tillage & seeding tools - ag world equipment | farm...

FORGED TO PERFORM.

PRODUCT CATALOGUE 2014

TILLAGE & SEEDING TOOLS

TABLE OF CONTENTS

PRODUCT PAGE043-PWV-0800 70043-PWV-1000 70043-PWV-1200 70043-PWV-1400 70043-PWV-1600 70043-PWV-1800 70047-ACC-1001 73047-ACC-1002 73047-ASY-1000 18047-ASY-1000P 18047-KNH-1000 18047-PWV-0400 70047-PWV-0900 70047-PWV-1000 70047-PWV-1100 70047-PWV-1200 70047-PWV-1300 70047-VRT-1040 20050-KNH-0812 18050-KNH-0820 58050-PWV-0600 70050-PWV-0800 70050-PWV-1000 70050-PWV-1200 70050-PWV-1400 70050-PWV-1600 70050-PWV-1800 70070-RCH-0451 71070-RCH-0452 71070-RSP-0200A 71070-RSP-0210A 71070-RSP-0220A 71100-DRV-1010 72100-DRV-1020 72100-HAM-4000 73100-WDG-0700 72200-ASY-7511P 19200-BNC-3100 17, 32200-DRV-1012 72200-DRV-1013 72200-DRV-1030 72200-GFO-0308 67200-HOE-1700 23200-KNF-0810 22200-KNF-0811 22200-KNF-0813 22200-KNF-0863 32200-KNF-7510 19200-KNF-7511 19200-KNF-7512 19200-KNF-7520 58200-KNF-7521 58

Company Profile 4 – 5

Performance Guarantee 6

Warranty 7

Speed-Loc™ Adapters 8 –13

Replaceable Tips 16 –17

Seeding Single-Shoot 18 – 23

Seeding Multi-Shoot 24 – 51

C-Shank 28 – 33

Edge-On 34 – 39

Drill Specific 40 – 51

Seed Boots 52 – 55

Fertilizer Knives 56 – 63

Tillage (Sweeps & Spikes) 64 –71

Accessories 72 –73

Reference 74 – 83

Product Depth Chart 74

Speed-Loc™ Replacement Parts 75

Speed-Loc™ Adapter Chart 76 –77

Bolt Length Chart 78 – 80

Fastener Chart 81

Dealer List 82 – 83

Contact us 84

PRODUCT PAGE200-KNF-7524 58200-KNF-7525 58200-KNF-7542 20200-KNH-4000 23200-KNH-4010 19200-KNH-4020 58200-KNH-7501 21200-PWV-0400 66200-PWV-0405 67200-PWV-0428 67200-PWV-0528 67200-PWV-0500 66200-PWV-0508 66200-PWV-0700 66200-PWV-0708 66200-PWV-0738 67200-PWV-0900 66200-PWV-0908 66200-PWV-0928 67200-PWV-1000 66200-PWV-1008 66200-PWV-1100 66200-PWV-1108 66200-PWV-1200 66200-PWV-1208 66200-PWV-1300 66200-PWV-1308 66200-PWV-1400 66200-PWV-1408 66200-PWV-1608 66200-PWV-1808 66200-QAS-4711 72200-QAS-4712 72200-QCA-4700 10200-QCA-4710 10200-QCA-5000 10200-QCA-5010 11200-QCA-5020 11200-QCA-5030 11200-REL-1010 73200-SLC-1001 75200-SLC-1010 75200-SLC-1020 75200-SLC-1030 75200-SLC-1035 75200-SLC-1037 75200-SLC-1038 75200-SLC-1039 75200-SPK-0200 67200-SPK-0215 67200-SPK-0230 67200-SPN-0200 23

PRODUCT

PRODUCT PAGE200-SPN-0208 23200-SPN-0300 23200-SPN-0308 23200-TIP-0511 16200-TIP-0800 16200-TIP-0801 16200-TIP-1011 16200-TIP-2011 16200-TIP-3000 16200-TIP-3001 17200-TIP-3011 17200-TIP-4011 17200-VRT-1040 20200-WDG-0206 72200-WDG-0506 72200-WDG-1000 72200-WDG-1006 72300-ATM-1000 54300-ATM-1006 54300-ATM-1010 54300-ATM-1020 54300-ATM-1031 55300-ATM-1035 55300-ATM-1036 55300-BNC-4414 55300-BSH-1200 73300-BSH-1205 73300-HLD-4700 54300-HLD-4710 54300-HLD-5000 54300-HLD-5010 54300-SDS-4755 55300-SQR-1500 55300-SQR-1505 55400-DRV-1000 73400-DRV-1010 73400-WDG-0300 72400-WDG-0700 72410-KNF-0800 22410-KNF-0801 22410-KNF-0824 59410-KNF-0825 59410-KNF-0830 59410-KNF-7551 60410-PWV-0400 68410-PWV-0418 69410-PWV-0518 69410-PWV-0600 68410-PWV-0608 68410-PWV-0800 68410-PWV-0808 68410-PWV-1000 68

PRODUCT PAGE410-PWV-1008 68410-PWV-1200 68410-PWV-1208 68410-PWV-1400 68410-PWV-1408 68410-PWV-1600 68410-PWV-1608 68410-PWV-1800 68410-PWV-1808 68410-QCA-5000 12410-QCA-5010 12410-QCA-5020 13410-QCA-5050 13410-SLC-1001 75410-SLC-1022 75410-SLC-1030 75410-SPK-0200 69410-SPN-0300 23410-SPN-0308 23410-VRT-1000 22599-KNH-7540 21, 60600-BNC-5000 61600-HHA-0750 61600-KNH-7520 59600-KNH-7530 59600-KNH-7540 21, 60600-KNH-7552 60600-KNH-7562 32600-TIP-7500 61600-TIP-7501 61600-TIP-7507 61610-ASY-4020 30610-ASY-4026 30612-ASY-0711 31612-ASY-0712 31612-ASY-0711L 31612-ASY-0712L 32612-ASY-0711P 31612-ASY-0712P 31612-ASY-0711LP 31612-ASY-0712LP 31620-ASY-5010 33620-ASY-5015 33620-ASY-5020 33620-ASY-5020M 33628-ASY-5010 39628-ASY-5015 39628-ASY-5020 39628-ASY-5020M 39650-ASY-1000G 51650-ASY-1000L 51650-ASY-1000N 51

PRODUCT PAGE675-ASY-1801GM 62675-ASY-1801GN 62680-ACC-0001 36, 73680-ACC-0002 36680-ACC-0003 36680-ACC-1000 73680-ASY-1000 18680-ASY-1000P 18680-ASY-4020 36680-ASY-4026 36682-ASY-0711 37682-ASY-0712 37682-ASY-0711L 37682-ASY-0712L 37682-ASY-0711P 37682-ASY-0712P 37682-ASY-0711LP 37682-ASY-0712LP 37682-ASY-2063 38682-ASY-2064 38682-ASY-2063P 38682-ASY-2064P 38682-ASY-2063M 38682-ASY-2064M 38682-ASY-2063MP 38682-ASY-2064MP 38683-ASY-4020G 42683-ASY-4020L 42683-ASY-0711G 43683-ASY-0712G 43683-ASY-0711L 43683-ASY-0712L 43683-ASY-0711LP 43683-ASY-0712LP 43683-ASY-0711GP 43683-ASY-0712GP 43683-ASY-1000P 42683-KNH-1000 42684-ASY-4020G 48684-ASY-4020L 48684-ASY-0711G 49684-ASY-0712G 49684-ASY-0711L 49684-ASY-0712L 49684-ASY-0711LP 49684-ASY-0712LP 49684-ASY-0711GP 49684-ASY-0712GP 49684-ASY-1000P 48684-KNH-1000 48685-ASY-1801G 62685-ASY-1801GM 62

PRODUCT PAGE685-ASY-1801GN 62685-ASY-1801L 62685-ASY-1801M 62685-ASY-1801N 62686-ASY-0711G 50686-ASY-0712G 50686-ASY-0711L 50686-ASY-0712L 50686-ASY-0711LP 50686-ASY-0712LP 50686-ASY-0711GP 50686-ASY-0712GP 50693-ASY-4020G 44693-ASY-4020L 44693-ASY-0711G 45693-ASY-0712G 45693-ASY-0711L 45693-ASY-0712L 45693-ASY-0711LP 45693-ASY-0712LP 45693-ASY-0711GP 45693-ASY-0712GP 45693-ASY-1000P 44693-KNH-1000 44694-ASY-4020G 46694-ASY-4020L 46694-ASY-0711G 47694-ASY-0712G 47694-ASY-0711L 47694-ASY-0712L 47694-ASY-0711LP 47694-ASY-0712LP 47694-ASY-0711GP 47694-ASY-0712GP 47694-ASY-1000P 46694-KNH-1000 46880-ASY-1000 73880-BSH-1130 73880-BSH-1150 73880-CPL-2500 73880-HCL-0001 73880-HCL-0002 73880-ORF-0001 73880-WDG-0300 72880-WDG-0301 72

QUICK REFERENCE GUIDE

THE SEED PLACEMENT YOU TRUST

tillagetools.com

Customers have come to trust Bourgault Tillage Tools to deliver industry-leading seed placement for over 15 years.

Not actual seed placement

BOURGAULTT I L L A G E T O O L S

Now that trust can be placed in our Advantage Series line of multi-shoot openers.

No matter what make of machine you pull in the field, choose from Bourgault Tillage Tools’ line of multi-shoot Advantage Series openers for any seeding application.

JUST GOT BETTER

tillagetools.com

We manufacture a broad range of ground-engaging tools for tillage, seeding and fertilizing. Our products fit most North American manufactured tillage and air seeding machines, as well as some European and Australian made equipment. See the application chart at the back of this catalogue for a list of the broad range of equipment we fit. Our line includes bolt-on products, as well as our patented Speed-Loc™ quick change system.

We understand the diversity of farming methods and we endeavor to build products to meet those needs. We believe that by listening to our customers and understanding their needs, we will continue to develop products that help our farming customers compete in this ever-challenging agricultural economy.

We respect and value the relationship we have with all whom we do business including our customers, dealers, distributors and suppliers. We strive to provide products that are of excellent value and high quality, and back this by our “Performance Guarantee.” We endeavor to provide sales and service people that are helpful and knowledgeable and to provide “Gold Standard” service and support.

We believe our employees are our most important asset. We encourage a work environment of mutual respect, regardless of one’s job or title. We believe in compensation systems that pay fair and competitive wages, while also rewarding extra efforts. Our Productivity Bonus system in our production areas rewards steady and consistent effort, and helps to keep production costs

down. Our company-wide Profit Share plan encourages all of our employees to work towards common goals. We encourage continued skills and personal development to help our people reach their goals, and in turn the company benefits from a higher skilled workforce.

Being a responsible corporate citizen is very important to us at Bourgault Tillage Tools. We believe that everyone has a responsibility to help build a world that is sustainable, and we endeavor to operate our business in that way. One example of this is our participation in the “green power” program offered by our electrical supplier. Our plan is to continue increasing the purchase of cleaner source energy in order to help clean up our air and environment. We are also moving to cleaner production processes within our plant to ensure minimum pollution to the environment. In tune with our principles of sustainability, we support agricultural practices that will leave the land and the environment healthy and intact for future generations.

As we expand globally, we are excited by the challenge to supply our tillage and seeding tools to agricultural markets around the world, and at the same time remain committed to maintaining a strong connection with our domestic and local markets. By understanding “the company behind the product and the principles behind the company,” we hope that you will be comfortable in dealing with us now and into the future.

Sincerely,

Board of Directors and All Company AssociatesF. P. Bourgault Tillage Tools Ltd.

The Company behind the Product,The Principles behind the Company.


Leadership through ExperienceWe do our best to lead and manage our company based on a clear vision, mission, core values and principles. We agree on the direction that we choose to travel to create a brighter future for our business and a healthier, happier and more prosperous future for our farm customers, dealers, distributors, suppliers and as well as for our company associates.

More than 25 years ago, from our own expertise in tillage and seeding equipment and from our own farming and hands-on field experience, we realized that any tillage or seeding unit was only as good as the tillage and seeding tool openers being used on that machine. In the early and mid 1980s, we recognized the serious problems and limitations with the existing tillage and seeding tool openers. We realized that leadership and innovation was sorely lacking in the research and development of tillage and seeding tools.

Beginning with the innovations of the parallel wing sweep and the quick change knife tips, for more than 25 years Bourgault Tillage Tools has been providing leadership and innovations in the tillage and seeding tools industry. Today, we continue to innovate in order to provide you, our farm customer, with the most innovative and highest quality tillage and seeding tools, and we look forward to continue serving you into the future.

Joseph L. BourgaultPresident

PERFORMANCEGUARANTEE

tillagetools.com

Bourgault Tillage Tools guarantees the product you purchase will perform to its designed specification under normal conditions.

If the product does not perform its designed task within the first season of use, please inform us of the issue immediately and grant us the opportunity to visit your field to assess the situation. If we cannot rectify the situation, we will guarantee you a 100% refund.

Trip Strength ConsiderationsAt Bourgault Tillage Tools, we build products that last. Our seed openers need to perform in some challenging conditions, and we design our products with durability in mind. The end user has the responsibility to make sure the machine is best suited to the operating conditions. Trip strength is an important consideration. When it comes to trips, heavier is not necessarily better! Buying a seeding machine with heavier trips than required for proper penetration may result in:

• Broken or damaged seed openers• Broken or bent shanks • More rocks being pulled to the surface

Proper trip strength will save you time and money. When determining the appropriate trip strength, some factors to consider are: soil type, amount of rock and type of seed opener used. Some people believe a heavy trip is a “one size fits all” scenario. This is simply not true. Take the time and make sure you get a machine with appropriate trip strength for your farming operation.

Bourgault Tillage Tools reserves the right to limit warranty claims on trip strengths greater than 400 pounds.

Warranty is limited to the replacement of the failed part and does not cover any consequential damages. To obtain warranty, the part must be returned to the dealer. The dealer will complete the Warranty Claim Form.

All products are warranted from the date of purchase as follows:

• 1st year prorated to a maximum of 100%• 2nd year prorated to a maximum of 70%• 3rd year prorated to a maximum of 40%

Carbide is warranted for loss only. Chipping of carbide is normal. If the brazing fails and the carbide falls off, return the part to the dealer.

WARRANTYTERMS

BOURGAULTT I L L A G E T O O L SBOURGAULTT I L L A G E T O O L S

SPEED-LOC™

The Speed-Loc™ system provides more benefits than any other system!

Consistent depth control: The upper stop on the Speed-Loc™ adapters ensures that your tillage or seeding tools are always running at the same depth.

Peace of mind: The spring-loaded locking pin ensures that the tools will stay securely in place in all conditions, and we back that up with a 100% guarantee.

Years of trouble-free operation: The Speed-Loc™ adapters are designed with durability in mind. The cast adapters are heat-treated for increased strength and wear resistance.

tillagetools.com

10

47°• Fits all Bourgault and

Ezee-On field cultivators, air seeders and air drills.

• 1-3/4" (45 mm) centre to centre.

• 1/2" (12 mm) hex head bolts.

47°• Fits field cultivators

with 47° shanks, except Bourgault and Ezee-On.


• Oversize head plow bolts.

50°• Fits Bourgault and Morris

Concept 2000.

• Not recommended for primary tillage use, only for seeding.



200 SERIESQUICK CHANGE ADAPTERS

200-QCA-4700 200-QCA-4710 200-QCA-5000

Speed-Loc™ Rebate

Bring any 100 Series or competitor’s adapters in to your local dealer and receive a $7 cash rebate when you purchase a set of 200 Series adapters. For a limited time only.


