tc compass manual - tc arms...tc_compass_manual_080118_3005599.qxp_tc compass manual 8/13/18 11:57...

Safety & Instruction Manual

Bolt-Action Rifle

THOMPSON/CENTER ARMS

2100 Roosevelt Avenue

Springfield, MA 01104

Toll Free Phone (866) 730-1614

www.tcarms.com

Read the instructions andwarnings in this manual

CAREFULLY BEFORE using this firearm.

Copyright © 2018 Smith & Wesson Corp.

All rights reserved.

The rifle may be shown throughout thismanual with optional equipment installed(for educational purposes).

Many of the procedures outlined in this manual are covered in videos that can be viewed at:

www.tcarms.com/compass

TC_COMPASS_Manual_080118_3005599.Qxp_TC Compass Manual 8/13/18 11:57 AM

2

WARNINGREAD THESE

INSTRUCTIONS AND WARNINGS CAREFULLY.

BE SURE YOU UNDERSTAND THESE INSTRUCTIONS AND

WARNINGS BEFORE USING THISFIREARM. FAILURE TO READ THESE

INSTRUCTIONS AND TO FOLLOWTHESE WARNINGS MAY RESULT IN

SERIOUS INJURY OR DEATH TO YOU AND OTHERS AND DAMAGE TO PROPERTY

This SAFETY & INSTRUCTIONMANUAL should always accompany thisfirearm and be transferred with it upon

change of ownership or when thefirearm is presented to another person.

Always keep your firearm pointed in asafe direction. Never point a firearm atanything you do not intend to shoot.

If you don’t have a manual, printedcopies are available free upon request

by contacting the factory at the addressbelow. They are also available

via download at www.tcarms.com.

THOMPSON/CENTER ARMS• CUSTOMER SUPPORT •2100 Roosevelt AvenueSpringfield, MA 01104

Toll Free Phone (866) 730-1614Website: www.tcarms.com

Customer Service Email:[email protected]


3

YOUR SAFETYRESPONSIBILITIES

SAFETY IS YOUR NUMBER ONE

RESPONSIBILITY!!!!

• At home, in the field, at the range, or anywhere, the first concernof every firearm owner should be safety. Apply the following safetyrules in every situation, with any kind of firearm. If you feel uncer-tain about any operational aspects of your firearm, please contactThompson/Center @ 866-730-1614 before proceeding with itsoperation.

• If you are unfamiliar with firearms you should seek formal trainingbefore using your rifle.

WARNING: YOU MUST FOLLOW ALL OF THESE SAFETYRULES TO ENSURE THE SAFE USE OF YOUR FIREARM.THE FAILURE TO FOLLOW THE INSTRUCTIONS AND

WARNINGS IN THIS MANUAL COULD CAUSE SERIOUS PERSON-AL INJURY OR DEATH TO YOU OR OTHERS AND DAMAGE TOPROPERTY.

• As a firearm owner, you accept a demanding responsibility. How seriously you take this responsibility can be the differencebetween life and death. There is no excuse for careless or abu-sive handling of your firearm. At all times handle your firearm with intense respect for its power and potential danger.

TABLE OF CONTENTS

YOUR SAFETY RESPONSIBILITIES . . . . . . . . . . . . . . . . .3-6

SAFE STORAGE AND TRANSPORTATION . . . . . . . . . . . .7-8

PREPARATION FOR FIRING . . . . . . . . . . . . . . . . . . . . . . . .9

AMMUNITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11

MODEL AND FEATURES IDENTIFICATION . . . . . . . . . . . .12

INSPECTING AND INITIAL ASSEMBLY . . . . . . . . . . . .13-16

LOADING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

FIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

CLEARING MISFIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

UNLOADING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-20

DISASSEMBLY / FIELD STRIPPING . . . . . . . . . . . . . . .21-22

SCOPE MOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

MAKING TRIGGER ADJUSTMENTS . . . . . . . . . . . . . . .24-27

CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . .28-30

DETAILED BOLT DISASSEMBLY FOR CLEANING . . . .30-31

BOLT REASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . .32-34

LIMITED LIFETIME WARRANTY . . . . . . . . . . . . . . . . . .35-36

BATTERY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

CONTACT AND SHIPPING / PATENT INFORMATION .38-39

ADDRESSES AND PHONE NUMBERS . . . . . . . . . . . . . . .40


4

YOUR SAFETY RESPONSIBILITIES CONTINUED

• ALWAYS KEEP YOUR FIREARM POINTED IN A SAFE DIREC-TION. Never point a firearm at anyone or anything you do notintend to shoot whether or not it is loaded. This is particularlyimportant when loading, unloading, or field stripping the firearm.ALWAYS control the direction of the firearm.

• ALWAYS TREAT EVERY FIREARM AS IF IT IS LOADED ANDWILL FIRE. Do not take anyone’s word that the firearm isunloaded – always check for yourself. Never pass your firearm toanother person until the action is open and you visually checkthat it is unloaded. Keep your firearm unloaded and safely storedwhen not in use.

• NEVER PLACE YOUR FINGER INSIDE THE TRIGGER GUARDOR ON THE TRIGGER UNLESS YOU INTEND TO FIRE. Ensurethat other objects do not touch the trigger.

• ALWAYS BE SURE OF YOUR TARGET AND WHAT IS BEYONDIT. Always be sure of where the bullet will strike and shoot onlywhere there is a safe backstop free of obstructions, water orother surfaces which can cause ricochets. Be sure your bulletwill stop behind your target. Bullets can glance off many sur-faces like rocks or the surface of water and travel in unpre-dictable directions with considerable velocity. Do not fire ran-domly into the sky.

• NEVER CROSS OBSTACLES SUCH AS FENCES ORSTREAMS WITH A LOADED FIREARM. Always make certainyour firearm is unloaded before crossing a fence, climbing a tree,jumping a ditch or negotiating other obstacles.

• SAFE FIREARM HANDLING IS YOUR PERSONAL RESPONSI-BILITY AT ALL TIMES. Firearms are dangerous and can causeserious injury or death if they are misused or used inappropriate-ly. Safety must be the prime consideration of any one who ownsor handles firearms. Accidents are the result of violating the rulesof safe firearm handling and common sense. Firearm safetytraining is available. Contact your firearms dealer, law enforce-ment agency, local sportsman’s club, etc. for availability.

• YOU ARE RESPONSIBLE FOR THE FIREARM AT ALL TIMES.In owning a firearm, you must undertake full-time responsibilityfor your firearm’s safety and security. You must protect yourselfand all others against injury or death from misuse of the firearm24 hours a day.

• FIREARM SECURITY IS YOUR RESPONSIBILITY. You mustsecure firearms safely from children and/or unauthorized users.Your firearm should always be kept unloaded and locked whennot in use. Never assume that the use of the provided lock issufficient to safely secure your firearm. You must always evaluateyour personal situation and employ the security systems thatmeet your needs and prevent children and unauthorized usersfrom gaining access to your firearm.


5


• APPROPRIATE USE FOR YOUR FIREARM MEANS USINGYOUR FIREARM FOR LEGAL PURPOSES. For example - targetshooting, hunting and lawful resistance of deadly criminal force.It is your responsibility to ensure that you are in compliance withall applicable laws and ordinances regarding the use of yourfirearm.

• NEVER RELY ON MECHANICAL FEATURES ALONE. Only yoursafe firearm-handling habits will ensure the safe use of yourfirearm. This is your responsibility.

• ALWAYS SAFELY STORE AND SECURE YOUR FIREARM. Safeand secure storage of your firearm is one of your most importantresponsibilities. It is a full-time responsibility. You must alwayssecure your firearm and ammunition separately so that they arenot accessible to children and/or other unauthorized persons.

• NEVER KEEP AMMUNITION IN THE SAME LOCATION ASTHE FIREARM. Store each in a separate and secure place.

• ALWAYS WEAR EYE PROTECTION THAT IS SPECIFIED FORUSE WITH FIREARMS every time you handle your firearm forcleaning and maintenance.

• ALWAYS WEAR EYE AND HEARING PROTECTION THAT ARESPECIFIED FOR USE WITH FIREARMS every time you dis-charge your firearm. Make sure others in the vicinity of whereyou will be shooting do so as well.

• NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILESHOOTING. Do not use your firearm if you are on any medica-tion which impairs, even slightly, your mental or physical ability.

• ALWAYS HAVE ADEQUATE VENTILATION. Discharging firearmsin poorly ventilated areas, cleaning firearms, or handling ammu-nition may result in exposure to lead and other substancesknown to cause birth defects, reproductive harm, and other seri-ous physical injury. Review the warnings and labels for all ammu-nition and cleaning products carefully. Wash hands thoroughlyafter exposure.

