tour 9 axes okuma macturn250_350
TRANSCRIPT
MACTURN250/350
Multifunction Machines
MACTURN250/350Multifunction machines
1 2
Lower turretHighly efficient simultaneous 4-axes machining
Roller guideHighly rigid roller guides for all axesBall guide ratio: 2 times more
ATC turretTurning: 2.5 mm2 (0.0039 in.2)(actuals)
Milling: 68 cm3/min (4.15 in.3/min)(actuals)(MACTURN250、S45C)
Roundness: 0.3 µm (11.81 µin.)(actuals)
2nd-operation spindle Motor output 7.5/5.5 kW (10/7.5 hp)
(MACTURN250)
11/7.5 kW (15/10 hp)(MACTURN350)
Powerful
Accurate
3 4
9-axis control multifunction MacTurns give you 120% satisfaction
Wider area
Y-axis travelY-axis travel 160 mm (6.30 in.) (MACTURN250)
190 mm (7.48 in.) (MACTURN350)
Highly efficient
V12 lower turretHighly efficient, simultaneous 4-axismachining with upper and lower turrets
MACTURN250/350
Indexing angle: 1 degree (standard)
B-axis for slope workEasier setups using the pulse handle tomanually feed the B-axis.
Integrated operations
2nd-operation spindle2nd-operation spindle enables 1 or 2 integratedoperations (front/back turning, live tool machining)
Long untended operations
ATC magazineThis is an NC automatic tool changer.With the magazine on the saddle, toolchanges can be done anywhere.
210°�
C1
W
XA
ZB
YB
XB
ZAC2
5
Highly accurate machining
Roundness 0.3 µm (11.81 µin.)
Workpiece material BSBSpindle speed 3,000 min-1
Surface roughness 0.4 µm (15.75 µin.)(blade edge uniformity)Workpiece material BSBSpindle speed 2,500 min-1
Roundness: 0.3 µm (11.81 µin.)Center method: LSCFilter: 50 U/R(2CR)
Magnification: x 5000Data No. 13
(actual value) (actual value)
Cross section curve(Longitudinal magnification: x 5,000.00 Lateral magnification: x 50.00)
Cross section curve(Longitudinal magnification: x 5,000.00 Lateral magnification: x 50.00)
8
Powerful milling example
MACTURN250/350(Workpiece material: S45C)
Face milling ø80 face milling (4-blade)(ø3.15) Cutting width 59.5 mm (2.34 in.)
Cutting depth 1.6 mm (0.06 in.)Feedrate 0.3 mm/rev. (0.01 ipr)Metal removal 68 cm3/min (4.15 in.3/min)
End milling ø20 (4-flute)Cutting depth 10 mm (0.39 in.)Feedrate 0.1 mm/rev. (0.004 ipr)
Tapping M16 P2
High-capacity live-tool machiningThe M-spindle motor provides full-power from the low to the high speed range for robust live-tool machining.
Powerful 2nd-operation spindleThe 2nd-operation spindle also has the extra power needed for complete primary/secondary operations.
2nd-operation spindle example
MACTURN250/350(Workpiece material: S45C)
Heavy-dutycutting
• M-tool motor�MACTURN250/350VAC 7.5/5.5/3.7 kW (10/7.5/5 hp)(5 min/20 min/cont)
10�(14)
20010050 300 500 10001100 6000
2000 5000 10000 20000
5�(7)
3�(4)2�
(3)
1�(1)
0.5�(0.7)
0.3�(0.4)
100�(74)65.1N・m(48ft-lbf)
5.5kW5.5kW(2020分)(20min20min)�
3.7kW3.7kW(連続連続)(cont.cont.)�
47.7N・m(35ft-lbf)
32.1N・m�(24ft-lbf)
50�(37)
30
20
10�(7)
5�(4)
3(2)
6,000 min-1
20050 10001200
3000 5000 1000012000
12,000 min-1 (Optional)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
5(7)
10(14)
Spindle speed, min-1Spindle speed, min-1
3(4)
2(3)
1(1)
0.5(0.7)
0.2(0.4)
100(74)7.5kW(10hp)(5min)
5.5kW(7.5hp)(20min)
3.7kW(5hp)(cont.)50(37)
10(7)
5(4)
59.7N•m(43.99ft-lbf)(5min)
23.9N•m(17.61ft-lbf)(5min)
43.8N•m(32.28ft-lbf)(20min)
17.5N•m(12.90ft-lbf)(20min)
29.5N•m(21.75ft-lbf)(Cont.)
11.8N•m(8.70ft-lbf)(Cont.)
7.5kW(10hp)(5min)
5.5kW(7.5hp)(20min)
3.7kW(5hp)(cont.)
30 3850 100 200 300 500 1000 2000 60001
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
MACTURN250-WVAC 7.5/5.5 kW (10/7.5 hp)(20 min/cont)6,000min-1 spec
MACTURN250-W/350-WVAC 11/7.5 kW (15/10 hp)(20 min/cont)6,000min-1 spec
MACTURN350-WVAC 15/11/7.5 kW(5 min/20 min/cont)5,000 min-1 specφ100 (φ3.94) big-bore spindle
MACTURN350-WVAC 11/7.5 kW (20 min/cont)5,000 min-1 specφ100 (φ3.94) big-bore spindle
30 50 100 1000500300200 6000200038
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
161.6 N・m(119ft-lbf)
110.2 N・m(81ft-lbf) 11 kW(15hp)(20 min)
7.5 kW(10hp)(cont.)100.0 N・m(74ft-lbf)
68.2 N・m(50ft-lbf)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
1000(737)
30 50 100 1000500
600 1400
300200 6000200045
1(1)
0.5
0.3
0.2
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
119.3 N・m(12.18ft-lbf)175.0 N・m(17.86ft-lbf)
102.3 N・m(10.44ft-lbf) 11 kW(20 min)
7.5 kW(cont.)
15 kW(5 min)
75.0 N・m(7.65ft-lbf)51.1 N・m(5.22ft-lbf)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
30 50 100 1000500
650 1050
300200 6000200045
1(1)
0.5
0.3
0.2
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
110.1 N・m(11.24ft-lbf)
161.5 N・m(16.48ft-lbf)11 kW(20 min)
7.5 kW(cont.)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1 Spindle speed, min-1 Spindle speed, min-1
159.2 N•m(117ft-lbf)116.7 N•m(86ft-lbf)
68.2N•m(50ft-lbf)50.0 N•m(37ft-lbf)
7.5 kW(10hp)(20 min)
5.5 kW(7.5hp)(cont.)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
1000(737)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
•OD cutting 1.5 mm2 (0.002 in.2)Cutting speed 100 m/min (328 fpm)Cutting depth 5 mm (0.20 in.)Feedrate 0.3 mm/rev (0.01 ipr)
�
15
Access MACTURN production support tool via IT Plaza
Creating new techniques by transferring and sharing techniques and expertise to
produce quality products.
Efficiency improved from the pre-operation stage!
ADMAC-Parts Turning
Passing on successful techniques
KCMAC Bridge to customersKnowledge Creation for Machining
Okuma makes all information required to produce
quality products openly available, including clues
and technical know-how.
URL:http://www.okumamerit.com
ADMAC-Parts integrates design and
production to minimize the cycle from
CAD design to cutting. Using the
MACTURN can improve efficiency in
upstream processes as well as machining
processes .
Machining expertise database
CAD/CAM software created by Okuma
Pool of information
MACTURN250/350
• Comparison of cycle times
One-saddle type multifunction machine
MACTURN250
33%Less
8 min 36 sec
5 min 46 sec
• No. of tools used: 8
Workpieceshape
and tooling
Increase in productivity 1.5 times more
Simultaneous machining with upper and lower turrets
Upper turret
Lower turret
500 (19.69)
ø80 (ø3.15)
Simultaneous machining
6
Highly efficient machining
L 7 min 41 sec
M55 sec
L 4 min 51 sec
M55 sec
14
Note: Drawings above show HSK-A63 Note: Drawings above show BT40 Big Plus
Working range (W-axis specs)
• OD toolholder A
• ID toolholder
• End mill holder
• End mill holder (side view)
φ55
0 (M
ax. t
urni
ng d
ia.)
φ16
9
1180 Travel
1170 Travel
1440260
147 520.4 356
95 261
416.6
382.2
180249.6
1303
94.696.699.4
150 99.6
52
103 39(13)�
(45
5)�
(18
0)�
1075.4 (Working range)
Rotation center
76
137
29
R 279.6
Gauge line
475
Trav
el(
255)�
455
20
228
91
298
177
156
175.