11

50°• Fits air drills with

50° shanks.

• Not recommended for heavy deep tillage.


• 1/2" (12 mm) plow bolts.

• Can also be used on a 43° shank with the addition of a 7° wedge (100-WDG-0700).

50°• Fits European built tillage

and seeding implements.

• 63 mm to 80 mm centre to centre.

• M12-DIN608 10.9 plow bolts.

50°• Fits Horsch shanks.

• 57 mm centre to centre.


SPEED-LOC ///

200-QCA-5010 200-QCA-5020 200-QCA-5030

Not sure which adapter is for you or which bolts you need?

Refer to our Speed-Loc™ adapter chart on pages 76–77. For a complete list of bolt lengths, see pages 78–80.

For Speed-Loc™ adapter replacement parts, refer to page 75.

tillagetools.com

12

50°• Fits Bourgault and Morris Magnum chisel

plows, and Morris Concept 2000 with the LH755 shank.



50°• Fits all 50° chisel plows except the Bourgault

and Morris units identified for use with the 410-QCA-5000.

• 1-3/4" to 3" (45 mm to 77 mm) centre to centre.


410 SERIESQUICK CHANGE ADAPTERS

410-QCA-5000 410-QCA-5010

On a Bourgault four-hole shank, the centre hole of the adapter should be plugged to protect the spring ball from NH3 gases when used as a NH3 applicator.

In rocky or abrasive conditions, the bottom nut may experience excessive wear or damage. This problem is alleviated by placing the bottom bolt in from the back of the shank and putting the nut in the front of the adapter.

This adapter can be used on a 43° shank by adding a 7° plastic wedge (400-WDG-0700).

Special note for John Deere: certain chisel plow models including the 685, 1810, 1820 and 2400 may need a 3° wedge to attain proper sweep pitch. See pages 72–73 for more information.

Shanks with the open bottom bolt hole require the 047-ACC-1002 to keep the bottom bolt in place.


13

50°• Fits Kverneland

(CLD Grubber) shanks.



50°• Fits Lemken shanks.



SPEED-LOC ///

410-QCA-5020 410-QCA-5050

Not sure which adapter is for you or which bolts you need?

Refer to our Speed-Loc™ adapter chart on pages 76–77. For a complete list of bolt lengths, see pages 78–80.

Speed-Loc™ Rebate

Bring any 400 Series or competitor’s adapters in to your local dealer and receive a $7 cash rebate when you purchase a set of 410 Series adapters. For a limited time only.

For Speed-Loc™ adapter replacement parts, refer to page 75.

SINGLE-SHOOT OPENERSBourgault Tillage Tools has been providing producers all around the world with industry-leading quality and innovation in single-shoot seeding technology. You can trust in the quality that our products stand for.

200 Series Speed-Loc™


Edge-On Shank

47° C-Shank

47° and 50° C-Shank

tillagetools.com

16 REPLACEMENT TIPSLONG-WEARING HIGH-CHROME TIPS

200-TIP-2011200-TIP-1011

200-TIP-0801

Carbide Tip1/2" (12.7 mm) with carbide insert on the nose

Chrome Spread Tip3" (76 mm)

Vertical Tip1" (25 mm) with double carbide insert

Chrome Tip3/4" (19 mm)

Carbide Tip3/4" (19 mm) with carbide insert on the nose

Spread Tip2" (50 mm) with carbide insert on the nose and underside of the wings

200-TIP-0511

200-TIP-3000

200-TIP-0800


17SINGLE-SHOOT SEEDING ///

200-TIP-3011 200-TIP-4011200-TIP-3001


Spread Tip3" (76 mm) with carbide insert on the nose and hard facing on the underside of the wings


All tips on these pages (except 200-TIP-0511) are compatible with Flexi-Coil Stealth openers.

200-NUT-3101

200-BLT-3102

200-BNC-3100

Bolt and Nut ComboThis bolt and nut combination is used to secure Category 1 tips, Titan 1/2" tips and Advantage Series tips. It is important not to over tighten the bolt when installing the tips. The bolt has a strip of lock-tight applied to the threads, so it needs only to be turned in by hand until the shoulder of the bolt makes contact with the nut.

Over torquing with a power drill will result in difficulty when removing. Recommended to torque to 84 in/lbs or 7 ft/lbs.

tillagetools.com

18

Fits 47° and 50° C-Shank• Seed is delivered through the precision funnel opening.

• Front delivery provides precise seed delivery and reduces plugging with better soil flow.

• Can be used with any of the replaceable tips (sold separately) allowing you to choose the tip for your conditions.

• Extra hard surfacing on critical wear areas to increase the life of the holder.

• Also available with a phosphorous tube add-on (047-ASY-1000P).

• When installing on a Bourgault with MRBs, use 047-KNH-1000 directly behind the MRBs.

Fits Edge-On Shank• Seed is delivered through the precision funnel opening.

• Front delivery provides precise seed delivery and reduces plugging with better soil flow.


• Reinforced holder reduces breakage in rocky conditions.


• Also available with a phosphorous tube add-on (680-ASY-1000P).

Fits 47° and 50° C-Shank• Can be used with any of the replaceable tips (sold separately) allowing you

to choose the tip for your conditions.

• Rear delivery provides additional trash clearance.

• Slotted bolt holes provide the ability to fit many different makes and models.

SINGLE-SHOOT OPENERS

047-ASY-1000 047-KNH-1000

680-ASY-1000 680-ASY-1000P

050-KNH-0812



Fits 200 Series Speed-Loc™• Can be used with any of the replaceable tips (sold separately) allowing you

to choose the tip for your conditions.

• Works with Bourgault or Flexi-Coil square tube seed boot.

• Rear delivery provides additional trash clearance.

Fits 200 Series Speed-Loc™• Precise seed placement due to the funnel being close to the tip and to the

bottom of the furrow.

• Reinforced funnel with hard surfacing for longer wear life.

• Funnel fits Bourgault and Flexi-Coil square tube seed boots.

• Choose between 3/4" weld-on carbide or non-carbide tips.

• The carbide opener is also available with a phosphorous tube add-on (200-ASY-7511P).

Fits 200 Series Speed-Loc™• Excellent plug resistance due to step located behind the tip.

• The funnel is reinforced with hard surfacing for longer wear life.

• Funnel fits Bourgault and Flexi-Coil square tube seed boots.

• 3/4" weld-on carbide tip for prolonged tip life and better soil penetration.

200-KNH-4010

200-KNF-7511200-KNF-7510

200-KNF-7512

200-KNF-7511P

tillagetools.com

20 SINGLE-SHOOT OPENERS

Fits 200 Series Speed-Loc™• Perfect for heavy gumbo soils, extra space between the tip and the tube

reduces plugging.

• High-chrome tip is long-lasting and provides great penetration.

• High-value opener when you are seeding into low abrasive soils or heavy gumbo.

Fits 200 Series Speed-Loc™• 1" weld-on tip with extra carbide for long-lasting wear life.

• Fits any 200 Series Speed-Loc™ adapter.

• Vertical approach reduces rock pulling and soil throw.

Fits 47° C-Shank• 1" weld-on tip with extra carbide for long-lasting wear life.


• Vertical approach reduces rock pulling and soil throw.

• Fits 1-3/4" bolt hole spacing.

200-KNF-7542

200-VRT-1040

047-VRT-1040



Fits 47° and 50° C-Shank• Choose between long-wearing carbide or chrome tip.

• The larger tip provides extra long wear and decreases wear on the holder.

• Slotted bolt hole spacing give this opener flexibility.

• Fits 1-3/4" or 2-1/2" bolt hole spacing.

Fits 47° C-Shank• This opener is the same as above except that it is designed to have a better

fit on the Bourgault shank.

Fits 200 Series Speed-Loc™• This opener is used in conjunction with the Technotill system.


• The high-chrome tip with a carbide insert provides additional wear life.

600-KNH-7540

599-KNH-7540

200-KNH-7501

For replacement tip options, see page 61.

For replacement tip options, see page 61.

tillagetools.com

22 SINGLE-SHOOT OPENERS

Fits 200 Series Speed-Loc™• Use in conjunction with the 300 Series Seed Boot System on pages 54 and 55.

Designed to work with the 300-ATM-1035.

• 3/4" weld-on tip, comes with or without carbide.


• This low disturbance opener is low in draft and easy pulling.



• 3/4" weld-on tip with extra carbide for long-lasting wear life.


• Vertical approach reduces rock pulling.



• 3/4" weld-on tip, comes with or without carbide.


• This low disturbance opener is low draft and easy pulling.



• 1" weld-on tip with extra carbide for long-lasting wear life.


• Vertical approach reduces rock pulling.

200-KNF-0811 200-KNF-0810

200-KNF-0813

410-KNF-0801 410-KNF-0800

410-VRT-1000






• Our extensive tip options allow you to choose the tip that is right for you.


Fits 200 Series Speed-Loc™• Provides 1-1/2" to 1-3/4" seed spread. Works best with a 1" single tube seed boot.

• Long-wearing high-chrome tip.

• Runs through the ground at a fairly vertical angle for less rock pulling.

• Very dependable in many different conditions.

Fits 200 Series Speed-Loc™• 2" spread (200-SPN-0200 or 200-SPN-0208) or 3" spread (200-SPN-0300 or

200-SPN-0308).

• A larger spread allows for nitrogen fertilizer to be placed with the seed.

• Choose from 1/4" (200-SPN-0200 or 200-SPN-0300) material or 5/16" (200-SPN-0208 or 200-SPN-0308) for increased wear life.

• Designed to fit any 200 Series adapter.

Fits 410 Series Speed-Loc™• 3" spread (410-SPN-0300 or 410-SPN-0308).

• A larger spread allows for nitrogen fertilizer to be placed with the seed.

• Choose from 1/4" (410-SPN-0300) material or 5/16" (410-SPN-0308) for increased wear life.

• Designed to fit any 410 Series adapter.

200-KNH-4000

200-HOE-1700

410-SPN-0300 410-SPN-0308

200-SPN-0200 200-SPN-0208 200-SPN-0300 200-SPN-0308

MULTI-SHOOT OPENERSThe quality and seed placement you trust now comes with a dose of fertilizer. Choose from our extensive line of bolt-on and Speed-Loc™ openers for any seeding application.

Edge-On Drill SpecificC-Shank

26

tillagetools.com

With the development and increased use of multi-shoot knives for one-pass seed and fertilizer placement, the following question is often asked:

“How much fertilizer can I place with the seed without causing germination problems or seedling damage?”

The answer to this question is very complex.

Precautions and Risk Factors*Consider these factors when using any products between pages 30 to 51.

FERTILIZER SOURCE – depending on the type of fertilizer used, damage can occur either through ammonia toxicity or salt effects or a combination of both as in the case with blended fertilizer.

FERTILIZER RATES – typically, the risk of crop seedling injury increases with higher rates of fertilizer.

CROP TYPE – crops vary in their ability to tolerate seed-placed fertilizer, with cereals being able to withstand more than oilseeds and pulses falling somewhere in between.

SEED QUALITY – with everything else equal, seed with poor vigor will suffer more damage from seed-placed fertilizer than seeds with high vigor. If seed vigor is questionable, have it tested.

SOIL MOISTURE – with soil at or near saturation point, the toxic effects of fertilizer are diluted so seeds can germinate and develop with few problems. If conditions are very dry, reduce the amount of fertilizer placed near the seed.

SOIL TEXTURE – fine textured soils such as clay or clay loam tend to also reduce these toxic effects over coarse or sandy soils because of their ability to hold more water and absorb toxic free ammonia.

ORGANIC MATTER – higher levels of organic matter (OM) in a soil also lessen the risk of damage. For example, reduced levels of OM on dry, eroded hilltops seedlings are more prone to injury.

SEEDBED UTILIZATION – or SBU is the proportion of the seedbed used for seed and fertilizer placement. Ex: 2" openers on 10" row spacing have a SBU of 20%. As SBU increases, the crops tolerance to higher rates of seed-placed fertilizer increases.

SEEDING DEPTH, PACKING AND SPEED – these points are also factors to take into consideration as they may compromise seed and fertilizer placement as well as the overall quality of the seeding operation.

ADVERSE SEEDING CONDITIONS – excessively wet or dry soil at time of seeding can cause erratic seed placement, poor seed-to-soil contact and poor separation, which will also affect the amounts of seed placed fertilizer you can apply.

If any of the above conditions are less than ideal, it is advisable to reduce your fertilizer rate accordingly.

!

MULTI-SHOOT OPENERS

*It is our company’s policy not to recommend or endorse specific “safe” rates of fertilizer for multi-shoot openers due to the wide variance in the PRECAUTIONS AND RISK FACTORS listed above. Most of our knives are tested at independent research facilities to verify only the placement of seed and fertilizer. We suggest that producers consult their local agronomist to establish acceptable fertilizer rates for their unique seeding conditions.

27


Tip Styles

Single-Shoot

The seed is placed directly behind the tip in the middle of the row. For single-shoot seeding, choose from a variety of tips on pages 16 and 17.

Side Band

The seed is placed directly behind the tip in the middle of the row. Fertilizer is placed in a band to the side and behind the wing.

Side Band (Triple-Shoot)

The seed is placed directly behind the tip in the middle of the row. Fertilizer is placed in a band to the side and behind the wing. Liquid phosphorous is added to the seed row.

Paired Row

The seed is delivered in two distinct rows while the fertilizer is placed in the centre.

Fertilizer Types

Granular

Liquid

NH3

Maxquip NH3

Liquid Phosphorous

SYMBOL LEGEND

C-SHANK

tillagetools.com

C-SHANK


Side Band

Granular* 612-ASY-0711/0712 31

Liquid* 612-ASY-0711L/0712L 31

*Also available with ¼" O.D. liquid phosphorous tube

Side Band

Liquid 600-KNH-7562 32Liquid 200-KNF-0863 32

Single Row

Granular 620-ASY-5015 33

Paired Row


Liquid 610-ASY-4026 30

Paired Row


NH3 620-ASY-5020 33

NH3 Maxquip 620-ASY-5020M 33

Advantage Series Horizontal Seed / Fertilizer Separation

Liquid Openers Horizontal Seed / Fertilizer Separation

Titan Series Horizontal & Vertical Seed / Fertilizer Separation

FIND YOUR OPENER

30

tillagetools.com

Double-Shoot LiquidFits 47° and 50° C-Shank

Double-Shoot GranularFits 47° and 50° C-Shank

PAIRED ROW

ADVANTAGE SERIESHORIZONTAL SEED / FERTILIZER SEPARATION

610-ASY-4020 610-ASY-4026

• Fertilizer is placed down the middle of the row and on the same plane as the seed. The seed is placed in two distinct rows measuring 3" centre to centre.

• The 4" Paired Row tip allows you to achieve great seedbed utilization.

• Extended wear life due to high-chrome tip with carbide inserts on the nose and underside.

• Carbide placement provides sharp cutting edges for excellent penetration.

• Hard facing is placed on critical wear points to ensure a long-lasting holder.

• Replaceable tip to ensure high-wear points can be replaced at a lower cost.

• Tests have shown our Paired Row Advantage to be the industry leader in low draft and soil disturbance.

• The sleek holder design combined with the front delivery concept reduces plugging and encourages trash clearance.

31


Double-Shoot GranularFits 47° and 50° C-Shank

• Triple-Shoot Liquid Phosphorus Openers: 612-ASY-0711P, 612-ASY-0712P

SIDE BAND

MULTI-SHOOT /// C-SHANK ///

612-ASY-0711 (left) 612-ASY-0712 (right)


• Quick change liquid insert provides easy switching from granular to liquid.

