technical specification sandvik dl411-15 7-6107-a ... · the sandvik dl411-15 is an...
TRANSCRIPT
Technical Specification7-6107-A2011-06-30
Sandvik DL411-15Underground Drill Rig
1/4
© 2
011
San
dvik
Min
ing
and
Co
nst
ruct
ion
The Sandvik DL411-15 is an electro-hydraulic long-hole drilling rig for large-scale production drilling inunderground mines. The rig has been designed for vertical and inclinedplane rings and fans, parallel long production holesas well as long single holes. The 360° rotation andparallel coverage, together with wide tilt angleranges forwards and backwards, make the boomsuitable to various drilling applications.Instrumentation and data drilling with various auto-mation options allow maximum performance withsuperior drilling accuracy. Proven CAN-based tech-nology on board allows the operator to set the unitfor any rock conditions. It also makes the upgrade ofautomation level easy, and has a fault finding sys-tem, which reduces downtime. The machine is based on a proven carrier for highmobility. Tramming is done from the operator's plat-form, and drilling from a remote position next to themachine.
Carrier NC7W
Rock drill HL1560T
Boom ZR30
Drilling module LFRC1600
Control system TPC LH5
Hole diameter 89-127mm
Drilling hole length Up to 54m
Cornering 3400mm
Total weight21 000 kg(depending on options)
Technical Specification
Sandvik DL411-157-6107-A
2011-06-30
2/4
Coverage area
1995
2240
LF1600650
3000RC1600
1030
35° 35°
HR
W
WP
2 0
00
Optional
MAXIMUM DRIFT SIZE
Drilling Module
H W Wp HR
LF1604 4050 4800 3000 2100LF1605 4370 5100 3000 2100LF1606 4670 5400 3000 2100
With rear stinger in use without optional front stinger
MINIMUM DRIFT SIZE
Drilling Module
H W Wp HR
LF1604 3560 3560 1750 2100LF1605 3865 3865 2050 2100LF1606 4170 4170 2350 2100
Included 100mm clearance on each side
All dimensions in mm
Rock drill HL1560TPercussion power 33 kWPercussion pressure 200 bar maxPercussion rate 30-40 HzRotation speed 0-100 rpm (OMT500)Rotation torque Max. 2 330 Nm (OMT500)Hole size 89 - 127 mm
Recommended drill steel51-60 mm rod76-87 mm tubes
Shank adaptor T51, ST58, ST68Weight Max. 490 kgFlushing water pressure Max. 20 bar*Rock drill HL1010 instead of HL1560T*Power extractor HL1560T or HL1010
Hydraulic rock drill Technical Specification 2_1750
Boom type ZR30Parallel coverage 3000mm
Feed extensionLF1604: 1000mmLF1605: 1100mmLF1606: 1400mm
Rotation angle 360°Weight 2 800kg
Stinger extensionLF1604: 1500mmLF1605/6: 1700mm
Boom Technical Specification 4_1810
LFRC160x x=4’ / 5’ /6’Capacity 29+1 rods/tubesFeed force 31kNRod retainer Pito 16Cuttings collector CC1016*Sequence control Automatic rod/tube changing*Front stinger Required for downholes*Readiness for double tools Rods/Tubes
Drilling module
*TMS DDSDrilling direction, depth andspeed
*Uphole fan automation*One hole data drilling Automated single hole drilling
*Instrumentation options Technical Specification 5_9202
*Pressure cleaning system with reel
5-15 bar
*High pressure cleaning system with reel
Max. 180 bar
*Cleaning system
*Greasing unit with reel,pump and nozzle
Manual
*Automatic greasing system Carrier, boom and cassette
*Greasing systems and options
*Manual fire suppression system
6 nozzles
*Automatic fire suppression system
6 nozzles
*FS1000 above 0°C*Hand held fire extinguisher Operator station
*Fire suppression system and options
*Optional features/components
Technical Specification
Sandvik DL411-157-6107-A
2011-06-30
3/4
Machine dimensions
All dimensions in mm
30° 45°
1945
2100
905 15°30°
360°
325
3040
195
1425
3175
10055
L
FEED L
LF1604 3300
LF1605 3600
LF1606 3900
Filtration size20 microns (pressure)12 microns (return)
Oil coolerCooling capacity 45kWOW45 water cooling
