tm terex finlay telematics system i100rs impact … · 2017. 11. 2. · terex finlay telematics...
TRANSCRIPT
69
R
SPECIFICATION:Rotor Size: Ø860mm x 860mm (Ø34” x 34”)
Net Power: Tier 3 / Stage IIIA: Caterpillar C7.1 Acert 186kW (250hp)
Tier 4F / Stage IV: Caterpillar C7.1 205kW (275hp)
Portability: Tracked
Operating Weight: 33,950kg* (74,847lbs*)
*With side conveyor and twin pole magnet fi tted
I-100RSTM
TEREX FINLAY TELEMATICS SYSTEM
I-100RSIMPACT CRUSHER
70
R
HOPPER / FEEDERHopper capacity: 2.3m³ (3.01yd³)
Feed height: 3.2m (10’ 6”)
Material: 8mm wear resistant steel
Width at rear: 2.26m (7’ 5”)
Vibrating Grizzly feeder (VGF): 3.27m x 800mm (10’ 9” x 32”)
VGF tine aperture: 25mm Standard
VGF wire mesh aperture: 30mm Standard
Speed: variable, 450 - 850 rpm
SPECIFICATION
IMPACT CHAMBERRotor diamater: Ø860mm (34”)
Rotor width: 860mm (34”)
Inlet opening: 860mm x 610mm (34” x 24”)
Rotor speed Range: 700 rpm - 930 rpm
Maximum Feed Size: Dependant on application 350mm Cube Approx
Drive arrangement: Direct drive via clutch
Twin Apron
Maximum apron settings: 120mm Primary, 55mm Secondary
Minimum apron setttings: 40mm Primary, 20mm Secondary
Rotor Confi guration: 4 bar rotor, 2 high / 2 low standard
Hydraulic overload protection
Hydraulic apron setting assist
Blowbar options: Martensitic (standard), Ceramic & High Chrome
POWERPACKTier 3 / Stage IIIA: Caterpillar C7.1 Acert
Engine Power: 186kW (250hp)
Engine Speed: 1700-2100 rpm
Tier 4F / Stage IV: Caterpillar C7.1
Engine Power: 205kW (275hp)
Engine Speed: 1700-2100 rpm
MAIN CONVEYORBelt Width: 900mm (36")
Belt Spec: plain
Working Angle: 22°
Speed: 95 - 110 m/min
Full length main conveyor with impact bars at feed point
Main conveyor can be lowered hydraulically for maintenance
Dust suppression: fi tted with hose and spraybars as standard (no
pump supplied)
Discharge Height: 3.25m (10' 8")
Stockpile capacity: 51m³ (66.7yd³) @ 40°
Hopper
Cat Engine
Main Conveyor
Impact Chamber
Hopper
71
SCREEN BOXTop deck: 2.44m x 1.2m (8’ x 4’)
Tensioning top deck: Side Tension
Drive: Hydraulic Motor
Screen Angle: 20°
Screen Speed: 1100 rpm
Screen can be lowered to a horizontal position for mesh changing and
general service access
Screen and Fines can be quick detached if not required
Total screening area: 32ft2
OVERSIZE TRANSFER CONVEYORBelt width: 500mm (20”)
Belt spec: Plain
Working Angle: 20°
Speed: Adjustable
Hydraulically folds for transport
RE-CIRCULATING CONVEYORBelt width: 500mm (20”)
Belt spec: Plain
Speed: Adjustable
Working Angle: 17°
Hydraulically folds for transport
TANK CAPACITIESHydraulic Tank: 350 litres / 77 UK gal / 92 US gal
Fuel Tank: 400 litres / 88 UK gal / 105 US gal
BY-PASS CONVEYOR - OPTIONALBelt Width: 500mm (20”)
Belt Spec: plain
Working Angle: 25°
Speed: 60 - 70 mpm
Hydraullically folds for transport
Discharge Height: 2.03m (6' 8")
Stockpile capacity: 13.8m³ (18yd³) @ 40°
By-pass ConveyorMAGNETIC SEPERATOR (OPTIONAL)Belt Width: 750mm (30”)
Drum Centres: 1.49m (58”)
Belt spec: cleated
Drive: Hydraulic
Magenetic Seperator
Oversize Transfer Conveyor
Re-circulating Conveyor
Screenbox
I-100RS
72
CONTROL SYSTEMSAdvanced CANBUS compliant system
Large color display screen
Simple operating modes with menu driven graphic user interface
- Track mode: for moving machine
- Manual Mode: for manually starting machine
- Automatic Mode: For automatically starting machine in
predetermined sequence
- Language Mode: To select required language
- Test Mode: to test run individual components
- Engine Diagnostic: showing engine information e.g. hours, rpm, etc.