4
φ21
0
1170 Travel1303 382.2
180
Rotation centerR270
155
9065
781092 (Working range)90
2045
5
475
Trav
el(
255)�
185
φ16
9
(45
5)�
φ55
0 (M
ax. t
urni
ng d
ia.)(
180)�
φ21
0177
298
29 76137
356407
530
260 1180 Travel1440
206103 (13)�39 122 234
2324
772
133
146.
916
5.1
163
φ21
0
290
143
358.
2
475
133
368.
215
6
80
80 80
153
φ16
9
2045
547
5 Tr
avel
9495
133
179.
2
202.
2
80 802976
3446
211.
2
Section AA
44
70
39103
92
1440
550
1112
8080
80 60°�
80 80
3050
122 234(Range of Section CC)(Range of Section BB)
(Range of Section AA)
Section CC
Section BB Section DD
Section EE Section FF
(Range of Section DD) (Range of Section EE) (Range of Section FF)
MACTURN250• OD toolholder A
• ID toolholder
• End mill holder
• End mill holder (side view)
MACTURN350
79 46
66.4
φ21
0
φ55
0 (M
ax. t
urni
ng d
ia.)
(51
.6)�
178.
432
6.6
115
43 328
0.6
103
16868 1371 131
29
7 3457 33
76
(202)�260 1680 Travel
1940
39 (13)
(5)
43
133 1670 Travel1803
φ16
918
0
485
171.
438
2.2
562.
2
137
Rotation center
Gauge lineR 313.463
58 60
(96.6)�
505
Trav
el
144.
450
34 2626
6.6
φ55
0 (M
ax. t
urni
ng d
ia.)
φ16
9
1680 Travel
1670 Travel
1940260
147 1016.8 356
119652867
4532
420.21585
382.2
180263.2
1803
85
133
90412457160 103.2
31.6
65.2
103 39(13)�
(5)�
(48
5)�(
210)�
1585 (Working range)
Rotation center
76
137
29
R 2
83.2
Gauge line
505
Trav
el(
255)�
485
20
15314
1475
3330
133
177
157
940
9315
6 186
201.
8
φ21
0
107 39
.9151.
743
.316
3
φ21
0
φ29
0
143
388.
2
505
133
398.
218
6
80
80 80
153
φ16
9
2048
550
5 Tr
avel
7560
23 1219
163
209.
2
232.
2
29763446
241.
2
Section AA
55.6 51 41 70
391031940
1038.41612
8080
80 60°�
80 80
3050
67 95 25478 114(Range of Section CC)(Range of Section BB)(Range of Section AA)
Section CC
Section BB Section DD
Section EE Section FF
(Range of Section DD) (Range of Section EE) (Range of Section FF)
80 80
1670 Travel1803 382.2
180
Rotation center
R26
1.6
146.6
81.665
58133
1612 (Working range)70417333.6
2048
5
505
Trav
el(
255)�
223.
4
φ16
9
(48
5)�
φ55
0 (M
ax. t
urni
ng d
ia.)(
210)�
φ21
0177
157
103
91.7
4093 2976
137
356251149547678
398.61038.4
1612260 1680 Travel
1940
217.6103 (13)�
(5)�
39
153
133
163
7560
2319
12
79 46
40
ø21
0
ø550
(Max
. tur
ning
dia
.)(
48)�
152
323
118
4327
4
103
168 871 131
29 76
(202)�260 1180 Travel
1440
68
39
43
1170 Travel1303
φ16
935
88
(45
5)�18
014
5.1
382.
2
137
Rotation center
R 309.965 3758
(12
3)�
475
Trav
el11
3.526
010
1.5
12
Optional accessories and specifications
Note: Please consult your Okuma representative� for delivery details.
MACTURN
250MACTURN
250-WMACTURN
350MACTURN
350-W
Turning Milling
Tooling system MACTURN250 (HSK-A63, KM63, CAPTO C6)
13
Turning Milling
Tooling system MACTURN350 (BT40 Big Plus)
Milling chuck
BT40 Big PlusKM63CAPT0 C6HSK-A63
Between centers
Swing over saddle
Max machining dia.
Max machining dia.
Max work length
X axis
Z axis
Y axis
C axis
B-axis indexing angle
Spindle speed
Speed ranges
Spindle nose
Tapered bore
Bearing dia�Spindle speed
Speed ranges
Spindle nose
Tapered bore
Bearing dia
Type
No. of tools
Tool shank/boring bar shank dia
Speed range
Coolant
Rapid traverse
Tool shank type
No. of tools
Max tool dia
Max tool length
Max tool weight
Max tool moment
Tool selection
Quill dia
Quill tapered bore
Quill travel
Programmable tailstock
Main spindle�2nd-operation spindle
M-spindle
Coolant
Height
Floor space
Weight (without ATC magazine)
Okuma
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
Degree
Degree
min-1 {rpm}
mm (in.)
mm (in.)
�
�
mm�
mm�
min-1�
�
�
mm (in.)
min-1
m/min (ipm)
mm (in.)
mm (in.)
kg (lb)
kg x mm (lb x in.)
mm (in.)
mm (in.)
kW (hp)
�
kW (hp)
kW (hp)
mm (in.)
mm (in.)
kg (lb)�
�
2nd-operation spindle
�
Machine specifications
MACTURN 250-W
T
ーーーー�
MACTURN 250
ーーーーー
X: 30 Z: 40 Y: 26 C: 400 min-1
(X: 1181 Z: 1575 Y: 1024)
MACTURN 350
ーーーーー
X: 30 Z: 40 Y: 26 C: 400 min-1
(X: 1181 Z: 1575 Y: 1024)
C×1000
1,000 (39.37)
ø550 (ø21.65)
ø530 (ø20.87)
ø550 (ø21.65)
1,025 (40.35)
XA: 475 (18.70), XB: 160 (6.30)
ZA: 1,170 (40.06), ZB: 1,155 (45.47)
160 (+80~-80) {6.30 (+3.15~-3.15)}
360-degree (rotary axis control angle 0.001-degree)
1°5,000
auto 2-speed (coil switching)
JIS A 2-6
ø62 (ø2.44)
ø100 (ø3.94)
�����
ATC
1 for both L-and M-tools
□25 / ø40 (□0.98 / ø1.57)
6,000
M-spindle thru-coolant� �
HSK-A63、KM63、CAPTO C6 (selections)
30
ø90 / ø120 (ø3.54 / ø4.72)
Face tools and side tools 250(9.84)
5 (11)
5 x 100 (excluding shank) (11 x 3.94)
Random address
����
VAC 22/15 (30/20) (20 min/cont)
VAC 7.5/5. 5(10/7.5) (20 min/cont)
VAC 7.5/5. 5/3. 7 (10/7.5/5) (5 min/20 min/cont)
0.25 x 3, 0.8
2,900 (114)
3,820 x 2,645 (150 x 100)
����������������������������������
ø90 (3.54)
MT No. 5 (live center)
150 (5.91)
Auto tow-along type
������
12,500 (27,600)
����������������������������������
ø90 (3.54)
MT No. 5 (live center)
150 (5.91)
Auto tow-along type�������
13,700 (30,140)
×1000
6000
Auto 2-speed*1
φ140 flat (5.51)
φ43 (1.69)
φ80 (3.15)
MACTURN 350-W
T
���������������������������������ー�ー�ー�ー��
C×1500
1,000/1,500 (39.37/59.06)
ø550 (ø21.65)
ø530 (ø20.87)
ø550 (ø21.65)
1,625 (63.98)
XA: 505 (19.88), XB: 210 (8.27)
ZA: 1,670 (65.75), ZB: 1,655 (65.16)
190 (+95~-95) {7.48 (+3.74~-3.74)}
360-degree (rotary axis control angle 0.001-degree)
1°5,000
auto 2-speed (coil switching)
JIS A 2-6
φ62 (ø2.44)
φ100 (ø3.94)������
ATC
1 for both L-and M-tools
□25 / ø40 (□0.98 / ø1.57)
6,000
M-spindle thru-coolant�� �
BT40 BIG PLUS
30
φ90 / φ120 (ø3.54 / ø4.72)
Face tools and side tools 300 (11.81)
7 (15)
7 x 100 (excluding shank) (15 x 3.94)
Random address�����
VAC 22/15 (30/20) (20 min/cont)�VAC 11/7.5 (20 min/cont)
VAC 7.5/5. 5/3. 7 (10/7.5/5) (5 min/20 min/cont)
0.25 x 3, 0.8
2,950 (116)
4,560 x 2,910 (180 x 115)
×1500
6000
Auto 2-speed*1
φ140 flat (5.51)
φ43(1.69)
φ80(3.15)
X:30 Z:40 Y:26(X: 1181 Z: 1575 Y: 1024) C1:400min-1 C2:400min-1
X:30 Z:40 Y:26(X: 1181 Z: 1575 Y: 1024) C1:400min-1 C2:400min-1
�
-�
-�
-�
○�
�
�
�
○�
�
○�
○�
Standard
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
○�
○�
�
�
-�
-�
-�
○�
�
�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
�
○�
○�
Big-bore specs: ø120 (ø4.72 ) bearing, A2-8, 3,800min-1
Spindle bearing ø80mm (ø3.15 in.) 6,000min-1 7.5/5.5kW (10/7.5 hp)
Spindle bearing ø80mm (ø3.15 in.) 6,000min-1 11/7.5kW (10/7.5 hp)
Spindle bearing ø100mm (ø3.94 in.) 5,000min-1 11/7.5kW (10/7.5 hp)
V12 VDI (for L-tool only)
V12 VDI (for both L- and M-tools)
M-spindle speed 12,000min-1
B-axis indexing angle 0.001°Tool shank type (HSK-A63, KM63, CAPTO C6)
No. of tools (44, 80, 120)
Tailstock thrust pressure high/low selection
Tailstock live center type MTNo.4
Programmable tailstock (NC controlled)
Steadyrest
ABSOSCALE XA, ZA, Ys, XB
Spindle coolant (A, B)
Shower coolant system (A, B)
High-pressure coolant 1.5MPa、3.0MPa、7MPa
Spindle
2nd-operationspindle
Lower turret
M-spindle
B-axis
ATC
Tailstock
Steadyrest
ABSOSCALE
Coolant
MACTURN
250MACTURN
250-WMACTURN
350MACTURN
350-W
○�
○�
○�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
Touch sensor (M, A)
In-process gauging system
Side and rear
Rear only�
Chip bucket (L, H)�
Lubrication monitor (B-1, B-2, C-1, C-2)
Oil skimmer�
Heat deviation compensation*
Auto open/close front cover
Air blow chuck, tailstock�
Bar feeder
Parts catcher
Loader
Robot
Transformer
CE compliant
Gauging
�Chip conveyor�
�
�Other
OSP-E100L
Capacity
Travels
Spindle
Turret
M-spindle
Feedrate
ATC
Tailstock
Motors
Machine size
CNC
7
Machine structure for high accuracy and productivity
Heavy cutting at high speed with our highly rigid spindle, based on accumulated expertise in design and advanced manufacturing.
