by clause 16 of IEC 60079-1:2007, There shall be no permanent deformation or

damage to the enclosure.

Routine overpressure tests Tamb -20oC to +7OoC

2500 V nrqsterminationThree2500 vse terminations and low e terminationsThree1500 V nNsterminations and caseLow

Test Pressurelbf lin2bar

Equipment

Gearcase - Terminal Fitted

Size 120.63 299.L5Gearcase/Electrical Compartment Aluminium Alloy to 851490. Grade: LM25M

eouivalent)

(or

20.63 299.15Terminal Crastin20.63 299.15Motor Loom Bush Robnor PX700/BK20.63 299.15to ASTMShort Electrical Cover Aluminium Grade:4360 or

Size 2434.9029.99Gearcase/Electrical Compartment Aluminium Alloy to 851490. Grade: LM25M (or

equivalent)29.99 434.90Terminal Crastin29.99 434.90Electrical Cover Aluminium Al to ASTM 885 Grade: 4360 or29.99 434.90Long Electrical Cover Aluminium Alloy to 851490. Grade: LM25TF (Heat Treated)(or

29.99 434.90Motor Loom Bush Robnor434.9029.99Short Electrical Cover Aluminium to ASTM 885 Grade: A360 or

Size 320.00 290.01Gearcase/Electrical Compartment Aluminium Alloy to 851490. Grade: LM25M (or

290.0120.00Terminal Bu Crastin ST83OFRUV290.0120.00Motor Loom Bush Robnor

20.00 290.00to ASTMShort Electrical Cover Aluminium Grade: A360 or

Size 5

Date: O3 November 2016

Sira Certification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (0) 1244 670900Fax: +44 (0\ 1244 681330Email: Ukinfo(Ocsagroup.orgWeb: vvr¡w.csagrouÞuk.org

Form 9530 Issue 1

Page 4 of 8

Annexe to:

Applicant:

Apparatus:

slraI

CERTIFICATION

IECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

csAGroup

Test Pressurebar bf lin2

Equipment

Gearcase - Terminal Fitted240.8416.61Terminal bung Crastin ST83OFRUV/ Robnor PX700/BK (tested from either terminal or

flameproof side)Gearcase - Fla Terminal NOT Fitted

Size 227.35 396.61Gearcase/Electrical-Terminal Comp Aluminium Alloy to 851490' Grade: LM25M (or

eouivalent)27.35 396.61Terminal Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)27.35 396.61Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)27.35 396.61Long Electrical Cover Aluminium Alloy to 8S1490. Grade: LM25TF (Heat

TreatedXor equivalent)27.35 396.61Motor Loom Bush Robnor PX700/BK27.35 396.61Short Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

Size 331.68 459.49Gearcase/Electical-Terminal Comp Aluminium Alloy to 851490' Grade: LM25M (or

31.68 459.49to ASTMTerminal Cover Aluminium Grade:4360 or459.4931.68Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

31.68 459.49Long Electrical Cover Aluminium Alloy to 8S1490. Grade: LM25TF (Heat

or UIVA

31.68 459.49Motor Loom Bush Robnor459.4931.68to ASTMShort Electrical Cover Aluminium Grade: 4360 or

Size 540.07 581.10Gearcase/Electrical-Terminal Compartment Aluminium Alloy to 851490. Grade: LM25M

lor eouivalent)581.1040.07Terminal Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

40.07 581.10Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)40.07 581.10ElecFical Cover Aluminium Alloy to 851490. Grade: LM25TF (Heat Treated)(orLong

equivalent)581.1040.07Motor Loom Bush Robnor PX700/BK (size 5)

Motor Endosure

Size 5236.27t6.29Gearcase/Motor Compaftment IQ 70190/95 Aluminium Alloy to 851490. Grade: LM25M

lor eouivalent)LT.24 t62.95IO 40 Motor Cover Aluminium Alloy to 851490. Grade: LM25M (or equivalent)t6.29 236.27Motor Cover Aluminium to 851490. Grade: LM25M or

