technical particular of furniture part i furniture part-i specification.pdf · technical particular...

1/81

Annexure-B

Technical Particular

Of

Furniture Part-I Recommended by Technical Specification Committee Dated

23-11-2016

2/81

Annexure-B

CSIDC/MKD/TECH/2016-17/27

THECHNICAL SPECIFICATION OF FURNITURE PART-I (TSC – 23-11-2016)

INDEX

Sl No Specification No. Item Description

Item Code Item Size Schedule -1 OFFICE & SCHOOL FURNITURE:- 1 SF19E0001 Executive Table (3 Equal Drawer & Cupboard) 1800 x 1200 x 750 mm 2 SF19E0002 Executive Table (3 Equal Drawer & Cupboard) 1800 x 900 x 750 mm 3 SF19E0003 Executive Table (3 Equal Drawer & Cupboard) 1500 x 900 x 750 mm 4 SF19E0004 Office Table (Drawer & cupboard unit) 1200 x 750 x 750 mm 5 SF19E0005 Office Table (3 Drawer) 1200 x 600 x 750 mm 6 SF19E0006 Office Table (2 Drawer) 1000 x 600 x 750 mm 7 SF19E0007 Student Table 600 x 450 x 750 8 SF19E0008 Student Chair 900 x 400 / 375 x 480 9 SF19E0009A All Steel Student Desk (Without Shelf) 900 x 425 x 750 mm 10 SF19E0009B All Steel Student Desk (With Shelf) 900 x 425 x 750 mm 11 SF19E0010 All Steel Student Bench 900 x 300 x 450 mm 12 SF19E0011 All Steel Dual Desk (Three Seater) 1500 x 900 x 750 / 450 mm 13 SF19E0012 All Steel Dual Desk (Three Seater Junior) 1150 x 900 x 750 / 475 mm 14 SF19E0013 Dual Desk (2 seater junior) 900 x 850 x 900 / 450 / 750 mm 15 SF19E0014 Dual Desk (2 seater Senior) 1050 x 900 x 900 / 450 / 750 mm 16 SF19E0015A STUDENT Desk, Angle iron frame (Without shelf) 900 x 425 x 750 mm 17 SF19E0015B STUDENT Desk, Angle iron frame (With shelf) 900 x 425 x 750 mm 18 SF19E0016 STUDENT BENCH (Angle iron frame) 900 x 300 x 450 mm 19 SF19E0017 Executive Chair (Continuous Arm) 1000/ 450 x 550 x 550 mm 20 SF19E0018 Office Chair (Fixed Back) 950/ 450 x 550 x 550 mm 21 SF19E0019 Office Chair (Flexible Back) 950/ 450 x 550 x 550 mm 22 SF19E0020 Visitor Chair (With Arm) 800/ 450 x 525 x 550 mm 23 SF19E0021 Visitor Chair (Without Arm) 800/ 450 x 525 x 550 mm 24 SF19E0022 Office Revolving Chair (High Back) 600 x 600 x 1050 /1150 mm 25 SF19E0023 Executive Revolving Chair (High Back) 650 x 650 x 1100 /1200 mm 26 SF19E0024A Steel Stool MDF Top 450 x 305 x 305 mm 27 SF19E0024B Steel Stool MDF Top 600 x 305 x 305 mm 28 SF19E0024C Steel Stool MDF Top 690 x 410 x 410 mm 29 SF19E0025 Steel Stool Cushioned Top 400 x 400 x 550 / 650 mm 30 SF19E0026 Steel Bench with Back rest 1500 x 450 x 450 / 900 mm Schedule -2 Cabinet & Book case :- 31 SF19E0027 Cabinet Plain (Full) of 0.8 mm CR Sheet 1980 x 915 x 480 mm 32 SF19E0028 Cabinet Plain (Medium) of 0.8 mm CR Sheet 1675 x 840 x 480 mm 33 SF19E0029 Cabinet Plain (Small) of 0.8 mm CR Sheet 1270 x 760 x 430 mm 34 SF19E0030 Cabinet Plain (Mini) of 0.8 mm CR Sheet 915 x 610 x 380 mm 35 SF19E0031 Cabinet with One Locker of 0.8 mm CR Sheet 1980 x 915 x 480 mm 36 SF19E0032 Cabinet with One Plain Locker of 0.8 mm CR Sheet 1675 x 840 x 480 mm 37 SF19E0033 Cabinet Wardrobe of 0.8 mm CR Sheet 1980 x 900 x 560 mm

