swiss dt swiss gt swiss st ct 20 machine options · 2019-10-22 · swiss gt 32 swiss gt 26 swiss gt...
TRANSCRIPT
Machine options
Swiss DTSwiss GT
CT 20
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-0040 248-0040
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-0210
Options Machine2
Positioning B axis mounted on the rear platen X1 / Y1. Setting angle from 0° to 135°. Max. RPM : 9,000. Motor - Tools ratio 1:1,5 Power 1 KW with 1 drive module for Axial machining along with 3 spindles with ESX16 collet in main operation and ESX12 collet in counter-operation (supplied without collet).1 Plate for 3 turning tools for rear platen. Tool section 16x16 mm. Tool block for end work with 3 bores 22 mm (used only with with option 0001) – (Ex works)
B axis option
Guide bush holder for non-revolving, adjustable, drawn guide bushes collet including lubricating device. Max. capacity diam. 13 mm, collet o.d. 18 mm
Machine options
Description
386267
2020332
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-0942 257-0942
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-0942 248-0942
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-4042 257-4042
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4042 248-4042 258-4042
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-0960 258-0960
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-0943
256-4043
3Options Machine
Description
Adaptation for a F13 (76-357) collet Ø 10 mmMain spindle
Counter spindle
Counter spindle
Adaptation for a F25 (76-64) collet Max Ø 20 mmMain spindle
Set of reduction tubes for main spindle (internal diameter 8,14,17)
Adaptation for a F10 (76-86) collet Ø 7 mm
390235
306029
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-0961 258-0961
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-0960
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1010 248-1010 258-1010
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-1010
Options Machine4
Machine options
Description
Set of reduction tubes for main spindle (internal diameter 8, 14, 17)
Set of reduction tubes for main spindle (internal diameter 8, 14)
Plate for 5 turning tools for front platen. Tool section 16x16 mm
Plate for 5 turning tools for front platen. Tool section 12x12 mm
398530
386209
398577
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-1010
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-1012
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1012 248-1012
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1014 248-1014
5Options Machine
Description
Plate for 9 tools (section 8x8)
Plate for 3 turning tools for rear platen. Tool section 12x12 mm
Plate for 4 turning tools for rear platen. Tool section 16x16 mm
Plate for 3 turning tools for rear platen. Tool section 16x16 mm
B axis option
2020313
398585
398547
418718
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
258-1210
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1210 248-1210 256-1210
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-1211
Options Machine6
Machine options
Description
Tool block with 4 bores Ø 22 mm for steady end working tools
Tool block for end work with 5 bores Ø 22 mm with possibility to work simultaneously in main and counter operation.
Tool block for end work with 5 bores 22 mm diameter with possibility to work simultaneously in main and counter operations.
386218
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1230 248-1230 256-1230 258-1230 257-1230
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1235 248-1235 256-1235 258-1235 257-1235
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1236
7Options Machine
Description
Collet holder extension, simple type with 22 mm Ø shank and 70 mm long for ER16 collet (supplied without collet) (used with front unit and/or 4130)
Double collet holder extension with a Ø 22 mm and 110 mm long for ER 16 collet, used in the main and / or counter operation (supplied without collet) (used with 1210 and/or 2005 and/or 2010 and/or 2015 and/or 2020 and/or 4130)
Double collet holder extension with a Ø 32 mm and 110 mm long for ER20 collet, used in the main and / or counter-operation (supplied without collet)
2020074
2020075
398530
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-1500
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1620 248-1620 256-1620 258-1620
258-4600 257-4600 247-4600
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1622 248-1622 258-1622
Options Machine8
Machine options
Description
S11 modular motor(Used with 1630/1700/1750)(Ex works)
Rotating drilling/milling attachment with a spindle for ESX20 collet. Low type (supplied without collet) Max. clamping dia: 13 mm.
Rotating drilling/milling attachment with a spindle for ESX20 collet. Low type (supplied without collet) Max clamping diameter: 13 mm
Emulsion compatible
398563
398537
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1630 248-1630 256-1630 258-1630
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1632 248-1632 256-1632 258-1632
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1640 248-1640 256-1640 258-1640
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1642 248-1642 256-1642 258-1642
9Options Machine
Description
Rotating drilling/milling attachment with a spindle for ESX20 collet. High type. (supplied without collet)Max clamping dia : 13 mm.
