sustainable – efficient – rapid – profitable · pdf filebezaktiv red go and...
TRANSCRIPT
GO FOR SUCCESS GO FOR SUSTAINABILITY
> GO FOR SUSTAINABILITY Minimum consumption of water, energy and salt
> GO FOR INTENSITY Premium quality colour intensity
> GO FOR PROCESS SAFETY Extremely balanced exhaust and fixing properties
> GO FOR HIGH SPEED Very short process times in exhaust and CPB processes
> GO FOR SUCCESS BEZAKTIV GO
Reduction of water and energy consumption as well as the amount of salt released into our ecological systems are global challenges that decide over the future of the current and future generations.
The amount of water and energy consumed during conventional dyeing is tremendous. In recent years vigorous attempts have been made to save water and energy, especially by reducing the number and temperature of the rinsing baths. This approach has been consistently contin-ued with the development of the colour-inten-sive BEZAKTIV GO dyes. The new dye tech-
nology enables the revolutionary GO process with even lower temperatures during dyeing and rinsing. 40 °C rinsing baths are sufficient for most dyeing applications!At the same time the process time is reduced considerably as fewer rinsing baths are re-quired at a lower temperature. Productivity is enhanced as a result without any expensive investments.
Time in minutes
Commodities BEZAKTIV GO / GO-Process
Tem
per
atur
e in
°C
100
90
80
70
60
50
40
30
20
10
00 50 100 150 200 250 300
Process comparison:
GO FOR MINIMAL WATER CONSUMPTION
Only small amounts of hydrolysate are pro-duced during the use of BEZAKTIV GO dyes which can be easily washed out. The use of
COTOBLANC SEL in the second rinsing bath also improves the rinsing efficiency further.
Commodities
BEZAKTIV GO
Residual liquor 1st rinsing bath 2nd rinsing bath 3rd rinsing bath 4th rinsing bath 5th rinsing bath 6th rinsing bath
50 °C 70 °C 98 °C 70 °C 50 °C 30 °C
Residual liquor 1st rinsing bath 2nd rinsing bath 3rd rinsing bath
40 °C 40 °C 40 °C
1 g/l COTOBLANC SEL
Fastness of dyeing with BEZAKTIV GO after three rinsing baths at 40 °C
Colour fastness to washing 60 °C Colour fastness to water severe
GO FOR EFFICIENCY GO FOR PROCESS SAFETY
Efficiency is the leitmotif of the entire GO pro-cess. This starts with the high colour intensity of the BEZAKTIV GO dyes and the resulting lower dye and salt requirements through to
> OPTIMUM TERNARY
The basis of the BEZAKTIV GO dyes are the proven elements BEZAKTIV Orange GO2), BEZAKTIV Red GO and BEZAKTIV Navy GO
with their effectively harmonising dyeing be-haviour.
Commodities BEZAKTIV GO / GO-Process
Co
mp
aris
on
in %
600
500
400
300
200
100
0Dyestuff
consumptionSalt
consumptionWater
consumptionOil consumption
for steam generation
Process time
Comparison of the main cost factors:
Bath exhaustion:
the optimised washing process. Invest now in a cost-saving, future-oriented technology to minimise the ecological footprint of your production facilities.
100
90
80
70
60
50
40
30
20
10
0
pH °C mS/cm
12.6 126 252
11.2 112 224
9.8 98 196
8.4 84 168
7.0 70 140
5.6 56 112
4.2 42 84
2.8 28 56
1.4 14 28
0.0 0 00 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
Time in minutes
Orange GO2) Red GO Navy GO
pH value temperature electrolyte
2) This offer is not valid in the following countries: Australia, Belgium, Canada, China, France, Germany, Great Britain, Hong Kong, Indonesia, Italy, Japan, Liechtenstein, Netherlands, New Zealand, Portugal, Spain, Switzerland, Taiwan, USA.
GO FOR PROCESS SAFETY GO FOR HIGH SPEED
Supplementary elements:BEZAKTIV Golden Yellow GO1) Brighter alternative to BEZAKTIV Orange GO2)
BEZAKTIV Scarlet GO Alternative to BEZAKTIV Red GO for light-fast dyeing resultsBEZAKTIV Blue GO For bright blue and green shadesBEZAKTIV Dark Blue GO Alternative to BEZAKTIV Navy GO for light-fast dyeing resultsBEZAKTIV Black GO2) Deep black with the highest fastness properties already after
rinsing baths at 60 °CBEZAKTIV Velvet Black GO Deep black with a neutral shade, non-staining of PA-fibres
> BEZAKTIV GO DYES IN THE COLD PAD-BATCH PROCESS
BEZAKTIV GO dyes do not only fix rapidly during the exhaust process, but can also increase productivity in the CPB process. Standard dyes normally need a minimum fixing time of 12 – 16 hours in the CPB process. If the dwelling time is shorter,
GO AHEAD WITH BEZAKTIV GO AND TAKE ON RESPONSIBILITY!