• Triple-Shoot Liquid Phosphorus Openers: 612-ASY-0711LP, 612-ASY-0712LP

612-ASY-0711L (left) 612-ASY-0712L (right)

• The 2-1/4" Side Band tip provides you with the lowest draft and soil disturbance in the industry while ensuring great seed placement.

• Long-wearing carbide-enforced chrome tip is reinforced where you need it – on the nose and wing.


• Hard facing is placed on critical wear points to ensure a long-lasting holder, proper seed placement and virtually no plugging.


• The streamlined holder design combined with the front delivery concept reduces plugging and encourages trash clearance.

Optional P Tube

32

tillagetools.com

Double-Shoot LiquidFits 200 Series Speed-Loc™ Adapters

• This is the only Speed-Loc™ multi-shoot opener that we carry. It provides all the benefits of the Speed-Loc™ system with the seed placement that you trust.



LIQUID OPENERSHORIZONTAL SEED / FERTILIZER SEPARATION

SIDE BAND

600-KNH-7562 200-KNF-0863

• These unique side band openers provide good horizontal separation with slight vertical fertilizer separation.

• The high-chrome tip is protected with a carbide insert on the nose and a solid carbide wing.


• The opener works very well when used with a pressurized liquid system.

For replacement tip, see page 61.

600-TIP-7507

33


TITAN SERIESHORIZONTAL & VERTICAL SEED / FERTILIZER SEPARATION

Paired Row GranularFits 47° and 50° C-Shank

Paired Row NH3

Fits 47° and 50° C-Shank

Single Row GranularFits 47° and 50° C-Shank

Paired Row NH3 MaxquipFits 47° and 50° C-Shank

620-ASY-5010

620-ASY-5020 620-ASY-5020M

620-ASY-5015

• The Titan provides true vertical separation between seed and fertilizer. It also provides more centre-to-centre horizontal separation than our Advantage Series openers.

• 1/2" wide fertilizer knife for lower disturbance and more precise fertilizer placement.

• Adjustable front knife allows you to set the depth of the fertilizer from 3/4" to 1-1/2".

• Three strategic carbide locations for additional wear life. Hard facing is placed on key wear points that don’t have carbide.

• The modular design allows for replacement of worn parts instead of the entire opener.

• The Titan has been tested to show superior performance when compared to other paired row openers.

• Adjustable based on seed and fertilizer placement needs.

EDGE-ON

tillagetools.com

Side Band

Granular* 682-ASY-0711/0712 37

Liquid* 682-ASY-0711L/0712L 37

Liquid* 682-ASY-2063/2064 38

Maxquip NH3* 682-ASY-2063M/2064M 38

*Also available with ¼" O.D. liquid phosphorous tube

Single Row


Paired Row


Liquid 680-ASY-4026 36

Paired Row


NH3 628-ASY-5020 39

NH3 Maxquip 628-ASY-5020M 39

EDGE-ON


Advantage Series Horizontal Seed / Fertilizer Separation

Titan Series Horizontal & Vertical Seed / Fertilizer Separation

FIND YOUR OPENER

36

tillagetools.com

Double-Shoot LiquidFits Edge-On Shank, Bourgault PHD (except XTC), Concord,* Morris

Double-Shoot GranularFits Edge-On Shank, Bourgault PHD (except XTC), Concord,* Morris


PAIRED ROWPAIRED ROW

680-ASY-4020 680-ASY-4026

• Fertilizer is placed down the middle of the row and on the same plane as the seed. The seed is placed in two distinct rows measuring 3" centre to centre.




• Order 680-ACC-0003 if installing the 680-ASY-4020 on a Bourgault.



• Tests have shown our Paired Row Advantage to be the industry leader in low draft and soil disturbance.


• Order 680-ACC-0002 if installing the 680-ASY-4026 on a Bourgault.

* Make sure to order 680-ACC-0001 when installing on a Concord (see page 73).

37


Double-Shoot GranularFits Edge-On Shank, Bourgault PHD (except XTC), Concord,* Morris

• Triple-Shoot Liquid Phosphorus Openers: 682-ASY-0711P, 682-ASY-0712P

MULTI-SHOOT /// EDGE-ON ///

SIDE BANDSIDE BAND

682-ASY-0711 (left)682-ASY-0712 (right)

Double-Shoot LiquidFits Edge-On Shank, Bourgault PHD (except XTC), Concord,* Morris



682-ASY-0711L (left)682-ASY-0712L (right)







Optional P Tube

38

tillagetools.com

Double-Shoot LiquidFits Edge-On Shank, Bourgault PHD, Concord,* Morris

Double-Shoot NH3 MaxquipFits Edge-On Shank, Bourgault PHD, Concord,* Morris

• Outfitted with a Maxquip tube that is inserted into the 1/4" stainless steel liquid tube.

Triple-Shoot LiquidFits Edge-On Shank, Bourgault PHD, Concord,* Morris

• Use to add liquid phosphorus to the seed row.

Triple-Shoot NH3 MaxquipFits Edge-On Shank, Bourgault PHD, Concord,* Morris

• Fitted with a 1/4" stainless steel tube that applies liquid phosphorus down the centre of the seed row.


SIDE BAND

682-ASY-2063 (left)682-ASY-2064 (right)

682-ASY-2063M (left)682-ASY-2064M (right)

682-ASY-2063MP (left)682-ASY-2064MP (right)

682-ASY-2063P (left)682-ASY-2064P (right)

• The 2-1/4" Side Band tip provides you with low draft and soil disturbance while ensuring great seed placement.



• The welded liquid tube is protected by the carbide tip and runs along the front of the opener to prevent plugging.


* Make sure to order 680-ACC-0001 when installing on a Concord (see page 73).

39


TITAN SERIESHORIZONTAL & VERTICAL SEED / FERTILIZER SEPARATION

628-ASY-5010 628-ASY-5015

628-ASY-5020 628-ASY-5020M

Paired Row GranularFits Edge-On Shank, Morris

Paired Row NH3

Fits Edge-On Shank, Morris

Single Row GranularFits Edge-On Shank, Morris

• Not recommended for North America.

Paired Row NH3 MaxquipFits Edge-On Shank, Morris

• The Titan provides true vertical separation between seed and fertilizer. It also provides more centre-to-centre horizontal separation than our Advantage Series openers.

• 1/2" wide fertilizer knife for lower disturbance and more precise fertilizer placement.

• Adjustable front knife allows you to set the depth of the fertilizer from 3/4" to 1-1/2".

• Three strategic carbide locations for additional wear life. Hard facing is placed on key wear points that don’t have carbide.

• The modular design allows for replacement of worn parts instead of the entire opener.

• The Titan has been tested to show superior performance when compared to other paired row openers.

DRILL SPECIFIC

tillagetools.com

DRILL SPECIFIC


As the direct seeding industry evolves, unique shank styles are being developed by air drill manufacturers. Bourgault Tillage Tools is dedicated to building openers that fit these new shanks. You can now be assured the quality you have come to trust in our openers will be available on your choice of air drills.

Advantage Series Benefits

• Ultra-Low Draft• Minimal Seedbed Fracturing• Less Soil Disturbance• Carbide on Tip and Wings• Replaceable Tip

• Virtually No Plugging• Smoother Field Finish• Even Germination• Seed and Fertilizer Separation

tillagetools.com

42 MORRIS CONTOUR IADVANTAGE SERIES OPENERS

Double-Shoot Granular• Fertilizer is placed down the middle of the row and on the same plane as the

seed. The seed is placed in two distinct rows measuring 3" centre to centre.







Double-Shoot Liquid• Note: all information from the opener above applies to this product as well.


Single-Shoot• Can be used with any replaceable tip allowing you to choose the tip for your

conditions. (Tips sold separately.)


PAIRED ROW

SINGLE-SHOOT

683-ASY-4020G

683-KNH-1000 683-ASY-1000P

683-ASY-4020L

43


Double-Shoot Liquid• Quick change liquid insert provides easy switching

from granular to liquid.


Double-Shoot Granular• Triple-Shoot Liquid Phosphorus Openers:

683-ASY-0711GP, 683-ASY-0712GP

MULTI-SHOOT /// DRILL SPECIFIC ///

SIDE BAND

683-ASY-0711G (left)683-ASY-0712G (right)



• Long-wearing carbide tip is reinforced where you need it – on the nose and wing.





Optional P Tube

tillagetools.com

44














PAIRED ROW

SINGLE-SHOOT

693-ASY-4020G

693-ASY-4020L

MORRIS CONTOUR IIADVANTAGE SERIES OPENERS

693-KNH-1000 693-ASY-1000P

45






693-ASY-0711GP, 693-ASY-0712GP

SIDE BAND










Optional P Tube

tillagetools.com

46 CASE IH 700, NEW HOLLAND P2060, FLEXI-COIL PH5500ADVANTAGE SERIES OPENERS














PAIRED ROW

SINGLE-SHOOT

694-ASY-4020G

694-ASY-4020L

694-KNH-1000 694-ASY-1000P

47






694-ASY-0711GP, 694-ASY-0712GP

CASE IH 700, NEW HOLLAND P2060, FLEXI-COIL PH5500ADVANTAGE SERIES OPENERS


SIDE BAND









Optional P Tube

tillagetools.com

48 CASE IH 800, NEW HOLLAND P2070, FLEXI-COIL PH5700ADVANTAGE SERIES OPENERS














PAIRED ROW

SINGLE-SHOOT

684-ASY-4020G

684-ASY-4020L

684-KNH-1000 684-ASY-1000P

49






684-ASY-0711GP, 684-ASY-0712GP

CASE IH 800, NEW HOLLAND P2070, FLEXI-COIL PH5700ADVANTAGE SERIES OPENERS


SIDE BAND









Optional P Tube

tillagetools.com

50





686-ASY-0711GP, 686-ASY-0712GP

SEED HAWKADVANTAGE SERIES OPENERS

SIDE BAND









Optional P Tube


51JOHN DEERE CONSERVA PAK™

FERTILIZER OPENER

Liquid Fertilizer NH3 Fertilizer Granular Fertilizer

650-ASY-1000G 650-ASY-1000L 650-ASY-1000N

• These openers replace the current John Deere fertilizer opener on the Conserva Pak™ drill.

• Comes in either granular, liquid or NH3 fertilizer options with quick-remove liquid NH3 tube for flexibility.

• Comes complete with a 3/4" carbide replaceable tip.

• Heat-treated and hard-surface holder for a long-wearing product.

SEED BOOTSThe quick change seed boot system consists of two parts: the seed boot holder which bolts on to the back of the shank and the seed boot attachment which fits into the holder and is secured with a bolt and nut. There are six different interchangeable attachments to choose from, each giving a different seed spread pattern. This system allows you to match your seed spread to the width of opener you are using. It is perfect for producers who want to switch back and forth from a wide seed spread behind a sweep to a narrow seed band behind a knife.

tillagetools.com

54 300 SERIES

300-HLD-4700

300-ATM-1000

300-HLD-4710

300-ATM-1006

300-HLD-5000

300-ATM-1010

300-HLD-5010

300-ATM-1020

SEED BOOT HOLDERS

SEED BOOT ATTACHMENTS

This holder has 1-3/4" (45 mm) bolt hole spacing. The bolt hole section is designed flat to fit the Bourgault and Ezee-On 47° shanks.

This spreader attachment will distribute the seed evenly in a 3" to 4" (76 mm to 100 mm) band. Seed spread may vary depending on sweep size, soil type and fan speed.

This holder has 2-1/4" (57 mm) bolt hole spacing. The bolt hole section is curved to fit any chisel plow shank except the Bourgault and the Morris LH755 shank.

The straight attachment will spread the seed approximately 2-1/2" (63 mm). It works well with the quick change spoons, spikes or any size of sweep.

This holder has 1-3/4" (45 mm) bolt hole spacing. The bolt hole section is curved to fit all 47° shanks except the Bourgault and Ezee-On.

The spreader attachment will distribute the seed evenly in a 6" (152 mm) row. Seed spread may vary depending on sweep size, soil type and fan speed. Works well for organic operations.

This holder has 2-1/4" (57 mm) bolt hole spacing. The bolt hole section is flat and has two sets of holes. The top set of holes should be used in almost all cases when mounting this holder to the shank. It fits on the Bourgault chisel plow shanks as well as the LH755 shank used on the Morris Magnum III and the Morris Concept 2000.

The splitter attachment will place the seed into two distinct rows approximately 6" (150 mm) apart. Seed spread may vary depending on sweep size, soil type and fan speed.


55SEED BOOTS ///

300-ATM-1031 300-ATM-1035 300-ATM-1036 300-BNC-4414

300-BLT-4414

600-NUT-3754

SEED BOOT ATTACHMENTS

This knife attachment will place the seed in a very narrow band. It is designed to be used behind the 200-VRT-1000, 410-VRT-1000, 410-KNF-0800 and 410-KNF-0801.

This bolt and nut secure the quick change seed boot attachments into the holders.

This knife attachment will place the seed in a very narrow band. It is designed to be used behind the 200-KNF-0810, 200-KNF-0811, 200-KNF-0813 and 200-KNH-4000.

This knife attachment will place the seed in a band. There is hard facing on the side and the slot is wider than the 300-ATM-1035. It is designed to be used behind the 200-KNF-0815.

300-SDS-4755300-SQR-1500300-SQR-1505

Square TubeThe square tube seed boot has a slotted top hole to fit 1-3/4" to 2-1/4" (45 to 57 mm) bolt spacing. It accepts 1-1/4" (32 mm) O.D. air hose. The 300-SQR-1500 seed boot is designed to fit curved bottom shanks. The 300-SQR-1505 seed boot is designed to fit flat bottom shanks.

SEED BOOTS

Double-Shoot Paired Row GranularThis double-shoot paired row granular seed boot is designed to maintain seed/fertilizer separation. The fertilizer drops straight down which minimizes “bounce” while the seed is propelled forward and out which minimizes the possibility of seed/fertilizer contact. This product can be used on any C-shank. It has a slotted top hole that allows the boot to fit 1-3/4" to 2-1/4" (45 mm to 57 mm) bolt spacing. This seed boot is designed to use behind sweeps (minimum 7"). It accepts 1-1/4" (31 mm) O.D. hose. It provides a 6" paired row.

FERTILIZER KNIVESWe understand the importance of your fertilizer operation and that you depend on your opener to get it done right. That is why we have designed a full line of fertilizer knives that are durable and stand up to most every condition. Choose from NH3, Granular or Maxquip options.

47° C-Shank

47° and 50° C-Shank



tillagetools.com

58

Fits 47° and 50° C-Shank• Enjoy the flexibility of using any replaceable tip from pages 16 and 17.

(Tips sold separately.)

• The welded tube fits 1/2" (12 mm) cold-flow anhydrous kits.

• Not recommended for rocky areas.

Fits 200 Series Speed-Loc™• Fits on any 200 Series adapter for easy installation and fast replacement.

• Enjoy the flexibility of using any replaceable tip from pages 16 and 17. (Tips sold separately.)

• The welded tube fits 1/2" (12 mm) cold-flow anhydrous kits.

• Not recommended for rocky areas.


• Available with carbide nose (7521) or without (7520). The carbide provides extra wear life and much better penetration.

• The welded tube fits 1/2" (12 mm) (200-KNF-7521 & 7520) cold-flow anhydrous kits or 3/8" (9 mm) (200-KNF-7531 & 7530) hot-gas anhydrous kits.

• Shorter tube length makes this opener better for cultivators and chisel plows.

• Welded tip makes this opener better in rocky conditions.



• The tube fits 1/2" (12 mm) cold-flow anhydrous kits.

• The longer tube length makes this opener better for air seeders and air drills.


