this signs is rated at 150 mph when mounted to columns rev e … · 2019. 11. 18. · 4. install...
TRANSCRIPT
DETAIL A
DETAIL E
A
E
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
InstallationADO/ADLO Signs
WHP 9/13/2017241-0357
1 9
EADO or ADLO Style Sign Installation InstructionsCompleted Installation
Enlarged Column Connection Detail
Front View
Rear View
This signs is rated at 150 mph when mounted to columnsat factory manufactured mounting locations. Mountingsigns to columns in any other configuration can affectthe integrity of the sign. ADO Signs weigh approximately2.2 lbs/ft². ADLO Signs weigh 3.2 lbs/ft²
Max sign height: 5 ft
(4) 3/8 Bolts attachbrackets to sign.Supplied by Nevco.
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
ADO/ADLO Sign Installation Step One
Mount a bracket for each mounting pointon sign as shown with Nevco supplied 3/8-16 bolts.
InstallationADO/ADLO Signs
WHP241-0357
2 9
Mount Nevco provided angle brackets to sign.
When attaching brackets, leaving the bottom bracketloose can allow for tolerances in mating bracket placementon the steel columns.
E
9/13/2017
Fasten multi-section signstogether using suppliedscrews taped to male plicedivider. (ADLO signs willrequire the face to be slideaway from the splice joint)
Mounting Bracket Detail
SCALE 1 / 2
Top Bracket
on column
DETAIL K
SCALE 1 / 2
K
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
ADO Sign Installation Step TwoMount column brackets on column as shown.Mounting bracket layout front view.
WHP241-0357
3 9
Brackets mounted on sign not shownfor clarity.
Bottom BracketTop edge (for welding)(Sign Height) - 2⅛"
Bottom BracketCenter of holes(Sign Height) - 1⅛"
If welding the brackets to the column. Nevco recommends mounting only the top two brackets on the columns and bolting the bottom two brackets on the sign. This way they can be clamped and welded wherever they fall.
If bolting to columns drill 716"
diameter holes. Use 38" boltsminimum, supplied by others
7/16 in
1 1/4 in6 in
1/4 in
2 in
InstallationADO/ADLO Signs
Note: If sign is mounted with scoreboard installed on laterals, the sign also requires the same sized laterals. See scoreboard lateral installation for lateral details.
E
9/13/2017
1 1/4 in
3 5/16 in2 1/4 in
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
Mounting bracket layout side view.The 2 1/2" spacing from the columnis nominal. Slotted holes in the brackets allow for 1" total adjustment
ADO Sign Installation Step Two Cont.
InstallationADO/ADLO Signs
WHP241-0357
4 9
Stee
l Col
um
n
AD
O/A
DLO
Sig
n
2 1/2 in
Install supplied catchbolt and nut in sign bracket without a washerto aid in sign installation.
Catch nut drops intomating bracket pocket
E
9/13/2017
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
Installing ADO Signs onto Laterals
1. Assemble horizontal sign sections with supplied #8 sheet metal screws
2. Install eye bolts for lifting cabinet into place.
4. Install sign by bolting or weldingbracket to lateral.
Lateral
3. Install brackets to signs using (4) ea. 38x11
4" serrated flange bolts, supplied byNevco. Note orientation of brackets according to bracket orientationlabels on the back of the sign cabinets.The bottom bracket can be left looseto accomodate adjustment for lateral placement.
5 9 241-0357
InstallationADO/ADLO Signs
WHP
E
9/13/2017
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
InstallationADO/ADLO Signs
WHP 9/13/2017 6 9
241-0357
Message Center
Sign
Option 1: Tube and angleSpecial case of sign mounted next to message center.
ADO/ADLO Sign Installation Step Two Cont.Sign Back
Message Center BackAngle provided by others.
Angle or tube steel provided by others.
Extend angle and laterals used to mountmessage center to end of sign and mountsign to angle with 3/8-16 bolts. Signs next to message centers do not usethe 12" slotted angle brackets used for signs that are mounted to column.
Drill for and boltsign to 6x6 anglewith 3/8 boltssupplied by Nevco. (1) 3/8 bolt required for each sign mountinglocation on top lateraland (1) 3/8 bolt requiredfor each sign mounting locationon bottom lateral.