• BEFORE HANDLING ANY FIREARM, UNDERSTAND ITSOPERATION. Not all firearms are the same. Familiarize yourselfwith the mechanical features of any firearm you intend to use. Ifyou feel uncertain about any operational aspects of your firearm,please contact Thompson/Center™, before proceeding with itsoperation.

• NEVER ALLOW A FIREARM TO BE USED BY INDIVIDUALS

WHO DO NOT UNDERSTAND ITS SAFE OPERATION OR

HAVE NOT READ THESE FIREARM SAFETY RULES.


6


• ALWAYS USE THE CORRECT AMMUNITION FOR YOURPARTICULAR FIREARM as indicated by the marking on thefirearm. Never use non-standard, damaged, corroded orreloaded, (handloaded) ammunition which has not been sub-jected to internal ballistic pressure testing.

• BEWARE OF BARREL OBSTRUCTIONS Be sure the barrel isclear of obstructions before shooting. Mud, water, snow or otherobjects may inadvertently lodge in the barrel bore. A smallobstruction can cause a dangerous increase in pressure and maydamage your firearm and cause injury to yourself and others.

• BE SURE ALL ACCESSORIES, SUCH AS SLINGS, SCOPESAND OTHER ACCESSORIES ARE COMPATIBLE with thefirearm and that the accessories do not interfere with safe opera-tion. It is your responsibility to understand and follow all of theinstructions in this manual,as well as those which may be sup-plied with your ammunition and any accessory.

• NEVER DISASSEMBLE YOUR FIREARM beyond the field strip-ping procedure outlined in this manual. Improper disassembly orreassembly of your firearm may be dangerous and can lead toserious injury or death.

• NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THEINTERNAL COMPONENTS OF YOUR FIREARM UNLESSSPECIFICALLY INSTRUCTED TO DO SO IN THIS MANUAL.Improper manipulation of any other internal component mayaffect the safety and reliability of your firearm and may causeserious injury or death.

• NEVER ALLOW ANY ALTERATION OR REPLACEMENT OFPARTS IN YOUR THOMPSON/CENTER™ FIREARM UNLESSPERFORMED BY A QUALIFIED GUNSMITH using genuineThompson/Center™ parts. If you do otherwise, improper func-tioning of your firearm may occur and serious injury or death anddamage to property may result.

WARNING: SAFE USE OF A FIREARM IS YOUR PERSON-AL RESPONSIBILITY AND THE FAILURE TO FOLLOW ALLOF THESE BASIC SAFETY RULES MAY RESULT IN

SEVERE PERSONAL INJURY OR DEATH TO YOU OR OTHERSAND DAMAGE TO PROPERTY. YOU ARE THE MOST IMPORTANTSAFETY DEVICE WHEN IT COMES TO THE USE OF YOURFIREARM AND THOMPSON/CENTER AND ITS PARENT COMPA-NY WILL NOT BE RESPONSIBLE FOR ANY PERSONAL INJURY,DEATH OR PROPERTY DAMAGE THAT RESULTS FROM: (1) THE CRIMINAL OR NEGLIGENT USE OF THIS FIREARM; (2) A DISREGARD OF THESE SAFETY INSTRUCTIONS ANDWARNINGS; (3) IMPROPER OR CARELESS HANDLING OF THISFIREARM; (4) THE USE OF NON-STANDARD, DEFECTIVE ORIMPROPER AMMUNITION; (5) IMPROPER OR NEGLIGENT MODI-FICATIONS OR REPAIRS TO THE FIREARM.


7

SAFE STORAGE ANDTRANSPORTATION

WARNING: ALWAYS POINT THE MUZZLE IN A SAFEDIRECTION.

WARNING: FIREARMS ARE DANGEROUS WHEN USEDAND STORED IMPROPERLY. THEY POSE A RISK OFSERIOUS OR FATAL INJURIES. FIREARMS CAN BE

ESPECIALLY DANGEROUS TO CHILDREN WHEN THEY ARESTORED IN AN IRRESPONSIBLE AND UNSAFE MANNER. FORYOUR SAFETY AND THE SAFETY OF OTHERS, IT IS IMPERA-TIVE THAT YOU KEEP YOUR FIREARM LOCKED ANDUNLOADED IN A SECURE PLACE. THE AMMUNITION SHOULDBE STORED IN A SEPARATE, SECURE LOCATION WHEN IT ISNOT IN USE. SAFE AND SECURE STORAGE OF YOURFIREARM IS ONE OF THE MOST IMPORTANT RULES OFFIREARM SAFETY. YOUR FAILURE TO FOLLOW THESE RULESMAY RESULT IN SERIOUS INJURY OR DEATH TO YOU OROTHERS.

• ALWAYS SECURE YOUR FIREARM IN A MANNER THAT WILLPREVENT UNAUTHORIZED ACCESS. Whenever your firearm isnot in use, keep it unloaded and locked. Your safety and thesafety of others requires that you always secure and store yourfirearm in a manner that will prevent unauthorized access. Neverleave a firearm unattended unless it is locked, unloaded andsecured.

• ALWAYS USE THE LOCK PROVIDED BY THOMPSON/CENTER™

TO SECURE YOUR FIREARM. Please read and follow the instruc-tions packaged separately for the use of this lock. A lock, whenproperly used, can be an effective tool in preventing unautho-rized access to your firearm. There are other alternative locksand safe storage containers available in the marketplace whichmay also be appropriate for your particular needs. Consult yourlocal gun shop, hardware store, or local police department forguidance on the variety of other safe storage devices or prac-tices which may be appropriate for your particular needs. By pur-chasing this firearm you have accepted the responsibility of safe-ly securing the firearm at all times and preventing its unautho-rized use. Never assume that the use of this lock alone is suffi-cient to safely secure your firearm. It is your personal responsi-bility to select and use whatever measures or practices that willenable you to be absolutely certain that your firearm is secure atall times.

WARNING: NEVER LOCK A LOADED FIREARM ANDNEVER LOAD A LOCKED FIREARM!!


8

SAFE STORAGE AND TRANSPORTATION CONTINUED

• ALWAYS STORE YOUR FIREARM AND AMMUNITION SEPA-RATELY so that they are not accessible to children or otherunauthorized persons. Safe and secure storage of your firearmand ammunition are your responsibility. It is a full-time responsi-bility.

• NEVER ASSUME THAT A “HIDING” PLACE IS A SECURESTORAGE METHOD. Others may be aware of your storage loca-tion or come upon it by chance. It is your personal responsibilityto use common sense when storing your firearm and ammunitionand to always make sure they are not accessible to children orother unauthorized persons.

• NEVER TRANSPORT A LOADED FIREARM. When transportingyour firearm, be sure it is unloaded and locked. Safe and securetransportation of your firearm is your responsibility.

• ALWAYS FOLLOW THE LAW. Many jurisdictions have laws thatmake it a crime to keep a firearm unlocked and in an area acces-sible to children or others. Keeping a firearm locked andunloaded when not in use is not only common sense safety prac-tice... IT IS THE LAW. You must be familiar with all local, state,and federal laws regarding the safe storage and transportation ofyour firearm. Failure to know and follow the law may result inunauthorized access or use of your firearm by another. Obey alllaws relating to the storage and transportation of firearms. Yourlocal police department or gun shop can furnish you with avail-able information on storing and/or transporting a firearm safelyand legally.

• YOUR FIREARM IS YOUR RESPONSIBILITY. You must preventyour firearm from being stolen or from being used by untrained orunqualified individuals. Keep it locked, unloaded and securedwhen not in use.

• Use the lock provided to prevent unauthorized use, follow theinstructions supplied with the lock.

• Never leave the key with the stored firearm.


9

PREPARATION FOR FIRINGWARNING: FAILURE TO FOLLOW THESE FIREARMSAFETY REQUIREMENTS WILL CAUSE SERIOUS PER-SONAL INJURY OR DEATH TO YOU OR OTHERS.

• ALWAYS TREAT ALL FIREARMS AS IF THEY ARE LOADED.

• ALWAYS BE SURE THAT ALL CYLINDERS AND ACTIONS OFFIREARMS ARE OPEN, THAT CHAMBER(S) ARE CLEAR OFCARTRIDGES OR SHELLS, MAGAZINES ARE REMOVED ORUNLOADED, AND THAT FIREARMS ARE POINTING IN A SAFEDIRECTION.

• ALWAYS WEAR ADEQUATE AND PROPER HEARING PRO-TECTION SPECIFIED FOR FIREARM USE to prevent perma-nent damage to your hearing. Make sure others who are nearbyare wearing hearing protection as well.