- Confi guration Mode: For setting individual components
Detachable doglead control for tracking
Radio remote control (optional)
Lockable compartment
Emergency stops: 6 off
Control System
UNDERCARRIAGEShoe Width: 400mm (16")
Sprocket Centres: 3.7m (12' 1")
Track Speed: 0.6 km/h
Gradeability: 25°
CHUTESHeavy duty inlet chute with bolt-up construction, and liner plates
By-pass chute with selectable discharge fl op gate, to either by-pass
conveyor or main conveyor
TOOL BOXMounted lockable toolbox
Tool Kit and fl ogging spanners
Grease gun
ManualsUndercarriage
R
Remote Control Unit (Optional)
REMOTE CONTROL UNIT (OPTIONAL)Full function radio remote unit
Machine can be switched from crushing mode into track mode,
moved and be switched back to operating mode from remote control
unit
Primary apron remote hydraulic release
Feeder stop / start
PLATFORMSGalvanised catwalks and ladders for full maintenance and service
access
Catwalks on right hand side
Compact folding for transport
Platforms
73
I-100RS
TM
STANDARD FEATURES
ENGINE:Tier 3 / Stage IIIA: Caterpillar C7.1 Tier 3 ACERT 186kW (250hp)
Engine
Tier 4 Final / Stage IV : CAT C7.1 - 205kW (275hp)
IMPACT CHAMBER:Terex CR004 Impact chamber c/w full hydraulic apron
setting
4 bar rotor - Martensitic blow bars 2 High & 2 Low
Direct Drive via Clutch
Please contact the sales department for blowbar options
HOPPER / FEEDER:Fixed Hopper c/w vibrating feeder
Stepped grizzly feeder with integral pre-screen, standard35mm Tines spacing
Mesh aperture on grizzly feeder: 30mm
MAIN CONVEYOR:Belt width: 900mm (36”)
RS COMPONENTS:8’ X 4’ Single Deck Screen - supplied with 40mm mesh asstandard unless otherwise stated
Fines Conveyor 1.2m belt - hydraulically folding for transport
Transfer Conveyor 500mm belt - Hydraulically folding fortransport
Recirculating Conveyor 500mm Belt - Hydraulically foldingfor transport
Screen, Fines & transfer conveyor can be removed as singlecomponent
AUXILARY CONVEYORS:Piped for overband magnet
CLIMATE SPEC:Standard Oils - (Recommended for ambient temperaturesbetween -5 to +30°C)
DUST SUPRESSION:Piped for dust supression c/w Spraybars
ELECTRICAL:Emergency stops
Hand Held Track Control Set with Connection Lead
T-Link Telemetry System fi tted c/w 3 years data subscription
GENERAL:Safety Guards in Compliance with Machinery Directive
Single Speed Tracks
Optional spacing on grizzly, 35mmTines/46mm Tines/40mmPunch Plate & 60mm Punch Plate
Optional Spacing on Mesh under Grizzly - 10/20/40/50mm
- please specify aperture in additional information area
Belt weigher on main conveyor
Undercrusher vibratory feeder c/w shortened main conveyor
By-pass conveyor- 500mm beltwidth
Twinpole over band magnet (c/w stainless steel skirting &stainless steel discharge chute )
Twinpole heavy duty overband magnet (skirting & chute asabove) (please check leadtime)
Hot climate oils - (Recommended for ambient temperatures
between +15 to +50°C)
Cold climate oils - (Recommended for ambient temperatures
between -20 to +30°C)
Radio remote System
Control Panel Positive Pressurisation
Lighting mast (check leadtime)
Electric Re-Fuelling Kit
Special paint (if different from Finlay Orange RAL2002).
