the voltech handbook of power supplies - power...
TRANSCRIPT
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 1
The Voltech Handbook
of Power Supplies
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 2 www.voltech.com Issue 2
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 3
1 Introduction .....................................................................................5
2 AC Line to DC Power Supplies. .....................................................7
2.1 Circuit Description. .................................................................9
3 Linear DC to DC converters..........................................................16
4 Switched Mode DC to DC Convertors. ........................................18
4.1 Forward Convertors. .............................................................19
4.1.1 Buck Regulator..................................................................20
4.1.2 Single Ended Forward Convertor. ....................................26
4.1.3 Push-Pull Convertor. .........................................................28
4.1.4 Two Transistor Forward Convertor. .................................30
4.1.5 Half Bridge Convertor.......................................................32
4.1.6 Full Bridge Convertor. ......................................................34
4.2 Flyback (Boost) Convertors. .................................................36
4.2.1 Boost Convertor ................................................................36
4.2.2 Discontinuous Flyback......................................................38
4.2.3 Continuous Flyback. .........................................................40
4.3 Resonant Convertors. ............................................................42
4.4 Magnetic Amplifiers. ............................................................46
4.5 PWM Control Circuits. .........................................................50
4.5.1 Voltage Mode. ...................................................................50
4.5.2 Current Mode. ...................................................................53
5 Power Factor Correction. ..............................................................57
6 Inrush Current protection. .............................................................61
7 Summary of Power measurements Required on Power Supplies.65
8 Power Supply Measurements. .......................................................67
8.1 Volts, Amps and Watts..........................................................67
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 4 www.voltech.com Issue 2
8.2 VA and PF.............................................................................70
8.3 Peak Repetitive Current and Current Crest Factor. ..............71
8.4 Peak Inrush Current. .............................................................73
8.5 Losses and Efficiency. ..........................................................76
8.6 Amps Harmonics...................................................................78
8.7 Total Harmonic Distortion (THD) ........................................80
8.8 Line Regulation.....................................................................81
8.9 Load Regulation ....................................................................82
9 Example Power Supply Measurements.........................................83
10 Measurement Instrumentation.......................................................85
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 5
1 Introduction
Power supplies are used to convert electrical power from one form to
another. Inputs and outputs may be at different voltages and either DC
or AC:
Power supplies may be used to improve the voltage tolerances that are
available:
to provide isolation from dangerous voltages:
or to provide immunity from noisy inputs:
5V DC 12V DC
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 6 www.voltech.com Issue 2
This handbook reviews some of the circuits and techniques that are
found in modern power supplies. In section 2, two popular power circuit
''topologies'' are presented along with their waveforms.
Pulse Width Modulation (PWM) circuits are discussed in section 2.3.
Power factor correction and Inrush Current protection are reviewed in
section 2.4 and 2.5.
Modern power supplies are required to operate with high efficiency over
a wide range of input conditions. The harmonic content of the input
current may be limited by specification or international standards. It is
essential to make accurate measurements of the input and output
quantities to ensure the power supply is functioning correctly and/or
verify its design. Power supply measurements are discussed in section 3.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 7
2 AC Line to DC Power Supplies.
The electronic circuits found inside computers, photocopiers, televisions
and many other common goods need low voltage dc power. The ac line
is a convenient source, and power supplies are used to convert power
from the high a.c. line voltage to low voltage dc.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 8 www.voltech.com Issue 2
A typical power supply provides several low voltage d.c. outputs that
are:
• ISOLATED from the a.c. supply
• REGULATED i.e. the outputs change little when
• either the load current or line voltage changes.
• and contain LOW RIPPLE and NOISE.
A simple ac line to dc power supply:
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 9
2.1 Circuit Description.
Transformer T1 steps down the input voltage and isolates the rest of the
circuit from the line.
The diode bridge rectifies the ac output of the transformer into dc.
Current flows through diodes D1 and D4 when the dot end of the
transformer is positive, and through D3 and D2 when the non-dot end is
positive.
The output voltage stays at near the peak of the transformer secondary
voltage:
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 10 www.voltech.com Issue 2
Current will only flow into the capacitor when Vs > Vout. The current is
no longer sinusoidal, but distorted because current only flows near the
voltage peaks.
A similar current is drawn from the ac line.
Even in the simplest ac line to dc power supplies the current waveform
can be heavily distorted.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 11
Transformer, rectifier and capacitor circuit:
Advantages:
Simple, low cost.
Low EMI
Disadvantages:
Poor regulation.
Large output ripple at twice the line frequency.
Applications:
Where only crude d.c. power is required.
Battery chargers.
Electrochemical - e.g. Aluminium smelting
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 12 www.voltech.com Issue 2
Regulation can be improved by controlling the voltage at some point in
the circuit. Examples of these are:
(i) At the input with an auto - transformer.
