tech support: 503.693.1918 www ... dune buggies, and custom vehicles. please look at keep it...
TRANSCRIPT
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 1 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
1
WIRE SYSTEM
WWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
1 2
3
ULTRA SMALL 12 PANEL WIRE SYSTEM IMPORTANT: The below instructions
are referring to a general installation. Your vehicle may very from the vehicles
described in these instructions use the diagrams that best describe your vehicle.
Mounting the fuse panel.
The best place to mount the fuse panel is in a flat dry location away from any heat source near the steering column. It is important to note that you should avoid running or mounting wire away from any moving parts such as: brake pedal, gas pedal, linkage controls, and steering controls. Once mounted, find a location on the firewall and drill a 1 1/4" hole to run all needed wires into the engine compartment of the vehicle.
Final Installation:
By this time all wires should be connected or terminated and secured to your vehicle. To start your vehicle for the first time follow these easy steps:
1.Turn off all accessories.2. Close all doors, hood, and trunks.3. Place the ignition switch in the "OFF" position.4. Check to insure there is a fuse on the starter wire.5. Connect the negative battery cable to the battery.6. Check for current draw by connecting one side of a test light to the positive cable, and the other end to the positive side of the battery. If the light goes on you have a either a short or an accessory drawing power. To find the short remove each wire until the light goes out. If you have a dim or no light then it's safe to hook up the positive cable. 7. Test the system and all accessories.
PROCOMP12PROCOMP12B
CHECKLISTNo.
Terminal 2 Fuse Size Output 1No.Terminal 1 Color RELOCATE NOT USED
1 Black
2 White
3 Purple
4 Brown
5
6
7
15
White
Blue
Pink
GrayRed16
17
18
19
20
21
8
9
10
11
12
13
14
22
23
24
25
26
28
21
N/A
Yellow
Green
N/A
Blue/White
20amp
15amp
15amp
20amp
30amp
30amp
30amp
20amp15amp
Not Used
10amp
5amp
Not Used
30amp
Heater
Gauges
Signal Sw
Wiper
Power ACC
ACC1
Heater/AC
RelayBrack Sw
N/A
Spare
Hazard/Spare
N/A
ACC2
Please read the following instructions carefully.
This kit does not include all the wire and connectors you need to wire up a complete vehicle. This wire harness kit is designed to replace your fuse box and main wire harness only. The wire that come out of the fuse box is designed to go directly to your vehicles existing switches and connectors. You will use your factory harness, or supply your own wire to complete the rest of the wiring after the switch or connector.The instructions include basic wiring diagrams to show how to integrate this harness to standard vehicle wiring system. The diagrams are for reference only and do not indicate how your vehicle is wired. The diagrams also show other wires and components that are not included in your kit.This kit is ideal for basic vehicle wiring for Rat Rods, Hot Rods, Street Rods, Dune Buggies, and Custom Vehicles. Please look at Keep It Clean's Pro Comp Series of wire panel systems if you are looking for a complete wire harness system that includes all the wires and switches need for a full install.
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 2 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
2
Please refer to page 3 for these wiring suggestion diagrams.