Date: 03 November 2016

Sira Certification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (o) 1244 670900Fax: +44 (0) 1244681330Email: ukinfo@csagrouo.orgWeb: vuvw.csagrououk.org

Form 9530 Issue 1

Page 5 of 8

Annexe to:

Applicant:

Apparatus:

srraIECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

CSAGroup

CERTIFICATION

Routine overpressure tests Tamb (below -20oC to -50oC) to +70oC

Date: O3 November 2016

Sira Certification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (0) 1244 670900Fax: +44 (0\ 1244 681330Email: ukinfo@csagroup.oroWeb: wr,vw.csagroupuk.org

Test Pressurebar lbf/inz

Equipment

Terminal Enclosure (all sizes)18.09 262.30Terminal bung Crastin STB30FRUV/Robnor PX7OO/BK(can be tested from either

terminal or flameproof side)All sizes with Deep Terminal cover fittedGearcasefferminal Compartment Aluminium Alloy to 851490. Grade: LM25M (oreouivalent)

20.87 302.63

20.87 302.63Deep cover Aluminium Alloy Sandcast (heat treated) LM25TF BS 1490:1988 (orequivalent)

20.87 302.63Certified Terminal Bunq Crastin ST83OFRUV/Robnor PX700/BK

Gearcase - Flameproof Terminal Bunq Fitted

Size 1Gearcase/Electrical Compaftment Aluminium Alloy to 851490. Gnde: LM25M (oreouivalentl

25.10 363.98

25.10 363.98Terminal Bunq Crastin ST830FRUV/Robnor PX700/BK

Lonq Electrical Cover Aluminium Allov to ASTM 885, Grade: A360 (or equivalent) 25.10 363.9825.10 363.98Long Electrical Cover Aluminium Alloy to to 851490. Grade: LM25TF (Heat Treated)(or

equivalent)25.10 363.98Motor Loom Bush Robnor PX700/BK25.10 363.98Short Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

Size 229.99 434.90Gearcase/Electrical Compartment Aluminium Alloy to 851490. Grade: LM25M (or

equivalent)29.99 434.90Terminal Bunq Crasbn ST830FRUV/Robnor PX700/BK

29.99 434.90Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)29.99 434.90Long Electical Cover Aluminium Alloy to 851490. Grade: LM25TF (Heat Treated)(or

equivalent)Motor Loom Bush Robnor PX700/BK 29.99 434.90

29.99 434.90Short Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

Size 330.21 438.L7Gearcase/Electrical Compaftment Aluminium Alloy to 851490. Gnde: LM25M (or

equivalent)30.2r 438.r7Terminal Bunq Crastin ST83OFRUV/Robnor PX700/BK

30.2r 438.r7Lonq Electrical cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)30.21 438.r7Long Electical Cover Aluminium Alloy to 851490. Grade: LM25TF (Heat Treated)(or

eouivalent)30.21 438.t7Motor Loom Bush Robnor PX700/BK

30.21 438.r7Short Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

Size 525.32 367.24Gearcase/Electrical Compartment Aluminium Alloy to 851490. Grade: LM25M

(or equivalent)Terminal bunq Crastin ST830FRUV/ Robnor PX700/BK 25.32 367.24

25.32 367.24Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)367.24Long Electrical Cover Aluminium Alloy to 851490. Grade: LM25TF (Heat Treated)(or

eouivalent)

25.32

25.32 367.24Motor Loom Bush Robnor PX700/BK

Form 9530 Issue 1

Page 6 of B

Annexe to:

Applicant:

Apparatus:

srraIECEx SIR 12.O048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

csAGroup

CERTIFICATION

Gearcase - Terminal Fitted

Size 122.95 332.87Gearcase/Electric¿l-Terminal Comp Aluminium Alloy to 851490. Grade: LM25M (or

22.95 332.87Lonq Electrical Cover Aluminium Alloy to ASTM 885, Grade: A360 (or equivalent)22.95 332.87Motor Loom Bush Robnor22.95 332.87to ASTMShort Electrical Cover Aluminium Grade:4360 or