Rotating drilling/milling attachment with a spindle for ESX20 collet. High type. (supplied without collet)Max clamping dia : 13 mm.
Rotating milling / slotting attachment with a spindle for ESX 20 collet. Max saw Ø 63 mm. (supplied without collet)
Rotating milling / slotting attachment with a spindle for ESX 20 collet. Max saw Ø 63 mm. (supplied without collet)
Emulsion compatible
Emulsion compatible
398539
398539
398561
398561
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-1630
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1650 248-1650 256-1650 258-1650
258-4650 257-4650
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1652 248-1652 256-1652 258-1652
Options Machine10
Machine options
Description
Drilling/milling device for disc-type cutter Ø 40 mm max.(1500 required)
Rotating drilling / milling attachment with a right angle head that can positioned angularly from 0 to 90°. Spindle with a collet for ESX 12 (supplied without collet)
Rotating drilling / milling attachment with a right angle head that can positioned angularly from 0 to 90°. Spindle with a collet for ESX 12 (supplied without collet)
* 0° only
Emulsion compatible
*
2020321
398578
398578
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1660 248-1660 256-1660 258-1660
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1662 248-1662 256-1662 258-1662
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1665 248-1665 256-1665 258-1665
11Options Machine
Description
Double, axial drilling attachment with spindle for ER 11 on the main operation (supplied without collet)
Base for double Axial drilling/milling on the main operation Uses 1 position (requires 1667 and/or 1677)
Additional double axial drilling. Mounts on option 1660 (max. 1) with spindle for ER 11 (supplied without collet)
Emulsion compatible
386204
386204
386222
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1672 248-1672
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1677 248-1677 258-1677
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1667 248-1667 256-1667 258-1667
Options Machine12
Machine options
Description
Base for an adjustable 0 to 90° angle double drilling / milling attachment. Mounts on rear side of platen (max. 1). Takes up 2 positions. (requires option 1667 and/or 1677)
Double Axial Milling/Drilling Module with spindles for ER16/ER11 collet on the main operation (max. 2)(Max machining depth : 30 mm) – (Max cutter diameter : 10 mm)(requires option 1662 and/or 1672) – (supplied without collet)
Emulsion compatible
Emulsion compatible
Double Module Axial drilling/milling on the main operation (max. 2) with spindle for ER 11 (requires option 1662 and/or 1672) (supplied without collet) – (Compatible with emulsion)
Emulsion compatible
390241
390242
386222
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1700 248-1700 256-1700 258-1700
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-1700
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-1700
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1710 248-1710 256-1710 258-1710
13Options Machine
Description
Polygon attachment, radial type. Max RPM : 5,000Takes up 3 positions and mounts on the upper positions of the rear side of platen (oilmist extractor is recommended)
Polygon attachment, radial type. Max RPM : 5,000Takes up 3 positions and mounts on the main operation(oilmist extractor is recommended)
Polygon attachment, radial type. Max RPM : 3’750Takes up 2 positions and mounts on the upper positions of the rear side of platen (oilmist extractor is recommended)
Insert type polygon cutter, OD : 80 mm. Bore Ø: 16 mm
398542
2020320
2020074
595973
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-1710
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-1750
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1750 248-1750 256-1750 258-1750
Options Machine14
Machine options
Description
Insert type polygon cutter, OD : 80 mm. Bore Ø: 16 mm (inserts are not included)
Gear hobbing device. Angle ± 2°. Milling width 6 mm Supplied with one set of shims (2-3-4 mm) and two chucks (Ø 3.5 and 4.5 mm) – (1500 required)
Generating milling attachment for gears with length profileAngular adjustment +/- 15 degreesMax. rotation speed 6000 RPMMax. diameter of milling cutter 32 mm, width 30 mmMaximum module 1Quality level max. : ISO 8
2020074
2020319
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1800 248-1800 256-1800 258-1800 257-1800
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1810 248-1810 256-1810
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1815 248-1815 256-1815 258-1815
15Options Machine
Description