The output voltage is regulated by changing the effective input voltage,
VS
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 13
(ii) In bridge circuit by using SCR's (Silicon Controlled Rectifiers or
thyristors)
SCR's have to be triggered into a conducting 'ON' state. If the point in
the cycle where this occurs is varied, then the average value of voltage
presented to the capacitor is also changed. This is called phase control.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 14 www.voltech.com Issue 2
(iii) By using a regulated dc to dc convertor. e.g. A Linear Power
Supply
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 15
Linear Power Supply:
Advantages:
Simple, Low cost, Low EMI.
Disadvantages:
Transformer constructed using an iron core will be
Relatively large and heavy.
Large value of C required to reduce output ripple
Linear d.c. to d.c. convertor inefficient.
Applications:
Common <100W where size and weight are not important.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 16 www.voltech.com Issue 2
3 Linear DC to DC converters.
A common and simple form of DC to DC convertor is the series pass
regulator. The effective resistance of the transistor is controlled so as to
maintain a constant output voltage over a range of input and output
conditions.
The control circuit operates by first amplifying the difference between a
sample of the output and a reference voltage. This voltage is then used
to control the effective resistance of the transistor by changing its base
current.
Power is lost in the series pass transistor and dissipated as heat. For a
12V to 5V linear DC to DC convertor rated at 1A the power loss will
be:
( 12V - 5V ) x 1A = 7 Watts
In the above case the efficiency will be:
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 17
Output Power x 100% 5V x 1A x 100% = 42 %
Input Power 12V x 1A
The transistor is operating in its linear region. That is the transistor is
neither fully on nor fully off. Power supplies that use this type of DC to
DC convertor are called linear power supplies.
Advantages:
Low output noise,
Low cost.
No RFI or EMI.
Fast transient response.
Disadvantages:
Poor efficiency, which means unnecessary heat loss.
The output voltage has to be lower than the input voltage,
i.e. it is a step down convertor.
There is no electrical isolation between input and
output.
Applications:
Up to 50W. Local Regulation.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 18 www.voltech.com Issue 2
4 Switched Mode DC to DC Convertors.
The overall size of common electrical and electronic equipment is being
constantly reduced. The large scale integration and improved packaging
of electronic circuits has made this possible. The size of the power
supply is reduced to match.
The waste heat generated by a power supply must now be dissipated
over a smaller area. To avoid large temperature rise the power supply
losses must be reduced.
Power Loss = Input Power - Output Power.
Efficiency = Output Power x 100%
Input Power
This led to the development of switched mode dc. to dc. convertors that
operate at high frequency (>20kHz) with improved size, weight and
efficiency.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 19
Isolation can be built in to a switched mode dc to dc converter, a small
ferrite cored transformer then replacing the large iron cored 50Hz
transformer. Typically then, the line input is rectified directly to produce
a high voltage dc which is the input to an isolated dc to dc convertor.
4.1 Forward Convertors.
The principle of a Forward Convertor is that it chops the input D.C.
voltage and transfers power to the output during the ‘on’ state while
energy is simultaneously stored in an inductor. This stored energy is
used to transfer power to the output during the ‘off’ state.
The buck regulator is a simple example of a non-isolated forward
convertor, and its operation is described in detail below.
The toplogies that follow the buck regulator (4.1.2 - 4.1.6) have the
additional benefit of transformer isolation. In addition, the transformer
turns ratio allows for large differences between the input and output
voltages whilst maintaining reasonable cycle on/off ratios.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 20 www.voltech.com Issue 2
4.1.1 Buck Regulator.
Switched mode DC to DC convertors can overcome all of the linear
regulator disadvantages. They use a power switch to chop the DC input
voltage into AC, which is then filtered to produce a DC output.
The output voltage will be the average value of the AC waveform.
The switch (normally a transistor) is either fully on or completely off.
When the switch is on, a large current flows through it, dropping only a
small voltage. Power loss (V x I) is also small.
When the switch is off, there is a large voltage across it, but very little
current flow. The power loss is again small.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 21
The switch only operates in its dissipative linear region for very brief
periods of time. The overall power loss is much less than for a linear dc
to dc convertor.
The switch is closed for the time Ton, and open for the time Toff.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 22 www.voltech.com Issue 2
When the switch is closed, there is a constant voltage (Vin - Vout)
across the inductor L, and the current in the inductor ramps up at a rate
given by:
When the switch is opened, the voltage across L reverses as it tries to
maintain the same current through itself. This voltage is clamped by the
diode and the previous current is then restored. The voltage across L is
now reversed, however, and equal to Vout + Vd. where Vd is the
forward voltage drop of the diode. The current thus ramps down at a
rate:
dd
= (V + V )L
it
out d
The current in L is the sum of the switch current (during Ton) and the
diode current (during Toff). The average value of these currents is the
output current.
FORWARD CONVERTOR - Energy stored in L during ON time. Vout < Vin
The inductor operates with a high DC bias current. It is made with a
gapped ferrite core, or a powdered alloy core which has an effective
distributed air gap.