RAL must be specified*
OPTIONAL EQUIPMENT
74
By-Pass Conveyor (Optional) u Belt Width: 500mm (20”)
u Belt Spec: plain
u Working Angle: 25°
u Speed: 60 - 70 mpm
u Hydraullically folds for transport
u Discharge Height: 2.03m (6’ 8”)
u Stockpile capacity: 13.8m³ (18yd³) @ 40°
Main Conveyoru Belt Width: 900mm (36”)
u Belt Spec: plain
u Working Angle: 22°
u Speed: 95 - 110 m/min
u Full length main conveyor with impact bars at feed point
u Main conveyor can be lowered hydraulically for maintenance
u Dust suppression: fi tted with hose and spraybars
as standard (no pump supplied)
u Discharge Height: 3.25m (10’ 8”)
u Stockpile capacity: 51m³ (66.7yd³) @ 40°
Hopper / Feederu Hopper capacity: 2.3m³ (3.01yd³)
u Feed height: 3.20m (10’ 6”)
u Material: 8mm wear resistant steel
u Width at rear: 2.26m (7’ 5”)
u Vibrating Grizzly feeder (VGF):
3.27m x 800mm (10’ 9” x 32”)
u VGF tine aperture: 25mm Standard
u VGF wire mesh aperture: 30mm Standard
u Speed: variable, 450 - 850 rpm
Re-Circulating Conveyor u Belt width: 500mm (20”)
u Belt spec: Plain
u Working Angle: 17°
u Speed: Adjustable
u Hydraulically folds for transport
Screen Boxu Top deck: 2.44m x 1.2m (8’ x 4’)
u Tensioning top deck: Side Tension
u Drive: Hydraulic Motor
u Screen Angle: 20°
u Screen Speed: 1100 rpm
u Screen can be lowered to a horizontal position for
mesh changing and general service access
u Screen and Fines can be quick detached if not required
u Total screening area: 32ft2
Oversize Transfer Conveyor u Belt width: 500mm (20”)
u Belt spec: Plain
u Working Angle: 20°
u Speed: Adjustable
u Hydraulically folds for transport
Impact Chamberu Rotor diamater: Ø860mm (34”)
u Rotor width: 860mm (34”)
u Inlet opening: 860mm x 610mm (34” x 24”)
u Rotor speed Range: 700 rpm - 930 rpm
u Maximum Feed Size: Dependant on application
350mm Cube Approx
u Drive arrangement: Direct drive via clutch
u Twin Apron
u Maximum apron settings: 120mm Primary, 55mm Secondary
u Minimum apron setttings: 40mm Primary, 20mm Secondary
u Rotor Confi guration: 4 bar rotor, 2 high / 2 low standard
u Hydraulic overload protection
u Hydraulic apron setting assist
u Blowbar options: Martensitic (standard), Ceramic
& High Chrome
Powerpacku Tier 3 / Stage IIIA: Caterpillar C7.1 Acert
Engine Power: 186kW (250hp)
Engine Speed: 1700-2100 rpm
u Tier 4F / Stage IV: Caterpillar C7.1
Engine Power: 205kW (275hp)
Engine Speed: 1700-2100 rpm
Undercarriageu Shoe Width: 400mm (16”)
u Sprocket Centres: 3.7m (12’ 1”)
u Track Speed: 0.6 km/h
u Gradeability: 25°
75
I-100RS
WORKING DIMENSIONS
MACHINE WEIGHT:
TRANSPORT DIMENSIONS
15.8m (51’ 9”)
14.8m (48’ 7”) 3m (9’ 10”)
3.2m
(10
’ 6”)
33,950kg* (74,847lbs*) *With side conveyor and twin pole magnet fi tted
5.5m (18’)
3.86
m (
12’ 8
”)
For further information on specifi c machine weight confi gurations please consult Terex Finlay
76
R
www.terexfi nlay.com
Effective June 2014. Product specifi cations and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only.
Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise
act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex GB
Ltd. makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and
other countries. All rights are reserved. Terex® is a registered trademark of Terex Corporation in the USA and many other countries. Copyright 2010 Terex GB Ltd.
Follow us on: