t460hw02 v1 product spec - novitronic.de s286hw66 v0 b… · s286hw66 v0 6/24 4. general...
TRANSCRIPT
S286HW66 V0 1/24
Product Description:
S286HW66 V0 28.6" Flat Panel Display Product (Without Tuner)
DARWIN Model Name: S286HW66 V0
Customer Part No. / Project Name:
Darwin
Approved by:RD Head Reviewed by:Project Member
PM:CJ.Chnag
EE:John Hsiao
ME:Gabriel Chiang
Packing:Edward.Huang
OM:Leo.Hsieh
OPT : CH.Wu
Power:JC.Yang
EMI:Neil.CH.Tsai
Safety:Kite JW Huang
PA:Young.Wu
Reviewed by:HW Manager
Reviewed by:OM Manager
Reviewed by:PA Manager
Reviewed by:PSU Manager
Reviewed by:SW Manager Prepared by:Project Leader
John.Hou
Note
S286HW66 V0 2/24
Document Version: 0.1
Date: 2017/08/25
Product Specification Sheet
S286HW66 V0 28.6" Flat Panel Display Product
Model Name: S286HW66 V0
DARWIN P/N: 99.28S04.0AT-BT3
(*) Preliminary Specification
() Final Specification
S286HW66 V0 3/24
Contents
No
Contents
Record of Revision
1 Application Range
2 Operational Specification
3 Test Method
4 General Specification
5 Features and Functions
6 Safety and Regulation
7 Video
8 Optical Performance
9 Audio
10 Input Support Timing
11 Power
12 Other specification
12.1 The others
12.2 Reliability
12.3 LED indicator & power consumption
12.4 Power Sequence
13 Mechanical Specification
14 Accessory
S286HW66 V0 4/24
Record of Revision
Version Data Page. Old Description New Description Remark
0.0 2017/08/25 -- ---
S286HW66 V0 5/24
1. Application Range
1.1. This specification sheet is applied to all of the Public Information Display with ODM by Darwin Corporation.
1.2. Not-included specification and each product spec in this spec sheet apply correspondingly to the following each
country standard and requirement of Buyer
Model Name Customer Marketplace Panel Chassis Remark
S286HW66 V0 GA Taiwan G286HAN01.0 Metal NCT
2. Operational Specification
Each part is tested as below without special appointment.
2.1 Temperature:
-Operating 0℃ ~ 40℃
-Non-operating -20℃ to +60℃
2.2 Relative Humidity:
-Operating 10 to 90%
-Non-operating ≦ 90%
2.3 Power Voltage: Standard input voltage (AC100V~ 240V 50/60Hz)
* Standard Voltage of each product is marked by models
2.4 Specification and performance of each parts are followed each drawing and specification by part number in
accordance with BOM.
2.5 The receiver must be operated for about 20 minutes prior to the adjustment.
3. Test Method
3.1 Performance: Display test-method follows Darwin Public Information Display test items or Customer’s spec
3.2 Demanded other specification
Safety: BSMI specification
EMC: BSMI specification
Model Market Appliance Compliance
S286HW66 V0 Taiwan
Safety: BSMI
EMC: BSMI
GP:BSMI
Safety: CNS14336-1
EMC: CNS13438
GP:符合 CNS 15663 第 5 節「含有標示」
S286HW66 V0 6/24
4. General specification
No Item Specification Remark
1 Receiving System NA
2 Available Channel NA
3 Input Voltage AC 100V~240V 50/60Hz
4 Market Taiwan
5 Screen Size 28.6 inch 1/2 FHD 60hz G286HAN01.0
6 Aspect Ratio 16:4.5
7 Tuning System NA
8 LCD Module G286HAN01.0
9 Operating Environment 1) Temp : -0 ~ 40 ℃
2) Humidity : 10 ~ 90 %
10 Non-Operating
Environment
1) Temp : -20 ~ 60℃
2) Humidity : ≦ 90 %
5. Features and functions
No Item EA Specification Remark
1 Terminals
DC power input 1 DC 12V Power Input(2.5ψ) Side (2.5Φ)
Audio input 1 PC Audio in Side (3.5Φ Jack type)
RGB Input 1 Analog PC In(DSUB-15F) Side
RS232 input 1 RS232/UART input control(DSUB9-F) Side
HDMI input 1 HDMI Side
USB 1 Media & FW upgrade Side
Local Key POWER, INPUT, MENU, VOLUME(+, -), Select (▲ , ▼) Rear (7Key)
LED Indicator On : Green ; Standby : Red Rear/ 2 Colors
IR Receiver Infrared Receiver , 37.9KHz Rear
2 RCU Key
POWER Power ON/OFF
INPUT Input Signal Select
1 DIGI Key 1 No Function
2 DIGI Key 2 No Function
3 DIGI Key 3 No Function
4 DIGI Key 4 No Function
5 DIGI Key 5 No Function
6 DIGI Key 6 No Function
7 DIGI Key 7 No Function
8 DIGI Key 8 No Function
9 DIGI Key 9 No Function
RECALL Recall No Function
S286HW66 V0 7/24
0 DIGI Key 0 No Function
ENTER Enter Key No Function
PICTURE Selects a preset picture mode
Music Selects a preset sound mode for audio output.
Aspect Selects an image aspect ratio for the displa
FREEZE No function
Volume up Adjust audio volume
Volume down Adjust audio volume
INFOR
MUTE Mute or un-mute audio ouput
Channel up No function
Channel down No function
FAV No function
SLEEP
Surround Sound No function
SOUND TYPE No function
▲ Select Up
▼ Select Down
> Select Right & value +
< Select Light & value +
OK Enter key
MENU Display the menu
BACK
RED No function
GREEN De-select items for
multi-media
YELLOW No function
BLUE No function
SUBTITLE No function
Pause For USB
Stop For USB
Play For USB
Previous For USB
Next For USB
backward For USB
forward For USB
Remote controller (49.42S33.001)
S286HW66 V0 8/24
User Main Menu function
S286HW66 V0 9/24
Layer 1 Layer 2 Layer 3 Layer 4 Default Value
AV Component Hdmi1 Hdmi2 DVI VGA USB
Picture
影像
Picture Mode
影像模式
圖像模式
Standard/Dynami
c/Advertiser/Cust
om
標準/動態/廣告
客戶/用戶
Dynamic Dynamic Dynamic Dynamic Dynamic Dynamic Dynamic
Contrast
對比
0~100
0~100 73 73 73 73 73 73 73
Brightness
亮度
0~100
0~100 50 50 50 50 50 50 50
Sharpness
銳利度
0~10
0~10 6 6 6 6 6 6 6
Tint
色調
Tint
色調
0~50
0~50 26 26 26 26 26 26 26
Red Hue -16~16 0 0 0 0 0 0 0
Magenta Hue -16~16 0 0 0 0 0 0 0
Blue Hue -16~16 0 0 0 0 0 0 0
Cyan Hue -16~16 0 0 0 0 0 0 0
Green Hue -16~16 0 0 0 0 0 0 0
Yellow Hue -16~16 0 0 0 0 0 0 0
Color
色濃度
Color
色濃度
0~50
0~50 47 47 47 47 47 47 47
Red Saturation 0~15 0 0 0 0 0 0 0
Magenta
Saturation 0~15 0 0 0 0 0 0 0
Blue
Saturation 0~15 0 0 0 0 0 0 0
Cyan
Saturation 0~15 0 0 0 0 0 0 0
Green
Saturation 0~15 0 0 0 0 0 0 0
Yellow
Saturation 0~15 0 0 0 0 0 0 0
Backlight
背光控制
0~100
0~100 100 100 100 100 100 100 100
S286HW66 V0 10/24
Color Temperature
色温
Color
Temperature
色温
4900/6500/9300/11
500/ Custom
4900/6500/9300/11
500/ 用戶
13000K 13000K 13000K 13000K 13000K 13000K 13000K
Red Gain
紅色增益 0~2047
13000K default RGB = (988, 1060, 1115) Green Gain
綠色增益 0~2047
Blue Gain
藍色增益 0~2047
Gamma
伽瑪
2.2/ 2.4 /
Native.
2.2 2.2 2.2 2.2 2.2 2.2 2.2
Aspect
Ratio
畫面比
例
Auto/Normal/
Wide/ /Dot by
Dot
自動/標準/寬
螢幕/點對點
Set the aspect ratio of the current.
The item is gray out when the zoom (in multi-display) is
enable.