FERTILIZER KNIVES

050-KNH-0820

200-KNH-4020

200-KNF-7521 200-KNF-7520

200-KNF-7525 200-KNF-7524


59



• The fertilizer tube fits 1/2" (12 mm) (410-KNF-0825 & 0824) cold-flow anhydrous kits or 3/8" (9 mm) (410-KNF-0830 & 0831) hot-gas anhydrous kits.

• This opener is designed for heavy-duty use.


Fits 47° and 50° C-Shank• This is the most durable opener that we provide for fertilizer placement.

• The tube fits 1/2" (12 mm) cold-flow anhydrous kits.

• Choose from a 3/4" (19 mm) chrome (600-TIP-7500) or carbide (600-TIP-7501) tip. (Tips sold separately.)

• Fits 1-3/4" (44 mm) to 2-1/2" (63 mm) bolt hole spacing. Use on a 43° shank with the addition of a 7° wedge.

Fits 47° and 50° C-Shank• This is the most durable opener that we provide for fertilizer placement.

• The tube fits 3/8" (9 mm) hot-gas anhydrous kits.


• Fits 1-3/4" (44mm) to 2-1/2" (63 mm) bolt hole spacing. Use on a 43° shank with the addition of a 7° wedge.

FERTILIZER KNIVES ///

410-KNF-0825 410-KNF-0824

600-KNH-7520

600-KNH-7530

Not sure which bolts you need?

Refer to our bolt length chart on pages 78–80.

tillagetools.com

60


• The tube fits 1/2" (12 mm) (410-KNF-7551) cold-flow anhydrous kits or 3/8" (9 mm) (410-KNF-07553) hot-gas anhydrous kits. An additional 1-1/4" tube is used for granular fertilizer. This tube also accepts 1-1/8" tube with 880-BSH-1130.

• This opener is designed for heavy-duty use.

• Welded 3/4" (19 mm) tip makes this opener better in rocky conditions.

• Not recommended for seeding.

Fits 47° and 50° C-Shank• The tube fits 1/2" (12 mm) cold-flow anhydrous kits. An additional 1-1/4" tube is used

for granular fertilizer. This tube also accepts 1-1/8" tube with 880-BSH-1130.



• This is the most durable opener that we provide for fertilizer placement.

Fits 47° and 50° C-Shank• Accepts 1-1/4" (31 mm) and 1-1/8" (28 mm) granular hose (with 880-BSH-1130).




Fits 47° C-Shank• Accepts 1-1/4" (31 mm) and 1-1/8" (28 mm) granular hose (with 880-BSH-1130).


• 1-3/4" (45 mm) bolt hole spacing designed to fit on 47° shank.


• This opener is designed to fit on the Bourgault shank better than the 600 Series.

410-KNF-7551

600-KNH-7552

600-KNH-7540

599-KNH-7540

FERTILIZER KNIVES


61

Hose Holder• Stainless steel hose holder.

• Mount on any C-shank.

• Completely height adjustable.

• Holds the NH3 hose in place.

Bolt and Nut Combo• Use to hold the 600 Series tips onto the 599 and 600 Series knife holders.

Chrome Tip• 3/4" chrome tip fits all 599 and 600 Series knife holders.

• Does not fit 600-KNH-7562.

Carbide Tip• 3/4" chrome tip with carbide on the nose fits all 599 and 600 Series knife holders.

• Does not fit 600-KNH-7562.

Carbide Tip with wing for liquid application• 3/4" carbide tip fits 600-KNH-7562.

• Allows vertical and horizontal separation when shooting liquid.

600-HHA-0750

600-BNC-5000

600-NUT-3754

600-BLT-5004

600-TIP-7500

600-TIP-7501

600-TIP-7507

FERTILIZER KNIVES ///

FERTILIZER ACCESSORIES

tillagetools.com

62 FERTILIZER KNIVES

Fits 47° and 50° C-Shank• Accepts 1-1/4" and 1-1/8" granular hose

(insert included).

• This opener comes standard with a 3/4" carbide tip. Inquire about other tip options.

• 675-ASY-1801GN accepts 1/2" (12 mm) hose for cold-flow anhydrous kits.

• 675-ASY-1801GM accepts Maxquip anhydrous systems.675-ASY-1801GM 675-ASY-1801GN

685-ASY-1801G 685-ASY-1801M

685-ASY-1801N 685-ASY-1801L 685-ASY-1801GM 685-ASY-1801GN

Fits Bourgault 3310 & 3320 PHD• Use on the Bourgault 3310 & 3320 Mid Row Shank.

• Deliver any one of the following fertilizers: granular, liquid, NH3 or NH3 Maxquip.

• 685-ASY-1801GM and 685-ASY-1801GN give you the flexibility to switch between products or place both products down at the same time.

• This opener comes standard with a 3/4" carbide tip. Inquire about other tip options.

• Fits 1/2" (12 mm) cold-flow anhydrous kits or Maxquip anhydrous systems.

• Accepts 1-1/2" granular hose.

MID ROW SHANKS

tillagetools.com


63FERTILIZER KNIVES ///


TILLAGEWhat’s in a sweep? Most sweeps on the market today are made with very comparable material. If the material used doesn’t set the sweep apart, then what makes the difference in the life and quality of a sweep?

• Precise Heat Treatment • Long-Lasting Design• Consistent Quality• Innovative Speed-Loc™

66

tillagetools.com

200 SERIESSPEED-LOC™ PRODUCTS

SIZE THICKNESS PRODUCT NO.

4" (100 mm) 1/4"(6 mm) 200-PWV-0400

5" (140 mm) 1/4" (6 mm) 200-PWV-0500

5" (140 mm) 5/16" (8 mm) 200-PWV-0508

7" (180 mm) 1/4" (6 mm) 200-PWV-0700

7" (180 mm) 5/16" (8 mm) 200-PWV-0708

9" (230 mm) 1/4" (6 mm) 200-PWV-0900

9" (230 mm) 5/16" (8 mm) 200-PWV-0908

10" (254 mm) 1/4" (6 mm) 200-PWV-1000

10" (254 mm) 5/16" (8 mm) 200-PWV-1008

11" (280 mm) 1/4" (6 mm) 200-PWV-1100

11" (280 mm) 5/16" (8 mm) 200-PWV-1108

12" (305 mm) 1/4" (6 mm) 200-PWV-1200

12" (305 mm) 5/16" (8 mm) 200-PWV-1208

13" (330 mm) 1/4" (6 mm) 200-PWV-1300

13" (330 mm) 5/16" (8 mm) 200-PWV-1308

14" (355 mm) 1/4" (6 mm) 200-PWV-1400

14" (355 mm) 5/16" (8 mm) 200-PWV-1408

16" (406 mm) 5/16" (8 mm) 200-PWV-1608*

18" (457 mm) 5/16" (8 mm) 200-PWV-1808*

This sweep is only available in 5/16" (8 mm) thickness and was developed for Western Europe. It is not recommended for most North American field conditions.

*Available in North America by special order only.

4"

7"

10"

12"

14"

5"

9"

11"

13"

16"

67


This “Goosefoot” tillage tool is 5/16" (8 mm) thick and 2-1/2" (63 mm) wide. It is designed specifically for vibrating S-tine cultivators.

This sweep is 1/4" (6 mm) thick and 4" (100 mm) wide. It is designed mainly for fall tillage or deep working. It has a hardened wear pad (52-56 HRC) which increases the life expectancy. The nose on this sweep runs 1/2" (12 mm) lower than the other 200 Series sweeps. This increased pitch improves penetration in hard or compacted ground.

This quick change spike is 5/8" (15 mm) thick, 2" (50 mm) wide and 4" (102 mm) long. It has a hardened wear pad (52-56 HRC) for extra life. This tool is made specifically for slurry injection.

This sweep is 5/16" (8 mm) thick and 4" (100 mm) wide with a 4" wide extended wear pad.

This sweep is 5/16" (8 mm) thick and 9" (230 mm) wide. The wear pad extends up the entire stem.

This quick change spike is 5/8" (15 mm) thick, 2-1/4" (57 mm) wide and 6" (150 mm) long. It has a hardened wear pad (52-56 HRC) for extra life. This tool is ideal for primary tillage or banding fertilizer.

This sweep is 5/16" (8 mm) thick and 4" (100 mm) wide. It is designed mainly for fall tillage or deep working. It has a hardened wear pad (52-56 HRC) which increases its life expectancy.

This quick change spike is 5/8" (15 mm) thick, 2-1/4" (57 mm) wide and 6" (150 mm) long. It has a hardened wear pad (52-56 HRC) that extends to the top of the stem to prevent wear in abrasive soil or when working at greater depths.

This sweep is 5/16" (8 mm) thick and 5" (127 mm) wide. It is designed mainly for fall tillage or deep working. It has a hardened wear pad (52-56 HRC) which increases its life expectancy.

TILLAGE /// SWEEPS AND SPIKES ///

200-GFO-0308

200-PWV-0405

200-SPK-0200

200-PWV-0428*

200-SPK-0215

200-PWV-0528*

200-SPK-0230

200-PWV-0738* 200-PWV-0928*

*Available in North America by special order only.

68

tillagetools.com

410 SERIESSPEED-LOC™ PRODUCTS


4" (100 mm) 1/4" (6 mm) 410-PWV-0400

6" (150 mm) 1/4" (6 mm) 410-PWV-0600

6" (150 mm) 5/16" (8 mm) 410-PWV-0608

8" (200 mm) 1/4" (6 mm) 410-PWV-0800

8" (200 mm) 5/16" (8 mm) 410-PWV-0808

10" (254 mm) 1/4" (6 mm) 410-PWV-1000

10" (254 mm) 5/16" (8 mm) 410-PWV-1008

12" (305 mm) 1/4" (6 mm) 410-PWV-1200

12" (305 mm) 5/16" (8 mm) 410-PWV-1208

14" (355 mm) 1/4" (6 mm) 410-PWV-1400

14" (355 mm) 5/16" (8 mm) 410-PWV-1408

16" (406 mm) 1/4" (6 mm) 410-PWV-1600

16" (406 mm) 5/16" (8 mm) 410-PWV-1608

18" (457 mm) 1/4" (6 mm) 410-PWV-1800

18" (457 mm) 5/16" (8 mm) 410-PWV-1808

6"

10"

14"

18"

4"

8"

12"

16"

69



Sweep with Hardened Wear Pad• 5/16" (8 mm) thick and 4" (100 mm) wide.

• 3/8" hardened wear pad (52-56 HRC) for longer life.

• Runs at a 13° pitch, which is steeper than the regular 410 sweep.

Sweep with Hardened Wear Pad• 5/16" (8 mm) thick and 5" (140 mm) wide.

• 3" hardened wear pad.

• Runs at a 3° pitch, which is the same as a standard sweep.

Spike• Heavy-duty quick change spike.

• 2" (50 mm) wide, 5/8" (15 mm) thick and 9" (230 mm) long.

• Hardened wear pad (52-56 HRC) for long life.

• Works well for primary tillage or for banding fertilizer.

410-PWV-0418

410-PWV-0518

410-SPK-0200

70

tillagetools.com

BOLT-ON SERIES


6" (150 mm) 1/4" (6 mm) 050-PWV-0600

8" (200 mm) 1/4" (6 mm) 050-PWV-0800

10" (254 mm) 1/4" (6 mm) 050-PWV-1000

050 SeriesFor heavy-duty chisel plows with 50° shanks and 2-1/4" (57 mm) hole centres.


8" (200 mm) 1/4" (6 mm) 043-PWV-0800

10" (254 mm) 1/4" (6 mm) 043-PWV-1000

12" (305 mm) 1/4" (6 mm) 043-PWV-1200

14" (355 mm) 1/4" (6 mm) 043-PWV-1400

16" (420 mm) 1/4” (6 mm) 043-PWV-1600

18" (460 mm) 1/4" (6 mm) 043-PWV-1800


4" (100 mm) 1/4" (6 mm) 047-PWV-0400

9" (230 mm) 1/4" (6 mm) 047-PWV-0900

10" (254 mm) 1/4" (6 mm) 047-PWV-1000

11" (280 mm) 1/4" (6 mm) 047-PWV-1100

12" (305 mm) 1/4” (6 mm) 047-PWV-1200

13" (330 mm) 1/4" (6 mm) 047-PWV-1300

Our bolt-on sweeps fit all makes and models of tillage equipment.

The Extended Stem AdvantageThe stem or neck on our bolt-on sweeps is longer than that of our competitors. This extended stem allows us to punch the bolt holes higher than on any other brand of sweeps. This reduces stem breaking and results in less wear on the shank and less wear and stone damage to the bottom bolt. Less wear on the shank extends the useful life of the sweep, and less stone damage on the bottom bolt means fewer problems when changing shovels. The extended stem feature saves you time and money.

043 SeriesFor heavy-duty chisel plows with 43° shanks and 2-1/4" to 2-1/2" (57 mm to 64 mm) hole centres.

047 SeriesFor field cultivators with 47° shanks and 1-3/4" (45 mm) hole centres.


12" (305 mm) 1/4" (6 mm) 050-PWV-1200

14" (355 mm) 1/4” (6 mm) 050-PWV-1400

16" (420 mm) 1/4" (6 mm) 050-PWV-1600

18" (460 mm) 1/4" (6 mm) 050-PWV-1800

Not sure which bolts you need? Refer to our bolt length chart on pages 78–80.

71



Reversible Spike• 2" (50 mm) wide, 5/8" (16 mm) thick and 14" (355 mm) long.

• 1-3/4" to 2-1/2" (45 to 57 mm) bolt hole spacing.

• Shorter than our other two reversible spikes, it is designed for light- to medium-duty field cultivators or for chisel plows where ground clearance in transport is a concern.

Reversible Spike• 2" (50 mm) wide, 5/8" (16 mm) thick and 17" (431 mm) long.

• 2-1/4" (57 mm) bolt hole spacing.

• Flat through the bolt hole section, it is designed specifically to fit the Bourgault chisel plow as well as the Morris LH 755 shank.

Reversible Spike• 2" (50 mm) wide, 5/8" (16 mm) thick and 16-1/2" (419 mm) long.


• Curved at the bolt hole section, it can be used on any chisel plow shank except the Bourgault and Morris LH 755 shank.

Reversible Chisel• 5/16" (8 mm) thick and 4" (100 mm) wide.

• 1-3/4" (45 mm) bolt hole spacing to fit light- and medium-duty field cultivators.

• Use mostly for primary tillage in the fall or early spring.

Reversible Chisel• 5/16" (8 mm) thick and 4" (100 mm) wide.


• Use mostly for primary tillage in the fall or early spring.

070-RSP-0200A

070-RSP-0210A

070-RSP-0220A

070-RCH-0451

070-RCH-0452

tillagetools.com

72 ACCESSORIES

200-DRV-1030

This driver should be used when installing the following openers: 200-KNF-0505, 200-VRT-1000, 200-VRT-1011, 200-VRT-1016, 200-VRT-1061 and 410-VRT-1000. It should also be used when installing knives with the following tips: 200-TIP-0503, 200-TIP-0507, 200-TIP-0523, 200-TIP-0524, 200-TIP-0531 and 200-TIP-1011.

100-DRV-1010

This driver should be used for installing the following knives: 200-KNF-0861, 200-KNF-0863, 200-KNF-7510, 200-KNF-7511, 200-KNF-7518, 200-KNF-7542, 200-KNF-7520, 200-KNF-7521, 200-KNF-7524, 200-KNF-7525, 200-KNF-7530 and 200-KNF-7531.

100-DRV-1020

This driver is used when installing the 200-HOE-1700 onto the adapter.

