team submittalcustom ahu

7/21/2019 Team Submittalcustom Ahu

1/62

Phone: (909)823-1957

Fax: (909)823-6204www.teamairinc.com

Submittal PackageFor

BB II GG LL OO T T SS CC UU SS T T OO MM

AHU 1

Team Air Job # 518-01215


2/62

IInn dd ee xx

Section 1: Construction Notes

Section 2: Engineering Data

Spec ifica tions: AHU-1

2.1.1 Mechanical Drawing2.1.2 Electrical Schematic2.1.3 Component Detail Sheet

2.1.4 Fan Selection2.1.5 Pressure Drop Calculations2.1.6 Coil Selections

Section 3: Revision Notes

Section 4: Catalog Sheets

4.1 Fans & Motors4.2 Filters4.3 Dampers 4.4 Insulation4.5 VFD4.6 Lights4.7 Doors4.8 Construction Details


3/62

Section 1Construction Notes


4/62

Liner Material (Floor): 20 Ga. Bright ASTM A90 and A653 G60 Galvanized.

Casing Material: 16 Ga. Paint grip galvanized ASTM A653.

Standard paint color is Team Air Gray. If a different color is necessary please provide paint color before releasedto production.

OPENINGS:

PAINT:

Insulation (Floor): 2 Foam R 13

Liner Material (Walls/Roof): 20 Ga. Bright ASTM A90 and A653 G60 Galvanized.

The base is 6 Structural C channel, ASTM A572 GRADE 50, with 2" x 4" tubular structural cross supports in 24"center.

Insulation (Fan Section):2 Foam R 13

CONSTRUCTION DETAILS AND SPECIFICATIONS

UNIT CONSTRUCTION

BASE:

Floor Material: 10 Ga. Aluminum tread plate ASTM A653.The floor will be a drain pan type with a 2" flange around the unit with a drain connection.

LINER:

INSULATION:

Insulation (Doors): 2 Foam R 13

Insulation (Casing): 2 Foam R 13

Insulation (Roof): 2 Foam R 13

BIG LOTS CUSTOM

FLOOR:

CASING:

ROOF:Roof Material: 16 Ga. Paint grip galvanized ASTM A653.

Paint is certified for 2000 hours salt spray test per ASTM B117.


5/62

DRAIN PANS:

For motor information see motor data sheet in submittal catalog data section.

Drain pans are in the cooling coil section

Filter gauge is Dwyer 2001.Filter frame is 16 ga. Galvanized.

All dampers are provided and installed by Team Air.Dampers:

For more fan information see fan selection data sheet in submittal catalog data section.

Please refer to the electrical drawing for more details.

2", MERV 8, 30% pre filtersPRE FILTERS:

BIG LOTS CUSTOM

Direct drive fans, arrangement 4 are provided with spring isolated supply fan and motor assemblies. This is a rigid, galvanized steel base supported at four (4) corners on free floating spring isolators with seismicrestraints.

Motors are to be ODP, premium ellficiency, and inverted rated.MOTORS:

Fan assemblies are mounted on spring isolators to reduce transmission of the motor vibration to the unitstructure, spring isolated assemblies offer a highly efficient means of reducing transfer of vibration to thebuilding structure by isolating the energy at its source.

SUPPLY FANS:

Premium efficiency motors will be wired to VFD's.

VFD:

COOLING COILS:

Team Air will provide mount and wire VFD's.

Coils are certified and rated with accordance to AHRI standard 410Casing material to be 304 stainless steel.

Dampers are manufactured by Tamco 1000 series

Please refer to the cooling coil selection for more detail


6/62

UNIT LISTINGS:Unit is ETL listed.

ELECTRICAL PANEL:

LEAK AND PRESSURE TEST:Unit is constructed not to exceed deflection is L/200 at 10 of static pressure.

UL 508 listed industrial control panel.

Unit is contructed not to exceed the maximum leakage rate of 1% of the total unit CFM @ 10" of static pressure.

BIG LOTS CUSTOM


7/62

Units are designed and build in accordance with the followin gs:

NEC National Electrical Code

NFPA National Fire Protection Association

UL Underwriters LaboratoryInc

NEMA NationalElectricalManufacturersAssociation


8/62

Section 2Engineering Data


9/62

Unit SpecificationsAHU-1


10/62

1

9

6

66

156

147

D X C O I L

19W AD 19W AD

F.S 73 14

N.S. 761

4

30 30846 6

19W AD

2 3 4 5 6

19W AD

LOUVEREDREMOVABLE

PANELREMOVABLE

PANEL

8

96

25 12

25 12

30

24

18

10

CONNECTIONSON THIS SIDE

44 7/8 [1139.70]

144

CONNECTIONSON THIS SIDE

30

LOUVEREDREMOVABLE

PANEL

7

BIG LOTS CUSTOM

CAPACITY:

DRAWING DATE:

DESCRIPTION:

SCALE:

DRAWING BY:

JOB No: TAG:

JOB NAME:

REV DESCRIPTION

REVISIONS

APPROVEDDATE BIG LOTS CUSTOM

518-011215

01-20-15

MECHANICALDRAWING

MYA LAZO

24,000 CFM AHU-1NTS

TEAM AIR INC.AIR CONDITIONING EQUIPMENT

14562. SAN BERNARDINO AVE FONTANA, CA 92335PHONE: (909)823-1957

FAX: (909)823-6204WWW.TEAMAIRINC.COM

OUTDOOR

APPLICATION:

APPROX UNIT WEIGHT:

NTS

SCALE:

7,278 lbs

1 OSA DAMPER

2 RA DAMPER3 MERV 8, 2" FILTERS4 DX COIL5

GAS FURNACE6

1 1/4" DRAIN CONNECTION

7

SUPPLY FAN

PRELIMINARY DRAWING

SUPPLY VFD

8

7,278 LBS

WEIGHT

1 REVISED THE RA & SA TO BOTTOM OPENINGS ML01-28-152 LABELED CONNECTION SIDE FOR GAS FURNACE ML02-06-15

9

2001 FILTER GAUGE

3 REVISED FANS, RAINHOODS & GAS FURNACES ML02-11-15

10

VENT (BY OTHERS)

ROOF CURB MOUNTEDANGLE NEEDED


11/62

BASE HEIGHT6

CURBHEIGHT

14"

UNITLENGTH

156

UNITWIDTH

147

CURBWIDTH

140 12

SEE DETAIL "A"

149 12314 3

14

314

314

25 12

96

25 1

2

25 12

96

25 1

2

66

BIG LOTS CUSTOM

CAPACITY:

DRAWING DATE:

DESCRIPTION:

SCALE:

DRAWING BY:

JOB No: TAG:

JOB NAME:

REV DESCRIPTION

REVISIONS

APPROVEDDATE BIG LOTS CUSTOM

518-011215

01-20-15

MECHANICALDRAWING

MYA LAZO

24,000 CFM AHU-1NTS

TEAM AIR INC.AIR CONDITIONING EQUIPMENT

14562. SAN BERNARDINO AVE FONTANA, CA 92335PHONE: (909)823-1957

FAX: (909)823-6204WWW.TEAMAIRINC.COM

OUTDOOR

APPLICATION:

APPROX UNIT WEIGHT:

NTS

SCALE:

7,278 lbs

7/8"

7/8"

2"

PROPOSED ROOF CURB LAYOUT

7,278 LBS

WEIGHT:

1 REVISED THE RA & SA TO BOTTOM OPENINGS ML01-28-15

ROOF CURB MOUNTEDANGLE NEEDED


12/62

GENERAL SPECIFICATION SHEET

TAG: TAG: TAG: TAG: TAG:QUANTITY: QTY: MFG: QUANTITY: QUANTITY:MFG: MFG: EFFICIENCY: SIZE (HXL): SIZE:DRIVE: CLASS: TAG:

SIZE: QUANTITY:SIZE: SIZE:DEPTH:GAUGE: MFG:FILTER FRAME: SERIES:CONF: BLADES:FILTERS BY: JACKSHAFT:

TAG: CLIPS BY:QUANTITY:MFG:

OPPOSEDNO

RAII24X24 (10)12X24 (2)

TAMCO1000

200116 GA. GALV.

1

2"

SUPPLY TOTAL STATIC PRESSURE:

DIRECT

PLEASE REFER TO FAN REPORT FORMORE INFORMATIONPLEASE REFER TO FAN CURVE FOR

MORE INFORMATION

1

30H X 96W

PLEASE REFER TO COILSELECTION FOR MORE

INFORMATION

54H X 130L

DAMPERSOSA

30H X 96W

3.5SUBMITTED BY:

SUBMITTAL DATA SPECIFICATIONS

FILTERSMERV 8

N/ MYA LAZO

DATE: REVISION:

1/20/2015 1PAINT (POLYURETHANE):

FACELOADGAS FURNACE

HDA300_B

GENERAL INFORMATION

YES24,000 N/

JOB NAME: JOB NUMBER: UNIT TAG:

BIG LOTS CUSTOM 518-011215 AHU-1TOTAL UNIT CFM: SPLIT/QTY:RETURN TOTAL STATIC PRESSURE:

1 1 1TWIN CITY BALDOR

CAMFIL FARR30%

FAN SECTION MOTOR COIL SELECTIONSUPPLY SUPPLY DXC

2HEATCO

PLEASE REFER TO HEATCOSELECTION FOR MORE

INFORMATION

TEAM AIRTEAM AIR


13/62


14/62

C F M ( i n 1 , 0 0 0 s )4 8 12 16 20 24 28 32

SP

SYSTEM CURVE

S T A T I C

P R E

S S U R E

( i n

. w g

)

1.5

3.0

4.5

6.0

7.5

9.0

10.5

12.0

BHP

B R A K E H O R S E P O W

E R

4

8

12

16

20

24

28

32

24,000Total CFM:3.5 in.wgSP:

