tire removal and installation instruction using a manual ... and dismounting m… · bitte decken...
TRANSCRIPT
Bitte decken Sie die schraffierte Fläche mit einem Bild ab.
Please cover the shaded area with a picture.
(24,4 x 11,0 cm)
Tire removal and installation instruction using a manual tire changer.
I B&S TIS
Version 1.5
Public
Contents
Tire mounting with manual tire changer 1
Tire dismounting with manual tire changer 2
2 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Position the sensor opposite to the
mounting head
Don’t position the sensor at other location
because it may be hit by the tire
1. Fix the rim in the tire changer
180°
Sensor
Sensor
Mounting head
Mounting head
3 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
If the tire slides the correct sensor position is
lost and the tire can hit the sensor
2. Mount the lower bead
Mount the lower bead making sure that the
tire does not slide
Example marking to
indicate the sensor
position before
mounting
Example marking to
indicate the sensor
position before
mounting
At the end of the
mounting the marking
and the sensor position
match => No sliding of
the tire occurred
At the end of the
mounting the marking
and the sensor position
don’t match => Sliding
of the tire occurred
Sensor
Sensor Sensor
Sensor
Mounting head
Mounting head
Mounting head Mounting head
4 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Don’t position the sensor at any other
location because it may be hit by the tire
3. Position the sensor for the upper bead mounting
Position the sensor opposite to the
mounting head
180°
Sensor
Sensor
Mounting head
Mounting head
5 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
If the tire slides the correct sensor position is
lost and the tire may hit the sensor
4. Mount the upper bead
Mount the upper bead making sure that the
tire does not slide
Example marking to
indicate the sensor
position before
mounting
At the end of the
mounting the marking
and the valve match =>
No sliding of the tire
occurred
At the end of the
mounting the marking
and the valve don’t
match => Sliding of the
tire occurred
Example marking to
indicate the sensor
position before
mounting
Sensor
Sensor
Sensor
Sensor
Mounting head Mounting head
Mounting head Mounting head
6 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Contents
Tire mounting with manual tire changer 1
Tire dismounting with manual tire changer 2
7 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Don’t position the bead breaker at the sensor
position as it may be damaged
1. Break the bead on the front side
Position the bead breaker on the opposite
side of the sensor
Sensor Sensor
8 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Position the bead breaker on the opposite
side of the sensor
Don’t position the bead breaker at the sensor
position as it may be damaged
2. Break the bead on the rear side
Sensor Sensor
9 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Don’t position the sensor at any other
location because it may be hit by the tire
3. Fix the wheel in the tire changer
Position the sensor under the mounting
head
Sensor
Sensor
Mounting head Mounting head
10 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
4. Insert the mounting lever
Insert the mounting lever without touching
the sensor
11 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
5. Dismount the upper bead
Dismount the upper bead
12 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
Don’t position the sensor at any other
location because it may be hit by the tire
6. Position the sensor for the lower bead dismounting
Position the sensor under the mounting
head
Mounting head Mounting head
Sensor
Sensor
13 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
If the sensor is not under the mounting head
it can be caught by the tire
7. Insert the mounting lever
Insert the mounting lever only if the sensor
is under the mounting head
View from the rear-bottom
of the mounting machine.
As the sensor is at the
right position (under the
mounting head) it is not
touched by the tire.
View from the rear-bottom
of the mounting machine.
As the sensor is not at
the right position (under
the mounting head) it is
caught by the tire.
Mounting head
Mounting head
Mounting head
Mounting head
Sensor
Sensor
Sensor Sensor
14 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
Public
8. Dismount the lower bead
Dismount the lower bead
15 © Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D