• ALWAYS WEAR SAFETY GLASSES SPECIFIED FOR USEWITH FIREARMS, whether indoors or out. Safety glasses shouldprotect your eyes from the firing flash and particles associatedwith the discharge of ammunition. Failure to wear the proper eyeprotection creates a risk of personal injury from particle or debrisspitting or ricochets.

• ALWAYS BE ALERT AND ALWAYS FOLLOW THE SAFETYINSTRUCTIONS OF THE RANGE OFFICER. Never shoot if youare tired, cold or impaired in any way.

• ALWAYS BE AWARE OF OTHER PEOPLE so that persons donot accidentally walk into the line of fire.

• THE SHOOTER (AND ALL OTHERS IN THE SHOOTING AREA)MUST ALWAYS BE IN A POSITION THAT IS OUT OF THELINE OF FIRE and are not within an area where they may bestruck by a ricochet or particles spitting from a firearm, or byejected cases from some types of firearms.

• NEVER SHOOT AT SURFACES THAT MAY CAUSE A RICO-CHET. Always select a place to shoot that has a safe backstop,is free from obstructions and has no surfaces which may cause aricochet.

• NEVER FIRE RANDOMLY INTO THE SKY. Always select aplace to shoot that has a safe backstop.

• NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILESHOOTING OR HANDLING ANY FIREARM.


10

AMMUNITIONWARNING: NEVER USE AMMUNITION NOT SPECIFI-CALLY DESIGNATED FOR USE IN YOUR FIREARM.FAILURE TO USE THE CORRECT TYPE OR CALIBER

OF AMMUNITION MAY CAUSE THE FIREARM TO JAM, ORFAIL TO FIRE, OR MAY GENERATE EXCESSIVE PRESSUREWHICH CAN DAMAGE OR EVEN RUPTURE YOUR FIREARM,CAUSING PERSONAL INJURY OR DEATH TO THE SHOOTEROR BYSTANDERS.

• Locate the cartridge desig-nation marked on thefirearm. This informationindicates the correctammunition that must beused in this firearm (FIGURE 1).

• You are responsible forselecting ammunition thatmeets industry standardsand is appropriate in typeand caliber for this firearm.

* Never mix ammunition.

WARNING: IN SOMECASES, A ROUNDOF AMMUNITION

NOT SPECIFIED ON YOUR FIREARM AND NOT LISTED ASALTERNATE AMMUNITION IN THIS MANUAL, MAY FIT INTOTHE CHAMBER. FIRING THIS AMMUNITION MAY CAUSE ARUPTURE RESULTING IN DAMAGE TO THE FIREARM ANDPERSONAL INJURY OR DEATH TO THE SHOOTER ORBYSTANDERS. FOR MORE INFORMATION REGARDINGUNSAFE CALIBER COMBINATIONS, REFER TO THE FOLLOW-ING URL: HTTP://WWW.SAAMI.ORG/SPECIFICATIONS_AND_INFOR-

MATION/PUBLICATIONS/DOWNLOAD/SAAMI_ITEM_211-

UNSAFE_ARMS_AND_AMMUNITION_COMBINATIONS.PDF

WARNING: ALWAYS INSPECT YOUR AMMUNITIONBEFORE USING IT. NEVER USE DIRTY, CORRODED ORDAMAGED AMMUNITION. A BURST CARTRIDGE OR

BORE OBSTRUCTION MAY RESULT CAUSING DAMAGE TOTHE FIREARM AND PERSONAL INJURY OR DEATH TO THESHOOTER OR BYSTANDERS.

• Use only commercially manufactured ammunition with internalballistic pressures which are in strict accordance with the speci-fications of the Sporting Arms and Ammunition Manufacturers’Institute (SAAMI). If you are uncertain, contact your ammunitionsupplier for verification.

FIGURE 1

Cartridge Designation in TwoPlaces - 1) on top of Barrel

2) on Right Side


11

AMMUNITION CONTINUED

WARNING: NEVER USE NON-STANDARD, RELOADEDOR “HANDLOADED” AMMUNITION WHICH HAS NOTBEEN SUBJECTED TO INTERNAL BALLISTIC PRESSURE

TESTING. RELOADED OR HANDLOADED AMMUNITION, MAYHAVE MANY MANUFACTURING AND QUALITY VARIABLES(SUCH AS THE TYPE AND AMOUNT OF GUN POWDER). CAR-TRIDGE CASES THAT HAVE BEEN RELOADED AND FIRED MUL-TIPLE TIMES MAY SUFFER PHYSICAL DAMAGE WHICH COULDSIGNIFICANTLY IMPACT OR REDUCE THE INTEGRITY OF THECARTRIDGE, POSSIBLY RESULTING IN BULLET SETBACK ORUNSEATING. CASE FAILURE AND INJURY TO THE SHOOTEROR BYSTANDERS AND DAMAGE TO THE FIREARM MAYRESULT WHEN SUCH A ROUND IS FIRED. ANY AMMUNITIONTHAT IS IMPROPERLY MANUFACTURED OR RELOADED, EVENIN THE SLIGHTEST DEGREE, MAY FAIL TO FIRE OR MAY GEN-ERATE EXCESSIVE INTERNAL PRESSURES WHICH CAN DAM-AGE OR EVEN RUPTURE THE FIREARM, CAUSING PERSONALINJURY OR DEATH TO THE SHOOTER OR THOSE IN THEIMMEDIATE VICINITY.

• A firearm and ammunition are a system and must work together.There are different types of ammunition for different types offirearms. Your firearm has been designed for ammunition of a spe-cific type and a specific gauge or caliber. It is important to selectthe proper ammunition for your firearm.

• Different combinations of bullet velocity, bullet weight and firearmweight can have major impact on felt recoil; a high level of feltrecoil can be uncomfortable to some shooters.

WARNING: NEVER USE AMMUNITION OF THEINCORRECT GAUGE OR CALIBER. USING AMMUNI-TION OF THE INCORRECT GAUGE OR CALIBER MAY

CAUSE DAMAGE TO YOUR FIREARM AND POSSIBLE SERI-OUS INJURY TO YOU AND TO OTHERS.

WARNING: DEATH, SERIOUS INJURY AND PROPER-TY DAMAGE CAN RESULT FROM THE USE OFINCORRECT AMMUNITION OR BORE OBSTRUC-

TIONS. NEVER USE RELOADED AMMUNITION THAT HASNOT BEEN SUBJECTED TO INTERNAL BALLISTIC PRES-SURE TESTING.

WARNING: DISCHARGING FIREARMS IN POORLY VENTI-LATED AREAS, CLEANING FIREARMS, OR HANDLINGAMMUNITION MAY RESULT IN EXPOSURE TO LEAD

AND OTHER SUBSTANCES KNOWN TO CAUSE BIRTHDEFECTS, REPRODUCTIVE HARM, AND OTHER SERIOUSPHYSICAL INJURY. HAVE ADEQUATE VENTILATION AT ALLTIMES. WASH HANDS THOROUGHLY AFTER EXPOSURE.


12

FIGURE 2a

MODEL NAME ON BARREL

BUTT PAD

MODEL AND FEATURESIDENTIFICATION

FIGURE 2d

Bolt stop location

FIGURE 2e

FIGURE 2c

Cocking indicator

Safety lever

SLINGSWIVELSTUD

BOLTHANDLE

Leave threadprotector inplace on

muzzle unlessdevices likeflash hidersand soundsuppressorsare installed.

STOCK

SAFETYLEVER

COCKINGINDICATOR

BOLTASSEMBLY

BARREL

FOREND

MAGAZINERELEASELATCH

MAGAZINE

TRIGGERGUARD

TRIGGER

FIGURE 2f

BOLT BODY

EXTRACTOR

EJECTOR

LOCKING LUGS (3)

FIGURE 2b

FIGURE 2g

MODEL NAME ON RECEIVER (on both sides)

MUZZLEWith threadprotector.Barrel is

threaded formuzzle

devices likeflash hidersand soundsuppressors.

RECEIVER

SCOPE MOUNT BASE

Serial number


13

INSPECTING ANDINITIAL ASSEMBLY

WARNING: ALWAYS ENSURE THAT THE FIREARM ISUNLOADED BEFORE INSPECTING, DISASSEMBLING,ASSEMBLING OR CLEANING AND ALWAYS KEEP THE

MUZZLE POINTED IN A SAFE DIRECTION.

• Your T/C® COMPASS® rifle comes completely assembled fromthe factory except for the bolt assembly, which has beenremoved for transportation and storage. The bolt assembly ispacked separately in the shipping carton.

