tds20.23.1 [page 1 of 1] technical data sheet sheets/accessories... · 2021. 7. 13. · bs en iso...
TRANSCRIPT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.23.1MCAMP Wall bracket/ACC mounting plate
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
2mm thick material
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCAMP - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCAMP
Product DescriptionWall bracket/ACC mounting plate
Product Dimensions88 x 52 x 15mm
Material Specification:(if applicable)
Utilisation:Bracket used for securing steel wire cable trays to walls and mounting accessory boxes
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
Not suitable for 30mm thick trays
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.26.1MCB35 Bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
0.8mm thick material
Punched from sheet-steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCB35 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCB35
Product DescriptionBracket for MC3050 and MC5550
Product Dimensions37 x 35 x 30 mm
Material Specification:(if applicable)
Utilisation:Hold down L bracket for MC3050 and MC5550
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.1.1MCCA Nut bolt and clamp assembly
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCA - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Codes:MCCA
Product Description:Nut, bolt and clamp assembly
Product Dimensions:30 x 20 mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCCAGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Coupling steel wire cable trays, creating small/large radius bends, right angle bends, radius tee-junctionand crossovers
MCCAGT
21 mm bolt
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.2.1MCCB Nut bolt clamp assembly
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Codes:MCCB
Product Description:Nut, bolt and clamp assembly
Product Dimensions:23.5 x 20 x 21.5 mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCCBGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Creating large radius bends as well as radius/right angle tee-junctions and crossovers
MCCBGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.43.1MCCB100 Cantilever bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCB100
Product DescriptionCantilever bracket for 100mm wide steel wire cable trays
Product Dimensions117 x 92 x 43 mm
Material Specification:(if applicable)
Utilisation:Wall mounted cantilever bracket allowing for steel wire cable tray to be secured through a mechanical connection using the MCCB assembly
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
Oblong holes at 50 mm spacing
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.43.1MCCB150 Cantilever bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCB150
Product DescriptionCantilever bracket for 150 mm wide steel wire cable trays
Product Dimensions157 x 92 x 43 mm
Material Specification:(if applicable)
Utilisation:Wall mounted cantilever bracket allowing for steel wire cable tray to be secured through a mechanical connection using the MCCB assembly
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
Oblong holes at 50 mm spacing
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.43.1MCCB200 Cantilever bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537BS EN ISO 10244
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB200 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCB200
Product DescriptionCantilever bracket for 200 mm wide steel wire cable trays
Product Dimensions217 x 92 x 43 mm
Material Specification:(if applicable)
Utilisation:Wall mounted cantilever bracket allowing for steel wire cable tray to be secured through a mechanical connection using the MCCB assembly
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
Oblong holes at 50 mm spacing
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.43.1MCCB300 Cantilever bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB300 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCB300
Product DescriptionCantilever bracket for 300 mm wide steel wire cable trays
Product Dimensions317 x 92 x 43 mm
Material Specification:(if applicable)
Utilisation:Wall mounted cantilever bracket allowing for steel wire cable tray to be secured through a mechanical connection using the MCCB assembly
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
Oblong holes at 50 mm spacing
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.43.1MCCB400 Cantilever bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCB400 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCB400
Product DescriptionCantilever bracket for 400 mm wide steel wire cable trays
Product Dimensions417 x 157 x 43 mm
Material Specification:(if applicable)
Utilisation:Wall mounted cantilever bracket allowing for steel wire cable tray to be secured through a mechanical connection using the MCCB assembly
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
Oblong holes at 50 mm spacing
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.42.1MCCFB100 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCFB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCFB100
Product DescriptionFast fix ceiling bracket for 100mm widesteel wire cable trays
Product Dimensions171.5 x 215 x 64.5 mm
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.42.1MCCFB150 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
Product CodeMCCFB150
Product Description
Product Dimensions221.5 x 215 x 58 mm
Applicable Standards:
Product Specification:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
Fast fix ceiling bracket for 150mm widesteel wire cable trays
1.5 mm material thickness
Finishes:MCCFB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
The above are typical test results and do not constitute any part of a specification
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.42.1MCCFB200 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
Product CodeMCCFB200
Product Description
Product Dimensions
272 x 215 x 64.5 mm
Applicable Standards:
Product Specification:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
Fast fix ceiling bracket for 200mm widesteel wire cable trays
1.5 mm material thickness
Finishes:MCCFB200 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
The above are typical test results and do not constitute any part of a specification
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.42.1MCCFB300 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
Product CodeMCCFB300
Product Description
Product Dimensions371.5 x 215 x 64.5 mm
Applicable Standards:
Product Specification:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
Fast fix ceiling bracket for 300mm widesteel wire cable trays
1.5 mm material thickness
Finishes:MCCFB300 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
The above are typical test results and do not constitute any part of a specification
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Technical Data Sheet
TDS20.42.1MCCFB400 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
Product CodeMCCFB400
Product Description
Product Dimensions471.5 x 215 x 64.5 mm