Large capacity VAC motors
Powerful turning example
MACTURN250/350(Workpiece material: S45C)
Heavy-dutycutting
•OD cutting 2.5 mm2 (0.0039 in.2)Cutting speed 100 m/min (328 fpm)Cutting depth 5 mm (0.20 in.)Feedrate 0.5 mm/rev (0.02 ipr)
•Drill ø32 (ø1.26 in.) (HSS)Cutting speed 30 m/min (98 fpm)Feedrate 0.4 mm/rev (0.016 ipr)
M-spindle thru-coolant TailstockImproves chip disposal, tool life, and machining accuracy of deep hole machining. (1.5 MPa, 3.0 MPa, 7.0 MPa)
An auto towalong type, the tailstock clamps automatically and accurately positions for rigid shaft-work operations.
• Spindle motorMACTURN250/350 VAC 22/15 kW (30/20 hp)(20 min/cont)
30 3850 100 200 300 500 1000 2000 5000 30 3850 100 200 300 500 1000 2000 5000
5,000 min-1 specs[φ100 (φ3.921) std spindle]
3,800 min-1 specs[φ120 (φ4.72) big-bore spindle]
30 50 100 1000500300200 6000200038
161.6 N・m
110.2 N・m 11 kW(20分)
7.5 kW(連続)100.0 N・m
68.2 N・m
MACTURN250VAC 11/7.5 kW(20 min/cont)6,000 min-1 spec
420.2 N•m(310ft-lbf)
286.5 N•m(211ft-lbf)
168.1 N•m(124ft-lbf)
114.6 N•m(84ft-lbf)
22 kW(30hp)(20 min)
15 kW(20hp)(cont.)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1
420.2 N•m(310ft-lbf)
286.5 N•m(211ft-lbf)
168.1 N•m(124ft-lbf)
114.6 N•m(84ft-lbf)
22 kW(30hp)(20 min)
15 kW(20hp)(cont.)
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
Spindle speed, min-1
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
Spindle speed, min-1
φ0.25~φ20
Collet
Straight colletφ6φ8φ10φ12
φ16φ20φ25
Collet holder
End face arbor
*1. Coil switching
*Boring bar
Boring bar sleeve
ø10
ø12
ø16
ø20
ø25
ø32
ø8-H40
ø10-H40
ø12-H40
ø16-H40
ø20-H40
ø25-H40
ø32-H40
MT No.1-H40
MT No.2-H40
MT No.3-H40
MT No.4-H40
ø40
*Boring bar
shank dia.
Drill sleeve
MT No.1
MT No.2
MT No.3
MT No.4
*Drill
*Commercial parts
H1 turret
OD toolholder Afor OD machining
*OD tool shank(for both main and sub)
25X25
OD toolholder Efor both end facingand OD machining
OD toolholder 80-degreediamond-shapedfor OD machining
OD toolholder 55-degreediamond-shapedfor OD machining
ID toolholder H40for ID machining
Straight colletø6ø8
ø10ø12
ø2.4~ø10
ø5.8~ø20
Collet
Collet
Milling chuck
Collet holder
Collet holder
End face arbor
Some commercial live tools, based onDIN69893-1 HSK-A63, can also be used.
Some commercial live tools, based onMAS403 JIS B6339, can also be used.
ø16ø20ø25
*Boring bar
Boring bar sleeve
ø10ø12ø16ø20ø25ø32
ø10-H40
ø12-H40
ø16-H40
ø20-H40
ø25-H40
ø32-H40
MT No.1-H40
MT No.2-H40
MT No.3-H40
MT No.4-H40
ø40
*Boring bar
shank dia.
Drill sleeve
MT No.1MT No.2MT No.3MT No.4
*Drill
*Commercial parts
H1 turret
OD toolholder A-H1for OD machining
*OD tool shank(for both main and sub)
25X25
OD toolholder E-H1for both end facingand OD machining
OD toolholder 80-degreediamond-shapedfor OD machining
OD toolholder 55-degreediamond-shapedfor OD machining
ID toolholder H1for ID machining
Above drawing for HSK-A63
5
Highly accurate machining
Roundness 0.3 µm (11.81 µin.)
Workpiece material BSBSpindle speed 3,000 min-1
Surface roughness 0.4 µm (15.75 µin.)(blade edge uniformity)Workpiece material BSBSpindle speed 2,500 min-1
Roundness: 0.3 µm (11.81 µin.)Center method: LSCFilter: 50 U/R(2CR)
Magnification: x 5000Data No. 13
(actual value) (actual value)
Cross section curve(Longitudinal magnification: x 5,000.00 Lateral magnification: x 50.00)
Cross section curve(Longitudinal magnification: x 5,000.00 Lateral magnification: x 50.00)
8
Powerful milling example
MACTURN250/350(Workpiece material: S45C)
Face milling ø80 face milling (4-blade)(ø3.15) Cutting width 59.5 mm (2.34 in.)
Cutting depth 1.6 mm (0.06 in.)Feedrate 0.3 mm/rev. (0.01 ipr)Metal removal 68 cm3/min (4.15 in.3/min)
End milling ø20 (4-flute)Cutting depth 10 mm (0.39 in.)Feedrate 0.1 mm/rev. (0.004 ipr)
Tapping M16 P2
High-capacity live-tool machiningThe M-spindle motor provides full-power from the low to the high speed range for robust live-tool machining.
Powerful 2nd-operation spindleThe 2nd-operation spindle also has the extra power needed for complete primary/secondary operations.
2nd-operation spindle example
MACTURN250/350(Workpiece material: S45C)
Heavy-dutycutting
• M-tool motor�MACTURN250/350VAC 7.5/5.5/3.7 kW (10/7.5/5 hp)(5 min/20 min/cont)
10�(14)
20010050 300 500 10001100 6000
2000 5000 10000 20000
5�(7)
3�(4)2�
(3)
1�(1)
0.5�(0.7)
0.3�(0.4)
100�(74)65.1N・m(48ft-lbf)
5.5kW5.5kW(2020分)(20min20min)�
3.7kW3.7kW(連続連続)(cont.cont.)�
47.7N・m(35ft-lbf)
32.1N・m�(24ft-lbf)
50�(37)
30
20
10�(7)
5�(4)
3(2)
6,000 min-1
20050 10001200
3000 5000 1000012000
12,000 min-1 (Optional)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
5(7)
10(14)
Spindle speed, min-1Spindle speed, min-1
3(4)
2(3)
1(1)
0.5(0.7)
0.2(0.4)
100(74)7.5kW(10hp)(5min)
5.5kW(7.5hp)(20min)
3.7kW(5hp)(cont.)50(37)
10(7)
5(4)
59.7N•m(43.99ft-lbf)(5min)
23.9N•m(17.61ft-lbf)(5min)
43.8N•m(32.28ft-lbf)(20min)
17.5N•m(12.90ft-lbf)(20min)
29.5N•m(21.75ft-lbf)(Cont.)