WARNING: THE BOLT ASSEMBLY IN THE T/C®

COMPASS® RIFLE IS MATCHED SPECIFICALLY TO THERECEIVER. BOLT ASSEMBLIES ARE NOT INTER-

CHANGEABLE BETWEEN RIFLES. THE LAST FOUR DIGITS OFTHE RIFLE’S SERIAL NUMBER ARE MARKED ON THE COR-RECT BOLT SHROUD (FIGURE3) AND BOLT HEAD (FIGURE 4)FOR THAT PARTICULAR RIFLE.NO ATTEMPT SHOULD BEMADE TO USE ANY BOLT IN ARECEIVER THAT DOES NOTHAVE MATCHING NUMBERSAS INJURY AND/OR DEATH TO THE SHOOTER ORBYSTANDERS AND DAMAGETO PROPERTY MAY RESULT.

THE BOLT ASSEMBLY ISPACKAGED SEPARATELY INTHE BOX AS SHIPPED FROMTHE FACTORY. BEFOREINSTALLING THE BOLTASSEMBLY INTO THE RIFLE,CONFIRM THAT THE LASTFOUR DIGITS OF THE RIFLE’SSERIAL NUMBER ALSO APPEAR ON THE BOLT SHROUD ANDBOLT HEAD. IF A RIFLE AND BOLT ASSEMBLY ARE MIS-MATCHED, THE ENTIRE RIFLE MUST BE RETURNED TO THEFACTORY FOR PROPER FITTING OF A NEW BOLT ASSEMBLYTHAT WILL BEAR THE LAST FOUR DIGITS OF THE RIFLE’SSERIAL NUMBER.

INSPECTING YOUR RIFLE

• Grasp the rifle, keeping yourfinger outside the trigger guardand off the trigger, point themuzzle in a safe direction.

• Check to be certain that thechamber is empty (FIGURE 5).

FIGURE 5

Chamber empty

FIGURE 4

FIGURE 3

Location of last 4 digits of rifle’sserial number on bolt shroud

Location of the same last 4 digitsof rifle’s serial number on bolt head


INSPECTING AND INITIAL ASSEMBLY CONTINUED

• Press and hold the magazinelatch to the rear to release themagazine (FIGURE 6).

• Orient the rifle as shown toallow the magazine to comeout of the rifle when the maga-zine latch is released (FIGURE 7).

• Remove the magazine andensure that it is empty (FIGURE 8).

• Remove the T/C® COMPASS®

identifier from the barrel (FIG-URE 9). The rifle should not be used with the identifierattached.

INSTALLING THE BOLTASSEMBLY

NOTE: Don’t try to move thesafety lever with the bolt out ofthe rifle. The bolt must be in therifle in the closed position withthe firing pin cocked in order tomove the safety lever.

• Grasp the bolt by its handleand slide the bolt forward intothe receiver about one inch asshown (FIGURE 10).

• Rotate the bolt upward by thehandle (FIGURE 11) until thebolt stop engages the boltstop tracking groove in thebolt itself (FIGURE 12).

14FIGURE 11

Rotate bolt handle up until boltstop engages tracking groove

FIGURE 10

Start bolt assembly into receiver

Remove magazine

FIGURE 8

FIGURE 6

FIGURE 9

Press and hold latch to the rearto release the magazine

Remove the T/C® Compass®

identifier from barrel.

FIGURE 7

Unlatch and tip magazine down at the front first to remove it.


15


• Push the bolt fully forward intothe receiver once the bolt stopengages the tracking groove inthe bolt (FIGURE 12).

• Close the bolt by turning thebolt handle down (FIGURE 13).

The Safety Lever

WARNING: NEVERRELY ON MECHANI-CAL FEATURES

ALONE. ONLY YOUR SAFEFIREARM HANDLING WILLENSURE THE SAFE USE OFYOUR FIREARM. THIS ISYOUR RESPONSIBILITY.

• Located on the right side at therear of the bolt, the safety leverhas three (3) positions that areset by the user when the bolt isin the closed and cocked posi-tion: “BL” (BOLT LOCKED-SAFE), “S” SAFE and “F” FIRE (FIGURE 14).

• Cocking indicator is visiblenear the back of the boltshroud when the rifle is cocked(FIGURE 15). The indicator isrecessed when the firing pin isin the FIRED position (FIGURE16). The safety lever can onlybe moved when the rifle iscocked and the bolt is closed.Cock the rifle by lifting the bolthandle fully and then closing it.

Bolt in

closed

position

FIGURE 13

Safety lever

FIGURE 12

Bolt stop

BOLT LOCKEDSAFE

POSITION

FIREPOSITIONSAFE

POSITION

Bolt stop tracking groove

FIGURE 14

FIGURE 16

FIGURE 15

Cocked position

Fired position


16


• Fully rearward - In the “BL”BOLT LOCKED SAFE position(FIGURE 17). Bolt is lockedclosed and the rifle is in SAFEmode.

• The middle position - “S” -SAFE LOAD/UNLOAD (FIGURE 18) The rifle is inSAFE mode - but the bolt canbe manipulated to load andunload the rifle’s chamber.

• Fully forward in the - “F” FIREposition (FIGURE 19) the riflecan be fired by pulling rear-ward on the trigger.

WARNING: DO NOT ALTER, MODIFY OR REPLACEANY OF THE PARTS OF YOUR FIREARM UNLESSTHIS WORK IS PERFORMED BY A QUALIFIED GUN-

SMITH USING GENUINE THOMPSON/CENTER™ PARTS. IFYOU DO OTHERWISE, IMPROPER FUNCTIONING MAYOCCUR AND SERIOUS INJURY OR DEATH MAY RESULT.

WARNING: NEVER DO ANYTHING BEYOND WHATYOU ARE SPECIFICALLY INSTRUCTED TO DO INTHIS MANUAL. NEVER ALTER OR MODIFY THE

PARTS IN YOUR FIREARM.

• Before using your firearm for the first time, it should be cleaned.See the Cleaning section of this manual.

FIGURE 17

Safety lever fully rearward in the “BOLT LOCKED - SAFE ”

position

FIGURE 18

Safety lever in the middle“SAFE” LOAD/UNLOAD

position

FIGURE 19

Safety lever fully forward in the “FIRE” position


17

LOADINGWARNING: ALWAYSPOINT THE MUZZLE INA SAFE DIRECTION.

WARNING: NEVERCARRY THIS RIFLE WITHA CARTRIDGE IN THE

CHAMBER. FAILURE TO FOLLOWTHIS INSTRUCTION CAN LEADTO PERSONAL INJURY ORDEATH TO YOU OR OTHERS AND DAMAGE TO PROPERTY.

• Open the bolt (FIGURE 20) andinspect the bore for obstruc-tions (and follow the cleaninginstructions in this manual ifnecessary - see page 28).

• Keep your finger outside thetrigger guard and off the trig-ger, point the muzzle in a safedirection.

• Do not load the rifle until youhave read and fully understandthis manual.

• Do not load the rifle until youare ready to use it.

• Never load your rifle until youare sure of your target, what isbeyond it and are fully pre-pared to fire.

• Close the bolt on an emptychamber and then place thesafety lever in the “SAFE” posi-tion (FIGURE 21).

• Remove the magazine from therifle in order to load the car-tridges into it. Insert the car-tridges into the magazine asshown (FIGURES 22 and 23).

• Just prior to firing, with the boltclosed on an empty chamber,insert the loaded magazine intoplace - tipping the back end infirst and then lifting the frontuntil it “clicks” into position(FIGURE 24).

Bolt in

Unlocked

Position

FIGURE 20

FIGURE 21

Safety in middle “SAFE”position

An audible “click” indicates that

the bolt is all the way up.

LOADED MAGAZINE5 round capacity for std calibers,

4 round capacity for magnums

FIGURE 23

FIGURE 24

Loading the magazine

FIGURE 22

Insert rear first - then tip front up to latch

Press the loaded cartridge(s) down to aid in starting next round


FIRINGWARNING: ALWAYS KEEP THE MUZZLE POINTED INA SAFE DIRECTION.

WARNING: WEAR EYE AND HEARING PROTECTIONSPECIFIED FOR FIREARM USE EVERY TIME YOUDISCHARGE YOUR FIREARM. MAKE SURE OTHERS

IN THE VICINITY OF WHERE YOU WILL BE SHOOTING DOSO AS WELL.

• With the bolt closed on anempty chamber, make certainthat the safety is in the “SAFE”LOAD/UNLOAD position (FIG-URE 25). You can move thesafety lever only when the fir-ing pin is cocked. If the firingpin is in the fired position, liftthe bolt handle fully and thenreturn it to the closed positionto allow the safety lever to bemoved.

