sw-irmicro-1801 ir series panel switches€¦ · basic p/n bushing and bezel basic p/n 0...
TRANSCRIPT
PAN
EL S
WIT
CH
ES
• Front panel sealing : IP67 according to IEC 60529• Salt spray : IEC 512-6, test 11f• Operating temperature : -20 °C to +85 °C (-4 °F to +185 °F)
ENVIRONMENTAL SPECIFICATIONS
• Max. current/voltage rating with resistive load (microswitch) :5 A 250 VAC, 50,000 cycles (function 7)5 A 250 VAC, 25,000 cycles (function 8)
• Initial contact resistance : 100 mΩ max.• Insulation resistance : 1 GΩ min. at 500 VDC• Dielectric strength : 750 Vrms between terminals
2,000 Vrms between terminals and frame
ELECTRICAL SPECIFICATIONS
Microswitch technology up to 5 ATactile feedbackSealed to IP67Illuminated or non-illuminatedFlat round actuator for optional marking
DISTINCTIVE FEATURES
IR seriesSealed pushbutton switches • bushing Ø 16 mm •
momentary • microswitch version
• Panel thickness : 3 mm (.118) max.• Total travel : 1.6 mm (.062) ± 0.3 mm• Typical operating force : 4 N ± 2 N• Mechanical life : 1,000,000 cycles• Torque : 0.8 Nm max. applied to nut• Soldering : 320 °C (608 °F) max. for 3 sec.
GENERAL SPECIFICATIONS
LED COMPONENT SPECIFICATIONS
LED color Forward current Typ. forward voltage Max. forward voltage
Super red (0S) 20 mA 2 V 2.5 V
Yellow (0Y) 20 mA 2 V 2.5 V
Green (0G) 10 mA 2 V 2.5 V
Blue (0B) 10 mA 3.3 V 3.8 V
A resistor must be series-connected by the user.Resistor value = supply voltage - LED forward voltage
LED forward current
On flying lead versions, the LED resistorcan be integrated by APEM on request.
The company reserves the right to change specifications without notice.
1
PAN
EL S
WIT
CH
ES
SW-IRMICRO-18
01
Sealed pushbutton switches • bushing Ø 16 mm • momentary • microswitch version
IR series
CIRPC0M
(1.063)27.00
27.0
0(1
.063
)
Ø16.20(.637)
14.80(.582)
ECH 0.7
(.637DIA)Ø16.20
14.80(.582)
3.00
Max
i(.
118
max
.)
1
PANEL CUT-OUT
- Flat seal
MOUNTING
• Case : thermoplastic UL94-V0• Actuator : polyamide 6/6• Bushing/bezel : polyamide 6/6• Contacts : silver• Lens : polycarbonateAPEM products may be recycled at end-of-life for the re-claiming of valuable metal components.
MATERIALS
MATRIX MOUNTING
Function 7 (NC+NO))
ELECTRICAL FUNCTIONS
TERMINALS
Quick-connectFunction 7 (NC+NO))
Function 8 (NC/NO))
Solder lugFunction 8 (NC/NO))
CIPCOSMS4ZCIPCOSMS3Z
6.45
(.25
4)
(.110)2.80
2.50
(.09
8)
1.20(.047)
(.27
5)7.
00
(.110)2.80
1.30(.051)
ECH0.9
CIRFCTMSL-A
1 4 2 4213
ECH0.9
CIRFCTMSL-A
1 4 2 4213
CIPCOSMS4ZCIPCOSMS3Z
6.45
(.25
4)
(.110)2.80
2.50
(.09
8)
1.20(.047)
(.27
5)7.
