titan-rtr (ready to run)
DESCRIPTION
OFNA Titan Monster TruckTRANSCRIPT
INSTRUCTION MANUAL
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL.
KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.
REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel20%
Cross Wrench#17109 $3.95
You need to get batteries for the radio transmitter and the car receiver packs.• Radio TX needs (8) eight AA batteries.• Car/Truck needs (4) four AA Ni-cad batteries, Alkaline type batteries will work, but braking will be reduced. The best is to use a 5 cell hump pack for increased voltage..
Recommended Option:You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600AE). This will give more run time. OFNA #10212
You will need to buy a few items to start the engine and run the car.• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007). Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..• #10163 - Bottle, spout top• #10218 - Red “C” size glow heater
#10212 NiHm Hump Pack,see charger 10214.
10214Over-niteCharger
TOOLS NOT INCLUDED IN KIT INCLUDED WITH KIT
Shock Oil
1.5mm Hex Wrench
Grease BoxPhillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Super Glue
Precision Caliper
2.5mm Hex Wrench
3mm Hex Wrench
5mmHex Wrench
7mm and 5.5mmHex Wrench
Wheel Nut Wrench
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe rusting.• Clean oil and dirt from chassis with a degreaser.and good experience you must observe a few rules. This
kit is extremely fast, easily over 40MPH, and can seriously Precautions
injure someone if you are not careful. • This kit is not a toy. Always run car with a second
person as a spotter and pitman.Where to run car?• Any running area you choose must be dry. Do not run
• Hot Parts - The pipe, manifold, engine and head are very car near any water or wet dirt.
hot and will cause burns.• Do not run on public streets. It is very easy to have the
car run over or damaged by hitting the curb. • Rotating Parts - Keep hands away from the drive train, • Do not operate car in tight confined places. The car is
wheels, and engine when engine is running.very fast and will easily hit something.• Do not run near people or animals. • Radio - Check batteries life before running the car. If
radio does not have full control of the car with steering • Due noise, you will want to consider the surrounding
and/or throttle/brake do not run until corrected. Failure to area when operating the car.
correct this will result in possible injury and damage to the • Do not operate the car at night. You will not be able to
car or property.drive it without hitting something.• Do not operate the car indoors. Engine exhaust is not
• Glow fuel - Do leave the glow fuel unattended with the lid healthy.
off. Fuel contains Methanol and Nitro Methane and is
flammable and poisonous.Glow Fuel• Glow fuel is poisonous!
Store fuel in cool ventilated location. Refer the glow fuel • Glow fuel is flammable!• Do not leave in fuel bottle with lid off at any time. label for additional precautions.• Do not use any fuel other than glow fuel in this engine.
• Car Fuel tank - Never store fuel in car tank, it will ruin the First Time Starting the Engine engine if left in tank.Caution! When starting engine make sure the following is
observed. • Always turn off the car BEFORE turning off radio.• Set engine Master needle to 3 turns (rich setting)• Do not do this alone, get an experienced friend to help at • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
first. ISSUE.• Fill fuel tank, try not to spill fuel. Do not spill fuel on
receiver IF YOU DO NOT BREAK-IN ENGINE • Hold car off the ground, so it will not runaway when first
CORRECTLY, MAINLY AT LOW RPM, starts• Turn on Radio and check the linkage before starting YOU WILL BREAK THE CONNECTING engine.
ROD!• Turn on car receiver battery switch.• Always have an air filter on the carburetor to keep dirt
out. FAILURE TO NOT READ AND Engine Break-in
FOLLOW BREAK-IN ENGINE • See Engine Page.
Emergency Stopping Engine When Running INSTRUCTIONS WILL VOID • Remove air filter and cover carb. intake.• Squeeze fuel line and hold until engine stops. WARRANTY!• With a rag, cover exhaust outlet.
Storing Car After RunningCHECK RADIO SETTING AND • Remove fuel from tank and fuel lines
• Turn off radio in carLINKAGE BEFORE STARTING• Put a few drops of after run in engine to keep it from
The car is very fast
and will too easily hit someone.
AB
C
CHECKING ENGINE THROTTLE
* Insert into transmitter.
1. Insert AA batteries into transmitter (8 Pcs).2.Turn on transmitter.3.Turn on receiver.4.Center throttle trims as shown .
