technician licensing class go picture these! valid july 1, 2014 through june 30, 2018

82
Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Upload: theodore-warren

Post on 21-Jan-2016

214 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Technician Licensing Class

Go Picture These!

Valid July 1, 2014

Through

June 30, 2018

Page 2: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2

Amateur Radio Technician ClassElement 2 Course Presentation

ELEMENT 2 SUB-ELEMENTS (Groupings)

• About Ham Radio• Call Signs• Control• Mind the Rules• Tech Frequencies• Your First Radio• Going On The Air!• Repeaters• Emergency!• Weak Signal Propagation

Page 3: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

3

Amateur Radio Technician ClassElement 2 Course Presentation

ELEMENT 2 SUB-ELEMENTS (Groupings)

• Talk to Outer Space!• Your Computer Goes Ham Digital!• Multi-Mode Radio Excitement• Run Some Interference Protection• Electrons – Go With the Flow!• It’s the Law, per Mr. Ohm!Go Picture These!• Antennas• Feed Me with Some Good Coax!• Safety First!

Page 4: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

Schematic Symbols

Page 5: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

• T6C1 Schematic symbols is the name for standardized representations of components in an electrical wiring diagram.

• T6C12 The symbols on an electrical circuit schematic diagram represent electrical components.

• T6C13 The way electrical components are interconnected accurately represent electrical circuit schematic diagrams.

Page 6: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

• T6D08 We use series and parallel inductors and capacitors to develop a tuned circuit inside your radio..

• T6D11 A resonant circuit must contain at least one inductor and one capacitor connected in series or parallel to form a filter.

Tank Circuit or Tuned Circuit

Capacitor (variable)

Inductor

Tank Circuit Schematic

Page 7: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

T6C2 Component 1 in figure T1 is a resistor.

12

3

4

5

12

3

4

5

Figure T1

Resistor

Page 8: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

88

Picture This!

• T6C02 Component #1, that squiggly line, is a resistor

12

3

4

5

12

3

4

5

Figure T1

Page 9: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

•T6C3 Component 2 in figure T1 is a transistor.

•T6D10 To control the flow of current is the function of component 2 in Figure T1.

12

3

4

5

12

3

4

5

Figure T1

Transistor

Page 10: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

•T6C4 Component 3 in figure T1 is a lamp.

12

3

4

5

12

3

4

5Figure T1

Lamp

Page 11: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

•T6C11 Component 4 in figure T3 is an antenna.

1

2

3

4

1

2

3

4

Figure T3

Antenna

Page 12: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

•T6D3 A single-pole single-throw switch is represented by item 3 in figure T2.

1

2 5

4

3

6

7

8

9

10

1

2 5

4

3

6

7

8

9

10

Figure T2

Single-Pole Single-Throw Switch

Page 13: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

1313

Picture This!

T6C09 Component #4 takes in everything around it, and is a transformer. Voltage is passed from the windings on the left, to the windings on the right, with the two vertical lines representing an iron core.

Page 14: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

1414

Picture This!

• T6C06. Component #6 has 2 parallel (sort of) plates, separated by an insulation, so it must be a capacitor.

1

2 5

4

3

6

7

8

9

10

1

2 5

4

3

6

7

8

9

10

Page 15: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

1515

Picture This!

• T6C07 See the little arrow symbols on component #8 showing the effects of light? Component # 8 is a light emitting diode – an LED. Easy

• T6C08 Component #9 is indeed a resistor, but it has a variable tap point on it, so it is a variable resistor. We’ll formally call it a potentiometer, and this could be the volume control on your handheld.

Page 16: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

1616

Picture This!

• T6D04 Your larger, high-frequency transceivers may have a mechanical meter movement to illustrate incoming signal strength. Even if it is an LED or LCD readout, we still call it a signal strength meter.

Page 17: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

T6D02 A mobile radio that puts out 50 watts will likely contain a relay. The relay is a mechanical switch, opened and closed by current passing through a coil, creating an electromagnet. As soon as the coil is energized, the switch goes from one state to another.