The option as below:
a. AV source : the option is 4:3, 16:9, zoom, cinema and
dot by dot.
b. Media source: In movie, if overscan is Auto, the option
is 4:3, 16:9, zoom, dot by dot. If overscan is OFF, option is
4:3 , 16:9 and dot by dot.
c. other source : If overscan is Auto, option is 4:3, 16:9,
zoom, cinema, dot by dot. If overscan is OFF, option is
4:3 , 16:9 and dot by dot.
If multi-display is active, aspect ration will change to 16:9
and gray overscan item, set overscan as OFF.
(refer to the sheet of Aspect Ratio Setting)
VGA setting
VGA 設定
H position
水平位置 0~100
Gray out
50
Gray
out
V position
垂直位置 0~68
36
50 Clock
頻率 0~100
Phase
位相 0~100 60
Auto Adjustment
自動調整
Enable/Disable
有効//無効 Enable
Auto None
S286HW66 V0 11/24
自動
Reset Picture Setting
重設影像設定 None
Sound
声音
Sound Mode
声音模式
Sound Style
声音模式
Standard/Dynamic/
Custom
標準/動態/用戶
Dynamic Dynamic Dynamic Dynamic Dynamic Dynamic Dynamic
Treble
高音 50~+50 10 10 10 10 10 10 10
Bass
低音 50~+50 30 30 30 30 30 30 30
Balance
平衡 50~+50 0 0 0 0 0 0 0
Surround
Sound
環繞音效
On/Off
開啟/關閉 OFF OFF OFF OFF OFF OFF OFF
Reset Sound Setting
重設聲音設定 None
Setup
設定
Power Save
省電模式 Off, 30sec~300sec/30sec steps
300sec
(Set the timer to power off monitor when current source
has no signal.)
Software
Update(USB)
軟體更新
(USB)
None
(Update the FW by USB.
The confirm OSD has YES or NO item.
Yes : update the FW.
No : exit the confirm OSD.)
Restore Default
恢復出廠設置
None
(Restore the default value.)
Initial
Setting
快速設定
Menu
Language
菜單語言
English/ /簡体中文 English
Remote
Operation 遙
控器操作
Enable/Disable
啟用/關閉
Enable
(In IR lock mode, user can use keypad to enter "Remote
Operation" item to unlock IR.
In keypad lock mode, user can use IR to enter "keypad
operation" item to unlock keypad.
If IR and keypad both are in lock mode, please press
S286HW66 V0 12/24
Menu+Left+Right+Up+Down to unlock.)
Keypad
Operation
按鍵操作
Enable/Disable
啟用/關閉
Enable
(In IR lock mode, user can use keypad to enter "Remote
Operation" item to unlock IR.
In keypad lock mode, user can use IR to enter "keypad
operation" item to unlock keypad.
If IR and keypad both are in lock mode, please press
Menu+Left+Right+Up+Down to unlock.)
Anti-Image
Retention
影像殘留保
護
Off/picture shift
關閉/畫面平移
OFF
(Off: No image retention behavior.
White pixel: Show/hide 4x4 pixel per 1.2 second.
Picture Shift: Shift 2 pixel per 1 min. The shift behavior is
"left -> up-> right -> down -> center".)
System
Information
系統資訊
Model Name
型號 S286HW66 V0
SW Version
軟體版本 TBD Wait G/L FW version
S286HW66 V0 13/24
6. Safety and Regulation
No Item Min Typ Max Unit Remark
1 Force Stability – Incline Plane Tip Test 10 deg 不適用,本機需搭配 wall
mount 使用
2
Isolation Gap, AC-AC Primary-GND
420Vpeak
(clearance) 2.0 mm
1.Safety distance for components with 2N force for judgment. 2.Pollution degrees 2
3.Reference the IEC60950-1
3
Isolation Gap, Primary-Secondary
420Vpeak (clearance) 4.0 mm
4
Isolation Gap, Primary ↔ GND
320Vrms(Cree page)
3.2 mm
400Vrms(Cree page)
4.0 mm
Isolation Gap, Primary ↔ Secondary
320Vrms(Cree page)
6.4 mm
400Vrms(Cree page)
8.0 mm
5 Power Consumption, Max 45 W
Power Consumption, Stand by 0.5 W
6 Dielectric Voltage
Class I Primary-PG: 1500 Vac/ min at 10mA 2120 Vdc/ min at 10mA (Eng+MP)
PG = Protective Ground Eng = Engineering stage
MP = Mass Production
*If set use extra adaptor(Class III), no need
this routine test.