3/81

38 SF19E0034 Cabinet Wardrobe (Mirror) of 0.8 mm CR Sheet 1980 x 900 x 560 mm 39 SF19E0035 Steel Book Case 0.8 mm CR Sheet 1675 x 840 x 380 mm Schedule -3 Lockers, Cabinets & Safe :- 40 SF19E0036 Industrial Locker Cabinet (9 Lockers) 0.8 mm CR Sheet 1800 x 900 x 400 mm 41 SF19E0037 Industrial Locker Cabinet (16 Locker) 0.8 mm CR Sheet 1800 x 1200 x 400 mm 42 SF19E0038 Glass Door Cabinet of 1 mm CR Sheet 0.8 mm CR Sheet 1980 x 900 x 480 mm 43 SF19E0039 Cash Box of 1 mm CR Sheet 1 mm CR Sheet 250 x 380 x 300 mm Schedule -4 Tin Box & Anaj Kothi:- 44 SF19E0040 Kit Box of 0.55 mm GP Sheet 680 x 380 x 300 mm 45 SF19E0041 Tin Box of 0.55 mm GP Sheet 750 x 450 x 450 mm 46 SF19E0042 Tin Box of 0.55 mm GP Sheet 750 x 600 x 450 mm 47 SF19E0043 Tin Box of 0.55 mm GP Sheet 900 x 450 x 350 mm 48 SF19E0044 Tin Box of 0.55 mm GP Sheet 900 x 600 x 450 mm 49 SF19E0045 Tin Box of 0.75 mm GP Sheet 1000 x 750 x 450 mm 50 SF19E0046 Tin Box of 0.75 mm GP Sheet 1200 x 750 x 650 mm 51 SF19E0047 Square Anaj Kothi of 0.75 mm GP Sheet 900 x 450 x 450 mm 52 SF19E0048 Square Anaj Kothi of 0.75 mm GP Sheet 750 x 380 x 380 mm Schedule -5 Racks & Cots :- 53 SF19E0049 Angle Iron Rack 900 x 900 x 380 mm 54 SF19E0050 Angle Iron Rack 900 x 900 x 450 mm 55 SF19E0051 Angle Iron Rack 1800 x 900 x 380 mm 56 SF19E0052 Angle Iron Rack 1800 x 900 x 450 mm 57 SF19E0053 Angle Iron Rack 1950 x 900 x 450 mm 58 SF19E0054 Angle Iron Rack 2100 x 900 x 450 mm 59 SF19E0055 - A Angle Iron Cot (Takhat with 25 mm Ply) 1950 x 900 x 450mm 60 SF19E0055 - B Angle Iron Cot (Takhat with 18 mm Ply) 1950 x 900 x 450mm 61 SF19E0056 Angle Iron Cot (Strip Flat) 1950 / 1870 x 900 x 450 mm 62 SF19E0057 Angle Iron Cot (18mm Plywood) 1950 / 1870 x 900 x 450 mm 63 SF19E0058 Cushion Cot Three Fold (6 Leg) 1900 / 1800 x 900 x 450 mm 64 SF19E0059 Double sleeper hostel Bed 1950/ 1870 x 900 x 450 / 1350mm Schedule -6 Computer Furniture 65 SF19E0060A COMPUTER CHAIR (MID BACK) (With Handle) 600 x 600 x 850 /950 mm 66 SF19E0060B COMPUTER CHAIR (MID BACK) (Without Handle) 600 x 600 x 850 /950 mm 67 SF19E0061A COMPUTER CHAIR (LOW BACK) (With Handle) 600 x 600 x 750 /850 mm 68 SF19E0061B COMPUTER CHAIR (LOW BACK) (Without Handle) 600 x 600 x 750 /850 mm 69 SF19E0062 COMPUTER PRINTER TABLE 900 x 600 x 750 mm 70 SF19E0063 COMPUTER CUM PRINTER TABLE 1200 x 600 x 750 mm 71 SF19E0064 COMPUTER TABLE (COMPACT) 650 x 500 x 750 mm 72 SF19E0065 PRINTER TABLE 700 x 500 x 750 mm 73 SF19E0066 PRINTER TABLE (WITH DRAWER) 800 x 500 x 750 mm 74 SF19E0067 COMPUTER TABLE (1 DRAWER & CUPBOARD) 1050 x 600 x 750 mm 75 SF19E0068 COMPUTER TABLE (3 DRAWER) 1200 x 600 x 750 mm 76 SF19E0069 COMPUTER TABLE (2 DRAWER & CUPBOARD) 1300 x 700 x 750 mm

General Requirements 1. The drawings, figures & sketches given in this catalogue are not to scale.

2. Dimensions shall be read in metric unit only & corrected dimensions from details below.

3. tolerances in dimensions are permissible as follows, if not specified :

a. In overall size + 10mm.

b. In thickness of pipe & sheets etc. as per relevant Indian Standard

4/81

4. Welding of pipe structures and MS sheets shall be done by gas welding only and on heavier

sections (Above 2.5mm) by arc welding.

5. Painting on steel sections:

a. Surface finishing shall be done before painting by weld chipping / grinding /

filing / emery paper process.

b. Two coat of metal primer of standard make like ASIAN/BERGER/SHALIMAR/

NEROLAC shall be applied after proper putty applied on the surface and over it

one under coat and the final coat of superior quality synthetic enamel paint of

standard makes like ASIAN/BERGER/SHALIMAR/NEROLAC should be

applied in T A Grey /Light Grey/ SC Grey Sheds and olive green.

c. The whole consignment of a supply order shall be painted in one shed only.

6. The color / shed of board lamination shall be approved by Consignee, if desired.

7. Wherever required Pre-laminated Medium Density Fiber Board of 18mm/25mm thick (ISI

mark)

8. If the consignee demands any special quality of laminate, etc. other than those specified the

same can be provided only after prior approval. And coasting of technical department of the

Nigam provided the cost does not materially change.

9. Minor deviations from specifications. In order to improve strength / finish & comfort of the

product or due to non-availability of particular material can be allowed at the discretion of

CSIDC.

10. Wherever specified/required, good quality chrome plating on the steel section/components

shall be provided. Two years replacement guarantee for chrome plated components/parts is

to be given by the supplier. Wherever necessary welding riveting pressing. Folding shall be

done properly.

11. Finishing & workmanship in the product is of prime importance and must be of good

quality.

12. The supplier shall ensure that the product is manufactured as per specification and all the

fitting/accessories used are of standard quality, wherever not specified. All the Table

Drawer are to be provide with reputed make sliding channel arrangement. Good quality

Bakelite handle as shown in Drawing.

13. Teak wood used in the furniture shall be seasoned wood with major defects, like dead knots

with through hole, wide cracks etc. shall not be used. Clear Poly Urethane lacquer polish

shall be done on all wooden items.

14. Wherever necessary good quality plastic / P.U milky white shoe`s are to be used.

15. Warrantee: One year from date of delivery to consignee.

5/81

If supply of sub-standard product with/without manufacturing defect is observed even after

supply. The supplier shall repair/replace the defective product free of cost, during warrantee

period within one week period.

16. (A) if any dimensional discrepancy with respect to drawing and specifications

due to calculation/printing mistake/any error is observed, the same may please be

brought to the notice of CSIDC before opening of tender.

(B) If any dimensional discrepancy is observed during manufacturing, the

same may be communicated to the In-charge Marketing immediately in writing.

(C) Wherever not mentioned. Standard manufacturing practice is to be adopted.

6/81

Schedule -1

OFFICE FURNITURE

&

SCHOOL

FURNITURE

7/81

EXECUTIVE TABLE (With Drawer three equal)

SPN NO.:- SF19E0001 OVEERALL SIZE : (L)1800 X (W) 1200 (H) 750 mm.

MATERIAL DETAILS :-

1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS-14587-1998 with upto date amendment

2. Leapping :- Teak wood half round 50mm wide, supported from inside by Jungle wood 25 x 25 mm. OR PVC leaping 25mm with proper edge banding machine.

3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1600(L)x 900(W)x725(H)mm.

with Center Support as indicated by 9, To be welded in center below the top as shown in figure item Spn No.SF19E0002

4. Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3 Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe).

5. Drawer & Cupboard:- CR sheet 0.80mm thk Confirming to IS-513 6. Cupboard Size :- size 600(D) x400(W) x450mm(H). 7. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding shelf in cup Board. 8. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer &

box. 9. Cupboard Shutter :- BOX TYPE made of 0.80mm CRCA Sheet Confirming to IS-513. 10. 2 Footrest :- ERW square pipe 32x32x1.25mm in full length and with 100mm gap

between two pipes 11. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 12. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

8/81

EXECUTIVE TABLE (With Drawer three equal) SPN NO.. :- SF19E0002

OVEERALL SIZE : (L)1800 X (W) 900 (H) 750 mm.

