test report no. : 12406766s · non-radio test related requirements. (if applicable) 6. the all test...

Test report No. : 12406766S Page : 1 of 24 Issued date : August 23, 2018

UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 13-EM-F0429

RADIO TEST REPORT

Test Report No. : 12406766S

Applicant : TAIYO YUDEN CO., LTD. Type of Equipment : Bluetooth low energy / ANT Module Model No. : EYSLSN Test standard : EN 300 328 V2.1.1 Test Result : Complied

1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the above standard(s). 4. The test results in this report are traceable to the national or international standards. 5. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or

non-Radio test related Requirements. (if applicable) 6. The all test items in this test report are conducted by UL Japan, Inc. Shonan EMC Lab and Kashima EMC Lab. 7. The opinions and the interpretations to the result of the description in this report are outside scopes where UL

Japan has been accredited.

Date of test: July 23 to 27, 2018 Representative test engineer: Shiro Kobayashi

Engineer Consumer Technology Division

Approved by :

Hikaru ShirasawaEngineer

Consumer Technology Division

RTL02610 The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan.

There is no testing item of "Non-accreditation".

48085

Pencil


UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401

REVISION HISTORY

Original Test Report No.: 12406766S

Revision Test report No. Date Page revised Contents -(Original) 12406766S August 23, 2018 - -



CONTENTS PAGE

SECTION 1: Customer information ................................................................................... 4

SECTION 2: Equipment under test (E.U.T.) ..................................................................... 4

SECTION 3: Test specification, procedures & results ...................................................... 5

SECTION 4: Operation of E.U.T. during testing ............................................................... 8

SECTION 5: Antenna Terminal Conducted Tests .......................................................... 11

APPENDIX 1: Test data ........................................................................................................ 12

RF Output Power ........................................................................................................................ 12 Power Spectral Density ............................................................................................................... 14 Occupied Channel Bandwidth .................................................................................................... 15 Transmitter unwanted emissions in the out-of-band domain ...................................................... 19 Receiver Blocking ....................................................................................................................... 20

APPENDIX 2: Test instruments ........................................................................................... 22

APPENDIX 3: Photographs of test setup ............................................................................. 23

Antenna terminal conducted tests other than Receiver Blocking ............................................... 23 Receiver Blocking ....................................................................................................................... 24



SECTION 1: Customer information Company Name : TAIYO YUDEN CO., LTD. Address : 8-1,Sakae-cho, Takasaki-shi, Gunma 370-8522 ,Japan Telephone Number : +81-27-324-2313 Facsimile Number : +81-27-324-2314 Contact Person : Hideki Kato

SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Bluetooth low energy / ANT Module Model No. : EYSLSN Serial No. : Refer to Clause 4.2 Rating : DC 3 V (DC 1.7 V to DC 3.6 V), 0.02 A, 50 Hz Receipt Date of Sample : July 13, 2018 Country of Mass-production : Japan Condition of EUT : Engineering prototype

(Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description Model: EYSLSN (referred to as the EUT in this report) is a Bluetooth low energy / ANT Module. Radio Specification * Receiver category: 2

< Bluetooth (BT) Low Energy (LE) (1 Mbps, 2 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz - 2480 MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dBi Operating Temperature : -40 deg. C to +105 deg. C

< ANT (1 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz - 2480 MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dBi Operating Temperature : -40 deg. C to +105 deg. C < Nordic Original (2 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz - 2480 MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dBi Operating Temperature : -40 deg. C to +105 deg. C



SECTION 3: Test specification, procedures & results 3.1 Test Specification Radio : EN 300 328 V2.1.1 Title : Wideband transmission systems; Data transmission equipment operating in the 2.4GHz ISM

band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

Purpose of test : Compliance with the harmonized RE directive 2014/53/EU. 3.2 Procedures and results

No. Item Test Procedure

Limit Remarks Worst margin

Exclusions Results

1 RF output power Clause 5.4.2 Clause 4.3.2.2 Conducted See Data N/A Complied

2 Power Spectral Density

Clause 5.4.3 Clause 4.3.2.3 Conducted See Data N/A Complied

3 Duty cycle, Tx-sequence, Tx-gap

Clause 5.4.2 Clause 4.3.2.4 Conducted - N/A N/A*1)

4 Medium Utilisation (MU) factor


5 Adaptivity (adaptive equipment using modulations other than FHSS)


6 Occupied Channel Bandwidth


7 Transmitter unwanted emissions in the out-of-band domain


8 Transmitter unwanted emissions in the spurious domain

Clause 5.4.9 Clause 4.3.2.9 Radiated - N/A N/A*3)

9 Receiver Spurious emissions

Clause 5.4.10 Clause 4.3.2.10 Radiated - N/A N/A*3)

10 Transmitter unwanted emissions in the spurious domain


11 Receiver Spurious emissions


12 Receiver Blocking Clause 5.4.11 Clause 4.3.2.11 Conducted See Data N/A Complied 13 Geo-location

capability - Clause 4.3.2.12 - - N/A N/A*4)

Note: UL Japan, Inc.’s EMI Work Procedure 13-EM-W0420. *1) The test is not applicable since the EUT is an adaptive equipment and does not operate in a non-adaptive mode. *2) The test is not applicable since the RF output power of the EUT is less than 10 dBm (e.i.r.p.). *3) The test has not been performed according to the customer’s request. *4) The EUT does not have Geo-location capability. Symbols: Complied The data of this test item has enough margin, more than the measurement uncertainty. Complied# The data of this test item meets the limits unless the measurement uncertainty is taken into consideration.



3.3 Additions or deviations to standards No addition, exclusion nor deviation has been made from the standard. 3.4 Uncertainty The following uncertainties have been calculated to provide a confidence level of 95 % using a coverage factor k = 2. Shonan EMC Lab.

Frequency range Uncertainty (+/-)30 MHz - 200 MHz 4.8 dB200 MHz - 1000 MHz 3.6 dB1 GHz - 12.75 GHz 4.4 dB

Antenna terminal test Uncertainty (+/-)Power Measurement above 1 GHz (Average Detector)_SPM-06 0.48 dBPower Measurement above 1 GHz (Average Detector)_SPM-07 0.47 dBPower Measurement above 1 GHz (Average Detector)_SPM-08, 09, 10, 11 1.27 dBPower Measurement above 1 GHz (Average Detector)_SPM-13 0.90 dBConducted emissions Measurement (below 1 GHz) 1.8 dBConducted emissions Power Density Measurement (1 GHz-3 GHz) 1.7 dBConducted emissions Measurement (3 GHz-18 GHz) 2.5 dBConducted emissions Measurement (18 GHz-26.5 GHz) 2.5 dBFrequency Measurement (Spectrum Analyzer) 2.1 x 10^-7Bandwidth Measurement 1.01 %Duty cycle and Time Measurement 0.012 %Temperature 0.95 deg.C.Voltage 0.24 %Humidity 3.4 %Receiver Blocking (Wanted RF Level)_SWT-01 2.05 dBReceiver Blocking (Blocking Signal Level)_SWT-01 1.70 dBReceiver Blocking (Wanted RF Level)_SBT-01 1.97 dBReceiver Blocking (Blocking Signal Level)_SBT-01 1.68 dBReceiver Blocking (Blocking Signal Level)_without tester 1.68 dB

Substitution measurement (EUT height: 1.5 m, Distance: 3 m)

Kashima EMC Lab.

ItemUncertainty

(+/-)1.6 %

0.74 dBConducted emissions Measurement (below 6 GHz) 2.2 dB

2.2 dB0.89 deg. C

0.42 %0.012 %

Item Frequency range Uncertainty (+/-)Radiated emission (Measurement distance: 3 m) 30 MHz - 300 MHz 4.7 dB

300 MHz - 1 GHz 3.6 dB1 GHz - 13 GHz 4.8 dB

2.3 dB

Occupied Channel Bandwidth RF output power, conducted

Time

Receiver Blocking

Conducted emissions Measurement (6 GHz - 18 GHz)Temperature Supply voltages



3.5 Test Location UL Japan, Inc. Shonan EMC Lab.1-22-3, Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPANTelephone: +81 463 50 6400, Facsimile: +81 463 50 6401JAB Accreditation No. RTL02610

Test siteIC RegistrationNumber

Width x Depth xHeight (m)

Size of reference ground plane (m) /horizontal conducting plane

Maximummeasurementdistance

No.1 Semi-anechoicchamber

2973D-1 20.6 x 11.3 x 7.65 20.6 x 11.3 10m


2973D-2 20.6 x 11.3 x 7.65 20.6 x 11.3 10m


2973D-3 12.7 x 7.7 x 5.35 12.7 x 7.7 5m


- 8.1 x 5.1 x 3.55 8.1 x 5.1 -

No.1 Shielded room - 6.8 x 4.1 x 2.7 6.8 x 4.1 -No.2 Shielded room - 6.8 x 4.1 x 2.7 6.8 x 4.1 -No.3 Shielded room - 6.3 x 4.7 x 2.7 6.3 x 4.7 -No.4 Shielded room - 4.4 x 4.7 x 2.7 4.4 x 4.7 -No.5 Shielded room - 7.8 x 6.4 x 2.7 7.8 x 6.4 -No.6 Shielded room - 7.8 x 6.4 x 2.7 7.8 x 6.4 -No.8 shielded room - 3.45 x 5.5 x 2.4 3.45 x 5.5 -No.1 Measurementroom

- 2.55 x 4.1 x 2.5 - -

UL Japan, Inc. Kashima EMC Lab.1614 Mushihata, Katori-shi, Chiba-ken, 289-0341 JAPANTelephone: +81 478 88 6500, Facsimile: +81 478 82 3373JAB Accreditation No. : RTL02610

Test siteICRegistrationNumber

Width x Depth xHeight (m)

Size of referenceground plane (m) / horizontalconducting plane

Maximummeasurementdistance

No.1 Open site 4659A-1 6.0 x 5.5 x 2.5 20 x 40 10 m



No.1 Shielded room 4659A-1 5.4 x 4.5 x 2.3 - -

No.2 Shielded room 4659A-2 3.6 x 2.7 x 2.3 - -

No.3 Shielded room - 5.4 x 3.6 x 2.3 - -

No.4 Shielded Room - 6.1 x 6.1 x 3.1 - -

No.5 Shielded Room 4659A-5 4.2 x 3.1 x 2.5 - -

No.3 Fully Anechoic Chamber - 7.0 x 3.5 x 3.5 - -

No.6 Semi-anechoic Chamber 4659A-6 8.5 x 5.5 x 5.2 - 3 m



No.1 Measurement room - 5.0 x 3.7 x 2.6 - -

No.2 Measurement room - 4.3 x 4.4 x 2.7 - -

No.3 Measurement room - 4.3 x 4.4 x 2.7 - - 3.6 Test data, Test instruments, and Test set up Refer to APPENDIX.



SECTION 4: Operation of E.U.T. during testing 4.1 Operating Mode(s)

Mode Remarks* Bluetooth (BT) Low Energy (LE) 1 Mbps Maximum Packet Size, PRBS9 Bluetooth (BT) Low Energy (LE) 2 Mbps Maximum Packet Size, PRBS9 ANT 1 Mbps 1 Mbps Nordic Original 2 Mbps 2 Mbps *Power of the EUT was set by the software as follows;Power settings: +4 dBm 10_BLE_TEST_tool-BT5 (for BT LE mode) Radio_test_tool_20180709 (for ANT and Nordic Original mode except receiver blocking test) Blocking_tool (for receiver blocking test) *This setting of software is the worst case. Any conditions under the normal use do not exceed the condition of setting. In addition, end users cannot change the settings of the output power of the product.

*The details of Operating mode(s)

Test Item Operating Mode Tested frequency RF output power, Power Spectral Density

Transmitting (Tx) BT LE 1 Mbps Transmitting (Tx) BT LE 2 Mbps

2402 MHz 2440 MHz 2480 MHz

Transmitting (Tx) ANT 1 Mbps Transmitting (Tx) Nordic Original 2 Mbps

2402 MHz 2441 MHz 2480 MHz

Occupied channel bandwidth, Transmitter unwanted emissions in the out-of-band domain

Transmitting (Tx) BT LE 1 Mbps Transmitting (Tx) BT LE 2 Mbps Transmitting (Tx) ANT 1 Mbps Transmitting (Tx) Nordic Original 2 Mbps

2402 MHz 2480 MHz

Receiver blocking

Communication, ANT 1 Mbps *1)

2402 MHz 2480 MHz

*1) Test mode was selected according to the test report: 11818213M-R1.

Extreme test condition Temperature -40 deg. C to +105 deg. C : operating temperature range of EUT Voltage Vnom: DC 3.0 V



4.2 Configuration and peripherals Other than Receiver blocking test

* Cabling and setup(s) were taken into consideration and test data was taken under worse case conditions. Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remark

A Bluetooth low energy / ANT Module

EYSLSN 81*1)82*2)

TAIYO YUDEN EUT

B Evaluation Board TE8817 - TAIYO YUDEN - C Laptop PC CF-T2 4CKSA46826 Panasonic - D AC Adaptor CF-AA1625A 1625AM406Z21913F Panasonic -

*1) Used for BT LE 1 Mbps and BT LE 2 Mbps *2) Used for ANT 1 Mbps and Nordic Original 2 Mbps List of cables used No. Name Length (m) Shield Remark

Cable Connector 1 USB Cable 1.8 Shielded Shielded - 2 DC Cable 0.5+2.0 Unshielded Unshielded - 3 DC Cable 1.2 Unshielded Unshielded - 4 AC Cable 0.8 Unshielded Unshielded -

C

1

GND

2

DC 3 V

A

AC 100 V / 50 Hz

D

3 4

B



Receiver blocking test

* Cabling and setup(s) were taken into consideration and test data was taken under worse case conditions. Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remark

A Bluetooth low energy / ANT Module

EYSLSN Rx TAIYO YUDEN EUT

B Laptop PC CF-T2 4CKSA46826 Panasonic -C AC Adaptor CF-AA1625A 1625AM406Z21913F Panasonic -D Evaluation Board TE8817 - TAIYO YUDEN -E Bluetooth low energy /

ANT Module EYSLSN Tx TAIYO YUDEN -

F Evaluation Board TE8817 - TAIYO YUDEN - List of cables used No. Name Length (m) Shield Remark

Cable Connector 1 USB Cable 1.8 Shielded Shielded - 2 DC Cable 0.5+2.0 Unshielded Unshielded - 3 DC Cable 1.2 Unshielded Unshielded - 4 AC Cable 0.8 Unshielded Unshielded - 5 USB Cable 1.5+2.0 Shielded Shielded - 6 DC Cable 0.5 Unshielded Unshielded -

B

1 2DC 3 V

AC 100 V / 50 Hz

C

3 4

D

A

F

E

5 6DC 3 V



SECTION 5: Antenna Terminal Conducted Tests Test Procedure The tests were made with below setting connected to the antenna port.

The test results are rounded off to two decimals place, so some differences might be observed. The equipment and cables were not used for factor 0.0 dB of the data sheets. Test data : APPENDIX Test result : Pass

Test Instrument used RemarkRF Output Power Power Meter Normal and Extreme conditionsPower Spectral Density Spectrum Analyzer Normal conditionOccupied Channel Bandwidth

Spectrum Analyzer Normal condition

Transmitter unwanted emissions in the out-of band domain

Spectrum Analyzer Normal conditions- Detector mode: RMS - Trace: Max Hold - Band power was used on behalf of the time domain power function. - Filter mode: Gaussian Filter Since the data in this test report has enough margin

Receiver Blocking Spectrum Analyzer Normal condition



APPENDIX 1: Test data

RF Output Power

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 July 27, 2018 Temperature / Humidity 25 deg. C / 50 % RH 24 deg. C / 47 % RH Engineer Kazuya Noda Kazuhiro Ando Mode Tx

BT LE 1 Mbps Receiver Category : 2

Freq. P/M (AV) Cable Atten. Antenna Result Limit MarginTemp. Volt. Reading Loss Loss Gain

[MHz] [dBm] [dB] [dB] [dBi] [dBm] [dBm] [dB]2402.0 -7.70 1.72 9.82 -3.70 0.14 20.00 19.862440.0 -7.66 1.73 9.82 -3.70 0.19 20.00 19.812480.0 -7.75 1.74 9.82 -3.70 0.11 20.00 19.892402.0 -6.83 1.72 9.82 -3.70 1.01 20.00 18.992440.0 -6.77 1.73 9.82 -3.70 1.08 20.00 18.922480.0 -6.86 1.74 9.82 -3.70 1.00 20.00 19.002402.0 -8.55 1.17 10.12 -3.70 -0.96 20.00 20.962440.0 -8.40 1.19 10.12 -3.70 -0.79 20.00 20.792480.0 -8.48 1.18 10.12 -3.70 -0.88 20.00 20.88

Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain

Test Condition

nom nom

min

max nom

nom

BT LE 2 Mbps Receiver Category : 2




Test Condition

max nom

nom nom

min nom



RF Output Power

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 July 27, 2018 Temperature / Humidity 25 deg. C / 50 % RH 24 deg. C / 47 % RH Engineer Kazuya Noda Kazuhiro Ando Mode Tx

ANT 1 Mbps Receiver Category : 2




nom

Test Condition

max nom

nom nom

min

Nordic Original 2 Mbps Receiver Category : 2Freq. P/M (AV) Cable Atten. Antenna Result Limit Margin