not all ternary dyes are fully fixed, so that the colour depth and especially the shade deviates from the setting. BEZAKTIV GO dyes already reach their fully fixed condition at an ambient temperature of 20 to 25 °C after a dwelling time of six hours or less.
dE: 0.22 dE: 0.17 standard
4 hours dwelling time 6 hours dwelling time 20 hours dwelling time
Sustainable dyeing in all shades:
Fixing speed in the CPB process:
1) This offer is not valid in Mexico.2) This offer is not valid in the following countries: Australia, Belgium, Canada, China, France, Germany, Great Britain, Hong Kong,
Indonesia, Italy, Japan, Liechtenstein, Netherlands, New Zealand, Portugal, Spain, Switzerland, Taiwan, USA.
100
80
60
40
20
0
– 20
– 40
– 20 – 10 0 10 20 30 40 50 60 70
DYEING METHODS
BEZAKTIV GO dyes are tailor-made dyes for the ecological and economical GO process. The high fixation values of BEZAKTIV GO enable the washing-off of hydrolysate at 40 – 60 °C in 3 – 4 rinsing baths. The temperature and the number of rinsing baths depend on colour depth, carry-over and liquor ratio. Perfect wet fastnesses are achieved when the process is completed with a cationic after-treatment. In addition, they are perfectly suitable for all common processes in exhaust, semi-continuous and continuous dyeing.
> EXHAUST PROCESS FOR BEZAKTIV GO
The optimal dyeing temperature is 40 – 60 °C. The appropriate dyeing temperature depends not on the dyestuffs, but on the articles and machinery. E.g. for yarn, dense articles or viscose a higher temperature is advantageous. BEZAKTIV GO dyes can be used both on exhaust machines (jet, overflow) and also on exhaust apparatus (cross-package or warp beam dyeing apparatus, beam dyeing apparatus). The recommended auxiliaries and the correct amounts of salt and alkali are given in the following process description.
GO processThe most advanced dyeing and rinsing process is only feasible with BEZAKTIV GO dyes. The reduced temperature leads to an increased process safety due to better control of fixation speed and a reduced hydrolysis of unfixed dye for highest possible
colour yield. If the dosage is monitored, sodium carbonate and caustic soda can be added simultaneously. With progressive alkali dosing a steady increasing fixing curve and therefore the best possible levelness is reached.
A1.0 – 2.0 g/l SARABID MIP
1.0 – 2.0 g/l BIAVIN BPA
10.0 – 90.0 g/l Common salt or Glauber’s salt
B x % BEZAKTIV GO dye
C5.0 g/l Sodium carbonate
1.0 – 4.0 ml/l Caustic soda 38 °Bé (add progressively within 45 min)
D 1.0 g/l COTOBLANC SEL
E 1.0 m/l Acetic acid 80 %
3.0 % REWIN ACP
0
0
10
20
30
40
50
60
70
80
90
100
20 40 60 80 100 120 140 160 180 200 220
Time in minutes
Tem
per
atur
e in
°C
A B C 45 – 60 minutes D E
Temperature step processProcess which is mainly used for dyeing on machines without a suitable dosing device. To prevent unlevelness, the alkali should be added in portions. Furthermore this process can be used to improve the tone-in-tone dyeing of cotton/viscose blends.