MATERIAL DETAILS :-

1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS-14587-1998 with upto date amendment


3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1600(L)x 750(W)x725(H)mm.

with Center Support as indicated by 9, To be welded in center below the top as shown in figure.

13. Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3 Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe).

4. Drawer & Cupboard:- CR sheet 0.80mm thk Confirming to IS-513 5. Cupboard Size :- size 600(D) x400(W) x450mm(H). 6. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding shelf in cup Board. 7. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer &



9/81

EXECUTIVE TABLE (With Drawer three equal)

SPN NO.. :- SF19E0003 OVEERALL SIZE : (L)1500 X (W) 900 (H) 750 mm.

MATERIAL DETAILS :-

1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS-14587-1998 With upto date amendment


3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1350(L)x750(W)x725(H) mm. with Center Support as indicated, To be welded in center below the top as shown in figure.

14. Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe).

4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 5. Cupboard Size :- size 600(D) x400(W) x450mm(H). 6. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding

shelf in cup Board. 7. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer &



10/81

OFFICE TABLE SPN NO.. :- SF19E0004

OVEERALL SIZE: (L) 1200 X (W) 750 (H) 750 mm.

MATERIAL DETAILS :-

1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board IS-14587-1998. with upto date amendment

2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with proper edge banding machine

3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size1100(L) x 600(W) x 725(H) mm.

4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 Size = 600(D) x 350(W) x 450mm(H).

5. Drawer Size :- 500(L)X100mm(D) Minimum. 6. Cupboard shutter :- BOX TYPE made of 0.80mm CR sheet Confirming to IS-513. 7. 2 Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length and gap between

two pipes approx. 100.mm. 8. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 9. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

11/81

OFFICE- TABEL

SPN NO.: - SF19E0005 OVERALL SIZE : (L)1200 X (W} 600 (H) 750 mm

MATERIAL DETAILS:- 1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board

IS-14587-1998. with upto date amendment 2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with

proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size1100(L) x 500(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513

Size = 500(D) x 350(W) x 450mm(H). 5. Drawer Size :- 450(L) x 100mm(D) Minimum. 6. Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length. 7. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 8. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

12/81

OFFICE TABLE

SPN NO.. :- SF19E0006 OVEERALL SIZE : (L)1000 X (W) 600 (H) 750 mm.

MATERIAL DETAILS :-

1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board

IS-14587-1998. with upto date amendment 2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with

proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size 900(L) x 450(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513

Size = 450(D) x 350(W) x 250mm(H). 5. Drawer Size :- 400(L) x 100mm(D) Minimum. 6. Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length. 7. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 8. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

13/81

STUDENT TABLE CODE No. : SF19E0007

(Overall Size : 600x450x750mm ) Steel Structure M.S. Angle Iron frame with MDF Board

MATERIAL DETAILS :-

1. Table Top :- 18mm THK. ISI Marked Pre Laminated MDF Board

IS-14587-1998. with upto date amendment.(In approved shed) Size : 600 x 450 mm

2. Edge Leaping :- Teak wood half round 18mm wide polish, OR PVC leaping 18mm With proper edge banding machine

3. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 550 (L) x 400(W) x 732(H) mm. 4. Foot Rest :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

450 600

18 mm

750

550 400

125

32 x 32 x 2.5 mm

14/81

STUDENT CHAIR CODE No. : SF19E0008

(Steel Structure M.S. Angle Iron frame with MDF Board) 900 x 400 / 375 x 480

MATERIAL DETAILS :-

1. Chair Seat :- 18mm THK. ISI Marked Pre Laminated MDF Board

IS-14587-1998. with upto date amendment.(In approved shed) Size: 400 x 400mm

2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine.

3. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 375 (L) x 375 (W) x 462 (H)mm. and total height with back rest 900 mm. with all

Supports as shown in figure. 4. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 5. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

400 120

400

480

900

375 375

32 x 32 x 2.5 mm

15/81

ALL STEEL STUDENT DESK Spn No.. :- SF19E0009

OVERALL SIZE : 900 x 425 x 750mm.

MATERIAL DETAILS :-

SF19E0009 (A) Without Shelf SF19E0009 (B) With Shelf

1. Desk table Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall

be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm.

2. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 900 (L) x 425 (W) x 750(H) mm. 3. Shelf Size :- Made from 0.80 mm CR sheet formed covering frame of M.S Angle 32 x

32 x 2.5 mm in size 900 (L) x 425 (W), 175mm below the top. 4. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

Sheet to be folded 3times, 1st bend over the angle 32 mm, 2nd bend 15 mm inside over the Angle edge, 3rd bend 10mm to avoid sharp edge of sheet.

750

125

900

425

16/81

ALL STEEL BENCH FOR STUDENTS Spn No.. :- SF19E0010

OVERALL SIZE : 900 x 300 x 450mm.

MATERIAL DETAILS :-

1. Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall

be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm.

2. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 900 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 3. Foot Rest support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 4. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 5. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc

Sheet to be folded 3times, 1st bend over the angle 32 mm, 2nd bend 15 mm inside over the Angle edge, 3rd bend 10mm to avoid sharp edge of sheet.

300 300

450

17/81

ALL STEEL DUAL DESK( Three Seater)

Spn No. : - SF19E0011 OVERALL SIZE : (L)1500 x (W) 900 X (H) 750/450mm.

MATERIAL DETAILS :- 7. Desk & Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall

be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. Overall Frame Size : 1500 x 900 x 750 Desk height x 475 Bench height.

8. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1500 (L) x 375 (W) x 750 (H) mm, with two equal distance width wise angle support.

9. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1500 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 10. Shelf Size :- Made from 1.00 mm CR sheet formed covering frame of M.S Angle 32 x

32 x 2.5 mm in size 1500 (L) x 375 (W), 175mm below the top. 11. Foot Rest support :- M.S Angle 32 x 32 x 2.5 mm in full length, 150mm above ground. 12. Special Requirement : - Machine made corner plates corner plates should be folded towards

inside to avoid the sharp edge, No sharp edge on any part of dual desk shall be allowed.

13. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc

18/81

ALL STEEL DUAL DESK( Three Seater Junior)

Spn No. : - SF19E0012 OVERALL SIZE: (L)1150 x (W) 900 X (H) 750/475mm.

(Without back rest & without shelf)

MATERIAL DETAILS :-

1. Desk & Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall

be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. Overall Frame Size : 1150 x 900 x 750 Desk height x 475 Bench height

2. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1150 (L) x 375 (W) x 750 (H) mm, with two equal distance width wise angle support.

3. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1150 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 4. Shelf Size :- Made from 1.00 mm CR sheet formed covering frame of M.S Angle 32 x

32 x 2.5 mm in size 1150 (L) x 375 (W), 175mm below the top. 5. Foot Rest support :- M.S Angle 32 x 32 x 2.5 mm in full length, 150mm above ground. 6. Special Requirement :- Machine made corner plates corner plates should be folded towards

inside to avoid the sharp edge, No sharp edge on any part of dual desk shall be allowed.

7. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc

19/81

DUAL DESK (Two seater Junior) Spn No. : SF19E0013

(With Angle iron frame) 900x850x/900/450/750mm

MATERIAL DETAILS :-

1. Desk & Bench Top :- 18mm thk ISI Marked Pre Laminated MDF Board confirming to

IS 14587:1998, Overall Frame Size : 900 x 850 x 750 Desk height x 450 Bench height & 900mm Backrest height.

2. Desk Top :- made of 18mm thk MDF Board size: 900 x 450mm. 3. Bench Top :- made of 18mm thk MDF Board size: 900 x 325mm. 4. Back rest ;- made of 18mm thk MDF Board size: 900 x 150mm 5. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping

18mm with proper edge banding machine 6. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 425 (W) x

732 (H) mm, with two equal distance width wise angle support. 7. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 300 (W) x 432 (H) mm, with two equal distance width wise angle support. 8. Shelf Size :- Made from 18mm thk MDF Board in frame of M.S Angle 32 x

32 x 2.5 mm in size 850 (L) x 425 (W), 175mm below the top. 9. Special Requirement :- No sharp edge on any part of dual desk shall be allowed. 10. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc

Back Support

20/81

DUAL DESK (Two Seater Senior) Spn No. : SF19E0014

(With angle iron frame) 1050x900x900/450/750mm

MATERIAL DETAILS :- 1. Desk & Bench Top :- 18mm thk ISI Marked Pre Laminated MDF Board confirming to

IS 14587:1998, Overall Frame Size : 1000 x 900 x 750 Desk height x 450 Bench height & 900mm Backrest height.

2. Desk Top :- made of 18mm thk MDF Board size: 1050 x 450mm. 3. Bench Top :- made of 18mm thk MDF Board size: 1050 x 325mm. 4. Back rest ;- made of 18mm thk MDF Board size: 1050 x 150mm 5. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping

18mm with proper edge banding machine 6. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1000 (L) x 425 (W) x

732 (H) mm, with two equal distance width wise angle support. 7. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1000 (L) x 300 (W) x 432 (H) mm, with two equal distance width wise angle support. 8. Shelf Size :- Made from 18mm thk MDF Board in frame of M.S Angle 32 x

32 x 2.5 mm in size 1000 (L) x 425 (W), 175mm below the top. 9. Special Requirement :- No sharp edge on any part of dual desk shall be allowed. 10. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc

21/81

STUDENT DESK (Angle iron frame) Spn No.. : SF19E0015

(overall size - 900x425x750 mm MDF Top)

MATERIAL DETAILS :-

SF19E0015 (A) Without Shelf SF19E0015 (B) With Shelf

1. Desk table Top :- Made from 18mm thk ISI Marked Pre Laminated MDF Board confirming

to IS 14587:1998 with TOP size: 900 x 425 mm. 2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping

18mm with proper edge banding machine. 3. Frame Structure :- As shown in figure made of Mild steel Angle 32 x 32 x 2.5 mm

in size 850 (L) x 375 (W) x 732(H) mm. with support & footrest. 4. Shelf Size :- Made from 18mm thk ISI Marked Pre Laminated MDF Board in M.S

Angle 32 x 32 x 2.5 mm in size 850 (L) x 375 (W), 175mm below the top.

5. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 6. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 7. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

32 x 32 x 2.5 mm

22/81

STUDENT BENCH

(Angle iron frame) Spn No.: SF19E0016

(Overall Size : 900x300x450mm MDF Top)

MATERIAL DETAILS :-

1. Bench Top :- Made from 18mm thk ISI Marked Pre Laminated MDF Board confirming

to IS 14587:1998 with TOP size: 900 x 300 mm. 2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping

18mm with proper edge banding machine. 3. Frame Structure :- As shown in figure made of Mild steel Angle 32 x 32 x 2.5 mm

in size 850 (L) x 250 (W) x 432(H) mm. with support & footrest. 4. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

300

450

250

850

900

125

23/81

OFFICE CHAIR (Fixed back) SPN NO. :-- SF19E0018

OVERALL SIZE : (H) 950/450* (W) 550*(D) 550mm.

METERIAL DETAIL:-

1. Frame :- Mild steel Elliptical (Capsule) pipe 32mm Major Dia x 2mm Thick, frame as shown in figure. (distance between legs 550mm at ground)

2. Seat :- 450 (W) x 450 (D) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. Seat height 450mm from ground.

3. Back rest :- 450 (W) x 500 (H) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high

quality leatheriest rexin based cloth or other suitable high quality cloth. 4. Fitting :- Seat shall be fitted over the frame as shown in figure with minimum 3

width wise flat 32 x 5mm at equal distance below the seat with nut bolt (2 flat shown in figure but in chair 3 flats to be used), and back rest seat with suitable good quality fixed arrangement as shown in figure.

5. Handle :- Syncro soft handles with bracket as shown in last figure. 6. Shoes :- P.U / Rubber shoe`s are to be used (4 No’s) compulsorily in legs as

shown in figure. 7. Painting :- Complete chair frame to be powder coated after 7 tank anti corrosion

Treatment. 8. Also refer “General Requirements for Welding / Finishing / Packing & etc.

24/81

OFFICE CHAIR (Flexible Back) SPN NO. :-- SF19E0019

OVERALL SIZE : (H) 950/450* (W) 550*(D) 550mm.

METERIAL DETAIL:-

1. Frame :- Mild steel Elliptical (Capsule) pipe 32mm Major Dia x 2mm Thick, frame as shown in figure. (distance between legs 550mm at ground)

2. Seat :- 450 (W) x 450 (D) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. Seat height 450mm from ground.

3. Back rest :- 450 (W) x 400 (H) mm half round from top Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth.

4. Fitting :- Seat shall be fitted over the frame as shown in figure with minimum 3 width wise flat 32 x 5mm at equal distance below the seat with nut bolt (2 flat shown in figure but in chair 3 flats to be used), and back rest seat with suitable good quality flexible spring as shown in figure.