11.8N•m(8.70ft-lbf)(Cont.)
7.5kW(10hp)(5min)
5.5kW(7.5hp)(20min)
3.7kW(5hp)(cont.)
30 3850 100 200 300 500 1000 2000 60001
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
MACTURN250-WVAC 7.5/5.5 kW (10/7.5 hp)(20 min/cont)6,000min-1 spec
MACTURN250-W/350-WVAC 11/7.5 kW (15/10 hp)(20 min/cont)6,000min-1 spec
MACTURN350-WVAC 15/11/7.5 kW(5 min/20 min/cont)5,000 min-1 specφ100 (φ3.94) big-bore spindle
MACTURN350-WVAC 11/7.5 kW (20 min/cont)5,000 min-1 specφ100 (φ3.94) big-bore spindle
30 50 100 1000500300200 6000200038
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
161.6 N・m(119ft-lbf)
110.2 N・m(81ft-lbf) 11 kW(15hp)(20 min)
7.5 kW(10hp)(cont.)100.0 N・m(74ft-lbf)
68.2 N・m(50ft-lbf)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
1000(737)
30 50 100 1000500
600 1400
300200 6000200045
1(1)
0.5
0.3
0.2
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
119.3 N・m(12.18ft-lbf)175.0 N・m(17.86ft-lbf)
102.3 N・m(10.44ft-lbf) 11 kW(20 min)
7.5 kW(cont.)
15 kW(5 min)
75.0 N・m(7.65ft-lbf)51.1 N・m(5.22ft-lbf)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
30 50 100 1000500
650 1050
300200 6000200045
1(1)
0.5
0.3
0.2
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
110.1 N・m(11.24ft-lbf)
161.5 N・m(16.48ft-lbf)11 kW(20 min)
7.5 kW(cont.)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1 Spindle speed, min-1 Spindle speed, min-1
159.2 N•m(117ft-lbf)116.7 N•m(86ft-lbf)
68.2N•m(50ft-lbf)50.0 N•m(37ft-lbf)
7.5 kW(10hp)(20 min)
5.5 kW(7.5hp)(cont.)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
200(147)
300(221)
500(369)
1000(737)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
•OD cutting 1.5 mm2 (0.002 in.2)Cutting speed 100 m/min (328 fpm)Cutting depth 5 mm (0.20 in.)Feedrate 0.3 mm/rev (0.01 ipr)
�
9 10
Optional equipment
44/80/120-tool ATCLarger tool capacity for wider range of machining
Touch sensorAuto cutting-point measurement and tool offset/breakage detection
Hybrid coolantOkuma's hybrid coolant system lets you cut with oil and cool down with water, so you save coolant and extend the life of your tools.
ABSO SCALE
This high-speed high-resolution [0.1 mm (4 min.)] optical absolute position encoder developed by Okuma improves machining accuracy by avoiding ball-screw thermal expansion and backlash.
* A stand may be necessary depending on the type of conveyor. * Chip conveyors developed for machining hard materials are also available.
• Chip conveyor types and applications
Various chip conveyors
Versatile machining variations
• Hob speed 1,000 min-1
• Feedrate: 2 mm/rev (0.079 ipr)
Infrared in-process gaugingBy ATC-delivered, high-precision wireless touch sensor- for superb auto work gauging (dual dia/radius gauging).
High-pressure coolantunit (7 Mpa specification)
High-pressure coolant flushes chips, eficiently cools tool tips, and extends tool life.
Bar feedersWith part catchers, long and automated operations also possible with the various bar feeder systems available.
OGL gantry loadersAble to handle a flexible arrangement of workpieces, Okuma gantry loaders help automate production lines, and with massive stackers provide long runs.
Type
Application
Shape
Hinge Scraper Magnetic scraperHinge
Scraper + Drum Filter
• Used generally for NC lathes
• For cast iron• Easy for maintenance • Blade scraper (Magnetic scraper more
effective for sludge)
Magnet
• For cast iron• Suitable for sludge
• For cast iron and steel • Coolant filtered from
aluminum or cast ironchips (long or short)
Helical cuttingDone with small-diameter rotating tools in big holes. Helical cutting on slopes also possible.
M30P1.5Pitch 1.5 (0.06)
ø16(ø0.63)
You can turn reverse tapers as shown below by drawing the B-axis gradually back along the slope at the desired angle.
B-axis reverse taper turning
Blade machiningHighly accurate machining and synchronized control, even for highly accurate shaping of complicated blades
HobbingGear cutting with hob cutter
Eccentric cutting (cam)Eccentric cutting for cams and similar shapes can be programmed and machined very efficiently.
X
Y
C
GrindingGrinding with the M-spindle's cup grinding wheel
9 10
Optional equipment
44/80/120-tool ATCLarger tool capacity for wider range of machining
Touch sensorAuto cutting-point measurement and tool offset/breakage detection
Hybrid coolantOkuma's hybrid coolant system lets you cut with oil and cool down with water, so you save coolant and extend the life of your tools.
ABSO SCALE
This high-speed high-resolution [0.1 mm (4 min.)] optical absolute position encoder developed by Okuma improves machining accuracy by avoiding ball-screw thermal expansion and backlash.
* A stand may be necessary depending on the type of conveyor. * Chip conveyors developed for machining hard materials are also available.
• Chip conveyor types and applications
Various chip conveyors
Versatile machining variations
• Hob speed 1,000 min-1
• Feedrate: 2 mm/rev (0.079 ipr)
Infrared in-process gaugingBy ATC-delivered, high-precision wireless touch sensor- for superb auto work gauging (dual dia/radius gauging).
High-pressure coolantunit (7 Mpa specification)
High-pressure coolant flushes chips, eficiently cools tool tips, and extends tool life.
Bar feedersWith part catchers, long and automated operations also possible with the various bar feeder systems available.
OGL gantry loadersAble to handle a flexible arrangement of workpieces, Okuma gantry loaders help automate production lines, and with massive stackers provide long runs.
Type
Application
Shape
Hinge Scraper Magnetic scraperHinge
Scraper + Drum Filter
• Used generally for NC lathes
• For cast iron• Easy for maintenance • Blade scraper (Magnetic scraper more
effective for sludge)
Magnet
• For cast iron• Suitable for sludge
• For cast iron and steel • Coolant filtered from
aluminum or cast ironchips (long or short)
Helical cuttingDone with small-diameter rotating tools in big holes. Helical cutting on slopes also possible.
M30P1.5Pitch 1.5 (0.06)
ø16(ø0.63)
You can turn reverse tapers as shown below by drawing the B-axis gradually back along the slope at the desired angle.
B-axis reverse taper turning
Blade machiningHighly accurate machining and synchronized control, even for highly accurate shaping of complicated blades
HobbingGear cutting with hob cutter
Eccentric cutting (cam)Eccentric cutting for cams and similar shapes can be programmed and machined very efficiently.
X
Y
C
GrindingGrinding with the M-spindle's cup grinding wheel
16
Production information network presented by OkumaOSP-E100, ADMAC-Parts, KCMAC, and MacMan can help you.IT Plaza
Solving all your problems with our reliable machining technology accessed via IT technology.
Instantly picks up the production plan and actual work site
performance data.
Ideal for controlling production of a variety of workpieces, small
volumes, and products with short leadtime.
Easily pick up any standstill in production
MacManProduction control software
Central to IT Plaza
OSP-E100Intuitive CNC
The OSP Browser gives instant access to information
Real 3-D simulation lets you experience the cutting process without making a single chip
OSP-WinX manipulates machines
One touch IGF-XM enhances machining
11
Machining examples
• Material: SCM415• Product: Tool
• Material: S45C• Product: Bearing
• Material: SKD• Product: Die
• Material: Aluminum• Product: Engine parts
• Material: Aluminum• Product: Construction parts
• Material: FC• Product: Pump parts
• Material: Stainless steel or equivalent• Product: Aircraft parts
• Material: Aluminum• Product: Automobile parts
• Material: Stainless steel• Product: Atomic parts
Machining range
Note: [ ] for MACTURN350. Please see "Working range" on page 14 for details.
475 [505](18.70
[19.88])
1,170 [1,670](46,06 [65.75])
160 [190](6.30 [7.48])
12
Optional accessories and specifications
Note: Please consult your Okuma representative� for delivery details.