2831RPM:13.28 / fanBHP:

3,860Outlet Velocity:

0.075Density:Corrected for:2 fans operating insystem

Total PackageSound Power Level

In/OutOctave94 / 93194 / 932

103 / 1043105 / 107495 / 100591 / 99690 / 96785 / 898

in db re 10- watts2/13/2015Page: 1 of 1

Customer: W/AJob ID: 518-011215

Fan Tag: AHU-1 supply fanModel: 200 EPFN

104T W I N C I T Y F A N A N D B L O W E R P E R F O R M A N C E C U R V E


15/62

Customer: W/A February 13, 2015Job Name: Big Lots Custom Page 1 of 3Job ID: 518-011215

Fan Description Fan Performance Motor Data

Tag . . . . . . . . . AHU-1 supply fan Total CFM . . . . . . . . . . . . . 24,000 HP . . . . . . . . . . . . . . . . . . . . . . . 15Quantity . . . . . . . . . . . . . . . . . . . . 2 CFM/fan . . . . . . . . . . . . . . . 12,000 RPM . . . . . . . . . . . . . . . . . . . 3600# fans per system . . . . . . . . . . . . 2 Operating SP (in.wg) . . . . . . . . 3.5 Voltage . . . . . . . . . . . . . . . . 460VType . . . . . . . . . . . . . . . . . . EPFN Standard SP (in.wg) . . . . . . . . 3.5 Phase . . . . . . . . . . . . . . . . . . . . . 3Size . . . . . . . . . . . . . . . . . . . . . 200 RPM . . . . . . . . . . . . . . . . . . . 2831 Hz . . . . . . . . . . . . . . . . . . . . . . . 60Width . . . . . . . . . . . . . . . . . . SWSI Tip Speed (fpm) . . . . . . . . 14,823 Enclosure . . . . . . ODP - Premium

Arrangement . . . . . . . . . . . . . . . . 4 Oper. BHP/fan . . . . . . . . . . . 13.28 Frame . . . . . . . . . . . . . . . . . . 215TClass . . . . . . . . . . . . . . . . . . . . . III Standard BHP/fan . . . . . . . . 13.28 Design VFD Op. Freq.(hz) . . . . 48Rotation . . . . . . . . . . . . . . . . . . CW Tot. Oper. BHP . . . . . . . . . . 26.55

Discharge . . . . . . . . . . . . . . . HOR Tot. Standard BHP . . . . . . . 26.55Wheel diameter (in.) . . . . . . . . . 20 Outlet area (sq. ft) . . . . . . . . . 3.11Drive method . . . 60 Hz direct drive Outlet Velocity (fpm) . . . . . . 3,860Percentage width . . . . . . . . 100% Temperature (F) . . . . . . . . . . . . 70Percentage diameter . . . . . . 100% Altitude (ft) . . . . . . . . . . . . . . . . . . 0

Density (lb/ft) . . . . . . . . . . . 0.075Max RPM for Class . . . . . . . . 3438Static Efficiency . . . . . . . . . . 49.73Total Efficiency . . . . . . . . . . 62.92

Modifiers

2 fans operating in system

Sound

Individual Sound Power Levels in dB re. 10 -12 Watts:

Octave Bands 1 2 3 4 5 6 7 8 LwALevel at Inlet 91 91 100 102 92 88 87 82 101Level at Outlet 90 90 101 104 97 96 93 86 104

Total Package Sound Power Levels in dB re. 10 -12 Watts:

Octave Bands 1 2 3 4 5 6 7 8 LwALevel at Inlet 94 94 103 105 95 91 90 85 104Level at Outlet 93 93 104 107 100 99 96 89 107


16/62

Customer: W/A February 13, 2015Job Name: Big Lots Custom Page 2 of 3Job ID: 518-011215

Definitions:

LwA The overall (single value) fan sound power level, 'A' weighted.

dBA The environment for each fan installation influences its measured sound value, therefore dBA levels cannot be guaranteed. Consult AMCA Publication 303 for further details.

A fan's dBA is influenced by nearby reflective surfaces.

Accessories Included

EPFN 200, Class III, Arrangement 4 Bare fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 lb.

Wheel - Aluminum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 lb.15 HP, 3600 RPM, 460V, 3Ph, 60Hz, Motor, ODP - Premium, 215T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 lb.Mount TCF Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 lb.

Total Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 lb.


17/62

SUPPLY FAN

ITEMSDelta,In. wc

ESP 1.50

PRE FILTERS 0.31

DX COIL 0.45GAS FURNACE 0.96

OSA DAMPER 0.02

RA DAMPER 0.02

AVAILABLE STATIC PRESSURE: 0.24

FAN TOTAL STATIC PRESSURE: 3.50"

PRESSURE DROP SUMMARY

NAME: BIG LOTS CUSTOM

UNIT TAG: AHU-1


18/62

Customer: Date: 1/19/2015Contact: From: Mya LazoTelephone: Company: Team AirCell: Return Tel:Fax: Return Fax:Job:Quote #:

Construction Air SideItem: AHU-1 DXC Air Flow (Sft^3/min) 24000.0Coils Per Bank: 1 Altitude FT: 0.00Tube OD IN: 5/8 Ent. Air DB/WB F: 80.00 / 67.00

Style: EN Lvg. Air DB/WB F: 0.00 / 0.00Fins Per Inch: 8 Total / Sensible MBH: 720.0 / 0.00Rows: 6 Max Air PD "H2O: 1.00Fin Surface: Optimize ABCFin Height (IN): 54.00 Refrigerant SideFinned Length (IN): 130.0 Refrigerant: 410ATubing Mat. (IN): 0.020 Copper Super Heat F: 8.00Fin Mat. (IN): 0.0075 Aluminum Saturated Suction Temp F: 45.00

Circuiting: Optimize Liquid Temp F: 110.0Face Area (SQ FT): 48.75

O U T P U T D A T A Most Economical Specified CoilCoil 1 Coil 2 Coil 3 Coil 4 Coil 5 Coil 6

Model Number: 5EN0806A Air Velocity: (Sft/min) 492.3Total Capacity: MBH 888.3

Sens. Capacity: MBH 601.2Lvg. Air DB: F 56.81Lvg. Air WB: F 55.26Standard APD "H2O 0.45Code 18/19: 8027/50Code 18/19_2: N/ASuction Conn.: IN (1) 2.625Distributor Conn 1: IN (1) 1.625

Distributor Conn 2: IN N/ARefg. PD: lbf/in^2 6.64Refg. Velocity: ft/min 1688.2Internal Volume: in^3 8716.0Weight: lbm 762.1Notes: CMW

HEATCRAFT EVAPORATOR SELECTION 7.05.36.999


19/62


20/62

Section 3Revision Sheet


21/62

Section 4Catalog Sheets


22/62


23/62

The standard E-Series plenum fans already offers a low vibra-tion design, but when faced with stringent vibration require-ments, Twin City Fan & Blower offers patent pending UltraLow Vibration (ULV) designs with a full spectrum dynamicbalance.

Along with the ULV balance guarantee, a full vibration reportis provided that includes a summary of banded spectrum lim-its, spectrum plots on 3 axes, a waterfall (cascade) plot, a time

waveform plot, and a transient capture (coast down) plot.

Space is often a key consideration in the selection of plenumfans, making the compact Arrangement 3 configuration verypopular.

The Arrangement 3 configuration is constructed with a bear-ing and bearing bar in the inlet, which will affect fan per-formance. These performance affects should be taken intoaccount to ensure that your system functions as designed

Twin City Fan & Blower, the worlds largest supplier of ple-num fans, now offers the completely redesigned E-Series, thefirst plenum fan to be AMCA licensed for sound and air inboth an Arrangement 1 and 3 configuration.

The E-Series offers the flexibility of two plenum fan designs, with each model offering its own unique performancecharacteristics. While every E-Series fan is highly efficientand quiet, you can choose an E-Series design option thatoptimizes the performance requirements most important toyour application.

The model EPF features a highly effi-cient and cost effective, nine-bladedairfoil wheel design. The high efficien-cy of the EPF will often allow theuse of smaller fans without increasingpower requirements. The EPF is an

Arrangement 3 design.

The model EPFN features the same highly efficient, nine-bladed airfoil wheel design as the EPF, but is available in

Arrangement 1 or 4 designs without inlet obstructions.

The Better Sound Quality model EPQfeatures a twelve-bladed airfoil wheeldesign that flattens the sound spectrumand reduces the dominance of puretones. The EPQ is an Arrangement 3design.

The model EPQN features the same Better Sound Quality,twelve-bladed airfoil wheel design as the EPQ, but is availablein Arrangement 1 or 4 without inlet obstructions.


24/62

The EPQ/EPQN plenum fans offers unique performancefeatures that are beneficial for many sound sensitive and

higher pressure applications. The EPQ/EPQN features a twelve-bladed airfoil wheel versusthe nine-bladed wheel of our type EPF/EPFN plenum fansor eight- to ten-bladed wheels with most other competition.

The "Q" in the EPQ/EPQN designation stands for BetterNoise Quality. Noise quality is a subjective description fornoise that is less objectionable.

Looking at the sound comparison, you will notice that the type

EPQ/EPQN offers noise (SPL) that is more equally distrib-uted across all frequencies. This can be more pleasant to hearthan the sound characteristics of a nine-bladed design. Fansare often dominated in noise by the noise occurring at theblade pass frequency. (Blade pass frequency = RPM x Numberof blades/60.) Noise quality is improved by reducing the dif-ference in amplitude between the blade pass amplitudes andthe neighboring frequency amplitudes. The increased higherfrequency sound power levels on the twelve-bladed wheelsmask the blade pass frequency offering a better sounding fan.