L
)V - (V = dd
dd = V outin
t
i
t
i
during
Ton
during
Toff
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 23
Ton and Toff remain constant for output current changes if the input and
output voltages remain the same. The waveforms remain essentially the
same, except that the DC current in the inductor changes. For very low
output currents the inductor current will fall to zero for some period of
time. The inductor current is said to be discontinuous, the DC to DC
convertor operating in discontinuous mode.
For example:
When the inductor current is zero, the voltage across it will also tend
towards zero, often ringing first. The relationship:
V = V TT + T
out inon
on off×
no longer holds. This can cause problems in the design of the control
circuit, and regulation problems in buck type convertors with more than
one output.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 24 www.voltech.com Issue 2
Buck Regulator (Summary):
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 25
Advantages: Efficient
Simple, low cost.
Disadvantages: No isolation
Only one output
Higher output ripple than linear.
Step down only.
High frequency switching generates
RFI and EMI.
Applications: 5 to 50W. Local regulation
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 26 www.voltech.com Issue 2
4.1.2 Single Ended Forward Convertor.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 27
Advantages:
Isolated.
Relatively simple.
No flux symmetry problems.
Disadvantages:
Switch must withstand twice the input voltage.
Applications:
Up to 250W
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 28 www.voltech.com Issue 2
4.1.3 Push-Pull Convertor.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 29
Advantages:
Good use of transformer magnetic material.
Both parts of B-H loop used.
Disadvantages:
Problems of Volt-second imbalance
when switch times are different.
Applications:
Up to 3000W. Lower voltage inputs.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 30 www.voltech.com Issue 2
4.1.4 Two Transistor Forward Convertor.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 31
Adavantages:
Switches operate at Vin
Magnetising current, leakage current, returned to supply.
Disadvantages:
Poor use of transformer B-H loop.
Floating' switch drive required.
Applications:
Up to 500W. Higher input voltages.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 32 www.voltech.com Issue 2
4.1.5 Half Bridge Convertor.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 33
Advantages:
Volt-second balance ensured by C1.
Switches rated at Vin.
Both parts of B-H loop used.
Disadvantages:
Extra high frequency capacitor (C1) required.
'Floating' switch drive required.
Only ½ Vin applied to transformer primary.
Applications:
Up to 500W.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 34 www.voltech.com Issue 2
4.1.6 Full Bridge Convertor.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 35
Advantages: No flux symmetry problems. Transformer stored energy returned to supply. Transistors rated at Vin nominally. Good utilization of transformer magnetic material Disadvantages: Transistors, and 4 transistor drive circuits required. Applications: 200 to 2000 Watts
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 36 www.voltech.com Issue 2
4.2 Flyback (Boost) Convertors.
All the DC to DC convertors described so far have been examples of
forward convertors. That is energy is transferred from the input to the
output filter during the on time of the switch.
FORWARD CONVERTOR - Energy stored in L during ON time. Vout < Vin
In the flyback - or boost convertor, energy is stored in the inductor
during the on time, and released to the output during the off time only.
4.2.1 Boost Convertor
When the switch is closed, current ramps up in the inductor, L.
dd
it
VL
or = V TL
in in on≈ ∆
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 37
When the switch is opened the inductor tries to maintain the previous
current flow. The inductor voltage reverses rapidly until it reaches the
output voltage, when the diode conducts.
Current then flows into the output, ramping down at a rate:
didt
= V - VL
or i = (V - V )L
Tout in out inoff∆
Advantages: Low cost. Few components.
Disadvantages: Large di/dt generate noise and EMI
Fast rectifier required. Applications: Step up convertors. PFC circuits.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 38 www.voltech.com Issue 2
4.2.2 Discontinuous Flyback.
Extra windings are added to the inductor of the boost convertor to form the transformer/inductor of the flyback convertor.
When the switch is opened the voltage across the transformer/ inductor reverses until current flows in the outputs. The voltage across the transformer primary will then be:
Vfb. = (Vout + Vdiode) × N Vfb. is called the Flyback voltage.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 39
Note the orientation of the windings. The dot end is positive during Ton
- current flows in the primary.
The non dot end is positive during Toff - current flows in the secondary.
Volt-second balance is maintained
Vin Ton = Vfb T1
The transformer/choke current is zero during the time Td. The convertor
is said to be operating in discontinuous mode.
Advantages:
Only one magnetic component - even for multiple
outputs with isolation.
Only one diode per ouput.
Disadvantages:
Large peak currents in all components.
Large current and voltage changes generate noise and EMI.
Switch rated at Vin + Vfb + leakage spike.