MACTURN
250MACTURN
250-WMACTURN
350MACTURN
350-W
Turning Milling
Tooling system MACTURN250 (HSK-A63, KM63, CAPTO C6)
13
Turning Milling
Tooling system MACTURN350 (BT40 Big Plus)
Milling chuck
BT40 Big PlusKM63CAPT0 C6HSK-A63
Between centers
Swing over saddle
Max machining dia.
Max machining dia.
Max work length
X axis
Z axis
Y axis
C axis
B-axis indexing angle
Spindle speed
Speed ranges
Spindle nose
Tapered bore
Bearing dia�Spindle speed
Speed ranges
Spindle nose
Tapered bore
Bearing dia
Type
No. of tools
Tool shank/boring bar shank dia
Speed range
Coolant
Rapid traverse
Tool shank type
No. of tools
Max tool dia
Max tool length
Max tool weight
Max tool moment
Tool selection
Quill dia
Quill tapered bore
Quill travel
Programmable tailstock
Main spindle�2nd-operation spindle
M-spindle
Coolant
Height
Floor space
Weight (without ATC magazine)
Okuma
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
mm (in.)
Degree
Degree
min-1 {rpm}
mm (in.)
mm (in.)
�
�
mm�
mm�
min-1�
�
�
mm (in.)
min-1
m/min (ipm)
mm (in.)
mm (in.)
kg (lb)
kg x mm (lb x in.)
mm (in.)
mm (in.)
kW (hp)
�
kW (hp)
kW (hp)
mm (in.)
mm (in.)
kg (lb)�
�
2nd-operation spindle
�
Machine specifications
MACTURN 250-W
T
ーーーー�
MACTURN 250
ーーーーー
X: 30 Z: 40 Y: 26 C: 400 min-1
(X: 1181 Z: 1575 Y: 1024)
MACTURN 350
ーーーーー
X: 30 Z: 40 Y: 26 C: 400 min-1
(X: 1181 Z: 1575 Y: 1024)
C×1000
1,000 (39.37)
ø550 (ø21.65)
ø530 (ø20.87)
ø550 (ø21.65)
1,025 (40.35)
XA: 475 (18.70), XB: 160 (6.30)
ZA: 1,170 (40.06), ZB: 1,155 (45.47)
160 (+80~-80) {6.30 (+3.15~-3.15)}
360-degree (rotary axis control angle 0.001-degree)
1°5,000
auto 2-speed (coil switching)
JIS A 2-6
ø62 (ø2.44)
ø100 (ø3.94)
�����
ATC
1 for both L-and M-tools
□25 / ø40 (□0.98 / ø1.57)
6,000
M-spindle thru-coolant� �
HSK-A63、KM63、CAPTO C6 (selections)
30
ø90 / ø120 (ø3.54 / ø4.72)
Face tools and side tools 250(9.84)
5 (11)
5 x 100 (excluding shank) (11 x 3.94)
Random address
����
VAC 22/15 (30/20) (20 min/cont)
VAC 7.5/5. 5(10/7.5) (20 min/cont)
VAC 7.5/5. 5/3. 7 (10/7.5/5) (5 min/20 min/cont)
0.25 x 3, 0.8
2,900 (114)
3,820 x 2,645 (150 x 100)
����������������������������������
ø90 (3.54)
MT No. 5 (live center)
150 (5.91)
Auto tow-along type
������
12,500 (27,600)
����������������������������������
ø90 (3.54)
MT No. 5 (live center)
150 (5.91)
Auto tow-along type�������
13,700 (30,140)
×1000
6000
Auto 2-speed*1
φ140 flat (5.51)
φ43 (1.69)
φ80 (3.15)
MACTURN 350-W
T
���������������������������������ー�ー�ー�ー��
C×1500
1,000/1,500 (39.37/59.06)
ø550 (ø21.65)
ø530 (ø20.87)
ø550 (ø21.65)
1,625 (63.98)
XA: 505 (19.88), XB: 210 (8.27)
ZA: 1,670 (65.75), ZB: 1,655 (65.16)
190 (+95~-95) {7.48 (+3.74~-3.74)}
360-degree (rotary axis control angle 0.001-degree)
1°5,000
auto 2-speed (coil switching)
JIS A 2-6
φ62 (ø2.44)
φ100 (ø3.94)������
ATC
1 for both L-and M-tools
□25 / ø40 (□0.98 / ø1.57)
6,000
M-spindle thru-coolant�� �
BT40 BIG PLUS
30
φ90 / φ120 (ø3.54 / ø4.72)
Face tools and side tools 300 (11.81)
7 (15)
7 x 100 (excluding shank) (15 x 3.94)
Random address�����
VAC 22/15 (30/20) (20 min/cont)�VAC 11/7.5 (20 min/cont)
VAC 7.5/5. 5/3. 7 (10/7.5/5) (5 min/20 min/cont)
0.25 x 3, 0.8
2,950 (116)
4,560 x 2,910 (180 x 115)
×1500
6000
Auto 2-speed*1
φ140 flat (5.51)
φ43(1.69)
φ80(3.15)
X:30 Z:40 Y:26(X: 1181 Z: 1575 Y: 1024) C1:400min-1 C2:400min-1
X:30 Z:40 Y:26(X: 1181 Z: 1575 Y: 1024) C1:400min-1 C2:400min-1
�
-�
-�
-�
○�
�
�
�
○�
�
○�
○�
Standard
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
○�
○�
�
�
-�
-�
-�
○�
�
�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
�
○�
○�
Big-bore specs: ø120 (ø4.72 ) bearing, A2-8, 3,800min-1
Spindle bearing ø80mm (ø3.15 in.) 6,000min-1 7.5/5.5kW (10/7.5 hp)
Spindle bearing ø80mm (ø3.15 in.) 6,000min-1 11/7.5kW (10/7.5 hp)
Spindle bearing ø100mm (ø3.94 in.) 5,000min-1 11/7.5kW (10/7.5 hp)
V12 VDI (for L-tool only)
V12 VDI (for both L- and M-tools)
M-spindle speed 12,000min-1
B-axis indexing angle 0.001°Tool shank type (HSK-A63, KM63, CAPTO C6)
No. of tools (44, 80, 120)
Tailstock thrust pressure high/low selection
Tailstock live center type MTNo.4
Programmable tailstock (NC controlled)
Steadyrest
ABSOSCALE XA, ZA, Ys, XB
Spindle coolant (A, B)
Shower coolant system (A, B)
High-pressure coolant 1.5MPa、3.0MPa、7MPa
Spindle
2nd-operationspindle
Lower turret
M-spindle
B-axis
ATC
Tailstock
Steadyrest
ABSOSCALE
Coolant
MACTURN
250MACTURN
250-WMACTURN
350MACTURN
350-W
○�
○�
○�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
○�
Touch sensor (M, A)
In-process gauging system
Side and rear
Rear only�
Chip bucket (L, H)�
Lubrication monitor (B-1, B-2, C-1, C-2)
Oil skimmer�
Heat deviation compensation*
Auto open/close front cover
Air blow chuck, tailstock�
Bar feeder
Parts catcher
Loader
Robot
Transformer
CE compliant
Gauging
�Chip conveyor�
�
�Other
OSP-E100L
Capacity
Travels
Spindle
Turret
M-spindle
Feedrate
ATC
Tailstock
Motors
Machine size
CNC
7
Machine structure for high accuracy and productivity
Heavy cutting at high speed with our highly rigid spindle, based on accumulated expertise in design and advanced manufacturing.
Large capacity VAC motors
Powerful turning example
MACTURN250/350(Workpiece material: S45C)
Heavy-dutycutting
•OD cutting 2.5 mm2 (0.0039 in.2)Cutting speed 100 m/min (328 fpm)Cutting depth 5 mm (0.20 in.)Feedrate 0.5 mm/rev (0.02 ipr)
•Drill ø32 (ø1.26 in.) (HSS)Cutting speed 30 m/min (98 fpm)Feedrate 0.4 mm/rev (0.016 ipr)
M-spindle thru-coolant TailstockImproves chip disposal, tool life, and machining accuracy of deep hole machining. (1.5 MPa, 3.0 MPa, 7.0 MPa)
An auto towalong type, the tailstock clamps automatically and accurately positions for rigid shaft-work operations.
• Spindle motorMACTURN250/350 VAC 22/15 kW (30/20 hp)(20 min/cont)
30 3850 100 200 300 500 1000 2000 5000 30 3850 100 200 300 500 1000 2000 5000
5,000 min-1 specs[φ100 (φ3.921) std spindle]
3,800 min-1 specs[φ120 (φ4.72) big-bore spindle]
30 50 100 1000500300200 6000200038
161.6 N・m
110.2 N・m 11 kW(20分)
7.5 kW(連続)100.0 N・m
68.2 N・m
MACTURN250VAC 11/7.5 kW(20 min/cont)6,000 min-1 spec
420.2 N•m(310ft-lbf)
286.5 N•m(211ft-lbf)
168.1 N•m(124ft-lbf)
114.6 N•m(84ft-lbf)
22 kW(30hp)(20 min)
15 kW(20hp)(cont.)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
Spindle speed, min-1
420.2 N•m(310ft-lbf)
286.5 N•m(211ft-lbf)
168.1 N•m(124ft-lbf)
114.6 N•m(84ft-lbf)
22 kW(30hp)(20 min)
15 kW(20hp)(cont.)