5. Handle :- Syncro soft handles with bracket as shown in last figure. 6. Shoes :- P.U / Rubber shoe`s are to be used (4 No’s) compulsorily in legs as

shown in figure. 7. Painting :- Complete chair frame to be powder coated after 7 tank anti corrosion

Treatment. 8. Also refer “General Requirements for Welding / Finishing / Packing & etc..

25/81

OFFICE REVOLVING CHAIR (High Back) Spn No.: - SF19E0022

W600 x D600 x H1050 / 1150 mm METERIAL DETAIL:-

1. Overall size: Width 600mm Without castors Depth 600mm Height 1050 to 1150mm Adjustability of seat height 450 to 550mm

2. Seat size: 500x500mm approx. 3. Back size: 500x610 (H) approx. 4. Material:- Seat and back should be made up of 12mm thick hot pressed plywood

upholstered with fabric and molded Polyurethane foam (high density 40 mm thick), together with molded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort.

5. Handle: The armrest should be one piece “Syncro soft handles” with bracket as shown in figure and scratch and wear resistant.

6. Castors wheels: The twin wheel castors should be high quality injected molded. 7. Pedestal Assembly: The pedestal should chrome plated steel base casted pedestal, with

proper lift mechanism. 8. Upholstery: The seats and backs are to be covered with superior quality latheriest rexin

cloth. 9. Finish: All steel components are to be painted after proper anti corrosion pretreatment of

surface. 10. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

26/81

Steel Bench with Back Rest (With MDF Seat & Back)

CODE NO. SF19E0026 Size: L-1500xW-450xH-450/900mm

Material Detail:- 1. Frame : ERW Squire pipe 25x25x1.25 four side welded. 2. Seat & Back : 18 mm thick ISI Mark MDF Board with 18mm wide teak wood lapping seat size

(L)1500x(D)450mm,Back size (L) 1500x(H) 200 mm 3. Arms : Teak wood arms of size (W) 50*(THK)25*(L)

400 mm and front curved , under side grooved profile matching with pipe. Painted with Black enamel paint.

4. Fitting : Seat shall be fitted with minimum 22 nos. round head steel screws. The backrest shall be fitted on two longitudinal pipe with gap of 75mm.and 12 nos. minimum steel round head screws. In wooden handle 3 nos. Round head steel screws on each side shall be used.

5. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

27/81

Schedule-2

CABINETS

&

BOOKS

CASES

28/81

CABINET PLAIN SPN NO.:- SF19E0027

OVERALL SIZE : (H) 1980 x (W) 915 x (D) 480mm.

1. Body 2. Self 3. Legs 4. Door stiffener 5. Leaver Road 6. Door Handle MATERIAL DETAILS:-

1. The overall design and appearance of cabinet shall be as per figure. 1. 0.8 mm CR Sheet shall be used of prime quality, Confirming to IS-513. 2. Each shelf be formed such the edges are bend two times at right angle, first bend 30mm

and second bend 8mm. 3. Door stiffener frame inside to its full height in top hat section size 100mm width. 4. Lever rod shall be of Ms 12mm round/square bar , or 10mm bright bar. 5. Size of hinges shall be 75mm length x 1.6mm thk. 6. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 7. Machine made lever plate (patla)with brass bush of good quality or machine made six lever

type patla. Patla shall be covered by box covered by box over fitted with round head screws.

8. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of size(h) 65 x (W) 50mm fitted on four screws or “ GRACE” LOCK. Keys in duplicate with key rings shall provided.

9. Metallic key cover electroplated nickel/chrome on front side of the door shall be provided. 10. For door, die cast chrome plated handle fitted with washer and double nut. 11. Leg height shall be 125 mm x 100 mm . 12. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

29/81

CABINET PLAIN SPN NO.:- SF19E0028

OVERALL SIZE (H) 1675 x (W) 840 x (D) 480mm.

1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5) Legs 6) Body MATERIAL DETAILS:-

1. The overall design and appearance of cabinet shall be as per figure. 2. 0.8 mm CR sheet shall be used of prime quality, Confirming to IS-513. 3. Each shelf shall be formed such the edges are bend two times at right angle, first bend

30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar , or 10mm bright bar.\ 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR. sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six

lever type. Patla. Patla shall be covered by box covered by box over fitted with round head screws.

9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of size(H) 65 x (W) 50mm fitted on four screws or “ GRACE” lock. Keys in duplicate with key rings shall provided.

10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm . 13. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

30/81

CABINET PLAIN MINI

SPN NO.:- SF19E0030 OVERALL SIZE : (H) 915 x (W) 610 x (D)380 mm.

1) Door stiffener 2)Lever Rod & Plate 3)Door Handle 4)Shelf 5) Legs 6) Body MATERIAL DETAILS:-

1. The overall design and appearance of cabinet shall be as per figure. 2. 0.8 mm CR sheet shall be used of prime quality, Confirming to IS-513. 3. Each shelf shall be formed such the edges are bend two times at right angle, first bend

30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar , or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six

lever type. Patla. Patla shall be covered by box covered by box over fitted with round head screws.

9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zine alloy body of size(H) 65 x (W) 50mm fitted on four screws or “ GRACE” lock. Keys in duplicate with key rings shall provided.

10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm . 13. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

31/81

CABINET PLAIN WITH ONE LOCKER SPN NO.:- SF19E0031

OVERALL SIZE: (H) 1980 x (W) 915 x (D) 480mm.

1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5)locker. MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure. 2. 0.8 mm CR sheet shall be used of prime quality, Confirming to IS-513. 3. Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and

second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar , or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type

Patla. Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of

size (H) 65 x (W) 50mm fitted on four screws or “ GRACE” lock. Keys in duplicate with key rings shall provided.

10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm. 13. Locker size (W) 420 x (H) 254 shall be provided, Each licker shall be provided with box type door

with die cst chrome plated handle. Lock shall be plate type with 150mm sliding plate arrangement or 2 nos. 25mm pin rod/ 2nos. 30mm wide plate sliding arrangement.


CABINET PLAIN WITH ONE LOCKER

32/81

SPN NO.:- SF19E0032 OVERALL SIZE: (H) 1675 x (W) 840 x (D) 480mm.

