solar|thermodynamics

solar panelthermodynamic

hot water

swimming pools’ temperature control

heating

cooling

The solar panel acts as evaporator within the thermodynamic cycle of vapor-compression heat pump.

Inside the panel, there is an environmentally friendly refrigerant at low temperature (even below 0ºC). The panel absorbs the heat from the environment and raises the temperature of the refrigerant which is pressurized and circulated through the system by a compressor.

Next words, the refrigerant is circulated through a condenser which transfers the heat to the water in the tank.

Other elements of the thermodynamic group are the expansion valve, etc.

Solar thermodynamics panels operate all day and any season.

MaterialSuperficial absorving finishTotal collector areaDimensionsEmpty weightIn/out pipes cross-sectionIn/out pipes material

THERMODYNAMIC PANEL Technical features

Aluminium Selective black

3,6m2

1950 x 920 x 20mm7,6kg5/16”

Copper aluminium

Panels have a lain surface for easing the architectural integration.

Additionally panels can be painted in several colors.

solar |thermodynamics

116

solar |thermodynamics

bioenergythermodynamicsystem

a newcompact solar

equipment concept

Bioenergy’s innovative heater is based on a heat pump system that takes advantage of the solar and the environmental energy for an efficient water heating.

This way, consumption is much lower than conventional systems’ one, even reaching an annual average performance 20% higher than other thermal systems in the market.

Description

It is a heat pump-based system that uses a panel as evaporator and/or an indoor heat exchanger for absorbing the solar and the environmental energy achieving a global performance increase.

A heat exchanger, called a condenser, transmits the absorbed energy to the water by means of an environmentally friendly refrigerant (R134a). Moreover there is no direct contact between the refrigerant cycle and the water thus avoiding contamination in case of leakage.

Bioenergy thermodynamic system’s COP goes from 2.5 to 5.5.

Available in 200, 300 and 500l.

117

118

fotovoltaica | bipv

Outdoor thermodynamic panel: it takes advantage of solar radiation increasing performance.

1. Compressor2. Condenser3. Boicer4. Deshidratador5. Expansion value6. Resistance7. Deposit

COMPONENTS

TD-E

ser

ies

TECHNICAL DATA

Acumulation volume (l)

Evaporator

Power supply

Thermal capacity (W)

Consumed power (W)

Antilegionella and emergency resistance

Tannk material accumulator

Isolation

External cover

Dimensions (mm)

200

Thermodynamic panel (1960 x 920 x 20 mm)

230 / 1 Phase / 50 Hz

2500 - 1500 W

500 W

2000 W

Stainless steel

Injected polyurethane 40 Kg/m

White lacquered steel

1350 x 575 x 590

D4TDE200 D4TDE300

Complies with theHE4 “Minimum

solar contribution”of CTE

HOTWATER

WATER SYSTEM

TD-E SERIES

300

Thermodynamic panel (1960 x 920 x 20 mm)

230 / 1 Phase / 50 Hz

2500 - 1500 W

500 W

2000 W

Stainless steel

Injected polyurethane 40 Kg/m

White lacquered steel

1920 x 575 x 590

solar |thermodynamics

1. Compressor2. Condenser3. Deshidratador4. Expansion value5. Deposit6. Fan7. Evaporator

119

fotovoltaica | bipv

Indoor thermodynamic panel: for those locations where it is not possible to install a panel outdoor. The evaporator takes advantage of environment energy for water heating.

COMPONENTS

TD-I

ser

ies

TECHNICAL DATA

Acumulation volume (l) Evaporator Power supply Thermal capacity (W) Consumed power (W) Antilegionella and emergency resistance Tannk material accumulator Isolation External cover Dimensions (mm)

200Internal exchanger with fan230 / 1 Phase / 50 Hz2500 - 1500 W500 W2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1350 x 575 x 590

D4TDE200 D4TDE300

300Internal exchanger with fan230 / 1 Phase / 50 Hz2500 - 1500 W500 W2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1920 x 575 x 590

HOTWATER

WATERSYSTEM

inner air

TD-I SERIES

solar |thermodynamics

1. Compressor2. Condenser3. Boicer4. Deshidratador5. Expansion value6. Deposit7. Fan8. Evaporator

120

fotovoltaica | bipv

It combines both series’ advantages in a single equipment that consists of an outdoor panel for solar radiation and an indoor heat exchanger. The latest will operate during unfavorable external conditions.