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
Fast fix ceiling bracket for 400mm widesteel wire cable trays
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Finishes:MCCFB400 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
The above are typical test results and do not constitute any part of a specification
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.42.1MCCFB450 Fast fix ceiling bracket
Issue Date: 07/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCCFB450 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCFB450
Product Description
Product Dimensions471.5 x 215 x 64.5 mm
Utilisation:Suspending steel wire cable tray from ceilings without the need for any clamping
Fast fix ceiling bracket for 450mm widesteel wire cable trays
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.13.1MCCL Clamp large
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCL - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Codes:MCCL
Product Description:Large hold down clamp
Product Dimensions:59.50 x 37 x 2 mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCCLGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Attaching steel wire cable trays to solid surfaces and strut
MCCLGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.40.1MCCL25 Clamp large
Issue Date: 08/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCL25 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Codes:MCCL25
Product Description:Large hold down clamp
Product Dimensions:35.5 x 35 x 2 mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
Utilisation:Attaching steel wire cable trays to solid surfaces and strut
To fit MCG6060 only
tel: +44 (0) 1248 725 772 fax: +44 (0) 01248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.4.1MCCM Clamp medium
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCM - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Codes:MCCM
Product Description:Medium clamp
Product Dimensions:30 x 20 x 2mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCCMGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Constituent part of both MCCA and MCCB
MCCMGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.3.1MCCS Clamp small Issue Date: 06/2017
[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steel.Manufactured:
The above are typical test results and do not constitute any part of a specification
MCCS - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Codes:MCCS
Product Description:Small clamp
Product Dimensions:23.50 x 20 x 2mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCCSGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Constituent part of MCCA
MCCSGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB100 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB100
Product Description
Product Dimensions200 x 57.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Fast fix channel support bracket for 100mm wide steel wire cable trays
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB150 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB150
Product Description
Product Dimensions250 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Fast fix channel support bracket for 150mm wide steel wire cable trays
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB200 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB200 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB200
Product Description
Product Dimensions300 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Fast fix channel support bracket for 200mm wide steel wire cable trays
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB300 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB300 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB300
Product Dimensions400 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
Product DescriptionFast fix channel support bracket for 300 mm wide steel wire cable trays (suitable for use with multiple smaller trays in various configurations)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB400 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB400 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB400
Product Dimensions500 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
Product DescriptionFast fix channel support bracket for 400 mm wide steel wire cable trays (suitable for use with multiple smaller trays in various configurations)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB450 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB450 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB450
Product Dimensions550 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
Product DescriptionFast fix channel support bracket for 450 mm wide steel wire cable trays (suitable for use with multiple smaller trays in various configurations)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB500 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB500 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB500
Product Dimensions600 x 60.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
Product DescriptionFast fix channel support bracket for 500 mm wide steel wire cable trays (suitable for use with multiple smaller trays in various configurations)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB600 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB600 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB600
Product Dimensions700 x 61.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
Product DescriptionFast fix channel support bracket for 600 mm wide steel wire cable trays (suitable for use with multiple smaller trays in various configurations)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.39.1MCCSB1000 Fast fix support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCCSB1000 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCCSB1000
Product Description
Product Dimensions1020 x 61.5 x 23.5 mm
Material Specification:(if applicable)
Utilisation:Suspending steel wire cable tray from walls or securing to flooring without the need for a mechanical connection
Fast fix channel support bracket, suitable for use withmultiple steel wire cable trays in various configurations
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.5 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.35.1MCD Steel wire cable tray divider
Issue Date: 07/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCD30 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Code:MCD30
Product Description:Steel wire cable tray divider for 30 mm trays
Product Dimensions:MCD30 - 3000 x 24 x 1 mm
Material Specification:(if applicable)
Utilisation:Mounted within a steel wire cable tray to divide the tray into multiple compartments. Availiable for 30, 55 and 106mm high trays
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
MCD55MCD106
MCD55 - 3000 x 49 x 1 mmMCD106 - 3000 x 100 x 1 mm
3000
A
A
30
R10
1226
R7
1226
350
100
100
200
100
100
200
9610
2
C
DETAIL A SCALE 1 : 5
7
2212
7.208.20
13.2015.2020.2021.20
2526
R7
R6
DETAIL C SCALE 1 : 2
HOLE PATTERNS OF OBROUND SLOTSAND TABS ARE COPIED THROUGHOUTTHE 3 METER LENGTH OF THE PRODUCT.