Electromagnets

Relays

Page 18: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

• T6D5 A regulator is a type of circuit that controls the amount of voltage from a power supply.

• T6D6 A transformer is a component commonly used to change 120V AC house current to a lower AC voltage for other uses.

• T6D9 Integrated circuit is the name of a device that combines several semiconductors and other components into one package.

Large-scale integrated circuit chips .

Voltage Regulators

Voltage Transformer

Page 19: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

•T5B09 The approximate amount of change, measured in decibels (dB), of a power increase from 5 watts to 10

watts is 3dB.

• T5B10 The approximate amount of change, measured in decibels (dB), of a power decrease from 12 watts to 3 watts is 6dB.

• T5B11 The approximate amount of change, measured in decibels (dB), of a power increase from 20 watts to 200 watts is 10 dB.

3 dB6 dB9 dB

10 dB

20 dB30 dB40 dB

2x4x8x

10x100x

1000x10,000x

Power changePower changePower changePower changePower changePower changePower change

dB Power Change

Page 20: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2020

Picture This!

• T6B07 LED stands for Light Emitting Diode, The LED draws almost no amount of current and will last for hundreds of thousands of hours without burnout. LED = Light Emitting Diode.

Page 21: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2121

Picture This!

• T6D07 A good visual indicator on a handheld radio is the LED – the light emitting diode that is often used as a transmit indicator.

• T5B02 Another way to specify a radio signal frequency of 1,500,000 Hz as 1,500 kHz, or 1.5 MHz.

• T5B13 If a frequency readout shows a reading of 2425 MHz, what frequency is that in GHz? There are 1,000 MHz in one GHz, so we can simply divide by 1000 to get the final answer, 2.425 GHz.

Page 22: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2222

Picture This!

• T5B03 Kilo means one thousand. 1000 volts equals 1 kilovolt.

• T5B06 One ampere equal 1000 milliamperes. If an ammeter calibrated in amperes is used to measure a 3000-milliampere of current, the reading would it to be 3 amperes.

• T5B12. There are a thousand Kilohertz in one Megahertz,

so 28,400 KHz is equal to 28.400 MHz

Page 23: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Picture This!

23

Metric Prefixes

1,000,000.000,000M k o m m e i n i i g l e l c a o l r e o

Page 24: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Go Picture These!

• T5B5 0.5 watts is equivalent to 500 milliwatts.• T5B1 1,500 milliamperes is 1.5 amperes.• T5B8 One microfarads is equal to 1,000,000 picofarads.• T5B4 One one-millionth of a volts is equal to one

microvolt

Metric Exponent English Tera 1012 Trillion Giga 109 Billion Mega 106 Million Kilo 103 Thousand Centi 10-2 Hundredth Milli 10-3 Thousandth Micro 10-6 Millionth Nano 10-9 Billionth Pico 10-12 Trillionth

Page 25: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2525

Picture This!

• T7D08 Rosin-core solder is commonly available at the same place you purchase your soldering iron or gun.

• A little soldering pen is fine for working on tiny circuits, but you’re going to need a massive soldering iron or a big 200 watt soldering gun if you plan to install coax connectors properly.

• Always use rosin-core solder. Wear protective glasses, too!

Page 26: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2626

Picture This!

• T7D09 It’s easy to tell if you’ve made a good solder connection – the solder looks shiny. However, a “cold,” poorly-soldered joint looks grainy and dull.

Page 27: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2727

Picture This!

• T7D07 Every amateur operator should own a multimeter. Measurements commonly made using a multimeter are voltage and resistance.

• T7D011 Any time you are checking a

circuit with an ohmmeter,

make sure the circuit is not powered!

• T7D06 You’re likely to damage your multimeter

by measuring voltage if you accidentally leave it

in the resistance setting.

Page 28: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

2828

Picture This!