COMPONENTS

TD-E

I ser

ies

TECHNICAL DATA

Acumulation volume (l) Evaporator Power supply Thermal capacity (W) Consumed power (W) Antilegionella and emergency resistance Tannk material accumulator Isolation External cover Dimensions (mm)

200Thermodynamic panel +exchanger INT. C/V 230 / 1 Phase / 50 Hz2500 - 1500 W500 W2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1350 x 575 x 590

D4TDE200 D4TDE300

300Thermodynamic panel +exchanger INT. C/V 230 / 1 Phase / 50 Hz2500 - 1500 W500 W2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1920 x 575 x 590

HOTWATER

WATERSYSTEM

inner air

TD-EI SERIES

solar |thermodynamics

121

fotovoltaica | bipv

Outdoor thermodynamic panel: it takes advantage of solar radiation increasing performace.

EI-5

00 s

erie

s

TECHNICAL DATA

Acumulation volume (l) Evaporator 1Evaporator 2 Power supply Thermal capacity (W) Consumed power (W) Antilegionella and emergency resistance Tannk material accumulator Isolation External cover Dimensions (mm)

500Thermodynamic panel (1960 x 920 x 20 mm)Internal exchanger with fan230 / 1 Phase / 50 Hz5000 - 3000 W1000 W2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel2000 x 595 x 710

D5TDEI500

solar |thermodynamics

inner air

HOTWATER

WATER SYSTEM

TD-500 SERIES

122

fotovoltaica | bipv

TDF series is a compact solution of a solar thermal system with a thermodynamic support within.

Freedom to choose the thermal panel model.

Easy to install: all connections are hydraulic hence no specialist is required. The installation can be completed by a plumber.

Double solar use: it takes advantage of solar energy directly, using a solar coil, and indirectly to evaporate the heat pump’s refrigerant increasing collector’s performance.

COMPONENTS

TDF

seri

es

TECHNICAL DATA

Acumulation volume (l) Evaporator 1Evaporator 2 Power supply Thermal capacity (W) Consumed power (W) Antilegionella and emergency resistance Tannk material accumulator Isolation External cover Dimensions (mm)

200Thermodynamic solar-exchangerInternal exchanger with fan230 / 1 Phase / 50 Hz2800 - 3800 W500 W (F200/300)2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1350 x 575 x 590

D6TDF200

solar |thermodynamics

HOTWATER

***Weather conditions: Madrid, 2 selective flat plate, catchment area = 4 m

COP annual average=12’74***

inner air

WATER SYSTEM

TD SERIES

300Thermodynamic solar-exchangerInternal exchanger with fan230 / 1 Phase / 50 Hz2800 - 3800 W500 W (F200/300)2000 WStainless steelInjected polyurethane 40 Kg/mGray lacquered steel1920 x 575 x 590

D6TDF300

1. Deposit2. Comprenssor3. Enthalay recovery4. Forced evaporator5. Solar coil6. Condenser7. Expansion value8. Solar pump

9. Thermal panel output10. Input from thermal panel11. Hot water outlet12. Electrical connection13. Water inlet14. Drain

COP 12,74

TD-F series consumes up to a 90% less than

an electric thermo.

Why choosingBioenergy?

solar |thermodynamics

- money + ecology BIOENERGY is an energy saving system for water heating.

No matter weather conditionsHot water is produced under any atmospheric condition. The system works also at night and under windy and/or rainy conditions.Additionally it does not require from an auxiliary system such as traditional solar systems.

The very bestCorrosion-resistant, high quality materials that enlarge installations lifespan and reliability.

Capacity: TD200, TD300 or TD500?TD200 is suitable for families with 2 to 5 members. From 5 to 7 members TD300 is the best solution. TD500 is recommended for families with more than 8 members.

Thermodynamic system Why choosing Bioenergy TD-F?Freedom to choose the thermal panel model. 200, 300 and 500l available models.Maximum use of solar energy.

123

solar |thermodynamics

energyefficiencyfactorThanks to its double solar and thermodynamic working functions, BIOENERGY THERMODYNAMIC SYSTEM can produce more than 12kWh per each kWh supplied. Its thermodynamic technology generates 3.5kWh per each kW consumed which is equivalent to a 1,200% and 350% energy efficiency respectively.

Conversely a conventional electric thermal system reaches a maximum performance of 98% compared to the consumed primary energy.

Any high efficiency boiler can reach a maximum of 95% performance, this is to say, it consumes more energy than generates.

you will reduce up to3 tons of CO2 annually.