Included in Kit:
Not Included In Kit:
IGN Switch Input (yellow)
Brake SW (red)
Spare (yellow)
Hazard/Spare (green)
Battery It (red)
ACC2 (blue/white)
IGN ACC (yellow)
Wiper (brown)
Power ACC (white)
Heater (black)
Relay Output (gray)
Signal SW (purple)
Gauges (white)
87
86 85
30
87A OUTPUT
INPUT
ACC1 (blue)
Heater/AC (pink)
22 23 24 25 26 27 28
15 16 17 18 19 20 21
8
Whi
te (g
roun
d)
9 1011
12 13 14
1 2 3 4 5 6 7
+ –
12AWG
18AWG
20AWG
16AWG
12AWG
12AWG
12AWG
14AWG
14AWG
12AWG
16AWG
16AWG
18AWG
18AWG
18AWG
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 3 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
3
Wiper Switch Circuit
Brake Switch Circuit
Gauge Circuit
Heater/A.C. Circuit
Turn Signal Circuit
Hazard Circuit
Wiper Switch Wiper Motor
Brake Lights
WIPER (brown)
Brake Switch
BRAKE SW (red)
GAUGES (white)
Heater Switch
HEATER (black)
SIGNAL SW (purple)
HAZ/SPARE (green)
Heater Blower Motor
A.C. Circuit
A/C Switch
A/C (pink)
A/C Blower Motor
Rear Signals
FrontSignals
Signal Switch
Hazard Switch Rear Signals
FrontSignals
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 4 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
4
HEA
DLIG
HT PW
R [G
ray]
DO
ME &
INTER
IOR LG
T RETU
RN
DA
SH LIG
HTS
F PARK
LGTS
LATE STY
LE GM
PARK
LGTS
DIM
MER
SW
R PA
RK
LGTS [F]
HI B
EAM
[H]
LO B
EAM
[G]
KEY
ACC [Yellow
Input]
STARTER
[E]
COIL [A
]IG
NITIO
N
BA
TTERY [R
ed Inp
ut]BA
TIGN
ACC
ST
FUEL
METER
TEMP
METER
OIL
METER
VO
LTM
ETER
TACH
OM
ETERSPEED
OM
ETER
LFT TURN IND
RT TURN IND
GAUGE POWER [WHITE]
FUEL GAUGE [from sender]
TEMP GAUGE from sensor [D]
TACHOMETER [Input B]
OIL PRESS. GAUGE [Sensor C]
DASH LIGHTS
HIGH BEAM IND
DASH S
ECTIO
N
For R
efe
rence
Only. W
ires n
ot in
cluded.
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 5 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
5
DOM
E LIGH
T
REV LIGH
T SW
REV LIGH
T
BRAKE LIG
HT
FUEL PU
MP
R PARK [light [ F
]
LR TURN
RR TURN
DOM
E LIGH
T
THIRD BRA
KE LIGH
T
TRUN
K LIGH
T
FUEL PU
MP
LICENSE PLATE LIG
HT
LR PARK
LR BRAKE
REV LIGH
T
REV LIGH
T
LR TURN
RR PARK
RR BRAKE
RR TURN
RR TURN
SIGN
AL
FAN
RF TURN
LF TURN
PARK [light [ F
]
LOW
BEAM
[ G]
HIG
H BEA
M [ H
]
HO
RNH
ORN
LF HEA
DLIGH
T
LF PARK
LF TURN
RF HEA
DLIGH
T
FAN
RF PARK
RF TURN
Rear
Front
FRO
NT &
REA
R D
IAG
RAM
S
For R
efe
rence
Only. W
ires n
ot in
cluded.
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 6 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
6
F234
ALT EXCITO
R A
LT-STARTER
Charg
ing S
yste
ms
EARLY
LATE
HIG
H O
UTP
UT W
IRE
STARTER
RS
+ñ
GM
SPEC
IFIC D
IAG
RAM
S
For R
efe
rence
Only. W
ires n
ot in
cluded.
COIL PO
S
TACH
OM
ETER [ B]
DIST
COIL
RESISTOR
STARTER
RS
+-
GM
Sta
ndard
Ignitio
n (P
OIN
TS TY
PE)
Engin
e C
onnectio
ns
+ñ
HEI
OIL SENDING [C]
COIL POS [A]TACHOMETER [B]
CHOKE
TEMP SENDING [D]
STARTER [E]
STARTER
FRON
T
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
MO
PAR S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Fo
r Refe
rence
Only. W
ires n
ot in
cluded.
Charg
ing S
yste
ms
HIG
H O
UTP
UT W
IRE
STARTER
RS
+ñ
BAT
FLD
FLDIG
N
EARLY
LATE
ALT EXCITO
R\A
LT POW
ER
BAT
FLD
FLD
ELECTRO
NIC
REG
ULA
TOR
ELECTRO
NIC
REG
ULA
TOR
ALTER
NATO
R
ALTER
NATO
R
Mopar Ignition (START/RUN)
IG
BAT
ST SGL
COIL POS [A]
STARTER [E]
TACHOMETER [B]
DIST
COIL
RESISTOR
STARTER
S B
+ -
+ ñ
NEUTRALSAFETY SWITCH
STARTERRELAY
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 7 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
7
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
MO
PAR S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Fo
r Refe
rence
Only. W
ires n
ot in
cluded.