Drilling oil tank 230 litersTank filling Electric filling pumpPowerpack HPP1590 (90kW)Percussion pump 140cc variable displacementRotation pump 71cc variable displacementBoom movements pump 28cc variable displacement*Biodegradable oils Shell Naturelle HFE68
Hydraulic system
Type TPC LH5
Power controlAdjustable full powerAdjustable collaring power
Anti-jamming controlAdjustable anti-jamming pressure
Rotation control Adjustable rotation speed
Flushing controlWater flushing flow and pressure control
Drilling control panelPortable with cable remote control
Control system
Total input power 119 kWMain switch MSE 10Standard voltages 380-690 VACStarting method Direct on lineVoltage fluctuation ±10%Cable reel TRC3ER with spoolingCable reel control Control at operator station *Star delta starter Standard for 575V and lower*Optional voltage 1000 VAC
*Electric cable rubber or PUR100m, 150m or 200mdepending on voltage
*Ground fault and over current unit
VYK
*Auxiliary outlet 230V, 16A*Remote control for reel(s) At rear end*Three phase network oulet voltage
Readiness only
*Battery jump start
Electric system
Flushing WaterWater pump WBP 2 (50Hz 7,5 kW)Water pump capacity 200 l/min (Max. 12bar)Inlet pressure 2-7 bar (while drilling)Shank lubrication Air/oil mist, SLUAir consumption 300-450l/minOil consumption 250-400g/minShank lubrication compressor CT10, 1.0m3/min (7bar)Air cleaner IP5
*CompressorCT16 (11kW, 1.6m3/min) or CT28 (18.5kW, 2.8m3/min)
*Water hose 38mm (1½”) 65 meters*Air mist flushing packages External water/air connection
Flushing system and shank lubrication
*Optional features/components
Technical Specification
Sandvik DL411-157-6107-A
2011-06-30
4/4Sandvik Mining and Construction OyP.O Box 100. FIN-33311 Tampere, FinlandTel. +358 205 44 121, Fax +358 205 44 120www.sandvik.com
Sandvik Mining and Construction reserves the right to change this specification without further notice.
© 2
011
San
dvik
Min
ing
and
Co
nst
ruct
ion
Tramming dimensions
3200
2840
2460
2950
195
3280
15°
1425
3175 2575325
17°
T
3150
40°
34005950
19
90
22
40
FEED T
LF1604 8800
LF1605 9100
LF1606 9400
All dimensions in mm
Tramming speed15 km/h on horizontal14% = 1:7 = 8° 6,5km/h
Gradeability / Inclination Max. 15° / 5°
Tramming
Safety canopy FOPS (ISO 3449)Sound pressure level according to EN791
Operator station: 102 dB(A)Emitted: 127 dB(A)
SeatErgonomic, adjustable with seat belt
Operator’s station
Front working lights 2 x 35W HID (24V) Front driving lights 2 x 35W HID (24V) Rear working lights 2 x 35W HID (24V) Rear driving lights 2 x 35W HID (24V) Parking rear brake lights 2 x Red LEDPortable working lights 2 x 35W HID (24V) Positioning lights 2 x Laser typeAmber flashing light Standard*Extra working light 2 x 35W HID (24V)
Lights
*Harsh water options (level 1) Oil cooler + boom cylinders
*Harsh water options (level 2)Level 1 + steering and jacks cylinders
*Regional AUS, USC, EUR
*Packages
Spare wheel assembly Air filledSpare wheel assembly Foam filledSpare rock drillSpecial tools for rock drill
Extra documentationPaper copiesToolman/Catbase/Link one
Extra items
Carrier name NC7WCarrier type Wheel mounted, frame steering
TransmissionHydrodynamicSpicer T20 000
Axles SpicerTyres 14.00-24Diesel engine MB904LA (110kW) Tier IIIExhaust catalyser+muffler Standard
Brakes
Service, hydraulic wet disc brakes Parking and emergency SAHR type, fail safewet disc brakes
Ground clearance 320 mmRear oscillation ± 10°Articulation ± 40°Steering Frame steeringFuel tank 150 liters
Hydraulic jacksFront frame stabilizerTJ60 (rear)
Stair and service lights LEDHand throttle StandardReverse alarm Standard*Third gear lockout*Automatic water hose reel THR2.5E*Wheel chocks 2 pieces*Fast filling system For fuel/complete*Sealed gel batteries*Foam filled tyres
Carrier
*Optional features/components