• T7D010 When an ohmmeter is connected across a circuit and initially indicates a low resistance and then shows increasing resistance with time, the circuit contains a large capacitor.

Page 29: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Take Aways

Section Seventeen Take Aways

Words that are bold and red appear in the correct answer.

Page 30: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Schematic symbols are the name for standardized representations of components in an electrical wiring diagram.

The symbols on an electrical circuit schematic diagram represent electrical components.

The way components are interconnected is accurately represented in electrical circuit schematic diagrams.

A meter can be used to display signal strength on a numeric scale.

30

Take Aways

Page 31: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

12

3

4

5

12

3

4

5

Resistor

Lamp

Transistor that controls flow of current

Battery

Figure T1

31

Take Aways

Page 32: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

1

2 5

4

3

6

7

8

9

10

1

2 5

4

3

6

7

8

9

10

Figure T2

Single-Pole Single-Throw Switch

Transformer

Capacitor.

Light Emitting

Diode

Variable Resistor

32

Take Aways

Page 33: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Figure T3

1

2

3

4

1

2

3

4

A Tuned Circuit is a capacitor combined with an inductor to create a filter.

Antenna

Variable Inductor

33

Take Aways

Variable Capacitor

Page 34: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

A relay is a switch controlled by an electromagnet.

A regulator circuit controls the amount of voltage from a power supply.

A transformer is commonly used to change 120V AC house current to a lower AC voltage for other uses.

An Integrated circuit is a device that combines several semiconductors and other components into one package.

The abbreviation "LED" stands for Light Emitting Diode.

A LED is commonly used as a visual indicator.

34

Take Aways

Page 35: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Decibels (dB) measure amount of change using a logarithmic scale

An amount of change of a power increase from 5 watts to 10 watts (change factor of 2) is 3dB.

An amount of change of a power decrease from 12 watts to 3 watts (change factor of 4) is -6dB.

An approximate amount of change of a power increase from 20 watts to 200 watts (change factor of 10) is 10 dB.

3 dB6 dB9 dB

10 dB

20 dB

2x4x8x

10x100x

Power changePower changePower changePower changePower change

35

Take Aways

Page 36: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Another way to specify a radio signal frequency of 1,500,000 hertz is 1500 kHz.

One thousand volts are equal to one kilovolt.

If an ammeter calibrated in amperes is used to measure a 3000‑milliampere current, the reading shown is 3 amperes.

0.5 watts is equivalent to 500 milliwatts.

1,500 milliamperes equals 1.5 amperes.

1,000,000 picofarads is equal to 1 microfarad. 36

Take Aways

Page 37: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Another way to specify a radio signal frequency of 1,500,000 hertz is 1500 kHz.

One thousand volts are equal to one kilovolt.

A frequency of 2425 MHz is equal to 2.425 GHz. There are 1000 Megahertz in one Gigahertz.

A frequency readout of 3.525 MHz would show as 3525 kHz. There are 1,000 kiloHertz in one MegaHertz.

One one-millionth of a volt is equal to one microvolt.37

Take Aways

Page 38: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

Rosin-core solder is best for radio and electronic use.

A grainy or dull surface is the characteristic appearance of a "cold" solder joint.

Measurements commonly made using a multimeter are voltage and resistance.

38

Take Aways

Page 39: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

A precaution that should be taken when measuring circuit resistance with an ohmmeter is to ensure that the circuit is not powered.

Attempting to measure voltage when using the resistance setting might damage a multimeter.

When an ohmmeter, connected across a circuit, initially indicates a low resistance and then shows increasing resistance with time the circuit contains a large capacitor.

39

Take Aways

Page 40: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

40

Picture This!

Element 2 Technician Class Question Pool

Valid July 1, 2014

Through

June 30, 2018

Page 41: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

41

T6C01 What is the name for standardized representations of components in an electrical wiring diagram?

A. Electrical depictions

B. Grey sketch

C. Schematic symbols

D. Component callouts

Page 42: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

42

T6C12 What do the symbols on an electrical circuit schematic diagram represent?