Size 230.89 447.96Gearcase/Electrical- Term Comp Aluminium Alloy to BS1490. Grade: LM25M (or

47.9630.89to ASTMTerminal Cover Aluminium Al Grade:4360 or30.89 447.96Grade: 4360Electrical Cover Aluminium to ASTM30.89 447.96Long Electical Cover Aluminium Alloy to 851490. Grcde: LM25TF (Heat Treated)(or

447.9630.89Motor Loom Bush Robnor30.89 447.96Short ElecFical Cover Aluminium tO ASTÏT4 Grade:4360 or

Size 331.68 459.49Gearcase/ElecÍical-Terminal Comp Aluminium Alloy to 851490' Grade: LM25M (or

eouivalent)31.68 459.49Terminal Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)31.68 459.49Grade: 4360 (or equivalent)Lonq Electrical Cover Aluminium Alloy to ASTM 885,31.68 459.49Long Elecúical Cover Aluminium Alloy to 851490' Grade: LM25TF (Heat Treated)(or

31.68 459.49Motor Loom Bush Robnor PVO0/BK31,68 459.49Grade: 4360 (or equivalent)Shoft Electrical Cover Aluminium Alloy to ASTM 885,

Size 536.23 525.4rGearcase/Electrical-Terminal Compartment Aluminium Alloy to 851490. Grade: LM25M

lor eouivalent)36.23 s25.4tTerminalCover Aluminium Alloy to ASTM 885, Grade: A360 (or equivalent)36.23 525.4rElectrical Cover Alu mini um to ASTM Grade: 4360 or36.23 525.4rLong Electrical Cover Aluminium Alloy to to 851490. Grade: LM25TF (Heat Treated)(or

36.23 525.4LMotor Loom Bush Robnor

Date: 03 November 2016

Sira Gertification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (0) 1244 670900Fax: +44 (0) 1244 681330Email: ukinfo@csagroup.orgWeb: www.csagroupuk.org

Form 953O Issue 1

Page 7 of 8

Annexe to:

Applicant:

Apparatus:

srraIECEx SIR 12.0048X Issue 9

Rotork Controls

IQ Range of Electric Valve Actuators

csAGroup

CERTIFICATION

Motors Endosures

Size 223.5t 340.92Gearcase/Motor Comp Aluminium Alloy to 851490. Grade: LM25M (or equivalent)23.5t 340.92Motor Cover Aluminium Alloy to ASTM 885, Grade: A360 (or equivalent)23.5r 340.92Motor Cover Aluminium Alloy to 851490. Grade: LM25M (or equivalent)

Size 3276.3019.05Motor Cover Aluminium Alloy to ASTM 885, Grade: 4360 (or equivalent)

Size 5292.4020.16Gearcase/Motor Compartment IQ40 Aluminium Alloy to 851490' Grade: LM25M

lor eouivalent)20.16 292.40Motor Loom Bush (IQ 40 motor side) Robnor PX700/BK (size 5)20.t6 292.40Gearcase/Motor Compartment IQ 70190195 Aluminium Alloy to 851490. Grade:

LM25M lor eouivalent)13.88 20t.24Gearcase/Motor Compartment IQ 91 Aluminium Alloy to 851490' Grade: LM25M

(or equivalent)20.16 292.40IQ 40 Motor Cover Aluminium Alloy to 851490. Grade: LM25M (or equivalent)20.16 292.40lQ 70190195 Motor Cover Aluminium Alloy to 851490' Grade: LM25M (or

eouivalent)

Date: 03 November 2016

Sira Certification ServiceUnit 6 Hawarden lndustrial Park,

Hawarden, CHs 3US, United KingdomTel: +44 (0) 1244670900Fax: +44 (O) 1244681330Email: ukinfo(Ocsagroup.orgWeb: www.csagroupuk.org

Form 9530 lssue 1

Page 8 of 8