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
Spi
ndle
torq
ue, N
•m (
ft-lb
f)
1
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
Spindle speed, min-1
1(1)
2(3)
3(4)
5(7)
10(14)
20(27)
30(40)
50(68)
100(136)
Spi
ndle
mot
or o
utpu
t, kW
(hp
)
2(1)
3(2)
5(4)
10(7)
20(15)
30(22)
50(37)
100(74)
300(221)
500(369)
1000(737)
Spindle speed, min-1
φ0.25~φ20
Collet
Straight colletφ6φ8φ10φ12
φ16φ20φ25
Collet holder
End face arbor
*1. Coil switching
*Boring bar
Boring bar sleeve
ø10
ø12
ø16
ø20
ø25
ø32
ø8-H40
ø10-H40
ø12-H40
ø16-H40
ø20-H40
ø25-H40
ø32-H40
MT No.1-H40
MT No.2-H40
MT No.3-H40
MT No.4-H40
ø40
*Boring bar
shank dia.
Drill sleeve
MT No.1
MT No.2
MT No.3
MT No.4
*Drill
*Commercial parts
H1 turret
OD toolholder Afor OD machining
*OD tool shank(for both main and sub)
25X25
OD toolholder Efor both end facingand OD machining
OD toolholder 80-degreediamond-shapedfor OD machining
OD toolholder 55-degreediamond-shapedfor OD machining
ID toolholder H40for ID machining
Straight colletø6ø8
ø10ø12
ø2.4~ø10
ø5.8~ø20
Collet
Collet
Milling chuck
Collet holder
Collet holder
End face arbor
Some commercial live tools, based onDIN69893-1 HSK-A63, can also be used.
Some commercial live tools, based onMAS403 JIS B6339, can also be used.
ø16ø20ø25
*Boring bar
Boring bar sleeve
ø10ø12ø16ø20ø25ø32
ø10-H40
ø12-H40
ø16-H40
ø20-H40
ø25-H40
ø32-H40
MT No.1-H40
MT No.2-H40
MT No.3-H40
MT No.4-H40
ø40
*Boring bar
shank dia.
Drill sleeve
MT No.1MT No.2MT No.3MT No.4
*Drill
*Commercial parts
H1 turret
OD toolholder A-H1for OD machining
*OD tool shank(for both main and sub)
25X25
OD toolholder E-H1for both end facingand OD machining
OD toolholder 80-degreediamond-shapedfor OD machining
OD toolholder 55-degreediamond-shapedfor OD machining
ID toolholder H1for ID machining
Above drawing for HSK-A63
15
Access MACTURN production support tool via IT Plaza
Creating new techniques by transferring and sharing techniques and expertise to
produce quality products.
Efficiency improved from the pre-operation stage!
ADMAC-Parts Turning
Passing on successful techniques
KCMAC Bridge to customersKnowledge Creation for Machining
Okuma makes all information required to produce
quality products openly available, including clues
and technical know-how.
URL:http://www.okumamerit.com
ADMAC-Parts integrates design and
production to minimize the cycle from
CAD design to cutting. Using the
MACTURN can improve efficiency in
upstream processes as well as machining
processes .
Machining expertise database
CAD/CAM software created by Okuma
Pool of information
MACTURN250/350
• Comparison of cycle times
One-saddle type multifunction machine
MACTURN250
33%Less
8 min 36 sec
5 min 46 sec
• No. of tools used: 8
Workpieceshape
and tooling
Increase in productivity 1.5 times more
Simultaneous machining with upper and lower turrets
Upper turret
Lower turret
500 (19.69)
ø80 (ø3.15)
Simultaneous machining
6
Highly efficient machining
L 7 min 41 sec
M55 sec
L 4 min 51 sec
M55 sec
14
Note: Drawings above show HSK-A63 Note: Drawings above show BT40 Big Plus
Working range (W-axis specs)
• OD toolholder A
• ID toolholder
• End mill holder
• End mill holder (side view)
φ55
0 (M
ax. t
urni
ng d
ia.)
φ16
9
1180 Travel
1170 Travel
1440260
147 520.4 356
95 261
416.6
382.2
180249.6
1303
94.696.699.4
150 99.6
52
103 39(13)�
(45
5)�
(18
0)�
1075.4 (Working range)
Rotation center
76
137
29
R 279.6
Gauge line
475
Trav
el(
255)�
455
20
228
91
298
177
156
175.
4
φ21
0
1170 Travel1303 382.2
180
Rotation centerR270
155
9065
781092 (Working range)90
2045
5
475
Trav
el(
255)�
185
φ16
9
(45
5)�
φ55
0 (M
ax. t
urni
ng d
ia.)(
180)�
φ21
0177
298
29 76137
356407
530
260 1180 Travel1440
206103 (13)�39 122 234
2324
772
133
146.
916
5.1
163
φ21
0
290
143
358.
2
475
133
368.
215
6
80
80 80
153
φ16
9
2045
547
5 Tr
avel
9495
133
179.
2
202.
2
80 802976
3446
211.
2
Section AA
44
70
39103
92
1440
550
1112
8080
80 60°�
80 80
3050
122 234(Range of Section CC)(Range of Section BB)
(Range of Section AA)
Section CC
Section BB Section DD
Section EE Section FF
(Range of Section DD) (Range of Section EE) (Range of Section FF)
MACTURN250• OD toolholder A
• ID toolholder
• End mill holder
• End mill holder (side view)
MACTURN350
79 46
66.4
φ21
0
φ55
0 (M
ax. t
urni
ng d
ia.)
(51
.6)�
178.
432
6.6
115
43 328
0.6
103
16868 1371 131
29
7 3457 33
76
(202)�260 1680 Travel
1940
39 (13)
(5)
43
133 1670 Travel1803
φ16
918
0
485
171.
438
2.2
562.
2
137
Rotation center
Gauge lineR 313.463
58 60
(96.6)�
505
Trav
el
144.
450
34 2626
6.6
φ55
0 (M
ax. t
urni
ng d
ia.)
φ16
9
1680 Travel
1670 Travel
1940260
147 1016.8 356
119652867
4532
420.21585
382.2
180263.2
1803
85
133
90412457160 103.2
31.6
65.2
103 39(13)�
(5)�
(48
5)�(
210)�
1585 (Working range)
Rotation center
76
137
29
R 2
83.2
Gauge line
505
Trav
el(
255)�
485
20
15314
1475
3330
133
177
157
940
9315
6 186
201.
8
φ21
0
107 39
.9151.
743
.316
3
φ21
0
φ29
0
143
388.
2
505
133
398.
218
6
80
80 80
153
φ16
9
2048
550
5 Tr
avel
7560
23 1219
163
209.
2
232.
2
29763446
241.
2
Section AA
55.6 51 41 70
391031940
1038.41612
8080
80 60°�
80 80
3050
67 95 25478 114(Range of Section CC)(Range of Section BB)(Range of Section AA)
Section CC
Section BB Section DD
Section EE Section FF
(Range of Section DD) (Range of Section EE) (Range of Section FF)
80 80
1670 Travel1803 382.2
180
Rotation centerR
261.
6
146.6
81.665
58133
1612 (Working range)70417333.6
2048
5
505
Trav
el(
255)�
223.
4
φ16
9
(48
5)�
φ55
0 (M
ax. t
urni
ng d
ia.)(
210)�
φ21
0177
157
103
91.7
4093 2976
137
356251149547678
398.61038.4
1612260 1680 Travel
1940
217.6103 (13)�
(5)�
39
153
133
163
7560
2319
12
79 46
40
ø21
0
ø550
(Max
. tur
ning
dia
.)(
48)�
152
323
118
4327
4
103
168 871 131
29 76
(202)�260 1180 Travel
1440
68
39
43
1170 Travel1303
φ16
935
88
(45
5)�18
014
5.1
382.
2
137
Rotation center
R 309.965 3758
(12
3)�
475
Trav
el11
3.526
010
1.5
16
Production information network presented by OkumaOSP-E100, ADMAC-Parts, KCMAC, and MacMan can help you.IT Plaza
Solving all your problems with our reliable machining technology accessed via IT technology.
Instantly picks up the production plan and actual work site
performance data.
Ideal for controlling production of a variety of workpieces, small
volumes, and products with short leadtime.