Applications: Up to 200W. Low cost, multiple outputs.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 40 www.voltech.com Issue 2
4.2.3 Continuous Flyback.
Flyback convertors can also be operated in continuous mode:
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 41
Advantages: Peak currents reduced from discontinuous flyback. Only one magnetic component - even for multiple outputs. Only one diode per output. Disadvantages: Magnetics larger (for DC bias) Large peak currents in all components. Large current and voltage changes generate noise and EMI. Switch rated at Vin + Vfb + leakage spike. Applications: Up to 200W. Low cost, multiple outputs.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 42 www.voltech.com Issue 2
4.3 Resonant Convertors.
To further reduce the size and weight of the filter components in a dc to
dc convertor (and hence reduce the size and weight of a power supply)
higher operating frequencies are used.
It is also desirable to improve efficiency to minimise losses and reduce
temperature rises.
Switching losses limit ‘square wave’ operation to about 200kHz.
Resonant convertors use LC circuits, which operate with sinusoidal
currents at near the resonant frequency (F) of the L and C.
Parallel and Series L - C Circuits
The switching device can be arranged to operate when either the voltage
or current is naturally zero, thus minimizing switching losses.
There are many different types of resonant convertor, operating in
different ways. Some switch at zero current (ZCS) or zero voltage
(ZVS) with parallel or series L-C circuits.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 43
A simple form of resonant convertor can be made by adding a capacitor
to the circuit of a forward convertor. The filter L and C operate in much
the same way as in the conventional forward convertor. The transformer
is deliberately wound with a large value of leakage inductance.
The leakage inductance of the transformer (LL) and the reflected value
of the resonant capacitor Cr form a series resonant circuit
F = 1/ 2p √ (LLCr(Ns/Np)
Referring to the following diagram when the switch is closed, a
sinusoidal current begins to flow in the resonant circuit. Energy is
transferred to the output during this time. The negative half cycle of
current flows in the diode D1. The transistor may be switched off at any
point during this time, since there is no current flowing in it.
T1 < Ton < T2
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 44 www.voltech.com Issue 2
No current in switch when it is turned off - Reduced turn off loss
When D1 stops conducting, current can only flow in the parallel
magnetising inductance/resonant capacitor circuit. The transformer core
is reset during this time.
The pulse width is fixed by the values of L and C, however. The output
voltage is controlled by varying the frequency of operation.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 45
Advantages:
Lower weight and volume, high efficiency
EMI from switching transients reduced.
‘Stray’ circuit elements - capacitance, leakage inductance,
etc. utilised.
Disadvantages:
High peak currents in all components.
Variable frequency operation
- cannot be synchronised to external frequency.
- more difficult to design against EMI.
Applications:
Where reduced size/weight and improved efficiency required.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 46 www.voltech.com Issue 2
4.4 Magnetic Amplifiers.
Dc to dc convertors may have several outputs. One 'master' output is
well regulated by a control circuit, other 'slave' outputs are at nominally
the correct voltage, but will have poor load and line regulation.
Cross regulation may also be observed. This is the voltage change on
one output due to the load current change on another.
Slave output regulation can be improved by increasing the coupling
between transformer windings or sharing regulation.
If the best regulation - or a separately adjustable output - is required
then further dc to dc convertors (linear or switched mode) can be used.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 47
In forward convertors, magnetic amplifiers can be used to perform the
post regulation.
The magnetic amplifier acts as a switch in series with a secondary
winding in a forward convertor
Normally, V = V TT + T
OUT SEC ON
ON OFF ×
The magnetic amplifier works by introducing a time Tblock to reduce
the effective pulse width and hence the output voltage.
V = V (T - T )T + T
OUT SEC ON BLOCK
ON OFF
×
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 48 www.voltech.com Issue 2
A magnetic amplifier consists of a number of turns of wire wound on a
core that has a very square B-H loop.
In the steep, vertical parts of the B-H loop µr and hence the inductance
is very high. SWITCH = OPEN.
When Bsat is reached a large current flows. SWITCH = CLOSED.
At the start of a cycle, the core is at point A on the B-H loop. When Vs
becomes positive, very little current flows until Bsat is reached. This
takes a time Tblock. (Volt-seconds = Vs.Tblock)
Once Bsat is reached the voltage across the Magnetic amplifier (MA)
collapses and a large current flows.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 49
Once Vs collapses the magnetic amplifier core is reset by a control
circuit. If the core is reset to a point other than A then the time taken to
reach Bsat (Tblock) on the next cycle will be different.
The current through D3 resets the core of the Magnetic amplifier (MA).
The point on the B-H loop to which the MA is reset controls the
blocking time (TBLOCK) when VSEC next goes positive. TBLOCK is varied
so as to regulate the ouput voltage.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 50 www.voltech.com Issue 2
4.5 PWM Control Circuits.
4.5.1 Voltage Mode.
The output voltage of switched mode dc to dc convertors is controlled
by changing the ratio:
TT
ON
ON + TOFF
Ton or Toff may be varied, but common control circuits operate at a
fixed frequency ( Ton + Toff = constant) and vary Ton.