A B C
1. Pull Full Throttle. 1. Push trigger to full brake position.2. Adjust alum. Stopper to increase or decrease the brake.
Idle Position (A)
Brake (C)
Full Throttle (B)
* Align throttle servo same as shown.
A
B
C
• Full brake arm position. Spring compresses forward and brake rods pull brake levers.
• Full throttle arm position. Spring rod pulls throttle barrel open and brake rods release pressure on brake cams.
IMPORTANTCHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR
Insert 8 pcs AA batteries into transmitter.
Note: Battery life is short when using Alkaline batteries. For safety, we recommend checking Alkaline batteries after 30 minutes. Battery strength affects radio range; in the case of a monster truck, it affects brake power. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty.
To increase run time, upgrade receiver batteries to AA Ni-Cad or NiMH type. But, the most important step you can make, “is to always use fully charged or fresh batteries when running your car”.
The beat performance is achieved by changing to a 6 volt 5 cell hump pack, OFNA #10212. The servo have their greatest power at 6 volts.
Radio shown may vary depending on availability. Therefore radio pictured on box may or may not be the same.
40003Diff. Case
40017Front and Rear Gear Boxes
PLASTIC PARTS
36901Front Knuckles, Pivot Ball
40031Servo Saver Plastic Tree
40056Plastic Shock Parts Tree
40201Front and Rear Upper Arms
31304Rear Hub,Pivot Ball
40202Front and Rear Lower Arms.
40204Chassis Skip Plate
40203Shock Tower part
40205Arm Holder/Center Diff. Mount /Side Chassis BracePlastic Parts
40207Bumper Mounts
40206Chrome Roll Bar Plastic Parts(w/spot light)
40040Center Diff Mount Tree
ASSEMBLY OF THE DIFFERENTIAL
40006Cap Joint
40006Cap Joint
307014x4mmSet Screw
400102.5x13.8mmPin
400102.5x13.8mmPin
360538x16mmBearing
360538x16mmBearing
360538x16mmBearing
360538x16mmBearing
( Builds two differentials for front and rear.)
40009P6 O-Ring
40009P6 O-Ring
400126x15mmWasher
400126x15mmWasher
40004Diff.Gear(Large)
40004Diff.Gear(Large)
40003Diff. Case
40004Diff. Gear(Small)
40004Diff. Gear(Small)
Option:49001 - Gears, HD Steel
Note: Diff must always usegear shim. If no shims are used,we have found that diff may break.
307794 x 10mm washer
307794 x 10mm washer
307794 x 10mm washer
307734mmCross pin
307734mmCross pin
Note:- Add grease into diff case before closing.
*Put the O-ring in inside of the diff. case and press it flush against the bottom.
40011Diff. Gasket
3x12mmFlat HeadTapping Screw
40214LargeBevel Gear
40214LargeBevel Gear
ASSEMBLY OF THE GEAR BOX( Builds two gear box for front and rear.)
40017Gear Box
40017Gear Box
4901213T Bevel Gear( l)Smal
4002413x16x0.2mmShim
Note: ALWAYS USE OR ADD MORE!Adjust gear mesh by using #40024 shims. Add shim to either side for mesh. Recommend atight feel but not binding or loose.
No need to add shims to this side. Loosening gear mesh will only cause gear to skip.
ASSEMBLY OF THE FRONT ARMS HOLDER
4X15MMTapping Screw( Small Head)
4X45MMTapping Screw( Small Head)
40022Front Lower ArmHolder (Front/Alum.)
Screw Cement900265x5mmSet Screw
36730Cap Joint
4x16mmFlat HeadTapping Screw
4x16mmFlat HeadTapping Screw
40015Front Lower ArmHolder (Rear/Plastic)
40015Front Upper ArmHolder ( Rear/ Plastic)
3x12mmTapping Screw
4x15mmScrew(Small Head)
40205Upper ArmHolder
Option:49002CNC 7075 Front Lower Arm Holder
ASSEMBLY OF THE FRONT KNUCKLE ARMS
36905Plastic Washer
36905Plastic Washer
3690314mm Steering Ball
3690314mm Steering Ball
3690414mmAlum. Nut
3690414mmAlum. Nut
( Left-Side )
( Right- Side )
36901Ball TypeKnuckle Arm
36901Ball TypeKnuckle Arm
40242Misc. Screws and Hardware
Note:Thread nut into knuckle straight, do not cross thread.Do not over tight Nut. Adjust nutfor smooth movement. If tootight, knuckle will not turn.