Engin
e C
onnectio
ns
IG
BAT
ST SGL
+-
COIL POS [A]
TACHOMETER [B]
CHOKE
STARTER [E]
TEMP SENDING [D]
OIL SENDING [C]
DIST
NEU
TRAL
SAFETY
SW
ITCH
STA
RTER
RELA
Y
STARTER
SB
+ñ
COIL
FRON
T
Mopar Ig
nitio
n (ELEC
TRO
NIC
)
IGN
ITION
RESISTOR
DIST
COIL
+-
COIL PO
S
TACH
OM
ETER [white]
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 8 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
8
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
FORD S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Fo
r Refe
rence
Only. W
ires n
ot in
cluded.
Charg
ing S
yste
ms
ALT EXCITO
R A
LT-STARTER
ALTER
NATO
R
REG
ULA
TOR
STAN
DARD W
IRE
I A S F
S
F BA
T
HIG
H O
UTP
UT W
IRE
STARTER
RELA
Y
ALTER
NATO
R
+
ñ
STARTER
Ford
Ignitio
n
FROM
NEU
TRAL
SAFETY SW
ITCH
STARTER
RELA
Y
ALTER
NATO
R
+
ñ
STARTER
SI
COIL PO
S [A]
TACH
OM
ETER [white]
DIST
COIL
RESISTOR
+-
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 9 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
9
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
FORD S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Fo
r Refe
rence
Only. W
ires n
ot in
cluded.
Ford
Ignitio
n (ELEC
TRO
NIC
) STARTER
RELA
YSI
COIL PO
S [A]
[white]
[red]
[green][orange][purple][black]
TACH
OM
ETER [B]DIST
COIL
+-
ELECTRO
NIC
IGN
ITION
MO
DULE
Engin
e C
onnectio
ns
STARTER
RELA
Y
SI
+
ñ
COIL
+-
DIST
COIL POS [A]TACHOMETER [B]
CHOKE
STARTER [E]
TEMP SENDING [D]
OIL SENDING [C]
FRON
T
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 10 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
10
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
Steering Column Information For Reference Only
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 11 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
11
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
16AWG Br
H26
H25
16AWG V
Color
D8
No.
16AWG
Spec.
V HORN/FLASHER
HAZARD
F1
E2 E1
F1
D8
F1
H25
B1
B2
H11
H12
B2
C1
©2012 The Hoffman Group L.L.C. All rights reserved. ProComp Basic - 12 of 12 Version 3 12/14/12
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
12
WWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
OPTIONAL ACCESSORIES
USE THESE EXCELLENT ADD-ON ACCESSORIES TO ENHANCE YOUR WIRE PANEL SYSTEM
• SIMPLE INSTALLATION• LONG LIFE AND RELIABLE OPERATION• BACKED BY A LIMITED LIFETIME WARRANTY
IGNITION SWITCH DIMMER SWITCH
BATTERY KILLHEADLIGHT SWITCH
RELAYS
Keep it Clean's headlight switch offers CAD design engerneering to provide a smooth operation! Keep It Clean's unique screw on design makes installation a snap, and offers a clean smooth look.
Keep It Clean's battery kill switch offers maximum performance and easy operation. The BATK CAD design offers a long life of smooth operation. Backed by a limited lifetime warranty.
Keep It Clean's heavy duty 40-amp relays are the best choice for any sort of 12-volt wiring project. Single-pull/Double-throw springs mean that your RA-1000 relays will never get stuck or short out on you. Combine the RA-1000 relay with the RAS relay socket, and you've just saved yourself hours of wiring time!
FLEX LOOM
Give your installations the ultimate professional appearance. Split Looms keep all your wires in place and protected from the elements, as well as giving any wiring job that final touch.
Keep it Clean's dimmer switch offers CAD design engerneering to provide a smooth operation! Keep It Clean's unique floor mount designmakes installation a snap, and offers a clean smooth look.
Keep it Cleans ignition switch offers CAD design engineering to provide a smooth operation! Keep It Clean's unique screw on design makes installation a snap, and offers a clean smooth look. Each switch comes w/ 4 heavy duty copper terminals w/ locking nuts for Ignition, Accessory, Battery, & Starter.