• Open the bolt and draw it fullyto the rear, then push forwardand close bolt handle (with thebolt handle turned fully down)to strip a round from the maga-zine and put that round intothe chamber.

• Grasp the rifle with one handon the forend and other handon the grip with the trigger fin-ger resting along and outsideof the trigger guard. Raise therifle and pull buttstock firmly into shoulder.

• Push the safety lever to the fully forward “FIRE” position (FIG-URE 26).

• The rifle will now fire when pressure is applied to the trigger.

• When you are sure of your target and what is beyond it, placeyour finger on trigger and gently pull the trigger until the riflefires.

• You may continue to fire the rifle by fully opening and closing thebolt, which will eject the spent case and feed a new cartridgeinto the rifle, and then pulling the trigger. You may repeat thisprocess until the magazine is empty and the chamber is empty.

• To reload, see the Loading Section.

18

FIGURE 26

FIGURE 25


19

CLEARING MISFIRESWARNING: IF YOUR FIREARM GIVES ANY INDICATIONTHAT IT IS NOT PERFORMING PROPERLY OR THEOPERATION OF YOUR FIREARM HAS CHANGED “THE

WAY IT FEELS OR SOUNDS”, STOP FIRING. MAKE SURE THEFIREARM IS POINTED IN A SAFE DIRECTION, UNLOAD THEFIREARM AND CALL THOMPSON/CENTER™ CUSTOMERSUPPORT AT (866) 730-1614 TO HAVE IT INSPECTED BY AFACTORY TECHNICIAN.

• If a cartridge fails to fire, keep the muzzle pointed in a safe direc-tion and wait 30 seconds before opening the bolt and ejectingthe suspect cartridge. Then remove the magazine and make surethat the rifle is unloaded. Dispose of the defective cartridge in amethod specifically approved for live round disposal.

UNLOADINGWARNING: ALWAYSKEEP THE MUZZLEPOINTED IN A SAFE

DIRECTION.

• Open the bolt and ensure thatthe chamber is empty (FIGURES 27 and 28).

• Press and hold the magazinelatch (FIGURE 29) rearward.

• Remove the magazine from therifle (FIGURE 30).

FIGURE 30

Remove magazine

FIGURE 28

Make certain that the chamber is empty

Open bolt first

FIGURE 27

FIGURE 29

Magazine latch location


UNLOADING CONTINUED

• Close the bolt on an emptychamber (FIGURE 31).

• Set safety lever in the “SAFE”LOAD/UNLOAD position (FIGURE 32).

• Remove any cartridges fromthe magazine by holding themagazine in one hand andpushing the cartridges out withthe other (FIGURE 33).

20

Rotate the safety lever to the“SAFE” position

FIGURE 32

FIGURE 33

Remove cartridges from magazine

FIGURE 31


21

DISASSEMBLY /FIELD STRIPPING

WARNING: ALWAYS KEEP THE MUZZLE POINTED IN ASAFE DIRECTION.

WARNING: NEVER DO ANYTHING BEYOND WHAT YOUARE SPECIFICALLY INSTRUCTED TO DO IN THIS MAN-UAL. NEVER ALTER OR MODIFY THE PARTS IN YOUR

FIREARM.

WARNING: WEAR SAFETY GLASSES SPECIFIED FORUSE WITH FIREARMS EVERY TIME YOU ASSEMBLEOR DISASSEMBLE YOUR FIREARM.

WARNING: DO NOT ALTER, MODIFY OR REPLACE ANYOF THE PARTS OF YOUR FIREARM UNLESS THISWORK IS PERFORMED BY A QUALIFIED GUNSMITH

USING GENUINE THOMPSON/CENTER™ PARTS. IF YOU DOOTHERWISE, IMPROPER FUNCTIONING MAY OCCUR ANDSERIOUS INJURY OR DEATH MAY RESULT.

REMOVAL OF BOLT

• Lift the bolt handle and draw the bolt fully to the rear.

• Confirm that the chamber isempty (FIGURE 34).

• Remove magazine from rifle(FIGURE 35).

• Hold the magazine in one handand push any cartridges out ofthe magazine (FIGURE 36).

FIGURE 34

FIGURE 36

FIGURE 35


22

DISASSEMBLY / FIELD STRIPPING CONTINUED

• Close the bolt on an emptychamber (FIGURE 37).

• Set safety lever to the “SAFE”position (FIGURE 38).

• Open the bolt and draw it fullyrearward (FIGURE 39).

• Press the bolt stop in and holdit as shown (FIGURE 40).Continue to hold the bolt stopdepressed while you removethe bolt from the receiver witha gentle pull rearward.

• Withdraw the bolt fully, takingcare not to hit the stock - pos-sibly causing cosmetic damage(FIGURE 41).

NOTE: Under normal conditions,this is the extent of disassemblythat needs to be done for clean-ing or storage. For details on dis-assembling the bolt, see the boltdisassembly instructions in theCleaning and MaintenanceSection of this manual.

FIGURE 41

FIGURE 40

Remove bolt completely

Press andhold the

bolt-stop In

FIGURE 39

Place the safety lever in the “SAFE” position

FIGURE 38

FIGURE 37


23

SCOPE MOUNTWARNING: ALWAYS ENSURE THAT THE FIREARM ISUNLOADED BEFORE INSTALLING A SCOPE OR ANYOTHER ACCESSORIES. FAILURE TO DO THIS CAN

CAUSE PERSONAL INJURY OR DEATH TO YOU OR OTHERS.

We recommend that you have a competent gunsmith install yourscope and mount.

The T/C® COMPASS® is factory drilled and tapped for scopemount bases. Weaver®-style bases are included with the rifle.Different scopes have varying lengths of recommended eye relief.You need to choose a combination that allows for adequate clear-ance between the scope and your eye. Follow the instructions sup-plied with the scope and rings for proper installation (FIGURE 42).

WARNING: A SCOPE WHICH IS NOT SECURELYMOUNTED MAY BECOME DETACHED UPON RECOILOF THE FIREARM. IF IT BECOMES DETACHED IT

MAY FLY BACK AND STRIKE THE SHOOTER OR ABYSTANDER AND CAUSE INJURY. OBSERVE THE CONDI-TION OF ALL THE SCOPE MOUNT SCREWS AFTER FIRING.IF THE MOUNTING SCREWS SHOW SIGNS OF LOOSENINGDO NOT FIRE THE FIREARM AGAIN; TAKE IT TO A QUALI-FIED GUNSMITH FOR ASSISTANCE.

WARNING: FIRING A SCOPED FIREARM WITH YOUREYE TOO CLOSE TO THE SCOPE EYE PIECE, FAIL-ING TO HOLD THE FIREARM SECURELY AGAINST

RECOIL OR FAILING TO WEAR EYE PROTECTION THAT ISSPECIFIED FOR USE WITH FIREARMS, MAY RESULT INSERIOUS PERSONAL INJURY INCLUDING, BUT NOT LIMIT-ED TO, BLINDNESS.

FIGURE 42

Follow the instructions supplied with the scope and mounts to

ensure proper eye relief


24

MAKING TRIGGERADJUSTMENTS

WARNING: ALWAYS ENSURE THAT THE FIREARM ISUNLOADED BEFORE ADJUSTING THE TRIGGER ORDRY FIRING.

• The trigger has been adjusted at the factory for optimal perfor-mance.

• We recommend that you have a competent gunsmith adjust yourtrigger if needed. Do not attempt trigger adjustments unless youare confident in your ability tofollow these instructions fortrigger adjustment.

• Open the bolt fully (FIGURE 43).

• Remove the magazine from therifle and set it aside.

• Press and hold the bolt stopand remove the bolt from therifle (FIGURE 44).

• Remove the barreledaction from the stockto adjust the trigger.Use a 5/32˝ hexwrench to removethe 2 bolts (FIGURES45 and 46) that holdthe stock on.

• Set the stock aside.

FIGURE 45

FIGURE 46

FIGURE 43

FIGURE 44

Press andhold the

bolt stop in


25

MAKING TRIGGER ADJUSTMENTS CONTINUED

• There are three nuts on the trig-ger. The two nuts above the trig-ger adjust the tension on thespring that controls the weight ofpull and then lock against oneanother (FIGURE 47). These arereferred to as the weight of pulladjustment nut and weight of pulllock nut.

• The single nut below the triggeris used to lock the over-travelstop screw in its setting onceadjusted. It is referred to as theover-travel adjustment lock nut(FIGURE 47).