Screw Cement
Screw Cement
ASSEMBLY OF THE FRONT CVA JOINTs
36052mm CVA Joint
360528mm CVA Joint
360538x16mmBall bearing
360538x16mmBall bearing
40245Hex Hub,Orange
Spare:15073Nut, Hex Hub,Orange
360538x16mmBall bearing
360538x16mmBall bearing
360548mm Alum.Wheel Hub
360552.5x17mmPin
360552.5x17mmPin
900265x5mmSet Screw
5x5mmSet Screw
900213mmE-Ring
900213mmE-Ring
900202.5mmE-Ring
900202.5mmE-Ring
40226Upper Arm Shaft
40023Lower Arm Shaft
40201Upper Arm
40202Lower Arm
ASSEMBLY OF THE FRONT SUSPENSION ARM
4X16mmFlat HeadScrew
40235Lower Chassis
40239Servo SaverPost
4x10mmFlat HeadScrew
* Insert the drive shaft into diff. cap joint before assembly.
ASSEMBLY OF THE SERVO SAVER
ASSEMBLY OF THE SERVO SAVER UNIT
ASSEMBLY OF THE SERVO SAVER ONTO LOWER CHASSIS
40035Alum.Servo SaverTube
40031Servo Saver Horn Plastic
40031Servo Saver Horn Plastic
40033Servo Saver Spring
40034Servo SaverAdjuster
40037Steering PlateHex Screw
40037Steering PlateHex Screw40031
Servo SaverPlastic Bushing
40031Servo SaverPlastic Bushing
4x8mmPlastic Bushing4x8mm
Plastic Bushing
40032Servo SaverConnecting Plate
49006CNC Servo SaverConnecting Plate
ASSEMBLY OF THE STEERING RODS
ASSEMBLY OF THE SERVO SAVER AND STEERING RODS
400393mmCone Washer
353133mmNylon Nut
353133mmNylon Nut
353133mmNylon Nut
368507mmBall End
368507mmBall End
36700SteeringBall End
367904x46mmTurnbuckle
* Made two steering rods for left and right hand side.
3x15mm Screw
3x12mm Flat HeadScrew
3x12mm Flat HeadScrew
Option: 49014 Servo Saver Alum. Tube ( Ball bearing Type )
* Place the servo saver into the servo post.
* Take the 4x8mm Plastic Flange bushing and Plastic Bushing from servo saver plastic parts tree
368605x35mmTurnbuckle
40201Upper Arm
368507mm Ball
366907mmPlastic Ball End
ASSEMBLY OF THE REAR UPPER ARM
3130711mmBall & Screw
31304Rear Hub( Ball Type )
31305Plastic Washer
3130612mmAlum. Hex Screw
Screw Cement
20245Wheel Hub,Orange
360552.5x16.8mmPin
360818mmRear Wheel Axle
360538x16mmBall bearing
360538x16mmBall bearing
40215RearDrive Shaft (91.5mm)
40215Rear Drive Shaft (91.5mm)
400234mmLower Arm Shaft
307023x25Hex Screw
35313M3 Nylon Nut
900202.5mmE-Ring
900202.5mmE-Ring
900213mmE-Ring
3mmE-Ring
Upper ArmWasher
ASSEMBLY OF THE REAR HUB
ASSEMBLY OF THE REAR HUBAND SUSPENSION ARMS INTO GEAR BOX
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
900265x5mmSet Screw
*Builds two arms for left and right hand side.
*Builds two hubs for left and right hand side.
8mm
*Insert the rear drive shaft before assembly the rear lower arm. 40202
Rear Lower Arm
90021
Note: This Axles part is not neededif your kit has CVA joint for rear instead.