200-DRV-1013

This driver should be used when installing knives with the following tips: 200-TIP-2011, 200-TIP-0300, 200-TIP-3001, 200-TIP-3011 and 200-TIP-4011. It should also be used when installing the 200-KNF-0501, 200-KNF-0571 and 200-KNF-0575.

200-BNC-3100

Stainless steel square nut and bolt. Used to secure any quick change tip. This combination is made up of 200-BLT-3102 and 200-NUT-3101.

200-DRV-1012

This driver should be used for installing the 200-KNF-0813.

100-WDG-0700

This 7° urethane wedge is designed to correct the pitch of the 100-QCA-5010 and the 200-QCA-5010 adapters on 43° shanks.

200-WDG-0206

This 2° urethane wedge has 45 mm to 80 mm bolt hole spacing. It is used to obtain proper sweep pitch on certain shanks.

200-WDG-0506


200-WDG-1000 200-WDG-1006



400-WDG-0300

This 3° urethane wedge is designed to correct the pitch of the 410-QCA-5010 adapter on a 47° chisel plow shank, as well as the 50° bolt-on sweeps.

400-WDG-0700

This 7° urethane wedge is designed to correct the pitch of the 410-QCA-5010 adapter when installing on a 43° shank. It should also be used with the 600 Series knives when installing on a 43° shank.

880-WDG-0301

This cast wedge adapter is designed for our 047, 610 and 612 seeding openers on all 50° curved bottom shanks including the John Deere 1830 but excluding all other John Deere models.

200-QAS-4711

This sub-plate is used in conjunction with the 200-QCA-4710 adapter on the Kongskilde VFM shank.

200-QAS-4712

This sub-plate is used in conjunction with the 200-QCA-4710 adapter on an S-tine. S-tines with a single hole can now use the Speed-Loc™ system.

880-WDG-0300

This cast wedge adapter is designed for our 047, 610 and 612 seeding openers on all John Deere shanks except the John Deere 1830.


73ACCESSORIES ///

400-DRV-1000

This driver can be used when installing any of the quick change sweeps and spoons.

400-DRV-1010

This driver should be used when installing the following knives: 200-KNF-0810, 200-KNF-0811, 410-KNF-0800 and 410-KNF-0801. It should also be used for installing knives with the following tips: 200-TIP-0800 and 200-TIP-0801.

100-HAM-4000

This 4 lb (1.8 kg) hammer is ideal for installing all quick change products.

200-REL-1010 047-ACC-1001

The speed-release tool must be used to remove 200 and 410 Series sweeps and openers off the Speed-Loc™ adapters.

Helps direct the flow of seed in a focused row behind the opener. Use with 047-ASY-1000 or 675 Series openers.

680-ACC-1000

Helps direct the flow of seed in a focused row behind the opener. Use with 680-ASY-1000 openers prior to 2012.

300-BSH-1200

This bushing adapts from a 1-1/8" (28 mm) O.D. air hose up to a 1-1/4" (31 mm) O.D. air hose.

300-BSH-1205

This bushing adapts from 1-1/8" (28 mm) O.D. air hose to 1-1/8" (28 mm) O.D. air hose.

880-BSH-1130

This bushing is needed when you are using 1-1/8" (28 mm) hose.

880-HCL-0001

This clip eliminates hose movement, as the sharp corners imbed into the granular pipe.

880-CPL-2500

This coupler is used to attach an 1-1/4" O.D. liquid phosphorous tube. Included with all new liquid phosphorous openers.

880-BSH-1150

This bushing adapts from 1-1/4" (31 mm) O.D. air hose up to a 1-1/2" (31 mm) O.D. air hose.

880-ORF-0001880-HCL-0002

This orifice is used to concentrate and direct the flow of liquid fertilizer on the 200-VRT-1061 and 200-KNF-0863.

Spacer clip may be required on the rear tube of the following side band openers: 683, 684, 686, 693, 694 where 1-1/8" hose is used.

047-ACC-1002

Allows you to adapt to any shank with an open bottom hole. Keeps the bottom bolt in place on the John Deere 1820, 1830 & 2400.

880-ASY-1000 680-ACC-0001

Adapt a .085 mm Maxquip system with our NH3 (1/2") fertilizer openers. This kit gives you everything you need to adapt to an existing line.

Spacer plate is required for the Concord when installing any Edge-On product.

74

tillagetools.com

PRODUCT DEPTH CHART0

47-K

NH

-10

00

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-08

00

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-08

01

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-30

00

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-30

01

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-30

11

050

-KN

H-0

810

& 0

812

W/ 2

00

-TIP

-10

11

200

-HO

E-17

00

200

-KN

F-0

80

0 &

08

01

200

-KN

F-0

80

3

200

-KN

F-0

86

3 &

08

61

200

-KN

F-75

11, 7

510

, 751

8, 7

542

200

-KN

F-75

20, 7

521,

752

4, 7

525,

753

0, 7

531

200

-KN

H-0

500

W/ 2

00

-TIP

-052

3

200

-KN

H-0

510

W/ 2

00

-TIP

-050

3

200

-KN

H-0

510

W/ 2

00

-TIP

-050

7

200

-KN

H-4

010

W/ 2

00

-TIP

-08

00

200

-KN

H-4

010

W/ 2

00

-TIP

-08

01

200

-KN

H-4

010

W/ 2

00

-TIP

-30

00

200

-KN

H-4

010

W/ 2

00

-TIP

-30

01

200

-KN

H-4

010

W/ 2

00

-TIP

-30

11

200

-KN

H-4

010

W/ 2

00

-TIP

-10

11

200

-PW

V-0

405

200

-PW

V-0

400

TO 2

00

-PW

V-1

200

200

-PW

V-1

300

& 14

00

200

-PW

V-0

508

TO 2

00

-PW

V-1

208

200

-PW

V-0

518

200

-PW

V-1

308

& 14

08

200

-SP

N-0

200

, 020

8, 0

300

, 030

8

200

-SP

K-0

200

& 0

215

200

-VR

T-10

11, 1

00

0, 1

016

, 10

40

200

-VR

T-10

61

599-

KN

H-7

512

& 7

540

W/ 6

00

-TIP

-750

0 &

750

1

050

-KN

H-0

500

W/ 2

00

-TIP

-052

3

050

-KN

H-0

810

W/ 2

00

-TIP

-08

00

050

-KN

H-0

810

W/ 2

00

-TIP

-10

11

050

-KN

H-0

812

W/ 2

00

-TIP

-08

00

050

-KN

H-0

812

W/ 2

00

-TIP

-10

11

410

-KN

F-0

80

0 &

08

01

410

-KN

F-0

824

& 0

825

410

-KN

F-0

830

& 0

831

410

-KN

H-0

500

W/ 2

00

-TIP

-052

3

410

-KN

H-4

00

0 W

/ 20

0-T

IP-0

80

1

410

-PW

V-0

400

410

-PW

V-0

600

& 0

608

410

-PW

V-0

80

0 &

08

08

410

-PW

V-1

00

0 &

100

8

410

-PW

V-1

200

& 12

08

410

-PW

V-1

400

& 14

08

410

-PW

V-1

600

& 16

08

410

-PW

V-1

80

0 &

180

8

410

-SP

K-0

200

410

-SP

N-0

300

& 0

308

600

-KN

H-7

510

W/ 6

00

-TIP

-750

1

600

-KN

H-7

520

W/ 6

00

-TIP

-750

1

600

-KN

H-7

530

W/ 6

00

-TIP

-750

1

600

-KN

H-7

540

W/ 6

00

-TIP

-750

1

600

-KN

H-7

550

W/ 6

00

-TIP

-750

1

600

-KN

H-7

561 W

/ 60

0-T

IP-7

501

600

-KN

H-7

562

W/ 6

00

-TIP

-750

1

200 SERIES

410 SERIES

DEP

TH IN

INCH

ESD

EPTH

IN IN

CHES

0

1

2

3

4

5

6

0

1

2

3

4

5

6

75


SPEED-LOC™ REPLACEMENT PARTS

Note: a complete package for the 410 Series can be ordered including bushing, spring ball, pin and dust seal. Order part number 410-SLC-1050.

Replacement bushing for all 200 Series adapters as well as the 410-QCA-5050. Comes complete with dust seal.

Replacement spring ball for the 200-QCA-4710, 200-QCA-5000 and 200-QCA-5010 adapters.

Replacement bushing for the 410-QCA-5000, 410-QCA-5010 and 410-QCA-5020. Comes complete with dust seal.

Replacement spring ball for the 200-QCA-4700 adapters.

Replacement spring ball for 200-QCA-5030 adapters.

Replacement dust seal for all 200 and 410 Series Speed-Loc™ adapters.

Replacement spring ball for the 200-QCA-5020 and 410-QCA-5050 adapters.

Replacement locking pin for all the 410 Series adapters*. Go to 200-SLC-1020 if 410 Series adapter was purchased after Nov. 1/08.

*Prior to Nov. 1/08

Replacement locking pin for all 200 and 410* Series adapters.

*After Nov. 1/08

Replacement spring ball for 200-QCA-5020 adapter for special applications.

Replacement spring ball for the 410-QCA-5000, 410-QCA-5010 and 410-QCA-5020.

200-SLC-1001

200-SLC-1035

410-SLC-1001

200-SLC-1010

200-SLC-1037

410-SLC-1022*

200-SLC-1020

200-SLC-1038

410-SLC-1030

200-SLC-1030

200-SLC-1039

76

tillagetools.com

SPEED-LOC™ ADAPTER CHARTFOR NORTH AMERICA & AUSTRALIA

200 SERIES 410 SERIES

MAKE & MODEL SHA

NK

DEG

REE

BO

LT S

IZE

HO

LE C

ENTR

E

200

-QCA

-470

0

200

-QCA

-471

0

200

-QCA

-500

0

200

-QCA

-50

10

200

-WD

G-0

700

410

-QCA

-500

0

410

-QCA

-50

10

410

-WD

G-0

300

410

-WD

G-0

700

800

-WD

G-0

300

AFM180, 200, 250, 880 43° 7/16 1-3/4150, 2300, 310, 300 50° 1/2 2-1/4350 SCARICHISEL 50° 1/2 2-1/4ANDERSONFIELD CULTIVATORS 47° 3/8 1-3/4CHISEL PLOWS 50° 1/2 2-1/4BOURGAULTFIELD CULTIVATORS 6200, 6800, 8800, 8810, 8910 47° 1/2 1-3/4

5710, 5810 AIR DRILL 47° 1/2 1-3/4CHISEL PLOWS 9200, 9400, 9800 50° 1/2 2-1/4

3310, 3320 EDGE-ON (NO ADAPTER FOR THIS APPLICATION)BRADYFIELD CULTIVATORS 43° 3/8 1-5/8 (NO ADAPTER FOR THIS APPLICATION)CHISEL PLOWS 50° 7/16 2-1/4BRILLIONHFCT MO 47° 7/16 1-5/8BUSH HOGFIELD CULTIVATORS 47° 3/8 1-3/4CHISEL PLOWS 50° 7/16 2-1/4CASEFC, FCW, FCM, 10, 50, 55, 645 47° 3/8 1-3/44700, 4900, 5000, 645 43° 1/2 2-1/4CASE IH45, 4300, 4500, 4600, 4700, 4800, 4900 47° 7/16 1-3/4

VIBRASHANK 47° 7/16 1-3/4VIBRACHISEL 5600, 5700 43° 1/2 2-1/4

5800, 5850, 5900 50° 1/2 2-1/4PTX 300, PTX 600 50° 1/2 2-1/4ATX AIR DRILL WITH EDGE-ON 84° SHANK (NO ADAPTER FOR THIS APPLICATION)

ATX 400, 700 AIR HOE DRILL 350 LB OR 550 LB TRIP 50° 1/2 2-1/4

CONCORDC-SHANKS 50° 1/2 2-1/4EDGE-ON SHANKS (NO ADAPTER FOR THIS APPLICATION)CCIL202, 179, 279, 379 47° 3/8 1-3/4203, 204, 205 43° 1/2 2-1/2806, 807, 808 43° 1/2 2-1/2CHISEL PLOW (THICK SHANK) 50° 7/16 2-1/4

CNH (DMI)FIELD CULTIVATORS 47° 7/16 1-3/4DEGELMANFIELD CULTIVATORS 47° 7/16 1-3/4500 50° 7/16 2-1/43000-2 50° 7/16 2-1/4DEMSTERCHISEL PLOWS 54° 7/16 2-1/4 (NO ADAPTER FOR THIS APPLICATION)EDWARDSCHISEL PLOWS 50° 7/16 2-1/4FORWARDBOURGAULT TYNE280, 2700, 2800, 8800 47° 1/2 1-3/4FUSION DELTA 47° 1/2 1-3/43000 & 400 SERIES C/P 50° 1/2 2-1/4


MAKE & MODEL SHA

NK

DEG

REE

BO

LT S

IZE

HO

LE C

ENTR

E

200

-QCA

-470

0

200

-QCA

-471

0

200

-QCA

-500

0

200

-QCA

-50

10

200

-WD

G-0

700

410

-QCA

-500

0

410

-QCA

-50

10

410

-WD

G-0

300

410

-WD

G-0

700

800

-WD

G-0

300

EZEE-ONFIELD CULTIVATORS 3500, 3550, 5550 47° 1/2 1-3/4

6000 WITH FIELD CULTIVATOR SHANK OPTION 47° 1/2 1-3/4

6000 WITH CHISEL PLOW SHANK OPTION 50° 1/2 2-1/4

ALL CHISEL PLOWS INCLUDING 7450 50° 1/2 2-1/4

7560, 7550 47° 1/2 1-3/4FLEXI-COIL200, 400, 800 47° 7/16 1-3/4300, 340, 600 50° 1/2 2-1/2820 & ST820 WITH 350 LB & 550 LB TRIPS 47° 1/2 2-1/2

820 & ST820 WITH 550 LB & 650 LB TRIPS 50° 1/2 2-1/4

5000 & 7500 DEPENDING ON SHANK OPTION 47° 1/2 2-1/2

5000 & 7500 DEPENDING ON SHANK OPTION 50° 1/2 2-1/2

EDGE-ON (NO ADAPTER FOR THIS APPLICATION)5000HD & 5500 AIR HOE DRILL 350 LB OR 550 LB TRIP 50° 1/2 2-1/2

FRIGGSTADFIELD CULTIVATORS 47° 7/16 1-3/4CHISEL PLOWS (OLDER MODELS) 50° 7/16 2-1/4

CHISEL PLOWS 50° 1/2 2-1/4GASON5100 SERIES 46° 7/16 1-3/4SCARITILL & EH SCARITILL 47° 1/2 BOTH7100 ECOTILL 50° 1/2 2-1/4GESSNERHR 1200 50° 1/2 2-1/4GLENCOEPC, MPC, PCMW 47° 3/8 1-3/4CHISEL PLOWS 47° 7/16 2-1/4HIGH CLEARANCE 50° 7/16 1-2/4GRAHAMCHISEL PLOWS 50° 1/2 2-1/4400, 500, 1600, 2600 54° 7/16 2-1/4 (NO ADAPTER FOR THIS APPLICATION)GREAT PLAINS8000, 7000 47° 7/16 1-3/4GYRAL IMPLEMENTSPENETRATOR T23, T25 43° 1/2 BOTHAG BNOSS T30 43° 7/16 BOTHGYSLERCHISEL PLOWS 47° 7/16 2-1/4HESSTONFIELD CULTIVATORS 47° 1/2 1-3/4CHISEL PLOWS 50° 1/2 2-1/4HINIKERFIELD CULTIVATORS 47° 7/16 1-3/4CHISEL PLOWS 50° 1/2 2-1/4HORWOOD BAGSHAW350 SCARIBAR EDGE-ON 47° 1/2 1-3/4HORWARDCHISEL PLOWS** 50° 9/16 2-1/4INTERNATIONAL45, 46, 47 47° 7/16 1-3/410, 50, 55, 75, 509, 645 43° 1/2 2-1/4