Temp. Volt. Reading Loss Loss Gain[MHz] [dBm] [dB] [dB] [dBi] [dBm] [dBm] [dB]2402.0 -7.67 1.72 9.82 -3.70 0.17 20.00 19.832441.0 -7.64 1.73 9.82 -3.70 0.21 20.00 19.792480.0 -7.73 1.74 9.82 -3.70 0.13 20.00 19.872402.0 -6.77 1.72 9.82 -3.70 1.07 20.00 18.932441.0 -6.71 1.73 9.82 -3.70 1.14 20.00 18.862480.0 -6.82 1.74 9.82 -3.70 1.04 20.00 18.962402.0 -8.64 1.17 10.12 -3.70 -1.05 20.00 21.052441.0 -8.52 1.19 10.12 -3.70 -0.91 20.00 20.912480.0 -8.59 1.18 10.12 -3.70 -0.99 20.00 20.99


min nom

Test Condition

max nom

nom nom



Power Spectral Density

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx

BT LE 1 MbpsCh S/A S/A RF Output Result Limit Margin

Temp. Volt. Freq. Maximum Total Power PowerReading Reading

[MHz] [dBm/MHz] [dBm] [dBm] [dBm/MHz] [dBm/MHz] [dB]2402.00 -7.31 -7.24 0.14 0.07 10.00 9.932440.00 -7.77 -7.70 0.19 0.12 10.00 9.882480.00 -7.82 -7.75 0.11 0.04 10.00 9.96

Result [dBm/MHz] = S/A Maximum Reading [dBm/MHz] - S/A Total Power Reading [dBm] (*1) + RF Output Power [dBm] (*2)

(*1) Integrated value of 2400 MHz to 2483.5 MHz

(*2) Refer to RF Output Power

Test Condition

nom nom

BT LE 2 Mbps

Ch S/A S/A RF Output Result Limit MarginTemp. Volt. Freq. Maximum Total Power Power

Reading Reading[MHz] [dBm/MHz] [dBm] [dBm] [dBm/MHz] [dBm/MHz] [dB]

2402.00 -9.24 -8.08 0.16 -0.99 10.00 10.992440.00 -10.06 -8.90 0.21 -0.95 10.00 10.952480.00 -10.30 -9.12 0.12 -1.06 10.00 11.06




Test Condition

nom nom

ANT 1 Mbps



2402.00 -6.45 -6.42 0.14 0.12 10.00 9.882441.00 -6.92 -6.89 0.20 0.18 10.00 9.822480.00 -7.02 -7.00 0.10 0.08 10.00 9.92




Test Condition

nom nom

Nordic Original 2 Mbps



2402.00 -7.56 -7.20 0.17 -0.18 10.00 10.182441.00 -7.55 -7.19 0.21 -0.15 10.00 10.152480.00 -7.66 -7.31 0.13 -0.23 10.00 10.23




Test Condition

nom nom



Occupied Channel Bandwidth

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 1 Mbps

Frequency Bandwidth Result Limit[MHz] [MHz] [MHz] [MHz]2402 1.0481 2401.4760 > 24002480 1.0526 2480.5263 < 2483.5

Tx 2402 MHz Tx 2480 MHz




Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 2 Mbps


Tx 2402MHz Tx 2480MHz




Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx ANT 1 Mbps


Tx 2402MHz Tx 2480MHz




Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx Nordic Original 2 Mbps


Tx 2402 MHz Tx 2480 MHz



Transmitter unwanted emissions in the out-of-band domain

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx

BT LE 1 MbpsFrequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks

Reading Loss Loss Gain[MHz] [dBm/MHz] [dB] [dB] [dBi] [dBm/MHz] [dBm/MHz] [dB]2398.5 -61.61 1.72 9.82 -3.70 -53.77 -20.00 33.77 Lowest ch 2400 MHz - 2 BW2399.5 -56.72 1.72 9.82 -3.70 -48.88 -10.00 38.88 Lowest ch 2400 MHz - BW2484.0 -61.91 1.74 9.82 -3.70 -54.05 -10.00 44.05 Highest ch 2483.5 MHz + BW2485.1 -64.13 1.74 9.82 -3.70 -56.27 -20.00 36.27 Highest ch 2483.5 MHz + 2 BW

BT LE 2 MbpsFrequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks


ANT 1 MbpsFrequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks


Nordic Original 2 MbpsFrequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks



*Above test result was maximum value on each 1 BW.