ASSEMBLY OF THE FRONT GEAR BOX ONTOUPPER CHASSIS
4X16mmFlat HeadTapping Screw
35314M4Nylon Nut
35314M4Nylon Nut
35314M4Nylon Nut
4x15mmScrew
4x15mmScrew
40205Center Diff. Mount
ASSEMBLY OF THE FRONT SHOCK TOWER
3x16mmTapping Screw
4x25mmScrew
4x16mmTapping Screw
40040Center BraceMount ( Front )
4x10mmFlat HeadScrew
40234Main Chassis
40203Shock Tower
4x16mmFlat Head Tapping Screw
4x10mmFlat Head Screw
Rear Gear BoxAssembly
3x15mmTapping Screw
40203Shock Tower
40040Center BraceMount ( Rear )
35314M4Nylon Nut
ASSEMBLY OF THE TWO SPEED GEAR
ASSEMBLY OF THE REAR GEAR BOX ONTOUPPER CHASSIS
ASSEMBLY OF THE REAR SHOCK TOWER
3524545T Spur Gear
3524949T Spur Gear
3522918mmE-Ring
352308x12mmFlange Ball bearing
352308x12mmFlange Ball bearing
352262nd Spur GearHolder
352251st Spur Gear Holder
35228Alum. Nut(Anti-clockwise)
4x25Screw
4x15Tapping Screw
Option:40241 - 2-Speed Trans. W/Steel Gears.40247 - Gear, Steel 47T40251 - Gear, Steel 51T
402193X13.8mmPin
402193X13.8mmPin
ASSEMBLY OF THE SLIPPER CLUTCH
ASSEMBLY OF THE TWO SPEED TRANSMISSION
30170Brake Joint
360538x16mmBall bearing
360538x16mmBall bearing
360538x16mmBall bearing
4020828T HelicalGear
402188x12x1mmWasher
* Use 3 pcs.
900265x5mmSet Screw
900265x5mmSet Screw
900265x5mmSet Screw
352272 SpeedClutch Cam
40217Center GearShaft
1st GearAssembly
2nd Gear Assembly
Type 1 : Use for slipper clutch.
Type 2 : Disable Slipper
Add pin (40219) onto shaftto lock out slipper function.
40220Slipper ClutchShaft
40223Slipper Clutch Plate
40223Slipper Clutch Plate
40224Slipper ClutchGasket
40224Slipper ClutchGasket
4020938THelical Gear
ASSEMBLY OF THE BRAKE PADS
36660Brake ShoePlate
36661Brake PadLinings
Front Middle Rear
* Remove the double-side tape before assembly
40045Brake PadAdjustment Screw
Brake Pad Assembly
40044Brake PadSpring
40044Brake PadSpring
Less 2.5mm
* Sett the adjustment screw to keep the space of the brake pad less 2mm.
36730Cap Joint
Screw Cement
360538x16mmBall bearing
4x4mmSet Screw
900265x5mmSet Screw
40222Slipper ClutchSpring
40221Slipper ClutchAdjuster
36730Cap Joint
40040Center Diff.Mount
* Don't use Screw cement in 4x4mm set screw.
Add pin (40219) onto shaftto lock out slipper function.
ASSEMBLY OF THE 2 SPEED TRANSMISSION INTO CENTER MOUNT
36650Brake Disk
40040Center Diff.Mount
40040Center Diff.Mount
40040Center Diff.Mount
40216Center Drive Shaft( Long/93mm )
40216Center Drive Shaft( Long/93mm )
40216Center Drive Shaft(Short/86.5mm )
40216Center Drive Shaft(Short/86.5mm )
* Put the brake disk into the brake cap joint before assembly the center diff. mount.
40225Center Diff. MountPost
40225Center Diff. MountPost
* Put the center diff. mount post through the center diff. mount.
ASSEMBLY OF THE BRAKE CAM AND CENTER DIFF. MOUNT PLATE
30213Brake Cam
30211Brake,Bushing
Option:30212Brake5x8mmBearing
3x15mmScrew
40237Alum. Center Diff. Plate
40237Alum. Center Diff. Plate
3x3mmSet Screw
30171Brake Level
*Screw in 3x15mm screw for temple use.
* Put the center drive shaft before assembly the slipper clutch unit.
35313M3Nylon Nut
35313M3Nylon Nut
3x15mmFlat HeadScrew
3x16mmFlat HeadScrew
3x16mmFlat HeadScrew
3x16mmFlat HeadScrew
3x16mmFlat HeadScrew
3x25mmCap Screw
3x15mmScrew
3x15mmScrew
ASSEMBLY OF THE UPPER CHASSIS BRACE
4021243.9mmChassis Stiffener( Rear/lowe/Long)
ASSEMBLY OF THE LOWER CHASSIS BRACE
4021335.7mmChassis Stiffener( Front/lowe/Short)
304116mm Ball
304116mm Ball
304116mm Ball
304116mm Ball
304116mm Ball
304116mm Ball
402006mm PlasticBall End
402006mm PlasticBall End
402006mm PlasticBall End
402006mm PlasticBall End
402006mm PlasticBall End
402006mm PlasticBall End
ASSEMBLY OF THE UPPER BRACEINTO CHASSIS
40203CenterBrace mount
4021095.5mmChassis Stiffener(Rear/Upper/Long)
4021187.5 mmChassis Stiffener(Front/Upper/Short)
3x15mmTapping Screw
3x15mmTapping Screw
3x15mmTapping Screw
3x15mmTapping Screw
40207BumperSupport
40207BumperSupport
40207BumperSupport
ASSEMBLY OF THE BUMPER SUPPORT PARTS
ASSEMBLY OF THE SHOCK ABSORBER* Made eight shocks for front and rear use.