High frequency spindle Ø 22 mm, 60,000 rpm with a 9 poles plug for light axial work in MOP.Supplied with the following accessories :1 ER 8-UP collet, max. capacity Ø 3 mm1 tightening nut ER 8-MS1 wrench E 8-MS1 wrench SW 9(requires 1815 and/or 1825, 1830 et 1835)
High frequency spindle Ø 25 mm, 60,000 rpm with 9 poles plugfor light axial and/or tranversal work in MOP from end attach-ment and in COP. Supplied with the following accessories :1 ER 8-UP collet, max. capacity Ø 3 mm 1 tightening nut ER 8-MS 1 wrench E 8-MS 1 wrench SW 9 (requires 1820, 1830 and 1835)
HF support, bore Ø 22 mm for 1 position for axial mounting in MOP (used with 1800 option)
307180
307180
307249
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1820 248-1820 256-1820
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1825 248-1825 256-1825 258-1825 257-1825
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1830 248-1830 256-1830 258-1830 257-1830
Options Machine16
Machine options
Description
HF support, bore Ø 25 mm for 1 position for radial mounting in OP and axial in COP (used with 1810 option)
HF support, bore Ø 22 mm for 1 position for radial mounting in OP and axial in COP (used with 1800 option)
Frequency converter for Ø 22 mm and/or Ø 25 mm HF spindle with 9 poles plug (used with 1800 and/or 1810)
386212
386214
227666
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1838 248-1838
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-1835 256-1835 258-1835 257-1835
548-1837 248-1837
17Options Machine
Description
HF spindle Ø 22 and/or Ø 25 adaptation Including : Air conditioning unit with support and pneumatic connections and electrical connecting wiring (used with 1800 and/or 1810) - (max. 1 per machine) (possible only with 0001)
HF spindle Ø 22 and/or Ø 25 adaptation. Including : Air con-ditioning unit with support and pneumatic connections and electrical connecting wiring (max. 1 per machine)
386214
390244
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1900 248-1900 256-1900 258-1900
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-1915
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-1900
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1910 248-1910 256-1910 258-1910
Options Machine18
Machine options
Description
External thread whirling attachment with high speed rotation of the tools with inclination of + / - 15°. Attachment takes up 3 positions. Mounts on high positions of platen 1 requires options 1910 and / or 1920
Thread whirling head for constant profile cutters. Includes setting gage. For bar up to Ø 10 mm (cutters not included)(used only with with option 1900)
External thread whirling attachment. Max angle positioning : +/- 15°. Takes up 2 positions in OpAssembly recommended in position T130/T140(it Cancel position T362, T363 and T364 on front-end tools support block) - (requires option 1910 and/or 1915 and 1920)(oilmist extractor recommended)
Thread whirling head till 10 mm + centering gage
398541
2023031
246795
472088
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-1920 248-1920 256-1920 258-1920 247-1920
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-1950 256-1950
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-1960 256-1960
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-1970 256-1970
19Options Machine
Description
Sharpening device for thread whirling cutters
External thread whirling attachmentMax angle positioning : +/- 25°Takes up 3 positions and mounts on the upper positions of the rear side of platen (requires option 1960 and 1970)(oilmist extractor and high pressure pump (20 bar) recom-mended)
Thread whirling head for constant profile cutters Ø 12 mm. Includes setting gage for bar up to Ø 5 mm(Inclination possible only up to 15°)(cutters not included) (used only with option 1950)(need option 1920)
Thread whirling head for constant profile cutters Ø 12 mm. Includes setting gage for bar up to Ø 10 mm(Inclination possible only up to 15°)(cutters not included)(used only with option 1950)(need option 1920)
398541
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2005 248-2005
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2010 248-2010
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2015 248-2015
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2020 248-2020
Options Machine20
Machine options
Description
Tool holder for frontworking with 1 hole Ø 22 mm with the ability to work simultaneously in the main and / or counter operation (Mounting in the middle position)
Tool holder for frontworking with 1 hole Ø 22 mm with the ability to work simultaneously in the main and / or counter operation (Mounting in the bottom position)
Tool holder for frontworking with 2 hole Ø 22 mm with the ability to work simultaneously in the main and / or counter operation (Mounting in the upper position)