A. Electrical components

B. Logic states

C. Digital codes

D. Traffic nodes

Page 43: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

43

T6C13 Which of the following is accurately represented in electrical circuit schematic diagrams?

A. Wire lengths

B. Physical appearance of components

C. The way components are interconnected

D. All of these choices

Page 44: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

44

T6C10 What is component 3 in figure T3?

A. Connector

B. Meter

C. Variable capacitor

D. Variable inductor

Page 45: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

45

T6C11 What is component 4 in figure T3?

A. Antenna

B. Transmitter

C. Dummy load

D. Ground

Page 46: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

46

T6D08 Which of the following is used together with an inductor to make a tuned circuit?

A. Resistor

B. Zener diode

C. Potentiometer

D. Capacitor

Page 47: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

47

T6D11 What is a simple resonant or tuned circuit?

A. An inductor and a capacitor connected in series or parallel to form a filter

B. A type of voltage regulator

C. A resistor circuit used for reducing standing wave ratio

D. A circuit designed to provide high fidelity audio

Page 48: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

48

T6C02 What is component 1 in figure T1?

A. Resistor

B. Transistor

C. Battery

D. connector

Page 49: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

49

T6C03 What is component 2 in figure T1?

A. Resistor

B. Transistor

C. Indicator lamp

D. Connector

Page 50: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

50

T6D10 What is the function of component 2 in Figure T1?

A. Give off light when current flows through it

B. Supply electrical energy

C. Control the flow of current

D. Convert electrical energy into radio waves

Page 51: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

51

T6C04 What is component 3 in figure T1?

A. Resistor

B. Transistor

C. Lamp

D. Ground symbol

Page 52: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

52

T6C05 What is component 4 in figure T1?

A. Resistor

B. Transistor

C. Battery

D. Ground symbol

Page 53: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

53

T6D03 What type of switch is represented by item 3 in figure T2?

A. Single-pole single-throw

B. Single-pole double-throw

C. Double-pole single-throw

D. Double-pole double-throw

Page 54: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

54

T6C09 What is component 4 in figure T2?

A. Variable inductor

B. Double-pole switch

C. Potentiometer

D. Transformer

Page 55: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

55

T6C06 What is component 6 in figure T2?

A. Resistor

B. Capacitor

C. Regulator IC

D. Transistor

Page 56: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

56

T6C07 What is component 8 in figure T2?

A. ResistorB. InductorC. Regulator ICD. Light emitting diode

Page 57: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

57

T6C08 What is component 9 in figure T2?

A. Variable capacitorB. Variable inductorC. Variable resistorD. Variable transformer

Page 58: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

58

T6D04 Which of the following can be used to display signal strength on a numeric scale?

A. Potentiometer

B. Transistor

C. Meter

D. Relay

Page 59: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

59

T6D02 What best describes a relay?

A. A switch controlled by an electromagnet

B. A current controlled amplifier

C. An optical sensor

D. A pass transistor

Page 60: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

60

T6D05 What type of circuit controls the amount of voltage from a power supply?

A. Regulator

B. Oscillator

C. Filter

D. Phase inverter

Page 61: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

61

T6D06 What component is commonly used to change 120V AC house current to a lower AC voltage for other uses?

A. Variable capacitor

B. Transformer

C. Transistor

D. Diode

Page 62: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

62

T6D09 What is the name of a device that combines several semiconductors and other components into one package?

A. Transducer

B. Multi-pole relay

C. Integrated circuit

D. Transformer

Page 63: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

63

T5B09 What is the approximate amount of change, measured in decibels (dB), of a power increase from 5 watts to 10 watts?

A. 2 dB

B. 3 dB

C. 5 dB

D. 10 dB

Page 64: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

64

T5B10 What is the approximate amount of change, measured in decibels (dB), of a power decrease from 12 watts to 3 watts?

