Standard Specifications Export

MACK

Mack Trucks, Inc.,, Allentown, Pennsylvaniawww.macktrucks.com

ENGINE: MACK MP8-345CPeak Horsepower – 345HP at 1400 - 1800 RPMHorsepower – 308 HP at 1950 Gov. RPMMax. Torque – 1360 lb/ft at 1200 RPMV-MAC IV – Total Vehicle ElectronicsAir Compressor – Meritor/WABCO 636 (37.4 cfm)Air Cleaner, 17”x23” Oblong Style Plastic DonaldsonAlternator, Leece Neville 12V 200ABatteries, (3) Mack 12V M/F Group – 650 CCA

Total 1950 CCA Threaded Stud Type TerminalsCoolant Protection – Texaco Long Life Engine CoolantAuxiliary Cooler – 4 Fan, Left Side BOCEngine Brake – Mack PowerleashSilicone Engine Hoses and TubingSingle Vertical Exhaust w/Curved StackPoly-V Fan Belt w/Automatic TensionerFan Drive, Electronically Modulated TypeFlywheel Housing, AluminumFuel Water SeparatorTurbocharger Heat ShieldSilicone Radiator & Heater HosesStarter, 12V Gear ReductionElectronic Starter Interlock

CLUTCH: EATON/FULLER, CL798115.5” Two-Plate w/Dampened Ceramic Coax9-Spring 6-Paddle Driven Disc & 2” Diameter Spline

TRANSMISSION: MACK TM3088-Speed, Ratios: 17.77 Low – 0.71 HighPTO Side Gears (LH and RH)Driveline: Meritor 17N HD w/Coated Splines

CAB: CA531 LOW PROFILE COEAir Restriction Monitor, Graduated Lock Up Type

Air Cleaner Intake MountedAsh Tray w/Hinged CoverCab Mounting, Four Point Fixed Type Cab Tilt, Pump Mounted on RH Fender BracketCigar LighterCoat Hook, (1) Doors, Fiberglass

Sliding Type Side WindowsScreened Vent in LH DoorPeep Window in RH Door

Engine Shutoff – Key Type ControlFront Fenders, PolyurethaneFloor Mat, Rubber w/Closed Cell Vinyl Nitrile BackingMetric GaugesDual Air Pressure GaugeVoltmeterEngine Coolant Temperature GaugeEngine Oil Pressure GaugeFuel Level GaugeSpeedometer w/Trip Odometer Tachometer w/Hourmeter

• Low COE• Maneuverability• Panoramic View• Tight Wheel Cuts

Engine: MACK MP8-345C345 HP [257 kW] Peak Horsepower

Transmission: MACK TM308 8-Speed

Front Axle: MACK FXL12 12,000 lb. [5 443 kg] Capacity

Rear Axle: MACK S38R 38,000 lb. CapacitySuspension: Mack Multileaf 38,000 lb. Rated

®

The low-profile TerraPro Elite was created specificallyfor the severe service refuse industry, however, it is alsopopular in other applications such as concrete pumper,mixer/dumper and other construction equipment. Itsshort bumper back-to-back of cab dimension and set-back front axle permit effective weight distribution for onand off-road hauling. The steel cab is fully galvanized.The fiberglass doors and huge glass areas contribute toeasy entry/exit and panoramic visibility. The TerraProElite is literally designed around the task.

TerraPro6x4

STANDARD SPECIFICATIONS(Continued)

TerraPro 6x4 ExportSERIES

CAB: CA531 LOW PROFILE COE (Continued)Safety Tinted Windshield Side and Rear WindowsGrab Handles, Aluminum RH & LH Behind DoorHeater w/Integral DefrosterHorn, (1) Twin Trumpet Mounted Under Cab

Single Tone ElectronicIdentification and Clearance Lights – 7TMC Recommended Instrument PanelInterior Trim: Slate Gray VinylKeys, 2 – Keyed at RandomLow Air Pressure Indicator Light and BuzzerExterior Mirrors, RH & LH Bright Finish Mack

Bulldog w/Stainless Steel Arms and BracketsMud Flaps – 12” Front Fender MountedParking Brake Control w/Warning LightRadio Accommodation Package