B axis option
B axis option
B axis option
Tool holder for frontworking with 3 hole Ø 22 mm with the ability to work simultaneously in the main and / or counter operation (Mounting in the upper position)
B axis option
386269
386268
386270
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2030 248-2030
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2035 248-2035
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-2040
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-2060 248-2060
21Options Machine
Description
HF support, bore Ø 22 mm for 1 position (Mounting in the upper position)
Rotating axial drilling / milling attachment to work in main operation and counter operation Max speed : 6000 rpm for ESX 20 collet in main operation and ESX12 in counter operation
Outside thread whirling unit to work in main operation. Setting angle of 0° to 25° Max speed : 6000 rpm (Supplied without thread-whirling head)
B axis option
B axis option
B axis option
Thread whirling head for constant profile cutters Ø 12 mm. Includes setting gage for bar up to Ø 5 mm (cutters not included) - (used only with option 2040) - (requires option 1920)
386266
386271
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-2120
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-2060
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-2070
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-3100
Options Machine22
Double extension for ER16, shank Ø 25 mm
Machine options
Description
Thread whirling head for constant profile cutters Ø 12 mm. Includes setting gage for bar up to Ø 5 mm (cutters not included) (used only with option 2040)(requires option 1920)
Thread whirling head for constant profile cutters Ø 12 mm. Includes setting gage for bar up to Ø 10 mm (cutters not included)(used only with option 2040)(requires option 1920)
Front tool spindle near backspindle for ER 16, max 8000 rpm. Set of 2 spindles
2020074
417165
417174
2020024
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4130 248-4130 256-4130 258-4130 257-4130
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4120 248-4120 256-4120 258-4120 257-4120
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4110 248-4110 256-4110
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
258-4131
Tool block for end work with 1 bore Ø 22 mm for work in counter operation.
Tool block for end work with 1 bore Ø 20 mm for work in counter operation.
Tool holder for steady tools takes ESX 16 collet (not included)
Tool block with a Ø 22 mm bore for work in counter operationsMounts in positions T510 to T540 (only with machine base 258-0010)
398558
398558
398559
386220
23Options Machine
Description
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4140 248-4140 256-4140 258-4140 257-4140
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4220 248-4220 256-4220 258-4220 257-4220
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-4240 248-4240 256-4240 258-4240 257-4240 247-2110
Options Machine24
Machine options
Description
Tool block for end work with 1 bore Ø 25 mm for work in coun-ter operation.
Collet holder extension with a Ø 20 mm and 70 mm long for ER16 collet, supplied without collet (used with 4120)
Collet holder extension with a Ø 25mm and 65 mm long for ER16 collet, supplied without collet (used with 4140)
398235
246795
2020074
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
258-4500 257-4500
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-4652
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-4650
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-4600
S51 motorization to drive the back working tools (max 4 rotating tools)
Rotating milling/slotting spindle to work in counter-operation with a spindle for ER 16 collet (Used at 0 ° or 90° only) (supplied without collet) – (needed 1x 4600)
Rotating milling/slotting spindle to work in counter-operation with a spindle for ER 16 collet (Used at 0 ° or 90° only) (supplied without collet) - (needed 1x 4600)
Axial drilling attachment in counter operation for ESX16 Max. 4000 RPM (Max. 5)
389042 / 389049
25Options Machine
Description
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-5010 256-5010 258-5010 257-5010 247-5010
548-5012 248-5012 258-5012 257-5012
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5030 248-5030 256-5030 258-5030 257-5030 247-5030
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5014 248-5014 256-5014
Options Machine26
Machine options
Description
Tool break detector to check for broken cutting tools. Includes : detector, electrical interface and pneumatic control. Max 2 units per machine
Long parts extractor through the counter spindle with part recovery outside the machine in a basket. Max part length : 600 mm Ø 20 mm. According to the part size it requires at least 1 of the following kit : 5031 / 5032 / 5033