40076Shock Body
400907mm E-Ring
40090
Washer(2mm)
40090
Washer(1mm)
400903.5mm O-Ring
4005914.7mmO-Ring
40054Shock Shaft
2.6x5mmWasher
32235Shock Piston
400602.5mmNylon Nut
3. Pull down piston, attach pressure top and shock oil overflow with tissue paper.
1. Pull down piston and pour oil into shock cylinder.
*Move Slowly.
32033Pressure Top
40093Shock Cap
*Fit into the groove.
down.
UP
ASSEMBLY THE DUST COVER AND SHOCK SPRING
40058Shock Shaft Dust Cover
2.To remove air bubbles by slowly moving piston up and down.
FILL THE SHOCKS WITH OIL
* Push 6mm ball joint into ball end.
40243Shock Spring,Black
40063Spring Holder
304116mm Ball
4005914.7mm O-Ring
* Fit the o-ring into groove.
40056Shock Plastic Rod End
49041Alum.Adjust Nut,Orange
ASSEMBLY OF THE FRONT AND REAR SHOCKINTO SHOCK TOWER
3X15mmScrew
3X15mmScrew
3X15mmScrew
3X15mmScrew
3X15mmScrew
3X15mmScrew
3X15mmScrew
3X15mmScrew
3x8mmWasher
3x8mmWasher
3x8mmWasher
3x8mmWasher
304116mm Ball
304116mm Ball
304116mm Ball
304116mm Ball
Shock Assembly
4x20mmFlat HeadTapping Screw
4x20mmFlat HeadTapping Screw
3x12mmTapping Screw
3x12mmTapping Screw
40204Skip Plate
40204Skid Plate
3x20mmFlat HeadTapping Screw
3x20mmFlat HeadTapping Screw
3x20mmFlat HeadTapping Screw
3x20mmFlat HeadTapping Screw
ASSEMBLY OF THE FRONT AND REARCHASSIS SKIP PLATE
( FRONT )
(REAR )
* Put the M4 nylon nut into the side chassis brace plastic before assembly next step.
for
ASSEMBLY OF THE SIDE PLATE MOUNT
40205Side ChassisBrace Plastic 35314
M4 Nylon Nut
M4x10Flat HeadScrew
ASSEMBLY OF THE FUEL TANK
40066Fuel Tank
3x10mmScrew
3x10mmScrew
38120Alum. Fuel Tank Post
Fuel Nipple
Fuel Nipple
3x12mmScrew
3x12mmScrew
Assembly of the right and left hand side are the same.
4x15mmScrew
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
40202Alum. Side PlateFor Plastic Chassis Brace
ASSEMBLY OF TE CHASSIS STIFFENER PLATE
aSSEMBLY OF THE CHASSIS STIFFENER
35314M4Nylon Nut
35314M4Nylon Nut
35314M4Nylon Nut
4x15mmFlat HeadScrew
4x15mmFlat HeadScrew
4x15mmFlat HeadScrew
4x15mmFlat HeadScrew
40205Plastic Side ChassisBrace (Front)
40205Plastic Side ChassisBrace (Rear)
ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX
THROTTLE SERVO
40236Radio Tray
10274Servo Post
10274Servo Post
3x10mmTapping Screw
3x10mmTapping Screw
3x10mmTapping Screw
3x10mmTapping Screw
30560Antenna Pipe
Battery Case
Receiver
34032Receiver Box
34032Receiver BoxCover
10280Switch Cover
Switch
Screw
* Connect switch wire to receiver.
* Connect battery wire to receiver.
* Connect throttle wire to receiver.
Servo Post
Steering servo
3x10mmScrew
Assembly the steering rod same as shown.