Although the overall A-weighted sound power levels of thenine-bladed EPF/EPFN fans are slightly lower, the sound"quality" of the twelve-bladed EPQ/EPQN fans may bedesirable for the application.

A higher blade pass frequency allows for easier attenuation ofthe noise especially when installed inside an air handler cabi-

will move the blade pass frequency from the second octaveband to the third octave band. Acoustic silencers will normally

perform about 10 dB better in the third band.In addition to sound considerations, there are also addi-tional benefits to using the EPQ/EPQN at higher pressures.Selections over 8" wg static pressure are often near the peakpressure of the fan. The additional blades give a higher peakpressure and also add stability to the fan. Twelve smallerpassages through the fan wheel are more resistant to flowdisturbances on the inlet than nine larger passages. The EPQ/EPQN is thus more resistant to system effects when operating

at high pressures and the higher inlet velocities that accom-pany these selections.

Plenum fans are unhoused fans designed to operate inside offield-fabricated or factory-built air handling units.

The fan wheel pressurizes the entire surrounding air plenumin which the fan is installed, allowing air ducts from any direc-tion to be directly connected to the air handling unit enclosure.

This design generally saves space by eliminating the fan hous-ing, transitions, and diffusers within the air handling unit.

Plenum fans have found a ready acceptance in the air con-ditioning industry. In addition, the construction versatility,adaptability in the direction of the discharges, suitability forinternal isolation and application of sound panels, and gener-ally lower cost makes it a very popular fan arrangement.

Saves Space There are no housings, transitions, or diffusers

within the air handling unit.

Efficiency Plenum fans can be as efficient or more efficientthan scroll type fans at specific operating points towards thebottom of the fan curve.

Lower cost Plenum fans are less expensive than scroll typefans.


25/62

High efficiency, non-overloading airfoil wheels are providedon all sizes and arrangements.

Aluminum wheels using extruded aluminumblades are standard to size 245 on arrangement 1 and 3 fans,and available as an option on larger sizes. Steel wheels arestandard on sizes 270 and larger.

Aluminum wheels using extruded aluminum bladesare standard to size 600 on direct drive arrangement 4 fans,a popular choice for applications requiring precision balanceand improved reliability.

Heavy-gauge, spun steel inlet cones are closely matched to the

wheel intake rim to ensure efficient and quiet operation.

Frames are constructed of heavy-gauge steel, continuously

welded at all connections for maximum strength and rigidity. The cross frame bearing support is designed for maximumstability and load distribution.

Shafts are AISI Grade 1040 or 1045 hot-rolled steel accuratelyturned, ground, polished, and ring-gauged for verification.Shafts are generously sized for a first critical speed of at least1.43 times the maximum speed for the class.

Either ball (adapter mount) or spherical roller, heavy-duty,self-aligning, pillow block type bearings are provided. Bearingselection is based on minimum L-10 life of 80,000 hours.Considering the long life offered with our standard bearingselections, we do not recommend upgrades to split-roller bear-ings due to their large size, especially on Arrangement 3 fans.

Horizontal configurations are designed to be flex-connected

to the perimeter of the square panel without the addition ofan inlet collar.

are standard to size 600 on direct drive arran ement 4 fansa o ular choice for a plications requiring precision balancean improve re ia i ity.

Aluminum wheels usin extruded aluminum blades


26/62

Vertical Arrangement 3 is available with two different motor mounting options: slide base type (Arrangement 3VS) and adjustablemotor base (Arrangement 3VA). Due to limited belt center range, NEMA slide base option is available on sizes 182 and largeronly. A heavy duty Twin City Fan & Blower designed adjustable motor base is available for all fan sizes.

Models EPF and EPQ.

Arrangement 3VS is available in Class I and II with motor slide base for sizes 182 to 542. See dimensional drawing on page 33.

Arrangement 3VA with pivot motor base is available in Class I and II for sizes 122 to 542. See dimensional drawing on page 33.

Unless specified otherwise, units will be built for vertical up airflow.

Arrangement 3SM is designed to provide an economical and space-saving meansto supply plenum fans with motors mounted to the side of the fan frame. A motorslide base allows for quick and easy belt adjustments.

Models EPF and EPQ.

Class I and II available in sizes 165 to 600. Motor limited to maximum framesize shown on drawing.

See dimensional drawing on page 31.

Direct drive Arrangement 4 mounts the fan wheel directly onto the motor shaft. This arrangement provides a compact fan/motor unit which eliminates belt resi-due and requires less maintenance than other arrangements.

For these reasons, Arrangement 4 plenum fans are widely used in cleanroom,pharmaceutical, and other critical applications.


27/62

Performance Data:ODP - Open Drip Proof, Rigid Base230/460 Volts, Three Phase, 1 through 100 Hp

Open Drip ProofPremium Efficient Motors

Amps @ High V Full Load Efficiency % Power Factor % Bearings Conn.Catalog Full Locked Torque Full Full Volt C Diag.

Hp kW RPM Frame No. Load Rotor Lb. Ft. 1/ 2 3/ 4 Load 1/ 2 3/ 4 Load DE ODE Code Dim. No.1 0.75 3450 56 EM 3115 1.4 12.6 1.5 80.4 83.5 84.0 71 80 83 6205 6203 E1 11.06 CD00051 0.75 1740 143T EM 3116T 1.4 9.6 3.0 84.7 86.3 85.5 62 74 81 6205 6203 E1 11.62 CD00051 0.75 1140 145T EM 3156T 1.6 9.4 4.5 82.6 83.1 82.5 52 65 70 6205 6203 E1 13.00 CD0005

1 1/2 1.10 3450 143T EM 3120T 2.1 16.0 2.2 83.9 85.4 85.5 71 80 85 6205 6203 E1 11.12 CD00051 1/2 1.10 1740 145T EM 3154T 2.1 17.5 4.5 85.4 87.1 86.5 56 69 77 6205 6203 E1 12.12 CD00051 1/2 1.10 1170 182T EM 3207T 2.6 14.0 6.76 84.7 87.2 87.5 41 53 62 6206 6205 E1 15.00 CD0005

2 1.50 3450 143T EM 3155T 2.5 22.0 3.0 87.8 88.1 86.5 78 86 90 6205 6203 E1 11.62 CD00052 1.50 1725 145T EM 3157T 2.7 19.6 6.0 87.9 88.3 86.5 64 76 82 6205 6203 E1 13.00 CD00052 1.50 1170 184T EM 3215T 3.5 19.8 8.9 86.0 88.3 88.5 40 52 60 6206 6205 E1 16.50 CD0005

3 2.20 3450 145T EM 3158T 3.7 29.0 4.5 87.1 88.5 87.5 76 85 89 6205 6203 E1 13.00 CD00053 2.20 1760 182T EM 3211T 4.1 32.0 9.0 89.1 90.0 89.5 58 71 77 6206 6205 E1 15.00 CD00053 2.20 1160 213T EM 3305T 4.6 27.0 13.5 88.6 90.3 90.2 48 60 67 6307 6206 E1 16.32 CD00055 3.70 3500 182T EM 3212T 5.6 55.0 7.5 90.5 90.8 90.2 83 90 93 6206 6205 E1 15.00 CD00055 3.70 1750 184T EM 3218T 6.4 48.0 15.0 89.8 90.5 89.5 61 73 81 6206 6205 E1 16.50 CD00055 3.70 1160 215T EM 3309T 7.2 43.0 23.0 89.7 90.0 89.5 56 67 73 6307 6206 E1 18.20 CD0005

7 1/2 5.60 3500 184T EM 3219T 8.4 87.0 11.2 91.3 91.6 90.2 85 90 93 6206 6205 E1 16.50 CD00057 1/2 5.60 1760 213T EM 3311T 10.0 61.0 22.5 89.6 91.0 91.0 61 73 79 6307 6206 E1 16.32 CD00057 1/2 5.60 1180 254T EM 2506T 11.5 68.0 33.4 90.3 91.5 91.7 51 63 70 6309 6208 E1 23.19 CD0005

10 7.50 3500 213T EM 3312T 11.5 98.0 15.0 90.9 92.0 91.7 81 87 90 6307 6206 E1 16.32 CD000510 7.50 1760 215T EM 3313T 12.9 96.0 29.6 90.8 91.8 91.7 61 72 80 6307 6206 E1 17.45 CD000510 7.50 1180 256T EM 2511T 14.3 91.8 44.4 91.0 92.0 91.7 54 65 71 6309 6208 E1 23.19 CD018015 11.20 3525 215T EM 3314T 17.0 143 22.5 91.9 92.3 91.7 80 87 92 6307 6206 E1 17.45 CD000515 11.20 1765 254T EM 2513T 17.7 118 44.6 93.3 93.5 93.0 70 81 86 6309 6208 E1 21.69 CD018015 11.20 1180 284T EM 2524T 19.8 131 66.6 91.4 92.6 92.4 58 70 77 6311 6309 E1 23.81 CD018020 14.90 3510 254T EM 2514T 22.5 144.8 29.9 93.5 93.3 92.4 79 87 90 6309 6208 E1 21.69 CD018020 14.90 1765 256T EM 2515T 23.5 160.8 59.4 92.5 93.2 93.0 71 81 86 6309 6208 E1 21.69 CD018020 14.90 1175 286T EM 2528T 26.0 169 89.1 91.6 92.5 92.4 63 74 79 6311 6309 E1 25.06 CD000525 18.70 3520 256T EM 2516T 28.0 209 37.3 93.0 93.3 93.0 83 89 91 6309 6208 E1 21.69 CD000525 18.70 1770 284T EM 2531T 30.0 190.3 74.1 93.4 94.2 94.1 69 79 83 6311 6309 E1 23.81 CD000525 18.70 1180 324T EM 2532T 31.0 222 111 93.3 93.9 93.6 65 76 80 6312 6311 E1 26.69 CD018030 22.40 3540 284TS EM 2534T 34.0 229 44.5 93.3 93.8 93.6 82 87 89 6311 6309 E1 22.44 CD000530 22.40 1770 286T EM 2535T 35.0 223.6 88.9 93.6 94.2 94.1 72 82 85 6311 6309 E1 25.06 CD000530 22.40 1180 326T EM 2536T 37.0 267 133 93.3 93.9 93.6 69 78 82 6312 6311 E1 27.69 CD018040 30.00 3540 286TS EM 2538T 44.0 315 59.4 94.4 94.6 94.1 84 89 90 6311 6309 E1 23.69 CD018040 30.00 1775 324T EM 2539T 46.0 313 118 94.2 94.8 94.5 72 82 86 6312 6311 E1 26.69 CD018040 30.00 1185 364T EM 2540T 50.0 315 177 93.6 94.2 94.1 65 75 80 6313 6312 E1 29.69 CD000550 37.00 3540 324TS EM 2542T 56.0 353 74.1 93.7 94.0 93.6 81 87 89 6312 6311 E1 25.19 CD018050 37.00 1775 326T EM 2543T 57.0 378 148 94.5 94.9 94.5 75 84 87 6312 6311 E1 27.69 CD018050 37.00 1185 365T EM 2544T 62.0 380 221 93.9 94.4 94.1 66 76 80 6313 6312 E1 29.69 CD018060 45.00 3540 326TS EM 2546T 65.0 493 88.9 94.7 95.0 94.5 86 90 92 6312 6311 F 25.19 CD018060 4500 1775 364T EM 2547T 680 470 177 949 953 950 77 85 87 6313 6311 F 3069 CD0180