1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5)locker. MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure. 2. 0.8 mm CR sheet shall be used of prime quality, Confirming to IS-513. 3. Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and

second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar , or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type. Patla.

Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zine alloy body of

size(H) 65 x (W) 50mm fitted on four screws or “ GRACE” lock. Keys in duplicate with key rings shall provided.

10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm . 13. Locker size (W) 420 x (H) 254 shall be provided, Each licker shall be provided with box

type door with die cst chrome plated handle. Lock shall be plate type with 150mm sliding plate arrangement or 2 nos. 25mm pin rod/ 2 nos. 30mm wide plate sliding arrangement.


33/81

CABINET WARDROBE

Spn No.: SF19E0033 OVERALL SIZE: (H) 1980 x (W) 900 x (D) 560mm.

NOTE :- Detail are given in the Annexure 1.Door Stiffener 2. Door Handle 3.Locker 4. Shelf 5. Body

The overall design and appearance of cabinets shall be as per their respective figure. The 0.8 mm CR sheet used shall be of prime quality Confirming to IS-513, each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. Size of hinges shall be 75mm length x 1.6mm thk. Brackets shall be made of 1.6mm of MS. sheet, riveted of bolted on each side of hinges. Machine made lever plate (patla ) withy brass bush of good quality or machine made six lever type Patla . Patla shall be covered by box covered by box over fitted with round head screws. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. For door, die cast chrome plated handle ritted with washer and double nut. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

For Spn No. SF19E0034

Top shelf of cabinet shall be fitted at 914 mm from top. This portion called wardrobe shall be

provide with partition in full length. On left side of wardrobe one locker with 250mm height. Locker shall be provided with box type door with die cast chrome plated handle. Lock shall be plate type with 150mm slidding plate/25 mm pin rod/ 30mm plate sliding arrangement.

On the right side of wardrobe one hanger pipe of 18x1.2mm thick chrome plated shall be provided.

One mirror ( 1200x300mm) of good quality ATUL/modi make, fitted on left door from outside in pressed steel section.

Leg height shall be 125x100 mm. Please refer “General requirements.” Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

34/81

COMPONENT DETAILS S.No. Spn No.. Type Size mm Sheet No. of Hinges Shelf No.

(HxWxD) & Brackets & Depth

01. SF19E0028 CABINET PLAIN 1980x915x480 0.8mm 6 4 nos.x/400mm 02. SF19E0029 CABINET PLAIN 1675x840x480 0.8mm 6 4 nos.x/400mm 03. SF19E0030 CABINET PLAIN 1270x760x430 0.8mm 4 3 nos.x/355mm 04. SF19E0031 CABINET PLAIN 915x610x380 0.8mm 2 2 nos.x/330mm 05. SF19E0032 CABINET PLAIN 1980x915x480 0.8mm 6 4 nos.x/400mm WITH ONE LOCKER 06 SF19E0033 CABINET PLAIN WITH 1675x840x480 0.8mm 6 4 nos.x/400mm ONE LOCKER 07 SF19E0034 WARDROBE 1980X900X560 0.8mm 6 3 nos.x/500mm 08 Please Refer “General Requirements.”

35/81

STEEL BOOK CASE Spn No.:- SF19E0035

OVERALL SIZE : (H) 1675x(W) 840x (D) 380mm.

MATERIAL DETAILS :- 1. The Design of this steel Bookcase shall be as shown above. 2. Sheet CR prime 0.80 mm thick Confirming to IS-513 with latest Amendment 3. Compartment- 4, equal in size. 4. Six leaver locks of high quality in each shutter operated by one key, supplied with key ring. 5. Chrome plated, metallic handles 2 No’s on each shutter from outside. 6. Plane glass, 4mm thick in each shutter fitted in suitable frame from inside & P.U/rubber packing

should be provided around the glass fitting. 7. Shutter sliding on ball bearing, 2 No’s in each door with suitable system / double roller system. 8. One additional plate of 127mm height x 830mm width shall be provided on lower side. 9. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

36/81

Schedule -3

LOCKERS,

CABINETS

&

SAFE

37/81

INDUSTRIAL LOKCER CABINET (9 Lockers)

SPN NO.:- SF19E0036 OVERALL SIZE: (H)1800 x (W) 900 x (D) 400mm.

1. Body 0.8 mm CR SHEET Confirming to IS-513 2. Handle Nickel/ Chrome plated. 3. Key hole, 4. Door stiffener. 5. Label Holder 6. Leg. METERIAL DETAILS:-

1. The design of this industrial locker cabinet having 9 locker shall be as shown above. 2. Six of locker doors shall be 260x550mm height. 3. Separate locking system in each locker. Locks of 6 lever of good quality with duplicate keys

& Key rings. In addition manual locking lache to be provided for external lock. 4. Label Holder Nickel/chrome plated or Aluminum on each door. 5. Two hinges 50x1.0mm thick in each door, along with two brackets of 1.25mm thick. 6. Door stiffener in side to its full height in top hat section of suitable size. 7. Please refer “ General Requirements “. 8. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

400

100

38/81

CASH BOX

SPN NO.: - SF19E0039 OVERALL SIZE: (H) 250 X (W) 380 X (D) 300mm.

MATERIAL DETAILS :-

1. The overall design & appearance of this cash box shall be as shown above, 2. Cash box body CR sheet, 1mm thick. 3. Upper edge bending 20mm as shown in figure and second edge bending 8mm approx. 4. A removable tray of 1mm thick CR sheet Confirming to IS-513 with four partitions. Width

& depth shall be 200 mm rest of the width shall be kept open for keeping currency notes in bottom compartment.

5. Door closing shall be made with machine made patla provided with quality 6-lever lock in the lid as per arrangement provided in the steel cabinets, with Nickel/Chrome plated key cover.

6. Strong chrome plated/Nickel plated/handle on door sheet 1.60mm thick for door. 7. Key cover of best quality Nickel or chrome Plated. 8. Hinges : 2Nos., size 50x1.25mm thick. 9. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

39/81

Schedule -4

TIN BOX

&

ANAJ

KOTHI

40/81

TIN BOX Spn No.:- SF19E0043

OVERALL SIZE : (L) 900 (W) 450 (H) 350 mm.

1. The over all desigh & appearance of this tin box shall be as shown in Spn No. SF19E0041, except the dimensions which in this case (L) 900 x (W) 450 x (H) 350 mm.

2. Other constructional details shall be similar to that as tin box Spn No. SF19E0041

Schedule -5

RACKS,

&

COTS

41/81

ANGLE IRON RACK

Spn No. :- SF19E0049 OVERALL SIZE: (H) ) 900X (W) ) 900X (D) 380mm.