Easily pick up any standstill in production
MacManProduction control software
Central to IT Plaza
OSP-E100Intuitive CNC
The OSP Browser gives instant access to information
Real 3-D simulation lets you experience the cutting process without making a single chip
OSP-WinX manipulates machines
One touch IGF-XM enhances machining
15
Access MACTURN production support tool via IT Plaza
Creating new techniques by transferring and sharing techniques and expertise to
produce quality products.
Efficiency improved from the pre-operation stage!
ADMAC-Parts Turning
Passing on successful techniques
KCMAC Bridge to customersKnowledge Creation for Machining
Okuma makes all information required to produce
quality products openly available, including clues
and technical know-how.
URL:http://www.okumamerit.com
ADMAC-Parts integrates design and
production to minimize the cycle from
CAD design to cutting. Using the
MACTURN can improve efficiency in
upstream processes as well as machining
processes .
Machining expertise database
CAD/CAM software created by Okuma
Pool of information
17 18
OSP-E100L CNCStandard Specifications
BasicFunctions
Operations
OtherFunctions
X, Z simultaneous 2-axis turning, X, Z, C simultaneous 3-axis multi-axis machining
OSP full range absolute position feedback (zero point return not required)
N4, G3, X+53, Y+53, Z+53, I+53, K+53, F+53, S4, T6, M3
RS-232-C interface, 1 channel
3.5" floppy disk drive (built-in type)
Input/output a program via OSP or MS-DOS (FAT) formats
Accepts long file names, Auto ISO/EIA code recognition
Auto ISO/EIA code recognition; absolute, incremental, or both
X-axis: 1 µm (0.00004 in.) [dia], Z-axis: 1 µm (0.00004 in.), C-axis: 0.001-degree
8-digit decimal, ±99999.999 mm
1 µm (0.00004 in.), 10 µm (0.0004 in.), 1 mm (0.04 in.) (Freely selectable)
1 µm (0.00004 in.), 10 µm (0.0004 in.), 1 mm (0.04 in.) increments
Feedrates are listed in the machine specs; override: 0 to 200%, dwell: 0.01 to 99999.99 sec.
Tool selection: 12 sets, tool offset (compensation): 32 sets, max offset value: ±99999.999 mm
Auto tool offset: calculated from input wear and measured values
Direct spindle speed commands (S4), constant cutting speed, spindle speed override
(50 to 200%), optimum turning speed designation
Direct spindle speed command
10.4" color TFT, six LEDS for display of operating conditions
Spindle (jog, CW, CCW), tool rotation, pulse handle, X-/Z-axis manual feed
Program writing, editing during cutting
Automatic diagnostics and display of program, operation, machine, and NC system problems
Safety function to interlock machine movement when the door is opened or closed
Instant detection of machine collision to minimize machine damage
Calculates motor speed and torque per mathematical speed control --- for fast and stable positioning
Machining progress is calculated and displayed for each main program
Machine operating time (power supply, cutting) is calculated and displayed
Machine operating time is calculated and displayed in time charts
Machining results, operating results, operating records, and trouble information are output to a floppy disk
Featuring easy-to-manipulate screen windows
Pop-up function displays
Quick closing windows
Cursor advances to a specified sequence number in the selected program
Displays feed axis and spindle loads, with peak value hold
To restart from the beginning of an interrupted sequence
For manual operations during automatic operation; automatic return to interrupt point
Slide hold during threading (optional for G34/G35 non-fixed cycles)
Two programs can be edited simultaneously on one screen, and programs can be edited during operation
One program: 128 KB [320 m (1050 ft)], Program storage: 128 KB [320 m (1050 ft)]
Alarm help, G/M code help, system variable help, operation help, diagram display
Displays PLC ladder drawings and PLC data
Output tool offset, zero offset, and measurement data to floppy disk
Automatic compensation for tool nose radius dimension errors including arbitrary shapes and arcs
Circular interpolation by defining the radius L and end points X and Z
Simple programming of arbitrary angle chamfers (C, R)
Taper interpolation by designating either the X or Z-axis and the starting point angle
Both mm/rev and mm/min (ipr and ipm) feedrates can be used
Non-stop operation possible by setting the sequence of several part programs
Programmed zero offsets are possible
Thread lead: 0.001~1000.000 mm (0.00004~39.37 in.), number of threads can be set
Variable lead threading available, chamfering ON/OFF, fixed cycle threading,
non-fixed cycle threading
(Thread leads depend on CNC limit values; max lead differs per machine.)
Threading cycle, grooving cycle, drilling cycle
Drilling, deep-hole drilling, boring, tapping (Synchronized tapping)
GOTO, IF statements, arithmetic, common variables (200 sets), local variables,
system variables (per machine movement)
Comments can be added to programs
Control
Position feedback
Tape format
RS-232-C interface
Programming
Min input increment
Max input dimension
Programmable units
Decimal point data
Feed
Live tool VAC motor drive
Display
Manual operation
Multitasking
Self-diagnostics
Door interlock
NC torque limiter
Hi-G control
Sequence number search
Load meter
Sequence restart
Manual interrupt/auto return
Threading slide hold
Programming
Program capacity
''Pocket'' manual
PLC monitor
Data input/output
Tool nose R compensation (2B)
Arc radius direct programming
Arbitrary angle chamfering
Taper angle direct programming
Dual feed unit programming
Scheduled programs
Zero offsets via G-codes
Custom fixed cycles
Fixed drilling cycles (live tool)
User Task 1
Program notes
Floppy disk input/output
Tooling
Spindle VAC motor drive
MacMan
(Machining Management)
OSP-WinX
Threading
OSP-E100L CNCOptional Specifications
Interactive Functions
One Touch IGF-XL (including LAP4 and Real 3D)
One Touch IGF-XL for multifunction machines (includes LAP4 and Real 3D)
Programming
Lathe auto programming (LAP4)
Circular threading
User Task 2 Sub-programs, math functions, logic operations
I/O variables, eight each (including above)
Tool offset (Standard: 32 sets) Tool offset: 96 sets
Tool wear compensation
Common variables: 1000 (Standard: 200)
Thread matching (spindle orientation required)
Threading slide hold (G34, G35)
Coordinate conversion
Profile generation
Flat turning
Programming Capacity
Program storage 512 KB (1280 m) (4200 ft)
Standard: 128 KB (320 m) 1024 KB (2560 m) (8400 ft)
(1050 ft) 4096 KB (10240 m) (33600 ft)
Operation buffer 512 KB (1280 m) (4200 ft)
Standard: 128 KB (320 m)
Monitoring
Real 3D simulation
Cycle time over check
Load monitor (spindle, feed axis)
Tool life management
Operation end buzzer
Chucking miss detection
Work counters Count only, ( ) pieces
Cycle stop, ( ) pieces
Start disabled, ( ) pieces
Hour meters Power ON
Spindle rotation
NC operating
NC operation monitor (includes counter and monitoring function)
NC work counter (stops at full count with alarm)
Operation end lamp (yellow)
Alarm lamp (red)
Status display with 3-color signal tower Type C [Type A, Type B]
Gauging
In-process work gauging
Z-axis auto zero offset (touch sensor)
C-axis auto zero offset by touch sensor
RS-232-C Standard channel
Additional channels
Set levels (5-level, 7-level)
BCD
CEJ MATIC (export specification)
RS-232-C (includes dedicated channel)
Touch setter [M, A]
Size catcher A (without caliper)
B (with 150-mm (5.91-in.) caliper)
External I/O, Communication Functions
OSP browser
IT Plaza network *
(DNC-T3)
Additional RS-232-C channel [1 chan, 2 chan]
(Standard specs iinclude 1 channel)
RS-232-C Maker
connecting cable Type
RS-232-C Maker
connecting cable Type
DNC–B (includes dedicated channel)*
DNC–C1 (includes dedicated channel)*
DNC–C2 (includes dedicated channel)*
DNC–C3 (includes dedicated channel)*
DNC–RT *
Automated / Untended Operation
Spindle orientation, electric
Auto power shutoff M02, alarm
Warmup function (by calendar timer)
Tool retract cycle
External program A (pushbutton) 8 types
selections B (rotary switch) 8 stages
C1 (digital switch) BCD, 2-digit
C2 (external inpu) BCD, 4-digit
Okuma loader (OGL) interfaces
Third party robot TYPE B (machine)
and loader TYPE C (robot and loader)
interface * TYPE D
TYPE E
Bar feeders Bar feeder (main)
Interface only
Maker
Type
Cycle time Cycle time reduction
reduction functions* Chuck open/close during spindle rotation
Auto tailstock advance/retract during spindle rotation
High-Speed/high-Accuracy Functions
ABSOSCALE (XA,ZA) *
1/10-µm (0.00004-in.) control *
Pitch error compensation (XA, ZA)
Other Functions
Short circuit breaker
External M signals [2 sets, 4 sets, 8 sets]
Multifunction
machines
Gauging data
output
Post-process
work gauging
interfaces
IT Plaza set (requires
system link and cable
connections)
DNC link (requires
system link and
cable connections)
Note 1: NML: normal, 3D: Real 3-D, E: economy, D: deluxeNote 2: * Requires technical consultation and confirmation with machine specificationsNote 3: For lathes with M-functions (live tooling)
Included in machine specs
Included in machine specs
Included in machine specs
Included in machine specs
Included in loader specs
E D E D E D E D
Kit Specifications
NML 3DOne- TouchIGF-M
One- Touch
IGF
E D E D E D E D
Kit Specifications
NML 3DOne- TouchIGF-M
One- Touch
IGFNK
NK
NK: Non-kit specs
19
Installation drawing
Specification drawing
MACTURN350
Installation drawing
Specification drawing
MACTURN250
U.S.A.: Charlotte, Los Angeles, Detroit
• Dealers in North and South America: Approx. 50
Brazil: Sao Paulo
• Dealers in Europe: Approx. 30
• Dealers in Asia:Approx. 20
Germany: Krefeld, Stuttgart
Australia: Melbourne
China: ShanghaiSingaporeTaiwan: TaipeiThailand: BangkokIndonesia: JakartaMalaysia: Kuala Lumpur
OKUMA GLOBAL SUPPORT NETWORK
� Measurements listed in this brochure are in mm (in.) format with 25.4 mm = 1 in.; other units are as indicated.