Class II
Primary- Secondary: 3000 Vac/min at 10mA 4240 Vdc/ min at 10mA
(Eng+MP)
Test time Eng- 1min MP-3sec
7 Isolation Resistance 2 ㏁
1. Primary to GND/PG 2. L/N polarity directly
connected to the mains
4 ㏁ Primary to Secondary
8 Leakage Current
to Accessible parts and circuits not connected to
protective earth b
< 0.25 mA Measuring network
described in IEC 60990 Annex D to Equipment main
protective earthing terminal
<3.5 mA
9 Sharp Edge NA
10 Compliance Safety CNS14336-1
EMC CNS13438
11 Earth Continuity Test ≤0.1Ώ at 32A / 120s Class II、III 機種不需測試
12 Wall mount three times the weight of the equipment
but not less than 50 N. /1min
7. Video
7.1. General Specification
Designed by Customer
S286HW66 V0 14/24
No Item Min Typ Max Unit Remark
1 Over scan, Vertical % NA
2 Over scan, Horizontal % NA
3 Over scan, Vertical 2 - 5 % Video
4 Over scan, Horizontal 2 - 5 % Video
5 Max Input Level dBm NA
6 Gain Limited Sensitivity VHF - dBm NA
UHF - dBm NA
7 IF Rejection Ratio dB NA
8 Image Rejection Ratio dB NA
9 Adjacent CH Rejection Ratio Upper dB NA
Lower dB NA
10 FM Rejection Ratio 201CH dB NA
203CH dB NA
11 Sync Stability Level % NA
Range dBm NA
12 Tuning Range MHz NA
13 Color Killer Sensitivity dBm NA
14 Component Video Input Level (Y, CB/PB, CR/PR) 0.6 0.7 0.8 Vpp 75 ohm without Sync
15 PC RGB Video Input Level 0.6 0.7 0.8 Vpp 75 ohm without Sync
16 PC H/V Input Level 5 TTL Level
17 Composite Video Input Level (CVBS, S-Video) 0.6 0.7 0.8 Vpp 75 ohm without Sync
7.2. Picture Quality
The following faulty symptoms should not be recognized for all the signal inputs with commercial DVD player, and related
equipment source.
S286HW66 V0 15/24
No Signal Symptoms Remark
1 40 IRE ~ 100IRE -Noise, Beat
White Raster Pattern -Flicker
2
Cross Hatch Pattern -Ring
SMPTE Pattern -Over Shoot
Mono Scope -Smear
-V-jitter, H-jitter
3 Color Bar
-Color Distortion
-Noise, Beat
-Color Tangent
4 Gray Scale -Noise, Beat
-Gamma Distortion
5 Input/Channel Change
-Unstable Picture
Noise(Picture Garbage)
-Screen Flashing
8. Optical Performance (Remark: Picture mode is in “Vivid”)
1) G286HAN01
No Item Min Typ Max Unit Remark
1 White peak brightness(Center) 800 1000 cd/m² Module specification *(1
2 Contrast ratio(Center) 800 1000 Module specification*(2
S286HW66 V0 16/24
No Item Min Typ Max Unit Remark
3 DCR (Dynamic Contrast Ratio) NA Dimming range 20%~100%
4 Brightness uniformity(9P) 75% 80% Refer to LCD Specification*(3
5
Color coordinate
White X
-0.05
0.313
+0.05
Module specification*(1
6 Y 0.329
7 Red
X 0.64
8 Y 0.345
9 Green
X 0.324
10 Y 0.627
11 Blue
X 0.152
12 Y 0.057
13 Viewing angle 75 (R/L)
75(U/D)
89(R/L)
89(U/D) degree R/L, U/D,Contrast Ratio>10*(4
15 Gamut CG θ=ψ=0 72% --- % Refer Module Specification
16 Gamma γ VESA 2.0 2.2 2.4 --- Refer Module Specification
[Note] Definition of these measurement items is as follows:
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark
environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle
of φ and θ equal to 0°.
1) presents additional information concerning the measurement equipment and method.
2) Definition of Contrast Ratio
CR=ON (White) Luminance/OFF (Black) Luminance
3) Definition of Luminance and Luminance uniformity
Central luminance: The white luminance is measured at the center position “5” on the screen,
see Fig.1 below. And the measure time is 40 min after discharged.