1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note: Details are given in the Annexure

42/81

ANGLE IRON RACK

Spn No. :- SF19E0050 OVERALL SIZE: (H) ) 900 (W) ) 900 (D) 450mm.


43/81

ANGLE IRON RACK

Spn No. :- SF19E0051 OVERALL SIZE : (H) 1800 (W) ) 900 (D) 380mm.


44/81

ANGLE IRON RACK

Spn No. :- SF19E0052 OVERALL SIZE : (H) 1800 (W) 900 (D) 450mm.

1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are given in the Annexure

45/81

ANGLE IRON RACK


1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are in the Annexure

46/81

ANGLE IRON RACK


1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are given in the Annexure

47/81

Angle Iron Rack Annexure

1. The over all design & appearance of this Angle iron rack shall be as shown in item wise figure. 2. Angle iron 32x32x2.5.00 mm thick (Non slotted) M.S angle shall be used, holes for 8 mm dia bolt

to be drilled at location of shelf fitting (No extra holes to be provided), joints in angle iron Leg shall not be allowed it should be solid single peace.

3. Each shelf shall be made from 0.8 mm thick CR sheet. Shelf shall be formed such that lengthwise edges are bent two times at right angles. First bend shall be 25 mm & second bend 8mm. Widthwise edges are to be bent only one time.

4. Press cut shelf corner plate’s 8nos. in upper shelf and 8no. in lower shelf of 0.80 mm thick CR sheet shall be used in all racks, Racks having 5 shelf or more additional 8 corner plates at center shelf to be provided. (Refer “Corner plate Location” in below shown table)

5. Galvanized nut both of hexagonal hand 8mm dia x 10mm long. 6. No sharp edges on angle iron ends shall be allowed, four plastic shoes of appropriate size shall be

provided for legs. 7. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

Sr. No. Specification No. Size (mm) No. Shelf Corner plate Location shelf wise from top

1 SF19E0049 900H x 900W x 380D 3 1ST & 3rd 2 SF19E0050 900H x 900W x 450D 3 1ST & 3rd 3 SF19E0051 1800H x 900W x 380D 5 1ST & 3rd & 5TH 4 SF19E0052 1800H x 900W x 450D 5 1ST & 3rd & 5TH 5 SF19E0053 1950H x 900W x 450D 6 1ST & 3rd & 6TH 6 SF19E0054 2100H x 900W x 450D 7 1ST & 4TH & 7TH

48/81

ANGLE IRON COT (TAKHAT) WITH PLY

Spn No. : - SF19E0055A, SF19E0055B OVERALL SIZE A : (L) 1950 x (W) 900 X (H) 450mm with 25mm ISI Marked Plywood

B : (L) 1950 x (W) 900 X (H) 450mm with 18mm ISI Marked Plywood

SPECIFICATION – SF19E0055 A:-

1. Design & appearance of the cot shall be as per shown in the fig. 2. Angle iron frame, 32 x 32 x 3 mm thick . 3. Widthwise Angle iron support, 3 No’s 25x25x 2.5mm, shall be at equal distance. 4. Head bow and foot bow Angle Iron Frame 35x35x5 5. Provided with arrangement for Mosquito Net Poles (Poles are not to be supplied) 15mm dia

x x1mm thick x 75 mm length 6. Angle Iron frame sixe L 1950 x W 900 mm 7. Height of angle iron frame from ground level -450mm. 8. Total length including head/foot Leg bow – 1980mm. 9. ISI Marked Plywood, (L 1944 x W 894 x 25 mm) Phenol Bonded BWP Grade as per IS 710:2010 10. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

SPECIFICATION – SF19E0055 B :-

1- ISI Marked Plywood, (L 1944 x W 894 x 18 mm) Phenol Bonded BWP Grade as per IS 710:2010 2- other details shall be as per Specification no. SF19E0055 A

1950

900

49/81

ANGLE IRON COT (strip flats)

Spn No. : - SF19E0056 OVERALL SIZE : (L) 1950/1870 (W) 900 (H) 450mm.

SPECIFICIATION : - 1. Design and appearance as shown in fig. 2. Angle iron frame 32 x 32 x 3mm. 3. 2 Lengthwise angle iron support at equal distance made of M.S Angle 25 x 25 x 3 mm 4. 13nos strips widthwise made out of 1.0mm. thick CR sheet having width 100mm formed type

first bend 12mm second bend 8mm. 5. Head bow and foot bow pipe: ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 6. Head bow /foot bow pipe support in widthwise one in each side size ERW square pipe 40 x 40 x

1.5 mm thick (weight=1.7 kg/m). 7. Head bow height = 650mm & support at 350mm from top, 8. Leg Bow height = 600mm & support at 300mm from top. 9. Head bow /foot bow vertical pipe support ERW square pipe 40 x 40 x 1.5 mm thick, 2 No’s on

each side at equal distance. 10. Folding arrangement of head bow/foot bow by flat iron 18x4mm duly riveted. 11. Mosquito net poles support of 12mm i.d. pipe 1mm thick. 75 long duly plugged from bottom. 12. Plastic / rubber shoe on legs. 13. Height of angle iron main frame from ground level –450mm. 14. Total length of bed including head bow/foot bow –1950mm. 15. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

1950

450

650 350

600 300

900 900

900

50/81

ANGLE IRON COT (Plywood)

Spn No. : - SF19E0057 OVERALL SIZE : (L) 1950/1870 (W) 900 (H) 450mm.

SPECIFICIATION : - 1. Design and appearance as shown in fig. 2. Angle iron frame 32 x 32 x 3mm. 3. 2 widthwise angle iron support at equal distance made of M.S Angle 25 x 25 x 3 mm 4. ISI Marked Plywood, (L 1864 x W 894 x 18 mm) Phenol Bonded BWP Grade as per IS 710:2010. 5. Head bow and foot bow pipe: ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 6. Head bow /foot bow pipe support in widthwise one in each side size ERW square pipe 40 x 40

x 1.5 mm thick (weight=1.7 kg/m). 7. Head bow height = 650mm & support at 350mm from top, Leg Bow height = 600mm &

support at 300mm from top. 8. Head bow /foot bow vertical pipe support ERW square pipe 40 x 40 x 1.5 mm thick, 2 No’s

on each side at equal distance. 9. Folding arrangement of head bow/foot bow by flat iron 18x4mm duly riveted. 10. Mosquito net poles support of 12mm i.d. pipe 1mm thick. 75 long duly plugged from bottom. 11. Plastic / rubber shoe on legs. 12. Height of angle iron main frame from ground level –450mm. 13. Total length of bed including head bow/foot bow –1950mm. 14. Also refer “General Requirements for Welding / Painting / Finishing / Packing & etc.