• The purpose of the over-traveladjustment screw is to adjust the amount of over-travel of the trigger.Over-travel is the amount of movement of the trigger beyond thatnecessary to complete its purpose (releasing the firing pin from thecocked position in this case).

CAUTION: If you screw the over-travel adjustment screw in too far, youwill not be able to pull the trigger enough to release the sear.

• Ideally the over-travel adjustment screw should be screwed in as faras possible but still allow enough trigger movement to consistentlyrelease the sear when the trigger is pulled.

• To make adjustments, you will need two (thin) 1/4", open-endwrenches, and a small screwdriver. Also, have a bottle of finger nailpolish handy to “lock” the screw and nuts in place after you have fin-ished all the adjustments.

• Start by adjusting for over-travel. Loosen all three nutsslightly away from the trig-ger and from each otherwith a 1/4" open-endwrench (FIGURE 48).

• Using a small screwdriver,turn the over-travel adjust-ment screw clockwise untilit bottoms out. Back thescrew up 1/4 to 1/2 turnfrom bottom.

• Snug the over-travel adjust-ment lock nut on the screwagainst the trigger to holdthe screw in this position.

FIGURE 47Weight of pull

adjustment nut

Weight of Pull Lock Nut

FIGURE 48

Over-travel adjustment screwand over-travel adjustment

screw lock nut



• Move the weight of pull locknut down to contact thetrigger (FIGURE 49). Lower the weight of pulladjustment nut against thelock nut and try the weightof pull by dry-firing theaction. This is the minimumweight of pull and minimumover-travel.

• Once adjusted, use the two1/4˝ wrenches to ensure thatthe weight of pull lock nut islocked against the adjust-ment nut. Also, check thatthe over-travel lock nut istight against the trigger(FIGURE 50).

• Put a small dab of fingernail polish on the threads to lock all of the nuts inposition.

• Don't put thread lock such as Loctite® on trigger screws or nuts.Instead, use a drop of nail polish on trigger screw threads to holdthe screws or nuts in place. Thread locker products can seize thesmall screws and nuts used in triggers, possibly making them verydifficult to adjust or remove at a later date.

LUBRICATION POINTS

• A single drop of light, non-con-gealing oil can be applied tothe sear engagement surface(FIGURE 51).

• The pivot points of the searand trigger can also be lubri-cated with a single drop oflight, non-congealing oil (FIGURE 52).

26

Trigger PivotPoints

FIGURE 51

Sear engagement surface

FIGURE 52

FIGURE 49

FIGURE 50



• Make certain the recoil lug isengaged with the stock correctlywhen the gun is reassembled (FIGURE 53).

• Reassemble the barreled actioninto the stock. Tighten the two5/32˝ hex head bolts at eitherend of the action (FIGURES 54and 55) until snug. The bolts areboth the same length and canbe interchanged.

WARNING: INCORRECTASSEMBLY MAYRESULT IN DAMAGE TO

THE FIREARM AND CREATEAN UNSAFE CONDITION.

NOTE: Be certain thatthe two trigger (fire-control) assembly pinsare centered side toside (not protrudingfrom either side) in thereceiver whenreassembling the bar-reled action into thestock (FIGURE 56). Ifthese pins are too farto the left or right theywill interfere with thestock and you will notbe able to engage thestock takedownscrews.

Dry Firing Note:

Be certain that the chamber isunloaded and the magazine isremoved from the rifle. Keep thefirearm pointed in a safe direction.The T/C® COMPASS® rifle can bedry fired without damage to the fir-ing pin or other components. Todry fire, cock the rifle by lifting thebolt handle fully and returning it tothe closed position and thenpulling the trigger - with the safetylever in the FIRE position.

27

FIGURE 53

Recoil Lug in stock

Recess in receiverthat accepts recoil lugwhen assembling

FIGURE 56

Trigger pins centered (side toside) in receiver

Pins not protrudingfrom either side

FIGURE 54

FIGURE 55


28

CLEANING AND MAINTENANCEWARNING: ENSURE THAT YOUR FIREARM ISUNLOADED BEFORE BEGINNING TO CLEAN IT. (SEE “INSPECTING YOUR FIREARM” SECTION).

ALWAYS FOLLOW THE RULES OF SAFE FIREARM HANDLING.

WARNING: WEAR EYE PROTECTION SPECIFIED FORFIREARM USE EVERY TIME YOU CLEAN OR MAINTAINYOUR FIREARM.

• Before using your firearm for the first time, it should be cleaned.

• Your firearm was treated at the factory with either a preservativeor oil to protect it against corrosion during shipping and storage.

• Preservative and oil should be wiped from the bore, chamberand exposed areas using a clean swab or patch before using thefirearm.

CAUTION: Never disassemble your firearm beyond the instructionsin the Field Stripping and Inspection sections of this manual.

• Purchase cleaning supplies from your firearms dealer that arespecifically designated for your type and caliber of firearm. Manysuppliers offer these in kit form for your convenience.

• Follow the instructions provided with your cleaning supplies.

NOTE: A basic firearm cleaning kit should include: a brass borebrush and a cleaning jag of appropriate size for the bore beingcleaned, high-quality gun cleaning solvent and gun oil/lubricant,cotton cleaning patches and a cleaning rod that is long enough to push the brush and jag completely through the barrel.

• Remove excessive firing residue from the bore and chamberusing a properly fitted brass brush dipped in gun cleaning sol-vent. Finish the bore cleaning process by running a dry cottoncloth patch through the bore to remove residue and solvent.

• Clean the exterior of the firearm using a non-abrasive cleaningcloth.

• After cleaning, lightly coat the metal parts, internal and externalwith a high quality firearm oil.

• Whenever your firearm has been exposed to sand, dust, extremehumidity, water or other adverse conditions, it must be cleanedand lubricated.


29

CLEANING AND MAINTENANCE CONTINUED

WARNING: ALWAYS HAVE ADEQUATE VENTILATION.CLEANING FIREARMS IN POORLY VENTILATED AREAS,DISCHARGING FIREARMS, OR HANDLING AMMUNI-

TION MAY RESULT IN EXPOSURE TO LEAD AND OTHER SUB-STANCES KNOWN TO CAUSE BIRTH DEFECTS, REPRODUC-TIVE HARM AND OTHER SERIOUS PHYSICAL INJURY. WASHHANDS THOROUGHLY AFTER EXPOSURE.

CAUTION: Always follow the instructions provided with your guncleaner and gun lubricant.

CAUTION: Some cleaners can cause damage to your firearms. Youshould avoid prolonged solvent immersion and prolonged ultrason-ic cleaning of your firearm. Choice of solvent should be restrictedto those products specifically developed for firearms maintenance.Damage to a firearm’s finish may occur if these cautions areignored. Ammoniated solvents or other strong alkaline solvents,should not be used on any Thompson/Center™ firearm. Cleaningis essential to ensure the proper functioning of your firearm.

• Your firearm is a precision instrument. To ensure reliable functionit is necessary to follow a routine maintenance procedure. Afterfiring your firearm, be sure to unload it following the procedureoutlined in the section entitled “Inspecting Your Firearm” beforeperforming any cleaning or maintenance procedure.

• Remove any gun cleaning solution, oil and fingerprints from theoutside surfaces of the firearm. (Finger moisture, if left, couldstart a corrosion process.)

WARNING: NEVER MANIPULATE, ADJUST OR CHANGEANY OF THE INTERNAL COMPONENTS OF YOURFIREARM UNLESS SPECIFICALLY DIRECTED TO DO SO

IN THIS MANUAL. IMPROPER MANIPULATION OF ANY INTER-NAL COMPONENT MAY AFFECT THE SAFETY AND RELIABILI-TY OF YOUR FIREARM AND MAY CAUSE SERIOUS INJURYOR DEATH. IT ALSO VOIDS YOUR WARRANTY.

WARNING: ANY MAINTENANCE, ADJUSTMENT ORSERVICE NOT SPECIFIED IN THIS MANUAL MAYAFFECT THE SAFETY AND RELIABILITY OF YOUR

FIREARM AND MUST BE PERFORMED BY A QUALIFIEDGUNSMITH USING GENUINE THOMPSON/CENTER™PARTS. IF YOU DO OTHERWISE, IMPROPER FUNCTIONINGOF YOUR FIREARM MAY OCCUR AND SERIOUS INJURY ORDEATH MAY RESULT.

• If your firearm will be used in a cold climate, be sure to use anoil of an appropriate weight so that it will not congeal in coldtemperatures, causing the interaction of important parts to beslowed or halted.