Tool break detector to check for broken cutting toolsIncludes : detector, electrical interface and pneumatic controlMax. 2 units per machine
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5031 248-5031 256-5031 258-5031 257-5031
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5032 248-5032 257-5032 258-5032 257-5032
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5033 248-5033 258-5033
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
257-5040
27Options Machine
Description
Reduction tube kitØ 4, 5, 6, 7, 8 mm (Ø 6, 8, 10, 12 mm for Swiss GT 32)
Reduction tube kitSwiss GT 13, Swiss DT 13 : Ø 9, 10, 11 mmSwiss GT 26, Swiss ST 26, Swiss DT 26 : Ø 9, 10, 11, 12, 13 mmSwiss GT 32 : Ø 14, 16, 18, 20 mm
Reduction tube kitØ 14, 15, 16, 21 mm (Ø 22, 24, 26, 28 mm for Swiss GT 32)
Middle pressure pump 20 bars 4 indenpendent outputs(delivered without oil nozzle)
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
258-5051
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5052 248-5052 256-2050 258-5050
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
258-5055
258-5056
Options Machine28
Description
Machine options
HP 20 bars pump with 4 independant outputsoutputs and IFM switch flow sensor(only with machine base 258-0010)
HP pump adjustable from 20 to 140 bars includes an additional tank of 60 liters and 4 independent outputs with 2 independent adjustable pressures for the lubrification of the tools of which : two output for platen one output for the guide bushingone output for the deep drilling(Incompatible with water soluble coolant)(delivered without oil nozzle)
HP 70 : cooling unit ***- Unit separate from the machine fitted on casters- Max. pressure of 70 bar- Max flow rate of 24 l/min.- Pressure and flow rate can be adjusted manually- 4 independent outputs, actuated by M-code- 50-litre tank- One 150 µm pre-filter and one 40 µm outlet filter- Return pump- Supplied without cooling nozzles- For emulsion only
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-5200 257-5200
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-5210 257-5210
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
256-5220 257-5220
Part extractor by vacuum for part diameter 1 mm to 3 mm part length 1 mm to 6 mm. Includes 2 boxes, volume 2x 0.11 liter Used in main and counter operation
Part catcher by oil flushing for part diameter 1.5 mm to 8 mm part length 5 mm to 15 mm used in counter operation
Part catcher at the guidebush for part diameter 1 mm to 13 mmpart lenght 1 mm to 20 mmDelivered with basket 100x50x100 mm, grid 1 mm
308131
2020342
29Options Machine
Description
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-5438 256-5438 258-5438 257-5438 247-5438
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5439 248-5439 247-5439
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5440 248-5440 256-5440 258-5440 257-5440 247-5440
Oilmist extractor (CE standard). Filtering capacity : CT 20 : 450 m3/h, Swiss DT 13 and Swiss DT 26 : 800 m3/h, Swiss GT 13 : 1000 m3/hElectro-static filter and motor with brake
Oilmist extractorFiltering capacity : CT 20 : 450 m3/h, Swiss GT 26 and Swiss GT 32 : 1000 m3/h.Electro-static filter and motor with brake
Device for centralized oilmist aspirationFlange adaptor with ID of 134 and OD of 138
243583
243583
Options Machine30
Description
Machine options
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5450 248-5450 256-5450 258-5450 247-5450
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5451 248-5451 256-5451
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-5452
Entry model chip conveyor.Hinged belt chip conveyor without filter, suitable for chips : long according to ISO 3685 type 1.1 / 2.1 / 3.1 / 4.1 / 5.1. Not compatible with option 5030 to 5033. Not suitable for short chips such as : brass, alu, steel, stainless, titanium etc. For those cases a specific solution has to be discussed with chip conveyors specialists.
Hinged belt chip conveyor without filter, suitable for chips : long according to ISO 3685 type 1.1 / 2.1 / 3.1 / 4.1 / 5.1.Compatible with option 5030 to 5033Not suitable for short chips such as : brass, alu, steel, stainless, titanium etc.For those cases a specific solution has to be discussed with chip conveyors specialists.
Hinged belt chip conveyor with integrated filter, suitable for chips : long according to ISO 3685 type 1.1 / 2.1 / 3.1 / 4.1 /5.1 / 6.1, short according to ISO 3685 type 1.2 / 2.2 / 3.2 / 4.2 / 5.2.Not compatible with option 5030 to 5033Not suitable for short chips such : titanium etc. A specific solution has to be discussed with chip conveyors specialists.