1950

450

900

350650 600

300

900 900

51/81

Schedule -6

COMPUTER

FURNITURE

52/81

General Requirements for Schedule -6 (Computer Furniture)

For Suppliers 1. The sizes written in the specifications are cut size while finished sizes

are given in the details drawing. 2. Tolerance in the finished products wherever not specified shall be as

follows :- a. Wooden Section width + 5.0 mm and Thickness + 3.00 mm. b. Overall dimensions + 10 mm. c. Pipe thickness - As per IS. 3. Finishing & Workmanship in the furniture is of prime importance and

must be of high standard. 4. Before polishing, the surface should be finished with sand paper and

properly grain filled. 5. Polishing shall be done properly, preferably Touch Wood Polish. 6. Teak wood used in furniture shall be naturally seasoned without any

defects like dead knot, cracks, dry root, upset grains, twisted fibre etc. On face side and edges of the furniture, sap wood shall not be used.

7. Before delivery to the consignee, the unit shall ensure that the product is as per specification and all the accessories are provided with the product.

8. The design and drawings of the furniture are not to the scale. For Consignees 1. Please do not accept damaged / broken furniture. 2. Before accepting the delivery of furniture, please ensure that the

finishing and polishing / painting of the furniture is not affected during transportation.

3. Please do ensure, before accepting delivery, the each furniture item Inspected by Inspecting Authority and Supplier’s Metal / Paper Stickers having following details :-

- Suppliers Name / Address. - Supply Order No. / Date. - Date of Supply. 4. Please do not accept any furniture without Inspection Certificate and

Seal of Inspecting Authority / Suppliers Sticker, in order to ensure quality of furniture, as per specification.

53/81

COMPUTER CHAIR MID BACK

Spn No.. : - SF19E0060A, SF19E0060B Overall Size: 600 x 600 x 850 / 950 mm

SPECIFICATIONS:

SF19E0060 (A) With Arm Rest / Handle SF19E0060 (B) Without Arm Rest / Handle

1. Overall size : Width 600mm Depth 600mm Height 850 to 950mm Adjustability of seat height 400 to 500mm 2. Seat size: 450 x 450mm approx. 3. Back size: 430 x 500 (H) approx. 4. Material: Seat and back should be made up of 12mm thick hot pressed plywood upholstered

with fabric and molded Polyurethane foam (high density 40 mm thick), together with molded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort.

5. Arm Rest: The armrest should be one piece “Syncro soft handles” with bracket as shown in another figure and should be scratch and wear resistant.


proper lift mechanism. 8. Upholstery: The seats and backs are to be covered with good quality matty / tapestry cloth. 9. Finish: All steel components are to be painted after proper anti corrosion pretreatment of


54/81

COMPUTER CHAIR WITH HANDLES

(Low Back) CODE NO. SF19E0061A & SF19E0061B

Overall Size: 600 x 600 x 750 / 850 mm

SPECIFICATIONS:

SF19E0061 (A) With Arm Rest / Handle SF19E0061 (B) Without Arm Rest / Handle

1. Chair shall be as shown in the figure. 2. Seat: size shall be 430 x 430 mm on 10 mm thick moulded comm. ply with 40 mm thick high

density foam covered with tapestry. 3. Back rest: size shall be 430 x 350 mm on 10 mm thick moulded comm. ply with 40 mm thick

high density foam covered with tapestry. The height of back rest shall be 900 & 500 mm for top and bottom edges respectively. The back rest shall be provided with lifting arrangement on flat iron & helical spring.

4. Arm Rest: The armrest should be one piece “Syncro soft handles” with bracket as shown in another figure and should be scratch and wear resistant.


proper lift mechanism. A Central spindle of 25 mm dia rod without threads shall be provided with revolving arrangement. The adjustable height of chair shall be from 450 to 550 mm.

7. Upholstery: The seats and backs are to be covered with good quality matty / tapestry cloth. 8. Finish: All steel components are to be painted after proper anti corrosion pretreatment of


55/81

COMPUTER TABLE (COMPACT)

CODE NO. SF19E0064 Size: 650 x w 500 x H 750 mm

SPECIFICATIONS: 1. As shown in Figure, Top-size (L) 650 x (W) 500 mm made of 18 mm thick ISI marked pre

laminated MDF board. The top shall be firmly screwed on 25 x 25 x 1.25 mm square pipe frame as shown in drawing.

2. Sliding key board tray shall be made of 18 mm pre laminated MDF board of size 564 mm (L) x 400 mm (W). The gap between top and tray shall be 110 mm.

3. Key board tray shall smoothly roll over telescopic sliding channel of minimum 1.60 mm thick duly powder coated and fixed to the side panels as shown in drawing.

4. One storage shelve for keeping CVT and other appliance shall be made of 18 mm MDF board of size 630 mm (L) x 360 mm (W). The height of the shelve shall be 100 mm from upper face of the base (Bottom) pipe.

5. One sliding mouse tray shall be provided below the key board tray as shown in drawing. 6. One bracket made of 20 x 20 x 1 mm square pipe and 10 mm bright bar rod as shown in

drawing shall be fixed on right hand side of the table to support CPU.

650 500

750

125

564

250

600

56/81

7. The edges of the pre laminated MDF board wherever used shall be sealed with beading of 18mm half round teak wood with polish to be used, OR PVC leaping tape 3mm thick, 18mm wide to be used with proper edge banding machine.

8. Steel structure shall be made of 2 rectangular base pipes of size 50 x 25 x 1.5 mm about 500 mm length placed along the width, 4 vertical pipes of size 25 x 25 x 1.25 mm square pipe shall be weld on the top of the vertical pipes to support the top. 4 horizontal support of square pipes 25 x 25 x 1.25mm shall also be weld to the vertical pipe as shown in drawing. 2 rectangular pipe of size 50 x 25 x 1.25 mm shall also be weld to the vertical pipes at the upper end widthwise.

9. The open ends of the base pipe shall be plugged with suitable rubber plugs. 4 adjustable shoes are also to be provided below the base pipe. The overall height of the table shall be inclusive of adjustable shoes.


Recommended by Technical Specification Committee Dated 23-11-2016

technical particular of furniture part i furniture part-i specification.pdf · technical particular...

Documents