DIVIDER SIZEMCD30 A = 24MMMCD55 A = 49MMMCD75 A = 74MM
MCD106 A = 100MM
CABLE TRAY DIVIDER
ADO NOT SCALE DRAWING
MA.01.02.0092SHEET 1 OF 1
29/02/08GA
UNLESS OTHERWISE SPECIFIED:
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
GALVFINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN MMTOLERANCES: 1.0mmFRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
APPLICATION
USED ONNEXT ASSY
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFMARCO CABLE MANAGEMENT. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFMARCO CABLE MANAGEMENT IS PROHIBITED.
5 4 3 2 1
3000
A
A
30
R10
1226
R7
1226
350
100
100
200
100
100
200
9610
2
C
DETAIL A SCALE 1 : 5
7
2212
7.208.20
13.2015.2020.2021.20
2526
R7
R6
DETAIL C SCALE 1 : 2
HOLE PATTERNS OF OBROUND SLOTSAND TABS ARE COPIED THROUGHOUTTHE 3 METER LENGTH OF THE PRODUCT.
DIVIDER SIZEMCD30 A = 24MMMCD55 A = 49MMMCD75 A = 74MM
MCD106 A = 100MM
CABLE TRAY DIVIDER
ADO NOT SCALE DRAWING
MA.01.02.0092SHEET 1 OF 1
29/02/08GA
UNLESS OTHERWISE SPECIFIED:
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
GALVFINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN MMTOLERANCES: 1.0mmFRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
APPLICATION
USED ONNEXT ASSY
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFMARCO CABLE MANAGEMENT. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFMARCO CABLE MANAGEMENT IS PROHIBITED.
5 4 3 2 1
3000
A
A
30
R10
1226
R7
1226
350
100
100
200
100
100
200
9610
2
C
DETAIL A SCALE 1 : 5
7
2212
7.208.20
13.2015.2020.2021.20
2526
R7
R6
DETAIL C SCALE 1 : 2
HOLE PATTERNS OF OBROUND SLOTSAND TABS ARE COPIED THROUGHOUTTHE 3 METER LENGTH OF THE PRODUCT.
DIVIDER SIZEMCD30 A = 24MMMCD55 A = 49MMMCD75 A = 74MM
MCD106 A = 100MM
CABLE TRAY DIVIDER
ADO NOT SCALE DRAWING
MA.01.02.0092SHEET 1 OF 1
29/02/08GA
UNLESS OTHERWISE SPECIFIED:
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
GALVFINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN MMTOLERANCES: 1.0mmFRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
APPLICATION
USED ONNEXT ASSY
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFMARCO CABLE MANAGEMENT. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFMARCO CABLE MANAGEMENT IS PROHIBITED.
5 4 3 2 1
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.36.1MCDJB divider joining bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steel.Manufactured:
The above are typical test results and do not constitute any part of a specification
MCDJB - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCDJB
Product Description:Divider joining bracket
Product Dimensions:60 x 18 x 2 mm
Material Specification:(if applicable)65Mn Spring steel
C Si Mn P S Cr Ni Cu
0.63% 0.21% 0.99% 0.018% 0.016% 0.04% 0.04% 0.09%
Yield Strength 803 MPa
Tensile Strength 1080 MPa
Elongation 18%
Utilisation:Joining dividers together creating a safety edge(MCD30, 55 & 106)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.31.1MCDOP Drop out plate
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCDOP - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCDOP
Product DescriptionDrop out plate
Product Dimensions170 x 90 x 1.2mm
Material Specification:(if applicable)
Utilisation:Allows cabling to drop out of the steel wire cable tray, with a CAT6 compliant radius bend
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 01248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.18.1MCET16 Earth terminal
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCET16 - Brass
Product CodeMCET16
Product DescriptionEarth terminal
Product DimensionsØ8.4 X Ø33 X 2MM Aluminium Washer17mm A/F Brass M8 & M10 Threaded BossM8 X 1.25 X 15MM Brass Mush Head BoltM10 X 1.5 X 7mm Brass Slotted Grub Screw
Material Specification:(if applicable)C3604 Brass
Cu Pb Fe Fe+Sn Zn
60% 2.42% 0.102% 0.22% Rem
Yield Strength -
Tensile Strength 380 MPa
Elongation 30%
Utilisation:Brass screw and alumnium washer used for earth termination
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Technical Data Sheet
TDFB24.1.1MCFB70 Cavity floor box
Issue Date: 06/2017[Page 1 of 1]
BS EN 60670 (Boxes and enclosures for electrical accessories)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
Product CodeMCFB370
Product DescriptionMCFB370 - Cavity floor box 70 mm 3 comp
Product Dimensions300 x 205 x 70 mm
Material Specification:(if applicable)
Utilisation:
6 mm recess for floor covering20 & 25 mm knockouts to accept all types of conduit2 cable outlets providing 60 x 15 mm openings 4 x spring fixing-clips for quick and secure fit
Galv-DX51D-Z2v75-M-A-CE:
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
70
FINAL 70MM BoxWEIGHT:
A3
SHEET 1 OF 1SCALE:1:5
DWG NO.