A. -1 dBB. -3 dBC. -6 dBD. -9 dB

Page 65: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

65

T5B11 What is the approximate amount of change, measured in decibels (dB), of a power increase from 20 watts to 200 watts? *

A. 10 dB

B. 12 dB

C. 18 dB

D. 28 dB

Page 66: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

66

T6B07 What does the abbreviation "LED" stand for?

A. Low Emission Diode

B. Light Emitting Diode

C. Liquid Emission Detector

D. Long Echo Delay

Page 67: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

67

T6D07 Which of the following is commonly used as a visual indicator?

A. LED

B. FET

C. Zener diode

D. Bipolar transistor

Page 68: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

68

T5B02 What is another way to specify a radio signal frequency of 1,500,000 hertz?

A. 1500 kHz

B. 1500 MHz

C. 15 GHz

D. 150 kHz

Page 69: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

69

T5B13 If a frequency readout shows a reading of 2425 MHz, what frequency is that in GHz?

A. 0.002425 GHz

B. 24.25 GHz

C. 2.425 GHz

D. 2425 GHz

Page 70: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

70

T5B03 How many volts are equal to one kilovolt?

A. One one-thousandth of a volt

B. One hundred volts

C. One thousand volts

D. One million volts

Page 71: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

71

T5B06 If an ammeter calibrated in amperes is used to measure a 3000-milliampere current, what reading would it show?

A. 0.003 amperes

B. 0.3 amperes

C. 3 amperes

D. 3,000,000 amperes

Page 72: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

72

T5B12 Which of the following frequencies is equal to 28,400 kHz?

A. 28.400 MHz

B. 2.800 MHz

C. 284.00 MHz

D. 28.400 kHz

Page 73: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

73

T5B05 Which of the following is equivalent to 500 milliwatts?

A. 0.02 watts

B. 0.5 watts

C. 5 watts

D. 50 watts

Page 74: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

74

T5B01 How many milliamperes is 1.5 amperes?

A. 15 milliamperes

B. 150 milliamperes

C. 1,500 milliamperes

D. 15,000 milliamperes

Page 75: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

75

T5B08 How many microfarads are 1,000,000 picofarads?

A. 0.001 microfarads

B. 1 microfarad

C. 1000 microfarads

D. 1,000,000,000 microfarads

Page 76: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

76

T5B04 How many volts are equal to one microvolt?

A. One one-millionth of a volt

B. One million volts

C. One thousand kilovolts

D. One one-thousandth of a volt

Page 77: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

77

T7D08 Which of the following types of solder is best for radio and electronic use?

A. Acid-core solder

B. Silver solder

C. Rosin-core solder

D. Aluminum solder

Page 78: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

78

T7D09 What is the characteristic appearance of a "cold" solder joint?

A. Dark black spots

B. A bright or shiny surface

C. A grainy or dull surface

D. A greenish tint

Page 79: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

79

T7D07 Which of the following measurements are commonly made using a multimeter?

A. SWR and RF power

B. Signal strength and noise

C. Impedance and reactance

D. Voltage and resistance

Page 80: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

80

T7D11 Which of the following precautions should be taken when measuring circuit resistance with an ohmmeter?

A. Ensure that the applied voltages are correct

B. Ensure that the circuit is not powered

C. Ensure that the circuit is grounded

D. Ensure that the circuit is operating at the correct frequency

Page 81: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

81

T7D06 Which of the following might damage a multimeter?

A. Measuring a voltage too small for the chosen scale

B. Leaving the meter in the milliamps position overnight

C. Attempting to measure voltage when using the resistance setting

D. Not allowing it to warm up properly

Page 82: Technician Licensing Class Go Picture These! Valid July 1, 2014 Through June 30, 2018

82

T7D10 What is probably happening when an ohmmeter, connected across an unpowered circuit, initially indicates a low resistance and then shows increasing resistance with time?

A. The ohmmeter is defective

B. The circuit contains a large capacitor

C. The circuit contains a large inductor

D. The circuit is a relaxation oscillator