E.g.
If Vout = 5V required, and Vout = d x Vin
Vin = 20V, d = 0.25
Vin = 25V, d = 0.20
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 51
PWM circuits consist of:
An error amplifier which amplifies the difference between a reference
voltage (desired output voltage) and the actual output voltage.
A comparator which compares the error amplifier output voltage
(control voltage) with a sawtooth waveform. The output of the
comparator is a pulse waveform at the frequency of the saw-tooth. The
pulse width varies directly with the control voltage.
If Vout tries to rise, Vcontrol falls and Ton is reduced, maintaining
Vout.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 52 www.voltech.com Issue 2
Low cost integrated PWM circuits are available that contain the required
error amplifier, comparator and oscillator/sawtooth generator.
• Other useful features often included are:
• On chip oscillator/sawtooth generator.
• Drive transistors for easy connection to power switch transistors.
• Extra error amplifiers/comparators for overcurrent protection,
• remote shutdown etc.
• Logic to provide push - pull outputs.
• Under voltage lock out (UVLO) to inhibit operation if a
reasonable reasonable if a reasonable input voltage is not present.
Voltage feed forward technique.
With this technique, the amplitude of the sawtooth waveform is changed
with the input voltage. The duty cycle, d, is reduced automatically. The
output voltage is maintained without the control voltage changing.
The benefits are:
• Quick responses to input voltage changes.
• Inherently good line regulation - and hence,
• Less error amplifier gain required - easier to stabilize loop.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 53
4.5.2 Current Mode.
In current mode control, the peak inductor current is controlled, rather
than the duty cycle directly.
This is done by using the inductor current ramp waveform as the
sawtooth input to the PWM comparator.
E.g. Continuous mode forward convertor.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 54 www.voltech.com Issue 2
At the start of a clock cycle, the PWM output goes high, turning the
switch ON. Current ramps up in the output inductor and transformer
primary. This current forms the ramp voltage which is compared to the
control voltage. When the ramp voltage reaches VCONTROL the PWM
output goes low and the switch is turned OFF, due to the combination of
comparator action and logic control.
The voltage error amplifier now controls the peak inductor current,
which is varied so as to maintain the desired output voltage.
Current Mode Control
Advantages:
Inherent pulse by pulse current lmiting.
Protects switching device(s) from overcurrent.
Volt - second balance maintained in push-pull
circuit since alternate current pulses must have
the same amplitude.
Inherent voltage feed forward.
The slope of the ramp varies with input voltage.
Easier feedback loop stabilisation.
The voltage feedback loop now controls the inductor
current. In a continuous mode forward convertor the
small signal model feeding the output capacitance and
the load resistance. The gain/phase response of the
inductor is eliminated.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 55
Advantages (contd)
Easier paralleling of convertors.
A common control voltage is fed to the comparator
of each current mode controlled convertor. The same
current must then flow in each convertor.
Disadvantages:
Poor noise immunity.
The ramp voltage is shallow compared to the
voltage mode sawtooth.
The ramp voltage is derived from a real circuit
current - often the switch current - which will
contain noise, and a large turn on peak.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 56 www.voltech.com Issue 2
Current Mode Control Slope Compensation
Ideally, the current mode controller should control the average inductor
current rather than the peak to optimise the small signal performance of
the dc to dc convertor.
The difference between peak and average current changes with input
voltage, since the slope of the ramp changes.
Average inductor current control is achieved by introducing a
compensating slope into the control voltage. ( Most current mode IC's
provide a convenient way of doing this)
Slope compensation also improves the noise immunity.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 57
5 Power Factor Correction.
Power factor is defined as the ratio:
PF = WattsVA
Power factor is only equal to 1 when both waveforms are of the same shape and in phase.
The current drawn by a line input power supply is heavily distorted as in I3. Cos Ø may be equal to 1, but PF is not equal to 1.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 58 www.voltech.com Issue 2
A power factor correction (PFC) circuit can be introduced which forces
the input current to follow the voltage input in shape and phase.
A typical PFC circuit consists of a continuous mode boost converter
between the bridge rectifier and reservoir capacitor of a line input power
supply.
The switch operates under PWM control, such that the average inductor
current follows the rectified input voltage V bridge.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 59
The rectified input voltage, Vbridge, forms the reference for the PWM
error amplifier. The PWM circuit ensures that the average boost
convertor current 'follows' this voltage.
A second control loop modifies the amplitude of the reference voltage
derived from Vbridge to maintain a constant boost output voltage, Vdc.
Vdc is maintained at a voltage above the peak input voltage to ensure
correct operation.
The design of the isolated dc to dc converter can be simplified, and
'universal' input voltage readily achieved because the PFC circuit
regulates Vdc.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 60 www.voltech.com Issue 2
Current ripple due to the PFC boost converter can be removed by
passive filtering at the input. The filter used for high frequency
conducted noise (RFI) may be sufficient.