9P Luminance (AVG): The white luminance is measured at measuring points 1 to 9, see Fig.1
below.
9P Uniformity: L = (LMIN /LMAX) ×100%
SR3 or equivalent
S286HW66 V0 17/24
4) Definition of Response Time:
9. Audio
9.1. General specification
Speaker Output :
Item Specifications Remark
S286HW66 V0 18/24
Audio Amplifier Output (6 Load)
Maximum Audio Output 2.0 W of each channel @0.5Vrms, 1KHz tone, THD < 10%
THD+N vs Power 10% @ 0 ~ 0.5 Vrms, 1 KHz tone PC input:0 ~ 1Vrms
THD+N vs Frequency 1% @ 70% Max power, 40 Hz ~ 15 KHz
L/R Channel Crosstalk -55 dB @ 70% Max power, 40 Hz ~ 15 KHz
Input Channel Separation -55 dB @ Max power, 40 ~ 15 KHz
S/N 65 dB @ 70% Max power, 40 Hz ~ 15 KHz
Frequency Response 3 dB @ 70% Max power, 40 Hz ~ 15 KHz
Treble Enhancement +2/-7 dB @ 70% Max power, 2K Hz ~ 15 KHz
Bass Enhancement +2/-7 dB @ 70% Max power, 40 Hz ~ 200 Hz
Noise Frequency Scan (no signal) -70 dDWP @ 20 Hz ~ 1 KHz
-80 dDWP @ 1 KHz ~ 20 KHz
Noise Frequency Scan (no cable) -60 dDWP @ 20 Hz ~ 1 KHz
-70 dDWP @ 1 KHz ~ 20 KHz
Dynamic Range 60 dB @ 80% Max power, 20 Hz ~ 20 KHz
Acoustic Noise 25 dBA @ 20 Hz ~ 20 KHz
Speaker Output
Sound Pressure Level (SPL) 80 3 dB @ 1m/1W input, 600/800/1000/1200 Hz average
Resonance Frequency, Fo 200 Hz 20% @ 1Vrms input CLIO
Frequency Response -10 dB @ 1m/1W input, Fo ~ 15KHz
10. Input Support Timing :
10.1 RGB Input (PC)
1) S286HW66 V0
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Remark Proposed
1 1920x1080 67.50 60.00 148.50 Full HD ○
2 1920x540 67.50 60.00 148.50 Full HD ○
Note:
1. D-sub 不支援 SOG 同步
2. D-sub 不支援 Interlaced 訊號
10.2 HDMI /DVI Input (PC/Video)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Remark Proposed
PC for S286HW66 V0
1 1920x1080 67.5 60 148.5 Full HD X
2 1920x540 67.5 60 148.5 Full HD X
Video
1 1280*720 45.00 60P 74.25 976/PG1 HDTV 720P
2 1280*720 37.75 50P 74.25 942/PG2 HDTV 720P/50Hz
3 1920x1080 33.75 60i 74.25 972/PG1 HDTV 1080I
4 1920x1080 28.13 50i 74.25 939/PG2 HDTV 1080I/50Hz
S286HW66 V0 19/24
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Remark Proposed
5 1920x1080 67.5 60P 148.5 970/PG1 HDTV 1080P/60Hz
6 1920x1080 56.25 50P 148.5 937/PG2 HDTV 1080P
7 1920x1080 27 24 74.25 579/PG2 HDTV 1080P/24Hz
8 1920x1080 28.13 25 74.25 578/PG2 HDTV 1080P/25Hz
9 1920x1080 33.75 30 74.25 576/PG2 HDTV 1080P/30Hz
11. Power
11.1. General specification
N
o
Item Min Typ Max Unit Remark
1 AC Power Voltage 100V 110V 240V V
2 Max. Input Current (S286HW43 V0) 1.1A Arms Based on AC 90V
3 Standby Power - - <1W W
11.2.1 Control Signal (S286HW66 V0)
N
o
Item Min Typ Max Unit Remark
1 PWR on/off
control V ON/OFF
On=High 2.5 3.3 5.5 V
Off=Low 0 0.7 V
2 Back light on/off
control V ON/OFF
On=High 2 3.3 5.5 V
Off=Low -0.3 0.8 V
3 External PWM
dimming
Duty 10 100 %
Frequency 90 180 240 Hz
High Level 2 3.3 V
Low Level 0 0.8 V
12. Other specifications
12.1 The others
No Item Min Typ Max Unit Remark
1 Soft Ware Functionality Test --- --- --- ---
