suture material cabinet - ht group · suture material cabinet the body of the suture material...
TRANSCRIPT
HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • [email protected] • www.htgroup.de
Medical Installations
Version November 7th 2016 – subject to technical alterations
SUTURE MATERIAL CABINET
The body of the suture material cabinet is made entirely of ground stainless steel. The front side consists of two glass doors. Glass shelves can
be fitted at various heights in the body. The suture material cabinet is installed flush into every wall system.
DIMENSIONS (standard design)
Height 600 mm
Width 1070 mm
Depth 170 mm
Clear depth (shelf) 155 mm
Installation height 1200 mm
BODY
Material made of stainless steel (Mat. no. 1.4301)
Shelves 8 mm single-pane safety glass (ESG) I able to be inserted at various heights
Quantity according to customer wishes
Mounting rails for the fitting of the shelves I two pieces for each shelf
Installation flush with every wall system
GLASS DOORS
Material 8 mm single-pane safety glass (ESG)
Locking system magnetic snap-lock
Door handles one doorknob for each door panel
Glass edging especially for glass doors I two pieces for each door panel
MATERIAL AND SURFACE TREATMENT
Disinfection resistant against cleaning agents and disinfectants
ADDITIONAL FEATURES
Suture material boxes space for four boxes (150 x 500 x 220 mm I special dimensions possible)
HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • [email protected] • www.htgroup.de
Medical Installations
Version November 7th 2016 – subject to technical alterations
HATCH
The hatch is a horizontal pass-through sliding system. The pass-through element is moved horizontally by hand. Frame and hatch door panel are
manufactured from ground or powder-coated stainless steel. The hatch may be installed to open either on the right or left.
DIMENSIONS
Clear frame width variable up to 1 m² (width x height)
Clear pass-through width A – 125 mm (with bow handle on both sides)
Frame outer dimension A + 100 mm
Wall thickness up to 250 mm
Installation height according to customer wishes
Length of door drive box 2 x A + 100 mm
FRAME
Material ground stainless steel I powder-coated (with surcharge)
Frame type closed frame I sliding in front of the wall
Tray ground stainless steel I welded to the frame
Substructure additional cross members for fixing
HATCH DOOR PANEL
Material ground stainless steel I powder coated (with surcharge)
Door handles bow handles I recessed handles
Colour as an option according to colour chart
DRIVE
Drive type handrail
Trolley with ball-bearing mounted profiled rollers and final dampers
SPECIAL FITTINGS
X-ray protection Pb 0.5–3 mm
HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • [email protected] • www.htgroup.de
Medical Installations
Version November 7th 2016 – subject to technical alterations
OR SLAVE CLOCK
Independent clocks/individual clocks
Quartz clock: Independent clocks for which manual setting is required when starting up, essentially without automatic summer/winter time change-
over. Mains connection is possible.
Radio-controlled clock: Independent, precise clocks which are synchronised by the German DCF77 time signal transmitter within an approx.
1500 km radius around Frankfurt/Main. Fully automatic clock hand movement control (of analogue clocks) and summer/winter time changeover are
present.
System clocks and master clock technology
Pulse slave clock: A system clock which is controlled by a master clock with 12/24 V pole changing minute/second pulses.
Signalling clock: Intelligent slave clock which is controlled by a TELNU master clock with a serial time string (seconds, minutes, hours, day, month,
day of the week and year) without any additional cable (operating voltage and data transfer via a two-wire cable).
Fitting
The clock is fitted into the mounting opening without the need for screws by means of spring compressors on the rear side. The opening section is
355 mm. The stainless steel mounting frame is pre-fitted on the rear with closed-pore, self-adhesive sealing tape.
DIMENSIONS
Standard clock face30 cm I as an option 25 cm/40 cm as special version
Housing diameter 36 cm
Detection range 20 cm
EQUIPMENT FEATURES
Housing material stainless steel (Mat. no. 1.4301)
Covering impact resistant polycarbonate
Clock face printing in accordance with DIN 41091
Clock face variant ZF and ZA as standard
Clock face base white RAL 9010
Clock face printing black RAL 9004
Hour/minute hand silk matt RAL 9005
Second hand blood orange
Total weight 1.1 kg
HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • [email protected] • www.htgroup.de
Medical Installations
Version November 7th 2016 – subject to technical alterations
TECHNICAL DATA
Bed frame
Square profiles 80 x 40 x 2 mm I 40 x 40 x 2 mm I 20 x 20 x 2 mm I made of ground stainless steel (Mat. no. 1.4301) I welded together
Bed housingrear and side panels made of 1.5 mm galvanised steel
Front panel1 mm galvanised steel I with plaster board glued to the rear
Colourpowder-coating according to HT colour chart
Opening I Closing
open position 90°: Space in the room approx. 2090 x 800 mm I closed position 0°: Bed is flush with the wall panels
Handle stainless steel bar handle
Mattress black synthetic leather
Bed fittings 2 x gas pressure string with 80 kg
Media rail (optional) with electrical sockets for power and IT
Lighting unit (optional) LED bed lamp (with surcharge)
DIMENSIONS
Width 2100 mm
Installation depth 252 mm
Height 1000 mm (in closed position)
Installation height 300 mm
Mattress 2008 x 908 x 80 mm
Space in open position approx. 2090 x 800 mm
HT BED UNIT
FOR PATIENT & ICU ROOMS
The HT Bed Unit is installed flush with the wall panels in ICUs and patient rooms. An ideal solution for visitors who want to stay overnight,
because the bed can be both set up and dismantled quickly. In the closed position the bed unit is flush with the wall panels. The HT Bed
Unit is an almost equivalent replacement of a normal bed.
4)
3)
1)
2)
1 Bed frame2 Bed housing3 Mattress4 Front panel