temporizator start stop
DESCRIPTION
Electronic projectTRANSCRIPT
K2579
ILLUSTRATED ASSEMBLY MANUAL H2579IP-2
Total solder points: 62 Difficulty level: beginner 1 2 3 4 5 advanced
Small size timer provides up to
60 minutes delay.
UNIVERSAL START/STOP TIMER
Specifications
Relay output with switchover contact. Power supply : 12VDC regulated. Typical active current : 55mA. Relay output : 2A/240V max. Dimensions : 35x70mm / 1.37x2.75"'
H2579IP'1_rev3.pubpage 1
Tuesday, May 22, 2012 15:06
VELLEMAN NV Legen Heirweg 33
9890 Gavere Belgium Europe
www.velleman.be www.velleman-kit.com
H2579IP'1_rev3.pubpage 2
Tuesday, May 22, 2012 15:06
3
The K2579 is a basic timer with relay output for time intervals of up to 15 minutes. Set the desired delay with the trimmer. The maximum delay can easily be lengthened and the timer can be stopped and restarted at any time. Features Start / stop push buttons included. LED status indicator. Timing adjustable from a few seconds to 15 minutes, extendable to 60 minutes. Relay output with switchover contact. Specifications : Power supply : 12VDC regulated. Typical idle current : 20mA. Typical active current : 55mA. Relay output : 2A/240V max. Dimensions : 35x70mm / 1.37x2.75"'
Features & Specifications
H2579IP'1_rev3.pubpage 3
Tuesday, May 22, 2012 15:06
Assembly hints
1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip,
and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any flux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes, the values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0.000
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint
H2579IP'1_rev3.pubpage 4
Tuesday, May 22, 2012 15:06
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST!
REMOVE THEM FROM THE TAPE ONE AT A TIME !
H2579IP'1_rev3.pubpage 5
Tuesday, May 22, 2012 15:06
6
R1 : 1K (1 - 0 - 2 - B) R2 : 10K (1 - 0 - 3 - B) R3 : 4K7 (4 - 7 - 2 - B) R4 : 1K (1 - 0 - 2 - B) R5 : 10K (1 - 0 - 3 - B) R6 : 4K7 (4 - 7 - 2 - B) R7 : 1K (1 - 0 - 2 - B)
2. Resistor R...
Construction
D1 : 1N4148
1. Diode. Watch the polarity !
D...CATHODE
RV1 : 2M2
5. Trim potentiometer
IC : 8p.
3. IC socket. Check the position of the notch!
C1 : 100nF
4. Capacitor
C...
T1 : BC547B
6. Transistor
C2 : 100µF
7. Electrolytic Capacitor. Watch the polarity !
LD1 : 5mm RED
8. LED. Check the polarity!
LD...
COLOR = 2...5
CATHODE
C...
H2579IP'1_rev3.pubpage 6
Tuesday, May 22, 2012 15:06
7
Construction
SW1 : START SW2 : STOP
9. Push buttons
RY : VR15M121C
10. Relay
RY...
IC : NE555
11. IC. Check the position of the notch!
H2579IP'1_rev3.pubpage 7
Tuesday, May 22, 2012 15:06
8
12. Connection example
Connection example
220nF/400V
100E/1WA B or C
Snubber network*
*see hook-up and use
NC
NO
AB
CCOM12V DC
300 mA
H2579IP'1_rev3.pubpage 8
Tuesday, May 22, 2012 15:06
9
Hook-up and use
Connect the unit with a 12VDC regulated power supply as shown in the example. Turn the trimmer all the way counterclockwise. Push the START button. The relay will be activated momentarily. The position of the trimmer determines the ON-time. Turn it clockwise to increase the ON-time. Increase the value of C2 for an even longer activation duration. The unit can be stopped at any time by pressing the STOP button. The START and STOP buttons can be mounted in a remote location. Make sure to use screened cable,
avoid outside interference and keep the distance between the switches and the PCB as short as possible. The timer is equipped with a relay output that is galvanically separated from the rest of the circuit for extra
safety. The connection example lists the function of the pins of the relay contacts. If the relay is used to switch important inductive loads, such as electric motors or transformers, it may be
necessary to install a snubber network across the relay contacts to avoid excessive contact wear. Ensure that the power supply of the circuit is sufficiently HF decoupled. Noise impulses entring
trough the power supply may start and stop the circuit unnecessarily.
13. Hook-up and use
H2579IP'1_rev3.pubpage 9
Tuesday, May 22, 2012 15:06
10
10. PCB layout.
PCB
14. PCB layout.
H2579IP'1_rev3.pubpage 10
Tuesday, May 22, 2012 15:06
11
CTL 5
GN
D1
OUT 3RS
T4
THR6 TRIG2
DISC7 VC
C8
IC1
NE555
R64K7
R41K
R34K7
R1
1K
R210K
RV12M2
C2100µ
T1BC547
R5
10K
RYVR15M211C
D11N4148
SW2 SW1
A
B
C
POWER +12V
GND
GND
GND
LD1LED
R71K
C1100n
GND
15. Diagram
Diagram
H2579IP'1_rev3.pubpage 11
Tuesday, May 22, 2012 15:06
5 4 1 0 3 2 9 3 1 1 3 8 4Modifications and typographical errors reserved - © Velleman nv. H2579P - 2012 - ED2 (rev.3)
Learn how to connect your computer with the outside world, master the USB communication with tutorial examples. Play with LED indicators and learn how to drive LCDisplays.
This board with different signals will teach you how to use an oscilloscope. Optimized instructions for use of our HPS140 oscilloscope. YouTube demo movies.
Fun solar powered projects. Learn all about solar energy.
EXPERIMENT KIT SOLAR ENERGY EDUKIT SCOPE
TUTOR BOARD USB
Learn how to solder, build different exciting projects. Includes spare components and demo boards.
STARTER BOX SOLDER EDUCATIVE
The EDU01 basic experiment kit is the first step into the world of modern electronics. Build your own circuits in a fun, safe and educative way.
EDUCATIVE STARTERBOX SOLDERLESS
03
02
01
06
05
Enter the world of microcontroller programming, easy step by step instructions. Includes programmer and test board.
TUTOR KIT PICTM 10
H2579IP'1_rev3.pubpage 12
Tuesday, May 22, 2012 15:06