TITLE:
REVISIONDO NOT SCALE DRAWING
MATERIAL:
DATESIGNATURENAME
DEBUR AND BREAK SHARP EDGES
FINISH:UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
MCFB470
MCFB470 - Cavity floor box 70 mm 4 comp
Typical Properties Test Method Units PA-766B
Tensile Strength ASTM D-638 kg/cm2 400
Flexural Strength ASTM D-790 kg/cm2 650
IZOD Impact Strength ASTM D-256 kg-cm/cm 25
Vicat Softening Temp ASTM D-1525 XC 92
Melt Flow Index ASTM D-1238 200XC, 5kgg/10min (cond.G) 4.2
Flammability UL-94 File NO E56070UL & C-UL
1/10” V-0 1/8”5VA
A Calcium/Zinc stabilised, medium/high impact uPVC:
Reversible & interchangeable lid, integral moulded lifting-handle, Pre-fitted dividing fillets, Openings lined with soft sponge for cable protection
Product description:
Test method IEC 60068-2-75
Test reference TR11.1
300
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Technical Data Sheet
TDFB24.2.1MCFB100 Cavity floor box
Issue Date: 06/2017[Page 1 of 1]
BS EN 60670 (Boxes and enclosures for electrical accessories)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
Product CodeMCFB3100
Product DescriptionMCFB3100 - Cavity floor box 100 mm 3 comp
Product Dimensions300 x 205 x 100 mm
Material Specification:(if applicable)
Utilisation:
6 mm recess for floor covering20 & 25 mm knockouts to accept all types of conduit2 cable outlets providing 60 x 15 mm openings 4 x spring fixing-clips for quick and secure fit
Galv-DX51D-Z2v75-M-A-CE:
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
100
MCFB4100
MCFB4100 - Cavity floor box 100 mm 4 comp
Typical Properties Test Method Units PA-766B
Tensile Strength ASTM D-638 kg/cm2 400
Flexural Strength ASTM D-790 kg/cm2 650
IZOD Impact Strength ASTM D-256 kg-cm/cm 25
Vicat Softening Temp ASTM D-1525 XC 92
Melt Flow Index ASTM D-1238 200XC, 5kgg/10min (cond.G) 4.2
Flammability UL-94 File NO E56070UL & C-UL
1/10” V-0 1/8”5VA
A Calcium/Zinc stabilised, medium/high impact uPVC:
Reversible & interchangeable lid, integral moulded lifting-handle, Pre-fitted dividing fillets, Openings lined with soft sponge for cable protection
Product description:
Test method IEC 60068-2-75
Test reference TR11.1
300
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Technical Data Sheet
TDFB24.3.1MCFB130 Cavity floor box
Issue Date: 06/2017[Page 1 of 1]
BS EN 60670 (Boxes and enclosures for electrical accessories)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
Product CodeMCFB3130
Product DescriptionMCFB3130 - Cavity floor box 130 mm 3 comp
Product Dimensions300 x 205 x 130 mm
Material Specification:(if applicable)
Utilisation:
6 mm recess for floor covering20 & 25 mm knockouts to accept all types of conduit2 cable outlets providing 60 x 15 mm openings 4 x spring fixing-clips for quick and secure fit
Galv-DX51D-Z2v75-M-A-CE:
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
130
MCFB4130
MCFB4130 - Cavity floor box 130 mm 4 comp
Typical Properties Test Method Units PA-766B
Tensile Strength ASTM D-638 kg/cm2 400
Flexural Strength ASTM D-790 kg/cm2 650
IZOD Impact Strength ASTM D-256 kg-cm/cm 25
Vicat Softening Temp ASTM D-1525 XC 92
Melt Flow Index ASTM D-1238 200XC, 5kgg/10min (cond.G) 4.2
Flammability UL-94 File NO E56070UL & C-UL
1/10” V-0 1/8”5VA
A Calcium/Zinc stabilised, medium/high impact uPVC:
Reversible & interchangeable lid, integral moulded lifting-handle, Pre-fitted dividing fillets, Openings lined with soft sponge for cable protection
Product description:
Test method IEC 60068-2-75
Test reference TR11.1
300
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.24.1MCFCP Flexible conduit plate
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCFCP - Electro Zinc (EZ), suitable for use with EZ and PG cable trays
Product CodeMCFCPMCFCPGT
Product DescriptionFlexible conduit plate
Product Dimensions100 x 36.5 x 43.5 mm
Material Specification:(if applicable)
MCFCPGT - GT 321 (Geomet®), suitable for use with HDG and PG cable trays
Utilisation:Attached to steel wire cable tray in order to duct flexible conduit of either 20 or 25mm diameter
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.25.1MCFCP3 Flexible conduit plate 32mm
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCFCP3 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCFCP3
Product DescriptionFlexible conduit plate 32mm
Product Dimensions93 x 60 x 29 mm
Material Specification:(if applicable)
Utilisation:Attached to steel wire cable tray in order to channel flexible conduit of either 22, 25 or 32 mm diameter
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
1.2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.29.1MCFFB Fast fix floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
1 mm thick material
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCFFB - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCFFB
Product DescriptionFast fix floor bracket
Product Dimensions98 x 60 x 56mm
Material Specification:(if applicable)