Customer’s spec/
Darwin Generic
Specification
2 REMOCON Working Sensitivity, Straight --- --- 8 m Rear Side
3 REMOCON Working Sensitivity, L/R --- --- 6 m 30 degree / Rear Side
4 Search Sensitivity --- TBD --- dBm
S286HW66 V0 20/24
No Item Min Typ Max Unit Remark
5 Power ON Screen Mute Time --- TBD --- sec
6 EE Acoustic
Noise
Normal mode NA dBA 3 direction(front, rear, up),
distance 40cm Power Saving mode NA dBA
7 ME Acoustic
Noise
Max level-55dB or less in 10
minutes NA dB
Distance 100cm
background noise < 40
dBA
8 Sound
Vibration
TV settings: Standard position
except volume =70%
listening position:
- Angle: -60° ~ +60°
- Distance: 100cm
--- --- --- --- no vibration, rattle noise
and mechanical resonance
12.2 Reliability
No Item Min Typ Max Unit Remark
1 ESD(EN61000-4-2) NA NA kV 非 BSMI 強制
2 EFT/Burst (EN61000-4-4) NA NA kV 非 BSMI 強制
3 Surge Immunity (EN61000-4-5) NA NA kV 非 BSMI 強制
4 Voltage Dip Test, 10ms (EN61000-4-11) NA NA % 非 BSMI 強制
5 Voltage Dip Test, 500ms(EN61000-4-11) NA NA % 非 BSMI 強制
6 CST(EN61000-4-6) NA NA % 非 BSMI 強制
7 EMI Test -1 -3 dBuv DWP or Customer’s spec
8 Harmonic Current Test (EN61000-3-2) NA NA % DWP or Customer’s spec
9 Voltage Flicker Test (EN61000-3-3) NA NA % DWP or Customer’s spec
10 Open & Short Abnormal Test DWP or Customer’s spec
11 Operation Temperature 0 25 40 deg DWP or Customer’s spec
12 Operation Humidity 10 90 % DWP or Customer’s spec
13 Storage Temperature -20 60 deg DWP or Customer’s spec
14 Cold/Hot Start Test -10 40 C DWP or Customer’s spec
15 Thermal Profile Test 25 40 C DWP or Customer’s spec
16 Condensation Test -20 C DWP or Customer’s spec
17 Thermal Shock Test (PCBA Board) -40 125 C Power BD Only
18 Transportation Test NA NA
19 Overstress Test NA NA
20 Durability Test NA NA
21 Life Test 50,000 hrs DWP or Customer’s spec
22
Yield Rate
85% Engineering Pilot-Run
90% Production Pilot-Run
95% 1st Mass Production
S286HW66 V0 21/24
12.3 LED indicator & power consumption
No Item Min Typ Max Unit LED status Remark
1 Stand by power --- 0.7 1 W Red Color At AC 110V
2 DPMS --- --- 0.5 W Red Color PC Signal Lose with
OSD
3 Normal Operation (S286HW43 V0) TBD W Green Color At AC 110V
12.4 Power Sequence
12.4.1. Power on & Power off
a) S286HW66 V0
TBD
S286HW66 V0 22/24
12.4.2. Power sequence for Panel
a) G286HAN01.0
S286HW66 V0 23/24
13. Mechanical Specification
13.1. General Specification
b) S286HW66 V0
Six Side Drawing
No
Item Content Remark
1 Product
Dimension
Width Length Height Unit
Before Packing 233.9 735.9 45.4 mm
After Packing 357 832 143 mm
Only Set 5 Kg
With BOX 7 Kg
3 Container
Loading
Quantity
Individual or
Palletizing
20 ft 40 ft 40ft(HQ)
TBD TBD TBD
5 Appearance General
Front Cover : Black Texture
Back Cover : Black Texture
Handle : TBD
S286HW66 V0 24/24
13.2 Mechanical specification for GAP
a) S286HW66 V0
No Item Standard
Remark Min Typ max unit
1
Cell + bezel GAP 0.5 1.0 1.8 mm
Bezel + rear cover GAP 0.0 0.2 1.0 mm
14. Accessory
TBD