Note that if the voltage waveform is distorted, then the current
waveform - since it follows the voltage - will also be.
Since international standards like IEC6100-3-2 seek to limit the
harmonic distortion in the current, and not power factor, this may be a
problem in higher power applications.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 61
6 Inrush Current protection.
When an ac line input power supply is first switched on a large current
flows into the input reservoir capacitor, C.
The capacitor is initially discharged and presents a very low impedance
to the line. The peak current falls towards its normal operating value as
the voltage across the capacitor builds up.
Large values of inrush current can:
• Disturb the a.c. line voltage.
• Exceed diode peak current ratings, shortening their life.
• Cause fuses or circuit breakers to open.
A resistor can be added to limit inrush current.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 62 www.voltech.com Issue 2
During normal operation the resistor dissipates power,
W = Irms²R
This power may be several watts, degrading the power supply efficiency and causing local heating.
The resistor can be made of a material with a sharp negative temperature
coefficient (NTC).
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 63
When cold the NTC 'thermistor' has a significant resistance which limits
the inrush current.
As current continues to flow the thermistor heats up, and its resistance
falls, reducing its continuous dissipation.
If the ac line is removed only briefly, the reservoir capacitor discharges,
but the NTC thermistor will remain hot, allowing a large inrush current
to flow when the ac line is restored.
Active inrush current limiting uses a semi-conductor device, an SCR, to
short circuit the inrush limiting resistor once the normal operating
current has been established.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 64 www.voltech.com Issue 2
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 65
7 Summary of Power measurements Required on
Power Supplies.
Regulated
D.C. Outputs
Volts - RMS Amps - RMS Amps - PEAK Amps - Harmonic Content Watts - Real Power VA - Apparent Power P.F. - True power factor Inrush Current
Volts - RMS a.c. Volts - BUS a.c. to d.c. Amps - RMS Amps - Peak Watts - Real Power Inrush Current
Volts d.c. Amps d.c. Watts d.c.
Efficiency of Input Circuit (including PFC) D.C. to D.C.
Converter Efficiency. Overall Efficiency.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 66 www.voltech.com Issue 2
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 67
8 Power Supply Measurements.
8.1 Volts, Amps and Watts.
Power supplies connected to the ac line generally draw distorted, non sinusoidal currents as in i3 below.
Many ac voltage and current meters respond to the average value of a waveform and although calibrated in rms are only accurate for pure sine waves. (Crest factor A cf = 2)
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 68 www.voltech.com Issue 2
Even bench top ‘True RMS’ electronic meters may specify maximum
crest factors as low as 3. There may also be dc components present
which will be ignored by ac coupled instruments.
Voltech power analyzers obtain RMS (Root Mean Squared) values by
taking a large number of instantaneous voltage and current samples over
a few cycles of a waveform with period, T.
V = IN
V and I IN
Irms rms nn=N n=N
n o n on
= =∑ ∑2
2
according to the definition of RMS values.
Thus true RMS values are obtained, even for highly distorted
waveforms. Voltech power analysers are also AC + DC coupled.
In a similar fashion, power (Watts) is computed by summing the product
of the simultaneous and instantaneous v and i sample over a number of
samples.
This is the best method of determining true power.
Wattsn o
n = IN
(V I )n=N
n=
×∑
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 69
RMS Measure accurately true RMS value of input voltage.
A RMS Measure accurately true RMS value of input current,
even for highly distorted waveforms.
Size conductors, fuses, filters, rectifiers, etc.
WATTS Measure true input power.
connection diagram
To measure volts, amps and watts:
Connect the analyzer as shown below.
Select normal measurement mode on PM1000+
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 70 www.voltech.com Issue 2
8.2 VA and PF
Apparent power, VA, is computed as : VA = Vrms × Arms
The true power factor is then PF = Watts ÷ VA
For sinusoidal voltages and currents, power is often expressed as:
Power(W) = Vrms × Arms × cos .
Were is the phase angle between the voltage and current waveforms.
The distorted current drawn by a power supply may be in phase (cos ø =
1) but will have a low power factor due to the harmonic distortion in the
current waveform. See Appendix D.
VA is often measured to ensure that the ac supply has sufficient capacity
- Uninterruptable power supplies (UPS). For example:
PF includes effect of harmonic as well as phase distortion.
Confirms operation of a PFC circuit.
To measure VA, PF:
Connect the analyser as shown in the connection diagram on
page 68
Select VA and PF in measurement mode.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 71
8.3 Peak Repetitive Current and Current Crest Factor.
A sinusoidal current has a crest factor of 2 (=1.41).
Ipk(sinewave) = 2 x Irms
Crest factor = Ipk/Irms
In power supplies which rectify the AC line input the repetitive peak
current can be several times larger than its RMS value.
To measure current crest factor
Connect the analyser as shown in the connection diagram on
page 68.