28/62


29/62

The best performingpleated panel filter

guaranteed!

30/30 High-Capacity MERV 8 Pleated Panel Filter

The Camfil Farr 30/30 has set the industry standardfor pleated panel filters. With over 45 designenhancements, it continues to provide the industrysbest value for medium efficiency filtration.

Setting the standard by which other pleated filters are judged, modern media manufacturing techniques andproprietary technological advancements ensure thatthe Camfil Farr 30/30 is:

Guaranteed to performat the rated efficiency, orbetter, throughout the lifeof the filter.

Guaranteed to lastlonger than any otherpleated panel filter.

Performing at MERV 8, usinga mechanical particle capture principle, the 30/30 willnot drop in efficiency while in service, as will otherpleated panel filters that incorporate an electret chargeto obtain a MERV 8 value.

Its radial pleat design provides the longest life andlowest average pressure drop, reducing the number offilter changes, so your facility will use less fan powerto move air through the filter.

The high wet-strength beverage frame and weldedwire media backing provide structural integrity in anyHVAC application, virtually eliminating the additionalcosts associated with filter bypass or filter failure.

Available in 1, 2 or 4 deep configurations, the 30/30

is ideal for commercial, industrial, institutional or anyapplication where the ultimate level of protection ofequipment and indoor air quality is a concern.

The Camfil Farr 30/30 has an Energy Cost Index (ECI)of five stars, the highest performance rating available.

Exclusive MERV 8 Perfor mance from Camfil Farr MediaCamfil Farr 30/30


30/62

The 30/30 media is manufactured from a proprietary blend of fibers thatincorporate a mechanical principle of particle capture. The filter does notrequire an electret charge which would dissipate and reduce filter efficiencyafter minimal hours of operation in a system. The media is lofted to a uniformdepth to enhance the depth-loading characteristic and ensure the longest

life of any pleated filter available. The high-loft also offers a lower resistanceto airflow, so fan horsepower required to move air through the filter isminimized. Camfil Farr evaluates the quality of all incoming raw materialsto maintain product integrity as part of a rigorous quality control program.

Welded Wire Grid Maintains Radial Pleat Design

The media is formed into a radial pleat for uniform dust loading and full use of the mediaarea. V-style pleats will blind with bridging contaminant, when loading, preventingfull utilization of the media area and increasing the filters pressure drop, resultingin increased energy usage. A welded wire grid, spot welded on one-inch centersmaintains each radial pleat and maintains media stability through varying airflows.

High Wet-Strength Beverage Board Frame

The high wet-strength beverage board frame, the thickest board in the industry,

creates a stable and non-yielding media pack. Filter bypass is virtually eliminatedbecause the filter fits securely in the filter holding mechanism. The media isbonded to the frame, ensuring that all of the air seen by the filter will be treatedby the filter. Diagonal support members are bonded to each pleat to maintainpleat spacing and add stability to the pack through bridge-style engineering.The 30/30 is guaranteed to 2.0 w.g. of pressure filter without failure. Costlyfilter blowouts and compromising of HVAC system cleanliness is eliminated.

The standard of the industry, by Camfil Farr

Used in many systems as a prefilter, the 30/30 extends the life of final filters by capturing larger contaminant and thereby allowingthe final filters to concentrate on moving smaller particles such as those that are respirable and can cause lung damage The

The highest media weight, more than any otherpleated panel lter, and uniform lofting for high dustholding capacity, ensure that the 30/30 will last longerin any HVAC application.

Rounded radial pleats, instead ofv-shape pleats, allow full usage ofmedia area.

Diagonal support members, glued toeach pleat at its apex, help maintainpleat stability and lter rigidity.

ISO 9001:2000 Certified Quality Contro l

Every 30/30 filter is identified on the frame with a unique manufacturing code that allows us to analyze every component ofconstruction, from raw materials to the point where the product is boxed for shipping. Filters are inspected for structural integrity,so they are capable of operating in the harshest HVAC system conditions. The adhesion of diagonal support members topleat apexes is inspected, so pleat spacing is uniform to provide longer filter life. Each media lot is laboratory tested to confirmconsistent performance and individual filters are submitted from each manufacturing facility on a strict schedule for ASHRAE52.2 testing in our world-class testing facility.

30/30 PERFORMANCE DATA

2 D Filt ( t l fi lt d th 1 75 )


31/62

Part Number Nominal Depth

(inches)Nominal Size

(inches)

Actual Size(inches) Initial Resistance

(inches w.g.) Airflow Capacity

(cfm)Total Media Area

(sq. ft.)Pleats per

Linear FootDepth Height Width

049880-019

2

16 x 16

1.75

15.50 15.50

0.31

890 7.8

15 pleats perlinear foot

049880-008 20 x 10 19.50 9.50 700 6.0

049880-009 20 x 14 19.50 13.50 975 8.3049880-007 20 x 12 19.50 11.88 835 7.4049880-011 20 x 15 19.50 14.50 1045 9.3049880-001 20 x 16 19.50 15.50 1100 9.9049880-013 20 x 18 19.50 17.50 1250 10.8049880-002 20 x 20 19.50 19.50 1390 11.9049880-006 24 x 12 23.38 11.38 1000 8.4049880-015 24 x 18 23.50 17.50 1500 13.0049880-012 24 x 20 23.50 19.50 1670 14.3049880-005 24 x 24 23.38 23.38 2000 17.3049880-010 25 x 14 24.50 13.50 1220 10.4049880-020 25 x 15 24.50 14.50 1300 11.6049880-016 24 x 16 24.50 15.50 1335 11.8049880-004 25 x 16 24.50 15.50 1390 12.4049880-014 25 x 18 24.50 17.50 1565 13.5049880-003 25 x 20 24.50 19.50 1740 14.9049880-018 25 x 25 24.50 24.50 2170 19.0



(inches)

Actual Size(inches) Initial Resistance

(inches w.g.) Airflow Capacity

(cfm)Total Media Area

(sq. ft.)Pleats per

Linear FootDepth Height Width

054862-018

1

10 x 10

0.88

9.50 9.50

0.23

240 1.6


054862-025 12 x 12 11.50 11.50 350 2.5054862-012 16 x 16 15.50 15.50 620 4.3054862-009 20 x 7 19.50 6.50 340 2.4054862-016 20 x 10 19.50 9.50 490 3.3054862-019 20 x 12 19.50 11.50 580 4.1

054862-006 20 x 14 19.50 13.50 680 4.6054862-008 20 x 15 19.50 14.50 730 5.1054862-001 20 x 16 19.50 15.50 780 5.4054862-020 20 x 18 19.50 17.50 880 6.1054862-002 20 x 20 19.50 19.50 970 6.6054862-021 22 x 22 21.50 21.50 1180 8.2054862-022 24 x 10 23.50 9.50 580 4.0054862-010 24 x 12 23.50 11.50 700 4.9054862-015 24 x 16 23.50 15.50 910 6.7054862-028 24 x 18 23.50 17.50 1050 7.3054862-011 24 x 20 23.50 19.50 1170 8.0054862-005 24 x 24 23.50 23.50 1400 9.8054862-023 25 x 10 24.50 9.50 610 4.1054862-024 25 x 12 24.50 11.50 730 5.2054862-007 25 x 14 24.50 13.50 850 5.7054862-013 25 x 15 24.50 14.50 910 6.4

2 Deep Filter (actual fi lter depth 1.75 )


PERFORMANCE DATA (continued) Farr 30/30



32/62



(inches)

Actual Size(inches)

InitialResistance

(inches w.g.)

AirflowCapacity

(cfm)

Total Media Area(sq. ft.)

Pleats perLinear Foot

Depth Height Width059413-004

4

20 x 16

3.75

19.38 15.38

0.27

1100 15.7


059413-003 20 x 20 19.38 19.38 1390 18.9059413-002 24 x 12 23.38 11.38 1000 13.9059413-009 24 x 18 23.38 17.38 1500 20.2059413-008 24 x 20 23.38 19.38 1670 22.7059413-001 24 x 24 23.38 23.38 2000 27.7059413-005 25 x 16 24.38 15.38 1390 19.7059413-006 25 x 20 24.38 19.38 1740 23.6059413-010 25 x 25 24.38 24.38 2170 30.0059413-007 25 x 29 24.38 28.38 2520 35.4


Data notes on previous page.