Utilisation:Bracket used for securing steel wire cable tray to flooring without the need for a clamp
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.10.1MCFJC Fast joining coupler
Issue Date: 06/2017[Page 1 of 1]
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCFJC- Electro Zinc (EZ), suitable for use with EZ cable trays
Product CodeMCFJC
Product DescriptionFast joining coupler
Product Dimensions115 x 20 x 1.2 mm
Material Specification:(if applicable)65Mn Sprung steel
Yield Strength 785 MPa
Tensile Strength 981 MPa
Elongation 21%
Utilisation:Couple the following steel wire cable trays:MC5550MC55100MC55150MC55200
C S Si Mn P Cr Ni Cu
0.65% 0.018% 0.25% 1.13% 0.021% 0.22% 0.19% 0.17%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.12.1MCFJC-L Fast joining coupler large
Issue Date: 06/2017[Page 1 of 1]
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCFJC-L - Electro Zinc (EZ), suitable for use with EZ cable trays
Product CodeMCFJC-L
Product DescriptionFast joining coupler large
Product Dimensions117 x 18.5 x 1.2 mm
Material Specification:(if applicable)65Mn Sprung steel
Yield Strength 785 MPa
Tensile Strength 981 MPa
Elongation 21%
C S Si Mn P Cr Ni Cu
0.65% 0.018% 0.25% 1.13% 0.021% 0.22% 0.19% 0.17%
Utilisation:Couple the following steel wire cable trays:MC106300MC106400MC106450MC106500MC106600MC55400MC55450MC55500MC55600
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.11.1MCFJC-M Fast joining coupler medium
Issue Date: 06/2017[Page 1 of 1]
Manufactured:
The above are typical test results and do not constitute any part of a specification
MCFJC-M - Electro Zinc (EZ), suitable for use with EZ cable trays
Product CodeMCFJC-M
Product DescriptionFast joining coupler medium
Product Dimensions116.50 x 18.5 x 1. 20 mm
Material Specification:(if applicable)65Mn Sprung steel
C S Si Mn P Cr Ni Cu
0.65% 0.018% 0.25% 1.13% 0.021% 0.22% 0.19% 0.17%
Yield Strength 785 MPa
Tensile Strength 981 MPa
Elongation 21%
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steel
Utilisation:Couple the following steel wire cable trays:MC106100MC106150MC106200MC55300
tel: +44 (0) 1248 725 772 fax: +44 (0) 01248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.15.1MCFUSC Fast fix strut clip
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 1461 (Hot dip galvanized coatings)
0.9mm thick material
Power pressed from stripped steel.Manufactured:
The above are typical test results and do not constitute any part of a specification
MUFUSC - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Product Code:MCFUSC
Product Description:Fast fix universal strut clip
Product Dimensions:62 x 33 x 17 mm
Material Specification:(if applicable)65Mn Sprung Steel
C Si Mn P S Cr Ni Cu
0.65% 0.21% 0.96% 0.012% 0.007% 0.02% 0.03% 0.11%
Yield Strength 855 MPa
Tensile Strength 1050 MPa
Elongation 19%
Utilisation:Attaching steel wire cable tray to strut
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS22.4.1MCG6V0 Steel wire cable tray
Issue Date: 08/2017[Page 1 of 1]
Manufactured: Machine welded from steel wire rod
EZ - Electro-Zinc
Product Code:MCG60 Range
Product Description:60mm high G-shaped steel wire cable tray 50 x 100 mm mesh configuration
Product Dimensions:MCG6060 - 60 x 50 mm MCG60100 - 60 x 100 mmMCG60150 - 60 x 150 mmMCG60200 - 60 x 200 mm
HDG - Hot-dip Galvanised
PG - Pre-GalvanisedPC - Powder Coated
Standard 3 metres length
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)BS EN ISO 1461(Hot dip galvanized coatings)BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN 13438 (Powder organic coatings)
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.38.1MCL Steel wire cable tray lid
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCL - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Code:MCL Range
Product Description:Steel wire cable tray lid
Product Dimensions:
MCL100 - 2000 x 74 x 1 mmMCL150 - 2000 x 124 x 1 mmMCL200 - 2000 x 174 x 1 mmMCL300 - 2000 x 224 x 1 mmMCL400 - 2000 x 329 x 1 mmMCL450 - 2000 x 429 x 1 mmMCL500 - 2000 x 529 x 1 mmMCL600 - 2000 x 579 x 1 mm
Material Specification:(if applicable)
Utilisation:Cover for varying sizes of steel wire cable tray to protect the cables from dust and debris
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
B C
200
0
A
WIDTH
221
3.50
7.50101118
9.510.524.526.5
DETAIL A SCALE 1 : 1
85.50 171
97
9 DETAIL C SCALE 1 : 2
FLAT PATTERN
TRAY SIZE WIDTH50 74mm100 124mm150 174mm200 224mm300 329mm400 429mm450 479mm500 529mm600 579mm
CABLE TRAY LID
BDO NOT SCALE DRAWING
MA.01.02.0088SHEET 1 OF 1
07/03/08GA
UNLESS OTHERWISE SPECIFIED:
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
GALVFINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN MMTOLERANCES: 2mmFRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
APPLICATION
USED ONNEXT ASSY
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFMARCO CABLE MANAGEMENT. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFMARCO CABLE MANAGEMENT IS PROHIBITED.