* FOR KNIFE OPENERS ONLY

77


REFERENCE ///


MAKE & MODEL SHA

NK

DEG

REE

BO

LT S

IZE

HO

LE C

ENTR

E

200

-QCA

-470

0

200

-QCA

-471

0

200

-QCA

-500

0

200

-QCA

-50

10

200

-WD

G-0

700

410

-QCA

-500

0

410

-QCA

-50

10

410

-WD

G-0

300

410

-WD

G-0

700

800

-WD

G-0

300

JANKEUNIV DIRECT DRILL 50° 1/2 2-1/4U/D DRILL (HYD) EARLY 50° 1/2 2-1/4JEOFFROY450 47° 3/8 1-3/4JOHN DEERE1000, 1010, 1050 43° 3/8 1-5/8 (NO ADAPTER FOR THIS APPLICATION)726, 2210, 2200 47° 7/16 1-3/4940, 960, 985 47° 7/16 1-3/4730 47° 1/2 1-3/4735, 737, 610, 680, 685, 1600, 1610, 1650 50° 1/2 2-1/4

1810, 1820, 1830, 1835 WITH 350 LB TRIPS 47° 1/2 1-3/4

1810, 1820, 1830, 1835 WITH 500 LB TRIPS 50° 1/2 2-1/4

2400, 2410 50° 1/2 2-1/4JOHN SHEARERUNIVERSAL CULTIVATOR 47° 7/16 1-3/4CHISEL PLOWS 50° 1/2 2-1/4KONGSKILDEC-SHANK 47° 1/2 1-3/4S-TINE 47° 7/16 1-5/8KRAUSE600, 900, 3100, 4200 47° 7/16 1-3/44000 50° 1/2 2-1/45630, 5635 47° 1/2 1-3/4LEONCP77 43° 7/16 2-1/4ALL OTHER LEON CHISEL PLOWS 50° 1/2 2-1/4

FIELD CULTIVATORS 47° 7/16 1-3/4MASSEY FERGUSON160 47° 3/8 1-3/4259 47° 7/16 1-3/4124, 125, 126, 128, 133 54° 7/16 2-1/4 (NO ADAPTER FOR THIS APPLICATION)MF 7300 CHISEL PLOW 50° 1/2 2-1/4MORRISL225, L233, L240, L320 47° 3/8 1-3/4CHALLENGER II, 9000, 9100 47° 1/2 1-3/4

MAXIM, MAXIM II 47° 1/2 1-3/4MAXIM III 47° 1/2 1-3/4CONCEPT 2000 WITH 400 LB TRIP 47° 1/2 1-3/4

CONCEPT 2000 WITH 550 LB TRIP 47° 1/2 1-3/4

CONCEPT 2000 WITH LH 755 LB TRIP 50° 1/2 2-1/4

220, 4, 5, 6, 7 43° 7/16 2-1/4MAGNUM I 43° 1/2 2-1/4912, 8900, 9000, MAGNUM II 50° 1/2 2-1/4MAGNUM III WITH LH 755 LB TRIP 50° 1/2 2-1/4

EDGE-ON (CONTOUR DRILL) (NO ADAPTER FOR THIS APPLICATION)CHALLENGER L2 480 47° 3/8 1-3/4NEW HOLLANDSD 440A, SD 550A AIR HOE DRILL (DEPENDING ON SHANK OPTION)

47° 1/2 1-3/4

SD 440A, SD 550A AIR HOE DRILL (DEPENDING ON SHANK OPTION)

50° 1/2 2-1/4


MAKE & MODEL SHA

NK

DEG

REE

BO

LT S

IZE

HO

LE C

ENTR

E

200

-QCA

-470

0

200

-QCA

-471

0

200

-QCA

-500

0

200

-QCA

-50

10

200

-WD

G-0

700

410

-QCA

-500

0

410

-QCA

-50

10

410

-WD

G-0

300

410

-WD

G-0

700

800

-WD

G-0

300

ST 540 CHISEL PLOW 50° 1/2 2-1/4ST 250 47° 1/2 1-3/4ST 830 WITH 350 LB TRIP 47° 1/2 1-3/4ST 830 WITH 550 LB TRIP (DEPENDING ON SHANK OPTION)

47° 1/2 1-3/4

ST 830 WITH 550 LB TRIP (DEPENDING ON SHANK OPTION)

50° 1/2 2-1/4

ST 830 WITH 650 LB TRIP 50° 1/2 2-1/4P2050, P2060 AIR HOE DRILL 350 LB OR 550 LB TRIP 50° 1/2 2-1/4

NOBLEXR20 50° 7/16 2-1/48000, 4000 MULTI-TOOL 50° 1/2 2-1/4QUINSTARFIELD FINISHER 47° 7/16 1-3/4FALLOW MASTER III 50° 1/2 2-1/4RYAN (RFM)1000 SERIES 47° 7/16 1-3/4SALFORDFIELD CULTIVATOR 47° 7/16 1-3/4SCHULTE1000 SERIES 50° 7/16 2-1/4SMALEMULTIVATOR 47° 7/16 1-3/4CHISEL PLOWS 50° 1/2 2-1/4SUMMERSSUPERCHISEL 50° 1/2 2-1/4SUNFLOWERCHISEL PLOWS 50° 1/2 2-1/45000, 6000, 7000 47° 7/16 1-3/4TAYLORFIELD CULTIVATORS 47° 3/8 1-3/4UNVERFERTHPERFECTA II FIELD CULTIVATORS 47° 7/16 1-3/4

VERSATILEDH730, DH750 WITH 350 LB & 550 LB TRIPS 47° 1/2 1-3/4

C500 WITH 350 LB & 550 LB TRIPS 47° 1/2 1-3/4

C600 WITH 350 LB & 550 LB TRIPS 47° 1/2 1-3/4

C600 WITH 600 LB TRIP 50° 1/2 2-1/4C700 WITH 650 LB TRIP 50° 1/2 2-1/4VICTORYCHISEL PLOWS 50° 1/2 2-1/4WIL-RICHFIELD CULTIVATORS 47° 7/16 1-3/4CHISEL PLOWS (1993 & OLDER) 43° 7/16 2-1/4

CHISEL PLOWS (1994 & NEWER) 50° 1/2 2-1/4

XL2, QX2 47° 7/16 1-3/4YEOMANS GRAHAM HOEMESUS CHISEL PLOWS 50° 1/2 2-1/4

*Sweeps will not work with this combination, knives only. **Bolt sizes will require adapting.

78

tillagetools.com

BOLT LENGTH CHART

047 Series Bolt-On Sweeps on light- and medium-duty cultivatorsAPPLICATION BOTTOM BOLT TOP BOLT SPECIAL NOTES

1" Bourgault shank without seed boot 1/2" x 2" 1/2" x 2" Plow bolts, no lock washer, regular nut

1" Bourgault shank with Bourgault round tube seed boot 1/2" x 2" 1/2" x 2" Plow bolts, no lock washer, regular nut

1" Bourgault shank with Bourgault square tube seed boot 1/2" x 2" 1/2" x 2-1/4" Plow bolts, no lock washer, regular nut

7/8" Bourgault shank without seed boot 1/2" x 1-3/4" 1/2" x 1-3/4" Plow bolts, no lock washer, regular nut

7/8" Bourgault shank with Bourgault round tube seed boot 1/2" x 1-3/4" 1/2" x 2" Plow bolts, no lock washer, regular nut

7/8" Bourgault shank with Bourgault square tube seed boot 1/2" x 1-3/4" 1/2" x 2-1/4" Plow bolts, no lock washer, regular nut

3/4" Bourgault shank without seed boot 1/2" x 1-3/4" 1/2" x 1-3/4" Plow bolts, no lock washer, regular nut

3/4" Bourgault shank with Bourgault round tube seed boot 1/2" x 1-3/4" 1/2" x 1-3/4" Plow bolts, no lock washer, regular nut

3/4" Bourgault shank with Bourgault square tube seed boot 1/2" x 1-3/4" 1/2" x 2" Plow bolts, no lock washer, regular nut

3/4" Degelman shank without seed boot 7/16" x 1-3/4" 7/16" x 1-3/4" Plow bolts, no lock washer, regular nut

7/8" Flexi-Coil shank without seed boot 7/16" x 1-3/4" 7/16" x 1-3/4" Plow bolts, no lock washer, regular nut

1/2" Morris Challenger shank without seed boot 3/8" x 1-1/2" 3/8" x 1-1/2" Plow bolts, no lock washer, regular nut

5/8" Morris Challenger shank without seed boot 3/8" x 1-1/2" 3/8" x 1-1/2" Plow bolts, no lock washer, regular nut

5/8" John Deere shank without seed boot 7/16" x 1-1/2" 7/16" x 1-1/2" Plow bolts, no lock washer, regular nut

9/16" CIL shank without seed boot 3/8" x 1-1/2" 3/8" x 1-1/2" Plow bolts, no lock washer, regular nut

1/2" Case IH shank without seed boot 7/16" x 1-1/2" 7/16" x 1-1/2" Plow bolts, no lock washer, regular nut

043 & 050 Series Bolt-On Sweeps on heavy-duty chisel plowsAPPLICATION BOTTOM BOLT TOP BOLT SPECIAL NOTES

1" Bourgault shank without seed boot 1/2" X 2" 1/2" X 2" Plow bolts, no lock washer, regular nut

1" Bourgault shank with Bourgault splitter seed boot #6505-42 1/2" X 2" 1/2" X 2-1/4" Plow bolts, no lock washer, regular nut

1-1/4" Bourgault shank without seed boot 1/2" X 2-1/4" 1/2" X 2-1/4" Plow bolts, no lock washer, regular nut

1-1/4" Bourgault shank with Bourgault splitter seed boot #6505-42 1/2" X 2-1/4" 1/2" X 2-1/2" Plow bolts, no lock washer, regular nut

1" John Deere shank without seed boot 1/2" X 2" 1/2" X 1-3/4" Plow bolts, no lock washer, regular nut

3/4" Degelman shank (50°) without seed boot 1/2" X 1-3/4" 1/2" X 1-3/4" Plow bolts, no lock washer, regular nut

1-1/4" Flexi-Coil shank without seed boot 1/2" X 2-1/4" 1/2" X 2-1/4" Plow bolts, no lock washer, regular nut

1" Morris shank (43°) without seed boot 1/2" X 2" 1/2" X 2" Plow bolts, no lock washer, regular nut

7/8" Shulte shank without seed boot 1/2" X 2" 1/2" X 2" Plow bolts, no lock washer, regular nut

1-1/4" CIL shank without seed boot 1/2" X 2-1/4" 1/2" X 2-1/4" Plow bolts, no lock washer, regular nut

1-1/4" IH shank without seed boot 1/2" X 2-1/4" 1/2" X 2-1/4" Plow bolts, no lock washer, regular nut

3/4" Case IH Vibra shank without seed boot 1/2" x 1-3/4" 1/2" x 1-3/4" Plow bolts, no lock washer, regular nut

NOTES: 1) All Bourgault sweeps come with 1/2" holes. Shanks with 3/8" and 7/16" holes require special oversize (O/S) head plow bolts. 2) When bolting a seed boot, usually it is the bottom bolt which bolts the seed boot to the shank; the top bolt should remain the same length as listed above. If the seed boot cross section at the point the bolt goes through is 1/8" thick or less, use the same bolt length as above without the lock washer. If the seed boot cross section at the point the bolt goes through is greater than 1/8", increase bolt length by adding the measured cross section of the seed boot at the point the bolt goes through to the above lengths.

79


REFERENCE ///

200 Series QC Adapter – 200-QCA-4700APPLICATION BOTTOM BOLT TOP BOLT SPECIAL NOTES

1" Bourgault shank without seed boot 1/2" x 2-1/4" no lock washer 1/2" x 2-1/4" no lock washer Hex-head bolts

1" Bourgault shank with round tube Bourgault seed boot 1/2" x 2" no lock washer 1/2" x 2-1/4" no lock washer Hex-head bolts, grade 8 required

1" Bourgault shank with square tube Bourgault seed boot 1/2" x 2" no lock washer 1/2" x 2-1/2" no lock washer Hex-head bolts, grade 8 required

7/8" Bourgault shank without seed boot 1/2" x 2" no lock washer 1/2" x 2" no lock washer Hex-head bolts

7/8" Bourgault shank with round tube Bourgault seed boot 1/2" x 2" no lock washer 1/2" x 2-1/4" no lock washer Hex-head bolts, grade 8 required

7/8" Bourgault shank with square tube Bourgault seed boot 1/2" x 2" no lock washer 1/2" x 2-1/4" no lock washer Hex-head bolts, grade 8 required

3/4" Bourgault shank without seed boot 1/2" x 2" no lock washer 1/2" x 2" no lock washer Hex-head bolts

3/4" Bourgault shank with round tube Bourgault seed boot 1/2" x 1-3/4" no lock washer 1/2" x 2" c/w with lock washer Hex-head bolts

3/4" Bourgault shank with square tube Bourgault seed boot 1/2" x 1-3/4" no lock washer 1/2" x 2-1/4" with lock washer Hex-head bolts

3/4" Ezee-On shank without seed boot 7/16" x 1-3/4" 7/16" x 1-3/4" Hex-head bolts (see note 3 below)

7/8" Ezee-On shank without seed boot 7/16" x 2" 7/16" x 2" Hex-head bolts (see note 3 below)


3/4" and 7/8" Flexi-Coil shank without seed boot 7/16" x 2-1/4" no lock washer 7/16" x 2-1/4" no lock washer Plow bolt (see note 2 below)

7/8" Flexi-Coil shank with 5649 seed boot 7/16" x 3-7/8" no lock washer 7/16" x 2-1/2" no lock washer Plow bolt (see note 2 below)

1/2" Morris Challenger shank without seed boot 3/8" x 1-3/4" no lock washer 3/8" x 1-3/4" no lock washer Plow bolt (see note 2 below)

5/8" Morris Challenger shank without seed boot 3/8" x 2" no lock washer 3/8" x 2" no lock washer Plow bolt (see note 2 below)

7/8" Morris shank without seed boot 7/16" x 2-1/4" no lock washer 7/16" x 2-1/4" no lock washer Plow bolt (see note 2 below)

9/16" CIL shank without seed boot 3/8" x 2" no lock washer 3/8" x 2" no lock washer Plow bolt (see note 2 below)

5/8" John Deere shank without seed boot 7/16" x 2" no lock washer 7/16" x 2" no lock washer Plow bolt (see note 2 below)

3/4" Degelman shank 7/16" x 2-1/4" no lock washer 7/16" x 2-1/4" no lock washer Plow bolt (see note 2 below)

9/16" Wil-rich shank without seed boot 1/2" x 2" no lock washer 1/2" x 2" no lock washer Plow bolt


1" shank without seed boot or wedge 1/2" x 2-1/2" with lock washer 1/2" x 2-1/2" with lock washer Plow bolt

1-1/4" shank without seed boot seed boot or wedge 1/2" x 2-3/4" with lock washer 1/2" x 2-3/4" with lock washer Plow bolt

NOTES: 1) Above bolt lengths are determined using prevailing torque side locknuts – grade C. This special locknut is necessary to keep the adapter tight. It is very important to use it, especially in stony or hard ground conditions. 2) Grade 8 bolts are required with the Bourgault 7/8" and 1" shanks where seed boots are involved. If not used, bolt loosening may occur. 3) Shanks with 7/16" holes require the special oversize head hex bolt.