31Options Machine
Description
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5487 248-5487 256-5487 258-5487 257-5487 247-5487
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
248-5462
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5458 248-5458 258-5458
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5483 248-5483 256-5483 258-5483 257-5483 247-5483
Anti-explosion opening flap
Cutting oil regulator, 7.4 kWMax. working temperature : 40° CCooling power : 7.4 kW in an ambient temperature of 32° C.Power supply : 400 V - 3 - 50 Hz / 460 V - 3 - 60 Hz.Refrigerant fluid : R407C (CFC free)
Swiss GT 26-32 and Swiss DT 26 mid-range conveyorBelt chip conveyor without integrated filtration, with 145 litre additional tank, with two additional filtration baskets,compatible with the following chips : longs in accordance with ISO 3685 type 1.1 / 2.1 / 2.1 /3.1 / 4.1 / 5.1 / 6.1 short in accordance with ISO 3685 type 1.2 / 2.2 / 2.2 /3.2 / 4.2 / 5.2Incompatible with long parts systemsNot compatible with short chips in brass, alu, steel, stainless, titanium, etc.In these cases, a chip conveyor specialist must be contacted to develop a specific solution.
Fire extinguisher, automatic type KRAFT & BAUER FB703. (Available only in CE / CH)
Options Machine32
Machine options
Description
°C
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-5550 248-5500 256-5500 258-5500 257-5500 247-5500
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-6100 248-6100 256-6100 258-6100 257-6100 247-6100
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
247-5950
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-7054 248-7054 256-7054 258-7054 257-7054 247-7054
33Options Machine
Description
Plate for oil recovery under the machine ***
Connectivity Pack Including : PC onboard connected to RJ45 plug of the machine and TISIS Tab software
Spindle centering system – Mowidec
Machine warm-upTurn on the machine warm-up cycle manually or automatically
247137
B axis
ACB
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-7060 248-7060 256-7060 258-7060 257-7060
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-7080 248-7080 256-7080
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-7070 248-7070
Swiss GT 32 Swiss GT 26 Swiss GT 13 Swiss DT 26 Swiss DT 13 CT 20
548-7090 248-7090 256-7090 258-7090 257-7090 247-7090
CNC Software pack option- Cylindrical interpolation- Polar coordinates- Helicoidal interpolation
Milling of the Torx with G962
Automatic calculation of B axis reference point tool offset (used with 0040)
Macro Active Chip Breaker
Options Machine34
Machine options
Description
35Options Machine
Robobar SBF
Bar feeders Tornos
Main advantages :
• Reduced space requirement• Optimum integration• Guaranteed bar guidance• Easy handling and programming• Joint development between machine and barfeed• Sole supplier responsibility for machine and bar feeder
Bar feeders which perfectly enhance the capabilities of TORNOS turning machines.
* option
Robobar SBF 213 216 326 532 538
Machines Swiss GT 13 / Swiss DT 13
EvoDECO 10 / EvoDECO 16
Swiss ST 26 / Swiss GT 26 / Swiss DT 26 / CT 20
EvoDECO 20 / EvoDECO 32
Swiss GT 32
Min. barstock dia. mm 2 2 3 5 5
Max. barstock dia with preparation/ without preparation
mm 13 16/16 26 32 38
Round, hexagonal and square bar change-over
Yes Yes Yes Yes oui
Bar length m 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4
Loading system Screw loading type Side load rack Side load rack Side load rack Side load rack
Bar capacity 14 / 20* 18 bars with Ø 16 mm150 bars with Ø 2 mm
270 mm 8 bars with Ø 32 mm55 bars with Ø 5 mm
300 mm
Adjustable guide steady Yes Yes Yes Yes Yes
We keep you turning
Edit
ion
octo
bre
2019
– ©
Tor
nos
2019
, All
right
s re
serv
ed
cm TornosTORNOS SA throughout the worldRue Industrielle 111 CH-2740 MoutierPhone +41 (0)32 494 44 44Fax +41 (0)32 494 44 [email protected]
Conforms to the European CE / CEM Safety StandardsThis document is based on information available at the time of publication. While every effort has been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware and software, nor to provide for every pos-sible contingency in connection with installation, operation and maintenance. TORNOS SA assumes no obligation of notice to holders of this document with respect to changes sub-sequently made. TORNOS SA makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency or usefulness of the information contained herein. No warranties of merchant-ability nor fitness for purpose shall apply.tornos.com