5 4 3 2 1
B C 2
000
A
WIDTH
221
3.50
7.50101118
9.510.524.526.5
DETAIL A SCALE 1 : 1
85.50 171
97
9 DETAIL C SCALE 1 : 2
FLAT PATTERN
TRAY SIZE WIDTH50 74mm100 124mm150 174mm200 224mm300 329mm400 429mm450 479mm500 529mm600 579mm
CABLE TRAY LID
BDO NOT SCALE DRAWING
MA.01.02.0088SHEET 1 OF 1
07/03/08GA
UNLESS OTHERWISE SPECIFIED:
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
GALVFINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN MMTOLERANCES: 2mmFRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
APPLICATION
USED ONNEXT ASSY
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFMARCO CABLE MANAGEMENT. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFMARCO CABLE MANAGEMENT IS PROHIBITED.
5 4 3 2 1
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.5.1MCM620 Screw
Issue Date: 08/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Machined from steel barsManufactured:
MCM620 - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCM620
Product Description:M6 x 20 screw
Product Dimensions:25 x 16.5 x 16.5 mm
MCM620GT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Constituent part of both MCCA and MCCB
MCM620GT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.6MCM620NW screw, nut and washer
Issue Date: 058/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Machined from steel barsManufactured:
MCM620NW - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCM620NW
Product Description:M6 x 20 screw, nut and washer
Product Dimensions:25 x 16.5 x 16.5 mm
MCM620NWGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:Constituent part of both MCCA and MCCB
MCM620NWGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.28.1MCMFP Multi fix plate
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCMFP - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCMFP
Product DescriptionMulti fix plate
Product Dimensions125 x 85 x 2mm
Material Specification:(if applicable)
Utilisation:Multi-fix plate for securing steel wire cable tray to a number of surfaces or mounting accessories to steel wire cable tray
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.7.1MCQC Quick coupler
Issue Date: 07/2017[Page 1 of 2]
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCQC - Electro Zinc (EZ), suitable for use with EZ cable trays
Product CodeMCQC
Product DescriptionQuick coupler
Product Dimensions230 x 18.5 x 1.40 mm
Material Specification:(if applicable)65Mn Sprung steel
Yield Strength 785 MPa
Tensile Strength 981 MPa
Elongation 21%
Utilisation:Couple steel wire cable trays
C Si Mn P S Cr Ni Cu Mo
0.67% 0.25% 0.97% 0.024% 0.005% 0.05% 0.015% 0.063% 0.002%
MCQCGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
For use with MC30, MC55 and MC105 trays
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.7.1MCQC/MCQCP Quick coupler & puller
Issue Date: 07/2017[Page 2 of 2]
Product CodeMCQCP
Product DescriptionQuick coupler puller
Product Dimensions210 x 13 x 2.5 mm
Utilisation:Removing MCQC from trays
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCQCP - Electro Zinc (EZ), suitable for use with EZ cable trays
Material Specification:(if applicable)MS 2.5mm Q235
C Si Mn P S
0.16% 0.24% 0.43% 0.015% 0.021%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.17.1MCQLL Quick lock large
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steel.Manufactured:
The above are typical test results and do not constitute any part of a specification
MCQLL - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCQLL
Product Description:Large quick lock for trays from 300mm to 600mm wide
Product Dimensions:27 x 18 x 1.50mm
Material Specification:(if applicable)MS 1.5mm Q235
C Si Mn P S
0.17% 0.14% 0.24% 0.001% 0.002%
Yield Strength 355 MPa
Tensile Strength 459 MPa
Elongation 40%
Utilisation:Creating large radius bendsBuilt in locking tab used with flat-head screw driver
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.16.1MCQLS Quick lock small
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCQLS - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCQLS
Product Description:Small quick lock for trays 100 mm to 200 mm in width
Product Dimensions:22 x 18 x 1.10mm
Material Specification:(if applicable)MS 1.10mm Q235
C Si Mn P S
0.18% 0.11% 0.26% 0.011% 0.001%
Yield Strength 351 MPa
Tensile Strength 453 MPa
Elongation 36%
Utilisation:Creating large radius bendsBuilt in locking tab used with flat-head screw driver
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.32.1MCSB50 Suspension bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSB50 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSB50
Product DescriptionSuspension bracket for MC3050 and MC5550
Product Dimensions71 x 50 x 130 mm
Material Specification:(if applicable)
Utilisation:To suspend steel wire cable tray from threaded rod
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.21.1MCSB68 Suspension bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
2 mm thick material
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSB68 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSB68
Product DescriptionSuspension bracket for 6mm and 8mm threaded rod
Product Dimensions56.5 x 33 x 35 mm
Material Specification:(if applicable)
Utilisation:Suspend steel wire cable trays from 6 to 8 mm threaded rod
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
100kgMax safe working load:
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.32.1MCSB100 Suspension bracket