4 deep 30/30 is available with a headerfor side-access housing installation.

Request Product Sheet 1003.

Available in UL Class One for locationshaving this building code requirement.

Request Product Sheet 1002CL1.

D il d i i f C l F d il bl lf

250 375 500 625

Initial Resistance Versus Air ow

1000 1500 2000 2500Cubic Feet Per Minute (cfm)

Feet Per Minute (fpm)

0.1

0.2

0.3

0.6

0.5

0.4

0.7

0.8

1.0

0.9

R e s i s t a n c e

( i n c h e s , w

. g . )

30/30 2 Deep

30/30 4 Deep

Contact factory beforeoperating above 2000 cfmfor a 1 deep lter and above

2400 cfm for 2 and 4deep lters.

30/30 1 Deep

r e s s u r e

Series2000 Magnehelic Differential Pressure Gages


33/62

P r

Select the Dwyer Magnehelic gage for high accuracy guaranteedwithin 2% of full scale and for the wide choice of 81 models available to suit

your needs precisely. Using Dwyer's simple, fric tionless Magnehel ic gage

movement, it quickly indicates low air or non-corrosive gas pressures eitherpositive, negative (vacuum) or differential. The design resists shock, vibra-tion and over-pressures. No manometer fluid to evaporate, freeze or causetoxic or leveling problems. It's inexpensive, too.The Magnehelic gage is the industry standard to measure fan and blow-er pressures, filter resistance, air velocity, furnace draft, pressure dropacross orifice plates, liquid levels with bubbler systems and pressures influid amplifier or fluidic systems. It also checks gas-air ratio controls and au-tomatic valves, and monitors blood and respiratory pressures in medical careequipment.

Note: M ay be u sed w ith H ydrogen. W hen o rdering a B una-N diaphragmpressures m ust be less than 35 psi.

SPECIFICATIONSService: A ir and no n-com bu stible, com patible gases. (N atural G as op tion avail-able.)Wetted Materials: C onsult fac tory.Housing: D ie cast alum inu m case and beze l, w ith acrylic co ver. Exterior finish isco ated g ray to w ithstand 1 68 hou r salt spray corrosion test.Accuracy: 2 % of full scale (3 % on - 0, -100 P a, -125 P a, 10M M and 4 %on - 00, -60 P a, -6M M rang es), throughou t rang e at 70F (21 .1C ).Pressure Limits: -20 H g. to 15 psig. (-0.67 7 b ar to 1 .03 4 b ar); M P op tion :35 p sig (2.41 b ar), H P option : 80 p sig (5.52 b ar).Overpressure: R elief plug op ens at approxim ately 25 psig (1.72 bar), stand ardgage s only.Temperature Limits: 20 to 14 0F.* (-6.67 to 60 C ).Size: 4 (10 1.6 m m ) D iam eter dial face .Mounting Orientation: D iap hragm in vertical position. C onsult factory forother position orien tations.Process Connections: 1/8 fem ale N P T d up licate high and low pressure tap s- on e pair side and o ne p air back .Weight: 1 lb 2 oz (510 g), M P & H P 2 lb 2 oz (963 g).Standard Accessories: Tw o 1 /8 N P T p lug s for duplicate pressu re tap s, tw o1/8 pipe thread to rub be r tub ing ad ap ter and three flush m ou nting ad ap tersw ith screw s. (M ou nting and snap ring retainer substituted for 3 ad ap ters in M P& H P gag e acce ssories.)*Low tem perature m od els ava ilab le a s special op tion .

Fo r app lication s w ith h igh cyc le rate w ithin g ag e total pressure rating , next high er rating is recom -m end ed. See M edium and H igh p ressure options at low er left.

OPTIONS AND ACCESSORIESMOUNTING.A sing le case

size is used for m ost m od els ofM ag neh elic gag es. They ca nbe flush or surface m ou ntedw ith stan da rd h ardw are sup -plied . W ith the op tiona l A -610P ipe M ounting K it they m ay be conven ien tly installed on horizontal or vertica l 1 14 -2 pipe. Altho ug h ca librated for vertical position, m an y ranges ab ove 1 m ay be u sedat any ang le b y sim ply re-zeroing . H ow ever, for m axim um acc uracy, they m ust becalibrated in the sam e position in w hich they are used . These ch aracteristics m akeM agnehelic gag es idea l for both stationa ry and portab le applica tions. A 4 916 holeis req uired for flush p an el m oun ting . C om plete m oun ting an d co nn ec tion fitting splus instructions are furnished w ith each instrum en t.

Flush ...Surface...or Pipe M ounted

VENT VALVESIn applica tion s w he re p ressu re is co ntinu ou s and the M ag ne -h li i t d b t l l tit b i hi h

2000 MagnehelicDifferential Pressure GagesIndicate Positive, Negative or Differential, Accurate within 2%

11/16[17.46]

1/8 LOWPRESSURE

7/16[11.11]

1-11/16[42.86]

1/2[12.70]

1/8 NPT LOWPRESSURE

1/8 NPT HIGHPRESSURE

1/2[12.70]1/8 NPT HIGHPRESSURE

4-1/8 [104.78] BOLTCIRCLE FOR PANEL MOUNTING

120 APART

1-1/4[31.75]

4-3/4[120.65]

1-3/4[44.45]

Standard M agnehelic Pressure Gage has alarge, easy-to-read 4" dial.

Dimensions, Standard Series 2000 Magnehelic Pressure Gages.(Slightly different on medium and high p ressure models)

Patent Nos. 4,030,3655,012,678

Transparent OverlaysFu rnished in red and green to high ligh t and em ph asizecritica l pressures.

Adjustable Signal FlagIntegral w ith plastic g ag e cover. A vailab le for m ost m od-els exce pt tho se w ith m ed ium or high pressure co n-struction . C an be orde red w ith gag e or sep arate.

LED Setpoint IndicatorB righ t red LE D on righ t of sca le sh ow s w hen se tpoint isreach ed . Field ad justab le from ga ge face, un it op erateson 1 2-24 V D C . R equ ires M P or H P style cover andbezel.

P r e s suQuality design and construction features


34/62

ur e

Quality design and construction features

SERIES 2000 MAGNEHELIC GAGE MODELS AND RANGESThe models below will fulfill most requirements. Page 479 also shows examples of specialmodels built for OEM customers. For special scales furnished in ounces per square inch,inches of mercury, metric units, etc., contact the factory.

MODELS

O-ring seal for co ver assu res pressureintegrity of case .

Blowout plug of silicone rub ber protec tsag ainst overpressure on 15 psig ratedm od els. O pens a t approxim ately 25 psig.

Die cast aluminum case is p rec ision m ad ean d iridite-dipped to w ithstan d 1 68 h our saltsp ray corrosion test. Exterior finish ed inbaked da rk gray ham m erloid. O ne case sizeis used for all stan dard p ressure o ptions, an dfor both su rface and flush m oun ting .

Silicone rubber diaphragm w ith integrallym olded O -ring is sup ported by fron t and rearplates. It is locked and sealed in position w itha sealing plate and retaining ring. D iap hragmm otion is restricted to p revent dam ag e d ue tooverpressures.

Calibrated range sp ring is flat spring stee l.S m all am plitud e o f m otion assuresco nsistency and long life. It rea cts to pressureon diap hragm . Live len gth ad justab le forcalibration.

Samarium Cobalt magnet m ounted at oneen d of ran ge sp ring rotates he lix w itho ut m e-ch an ica l linkag es.

Bezel provides flan ge for flush m oun ting inpan el.

Clear plastic face is highly resistant tobreakage. P rovides u nd istorted view ing ofpointer and sca le.

Precision litho-printed scale is accurateand easy to read .

Red tipped pointer of he at treated alum inu mtubing is easy to see . It is rigidly m ounted onthe h elix shaft.

Pointer stops of m olde d rub be r preventpointer over-travel w itho ut dam ag e.

Wishbone assembly provides m ou nting forhelix, helix b earings and pointer shaft.

J eweled bearings are sho ck-resistant m ounted ;provide virtually friction-free m otion for helix.M otion dam ped w ith high visco sity silico nefluid.

Zero adjustment screw is convenien tlyloca ted in the plastic cover, and is acc essible

w itho ut rem oving co ver. O -ring sea l providespressure tightness.

Helix is p recision m ad e from an alloy of high m ag ne tic p erm eability. M oun ted in jew eledbea rings, it turns free ly, follow ing the m agnetic field to m ove the p ointer across the scale.

ModelNumber

RangeInches

of WaterModel

Number

ModelNumber

2300-023012302230423102320

2330

22012202220322042205

.25-0-.25.5-0-.51-0-12-0-25-0-5

10-0-10

15-0-15Range

PSI

0-10-20-30-40-5

RangeZero

CenterInches of

Water

Dual Scale Air Velocity Units

For use with pitot tube.

Zero Center Ranges

ModelNumber

ModelNumber

Range,CM ofWater

ModelNumber

Range,Pascals

ModelNumber

RangeMM of Water

2000-00AV2000-0AV2001AV2002AV2010AV

0-.25/300-20000-.50/500-28000-1.0/500-40000-2.0/1000-56000-10/2000-12500

Range in W.C.Velocity, F.P.M.

ModelNumber

Range,Kilopascals

2000-6MM2000-10MM2000-25MM2000-50MM2000-80MM

0-60-100-250-500-80

2000-15CM2000-20CM2000-25CM2000-50CM2000-80CM2000-100CM2000-150CM2000-200CM2000-250CM2000-300CM

0-150-200-250-500-800-100

0-1500-2000-2500-300

2300-4CM2300-10CM2300-30CM

2-0-25-0-5

15-0-152000-1KPA2000-1.5KPA

0-10-1.5

Dual Scale English/Metric ModelsModel

Number

2000-OD2001D2002D2003D2004D2006D2008D

2010D

Range,In. W.C.