401996mm Plastic Ball End
401996mm Plastic Ball End
304106mmBall & Socket
304106mm Ball
3x10mmScrew
3x10mmScrew
3x8mmSet Screw
Screw
* Use the screw provided from your servo.
* Use the screw provided from your switch.
3x10mmFlat Head Screw
3x10mmTapping Screw
10768Steering Servo Horn
10769Servo HornAdapter
ASSEMBLY OF THE RADIO TRAY ONTO CHASSISAND STEERING SERVO
* Put the receiver on the top of the battery case.
ASSEMBLY OF THE BRAKE LINKAGE
ServoMount
* Cut the shaded area as shown.
3x3mmSet Screw
3x3mmSet Screw
3x3mmSet Screw
3x3mmSet Screw
361402mmAdjust Mount
3x25mmScrew
2x4mmScrew
2x6mmWasher
2mmTie-RodEnd
2mm Rod2x8mmScrew
2mmNut
ThrottleSlider
2mmRod
10300Alum. Stopper
10300Alum. Stopper
10300Alum. Stopper
30530ThrottleBall End 3x10mm
Screw
10768Servo Horn
10769Servo HornAdapter
* Use the screw provided with your radio.
ASSEMBLY OF THE SERVO LINKAGEINTO THROTTLE SERVO
30800 - SERVO LINKAGE KIT, COMPLETE
304813x20mmHex Screw( 4 Pcs )
* Only use this 6.3mm tapered cone for threaded crank shaft with drive nut.
103307mm Tapper cone
10098SGClutch Nut
SG TypeCrank Shaft
304813mm Nylon Nut
304813mm Nylon Nut
30480Engine Mount
* Put the nylon nut into the groove of the engine mount.
10010Clutch Shoes
10102Clutch Spring
3x5mm Screw
3x8mm Washer 34110
5x10x4mmBall bearing
402445x9x0.3mmWasher
402445x9x0.3mmWasher
M-27BClutch Gear( 12T/16T)
Clutch Gear for Option
4023111T/15T
4023213T/17T
392425x8x2.5mmBall bearing( 2 Pcs )
402292-SpeedClutch Bell
ASSEMBLY OF THE 2-SPEED CLUTCH BELL
* Fit the flywheel using a pair of the plier and cross wrench.
10091Pilot Shaft
103296.3mmTapper Cone
ASSENBLY OF THE ENGINE MOUNT
100403 pin Wheel
Threaded CrankShaft
Notes:Non-Pull Start Engines...• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer.
• To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.
You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to tighten the clutch nut and mount the flywheel.
Force Pull Start Engine w/threaded shalf...• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn. This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.
#10040 (stock)3 PinFlywheel, Taper#100433 PinFlywheel, Fan
* Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. Using a screw driver as a lever, bend the small end of the clutch spring behind the clutch nut and press down to snap shoe in place.
* Fit the flywheel using a crosswrench or deep socket.
If engine turns when tightening,hold piston with large thick tie-wrapsand hard wood in exhaust port. Do not use metal, it will damage engine.
Options
Clutch Spring10100 - Springs, Polished, Med.10101 - Spring, Gray, Hard10102 - Spring, Black, Stock
Clutch Shoes, 3 shoe clutch10010 - Shoes, Carbon Material, Black10011 - Shoes, Alum. CNC Blue, Lite Weight10012 - Shoe, Alum. CNC Purple, Med. Weight
Option10799Flywheel Wrench
3 x 10mmTapping Screw
#10016Air FilterSpongeRefills
#10017 - Blue#10018 - Yellow#10019 - Rose10034 - ChromeFoam Air filters Unit
#10013 - Mount Wire
#10021 - Black#10027 - Yellow#10028 - Pink#10029 - BlueAir Filter Connector Nylon Strap
( Small )
Nylon Strap ( Small )
You must oil foam filter before use.Filter will not work if not oiled.
Clean with soap and water only.You will damage foam if washedif fuel!
ASSEMBLY OF THE AIR FILTER
10079Pressure Nipple
10180Silicone TubeNylon Strap
(Middle)
Nylon Strap(Middle)
31992Muffler
ASSEMBLY OF THEEXHAUST SYSTEM
* Contacts to the carburetor.
10016Air FilterSpongeRefills
10034Air FilterMount
10034Air FilterCover
Nylon Straps ( Small )
Nylon Straps ( Small )
10021Air FilterConnecter
3x10mmTapping Screw
10069Manifold,Seal
31991PolishedManifold
* Apply filter oil to the sponge before use.