TD-E SERIES TD-I SERIES

TD-F SERIES TD-EI SERIES

95%

1200%

350%

98%

1400%

1200%

1000%

800%

600%

400%

200%

0%

TD-F TD-I / TD-E electric thermal Boiler

124

solar |thermodynamics

125

HEA

TIN

G L

AR

GE

VO

LUM

ES O

F W

ATE

R

TECHNICAL FEATURES

Descriptive characteristics:

THERMODYNAMIC GROUP:

It is composed of a high efficiency compressor, a thermostatic expansion valve, a heat exchanger, high-performance and environmentally friendly refrigerant R407C and an electronic controller.

Reversible equipment for heating and cooling installations.

Automatic defrost function.

Protection systems against high/low pressure operation and against freezing, overheating and discharge high temperatures.

Flow switch to protect against variations or stopping the flow of water.

Including forced draft unit for increased performance against low temperatures.

With direct or indirect evaporation!

Direct evaporation characteristics:

The evaporation is performed in thermodynamic panels, made of aluminum with lining absorber.

Indirect evaporative characteristics:

The evaporation is done indirectly through a heat exchanger with the solar circuit.

In this way a stable evaporation temperature is achieved increasing system performance.

Collectors can be flat or evacuated tube ones, both types accomplish with all market standards.

CHOICE OF EQUIPMENT

1. Calculate the energy needs for heating / cooling:Heating power required (kW) = Living space (m2) x Ratio heating (W/m2) x 0.001Cooling power required (kW) = Living space (m2) x Ratio cooling (W/m2) x 0.001

2. Choosing the equipment that generates the heating / cooling power similar or immediately greater than the value obtained.*Heating Ratio according to climate zones and type of home. Heating values of 90W / m; cooling of 80W / m.

MODEL D7TDN4 D7TDN6 D7TDN8 D7TDN12 D7TDN16 D7TDN24 D7TDN32 D7TDN40 Heat power nominal (kW) 7 8,5 13,1 15,8 23,4 32,3 46,2 54,3

Current consumption (A) 7,8 9,1 16,1 19,4 9,93 13,2 18,9 23,86Electrical power nominal (kW) 1,7 2 3,4 4 5,8 7,8 11,3 13,8

Power supply (V/ph/Hz) 230 / 1 / 50 380 / 3 / 50

No. panels (und.) 4 6 8 12 16 24 32 40Number of compressors (und.) 1

Compressor type Piston ScrollWater connection (in/out) (inch) 1

Minimum flow of water into the compressor (l/s) 0,32 0,40 0,63 0,75 1,18 1,54 2,2 2,6

Panel dimensions(length / high / depth) (mm) 1960 / 920 / 20

Module weight (kg) 8.0 Equipment Dimensions (length / high / depth) (mm) 760 / 445 /750 880 / 495 / 750

Collection area (m2) 14,4 21,6 28,8 43,2 57,6 86,4 115,2 144

solar |thermodynamics

126

fotovoltaica | bipvsolar |thermodynamics

THER

MO

DYN

AM

ICPO

OL

EQU

IPM

ENT

Our systems offer the possibility to enjoy the pool all year with low power consumption.The main features are:

· Durability.· Installation Flexibility.· Quiet operation.· Advanced Controller.

The components of the thermodynamic solar heating systems for swimming pool are:

· Thermodynamic Panels· Compact unit, painted steel housing· High efficiency compressor.· high performance ecological

refrigerant, R407c.· Incorporates titanium and PVC plate

heat exchanger.· Systems of protection against high

and low operating pressures, freezing overheating and high discharge temperatures.

· Includes flow switch to protect against variations or stops in the water flow.

· High performance against low temperatures due to the forced draft unit.

TECHNICAL FEATURES

MODELO D8TDP4 D8TDP6 D8TDP8 D8TDP12 D8TDP16 D8TDP24 D8TDP32 D8TDP40Heat power nominal (kW) 8,6 10,8 14,4 17,3 27,4 38,1 55,1 61,8

Current consumption (A) 5,5 7 11,8 13,9 6,7 9,3 12,9 10,4Electrical power nominal (kW) 1,2 1,5 2,4 2,7 3,7 5,2 7,4 10,4

Power supply (V/ph/Hz) 230 / 1 / 50 380 / 3 / 50

No. panels (und.) 4 6 8 12 16 24 32 40Number of compressors (und.) 1

Compressor type Pistón ScrollWater connection (in/out) (inch) 1

Minimum flow of water into the compressor (l/s) 0,32 0,40 0,63 0,75 1,18 1,54 2,2 2,6

Panel dimensions(length / high / depth) (mm) 1960 / 920 / 20

Module weight (kg) 8.0 Equipment Dimensions (length / high / depth) (mm) 760 / 445 / 750 880 / 495 / 750

Collection area (m2) 14,4 21,6 28,8 43,2 57,6 86,4 115,2 144