Bolt or weld brackets to column(Column not shown for clarity)
(1/8)
6"
1/4 6"
Weld angle bracket
to 6x6 angle, or bolt
using (4) 3/8"x1 1/4"
when cabinet rivnuts
align with bracket
location.
6x6 AngleSupplied by others
Option 2: 6x6 Angle2x2 Angle provided by others. Message
Center Back
Extend angle used to mountmessage center to end of signand mount sign to angle with3/8-16 bolts.
12" slotted angle bracketmounted to column.
Max distance of 4' fromedge of sign to last bracket
E
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
ADO/ADLO Sign Installation Step ThreeLift sign to mounted brackets securing sign to brackets with Nevco provided 3/8-16 bolts. 2 each connection.See Sheet 1 for finished installation view.
InstallationADO/ADLO Signs
WHP241-0357
7 9
Lifting angle relative to signtop must be greater than 45°.
It is recommended to use a spreader barduring sign lift.
E
9/13/2017
A
(Sign
Width)
B
(Bracket
Spacing)
C
(Distance
from End)
Qty. of
Bracket
Sets
36' 10' 3' 4
32' 8' 4' 4
30' 8' 3' 4
28' 10' 4' 3
24' 8' 4' 3
18' 10' 4' 2
16' 8' 4' 2
12' 8' 2' 2
10' 8' 1' 2
8' 6' 1' 2
7' 5' 1' 2
6' 2' 2' 2
5' 3' 1' 2
4' 2' 1' 2
< 4' - Center 1
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
WHP 9/13/2017241-0357
8 9
EB (Bracket Spacing)
A (Sign Width)
C (Distance from End)
Notes: 1. Building signs of widths listed above using the bracket layouts listed above will allow the sign to be attached directly to the supporting columns For sign widths that are not listed above, the bracket spacing would depend on the sign construction. Nevco does not exceed 10' spacing and 4' from the end. 2. This bracket is designed to exceed150MPH basic design wind speed, 50' in the air, with a display weighing 13 lbs/sq-ft, at a maximum of 22 sq-ft per bracket 3. A bracket set consists of a top and bottom bracket, bolts to attach it to the sign brackets that attach to the column and the bolts that mate the brackets together
Bolts to Sign
2 1/4 in1/4 in
2 1/4 in1/4 in
15/16 in
12 in2 3/4 in
1 in 25/32 in
2 in
InstallationADO/ADLO Signs
Part
Number
Sign
Width x Height
A
(Distance from
bottom)
B
(Distance from
bottom)
870-0071 8 x 2 11.38 in - - -
870-0109 8 x 3 23.38 in - - -
870-0035 10 x 2 9.15 in - - -
870-0098 10 x 3 14.25 in - - -
870-0096 12 x 3 18.35 in - - -
870-0081 14 x 4 28.13 in - - -
870-0029 16 x 2 15.75 in - - -
870-0048 16 x 3 23.50 in - - -
870-0093 16 x 3 27.50 in - - -
870-0173 16 x 4 31.81 in - - -
870-0022 18 x 2 15.75 in - - -
870-0018 18 x 3 21.75 in - - -
870-0015 18 x 5 39.00 in - - -
870-0136 22.05 x 3 10.375 in 32.28 in
870-0086 24 x 2 13.78 in 19.66 in
870-0003 24 x 3 18.75 in 31.75 in
870-0038 24 x 4 30.85 in 43.85 in
870-0043 28 x 3 17.75 in 30.85 in
870-0068 32 x 4 23.00 in 41.34 in
870-0064 36 x 3 11.35 in 30.39 in
870-0032 36 x 4 21.50 in 42.00 in
870-0101 40 x 4 26.80 in 33.80 in
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
ADO Arch SignInstallation Print
WHP 9/13/2017241-0357
9 9
Sign Width
Sign Height
2 1/4 in(Top of bracket from
bottom of sign)
Dimension "A" Dimension "B"*If necessary
Notes: 1. Dimension "A" and "B" are from bottom of sign to face of mounting bracket 2. Mounting brackets have 1/4" play up/down each way 2. *Dimension "B" is only applicable on larger signs with an additional mounting location
E