00
(.110)2.80
1.30(.051)
ILLUMINATED MODELS
NON-ILLUMINATED MODELS
Function 7 (NC+NO)) Function 8 (NC/NO))
ECH0.9
CIRFCTMS-A
1 4 2 4213
ECH0.9
CIRFCTMS-A
1 4 2 4213
PAN
EL S
WIT
CH
ES
2
PAN
EL S
WIT
CH
ES
SERIES CONTACTSACTUATOR SHAPES
7 NC + NO(3 terminals)
8 NC/NO combined(4 terminals)
C Square
R Round, curved
P Round, flat
FRound, flush(non-illuminated - not available in satin or bright chrome)
Z Solder lug orquick-connect
2 Silver
ELECTRICAL FUNCTIONS TERMINALS
IR
BASIC PART NUMBER
Actuator marking available on round flatmodels (symbol 12 mm max.). On request.
BUILD YOUR PART NUMBER
OPTIONS
1 Blue
B Dark blue
2 Black
3 Green
4 Grey
5 Yellow
6 Red
7 White
8 Bright chrome
9 Orange
A Satin chrome
ACTUATOR COLORS
Blank Non-illuminated
L Central lens
B Bezel (round only)
ILLUMINATION LED COLORS
0 Transparent (roundbezel only)
2 Black (std)
7 White
BUSHING & BEZEL
Other : on request.
Blank Non-illuminated
0S Super red
0Y Yellow
0G Green
0B Blue
The IR series for high currents is based on a microswitch. Please note that this microswitch is supplied separately.
Sealed pushbutton switches • bushing Ø 16 mm • momentary • microswitch version
IR series
ABOUT THIS SERIES
Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information.
A sealing boot is available to protect the switches against frost and sand (P/N U7125). Round models only. See "Sealing Boots" section of website.
Mounting accessories : Standard hardware supplied : 1 hex nut 19 mm (.748) across flats and 1 flat seal. Hex nut P/N : U6715.
On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart.
3
PAN
EL S
WIT
CH
ES
ROUND - ILLUMINATED - QUICK-CONNECT TERMINALS - NC+NO - 3 TERMINALS
FLAT
Ø16.00x100SI(.630DIAx100IS)
(.574)14.60
241
(.376)9.55
2.00
5.00
18.1
0(.
196)
(.54
7)
(.07
8)
Ø16.00(.630DIA)Ø19.80
(.779DIA)
(.33
4)8.
50
2.80(.110)
(.019)0.50
5.70(.224)
CIRDTRMS3ZL-A
ECH:0.90
(.019x.019)0.5x0.5
(.019)0.50
Flat actuatorIRP7Z2 NC+NO
Curved actuatorIRR7Z2 NC+NO
-+
-+
Sealed pushbutton switches • bushing Ø 16 mm • momentary • microswitch version
IR series
ROUND - ILLUMINATED - SOLDER LUG TERMINALS - NC/NO - 4 TERMINALS
FLAT
Flat actuatorIRP8Z2 NC/NO combined
Curved actuatorIRR8Z2 NC/NO combined
ROUND - NON-ILLUMINATED - QUICK-CONNECT TERMINALS - NC+NO - 3 TERMINALS
FLAT
Flat actuatorIRP7Z2 NC+NO
Curved actuatorIRR7Z2 NC+NO
ROUND - NON-ILLUMINATED - SOLDER LUG TERMINALS - NC/NO - 4 TERMINALS
FLAT
Flat actuatorIRP8Z2 NC/NO combined
Curved actuatorIRR8Z2 NC/NO combined
+ -
Ø16.00x100SI(.630DIAx100IS)
(.574)14.60
241
(.376)9.55
2.00
5.00
18.1
0(.
196)
(.54
7)
(.07
8)Ø16.00
(.630DIA)Ø19.80(.779DIA)
(.33
4)8.
50
2.80(.110)
(.019)0.50
5.70(.224)
CIRDTRMS3Z-A
ECH:0.90(.141)3.60
0.50(.019)
(.110)2.80
6.45
(.25
4)
(.779DIA)Ø19.80 (.630DIA)
Ø16.00
(.07
8)
(.54
7)(.
196)
18.2
05.
00
2.00
10.90(.429)
3 1 2 4
14.60(.574)
(.630DIAx100IS)Ø16.00x100SI
CIRDTRMS4Z
ECH:0.90
(.141)3.60
0.50(.019)
(.110)2.80
6.45
(.25
4)
(.779DIA)Ø19.80 (.630DIA)
Ø16.00
(.07
8)
(.54
7)(.