*Put the manifold spring around the Engine.
ASSEMBLY OF THE AIR FILTER AND MANIFOLD10120SpringManifold
Option:10182Silicone Tube, Red10183Silicone Tube, Yel.10184Silicone Tube, Blue
Option:10078Pipe MountingPost, Alum.
Option:31991Polished, Manifold31992Polished, Tuned Pipe
ASSEMBLY OF THE ENGINE ONTO CHASSIS
10111Engine Mount
900265x5mmSet Screw
4x10mmFlat HeadScrew
35314M4Nylon Nut
40227Muffler Stay
101113mm Hex Screw for Engine Mount
* Snap the throttle ball end into the valve ball of the . carburetor
ASSEMBLY OF THE FUEL TUBE AND PRESSURE TUBE
*Connect to carburetor
*Connect to fuel nipple.
*Connect to muffler pressure nipple.
Fuel Tube
*Connect to fuel tank pressure nipple.
ASSEMBLY OF THE TIRES AND WHEELS OF THE RIGHT HAND SIDE
ASSEMBLY OF THE TIRES AND WHEELS OF THE LEFT HAND SIDE
* Make two tires for the right hand side. Make the both tires are in the same direction.
* Make two tires for the left hand side. Make the both tires are in the same direction.
86063Monster Tires
86063Monster Tires
86063Monster TireInner Sponge
86063Monster TireInner Sponge
86064 - White860654- ChromeMonster TireWheel
86064 - White860654- ChromeMonster TireWheel
ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLEAND REAR HUB
Tire and Wheel assembly
15073Wheel Nut
15073Wheel Nut
* Use the hex wrench come from your kit to secure your tires.
INSTANT GLUE
INSTANT GLUE
* Apply instant glue into the both side of the groove of the wheel.
* Apply instant glue into the both side of the groove of the wheel.
( FRONT )
( FRONT )
( REAR )
( REAR )
ASSEMBLY OF THE BODY POST
3X 15mmScrew
3X 15mmScrew
33011Body Post Set
33011Body SupportPlastic
33011Body SupportPlastic
31159Body Clip
31159Body Clip
31159Body Clip
,Orange
ASSEMBLY OF THE SPOT LIGHT ANDROLL BAR - p/n#40206
2X8mmScrew
Spot LightPlastic
40206Roll Bar Plastic
3x20mmTapping Screw
3x20mmTapping Screw
3x20mmHex Screw
* Put the spot light assemble into the groove of the roll bar.
M3Nylon Nut
3x8mmwasher
3x8mmwasher
3x10mmTapping Screw
3x10mmTapping Screw
3x8mmwasher
3x10mmTapping Screw
3x8mmwasher
3x8mmwasher
3x10mmTapping Screw
3x10mmTapping Screw
ASSEMBLY OF THE SPOT LIGHT AND ROLL BARONTO BODY
33060Truck Body
ASSEMBLY OF THE SIDE MIRROR AND ANTENNAONTO BODY
* Use the screw from inside of the body.
* Use the screw from inside of the body.
2x8mmScrew
2x6mmWasher
40206
Mirror Holder 40206
Side MirrorPlastic
40206Mirror
40206Antenna
4mmRing
4mmRing
40206Wipe
Assembly of the right and left hand side are the same.
Pre-Painted & Cut Bodies33061 - Red/Yellow Body33062 - Silver/Yellow Body33063 - Blue/Yellow Body
SETTING SHEET
ADJUSTING THE SHIFT POINTThe M-27 2-speed transmission allows the car to have morepunch out of the corners and higher top speed. We offer many different pinion and spur gear combinations which can be used for different tracks.
* Adjust the engine before adjusting the clutch shift timing. Adjust the engine as per engine instruction manual.
1. Once the engine adjustment have been completed, proceed to adjustment of the clutch shift timing. (Using a 2mm allen wrench to adjustment the clutch cam.) Note: Clockwise--------Shift timing will become slower. Anticlockwise---Shift timing will become quicker. 2. Adjust the clutch shift timing for your track conditions with 4x4mm set screw. As you tighten (Clockwise) the 4x4mm set screw , the shift timing will become slower. As you loosen (Anticlockwise ) the 4x4mm set screw, the shift timing will become quicker.