NOTES: 1) Above bolt lengths are determined using prevailing torque side locknuts – grade C. This special locknut is necessary to keep the adapter tight. 2) Shanks with 3/8" and 7/16" holes require special oversize head plow bolts. 3) When bolting a seed boot, usually it is the bottom bolt which bolts the seed boot to the shank; the top bolt should remain the same length as listed above. If the seed boot cross section at the point the bolt goes through is 1/8" thick or less, use the same bolt length as above without the lock washer. If the seed boot cross section at the point the bolt goes through is greater than 1/8", increase bolt length by adding the measured cross section of the seed boot at the point the bolt goes through to the above lengths.

80

tillagetools.com

BOLT LENGTH CHART

410 Series QC Adapter – 410-QCA-5000APPLICATION TOP HOLE BOTTOM HOLE SPECIAL NOTES

1" Bourgault shank without seed boot 1/2" x 2-1/2" 1/2" x 2-1/2” Hex-head

1" Bourgault shank with Bourgault splitter seed boot 6505-42 1/2" x 2-1/2" 1/2" x 2-3/4" Hex-head

1-1/4" Bourgault shank without seed boot 1/2" x 2-3/4" 1/2" x 2-3/4" Hex-head

1-1/4" Bourgault shank with Bourgault splitter seed boot 6505-42 1/2" x 2-3/4" 1/2" x 3" Hex-head

410 Series QC Adapter – 410-QCA-5010APPLICATION TOP HOLE BOTTOM HOLE SPECIAL NOTES

1" shank without seed boot or wedge 1/2" x 2-1/2" 1/2" x 2-1/2” Hex-head

1-1/4" shank without seed boot or wedge 1/2" x 2-3/4" 1/2" x 2-3/4" Hex-head

600 Series Quick Tip KnivesAPPLICATION TOP HOLE BOTTOM HOLE SPECIAL NOTES

For 47° and 50° applications, no wedge is needed

1-1/4" Bourgault shank 1/2" x 2-3/4" 1/2" x 2-3/4" Hex-head bolt, regular nut and lock

1" Bourgault shank 1/2" x 2-1/2" 1/2" x 2-1/2" Hex-head bolt, regular nut and lock

7/8" Bourgault shank 1/2" x 2-1/2" 1/2" x 2-1/2" Hex-head bolt, regular nut and lock

3/4" Bourgault shank 1/2" x 2-1/4" 1/2" x 2-1/4" Hex-head bolt, regular nut and lock

1-1/4" Flexi-Coil shank 1/2" x 2-3/4" 1/2" x 2-3/4" Hex-head bolt, regular nut and lock

1-1/4" Morris shank 1/2" x 2-3/4" 1/2" x 2-3/4" Hex-head bolt, regular nut and lock (see note 1 below)

1" John Deere shank 1/2" x 2-1/2" 1/2" x 2-1/2" Hex-head bolt, regular nut and lock

7/8" Shulte shank 1/2" x 2-1/2" 1/2" x 2-1/2" Hex-head bolt, regular nut and lock

3/4" Degelman shank 1/2" x 2-1/4" 1/2" x 2-1/4" Hex-head bolt, regular nut and lock

For 43° applications, wedge 400-WDG-0700 is required

1" Morris shank for NH3 knives 1/2" x 3" no lock washer 1/2" x 2-3/4" no lock washer Hex-head, regular nut

1" Morris shank for granular knives 1/2" x 3" no lock washer 1/2" x 2-3/4" no lock washer Hex-head, regular nut

1-1/4" CIL shank, 2-1/2" hole centre-to-centre 1/2" x 3-1/4" c/w no lock washer 1/2" x 2-3/4" no lock washer Hex-head, regular nut

1-1/4" IH shank 1/2" x 3-1/4" 1/2" x 3" Hex-head bolt, regular nut and lock (see note 2 below)

3/4" Case IH vibra chisel shank 1/2" x 2-3/4" 1/2" x 2-1/2" Hex-head bolt, regular nut and lock

NOTES: 1) Above bolt lengths are determined using prevailing torque side locknuts – grade C. This special locknut is necessary to keep the adapter tight. 2) When bolting a seed boot, usually it is the bottom bolt which bolts the seed boot to the shank; the top bolt should remain the same length as listed above. If the seed boot cross section at the point the bolt goes through is 1/8" thick or less, use the same bolt length as above without the lockwasher. If the seed boot cross section at the point the bolt goes through is greater than 1/8", increase bolt length by adding the measured cross section of the seed boot at the point the bolt goes through to the above lengths. 3) When bolting an adapter using a wedge, a wedge will only be used when using the 410-QCA-5010 adapter on 43° and 47° chisel plows. Measure the cross section of the wedge at both bolt holes and add this amount to the above numbers. Remember that the measured cross section will be different at each hole in the wedge.

NOTES: 1) Some material may have to be ground off the bottom of the 1-1/4" Morris shank (front face) to get the knife holder to seat down tight against the shank. 2) The 1-1/4" IH shank will fit the NH3 knives, but not the granular knife. 3) All knives come with holes to accommodate 1/2" bolts. If cultivator shanks have 7/16" holes, substitute 7/16" bolts for 1/2" and use a flat washer on the bolt head.

81


FASTENER CHART REFERENCE ///

DESCRIPTION SIZE PART NUMBER

Lock Washer 1/2" 902-LWS-5000

Nut – Grade 5 3/8" 904-NRG-3754

Nut – Grade 5 7/16" 904-NRG-4374

Nut – Grade 5 1/2" 904-NRG-5004

Lock Nut – Stover 1/4" 906-NPT-2505




Lock Nut – Nylon Insert 1/4" 908-NNI-2504

Screw – Pan Head 3/8" 911-SCR-1038

Screw – Self Drill 1/2" 911-SCR-1051

Plow Bolt – O/S Hd Low Shld 3/8" x 1-1/2" 922-POL-1504


Plow Bolt – O/S Hd Low Shld 3/8" x 2" 922-POL-2004

Plow Bolt – O/S Hd 3/8" x 2-1/4" 922-POR-2254



Plow Bolt – O/S Hd 7/16" x 2" 924-POR-2004


Plow Bolt – O/S Hd 7/16"x 2-1/2" 924-POR-2504


Plow Bolt – O/S Hd 7/16" x 3" 924-POR-3004


Plow Bolt 1/2" x 1-3/4" 926-PRG-1754 Legend: O/S Hd = Oversized Head; Low Shld = Low Shoulder; Shld Blt = Shoulder Bolt

Bolt and Nut Part Numbers

Common Torque Values

DESCRIPTION SIZE PART NUMBER

Plow Bolt 1/2" x 2" 926-PRG-2004

Plow Bolt 1/2" x 2-1/4" 926-PRG-2254

Plow Bolt 1/2" x 2-1/2" 926-PRG-2504

Plow Bolt 1/2" x 2-3/4" 926-PRG-2754

Plow Bolt 1/2" x 3" 926-PRG-3004

Plow Bolt 1/2" x 3-1/2" 926-PRG-3504

Hex Bolt – O/S Hd Shld Blt 7/16" x 1-3/4" 933-HOS-1754

Hex Bolt – O/S Hd Shld Blt 7/16" x 2" 933-HOS-2004

Hex Bolt 1/4" x 3/4" 942-HRG-0754

Hex Bolt 1/4" x 2" 942-HRG-2004

Hex Bolt 1/2" x 1-3/4" 946-HRG-1754

Hex Bolt – Grade 8 1/2" x 2" 946-HRG-2005

Hex Bolt – Grade 8 1/2" x 2-1/4" 946-HRG-2255

Hex Bolt – Grade 8 1/2" x 2-1/2" 946-HRG-2505

Hex Bolt 1/2" x 2-3/4" 946-HRG-2754

Hex Bolt 1/2" x 3" 946-HRG-3004

Hex Bolt 1/2" x 3-1/4" 946-HRG-3524

Hex Bolt 1/2" x 3-1/2" 946-HRG-3504

Carriage Bolt – Grade 8 3/8" x 2-1/4" 960-CRG-3755

Carriage Bolt – Grade 8 1/2" x 2" 961-CRG-2005



All highlighted values are common bolt sizes used for BTT products.

This chart lists some of the more common bolt sizes and their calculated torque values. To ensure proper installation and the integrity of the bolts, it is recommended that you follow these values. We have highlighted some of the more common sizes that our products will use.

USS/SAE Grade 8BOLT DIAMETER WRENCH SIZE TORQUE DRY FT. LBS. LUBRICATED FT. LBS.