196)
18.2
05.
00
2.00
10.90(.429)
3 1 2 4
14.60(.574)
(.630DIAx100IS)Ø16.00x100SI
CIRDTRMS4ZL-A
ECH:0.90
(.019)0.50
0.5x0.5(.019x.019)
CIRSH
Page 10-11-12-13
+ -
CIRSH
Page 10-11-12-13+ -
+ -
Terminals should be used as solder lugs only.
PAN
EL S
WIT
CH
ES
4
PAN
EL S
WIT
CH
ES
5
PAN
EL S
WIT
CH
ES
SQUARE - ILLUMINATED - QUICK-CONNECT TERMINALS - NC+NO - 3 TERMINALS
FLAT
IRC7Z2 NC+NO-+
SQUARE - ILLUMINATED - SOLDER LUGTERMINALS - NC/NO - 4 TERMINALS
FLAT
SQUARE - NON-ILLUMINATED - QUICK-CONNECT TERMINALS - NC+NO - 3 TERMINALS
FLAT
SQUARE - NON-ILLUMINATED - SOLDER LUG TERMINALS - NC/NO - 4 TERMINALS
FLAT
Sealed pushbutton switches • bushing Ø 16 mm • momentary • microswitch version
IR series
Ø16.00x100SI(.630DIAx100IS)
(.574)14.60
241
(.376)9.55
2.00
5.00
18.1
0(.
196)
(.54
7)
(.07
8)(.
334)
8.50
2.80(.110)
5.70(.224)
CIRDTCMS3Z-B
ECH:0.90
(.019)0.50
(.779SQUARE)19.80
16.00(.629SQUARE)
Ø16.00x100SI(.630DIAx100IS)
(.574)14.60
241
(.376)9.55
2.00
5.00
18.1
0(.
196)
(.54
7)
(.07
8)(.
334)
8.50
2.80(.110)
(.019)0.50
5.70(.224)
CIRDTCMS3ZL-B
ECH:0.90
(.019x.019)0.5x0.5
(.019)0.50
(.779SQUARE)19.80
16.00(.629SQUARE)
(.141)3.60
0.50(.019)
(.110)2.80
6.45
(.25
4)(.
078)
(.54
7)(.
196)
18.2
05.
00
2.00
10.90(.429)
3 1 2 4
14.60(.574)
(.630DIAx100IS)Ø16.00x100SI
CIRDTCMS4Z-A
ECH:0.90
19.80(.779SQUARE)
(.629SQUARE)16.00
(.141)3.60
0.50(.019)
(.110)2.80
6.45
(.25
4)(.
078)
(.54
7)(.
196)
18.2
05.
00
2.00
10.90(.429)
3 1 2 4
14.60(.574)
(.630DIAx100IS)Ø16.00x100SI
CIRDTCMS4ZL-B
ECH:0.90
(.019)0.500.5x0.5
(.019x.019)
19.80(.779SQUARE)
(.629SQUARE)16.00
IRC8Z2
IRC7Z2 NC+NO
CIRSH
Page 10-11-12-13
IRC8Z2 NC+NO
+ -
NC/NO combined+ -
Terminals should be used as solder lugs only.
Terminals should be used as solder lugs only.
LED COLORS
BASIC P/N
ACTUATOR COLORS
ILLUMINATION
Blank Non-illuminatedL Central lensB Bezel (round only)
BASIC P/N
BUSHING AND BEZEL
BASIC P/N
0 Transparent (round bezel only) 2 Black (standard)7 White
BASIC P/N
Blank Non-illuminated05 Super red0Y Yellow0G Green0B Blue
1 BlueB Dark blue2 Black3 Green4 Grey5 Yellow6 Red7 White8 Bright chrome9 Orange A Satin chrome
Sealed pushbutton switches • bushing Ø 16 mm • momentary • microswitch version
IR seriesPA
NEL
SW
ITC
HES
6