Select Acf in the measurement mode of PM1000+
Peak current may also be displayed on a PM3000A -
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 72 www.voltech.com Issue 2
Measurements should be made with a low impedance ac supply.
Isolating transformers and autotransformers have an impedance which
may reduce the crest factor.
Apk and Acf are measured to ensure that the ac supply can deliver the
peak current requirement. Very important if the supply is a UPS for
example.
Vpk may also be measured on the dc bus. Peak voltage will determine
the capacitor voltage rating.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 73
8.4 Peak Inrush Current.
Every time a power supply is switched on it draws an inrush current
which can be several times larger than the steady state peak current.
INRUSH A
Correctly specify I2t rating of fuses and circuit breakers.
Determine peak current rating required for rectifier diodes etc.
Determine effect of the inrush current on the a.c. supply
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 74 www.voltech.com Issue 2
Voltech PM1000+ Power Analyser
To measure inrush current:
Connect the analyser as shown in the connection diagram on page
68
Select INRUSH mode
Select a suitable amps range.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 75
A worst case measurement will be made when:
There is a low impedance connection to the supply.
The power switch is closed at the peak of the voltage cycle.
The reservoir capacitor has fully discharged.
NTC thermistor (if used) is still warm.
Thus by repeating the measurement many times, a reliable worst case
figure may be established.
Measurements can be simplified by using a solid state switch in line with
the AC supply, such as the Voltech PS1000. This allows the AC supply to
be accurately turned on at either the zero-crossing or the peak value of the
voltage waveform. The PS1000 is self powered, rated to 200A peak, and
has a fully isolated oscilloscope trigger output to allow viewing of the
waveform. In this case, it will only be necessary to make a single
measurement to obtain peak reading..
Voltech PS1000 Inrush Switch
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 76 www.voltech.com Issue 2
8.5 Losses and Efficiency.
The efficiency of a power supply is usually expressed as a percentage,
Efficiency = Output Power x 100%
Input power
e.g. for a 3 (d.c.) output power supply: Efficiency = [(V1 × A1) + (V2 × A2) + (V3 × A3)] × 100%
Input Power
Ordinary multimeters of sufficient accuracy can be used to measure the
output power, since they are true dc.
An electronic power analyzer such as the Voltech series is essential for
measuring the true input power.
Power Losses = Input power - output power
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 77
The power lost in a power supply is generally dissipated in the form of
heat. Inadequate heat-sinking and ventilation will lead to excessive
component temperatures. When verifying a design it is important to
account for all losses and ensure that the individual component losses
are within their design limits.
Voltech analyzers can also make accurate power measurements on the
dc bus of a power supply. This is especially useful when determining
the efficiency of a power factor correction circuit.
The PM6000 will measure and display efficiency directly.
For example, measuring the efficiency of a PFC circuit a PM6000 will
group up to 2 sets of 3phase measurement channels, for example power
input as Group A and power output as Group B.
With the on board math function efficiency can displayed directly on the
screen of the PM6000.
Voltech PM6000 Power Analyzer
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 78 www.voltech.com Issue 2
8.6 Amps Harmonics
Using Fourier analysis, a distorted current waveform, such as that drawn
by a power supply, can be shown to consist of a fundamental component
(at the supply frequency) plus a series of harmonic components (at
multiples of the supply frequency):-
International standards such as EN61000-3-2 specify limits for the
amplitude of each harmonic up to the 40th.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 79
Measuring to EN61000-3-2.
The standard specifies different limits for different types of equipment
in four Classes A, B,C, and D. Also, the measurement method is
complicated with specific measurement window and digital sampling
and filtering techniques specified. For measurement in full-compliance
to the standard, please see the detailed information available for the
Voltech PM6000 power analyzer on our website at www.voltech.com.
The PM6000 full-compliance methods are used by leading EMC Test
Laboratories across the world.
The PM1000+ power analyzer is suitable for making pre-compliance
EN61000-3-2, by comparing the measured harmonic amplitudes with
the specified limits. Please contact your Voltech supplier for more
information.
PM1000+ Real time Harmonic Display
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 80 www.voltech.com Issue 2
8.7 Total Harmonic Distortion (THD)
THD is a measure of the distortion of a waveform.
Voltage THD is used to check the purity of the voltage supply to a
power supply. A very pure voltage supply should be used when
checking current harmonics in accordance with standards like
IEC61000-3-2.
Current THD may be used to check the power supply against
specification and to help confirm the correct operation of power-factor
correction circuits.
THD is calculated from harmonic measurements according to the
formula:
REF....HHHHthd ++++=
2222 5432
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 81
8.8 Line Regulation
This is a measure of the ability of the power supply to maintain (or
regulate) its output voltage when the input ac line changes.
To measure line regulation, the main output voltage, Vo, is measured at
three points with the output load current kept constant.