0-0.50-1.00-2.00-3.00-4.00-6.00-8.0

0-10

Range,Pa or kPa

0-125 Pa0-250 Pa0-500 Pa0-750 Pa0-1.0 kPa0-1.5 kPa0-2.0 kPa

0-2.5 kPa

2000-00N2000-002000-02001200220032004200520062008201020152020202520302040

.05-0-.20-.250-.500-1.00-2.00-3.0

0-4.00-5.00-6.00-8.00-100-150-200-250-300 40

Zero Center Ranges

2300-60PA2300-100PA2300-120PA2300-250PA

2300-500PA

30-0-3050-0-5060-0-60125-0-125

250-0-250


35/62

Extruded aluminum(6063T5) damper frame is not less than .080" (2.03mm) in thickness. Damper frame is 4" deep.

Blades are extruded aluminum (6063T5) proles.

Blade seals are extruded EPDM. Frame seals are extruded silicone. Seals are secured in an integral slot within thealuminum extrusions.

Bearings are composed of a Celcon inner bearing xed to a7 / 16"(11.11mm) aluminum hexagon blade pin, rotating within a polycarbonate outer bearing inserted in the frame, resulting in no metal-to-metal or metal-to-plastic contact.

Linkage hardware is installed in the frame side and constructed of aluminum and corrosion-resistant, zinc-plated steel,complete with cup-point trunnion screws for a slip-proof grip.

Dampers are designed for operation in temperatures ranging between -40F(-40C) and 212F(100C).

Leakage does not exceed 3 cfm/ft. (15.2 l/s/m2) against 1 (.25 kPa) w.g. differential static pressure.

Dampers are available with either opposed blade action or parallel blade action.

Dampers are made to size required without blanking off free area.

Dampers are available in two mounting types: i.e., "Installed in Duct" or "Flanged to Duct".

Installation of dampers must be in accordance with current manufacturers installation guidelines provided with eachshipment of TAMCO dampers. (Note that all technical information available on TAMCOs web site at www.tamco.casupersedes and takes precedence over all information contained within the printed catalog.)

Intermediate or tubular steel structural support is required to resist applied pressure loads for dampers that consist oftwo or more sections in both height and width. (See TAMCO Aluminum Damper Installation Guidelines.)

S E R I E S 1 0 0 0 AIR-FOIL CONTROL DAMPER

4000 SERIESMULLION TYPE

CHANNELFRAME

3000 SERIESMULLION TYPE

EXTERIORFLANGE

OPPOSED

ACTION

PARALLELACTION

"FLANGED TO DUCT" TYPE2" added to duct width & height dimensions

"INSTALLED IN DUCT" TYPE" deducted for clearance from width & height dimensions unless otherwise specified

SPECIFICATIONS


36/62

S E R I E S 1 0 0 0 AIR-FOIL CONTROL DAMPERS

1.00.90.80.70.60.50.4

0.3

0.2

0.1

0.08

0.060.050.04

0.03P r

e s s u r e

D r o p

( i n c h e s w . g . )

( i n t a

k e m o d e )

VELOCITY VS. PRESSURE DROP

48" x 12" (1219mm x 305mm)

12" x 12" (305mm x 305mm)

12" x 48" (305mm x 1219mm) 24" x 24" (610mm x 610mm)

36" x 36"

(914mm x 914mm)

60"

48"

36"

24"

12"3 4 5 6 7 8 9 10 11 12 13 14 15

B l a d e

L e n g

t h ( i n c

h e s )

Maximum Design Total Static Pressure (inches w.g.)

BLADE DESIGN PRESSURE LIMITATIONSM A X . B L A D E L E N G T H v s . M A X . D E S I G

N V E L O C I T Y ( f p m )

Leakage testing was conducted in accordance with AMCA Standard 500-D-98. Holding torqueapplied was 5.2 in.-lbs./sq. ft. on opposed blade dampers and 7 in.-lbs./sq. ft. on parallelblade dampers AMCA Standard 500-D-98 states that air leakage is based on operation

between 50F(10C)and 104F(40C).All tests were performed with 120 in.-lbs. in resultingin a maximum of 120 in.-lbs./ft with the 12 x 12 damper.The following sizes of TAMCO Series 1000 dampers were tested: 12" x 12"(305 mm x 305 mm), 24" x 24"(610 mm x 610 mm),48" x 12"(1219 mm x 305 mm)12" x 48" (305 mm x 1219 mm),36" x 36" (914 mm x 914 mm),60" x 36" (1524 mm x 914 mm).

Pressure

Class

LEAKAGE, ft3 /min/ft 2 (l/s/m 2)

Required Rating Extended Ranges (Opt.) 1" / 0.25 kPa 4" / 1.0 kPa 8" / 2.0 kPa 12" / 3.0 kPa

1A 3 / 15.2 n/a n/a n/a1 4 / 20.3 8 / 40.6 11 / 55.9 14 / 71.12 10 / 50.8 20 / 102 28 / 142 35 / 1783 40 / 203 80 / 406 112 / 569 140 / 711

1 in. w.g. 4 in. w.g. 8 in. w.g.Damper Width

12" (305mm) 1A 1 1124" (610mm) 1A 1 1136" (914mm) 1A 1 n/a48" (1219mm) 1A 1 n/a60" (1524mm) 1A 1 n/a

PERFORMANCE DATA

TAMCO LEAKAGE RATING

LEAKAGE CLASS DEFINITIONS

OEM Insulations

E i S i Gl B d


37/62

DescriptionEquipment Spin-Glas Board is a rigid board manufactured fromfine, rotary-process glass fibers bonded with a special thermosetting resin.

Thermal and Acoustical Solution. Equipment Spin-Glas Boardcan be used in a variety of applications that require good thermal and acoustical efficiency in a minimal space.

Appliance and Equipment Applications. Because the glass

fibers in Equipment Spin-Glas Board are extremely fine, theycreate an enormous number of minute air spaces, making theinsulation highly effective for sound absorption and thermalproperties.

These glass fibers are resistant to the effects of moisture, oil,grease, and most acids. Because these fibers are highly resilient, they resist settling, breakdown or sagging from vibration. Theyyield readily to impact and protect facings from puncture or tearing.

Equipment Spin-Glas Board provides neat, square corners for animproved, finished appearance for equipment systems.

The inherent physical properties of Equipment Spin-Glas Boardassure ease of application. It can be readily cut with a knife andsecured with mechanical fasteners or adhesives.

Available Forms. See Equipment Spin-Glas Board PurchaseGuide, ESG-IS-210 for specific details.

Custom Fabrications. A Johns Manville Approved Fabricator

can develop and apply facings for airstream applications aswell as fabricate Equipment Spin-Glas Board to meet yourspecific service conditions and performance requirements.

Applications Office Partitions Ceiling Panels Wall Panels HVAC Equipment

Insulation Properties Excellent Thermal Efficiency Excellent Acoustical Performance Easy to Fabricate Easy to Handle and Install

SpecificationsTemperature Limit: 350F (177C) (unfaced). Faced surfaceshould not exceed 150F (83C).

Fire Hazard Classification: 25/50 Flame Spread/SmokeDeveloped Ratings (per ASTM E 84, UL 723, and CAN/ULCS102-M88). Labels supplied when requested on order.Meets NFPA 90A and 90B.

Facings: FSK (foil/scrim/kraft)Coating: Black Acrylic Coating (maximum rated air velocity is5,000 fpm) (1,500 mpm)

Fabricated Products: Johns Manville Equipment Spin-GlasBoard is manufactured to specific customer widthrequirements. Contact your Johns Manville salesrepresentative for limitations. Die-cut or fabricated pieces aregenerally supplied by one of the strategically located JohnsManville fabricators who are specially equipped to provideprompt service to manufacturers in their area.

General PropertiesMoisture Absorption: Less than 1.0% by volumeAlkalinity: Less than 6.0% expressed

as Na 2OC i it (With t l

Equipment Spin-Glas BoardEquipment Insulation

Equipment Spin-Glas Board


38/62

q p pEquipment Insulation

Acoustical Performance

Sound Absorption Coefficients*Type A MountingDensity Thickness Frequency (Hz)pcf kg/m3 in mm 125 250 500 1000 2000 4000 NRC**3.00 48.1 1 25 0.06 0.26 0.61 0.86 0.99 1.03 0.703.00 48.1 2 51 0.17 0.80 1.16 1.15 1.11 1.10 1.054.25 68.1 1 25 0.03 0.32 0.80 1.04 1.05 1.05 0.804.25 68.1 2 51 0.27 0.91 1.11 1.09 1.09 1.09 1.056.00 96.2 1 25 0.10 0.35 0.85 1.04 1.05 1.03 0.806.00 96.2 2 51 0.38 0.93 1.10 1.07 1.07 1.07 1.05* Tested in accordance with ASTM C 423-90a and ASTM E 795-83** Noise Reduction Coefficient

Insulation Systems, OEM InsulationsFor Order Placement For Technical Information

(800) 458-7198Eastern Region(Defiance, OH)P.O. Box 158Defiance, OH 43512(800) 426-2435Fax: (800) 329-7397

Western Region(Littleton, CO)P.O. Box 625005Littleton, CO 80162(800) 293-3393Fax: (800) 741-0183

Thermal Conductivity (k)Density Mean Temp. @ 75F (24C)pcf kg/m3 Btuin/(hrft2F) W/mK3.00 48.1 .254 .0354.25 68.1 .23 .0336.00 96.2 .23 .033


39/62

Technical Product DataThe Chemical Company

U r e t h a n e p e c i a l t i e s

AUTOFROTH 98-B-0411 RESIN/ AUTOFROTH 9300A ISOCYANATERIGID POLYURETHANE FOAM SYSTEM

DESCRIPTIONAutofroth 98-B-0411 Resin/ Autofroth 9300A Isocyanate is a two- componentpolymeric MDI based system utilizing water and HFC134a and HFC245fa as

blowing agents. This system is designed for insulation of discontinuous metal-faced sandwich panels.