Issue Date: 08/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSB100
Product DescriptionSuspension bracket for MC30100 and MC55100
Product Dimensions121 x 50 x 130mm
Material Specification:(if applicable)
Utilisation:To suspend steel wire cable tray from a threaded rod
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.34.1MCSB150 Suspension bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
MCSB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSB150
Product DescriptionSuspension bracket for MC30150 and MC55150
Product Dimensions171 x 50 x 150mm
Material Specification:(if applicable)
Utilisation:To suspend steel wire cable tray from threaded
The above are typical test results and do not constitute any part of a specification
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.22.1MCSB1012 Suspension bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
2mm thick material
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSB1012 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSB1012
Product DescriptionSuspension bracket for 10 and 12mm threaded rod
Product Dimensions56.5 35 x 33mm
Material Specification:(if applicable)
Utilisation:Suspend steel wire cable trays from 10 to 12mm threaded rod
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.14.1MCSH Suspension hanger
Issue Date: 05/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSH - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCSH
Product Description:Suspension Hanger
Product Dimensions:59.5 x 37 x 2mm
Material Specification:(if applicable)MS 2mm Q235
C Si Mn P S
0.14% 0.12% 0.41% 0.02% 0.002%
Yield Strength 275 MPa
Tensile Strength 402 MPa
Elongation 27%
MCSHGT - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Utilisation:To suspend steel wire cable tray from threaded rod (Up to M10)
MCSHGT
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.19.1MCSP Splice plate
(Issue Date) [05/2017][Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)BS EN ISO 1461(Hot dip galvanized coatings)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSP - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSPMCSPGT
Product DescriptionSplice plate
Product Dimensions270 x 18.5 x 2mm
Material Specification:(if applicable)
MCSPGT - GT 321 (Geomet®), suitable for use with HDG and PG cable trays
Utilisation:Coupling steel wire cable trays, creating reducers,creating large radius bends
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.20.1MCSP90 Splice plate with 90 degree bend
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)BS EN ISO 1461 (Hot dip galvanized coatings)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSP90 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCSP90
Product DescriptionSplice plate with 90 degree bend
Product Dimensions247 x 18.5 x 2mm
Material Specification:(if applicable)
MCSP90GT - GT 321 (Geomet®), suitable for use with HDG and PG cable trays
Utilisation:Creating tee-junctions with right angle and crossovers
MCSP90GT
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.8.1MCSSC Side support coupler
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 1461 (Hot dip galvanized coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSSC - GT 321 (Geomet®), suitable for use with EZ, HDG and PG cable trays
Product Code:MCSSC
Product Description:Side support coupler to fit MC5550 - MC55200
Product Dimensions:42 x 32 x 0.9mm
Material Specification:(if applicable)65Mn Sprung Steel
C Si Mn P S Cr Ni Cu
0.65% 0.21% 0.96% 0.012% 0.007% 0.02% 0.03% 0.11%
Yield Strength 855 MPa
Tensile Strength 1050 MPa
Elongation 19%
Utilisation:Couple steel wire cable trays Locked in place using hex screwdriver
Additional information:Patented Product
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.9.1MCSSCL Large side support coupler
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 2081 (Metallic and other inorganic coatings)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCSSCL - Electro Zinc (EZ), suitable for use with EZ cable trays
Product Code:MCSSCL
Product Description:Large side support coupler to fit MC55300-600 & MC106 range
Product Dimensions:41.50 x 32 x 0.9mm
Material Specification:(if applicable)65Mn Sprung steel
C Si Mn P S Cr Ni Cu
0.64% 0.19% 0.94% 0.007% 0.017% 0.12% 0.08% 0.14%
Yield Strength 867 MPa
Tensile Strength 1060 MPa
Elongation 17%
Utilisation:Couple steel wire cable trays
Additional Information:Patented Product
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.27.1MCTS35 Tray support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
0.9mm material thickness
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCTS35 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCTS35
Product DescriptionTray support bracket for MC3050 and MC5550
Product Dimensions69 x 34 x 46mm
Material Specification:(if applicable)
Utilisation:Used to support 50mm width steel wire cable trays
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.30.1MCUSB Universal support bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCUSB - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCUSB
Product DescriptionUniversal support bracket
Product Dimensions190 x 120 x 2mm
Material Specification:(if applicable)
Utilisation:Allowing universal fitting of accessories on side of steelwire cable tray
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.38.1MCWB50 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB50 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB50
