temp range: -20ºc-+50ºc pout=1x(96-288)w master...

Important: Read all instructions prior to installation.

Wireless LED RGB Wall Switchfor EZ Dimmer Series Controllers

1 - 868MHz RGB LED Dimmer Wall Switch1 - 3V CR2032 Battery

Parts Included

Instructional SheetPart Number:

4400 Earth City Expy, St. Louis MO 63045 866-590-3533 [email protected]

Wall Switch

ControllerSafetySet-Up Instructions

Cove Lighting Application

Remote1. Follow illustrated steps to remove the Battery Tray. Insert the

3V battery included with the Wall Switch.Controller1. Make sure power to the Controller is disconnected.2. Using a small fl athead screwdriver, loosen the labeled

terminal screws visible on the top of the controller. 3. Matching light strip wires with labeled slots on the Controller,

insert wires and tighten terminal screws. Be sure wire conductor, not wire insulation, is secured in terminal.

4. Turn power on and wait until light strip illuminates. If it does not come on, check light strips and wiring connections.

• DO NOT install with power applied to controller.

• DO NOT expose the Wall Switch or Controller to moisture.

EZD-4C8A Controller

EZD-RGB-WM

EZD-RGB-WMController: EZD-4C8A

Power Supply Controller connected to multiple in-line LED strips

Wireless Signal to Controller

Push ON/OFF

Wall Switch

DC

INP

UT

OU

TPU

T

V+

V-

V+

R-

G-

B-

W

12/36VD

C

PairingSwitch

MASTER SLAVE

DC

INP

UT

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VD

C

PairingSwitch

MASTER SLAVE

EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC

Easy Dimmer Series


Easy Dimmer Series

EZD-RGB-WM Wall SwitchOperating Voltage 3 VDC

Battery Size CR2032Operating Frequency 868 MHz

FCC ID# 2ACUQ2836

Single PressTurns light on/off . If the receiver Controller Pairing Switch has been depressed, a single dial press on the Wall Switch pairs the Switch to the Controller.

Double Press Increases or decreases LED intensity until you release, turning LED on will remember the last memory position

Left/Right Movement During color mode, scrolls through RGB light strip colors. During dimming mode, controls LED intensity level

Hold Press Increases LEDs to maximum intensity

EZD-4C8A ControllerInput Voltage Current Output Wattage12~36 VDC 4 X 8A 384W(12V) 768W(24V)

1152W(36V)

Operating the Wall Switch/Controller1. Press “Pairing Switch” button on the Controller.

Immediately press the Wall Switch to pair it to the Controller. The LED lights wired to the Controller will blink when the pairing is complete.

2. Multiple Wall Switches can be paired to a Controller, and can be paired to multiple Controllers. If multiple Controllers paired to a Wall Switch are not in sync, unpair and then pair until Controllers and lights are in sync.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Wall Switch Instructions

2 - Mounting Screws

1. On/Off /RGB Color/Brightness Push DialPush dial for remotely activating/controlling RGB light strips.

2. Color Gradient Visual key representing the specifi c dial colors.

3. Dimming LevelVisual key representing the dial brightness level.

4. Pairing SwitchTo Pair Wall Switch to Controller, push once and then push Wall switch. Lights will blink once to indicate linking. To unpair Wall Switch(es), push and hold until lights blink twice.

5. Master/Slave JumperSet Jumper to Master for main Controller. Master emits syncronization signal to Slave Controllers. Set Jumper to Slave to receive syncronization signal from Master Controller. Use Master for the fi rst Controller in each zone. To acheive precise syncronization between Controllers in one zone, set additional Controllers to slave.

1. Pull off dial and collar from front plate.

2. Using a fl at head screwdriver, pry rear switch housing away from front plate.

3. Insert battery with tray into slot, matching the polarity on the battery with the slot labels.

4. Fasten wall switch using mounting screws.

5. Reinstall front plate, collar and dial.

1 2 3 4

Push ON/OFF

11

2

3

4

4

5

32

45

Important: Read all instructions prior to installation.

Instructional SheetPart Number:

4400 Earth City Expy, St. Louis MO 63045 866-590-3533 [email protected]

EZD-RGB-WMController: EZD-4C8A

Connection Diagram

Example Diagrams

DC

INP

UT

OU

TPU

T

V+

V-

V+

R-

G-

B-

W

12/36VD

C

PairingSwitch

MASTER SLAVE

DC

INP

UT

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VD

C

PairingSwitch

MASTER SLAVE


Easy Dimmer Series


Easy Dimmer Series

EZD-4C8A Controller

Common Anode Output (+)

Channel 2 Output (-)



(+)(-)


Pairing Switch

Master/Slave Jumper

B G R V+NC

To Additional Controllers24VDC OutFrom

PowerSupply

24VDC In


PowerSupply

12VDC In

NFLS-RGBNW300X4-24V

WBRG+

WBRG+

WBRG+

WBRG+

WBRG+

B G R V+

NFLS-RGB150X2-WHT-LC4

BRG+

BRG+

BRG+

BRG+

BRG+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series


PowerSupply

12VDC In

NFLS-B300-WHT-LC2

NFLS-G300-WHT-LC2

NFLS-R300-WHT-LC2

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

B G R V+NC


PowerSupply

24VDC In


PowerSupply

12VDC In

NFLS-RGBNW300X4-24V

WBRG+

WBRG+

WBRG+

WBRG+

WBRG+

B G R V+


BRG+

BRG+

BRG+

BRG+

BRG+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series


PowerSupply

12VDC In

NFLS-B300-WHT-LC2

NFLS-G300-WHT-LC2

NFLS-R300-WHT-LC2

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

B G R V+NC


PowerSupply

24VDC In


PowerSupply

12VDC In

NFLS-RGBNW300X4-24V

WBRG+

WBRG+

WBRG+

WBRG+

WBRG+

B G R V+


BRG+

BRG+

BRG+

BRG+

BRG+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series


PowerSupply

12VDC In

NFLS-B300-WHT-LC2

NFLS-G300-WHT-LC2

NFLS-R300-WHT-LC2

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

_+

DC

INPU

T

OU

TPU

T

V+

V-

V+

CH1

CH2

CH3

CH4

12/36VDC

PairingSwitch

MASTER SLAVE


Easy Dimmer Series

(1) RGB 24VDC Application / EZD-4C8A (2) RGB 12VDC Application / EZD-4C8A

(3) Seperate RGB 12VDC Application / EZD-4C8A

Power In

Wireless LED RGB Wall Switchfor EZ Dimmer Series Controllers

Note: CH1 is the Red Channel CH2 is the Green Channel CH3 is the Blue Channel CH4 is not used

temp range: -20ºc-+50ºc pout=1x(96-288)w master...

Documents