30

CLEANING AND MAINTENANCE CONTINUED

MAINTENANCE BEFORE STORAGE• When storing, do not encase your firearm in anything that will

attract or hold moisture, for example, leather or heavy cloth.Also, do not store guns with a plug inserted in the barrel for thiscan be a contributing factor to moisture accumulation. If yourfirearm is to be stored for an extended period, the bore, chamberand internal surfaces should be oiled with a high-quality lubricat-ing oil or preservative intended for firearms. The external parts;receiver, bolt and barrel should be coated with an anti-rust oil.Before using your firearm again, be sure to clean it. Every timeyou clean your firearm, check it for signs of wear. If wear isnoted, do not use the firearm. Return it to Thompson/Center™for service or have it checked by a qualified gunsmith.

DETAILED BOLT DISASSEMBLY FOR CLEANING

• The bolt may be disassembledfor cleaning (FIGURE 57 & 58).

• Do not attempt to disassemblethe firing pin assembly beyondwhat is covered in this manual.

• The bolt handle is held in place underspring tension. This spring tension mustbe released to allow the bolt handle tobe removed from the bolt body, therebyallowing the firing pin assembly to beremoved from the bolt body.

IMPORTANT NOTE: The first step in thisprocess - with the bolt closed on an empty chamber in the rifle - isto place the safety lever in the SAFE position (FIGURE 59).

FIGURE 58

FIGURE 57

Bolt Handle

Bolt Body

Firing PinAssembly

Bolt Head- has last 4digits of

rifle’s serialnumber

Bolt HeadRetainer Pin

Bolt Assembly

Bolt Shroud - has last 4 digitsof rifle’s serial number

FIGURE 59


31

DETAILED BOLT DISASSEMBLY FOR CLEANING CONTINUED

• Remove the bolt from the rifle.

• When the bolt was removedfrom the receiver, the firing pinwas cocked (FIGURE 60).

• Uncock the firing pin. To dothis, grasp the bolt body in onehand and the bolt shroud androtate the bolt shroud to movethe firing pin assembly from thecocked position to theuncocked position (FIGURES 61 and 62).

• Press the bolt shroud against ahard surface to relieve springtension and at the same time -pull the bolt handle clear of thebolt body (FIGURE 63).

• After the bolt handle is pulledfree of the bolt body (FIGURE64) the firing pin assembly canbe removed from the bolt body- allowing it to be cleaned andlightly lubricated.

NOTE: Some jiggling of the firingpin assembly may be required asyou pull on it to allow it to bepulled free of the bolt body.

• After the firing pin assembly ispulled free of the bolt body thebolt head retainer pin and bolthead can be removed from thebolt body - allowing them to becleaned and lightly lubricated(FIGURE 65).

FIGURE 62

FIGURE 63

2) WithdrawBolt Handle

FIGURE 64

WithdrawFiring Pin Assembly

FIGURE 61

FIGURE 60

Firing Pinin theCockedPosition

Hold Handle.Turn BoltShroud

Firing Pin inthe UncockedPosition

1) Pressand Hold

BoltShroudAgainst

HardSurface

FIGURE 65

1) Remove Bolt Head Retainer Pin2) Remove Bolt Head

1)

2)


32

BOLT REASSEMBLY

WARNING: THE BOLTASSEMBLY IN THE T/C®

COMPASS® RIFLE ISMATCHED SPECIFICALLY TOTHE RECEIVER. BOLTASSEMBLIES ARE NOT INTER-CHANGEABLE BETWEENRIFLES. THE LAST FOUR DIG-ITS OF THE RIFLE’S SERIALNUMBER ARE MARKED ONTHE CORRECT BOLT SHROUD(FIGURE 66) AND BOLT HEAD(FIGURE 67) FOR THAT PAR-TICULAR RIFLE. NO ATTEMPTSHOULD BE MADE TO USEANY BOLT IN A RECEIVERTHAT DOES NOT HAVEMATCHING NUMBERS ASINJURY AND/OR DEATH TOTHE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPER-TY MAY RESULT.

THE BOLT ASSEMBLY IS PACKAGED SEPARATELY IN THE BOXAS SHIPPED FROM THE FACTORY. BEFORE INSTALLING THEBOLT ASSEMBLY INTO THE RIFLE, CONFIRM THAT THE LASTFOUR DIGITS OF THE RIFLE’S SERIAL NUMBER ALSOAPPEAR ON THE BOLT SHROUD AND BOLT HEAD. IF A RIFLEAND BOLT ASSEMBLY ARE MIS-MATCHED, THE ENTIRE RIFLEMUST BE RETURNED TO THE FACTORY FOR PROPER FIT-TING OF A NEW BOLT ASSEMBLY THAT WILL BEAR THE LASTFOUR DIGITS OF THE RIFLE’S SERIAL NUMBER.

• When reassembling the bolt,put the bolt head and bolt headretaining pin back into the boltbody. The retaining pin will onlyenter the bolt body and bolthead in one direction - wheneverything is lined up correctly(FIGURE 68).

• Return the bolt head into thebolt body (FIGURE 69) andinstall the bolt head retainingpin.

FIGURE 68

The pin can only enter the boltbody from one direction.

SmallDiameter Section

LargeDiameterSection

FIGURE 69

Step 2 - Insert BoltHead Retainer Pin

Step 1- Insert Bolt Head

FIGURE 67

FIGURE 66

Location of last 4 digits of rifle’sserial number on bolt shroud

Location of the same last 4 digitsof rifle’s serial number on bolt head


33

BOLT REASSEMBLY CONTINUED

• Then, return the firing pinassembly into the bolt body.Keep the firing pin assembly inthe uncocked position (FIGURE 70).

• Press the bolt shroud against ahard surface to compressspring slightly. Insert the bolthandle into the bolt body slot(FIGURE 71).

• Pull on the bolt handle toensure that it is assembled cor-rectly and held securely inplace by the cocked firing pinassembly. If the bolt handlecomes free when pulled, it wasnot installed properly, repeatassembly procedure and try topull the handle out again until itremains in place when pulled.

• After the bolt handle is re-installed, the firing pin mustnow be re-cocked by graspingthe bolt body in one hand andturning the bolt shroud with theother hand. An audible “click”indicates that the firing pin isre-cocked (FIGURES 72, 73and 74).

FIGURE 73

FIGURE 72

Firing Pin in the UncockedPosition

FIGURE 74 Firing Pinin theCockedPosition

2)InsertBolt

Handle1) PressBolt

AgainstHard

Surface

FIGURE 71

FIGURE 70

Insert FiringPin Assembly

into BoltBody

UncockedPosition


34

BOLT REASSEMBLY CONTINUED

NOTE: The firing pin must becocked to allow the bolt to beinstalled back into the receiver.Failure to re-cock the firing pinbefore installing the bolt backinto the receiver could result incosmetic damage to the stock asthe parts won’t be aligned cor-rectly and the stock may inter-fere.

• Re-install bolt into receiver(FIGURES 75 and 76) andcheck for proper functioning.

WARNING: NEVER MANIPULATE, ADJUST ORCHANGE ANY OF THE INTERNAL COMPONENTS OFYOUR FIREARM UNLESS SPECIFICALLY DIRECTED

TO DO SO IN THIS MANUAL. IMPROPER MANIPULATION OFANY INTERNAL COMPONENT MAY AFFECT THE SAFETYAND RELIABILITY OF YOUR FIREARM AND MAY CAUSESERIOUS INJURY OR DEATH.

FIGURE 76

Rotate Bolt Handle Up Until the Bolt Stop Engages the

Tracking Groove

FIGURE 75

Start Bolt Into Receiver


35

LIMITED LIFETIME WARRANTYThis warranty is granted by Smith & Wesson Corp. doing businessas Thompson/Center Arms™. This warranty is effective from thedate of purchase for the lifetime of the original retail purchaser ofany factory finished firearm. In order to be eligible for service underthis warranty, the original retail purchaser must return a completedauthorized warranty card or register online athttp://www.tcarms.com/warranty-details/registration within thirty(30) days of purchase of such firearm. With respect to such firearm,this warranty supersedes any and all other warranties.

Thompson/Center Arms™ brand firearms are warranted to be freefrom defects in material and workmanship. Any such defects ofwhich Smith & Wesson® receives written notice by the original retailpurchaser will be remedied without charge within a reasonable timeafter such notification and delivery of the firearm as provided below.

Warranty claims (in writing) and the firearm or part thereof con-cerned should be delivered, postage prepaid, to the factory atSmith & Wesson, 2100 Roosevelt Ave., Springfield, MA 01104, Attn: Service Department. In addition, a copy of the bill of sale inthe original retail purchaser’s name, or, where applicable, a copy ofATF Form 4473 indicating date of purchase must be included.Please include your physical address and phone number. You mustcomply with all applicable federal, state and local laws and regula-tions in the shipment of firearms to Smith & Wesson®.