Receiver Blocking

Report No. 12406766S Test place Shonan EMC Lab. No.5 Shielded Room Date July 25, 2018 Temperature / Humidity 26 deg. C / 52 % RH Engineer Shiro Kobayashi Mode Communication, ANT 1 Mbps

Lowest Channel Highest ChannelPmin -77.91 -82.40

Pmin + 6 dB -71.91 -76.40

Receiver Category 2 equipment

2380 0.022503.5 0.012300 0.03

2583.5 0.012380 0.03

2503.5 0.012300 0.06

2583.5 0.02

*Pmin is the minimum level of wanted signal (in dBm) required to meet the minimum performance criterion a PER less than or equal to 10 % in the absence of any blocking signal.*The test was performed Blocking signal power levels corrected by the actual antenna assembly gain.

ResultPER(%)

LimitPER(%)

≦10

≦10

Pmin + 6 dB -47

Pmin + 6 dB -57

Pmin + 6 dB -57

Pmin + 6 dB -47

HighestChannel

Wanted signal meanpower from

companion device(dBm)

MeasuredReceiver Sensitivity

(corrected by the actual antenna assemblygain)

OperatingChannel

Wanted signal meanpower from

companion device(dBm)

Blocking signalfrequency

(MHz)

Blocking signal power(dBm) *1)

LowestChannel

*1) Blocking signal power was adjusted by assumed antenna gain 0.0 dBi since it was more severe condition.



Receiver Blocking ｄCONDUCTED METHODS SYSTEM BLOCK DIAGRAM of Receiver Blocking

PC Competitor

Power Splitters/ Combiners

Signal Generator

EUT Step Attenuator



APPENDIX 2: Test instruments Test Instruments

Control No.

Instrument Manufacturer Model No Serial No Test Item Calibration Date * Interval(month)

KSA-08 Spectrum Analyzer Agilent E4446A MY46180525 RB 2017/10/10 * 12

SCC-G14 Coaxial Cable Suhner SUCOFLEX 102 31600/2 AT 2018/03/19 * 12

SAT10-14 Attenuator Weinschel Corp. 54A-10 81595 AT 2018/04/20 * 12

SOS-09 Humidity Indicator A&D AD-5681 4061484 AT,RB 2017/12/21 * 12

KTS-07 Digital Tester SANWA PC500 7019232 AT,RB 2017/10/11 * 12

SPM-08 Power Meter DARE!! Instruments RPR3006W 15I00041SNO73 AT 2017/08/21 * 12

SSG-01 Signal Generator Agilent E4438C MY47271584 RB 2018/04/19 * 12

SCC-G34 Coaxial Cable Junkosha MWX241-01000KM

SKMS/B

1612Q032 RB 2018/01/25 * 12


SKMS/B

1612Q033 RB 2018/01/25 * 12


SKMS/B

1612Q034 RB 2018/01/25 * 12


SKMS/B

1612Q035 RB 2018/01/25 * 12

SPSC-02 Power

Splitters/Combiners

Mini-Circuits ZFSC-2-10G+ - RB 2018/04/20 * 12

SSAT-01 Step Attenuator KEYSIGHT 8494B MY42157639 RB 2018/02/07 * 12

SSAT-02 Step Attenuator KEYSIGHT 8496B MY42151198 RB 2018/02/07 * 12

CCH-04 Temperature and

Humidity Chamber

ESPEC PL-1J 15004059

AT 2018/07/09 * 12

CPM-16 Peak Power Analyzer AGILENT 8990B MY51000276 AT 2018/06/20 * 12

CPSO-24 Power Sensor AGILENT N1923A MY54070024 AT 2018/06/20 * 12

CAT10-16 10dB Fixed Atten WEINSCHEL 54A-10 56246 AT 2018/05/21 * 12

CCC-G13 Microwave Cable Huder + Suhner SF102/SKm/SKm/10

00mm

801389 AT 2018/07/25 * 12

CTS-18 Digital Multimeter Fluke Corporation 31837 85220051 AT 2017/09/11 * 12

COS-11 Temperature

Humidity &

Atmospheric Logger

T&D TR-73U F806046B AT 2018/05/28 * 12

The expiration date of the calibration is the end of the expired month. All equipment is calibrated with valid calibrations. Each measurement data is traceable to the national or international standards. As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibrations. Test item: AT: Antenna Terminal Conducted test RB: Reciever blocking test



APPENDIX 3: Photographs of test setup

Antenna terminal conducted tests other than Receiver Blocking

(Shonan EMC Lab.)



Receiver Blocking

End of Report

test report no. : 12406766s · non-radio test related requirements. (if applicable) 6. the all test...

Documents