Includes: Antenna, Power Supply and 2 SpeakersCB – 5 way Binding PostRear Window, FixedSeating:

Driver – Bostrom Talladega 905 Mid-BackAir Suspension

Rider – Mack Fixed Mid-Back Non-SuspensionSeat Covering, VinylSet Belts, Lap and Shoulder w/Locking Seat Belt

Retractors “Komfort Latch” for Driver andRider Seats

Side Markers – Lamps and ReflectorsKey Type StarterSteering Column, FixedSteering Wheel, Two Spoke Urethane Grip Painted

Spokes and Bulldog Horn CapForward Overhead Storage (2) Sun Visor, Interior Both Sides Turn Signal Switch, Manual CancellingWindshield Corner Wind DeflectorWindshield Washers, Wiper Mounted with 7qt

ReservoirWindshield Wipers: Electric Motor w/Intermittent

Feature

FRAME:Wheelbase (WB) – 173”Load Platform (LP) – 273”Cab to Axle (CA) – 170”Axle to End of Frame (AF) – 103”Frame Rails – Steel Cross Section – 13.25 x 3.25” x .3125”Section Modulus, 26.06 in3

RBM (per rail) – 3,127,200 lb. in.Bumper: Extended Swept Back Steel Channel TypeBumper to Back of Cab (BBC) – 63”Crossmembers: 1/2” Plate Type Bolted Back of Cab

Intermediate 1/8” Below Top of RailFront Tow PinInside Channel Reinforcement

FUEL TANKS:Capacity/Location: 70 Gallon RH Steel, 24” Diameter

FRONT AXLE: MACK FXL1212,000 lb. CapacityTires: 11R22.5 SinglesWheel Equipment: (2) 22.5 x 8.25 Steel Disc

10-Hole Hub PilotedBrakes: Meritor “S” Cam 16.5”x 5” Q-Plus w/o Dust ShieldsBrake Drums Cast Outboard MountedSlack Adjusters – AutomaticSuspension:

Mack Multileaf 12,000 lb. Ground Load RatingSteering: 392S Sheppard Integral Power Steering

REAR AXLE: S38R38,000 lb CapacityCarrier – Malleable CRDPC92/CRD93Suspension – SS38 Mack Multileaf 38,000 lb CapacityTires: 11R22.5 DualsWheel Equipment: (8) 22.5 x 8.25 Steel Disc

10-Hole Hub PilotedBrakes: Meritor “S” Cam 16.5”x 7” Q-Plus w/o Dust ShieldsBrake Drums Cast Outboard MountedWheel Seals – OilSlack Adjusters – AutomaticSpring Brake Chambers:

(4) 30/30 Double Diaphragm Type Mechanical Spring Release

Trunnion Bushing

AIR/BRAKE:Dual Air Brake SystemDual Air Dryer w/Cooling TankAir Reservoirs – Steel 5100 in3 Capacity

ELECTRICAL:Battery Box - Molded Plastic w/Locking Tab Electric Circuit Protection Package

12V w/Circuit BreakersNegative Ground System

Waterproof Electrical ConnectionsControl Link w/typical Refuse Bodybuilder

Interface ConnectionsHeadlamps – (2) Single Round Halogen LampsRear Lighting – (2) Combination Stop, Tail Directional and

Back-Up LightsTransistorized Turn Signal

PAINT:Cab, Hood and Fenders:

Mack White (High Gloss)Urethane Base Coat w/o Clear Coat

Chassis Running Gear:Mack Black (Urethane)

WEIGHT:Front: 9,629Rear: 6,935TOTAL: 16,564

SERIESTerraPro 6x4Export

(All measurements are in inches)CHASSIS SPECIFICATIONS

AVAILABLE DRIVELINE COMPONENTS

15.39

273 LP

170 CA 103 AF

61.6

75.6

13.25 10.62

42.2 unloaded40.9 loaded

173 WB54.6

3.5

4.75

103.2

95.4

33.38

60°

63 BBC

25

22

AXLES

CAPACITY MAKE MODELFRONT AXLES

12,000 lb.[5 443 kg]

MACK FXL12

14,600 lb.[6 623 kg]

MACK FXL14.6

18,000 lb.[8 165 kg]