AUTOFROTH 98-B-0411 RESIN COMPONENTAppearanceOdorDensity, @770FViscosity, @770F

Flash Point, ASTM 3278-89

Amber liquidSlight Amine10 6 lbs /gal

400 cps>200oF

AUTOFROTH 9300A ISOCYANATE COMPONENTAppearanceOdorDensity, @770FViscosity, @774000F0.00016 mm Hg

TYPICAL PROCESSING PARAMETERS

Rai oby wegh (A/ B) 100/ 985Compo ne n Tempe r a ur e 0F 80

ModTemper a ur e 0F100- 105

Nominal Reactivity (sec.)Sr i ngG Tme 100Tac k Tm 145

FeeRseDenst y (pcf ) 190


40/62

Technical Product DataThe Chemical Company

U r e t h a n e p e c i a l U e s

AUTOFROTH 98-B-0411 RESIN/ AUTOFROTH 9300A ISOCYANATERIGID POLYURETHANE FOAM SYSTEM

TYPICAL PHYSICAL PROPERTIES

Molded Panel, pcfCore Density, pcf

Compressive Strength, psi@10% deflectionParallelPerpendicular

K-Factor, Initial (BTU-in/hr-ft2-0F|

UL Subject 723 (File #R5692-6 Core Panels)/ASTM E-84:Flame Spread1Smoke DensityMinimum Self-Ignition Temperature

2.602.40

2820

0.145

2030 04000C (7520F)

Dimensional Stability^ % Volume Change

-20oF (7 Days)

100oF/100 RH (28 Days)

1580F (28 Days)

200oF (28 Days)

0

1

1

2

1 This numerical flame spread rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions.


41/62

'BSF Technical Product DataThe Chemical Company

U r e t h a n e p e c i a l t i e s

AUTOFROTH 98-B-0411 RESIN/ AUTOFROTH 9300A ISOCYANATERIGID URETHANE FOAM SYSTEM

AF 0411 K-Factor Curve

Mean Temp, F

AF 0411 R-Value Curve

Mean Temp, F


42/62

ACH550 Product Overview


43/62

DescriptionThe ACH550 series is a microprocessor based Pulse Width Modulated (PWM) adjustable speed ACdrive. The ACH550 drive takes advantage of sophisticated microprocessor control and advanced IGBT

power switching technology to deliver high-performance control of AC motors for a wide range of HVACapplications.

With drives ranging from 1 to 550 HP, the ACH550 series features a universal full graphic interface thatspeaks to the operator in plain English phrases, greatly simplifying set-up, operation, and faultdiagnosis. The ACH550 is also programmable in fourteen other languages.

Each ACH550 drive comes equipped with an extensive library of pre-programmed HVAC applicationmacros which, at a touch of a button, allow rapid configuration of inputs, outputs, and performanceparameters for specific HVAC applications to maximize convenience and minimize start-up time. The

ACH550 series can handle the most demanding commercial applications in an efficient, dependable, andeconomic manner.

ACH550 Standard Features UL, cUL labeled and CE markedEMI/RFI Fil (1 st E i R i d Di ib i )

HVAC Specific Application MacrosS t S f ti (2) d R P i i I t


44/62

EMI/RFI Filter (1 st Environment, Restricted Distribution)Start-Up AssistantsMaintenance AssistantsDiagnostic AssistantsReal Time Clock

Includes Day, Date and TimeOperator Panel Parameter Backup (read/write)Full Graphic and Multilingual Display

for Operator Control, Parameter Set-Up andOperating

Data Display:Output Frequency (Hz)Speed (RPM)Motor CurrentCalculated % Motor TorqueCalculated Motor Power (kW)DC Bus Voltage

Output VoltageHeatsink TemperatureElapsed Time Meter (reset-able)KWh (reset-able)Input / Output Terminal MonitorPID Actual Value (Feedback) & ErrorFault TextWarning TextThree (3) Scalable Process Variable DisplaysUser Definable Engineering Units

Two (2) Programmable Analog InputsSix (6) Programmable Digital Inputs

Two (2) Programmable Analog OutputsUp to six (6) Programmable Relay Outputs (Three (3)Standard)

Adjustable Filters on Analog Inputs and OutputsMathematical Functions on Analog Reference Signals

All Control Inputs Isolated from Ground and PowerFour (4) Resident Serial Communication Protocols

Johnson Controls N2Siemens Building Technologies FLN (P1)Modbus RTUBACnet (MS/TP)

Input Speed SignalsCurrent 0 (4) to 20 mAVoltage 0 (2) to 10 VDCIncrease/Decrease Reference Contacts(Floating Point)Serial Communications

Start/Stop2 Wire (Dry Contact Closure)3 Wire (Momentary Contact)

Application of Input Power Application of Reference Signal (PID Sleep/Wake-

Up)Serial Communications

Start FunctionsRampFlying StartPremagnetization on Start

Automatic Torque Boost Automatic Torque Boost with Flying Start Auto Restart (Reset) Customer Selectable and

Separate Safeties (2) and Run Permissive InputsDamper ControlOverride Input (Fire Mode)Timer Functions

Four (4) Daily Start/Stop Time PeriodsFour (4) Weekly Start/Stop Time PeriodsFour Timers for Collecting Time Periods and

OverridesSeven (7) Preset SpeedsSupervision Functions

Adjustable Current LimitElectronic Reverse

Automatic Extended Power Loss Ride Through(Selectable)Programmable Maximum Frequency to 500 HzPID Control

Two (2) Integral Independent Programmable PID

Setpoint Controllers (Process and External)External Selection between Two (2) Sets ofProcess

PID Controller ParametersPID Sleep/Wake-Up

Motor Control FeaturesScalar (V/Hz) and Vector Modes of Motor ControlV/Hz Shapes

LinearSquared

Energy OptimizationIR Compensation

Slip CompensationThree (3) Critical Frequency Lockout BandsPreprogrammed Protection Circuits

OvercurrentShort CircuitGround FaultOvervoltageUndervoltage

Input Phase LossOutput Device (IGBT) Overtemperature

Adjustable Current Limit RegulatorUL508C approved Electronic Motor Overload (I 2T)

Programmable Fault Functions for Protection IncludeLoss of Analog InputPanel LossExternal FaultMotor Thermal ProtectionStallUnderloadMotor Phase LossGround Fault

5% Input ImpedanceEquivalent 5% Impedance with Internal Reactor(s)Patented Swinging Choke Design for Superior

Harmonic Mitigation (R1 to R4)

OPTIONAL FEATURES3 Relay Extension Module (OREL-01)115/230 V Digital input Interface Card (OHDI-01)Fieldbus Adapter Modules

ACH550 Specifications


45/62

Input ConnectionInput Voltage (U 1).................................................................... 208/220/230/240 VAC 3-phase +/-10%

208/220/230/240 VAC 1-phase +/-10%380/400/415/440/460/480 VAC 3-phase +/-10%500/600 VAC 3-phase +/-10%

Frequency: .............................................................................48 - 63 HzLine Limitations: ..................................................................... Max +/-3% of nominal phase to phase input voltageFundamental Power Factor (cos ): ..................................... 0.98 at nominal loadConnection: ............................................................................U 1, V1, W 1 (U1, V1, 1-phase)Output (Motor) ConnectionOutput Voltage: ...................................................................... 0 to U 1, 3-phase symmetrical, U 2 at the field weakening pointOutput Frequency: ................................................................. -500 to 500 HzFrequency Resolution: ........................................................... 0.01 HzContinuous Output Current:

Variable Torque: .................................................... 1.0 * I 2N (Nominal rated output current, Variable Torque)Short Term Overload Capacity:

Variable Torque: ..................................................... 1.1 * I 2N , (1 min/10 min)Peak Overload Capacity:

Variable Torque: ..................................................... 1.35 * I 2N , (2 sec/1 min)Base Motor Frequency Range: ...............................................10 to 500 HzSwitching Frequency: ............................................................. 1, 4, 8 or 12 kHz

Acceleration Time: ................................................................. 0.1 to 1800 sDeceleration Time: ................................................................. 0.1 to 1800 sEfficiency: ............................................................................... 0.98 at nominal power levelShort Circuit Withstand Rating: .............................................. 100,000 AIC (UL) w/o fusesConnection: ............................................................................U 2, V2, W 2 EnclosureStyle: ....................................................................................... UL (NEMA) Type 1, Type 12, or Type 3R

UL Plenum Rated Type 1, Type 12 Agency ApprovalListing and Compliance:.......................................................... UL, cUL, CEAmbient Conditions, Operation

Air Temperature: ..................................................................... 0 0 to 40 0C (32 0 to 104 0F), above 40 0C the maximum output current isde-rated 1% for every additional 1 0C (up to 50 0C (122 0F)) maximumlimit.

