EQUIPMENT MANUAL

(By : Kim Sciandra & Sharon Folds)

EQUIPMENT MANUAL

Table of Contents

3M 1830 Overhead Projector 3

NEC MT1060 Projector 5

Optoma ES522 Projector 8

ACTIVotes 1 3

Promethean 78 ACTIVboard 22

Using 3M 1830 Overhead Projector Before You Begin

The 3M 1830 overhead projector is an easy to use,

sturdy device.

Getting started

1. Plug in power cord. (Assure loose cord is not creating a tripping hazard.)

2. Press the power button.

3. Place material on the Fresnel lens.

4. Focus image by using the focusing knob and adjusting the projection lens.

(Projection lens)

(Focusing knob)

(Release latch) (Fresnel lens)

(Power button)

Changing the bulb

3M PART NUMBER: 78-8011-1186-1 (82V ENX 360W)

1. Unplug the device.

2. Allow the device to completely cool.

3. Press the release latch to open the base.

(Bulb)

(Release lever)

4. (Release lever)Pull the release lever.

5. Gently lift bulb from projector.

6. Gently replace bulb.

a. Assure bulb is well set into the

socket.

b. Move lever forward to secure.

7. Close base.

8. Plug in power cord.

9. Turn on device.

(Gently lift bulb.)

NEC MT1060 Projector - Replace the LampBefore You Begin

Turn the projector off and unplug the power supply.

Wait at least one hour after using the projector before you replace the lamp.

Supplies needed:

Flat head screwdriver

Replacement lamp (Part #MT60LP) OR Optional extended life lamp (Part #MT60LPS)

Step 1 Remove Lamp Cover

There are two grooves located on the

side of the lamp cover.

Push in the two grooves with a

flat head screwdriver.

Gently lift off the cover.

Step 2 Loosen Screws

Loosen the two screws on the lamp unit. Do not remove any other screws.

STEP 3 Remove Lamp Unit

There is a silver handle on the lamp unit.

Pull the handle up to remove the old lamp unit.

STEP 4 Insert New Lamp Unit

Insert the new lamp unit.

Be sure it is pushed all the way in.

STEP 5 Secure with Screws

Secure the new lamp unit with the two screws. Tighten the screws.

STEP 6 Replace Lamp Cover

Slide the lamp cover back on.

Be sure the cover snaps closed

Using Optoma ES522 Digital Projector With Multiple Media DevicesBefore You Begin

The Optoma ES522 is a portable digital projector that

is easy to setup and use.

Connect media devices and follow the directions for

powering on the device.

Assumptions:

Users know how to setup and use peripheral devices.

Control Panel

(Lamp LED) (Zoom / Focus)

(Temp LED)

(Power LED)

(Keystone +)

(Source) (Power)

(Enter / Help)

(AV-Mute)

(Keystone -) (Menu)

(Re-Sync)

Rear View

(Composite Video Input)

(Audio Input L/R) (S-Video Connector)

(VG1/SCART/YPbPr Connector)

(Power)

(Model / Serial Number)

(Mini USB Connector (for remote mouse functions)) (Audio Out 3.5mm Jack)

(RS-232 Connector)

Connecting VCR/DVD Player - Overview

Connecting Magnavox DVD Player/VCR

Model # DV220MW9

(DVD Digital Audio Out)

(VCR Audio In / Video In)

(DVD Audio Out)

(DVD - Component Video Out) (DVD - S Video Out) (DVD/VCR Audio Out / Video Out)

Connecting VCR/DVD Player - Cables

(Cable to speakers (White & Red Cable))

Connecting Laptop - Overview

(Video Output )

(Audio Output)

Connecting Laptop - Cabling

Video

(Laptop Video Output)

Audio

(Laptop Audio Output)

(SPEAKERS)

Powering on the Projector

1. Remove the lens cover of the projector.

2. Connect the power cord to the projector.

3. Connect the media device.

4. Turn on the media devices.

5. Verify the Power LED is flashing, press the power button.

6. If a PC is being used, assure the PC is setup for output to the projector.

7. If more than one device is being used, press the Source to toggle between the devices.

8. To focus the image, adjust the zoom/focus dial found on top of the projector.

9. To adjust the height of the image, press the elevator button found in front of the device.

Powering off the Projector

1. Press Power to turn off the projector.

2. A message will appear. Press Power a second time.

3. The cooling fans will continue to run for a short period of time.

** WARNING ** Do not turn on the projector immediately following a power off procedure.

Using ACTIVotes with ActivInspire Quick Start GuideBefore You Begin

Make sure the Voting Browser icon is in your toolbox.

View Customize

In the All Commands box, choose the Voting Browser.

Click the Add>> button to move the command to the Main Toolbox.

Create User Databases

The following instructions will help you set up your database of students and save the database.

1. Add Class

Edit Student DatabaseAdd Class. Fill in the pop-up box and click Submit.

2. Add Students

Click on the Add Student button. Fill in the pop-up box and click Submit.

Continue using the Add Student button to enter remaining students.

3. Assign Students to Class

Highlight student names

Click the Left Arrow button (