Product DescriptionWall/floor bracket for 50 mm steel wire cable tray
Product Dimensions118 x 40 x 35 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB100 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB100
Product DescriptionWall/floor bracket for 100 mm steel wire cable tray
Product Dimensions168 x 40 x 35 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB150 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB150
Product DescriptionWall/floor bracket for 150 mm steel wire cable tray
Product Dimensions218 x 40 x 35 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB200 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB200 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB200
Product DescriptionWall/floor bracket for 200 mm steel wire cable tray
Product Dimensions300 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB300 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB300 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB300
Product DescriptionWall/floor bracket for 300 mm steel wire cable tray
Product Dimensions402 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB400 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB400 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB400
Product DescriptionWall/floor bracket for 400 mm steel wire cable tray
Product Dimensions502 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB450 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB450 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB450
Product DescriptionWall/floor bracket for 450 mm steel wire cable tray
Product Dimensions552 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB500 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB500 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB500
Product DescriptionWall/floor bracket for 500 mm steel wire cable tray
Product Dimensions600 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.37.1MCWB600 Wall/Floor bracket
Issue Date: 06/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems) BS EN ISO 10244 (Steel wire and wire products)
Punched from sheet steelManufactured:
The above are typical test results and do not constitute any part of a specification
MCWB600 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product CodeMCWB600
Product DescriptionWall/floor bracket for 600 mm steel wire cable tray
Product Dimensions702 x 40 x 50 mm
Material Specification:(if applicable)
Utilisation:Securing steel wire cable tray to wall/floor
Galv-DX51D-Z275-M-A-CE
Fe Mn AI Si P Nb Ti
95% 1.7% 2% 0.6% 0.1% 0.09% 0.3%
Yield Strength -
Tensile Strength 270 - 500 MPa
Elongation ≥ 22%
2 mm thick material
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Applicable Standards:
Product Specification:
Finishes:
Technical Data Sheet
TDS20.41.1MCWFB100 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB100 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Code:MCWFB100
Product Description:Fast fix wall bracket for 100 mm steel wire cable tray
Product Dimensions:171.5 x 126.5 x 64.5 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.41.1MCWFB150 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
Product Code:MCWFB150
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB150 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Description:Fast fix wall bracket for 150 mm steel wire cable tray
Product Dimensions:221.5 x 126.5 x 58 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.41.1MCWFB200 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
Product Code:MCWFB200
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB200 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Description:Fast fix wall bracket for 200 mm steel wire cable tray
Product Dimensions:272 x 127 x 64.5 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.41.1MCWFB300 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
Product Code:MCWFB300
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB300 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Description:Fast fix wall bracket for 300 mm steel wire cable tray
Product Dimensions:371.5 x 127 x 64.5 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.41.1MCWFB400 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
Product Code:MCWFB400
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB400 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Description:Fast fix wall bracket for 400 mm steel wire cable tray
Product Dimensions:471.5 x 186.5 x 64.5 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%
tel: +44 (0) 1248 725 772 fax: +44 (0) 1248 725 772 email: [email protected] web: www.marcocm.com
Technical Data Sheet
TDS20.41.1MCWFB450 Fast fix wall bracket
Issue Date: 07/2017[Page 1 of 1]
Product Code:MCWFB450
Applicable Standards:
Product Specification:
Finishes:
BS EN 61537 (Cable tray systems)BS EN 10244 (Steel wire and wire products)
Power pressed from stripped steelManufactured:
MCWFB450 - Pre-Galvanised (PG), suitable for use with EZ and PG cable trays
Product Description:Fast fix wall bracket for 450 mm steel wire cable tray
Product Dimensions:521.5 x 186.5 x 64.5 mm
Utilisation:Support steel wire cable tray from walls without the use of clamps
The above are typical test results and do not constitute any part of a specification
Material Specification:(if applicable)Galv To EN 10142 DX52 D+Z
C Mn P S Si Ti
≤ 0.120 % ≤ 0.6 % ≤ 0.100 % ≤ 0.045% ≤ 0.5% ≤ 0.300 %
1.5 mm material thickness
Yield Strength 140-300 MPa
Tensile Strength 270 - 420 MPa
Elongation ≥ 26%