technical lighting control water wizard · 3025 de baene, montreal, quebec, canada, h4s 1k8...
TRANSCRIPT
WATER WIZARDTechnical Lighting Control
WATERPROOFHOUSING FOR
® Pocket Wizard Plus III
USE
R M
AN
UA
L
3025 De Baene, Montreal, Quebec, Canada, H4S 1K8 [email protected] www.aquatica.ca
Tel.: 514-737-9481
Foreword Technical Lighting Control would like to thank you for acquiring the Water Wizard housing for your Pocket Wizard Plus III transceiver. Technical Lighting Control is part of a group, along with Aquatica and Amphibico, of affiliated companies that dedicates themselves in the underwater imaging enthusiast the best instrument for their passion. The products are developed by and for demanding professional in this field. With regular maintenance, your Water Wizard housing will gives you years of faithful service, before using it, we recommend that you make yourself familiar with the Pocket Wizard® Plus III transceiver and take a moment to read this owner manual. Instruction: First unscrew the four hexagonal screws that close’s the front cover, remove this cover and place somewhere clean and safe. Plug in the mini phone jack into the transceiver; position it so that the dowel pin fits properly in the mounting hole in the back of the transceiver. Inspect and clean and lubricate the O-ring and close back the cover, tighten down the screws, making sure not to over torque them. Remove the bulkhead cap, inspect for cleanliness, lubricate the sync cord and/or extension cord O-ring and install in the Water Wizard bulkhead connector, connect the end of the sync cord to the camera housing or the underwater strobe(s). Most common sync cords used are: Ikelite to Nikonos single sync cord # 4104.31: For connecting the Water Wizard housing to most housing equipped with a Nikonos type of strobe connector Ikelite to Ikelite single cord # 4103.51: For connecting the Water Wizard housing to one Ikelite strobe or to any housing equipped with an Ikelite bulkhead. Ikelite to Ikelite double cord # 4103.52: For connecting the Water Wizard housing to two Ikelite strobes. Ikelite to Sea & Sea single cord # 4118.1: For connecting the Water Wizard housing to one Sea & Sea or Inon strobe. Ikelite to Sea & Sea double cord # 4118.2: For connecting the Water Wizard housing to two Sea & Sea or Inon strobes.
Additional extensions are also available:
Ikelite 4.5m/15ft extension cord # 4102.15 Ikelite 0.9/3ft extension cord # 4102.03
Check www.ikelite.com for additional sync cords combination.
1
2
3
3
3
3
5
7
7
6 4
1) ON/OFF BUTTON2) TEST / TRIGGER BUTTON3) CLOSING FASTENER (4x)4) HEXAGONAL KEY5) CONNECTING BULKHEAD6) BULKHEAD CAP7) 1/4-20" THREADED MOUNTING HOLE
WATER WIZARD
41
04
.31
4102.15
WATER WIZARD
CANADAMade in
PLUS III
MODE
TEST
A B
C D
CH 17
4102.15
WATER WIZARD
CANADAMade in
WATER WIZARD
CANADAMade in
41
03
.51
4103.5
2
4102.15
SCHEMATIC USINGSTROBES, SYNC CORD AND EXTENSION FROM
®IKELITE
Pocket Wizard PLUS IIIto Studio flash unit
®
Pocket Wizard PLUS IIIin Water Wizard housing
®to two Ikelite strobes
®
Pocket Wizard PLUS IIIin Water Wizard housing
®to camera housing Nikonos strobe connector
®
®Pocket Wizard PLUS III in Water Wizard housing
®to one Ikelite strobe
IKELITE4102.15
®IKELITE4102.03
®
IKELITE4104.31
®
To remote control bulkhead
WATER WIZARD
CANADAMade in
WATER WIZARD
CANADAMade in
PLUS III
MODE
TEST
A B
C D
CH 17
REMOTETRIGGERSYSTEM
®Pocket Wizard PLUS IIIin Water Wizard housingused as receiver
StandardRemote Grip
Pocket Wizard PLUS IIIin Water Wizard housingused as transmitter
®
Pocket Wizard PLUS IIIin Water Wizard housingused as receiver
®
Range of over 100m/ 325ftwith a clear line of sight
# 18738 Housing remote control bulkhead*
To Camera remote control terminal
Nikon 10 pins Canon 3 pins
# 19310 REMOTE CORD
# 19311 REMOTE CORD
Standard Remote Grip is available in kit
*Remote Bulkhead connector bulkhead supplied
19300 19302 19304* 19305*
WATER WIZARD
WATER WIZARD