1/4" 7/16" 12 9

5/16" 1/2" 24 18

3/8" 9/16" 45 35

7/16" 5/8" 70 50

1/2" 3/4" 110 80

9/16" 13/16" 150 110

5/8" 15/16" 210 160

3/4" 1-1/8" 380 280

7/8" 1-5/16" 600 450

1" 1-1/2" 910 680

82

tillagetools.com

DEALERS

ALBERTA

ATHABASCA, ABDEERLAND (780) 675-2256

BALZAC, ABROCKY MOUNTAIN EQUIPMENT (403) 513-7000

BARRHEAD, ABMARTIN DEERLINE (780) 674-2213

BEAVERLODGE, ABFOSTER’S AGRI-WORLD (780) 354-3622

BOW ISLAND, ABROCKY MOUNTAIN EQUIPMENT (403) 545-6844

BROOKS, ABBROOKS FARM CENTRE (403) 362-8222

CAMROSE, ABSELMAC EQUIPMENT (780) 672-2452

CORONATION, ABFUTURE AG INC. (403) 578-3747

DRUMHELLER, ABROCKY MOUNTAIN EQUIPMENT (403) 823-2626

FALHER, ABROCKY MOUNTAIN EQUIPMENT (780) 837-4691

FORT SASKATCHEWAN, ABDEERLAND (780) 998-3249

GRANDE PRAIRIE, ABDOUGLAS LAKE EQUIPMENT (780) 532-5344

BLUE WAVE ENERGY (780) 814-6111

GRIMSHAW, ABROCKY MOUNTAIN EQUIPMENT (780) 332-4691

HIGH PRAIRIE, ABMARTIN DEERLINE (780) 526-4431

HIGH RIVER, ABROCKY MOUNTAIN EQUIPMENT (403) 652-7944

LA CRETE, ABPRAIRIE COAST EQUIPMENT (780) 928-3337

LETHBRIDGE, ABROCKY MOUNTAIN EQUIPMENT (403) 327-3154

MEDICINE HAT, ABROCKY MOUNTAIN EQUIPMENT (403) 528-3838

MILK RIVER, ABROCKY MOUNTAIN EQUIPMENT (403) 647-3828

OLDS, ABFUTURE AG INC. (403) 556-6711

OYEN, ABROCKY MOUNTAIN EQUIPMENT (403) 664-3730

PICTURE BUTTE, ABROCKY MOUNTAIN EQUIPMENT (403) 732-5658

PONOKA, ABTOWN & COUNTRY SUPPLIES (780) 783-5555

RED DEER, ABFUTURE AG INC. (403) 343-6101

RIMBEY, ABFUTURE AG INC. (403) 843-2205

ROCKYFORD, ABK. PEDERSEN EQUIPMENT LTD. (403) 533-3757

SEDALIA, ABSEDALIA CONSUMERS CO-OP (403) 326-2152

SPIRIT RIVER, ABDAVE ROSS EQUIPMENT (780) 864-3731

ST. PAUL, ABTRI-AG IMPLEMENTS (780) 645-4465

STETTLER, ABFUTURE AG INC. (403) 742-3740

STONEY PLAIN, ABSELMAC EQUIPMENT (780) 963-2251

TABER, ABROCKY MOUNTAIN EQUIPMENT (403) 223-2333

THORSBY, ABTHORSBY FARM CENTRE (780) 789-3989

TROCHU, ABCERVUS EQUIPMENT (403) 442-3982

VEGREVILLE, ABROCKY MOUNTAIN EQUIPMENT (866) 632-6677

VERMILION, ABIRELAND FARM EQUIPMENT LTD. (780) 853-6344

VULCAN, ABARMAN EQUIPMENT SALES INC. (403) 485-6968

WAINWRIGHT, ABTRI-AG IMPLEMENTS (780) 842-4408

WASKATENAU, ABWASKATENAU MOTORS (780) 358-2287

WESTLOCK, ABMARTIN DEERLINE (780) 349-3391

ROCKY MOUNTAIN EQUIPMENT (780) 349-3720

BRITISH COLUMBIA

DAWSON CREEK, BCDOUGLAS LAKE EQUIPMENT (250) 782-5281

ROLLA, BCROLLA AGRICULTURE SERVICES (250) 759-4770

MANITOBA

ALTONA, MBGREEN VALLEY EQUIPMENT INC. (204) 324-6456

ARBORG, MBSHACHTAY SALES & SERVICE (204) 376-5233

BOISSEVAIN, MBROCKY MOUNTAIN EQUIPMENT (204) 534-2463

BRANDON, MBROCKY MOUNTAIN EQUIPMENT (204) 725-2273

CARMAN, MBGREENLAND EQUIPMENT LTD. (204) 745-2054

DAUPHIN, MBREIT-SYD FARM EQUIPMENT (204) 638-6443

ELIE, MBCHABOT IMPLEMENTS CO. (204) 353-2392

KILLARNEY, MBGREEN VALLEY EQUIPMENT INC. (204) 523-7571

ROCKY MOUNTAIN EQUIPMENT (204) 523-4644

MANITOU, MBA.R.K. NEW-TECH LTD. (204) 242-2424

MELITA, MBD.B. MURRAY LTD.(800) 805-0495

MORDEN, MBGREEN VALLEY EQUIPMENT INC. (204) 325-7742

NEEPAWA, MBMAZERGROUP – NEEPAWA (204) 476-2364

CHABOT IMPLEMENTS CO. (204) 476-3333

PORTAGE LA PRAIRIE, MBCHABOT IMPLEMENTS CO. (204) 857-9397

ROSENORT, MBROSENORT MOTORS (1979) LTD. (204) 746-8441

RUSSELL, MBROCKY MOUNTAIN EQUIPMENT (204) 773-2644

SHOAL LAKE, MBROCKY MOUNTAIN EQUIPMENT (204) 759-2626

STEINBACH, MBSOUTHEASTERN FARM EQUIP. LTD. (204) 326-9834

CHABOT IMPLEMENTS CO. (204) 326-6417

SWAN RIVER, MBMAZERGROUP – SWAN RIVER (204) 734-9362

TREHERNE, MBGREENVALLEY EQUIPMENT INC. (204) 723-2546

WINNIPEG, MBLEO’S SALES & SERVICE LTD. (204) 694-4978

SASKATCHEWAN

ARCHERWILL, SKARCHERWILL CO-OP (306) 323-2112

ASSINIBOIA, SKE. BOURASSA & SONS LTD. (306) 642-3826

AVONLEA, SKNELSON MOTORS & EQUIP. (1976) (306) 868-2022

BALCARRES, SKMAPLE FARM EQUIPMENT (306) 334-2492

CARROT RIVER, SKCARROT RIVER IMPLEMENTS (306) 768-2715

CHAMBERLAIN, SKSCHROEDER BROS. IMPL. LTD. (306) 638-6305

CHOICELAND, SKPINELAND CO-OP (306) 428-2175

DAVIDSON, SKYOUNG’S EQUIPMENT (306) 567-3074

DINSMORE, SKT.J. SERVICE LTD. (306) 846-2152

ELROSE, SKWESTERN SALES INC. (306) 378-2575

ESTEVAN, SKNELSON MOTORS & EQUIP. (1976) (306) 634-6422

REDHEAD EQUIPMENT LTD. (306) 634-4788

FOAM LAKE, SKMAPLE FARM EQUIPMENT (306) 272-3345

FRONTIER, SKPIONEER CO-OPERATIVE (306) 296-2233

GRAVELBOURG, SKL&L AUTO & AG SUPPLIES (306) 648-3622

HUMBOLDT, SKHERGOTT FARM EQUIPMENT LTD. (306) 682-2591

KAMSACK, SKNYKOLAISHEN FARM EQUIP. LTD. (306) 542-2411

KINDERSLEY, SKKRAMER LTD. (306) 463-3797

KINISTINO, SKAG WORLD EQUIPMENT (306) 864-2200

FARM WORLD EQUIPMENT LTD. (306) 864-3667

LEADER, SKJAY DEE AGTECH (306) 628-3899

LLOYDMINSTER, SKMOODY’S EQUIPMENT (306) 825-6141

MEADOW LAKE, SKLAZAR EQUIPMENT (306) 236-5222

MOOSE JAW, SKYOUNG’S EQUIPMENT (306) 694-1800

MOOSOMIN, SKROCKY MOUNTAIN EQUIPMENT (306) 435-3866

NAICAM, SKCROPPER MOTORS (306) 874-2011

NORTH BATTLEFORD, SKKRAMER LTD. (306) 445-6151

OUTLOOK, SKWESTERN SALES INC. (306) 867-8601

JOHN BOB FARM EQUIPMENT LTD. (306) 867-9544

PARADISE HILL, SKNOVLAN BROTHERS (306) 344-2029

PERDUE, SKMOODY’S EQUIPMENT (306) 237-4272

PONTEIX, SKTHIBAULT’S AUTO PARTS PLUS (306) 625-3355

PORCUPINE PLAIN, SKPARKLAND CO-OP (306) 278-2191

PREECEVILLE, SKMAPLE FARM EQUIPMENT (306) 547-2007

PRINCE ALBERT, SKFARM WORLD EQUIPMENT LTD. (306) 922-2525

RADVILLE, SKE. BOURASSA & SONS LTD. (306) 869-2277

RAYMORE, SKYOUNG’S EQUIPMENT (306) 746-2288

REDVERS, SKNELSON MOTORS & EQUIP. (1976) (306) 452-3418

REGINA, SKYOUNG’S EQUIPMENT (306) 565-2405

ROSETOWN, SKWESTERN SALES INC. (306) 882-4291

SASKATOON, SKMOODY’S EQUIPMENT (306) 934-4686

SHAUNAVON, SKSHAUNAVON IND. (1980) LTD. (306) 297-2630

SPIRITWOOD, SKMARTODAM MOTORS (1983) LTD. (306) 883-2045

ST. BRIEUX, SKCOQUET & BOURGAULT IMPLTS (306) 275-2050

SWIFT CURRENT, SKREDHEAD EQUIPMENT LTD. (306) 773-2951

TISDALE, SKJOHN BOB FARM EQUIPMENT LTD. (306) 873-4588

UNITY, SKMOODY’S EQUIPMENT (306) 228-2686

WADENA, SKWHEATBELT SALES (306) 338-2588

WATROUS, SKA & S EQUIP. WATROUS (1978) LTD. (306) 946-3387

WEYBURN, SKYOUNG’S EQUIPMENT (306) 842-2629

WINDTHORST, SKYOUNG’S EQUIPMENT (306) 224-2110

WYNYARD, SKMAPLE FARM EQUIPMENT (306) 554-2536

YORKTON, SKMAPLE FARM EQUIPMENT (306) 783-9459

COLORADO

STERLING, COPRO-TILL (970) 466-0721

IDAHO

BOISE, IDWESTERN STATES EQUIPMENT CO. (208) 888-2287

IDAHO FALLS, IDWESTERN STATES EQUIPMENT CO. (208) 552-3400

POCATELLO, IDWESTERN STATES EQUIPMENT CO. (208) 232-2640

TWIN FALLS, IDWESTERN STATES EQUIPMENT CO. (208) 734-7330

ILLINOIS

TAYLORVILLE, ILKUHNS EQUIPMENT COMPANY (217) 824-8146

KANSAS

GRAINFIELD, KSSHAW MOTOR CO. (785) 673-4228

TOPEKA, KSINTERSTATE FARM PRODUCTS (785) 233-0869

KALVESTA, KSKALVESTA IMPLEMENTS CO. (620) 855-3567

MINNESOTA

ADA, MNTITAN MACHINARY (218) 784-2321

ADAMS, MNFARM TECH (GPS SERVICES) (507) 582-1477

CROOKSTON, MNCROOKSTON IMPLEMENTS CO. (218) 281-3683

EAST GRAND FORKS, MNAG PRO TECH (218) 779-1993

ELBOW LAKE, MNTITAN MACHINERY (218) 685-4467

FRANKLIN, MNFRANKLIN VALLEY SALES (507) 829-8909

HILLS, MNDAVE’S REPAIR (507) 962-3631

ROSEAU, MNTITAN MACHINERY (218) 463-1781

THIEF RIVER FALLS, MNNELSON EQUIPMENT (218) 681-1997

TITAN MACHINERY (218) 681-1423

MISSOURI

MEXICO, MOSYDENSTRICKER IMPLEMENT CO. (573) 581-5900

TIPTON, MOSYDENSTRICKER IMPLEMENT CO. (660) 433-5596

MONTANA

BILLINGS, MTTORGERSON’S LLC (406) 252-8614

BLACK EAGLE, MTFRIELING’S AG EQUIP (406) 453-2924

CHINOOK, MTRAINBOW IRRIGATION (406) 357-2211

CIRCLE, MTFARM EQUIPMENT SALES (406) 485-2145

CONRAD, MTFRONTLINE AG (406) 278-5531

CULBERTSON, MTFARM EQUIPMENT SALES INC. (406) 787-6201

CUT BANK, MTFRONTLINE AG (406) 873-5505

ETHRIDGE, MTTORGERSON’S LLC (406) 339-2222

GLASGOW, MTFARM EQUIPMENT SALES INC. (406) 228-2496

GREAT FALLS, MTHOVEN EQUIPMENT COMPANY (406) 727-7153

TORGERSON’S LLC (406) 453-1453

HAVRE, MTTILLEMAN MOTOR CO. (406) 265-7865

TORGERSON’S LLC (406) 265-5887

LEWISTOWN, MTTORGERSON’S LLC 406-538-8795

PLENTYWOOD, MTFARM EQUIPMENT SALES INC. (406) 765-1531

SIDNEY, MTSUNRISE EQUIPMENT (406) 488-3112

83


REFERENCE ///

NORTH DAKOTA

BEACH, NDWEST PLAINS INC. (701) 872-4154

BOWMAN, NDWEST PLAINS INC. (701) 523-3296

CALVIN, NDFARMER’S UNION OIL COMPANY (701) 697-5208

CARRINGTON, NDERICKSON IMPLEMENT INC. (701) 652-2821

CASSELTON, NDTITAN MACHINERY (701) 347-4671

DEVIL’S LAKE, NDHIGH PLAINS EQUIPMENT (701) 662-7522

LEADING EDGE EQUIPMENT (701) 662-4948

DICKINSON, NDDAKOTA FARM EQUIPMENT INC. (701) 225-8123

WEST PLAINS INC. (701) 483-8741

HETTINGER, NDWEST PLAINS INC. (701) 567-4505

HOOPLE, NDBUTLER MACHINERY (701) 894-6363

JAMESTOWN, NDTITAN MACHINERY (701) 252-8200

KULM, NDTITAN MACHINERY (701) 647-2442

LANGDON, NDSIMPLOT SOILBUILDERS (701) 256-2815

LISBON, NDBERUBES INC. (701) 683-4195

MANDAN, NDNORTHERN PLAINS EQUIPMENT (701) 663-9864

MINOT, NDFARMER’S UNION OIL COMPANY (ENERBASE) (701) 825-2501

MOHALL, NDGREEN AG SERVICES (701) 756-6050

ROLETTE, NDFARMER’S UNION OIL COMPANY (701) 246-3493

SAWYER, NDHAUSER’S FARM SUPPLY (701) 624-5310

STANLEY, NDSTANLEY EQUIPMENT (701) 628-2950

VALLEY CITY, NDA P EQUIPMENT (701) 845-2143

WAHPETON, NDTITAN MACHINERY (701) 642-8424

WASHBURN, NDR D O EQUIPMENT (701) 462-3284

WILLISTON, NDBOLDT FARM SUPPLY (701) 774-3739

FRONTIER EQUIPMENT (701) 774-0957

NEBRASKA

KIMBALL, NEBRIGHTON EQUIPMENT (308) 235-3683

SCOTT BLUFF, NEFRANK IMPLEMENT CO. (308) 632-4440

OKLAHOMA

ENID, OKENID NEW HOLLAND (580) 234-2668

OREGON

PENDLETON, ORWESTERN STATES EQUIPMENT CO. (541) 276-5812

SOUTH DAKOTA

ONIDA, SDLAMB’S CHEVROLET & IMPLEMENT (605) 258-2661

REDFIELD, SDTITAN MACHINERY (605) 472-0810

TEXAS

WINTERS, TXMILTON’S HARDWARE & AUTO SUPPLY (325) 754-4578

WASHINGTON

PASCO, WAWESTERN STATES EQUIPMENT CO. (509) 547-9541

ROSALIA, WAJERRY’S FARM SUPPLY (509) 523-3276

SPOKANE, WASPRAY CENTER ELECTRONICS INC. (509) 838-2209

WESTERN STATES EQUIPMENT CO. (509) 535-1744

WYOMING

CHEYENNE, WY4 RIVERS EQUIPMENT (307) 638-8669

EUROPEAN DISTRIBUTORSIndustriehof GmbHIm Winkel 5 D-30900 Wedemark Germany Phone: +49 (0) 5130-6072-0www.industriehof.com

Martin Lishman Ltd. Unit 2B, Roman Bank, Bourne, Lincs PE10 9LQ UK Phone: +44 (0) 1778 426600 www.martinlishman.com

UNITED STATES DISTRIBUTORUS Manufacturing Inc.1707 21st Street Eldora, IA 50627 Toll-free: 800-800-1812 Fax: 641-939-7539

AUSTRALIAN DISTRIBUTORSBourgault Industries16 Eliot Road Armadale, WA 6112 Australia Phone: 08 9399 9700

NEW SOUTH WALES

COLEAMBALLYHUTCHEON A & G 02 6954 4280

CONDOBOLINHUTCHEON & PEARCE 02 6895 2666

COONAMBLECHESTERFIELD AUSTRALIA 02 6822 5111

COROWAO’CONNORS 02 6033 1666

COWRAHUTCHEON & PEARCE 02 6341 4800

DUBBOCHESTERFIELD AUSTRALIA 02 6885 3300

FORBESMCCLINTOCK & CO. 02 6852 1200

GRENFELLMCCLINTOCK & CO. 02 6343 1422

GRIFFITHA & G MACHINERY 02 6964 3422

LAKE CARGELLIGOA & G MACHINERY 02 6898 1305

MOREESUSTAIN AG 02 6752 1622

NARRANDERAHUTCHEON A & G 02 6959 1522

PARKESHUTCHEON & PEARCE 02 6862 1666

TEMORAHUTCHEON & PEARCE 02 6977 1100

WAGGA WAGGAHUTCHEON & PEARCE 02 6933 7900

WARRENCHESTERFIELD AUSTRALIA 02 6847 3522

WELLINGTONCHESTERFIELD AUSTRALIA 02 6845 1666

WYALONGWYALONG MACHINERY & ENGINEERING 02 6972-4555

SOUTH AUSTRALIA

BORDERTOWNO’CONNORS 08 8752 1311

CEDUNACEDUNA MACHINERY 08 8625 2999

CLAREWSB DISTRIBUTORS 08 8842 2177

CLEVEPRINGLES AG PLUS CROUCH RURAL 08 8628 2150

CRYSTAL BROOKPRINGLES AG PLUS CROUCH RURAL 08 8636 2257

CUMMINSPRINGLES AG PLUS CROUCH RURAL 08 8676 2105

KADINAMEASEDAY'S SERVICES 08 8828-0200

KIMBAPRINGLES AG PLUS CROUCH RURAL 08 8627 2071

LYNDOCHLYNDOCH MOTORS 08 8524 4140

MAITLANDEGLINTON BROS. 08 8832 2277

MURRAY BRIDGERAMSEY BROS. 08 8531 2244

PARINGAHOODS AGRIMOTIVE 08 8595 5388

PINNAROOPARK MOTORS 08 8577 8141

WUDINNAPRINGLES AG PLUS CROUCH RURAL 08 8680 2236

VICTORIA

BIRCHIPO'CONNORS 03 5492 2311

DELACOMBEWESTAG 03 5335 8609

HORSHAMO'CONNORS 03 5382 1727

MILDURAHAEUSLER FARM SUPPLIES 03 5055 0600

SEA LAKEHAEUSLER FARM SUPPLIES 03 5070 3400

SHEPPARTONO’CONNORS 03 5821 4555

SWAN HILLSUNRISE AG 03 5032-0099

WARRACKNABEALO'CONNORS 03 5398 1877

WESTERN AUSTRALIA

ALBANYRATTEN & SLATER 08 9842 8529

BOYUP BROOKGREENLINE AG 08 9765 1305

CARNAMAHAFGRI EQUIPMENT 08 9951 1130

CUNDERDINAG IMPLEMENTS 08 9635 1364

DALWALLINUJOLLY & SONS 08 9661 1105

ESPERANCEPH KERR & CO. 08 9071 3711

GERALDTONAFGRI EQUIPMENT 08 9921 5044

GNOWANGERUPRATTEN & SLATER 08 9827 1207

GUILDFORDGREENLINE AG 08 9478 5099

LAKE GRACEGREENLINE AG 08 9865 1100

MERREDINAG IMPLEMENTS 08 9041 4100

MOORAAFGRI EQUIPMENT 08 9651-1363

MUKINBUDINAG IMPLEMENTS 08 9047 1109

NAREMBEENAG IMPLEMENTS 08 9064 7214

NARROGINGREENLINE AG 08 9881 4250

NORTHAMAG IMPLEMENTS 08 9622 5855

PINGELLYGREENLINE AG 08 9887 1395

SOUTHERN CROSSAG IMPLEMENTS 08 9049 1104

WAGINGREENLINE AG 08 9861-0000

WONGAN HILLSJOLLY & SONS 08 9671 1311

WYALKATCHEMJOLLY & SONS 08 9681-1477

AUSTRALIAN DEALERS

tillagetools.com

84

Cornelius ChomenchukAssistant Sales Manager/ Manitoba Territory Manager

Roger SchiermanAlberta Territory Manager

Len HorvathService and Warranty Manager

Penny UlledalSales Coordinator

Kelly StevensonSaskatchewan Territory Manager

Dean BigelowR&D Manager

Tom ClementsNorth & South Dakota, Montana, Minnesota Territory Manager

Patrick YeagerManaging Director of Sales and Marketing

Tim BodvarsonMarketing Manager

CONTACT US

P.O. Box 310, 200 – 5th Avenue South St. Brieux, SK, Canada S0K 3V0

P: 1.800.878.7714F: 1.306.275.4720E: [email protected]

www.tillagetools.com

/tillagetools @TillageTools

tillagetools.com


F. P. Bourgault Tillage Tools Ltd.P.O. Box 310, 200 – 5th Avenue South

St. Brieux, SK, Canada S0K 3V0

P: 1.800.878.7714 | F: 1.306.275.4720www.tillagetools.com

tillage & seeding tools - ag world equipment | farm...

Documents