Line regulation = Vo (Highline) – Vo (Lowline) x 100 %
Vo (Nominalline)
Where Vo (Highline) = Vo at maximum ac input voltage
Vo (Lowline) = Vo at minimum ac input voltage
Vo (Nominalline) = Vo at nominal line voltage.
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 82 www.voltech.com Issue 2
8.9 Load Regulation
This is a measure of the ability of the power supply to maintain (or
regulate) its output voltage when the output load changes.
To measure load regulation, the main output voltage, Vo, is measured at
three points with the ac input voltage kept constant.
Load regulation = Vo (Highload) – Vo (Lowload) x 100 %
Vo (Nominalload)
Where Vo (Highload) = Vo at maximum dc load
Vo (Lowline) = Vo at minimum dc load current
Vo (Nominalload) = Vo at nominal load.
Cross regulation may also be measured and is calculated as the
percentage change on one dc output when another dc output load is
changed from minimum to maximum as above.
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 83
9 Example Power Supply Measurements.
PM1000 Output
RESULTS OF MEASUREMENTS
Watts +86.61100 W
VA 134.58000 W
PF - 0.64355
Vrms 246.80000 V
Arms 0.54528 A
Vcf 1.38
Acf 2.55
Freq 50.10700 Hz
AH0 - 0.00422 A - 1.16 % 0.0 deg
AH1 0.36558 A 100.00 % - 349.1 deg
AH2 0.00266 A 0.72 % - 244.7 deg
AH3 0.30718 A 84.01 % - 179.9 deg
AH4 0.00233 A 0.62 % - 44.4 deg
AH5 0.21917 A 59.94 % - 3.1 deg
AH6 0.00157 A 0.42 % - 194.4 deg
AH7 0.12045 A 32.94 % - 182.6 deg
AH8 0.00105 A 0.27 % - 345.1 deg
AH9 0.03613 A 9.88 % - 2.9 deg
AH10 0.00076 A 0.19 % - 106.1 deg
AH11 0.01948 A 5.32 % - 0.8 deg
AH12 0.00092 A 0.24 % - 218.8 deg
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 84 www.voltech.com Issue 2
AH13 0.04179 A 11.42 % - 180.2 deg AH14 0.00106 A 0.28 % - 19.2 deg AH15 0.03770 A 10.30 % - 357.9 deg AH16 0.00077 A 0.20 % - 164.0 deg AH17 0.01750 A 4.78 % - 166.6 deg AH18 0.00077 A 0.20 % - 300.5 deg AH19 0.00735 A 2.01 % - 232.0 deg AH20 0.00076 A 0.19 % - 70.3deg AH21 0.01931 A 5.28 % - 18.6 deg AH22 0.00074 A 0.19 % - 214.9 deg AH23 0.01980 A 5.40 % - 192.1 deg AH24 0.00071 A 0.18 % - 11.1 deg AH25 0.01127 A 3.08 % - 6.6 deg AH26 0.00077 A 0.20 % - 117.9 deg AH27 0.00195 A 0.52 % - 96.7 deg AH28 0.00057 A 0.14 % - 260.9 deg AH29 0.00882 A 2.41 % - 207.6 deg AH30 0.00073 A 0.19 % - 46.8 deg AH31 0.01071 A 2.92 % - 25.7 deg AH32 0.00047 A 0.12 % - 227.6 deg AH33 0.00621 A 1.69 % - 204.1 deg AH34 0.00017 A 0.03 % - 333.4 deg AH35 0.00008 A 0.01 % - 201.7 deg AH36 0.00079 A 0.20 % - 182.0 deg AH37 0.00524 A 1.43 % - 23.1 deg AH38 0.00028 A 0.06 % - 220.5 deg AH39 0.00636 A 1.74 % - 201.1 deg AH40 0.00034 A 0.08 % - 66.9 deg
Application Note 107 The VOLTECH HANDBOOK of POWER SUPPLIES
Issue 2 www.voltech.com Page 85
10 Measurement Instrumentation.
To make credible measurements of on power supplies it is essential to
use appropriate equipment. The power analyzer must be accurate on all
waveforms and safe and easy to use. A power analyzer such as the
Voltech PM1000+ provides the following:
• Fully isolated inputs, using 4mm safety connectors.
Safe to use and connect.
• Wide range of input voltage, current and frequency.
Up to 600V, 20A, 1Mhz
Range from uA to MA with external transducers
• Accuracy on all ranges
0.1% basic
The VOLTECH HANDBOOK of POWER SUPPLIES Application Note 107
Page 86 www.voltech.com Issue 2
• Harmonics as standard
harmonic 0 to 50
• Versatile display
4 or 14 measurements on the front panel
• Waveform display
Volts, amps and watts
• Harmonic barchart display
For an easy overview of harmonics.
• Easy to use
On-board menu and help system
• Interface for production automatic test
RS232, GPIB, USB and Ethernet
• PC Software
for control and recording of measurements.
For the latest information, please see our website at:
www.voltech.com