3. Set the shift timing to the track conditions while the car is running.
* Use a 2mm allen wrench to set the clutch cam.
* Use a 2.5mm allen wrench to set the toe-in and toe-out.
2mm Allen Wrench
Clockwise (Tighten)
Anti-clockwise (Loosen)
2 SPEED OPTION PARTS 2 SPEED PARTS
35249 49T Spur Gear
35248 48T Spur Gear
35247 47T Spur Gear
SPUR GEAR(1st):
Description 35225 1st Spur Gear Holder
35226 2nd Spur Gear Holder
35227 Clutch Cam Set
35228 Alum. Nut (Anti-Clockwise)
35229 18mm E-Ring
35230 8x12mm Flange Ball bearing
35231 8x10x3mm Alum. Ring
35222 Center Shaft
34110 5x10x4mm Ball bearing
35221 Clutch Bell
Description
35246 46T Spur Gear
35245 45T Spur Gear
35244 44T Spur Gear
SPUR GEAR(2nd):
Description
40231 11T/15T Gear
40230 12T/16T Gear
40232 13T/17T Gear
CLUTCH GEAR:
Description
IMPORTANT:The sum of the spur gear and clutch gear for 1st gear must be equal.The sum of the spur gear and clutch gear for 2nd gear must . be equal
Example:
1st gear 49+12=612nd gear 45+16=61 Must be equal
SPUR GEAR CLUTCH GEAR
48T/44T
(4 tooth difference)
49T/45T
11T/15T 12T/16T 13T/17T
Sh
ort T
rac
k
To
rqu
eT
op
Sp
ee
d
Lo
ng
Tra
ck
( STANDARD)
2 SPEED GEAR RATIO COMBINATIONS
*Notice the direction of the clutch cam.
Adjustment through this hole.
To Front
14T/18T
USA Parts No.
USA Parts No.
USA Parts No.
USA Parts No.
OFNA Racing-USATel:949-586 2910 Fax:949-586 8812
Made In Taiwan
0
0
0
0
+
+
+
+
-
-
-
-
Adjust the length of the front steering rod to change the toe angle.Making the steering rod longer will make the front tires become toe-in. The Response will be slower.Making the steering rod shorter will make the front tires became tor-out. The Response will be quicker.
ADJUSTMENT OF THE FRONT CAMBER
ADJUSTMENT OF THE REAR CAMBER
SET-UP OF THE FRONT WIDTH
0
0
+
+
-
-
* Use a 2.5mm hex wrench to adjust the length of the steering balls. This will make the front wider or narrower.
Adjust thesteering balls.
Adjust the upper steering ball to adjust the camber.
(Positive)
(Positive)
(Negative)
(Negative)
FRONT TOE-IN AND TOE-OUT SETTINGS
Steering Rod
Toe-In--------Positive
Toe-Out-----Negative
Example:
ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN
Brake is not on
Engine at idle
( Neutral Position )
Brake is on
Brake Adjust Nut
( Braking Position )
Brake is not on
Engine at full throttle
( Full Throttle Position )Less Brake
More Brake
TightenLoose
* Tighten or loose the adjuster nut will change the brake.
IMPORTANT NOTICE
YOU MUST CHECK THE FOLLOWING BEFORE STARTING
1) RADIO SWITCH SETTINGS - DOES THROTTLE OPEN &
CLOSE? DOES FULL BRAKE APPLY? DOES STEERING
OPERATE IN THE RIGHT DIRECTION? IF NOT, CHECK
RADIO SETUP SWITCHES.
2) TRUCK THROTTLE AND BRAKE LINKAGE - DOES
LINKAGE PULL AND PUSH CORRECTLY WITH RADIO
CONTROLS, SPECIAL FOR BRAKING AND THROTTLE
CLOSING.
3) FAIL SAFE SETTING AND OPERATION - DOES FAIL
SAFE SET FULL BRAKE WHEN RADIO IS OFF? DOES FAIL
SAFE SET BRAKE WHEN BATTERY LED SHOWS RED? IF
NOT, READ AND RESET FAIL SAFE. YOU CAN NOT SET
FAIL SAFE IF RADIO IS NOT CORRECTLY SETUP FIRST.
DO NOT START OR RUN THIS KIT UNTIL YOU CONFIRM
THESE FUNCTIONS, OTHERWISE SERIOUS DAMAGE
WILL OCCUR.