tcc 2700 operation instructions manual
TRANSCRIPT
![Page 1: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/1.jpg)
Remove machine from carton and place on a stable surface.Remove machine from plastic bag
Remove bubble-wrap from mandrills
TCC 2700 Laminating MachineOperating Instructions
TCC 2700 Laminating MachineOperating Instructions
![Page 2: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/2.jpg)
Lower mandrill inside laminating roll
Upper mandrill inside the laminating roll
Lower heat roller
Upper heat roller
Operating Panel
TCC 2700 Laminating MachineTCC 2700 Laminating Machine
![Page 3: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/3.jpg)
Upper MandrillLower Mandrill
Laminating roll Laminating roll
![Page 4: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/4.jpg)
Insert upper and lowermandrills into core of thefilm
Line up film with appropriate notches on mandrill (25” film lines
up with notch that reads “25”” and so forth)
![Page 5: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/5.jpg)
Upper Mandrill inside the laminating roll Lower Mandrill inside the laminating roll
After inserting the upper and lower mandrills into the core of the film, it should look like the pictures
shown below
![Page 6: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/6.jpg)
How to thread the laminating filmHow to thread the laminating filmshiny side
dull side
UPPER HEAT ROLLER
LOWER HEAT ROLLER
dull side
shiny side
laminating roll
laminating roll
Upper mandrill
Lower mandrill
Threading Bars
![Page 7: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/7.jpg)
Pass film over the first threading bar
Threading the upper laminating rollThreading the upper laminating roll
![Page 8: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/8.jpg)
Pull film towards front and over the second threading bar
Threading the upper laminating rollThreading the upper laminating roll
![Page 9: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/9.jpg)
Pass film over stable support rod
Threading the lower laminating rollThreading the lower laminating roll
![Page 10: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/10.jpg)
Pass film under and back over the lower threading bar
Threading the lower laminating rollThreading the lower laminating roll
![Page 11: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/11.jpg)
Threading the lower laminating rollThreading the lower laminating roll
Pull through and over the upper threading bar
![Page 12: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/12.jpg)
Both ends of film should meet at heated rollers
![Page 13: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/13.jpg)
Switch on the machine Set speed to “1”
Switching on the machine and settingSwitching on the machine and setting
![Page 14: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/14.jpg)
Insert both ends of the film in-between the upper and lower heat rollers using the threading card (should come with the
laminating rolls)
Once the film is fed fully through the machine, set lever to
“UP” position
Setting up the machineSetting up the machine
![Page 15: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/15.jpg)
Set temperature to desired heat level and press the
heat button
At this time, the machine will take a few minutes to heat up
At 80 degrees Celsius, you will hear a beep from themachine. This is to let you know that when the temperaturereaches 90 degrees, the rollers will start to turn. Press heatbutton again to silence beeping.
At 90 degrees Celsius, the roller will start turning. If thelever is in the “UP” position, the rollers are thereforeseparated, the machine should not pull any film through.
The chart at the top left hand side ofthe machine will give you ourrecommended setting for differentthicknesses of film (settings may varydepending upon material)
![Page 16: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/16.jpg)
Align the feed tray with appropriate notches, and set into place.
Machine will beep once again when desired temperature is reached and
green ready light will go on.
![Page 17: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/17.jpg)
Lever should always be in “UP” position when machine is NOT in use
Lever should be in “DOWN” positionwhen machine is in use
Lever positionsLever positions
![Page 18: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/18.jpg)
Trim blade
The trim blade is used to separate yourcurrent laminated project from the restof the material.
Caution: The blade is very sharp andshould be used with utmost care.
Run blade through material from left to right to cut finished product from the
rest of the film.
When not in use, trim blade should be set on the left side of the machine
Trim bladeTrim blade
![Page 19: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/19.jpg)
Feed the papers to be laminated in between the upper and lower heat
rollers, as shown above
Gently pull the laminated paper at the back. (if you don’t pull, the laminated paper might attach to the machine and get
wrinkled, due to static electricity)
FeedingFeeding
![Page 20: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/20.jpg)
Set the temperature to 80 degrees Celsius.
Press Cold button – the machine will start to cool down
Press and hold speed down button for 3 – 5 secondsto set the speed to “0”. (if running at a higher speedthan “1”, reduce speed to “1” and then set to “0”)
When the machine reaches 80 degrees Celsius, it isnow safe to turn machine off by setting the power switchto “OFF”
Switching off the machineSwitching off the machine
![Page 21: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/21.jpg)
Tension can be adjusted for the purpose ofcreating the right resistance for the rolls oflaminating film.
This is achieved by turning the silver knobs on the right side of the machine that line up with the upper and lower mandrills.
To decrease tension, turn knob counter-clockwise. .
To increase tension, turn knob clockwise.
Wrinkles
Trouble shootingTrouble shooting
![Page 22: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/22.jpg)
Reverse ButtonReverse button is used to back the film out incase of any jams or errors in lamination.
When pressed, the film will feed back outtowards the front of the machine. Whenreleased, the machine will start feeding thefilm normally again.
Trouble shootingTrouble shooting
![Page 23: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/23.jpg)
Glue Buildup
When machine is improperly heated to toohigh temperature or film is improperly aligned,you may notice markings along the side of thefilm where excess glue is building up on therollers.
To properly remove the glue, please use anon-abrasive cleaning solution (such asGooGone) that will not damage the rollersthemselves.
Do not use sharp or abrasive tool to scratchglue from rollers. Use a clean cloth and acleaning solution to scrub away build up.
Trouble shootingTrouble shooting
![Page 24: TCC 2700 Operation Instructions Manual](https://reader031.vdocuments.us/reader031/viewer/2022020108/5870ba6a1a28ab5a048b762c/html5/thumbnails/24.jpg)
Operating instructions manualOperating instructions manual
Refer the enclosed instructions manual for additional information