185 (7.28)
NCCabinet
2540
( 100
)
2390
( 94.
09)
150
( 5.9
1)
701
( 27.
60)
Hyd unit (oil controller)
ATC magazine operation panel
560
( 22.
05)
Oil controller for coolant
3220 (126.77)
360(14.17)
1339.8 (52.75)
650
( 25.
59)
735
( 28.
94)
550(21.65)
900(35.43)
470(18.50)
520(20.47)
550(21.65)
Side disposalchip conveyor,coolant tankremoval space
460
( 18.
11)
130
500 514013703770 (148.43)
1053 (41.46) 2390 (94.09) 850 1695105
(4.13)610
(24.02)707
930560
(22.05)
132
Maintenance space
Upper HT turret30-tool ATC magazine
Chip bucket(Optional)
Chip bucket(Optional)
Chip bucket(Optional)
Chip conveyor,side disposal, L type
(Optional)
1780 (70.08)150(5.91)
250 (9.84)
1147
( 45.
16)
796
( 31.
34)
502
( 19.
76)
1200
( 47.
24)
1025
( 40.
35)
2900
( 114
.17)
2790
110 1666 (65.59)624
(24.57)701
(27.60)
205(6.07)
Rear disposalchip conveyorremoval space
Tank removal space
Chip conveyor,rear disposal, L type(Optional)
7226
7( 10
.51)
226
( 8.90
)
2640
( 103
.94)
2490
( 98.
03)
440
130
701
( 27.
60)
ATC magazineoperation panel
560
( 22.
05)
Coolant cooler
Lower turret
Upper HT turret
1860 (73.23)
360 (14.17)1530 (60.24)
1645
2700 (106.30) 900(35.43)
470(18.50)
520(20.47)
550(21.65)
Window Window
4560 (179.53) 1036 (40.79) 2490 (98.03)3247101350
560(22.05)
765
( 30.
12)
185 (7.28)
Maintenance space
1940 (76.38)
1207
( 47.
52)
44-tool ATC magazine
Power inlet, 2600 (102.36)from floor
Power inlet, 1100 (43.31)from floor
1780 (70.08) 150 (5.91)
640
( 25.
20)
1147
( 45.
16)
796
( 31.
34)
640
( 25.
20)
1445
1200
( 47.
24)29
50 ( 1
6.14
)
1648 (64.88)598(23.54)
701(27.60)
2nd-operation spindle
Operation panel
Chip conveyor,side disposal, L type
(Optional)
OKUMA Corporation, OGUCHI-CHO, NIWA-GUN, AICHI 480-0193, JAPAN • TEL (0587) 95-7825 • FAX (0587) 95-6074
When using Okuma products, always read the safety precautionsmentioned in the instruction manual and attached to the product.
This product is subject to Japanese government regulations under the Foreign Exchange and Foreign Trade Control Act with regard to strategic goods. When further transport of this product to another country is being considered, prior consultation with Okuma Corporation is required.
� The specifications, illustrations, and descriptions in this brochure vary in different markets and are subject to change without notice. Consult your local Okuma representative for specific end-user requirements. Pub No. MACTURN250/350-(1)-300 (Oct 2002) Printed in Japan
460
( 18.
11)
150 (
5.91)
244(9.61)
250 (9.84)
450(17.72)
396
( 15.
59)
19
Installation drawing
Specification drawing
MACTURN350
Installation drawing
Specification drawing
MACTURN250
U.S.A.: Charlotte, Los Angeles, Detroit
• Dealers in North and South America: Approx. 50
Brazil: Sao Paulo
• Dealers in Europe: Approx. 30
• Dealers in Asia:Approx. 20
Germany: Krefeld, Stuttgart
Australia: Melbourne
China: ShanghaiSingaporeTaiwan: TaipeiThailand: BangkokIndonesia: JakartaMalaysia: Kuala Lumpur
OKUMA GLOBAL SUPPORT NETWORK
� Measurements listed in this brochure are in mm (in.) format with 25.4 mm = 1 in.; other units are as indicated.
185 (7.28)
NCCabinet
2540
( 100
)
2390
( 94.
09)
150
( 5.9
1)
701
( 27.
60)
Hyd unit (oil controller)
ATC magazine operation panel
560
( 22.
05)
Oil controller for coolant
3220 (126.77)
360(14.17)
1339.8 (52.75)
650
( 25.
59)
735
( 28.
94)
550(21.65)
900(35.43)
470(18.50)
520(20.47)
550(21.65)
Side disposalchip conveyor,coolant tankremoval space
460
( 18.
11)
130
500 514013703770 (148.43)
1053 (41.46) 2390 (94.09) 850 1695105
(4.13)610
(24.02)707
930560
(22.05)
132
Maintenance space
Upper HT turret30-tool ATC magazine
Chip bucket(Optional)
Chip bucket(Optional)
Chip bucket(Optional)
Chip conveyor,side disposal, L type
(Optional)
1780 (70.08)150(5.91)
250 (9.84)
1147
( 45.
16)
796
( 31.
34)
502
( 19.
76)
1200
( 47.
24)
1025
( 40.
35)
2900
( 114
.17)
2790
110 1666 (65.59)624
(24.57)701
(27.60)
205(6.07)
Rear disposalchip conveyorremoval space
Tank removal space
Chip conveyor,rear disposal, L type(Optional)
7226
7( 10
.51)
226
( 8.90
)
2640
( 103
.94)
2490
( 98.
03)
440
130
701
( 27.
60)
ATC magazineoperation panel
560
( 22.
05)
Coolant cooler
Lower turret
Upper HT turret
1860 (73.23)
360 (14.17)1530 (60.24)
1645
2700 (106.30) 900(35.43)
470(18.50)
520(20.47)
550(21.65)
Window Window
4560 (179.53) 1036 (40.79) 2490 (98.03)3247101350
560(22.05)
765
( 30.
12)
185 (7.28)
Maintenance space
1940 (76.38)
1207
( 47.
52)
44-tool ATC magazine
Power inlet, 2600 (102.36)from floor
Power inlet, 1100 (43.31)from floor
1780 (70.08) 150 (5.91)
640
( 25.
20)
1147
( 45.
16)
796
( 31.
34)
640
( 25.
20)
1445
1200
( 47.
24)29
50 ( 1
6.14
)
1648 (64.88)598(23.54)
701(27.60)
2nd-operation spindle
Operation panel
Chip conveyor,side disposal, L type
(Optional)
OKUMA Corporation, OGUCHI-CHO, NIWA-GUN, AICHI 480-0193, JAPAN • TEL (0587) 95-7825 • FAX (0587) 95-6074
When using Okuma products, always read the safety precautionsmentioned in the instruction manual and attached to the product.
This product is subject to Japanese government regulations under the Foreign Exchange and Foreign Trade Control Act with regard to strategic goods. When further transport of this product to another country is being considered, prior consultation with Okuma Corporation is required.
� The specifications, illustrations, and descriptions in this brochure vary in different markets and are subject to change without notice. Consult your local Okuma representative for specific end-user requirements. Pub No. MACTURN250/350-(1)-300 (Oct 2002) Printed in Japan
460
( 18.
11)
150 (
5.91)
244(9.61)
250 (9.84)
450(17.72)
396
( 15.
59)
MACTURN250/350
Multifunction Machines