NOTE: See the Contact And Shipping section of this manualfor further details regarding returns.

Warranty claims should state the model and, where applicable, theserial number of the firearm concerned and the description of thedifficulty experienced. It is recommended that shipments beinsured by the owner, since Smith & Wesson® will accept noresponsibility for loss or damage in transit. Transportation andinsurance charges for return to the owner will be paid by Smith &Wesson® if the claim is covered by this warranty.

If the work required is not covered by our “Limited LifetimeWarranty” you will receive a quotation which must be authorized byyou. No actual work will be done without your approval. Returnshipments can be shipped via UPS, FedEx or mail at your cost.Repaired product will be shipped back to you via FedEx requiringan adult signature upon receipt.

UNDER NO CIRCUMSTANCES SHALL SMITH & WESSON® BERESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAM-AGES WITH RESPECT TO ECONOMIC LOSS, INJURY, DEATH ORPROPERTY DAMAGE, WHETHER AS A RESULT OF BREACH OFTHIS WARRANTY, NEGLIGENCE OR OTHERWISE.

Some states do not allow the exclusion or limitation of incidental orconsequential damages, so the above limitation or exclusion maynot apply to you.


36

LIMITED LIFETIME WARRANTY CONTINUED

Smith & Wesson® will not be responsible for:

• Defects or malfunctions resulting from careless handling, unau-thorized adjustments or modifications made or attempted by any-one other than a qualified gunsmith following authorized proce-dures, or failure to follow the instructions in Safety & Instructionmanual that was provided with the firearm from the factory.

• Use of defective or improper ammunition and/or propellant, cor-rosion, neglect, abuse, ordinary wear and tear, or unreasonableuse.

• Use of replacement parts, including but not limited to barrels andsprings, other than factory or authorized parts.

• Criminal misuse, negligence, or use under the influence of drugsor alcohol.

Services that were performed by the Thompson/Center Arms™Custom Shop and/or that are performed by the Smith & Wesson®

Repair Department do not void this warranty. This warranty givesyou specific legal rights, and you may also have other rights whichvary from state to state.

NOTE: All liability is excluded in the event that the instructions pro-vided in the Safety and Instruction manual provided with thefirearm from the factory are not observed.


37

BATTERY WARNINGS WARNING: IF A BATTERY OPERATED ACCESSORY ORATTACHMENT (I.E. LASER, OPTICAL SIGHT OR FLASH-LIGHT, ETC.) IS SUPPLIED OR USED WITH THIS

FIREARM, THE FOLLOWING WARNINGS AND INSTRUCTIONSMUST BE ADHERED TO.

WARNING: KEEP BATTERIES AWAY FROM CHILDREN.THERE IS A CHEMICAL BURN HAZARD ASSOCIATEDWITH BATTERIES.

WARNING: IF A NEW OR USED LITHIUM BUTTON/COINCELL BATTERY IS SWALLOWED OR ENTERS THE BODY,IT CAN CAUSE SEVERE INTERNAL BURNS AND CAN

LEAD TO DEATH IN AS LITTLE AS 2 HOURS. ALWAYS COM-PLETELY SECURE THE BATTERY COMPARTMENT. IF THE BAT-TERY COMPARTMENT DOES NOT CLOSE SECURELY, STOPUSING THE PRODUCT, REMOVE THE BATTERIES, AND KEEP ITAWAY FROM CHILDREN. IF YOU THINK BATTERIES MIGHTHAVE BEEN SWALLOWED OR PLACED INSIDE ANY PART OFTHE BODY, SEEK IMMEDIATE MEDICAL ATTENTION.

• When used correctly, batteries provide a safe and dependablesource of portable power. However, misuse or abuse may result inleakage, fire, or explosion.

• Batteries can explode or leak and cause burns if installed back-wards, disassembled, charged, or exposed to water, fire or hightemperature.

• Always take care to install your batteries correctly observing the“+” and “-” marks on the battery and the device.

• Always replace the whole set of batteries at one time, taking carenot to mix old and new batteries, or batteries of different types.

• Store unused batteries in their original packaging and away frommetal objects that may short-circuit them.

• Remove discharged batteries from equipment promptly to avoidpossible damage from leakage.

• Never dispose of batteries in fire. (Failure to observe this precau-tion may result in an explosion.)

• The batteries are supplied in a charged state and are not designedfor recharging. Recharging may cause leakage, fire, or explosion.

• The batteries should be disposed of properly, including keepingthem away from children.

• Dispose of used batteries immediately. Even used batteries maycause injury.


38

CONTACT AND SHIPPINGINFORMATION

NOTE: A Return Merchandise Authorization (RMA) is the first stepin the process of returning a product in order to receive a repair,replacement or refund.

Please contact the Thompson/Center™ Customer Service Dept.(e-mail: [email protected] or by phone at 800-331-0852 ext. 4125) to obtain authorization to return your firearmso we can process it quickly and efficiently. The RMA numberthat is supplied by Thompson/Center Arms™ must be displayedon the outside of the returned product's packaging; returns with-out an RMA number will be routed differently which will result indelayed processing.

The issuance of a Return Merchandise Authorization (RMA) allowsThompson/Center Arms™ an opportunity to try to diagnose andcorrect a customer's concerns with the product (such as ammuni-tion problems) before it is returned. Accordingly, please contact usbefore returning your Thompson/Center™ firearm.

Shipping Address: Thompson/Center Arms 2100 Roosevelt Avenue Springfield, MA 01104

Should your Thompson/Center™ firearm require service, itshould be returned to the Thompson/Center™ factory.

• Call or e-mail the Customer Service Dept. for authorization andshipping instructions.

• Ensure that the magazine and chamber are unloaded.

• Do not attempt to ship a firearm via US Postal Service; onlyfederally licensed dealers may ship a firearm by US PostalService.

• DO NOT SHIP ANY AMMUNITION.

• Enclose a letter which includes your full name and address(no P.O. Boxes, please), daytime telephone number, e-mailaddress, the serial number of the firearm, and details of the problem experienced (stating the brand and type of ammunitionused when the problem occurred) or work desired.

• Record the serial number before shipping, in case you wish tocheck on the repair status of your firearm.

• Please remove all custom parts and accessories, such as stocks,special sights and scopes, or slings from your firearm beforereturning.


39

CONTACT AND SHIPPING INFORMATION CONTINUED

• Place the firearm in its original case or in a similarly secure con-tainer and pack it securely.

• The package must NOT bear any markings which indicate theidentity of the contents.

• It is most important that you comply with federal, state, and locallaws and regulations. The following guidelines are meant to help,but you must seek assistance from the appropriate authorities ifnecessary.

• If your firearm must be replaced, it may be necessary to ship thereplacement to a dealer rather than directly to you. You may berequested to furnish a signed FFL (Federal Firearms License)from your dealer in such an instance.

• Warranty repair work will begin upon receipt and examination ofthe firearm. In the case of repairs or work not covered by thewarranty, a quotation covering the cost of the work plus shippingcharges will be sent to you. Repairs or modification will bescheduled upon receipt of payment.

WARNING: YOU MAY PURCHASE ACCESSORIES FOR YOUR THOMPSON/CENTER™ FIREARM. YOUMUST HAVE SOME OF THESE PARTS INSTALLED BY A

GUNSMITH QUALIFIED TO PERFORM SERVICE ON THOMP-SON/CENTER™ FIREARMS. NEVER ATTEMPT TO MODIFYYOUR FIREARM OR INSTALL REPLACEMENT PARTS IN YOURFIREARM. ALWAYS USE A QUALIFIED THOMPSON/CENTER™GUNSMITH EVEN IF THE REPAIR SEEMS SIMPLE.

PATENT INFO• This product may be covered by one or more patents.

Visit www.tcarms.com for virtual patent information.


40

ADDRESSES ANDPHONE NUMBERS

T/C Mailing Address: (for questions and comments)Thompson/Center Arms2100 Roosevelt AvenueSpringfield, MA 01104

T/C Shipping Address: (for repairs or warranty work)Thompson/Center Arms ATTN: Repair Department

2100 Roosevelt AvenueSpringfield, MA 01104

T/C Web Address: www.tcarms.com

T/C Customer Service Phone: Toll Free (866) 730-1614

T/C Customer Service E-mail:[email protected]

p/n 3005599 REV:TC_COMPASS_080118


tc compass manual - tc arms...tc_compass_manual_080118_3005599.qxp_tc compass manual 8/13/18 11:57...

Documents