MACK FXL18

20,000 lb.[9 072 kg]

MACK FXL20

23,000 lb.[10 400 kg]

MACK FXL23

REAR AXLES

38,000 lb.[17 237 kg]

MACK S38R/SB38

44,000 lb.[19 958 kg]

MACK S440

46,000 lb.[20 886 kg]

MACK S440-46/S462

MERITOR RT46-160

52,000 lb.[23 600 kg]

MACK S522

58,000 lb.[26 309 kg]

MACK S582

TRANSMISSIONS

MODEL SPEEDS RATIOS(LOW/HIGH)

MACKTM308 8 17.77/0.71

TM308M 8 17.77/0.71

TM309 9 25.21/0.71

TM309M 9 25.21/0.71

T309 9 11.40/0.71

T309(LR) 9 13.93/0.71

T310 10 13.81/0.73

T310M 10 17.35/0.73

T310ME 10 17.35/0.73

ALLISON4500 RDS 5 4.70/0.76

4500 RDS 6 4.70/0.67

ALLISON—FOR FIRE PUMPER SERVICE4000 EVS 5 3.51/0.74

4500 EVS 5 4.70/0.67

4000 EVS 6 3.51/0.64

4500 EVS 6 4.70/0.67

EATON FULLERRTO-14908LL 10 14.56/0.74

(subject to change depending on Air Cleaner)

MP8—ENGINESMODEL HORSEPOWER

MACK

MP8-345C345 HP [257 kW] @ 1400-1800 RPM

308 HP [230 kW] @ 1950

MP8-360C360 HP [269 kW] @ 1400-1800 RPM

323HP [241 kW] @ 1950

MP8-400C400 HP [298 kW] @ 1400-1800 RPM

358 HP [267 kW] @1950

OPTIONAL EQUIPMENTSERIES

A SALES ENGINEERING PUBLICATION

TerraPro 6x4 Export

©2008 Mack Trucks, Inc. CHA152 002 5030_09B 02/15/08 Printed in U.S.A.

The information in this brochure was accurate as known as of the date of the publication.Illustrations may not be representative of current product. Mack Trucks, Inc. reserves theright to make changes in specifications, equipment or design, or to discontinue modelsor options without notice at any time.

FRAME:Optional Frames without ReinforcementRail Dimensions: 13.25” x 3.25” x .31” Section Modulus: 19.79 in3

Resistance Bending Moment (RBM) 2,374,800 lbs. in.

Rail Dimension: 13.37” x 3.25” x .37Section Modulus: 23.49 in3

Resistance Bending Moment (RBM) 2,818,800 lbs. in.

Optional Frames with ReinforcementRail Dimension: 13.37” x 3.25” x .37Section Modulus: 29.42 in3

Resistance Bending Moment (RBM) 3,530,4000 lbs. in.

Wheelbase Availability: 159” to 220”

OTHER OPTIONAL EQUIPMENT:Air Cleaner – 15”, Single ElementAir Conditioning – Integral Combo UnitAir Horn OptionsAlternator - 12V 200A Aluminum Air ReservoirsBack-Up AlarmBattery Disconnect SwitchBattery OptionsEngine Block Heater OptionsEngine Starting AidFront Fender Mounted Mud Flaps 24”Front Frame ExtensionFuel HeaterGauge Options:

Exhaust Pyrometer GaugeManifold Pressure GaugeMetricTransmission Oil Temperature

Hand Control ValveHubodometerIncandescent Single Round HeadlightsKeyed Alike Chassis

LH Fuel TankLube Pump and FilterMirror OptionsOil Pan HeaterOverhead Storage OptionsPersonalized Name PlatePower Divider LockoutPower Take Off OptionsPush Button StartRear Crossmemeber, I-BeamRear Lighting OptionsRear View Camera Prep KitSeating and Seat Covering OptionsSkid PlateStarter – Delco 12V MTDH 39Static Load Cushions – Front AxleStereo Cassette/Stereo CD Radio OptionsSynthetic LubricantsWheel Equipment: Spoke, Steel or Aluminum DiscWheel LugwrenchWindshield Protector

OTHER COMPONENT OPTIONS MAY BEAVAILABLE UPON REQUEST