the owner's guide to piano...
TRANSCRIPT
The Owner's Guide to Piano Repair
Focus On: Grand Damper Replacement
Information provided courtesy of:
Ed Tomlinson - California Keyboards Music Center
661-342-0367
email: [email protected]
www.pianotunerbakersfield.com
Page 2
Dampers are to a piano what brakes are to an automobile. While the
action, strings, and soundboard of the piano are all devoted to the production of sound, the sole purpose of the dampers is the cessation of sound. The fact that a
grand piano can go from a thunderous crescendo one second to nearly complete
silence the next is a testament to the genius of the design of the grand damper. The
dampers on your piano, however, have reached the point in which their effec-
tiveness has been compromised by wear and tear. Replacement of the old
damper felts with a set of new high-quality dampers is the solution.
The following commonly asked questions have been answered to give you the
information you need in order to decide whether or not to have me replace
the dampers on your grand piano.
What are the symptoms of dampers which have excessive wear and tear?
Just as worn-out brakes on your car announce their condition with unwant-
ed sounds that are characteristic of the problem (high-pitched squealing or scrap-
ing noise upon braking), so will worn-out dampers be detectable by what's heard
when the piano is played. Specifically, when the sustain pedal is released, the
transition from sound to silence won't be immediate, but will be more prolonged
than usual—a symptom of ineffective dampers unable to quickly absorb the ener-
gy of the strings. Also, when individual notes are played, a faint "zinging" sound
might be heard after the note is played as the strings buzz for an instant against
the harder than normal surface of the old felt.
Page 3
How do effective dampers work, and what happens to them physically as
they wear out?
A damper has the ability to absorb the energy of a string hundreds of times
as massive as itself and to quell its vibration in a split-second. For this to happen,
the damper material must be firm enough to hold its shape (damper on left in
above photo) but soft enough to instantly muffle the sound of the strings. Preci-
sion alignment of the dampers
on the strings is also a neces-
sary factor.
Dampers often become
hardened or misshaped with
age, as seen with the damper
on the right in the above photo.
The treble dampers in the pho-
to to the side illustrate clearly
why worn-out dampers do not
function as intended. In such a
case, replacement of the old
dampers with a new set is the
only option.
Page 4
What's the typical procedure for this job? Is this a repair that must be done
in the workshop?
Unless the piano is in the workshop for an extensive restoration work, there
is no reason to transport the instrument to the shop. However, it may make sense
to take the damper assemblies to the shop for at least part of the work to be done.
To access and remove the damp-
er assemblies, the case will need to be
disassembled to the extent that the ac-
tion and keys may be drawn out of the
piano. After removing the action from
the piano, each damper will be taken
out in order by loosening the set screw
which holds the damper wire in place.
The wooden blocks that the
damper felts are attached to (known as
the damper heads) are ordinarily
saved. The old felts are removed with
a sharp chisel. While this job could be
done in the home, the tools and equip-
ment of the shop (such as the bench
vise being used in the photo to the
right) make the process simpler and
more precise.
The lower surface of damper
head is then scraped and sanded clean.
The upper surface of the damper head
may be cleaned and polished if the
original lacquer finish is still in good
shape. Otherwise, the old finish may
need to be stripped off, so that a new
lacquer finish can be applied (note-
extra work =extra cost). A final step
will be the polishing of the damper
guide wires.
Page 5
Do other repairs go hand-in-hand with the installation of a set of dampers?
Yes. If the piano is in need of restringing, now would be the time to do it in
that the two jobs compliment each other. Since the dampers conform to the strings
(especially the wound bass strings shown in the photo above), it makes sense to
have new strings and new dampers installed at the same time.
Additionally, the condition of the damper guide rail should be taken into
account. If the bushings that the damper wires pass through are worn, this would
be the obvious time to rebush the guide rail.
Once the damper
heads and guide wires
have been attended to,
new damper felts will
be glued in place, usual-
ly at the piano. High
quality, precut damper
felts are available for
many grands. At other
times, felt may be cut
from strips so that the
length of the dampers is
precisely fitted to the
damper heads.
Many times, the
preferred practice is to
reinstall the damper
heads and wires in the
piano, then glue the
damper felts in place,
using the strings them-
selves to serves as the
clamps while the glue
dries. This way, align-
ment of the felt to the
strings is sure to be pre-
cise.
Page 6
Once the damper felts are glued in place, is that all that needs to be done?
No. There is always a great deal of fine adjustment involved to finish the
job. The dampers must lift as a unit (above photo), giving the appearance of all
being solidly connected. When the dampers lift, individual damper heads should
not be seen swiveling one way or the other in random directions. Most important-
ly, when the dampers make contact with the strings upon release of the sustain pe-
dal, they must all touch at exactly the same moment in order for cessation of
sound to be precise.
Complicating this adjustment
is the fact that different types of
dampers are used for different sec-
tions of strings, and the profiles of
these various dampers are not the
same at all. In the photo to the right
are shown single wedge dampers
(used for the largest bass strings),
double wedge dampers (used for
notes with a pair of bass strings),
trichord dampers (used for larger
steel treble strings, and flat treble
dampers (used for smaller steel treble strings). Obviously, a great deal of fine ad-
justment is necessary to make all these parts perform in unison with one another.
Page 7
A new set of dampers installed and ready quiet things down when needed.
In business to bring your piano to its full potential.
Please advise me when you wish to have this repair professionally done.
Ed Tomlinson - California Keyboards Music Center
661-342-0367
email: [email protected]
www.pianotunerbakersfield.com