Relative Humidity: ................................................................... 5 to 95%, no condensation allowed, maximum relative humidity is 60%in the presence of corrosive gasses

Contamination Levels:IEC:......................................................................... 60721-3-1, 60721-3-2 and 60721-3-3Chemical Gasses:................................................... 3C1 and 3C2Solid Particles:........................................................ 3S2

Installation Site Altitude:..........................................................0 to 1000 m (3300 ft) above sea level. At sites over 1000 m (3300 ft)above sea level, the maximum power is de-rated 1% for everyadditional 100 m (330 ft). If the installation site is higher than 2000 m(6600 ft) above sea level, please contact your local ABB distributor orrepresentative for further information

Vibration:................................................................................. Max 3.0 mm (0.12 in) 2 to 9 Hz, Max 10 m/s 2 (33 ft/s 2) 9 to 200 Hzsinusoidal

Ambient Conditions, Storage (in Protective Shipping Package) Air Temperature:......................................................................-40 0 to 70 0C (-40 0 to 158 0F) Relative Humidity:....................................................................Less than 95%, no condensation allowed

Vibration Tested to (IEC 60068-2-6):........................................In accordance with ISTA 1A and 1B specifications Bump Tested to (IEC 60068-2-29):..........................................Max 100 m/s 2 (330 ft/s 2) 11 ms (Tested 500 times each axis,each pole; 3000 times total)

Ambient Conditions, Transportation (in Protective Shipping Package) Air Temperature:....................................................................... -40 0 to 70 0C (-40 0 to 158 0F) Relative Humidity:....................................................................Less than 95%, no condensation allowed

Atmospheric Pressure:.............................................................60 to 106 kPa (8.7 to 15.4 PSI) 2 f 2

ACH550 Specifications (continued)


46/62

Cooling InformationCooling Method:...................................................................... Integral fan(s)Power Loss: ...........................................................................Approximately 3% of rated powerAnalog InputsQuantity...................................................................................Two (2) programmableVoltage Reference: ................................................................. 0 (2) to 10 V, 250kOhm, single endedCurrent Reference:.................................................................. 0 (4) to 20 mA, 100Ohm, single endedPotentiometer:......................................................................... 10 VDC, 10 mA (1K to 10KOhms)Input Updating Time................................................................ 8 msTerminal Block Size ................................................................ 2.3mm 2 / 14AWGReference Power SupplyReference Voltage ..................................................................+10 VDC, 1% at 25 0C (77 0F)Maximum Load ....................................................................... 10 mA

Applicable Potentiometer ........................................................ 1 kOhm to 10 kOhmTerminal Block Size ................................................................ 2.3mm 2 / 14AWGAnalog OutputsQuantity...................................................................................Two (2) programmable current outputsSignal Level ............................................................................0 (4) to 20 mA

Accuracy ................................................................................. +/- 1% full scale range at 25 0C (77 0F)Maximum Load Impedance..................................................... 500 OhmsOutput Updating Time............................................................. 2 msTerminal Block Size ................................................................ 2.3mm 2 / 14AWGDigital InputsQuantity................................................................................... Six (6) programmable digital inputsIsolation................................................................................... Isolated as one groupSignal Level ............................................................................ 24 VDC, (10V Logic 0)Input Current ........................................................................... 15 mA at 24 VDC

Input Updating Time:............................................................... 4 msTerminal Block Size ................................................................ 2.3mm 2 / 14AWGInternal Power SupplyPrimary Use ............................................................................ Internal supply for digital inputsVoltage:................................................................................... +24 VDC, max 250 mAMaximum Current:................................................................... 250 mAProtection:...............................................................................Short circuit protectedRelay OutputsQuantity...................................................................................Three (3) programmable relay (Form C) outputsSwitching Capacity:................................................................. 8 A at 24 VDC or 250 VAC, 0.4 A at 120 VDCMax Continuous Current: ........................................................ 2A RMS

Contact Material:..................................................................... Silver Cadmium Oxide (AgCdO)Isolation Test Voltage ............................................................. 4 kVAC, 1 minuteOutput Updating Time............................................................. 12 msTerminal Block Size ................................................................ 2.3mm 2 / 14AWGProtectionsSingle Phase........................................................................... Protected (input & output)Overcurrent Trip Limit: ............................................................ 3.5 x I 2N instantaneous

Adjustable Current Regulation Limit: ...................................... 1.1 x I 2N (RMS) max.Overvoltage Trip Limit:............................................................ 1.30 x U NUndervoltage Trip Limit:.......................................................... 0.65 x U NOvertemperature (Heatsink):................................................... +115C (+239F)

Auxiliary Voltage: .................................................................... Short Circuit ProtectedGround Fault: .......................................................................... ProtectedShort Circuit: ........................................................................... ProtectedMicroprocessor fault:............................................................... ProtectedMotor Stall Protection:............................................................. ProtectedMotor Overtemperature Protection (I 2t):.................................. ProtectedInput Power Loss of Phase: .................................................... ProtectedLoss of Reference:.................................................................. Protected

ACH550 Control Panel


47/62

The ACH550 Control Panel is a multifunction control panel with full graphic LCD display and multiplelanguage capability. The control panel can be connected to and detached from the ACH550 at any time.The panel can be used to upload and copy parameters to other ACH550 drives.

Run Indication and Shaft DirectionControl Panel Display Significance

Rotating arrow (clockwise or counterclockwise) Drive is running and at set point

Shaft direction is forward or reverseRotating arrow blinking Drive is operating but not at setpoint

Stationary arrow Drive is stopped

LED IndicatorsThe green LED indicates that the power is on and the drive is operating normally. The red LED indicatesa fault. A blinking green LED indicates an alarm condition. A blinking red LED indicates a fault thatrequires power to be cycled off and on to reset the drive.

Fault IndicationsThe ACH550 Control Panel can display over 20 alarm and fault messages. The last fault and previousfaults (1 to 9) are retained in memory. The last fault and previous faults (1 & 2) also record importantdiagnostic information to assist in troubleshooting. Most faults can be reset by pressing the RESET key(Soft Key 1).

Parameters Application specific parameters are immediately accessible through a selection of start-up Assistants. Acomplete list of parameters is also available grouped by function in approximately 33 menu groups. One

of the basic menu functions can be used to display the complete list of changed parameters.Real Time ClockThe Operator Control Panel includes a real time clock which provides Day, Date and Time information,displayed in a choice of formats. The real time clock has a 10 year battery back up and provides time anddate stamping of drive faults and other events. The clock is also used by the ACH550s internal timerf i idi i l i l k f / l ll

Control ModesWh h HAND k i d h d i d i h UP/DOWN k dif h


48/62

When the HAND key is pressed, the drive starts and pressing the UP/DOWN keys can modify thereference frequency. The HAND (keypad) control mode is indicated.

When the OFF key is pressed, the drive stops and the OFF control mode is indicated.

When the AUTO key is pressed, the AUTO control mode is indicated. The drive can be started andstopped using whichever remote start/stop command has been configured, a contact closure applied tothe start/stop input, a serial communication command or a process feedback signal. In AUTO mode thedrive speed is typically controlled by the external speed reference input or by the PID controller.

If the HAND key is pressed while the drive is running in the AUTO control mode, the drive continues torun without changing speed, but ceases to respond to external input or PID speed reference changes.(Bumpless transfer) Pressing the UP/DOWN keys can modify the reference frequency.

If the AUTO key is pressed while the drive is running in the HAND control mode and an external startcommand is present, the drive continues to run and follows the acceleration or deceleration control rampto the speed set by the external input or PID speed reference. (Bumpless transfer)

Cable ConnectionsTerminal Description Note

U1, V1, W1 3~ power supply input Use of 1~ supply requires 50% derate of output currentand is applicable for 208 to 240 VAC operation only.

PE / GND Protective Ground Follow local rules for cable size.U2, V2, W2 Power output to motorUc+, Uc- DC busX1 1 to 18 Control Wiring Low voltage control Use shielded cableX1 19 to 27 Control Wiring Low voltage or 115VACX1 28 to 32 Serial Communications Use shielded cable

Follow local codes for cable size. To avoid electromagnetic interference, use separate metallic conduitsfor input power wiring, motor wiring, control and communications wiring. Keep these four classes of wiringseparated in situations where the wiring is not enclosed in metallic conduit. Also, keep 115VAC controlwiring separated from low voltage control wiring and power wiring.

Use shielded cable for control wiring.

Ampacity is based on the use of 60 C rated power cable up to 100 Amps (75 C over 100 Amps).

Refer to the included tables for current ratings, fuse recommendations and maximum wire size capacitiesand tightening torques for the terminals. The ACH550 is suitable for use on a circuit capable of deliveringnot more than 100,000 RMS symmetrical amperes, 480 V maximum. The ACH550 has an electronic

motor protection feature that complies with the requirements of the National Electric Code (NEC). Whenthis feature is selected and properly adjusted. Additional overload protection is not required unless morethan one motor is connected to the drive or unless additional protection is required by applicable safetyregulations.

For CE installation requirements, see ABB publication CE-US-02 CE Council Directives and Variable


49/62


50/62


51/62


52/62

54 5/12


53/62

56 5/12

FOAM


54/62

57 5/12


55/62

58 5/12


56/62

60 5/12


57/62

65 5/12


58/62

UNIT LENGTH + 1 9/16" OVENHANG EAC H SIDE


59/62

UNIT LENGTH

UNIT HEIGHT + 4"ON THE CENTER

HIGHEST SIDE

UNIT WIDTH

UNIT WIDTH + 1 11/16" OVERHANG EAC H SIDE

UNIT HEIGHT+ 1 3/4" ON THE SIDES

DATE

NOVEMBER 2012 DOUBLE SLOPE ROOF DETAIL

MATERIAL

FINISH

SEE CUT SHEET

PERMISSION OF TEAM AIRINC IS PROHIBITED.

DIMENSIONS ARE IN INCHES

-DO NO T SCALE DRAWING

OMAR M.1/8"DRAWN BY:

PROPRIETARY AND CONFIDENTIAL J OB NAME:

DWD UNIT ROOF DETAILFRACTIONAL TOLERANCES:

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OF

TEAMAIRINC. ANY REPRODUCTION IN PARTOR AS A WHOLE WITHOUT THE WRITTEN DRAWING DESCRIPTION

B

DETAIL BSCALE 1 : 3.7


60/62


61/62

66 5/12


62/62

67 5/12

team submittalcustom ahu

Documents