A
1.0 – 2.0 g/l SARABID MIP
1.0 – 2.0 g/l BIAVIN BPA
10.0 – 90.0 g/l Common salt or Glauber’s salt
5.0 – 10.0 g/l Sodium carbonate
x ml/l Caustic soda 38 °Bé (add 20 % of the total quantity)
B y % BEZAKTIV GO dye
C z ml/l Caustic soda 38 °Bé (add 80 % of the total quantity)
D 1.0 g/l COTOBLANC SEL
E 1.0 ml/l Acetic acid 80 %
3.0 % REWIN ACP
0
0
10
20
30
40
50
60
70
80
90
100
20 40 60 80 100 120 140 160 180 200 220
Time in minutes
Tem
per
atur
e in
°C
A B
D EC 30 – 45 minutes
Liquor ratio Factor
1:51:8 – 1:12
1:151:20
1.301.000.800.65
Liquor ratio Factor
1:51:8 – 1:12
1:151:20
– 10 g/l saltas per table+ 10 g/l salt+ 20 g/l salt
Salt- and alkali requirement for BEZAKTIV GO dyes
For unmercerised cotton in liquor ratio 1:8 – 1:12
GO process* 60 °C dyeing60 °C dyeing only soda ash
dyestuff salt soda ashcaustic soda
38 °Bésoda ash
caustic soda 38 °Bé
soda ash
% g/l g/l ml/l g/l ml/l g/l
< 0.1 10 5 1.5 5 – 5
0.1 – 0.5 20 5 2.0 10 – 10
0.5 – 1.0 30 5 2.5 5 1.0 15
1.0 – 2.0 40 5 3.0 5 1.5 15
2.0 – 3.0 50 5 3.5 5 2.0 20
3.0 – 4.0 60 5 4.0 5 2.5 20
4.0 – 5.0 70 5 4.5 5 3.0 25
5.0 – 6.0 80 5 5.0 5 3.5 25
> 6.0 90 5 5.0 5 3.5 25
* recommended pH level between pH 11.8 – 12.3
For mercerised cotton and viscose in liquor ratio 1:8 – 1:12
GO process 60 °C dyeing60 °C dyeing only soda ash
dyestuff salt soda ashcaustic soda
38 °Bésoda ash
caustic soda 38 °Bé
soda ash
% g/l g/l ml/l g/l ml/l g/l
< 0.1 10 5 1.2 5 – 5
0.1 – 0.5 20 5 1.5 7.5 – 7.5
0.5 – 1.0 30 5 1.9 5 0.8 10
1.0 – 2.0 40 5 2.3 5 1.2 15
2.0 – 3.0 50 5 2.7 5 1.5 15
3.0 – 4.0 60 5 3.0 5 1.7 20
4.0 – 5.0 70 5 3.3 5 2.0 20
5.0 – 6.0 80 5 3.6 5 2.2 25
> 6.0 90 5 4.0 5 2.5 25
> SEMI-CONTINUOUS PROCESS
Woven and knitted fabric made of cellulose or regenerated cellulose can be dyed very economically with the cold pad batch (CPB) process with BEZAKTIV GO dyes. When BEZAKTIV GO dyes are combined with BEZAKTIV V or S, it should be ensured that dyes with the same dyeing properties such as fibre affinity, liquor stability and fixing speed should be used. This information is given in the respective tables. To prevent tailing during padding, a high liquor exchange should be ensured. With lightweight fabrics dyeing should be performed with a low trough level and a high running speed. A low liquor stability can result in tailing. To ensure a high liquor stability it is highly recommended that the temperature of the padding liquor is not higher than 25 °C. Dye and alkali solution with a 4:1 ratio are combined just before the padder with a mixing pump or doser and added to the dye trough. The application amounts of dye, auxiliaries and fixing alkalis are based on the overall volume of the padding liquor. It is important that the fabrics have been cooled properly before padding to ensure reproducibility. If the fabric tem-perature is too high, the liquor stability is lowered which results in a change of colour or its depth. A constant production speed should generally be ensured. Different speeds influence the liquor pick-up and result in tailing. During dyeing the fabric is rolled with a straight line fabric. In order to ensure optimum fixation of the dye, the dyed goods must be packed with an air-tight plastic film and left for a certain time at room tempera-ture. Packing the goods with an airtight package prevents carbon dioxide from the air partially neutralising the fixing alkali. When dyeing with several dyes the dwelling time of the dye with the longest dwelling time should be taken.
Cold pad batch process with reduced sodium silicate quantityThe reduced silicate version is the standard version and has a high pad liquor stability in the temperature range of 20 – 30 °C. The application amount of sodium silicate 38 °Bé is generally 50 ml/l. Addition of the dye with the fixing alkali is performed with a mixing pump with a ratio of 4:1. To prevent silicate deposits on the rollers, intensive rinsing before neutralisation is essential.
Dye solution: x g/l BEZAKTIV GO dye 1 – 3 g/l COLORCONTIN VGP
Alkali solution: 50 ml/l Sodium silicate 38 °Bé y ml/l Caustic soda
32.5 % (38 °Bé)
Mixing ratio: The stated quantities g/l of dye, ml/l of sodium silicate and ml/l of caustic soda 32.5 % (38 °Bé) are based on the total volume of the padding liquor. Dye and alkali solution are combined with a mixing pump with a normal mixing ratio of 4:1 and form the total padding liquor volume.
Padding liquor temperature:20 – 25 °C
Dwelling time:6 – 24 hours, up to 40 hours no colour loss-es or shifts in shade occur.
Conversion factors to determine the alkali requirements depending on the liquor ratio
Conversion factors to determine the salt requirements depending on the liquor ratio
g/l BEZAKTIV GO dye
ml/
l Cau
stic
so
da
32.5
% (
38 °
Bé)
40
35
30
25
20
15
10
0 20 30 40 50 60 70 80 90 100
Alkali concentration for the reduced sodium silicate process:
Technical application notes for dyeing according to the CPB process:
Dye designation Fibre affinity Liquor stability Fixation speed Minimum fixing time
BEZAKTIV Golden Yellow GO1) Medium Low Fast 6 hours
BEZAKTIV Orange GO2) Medium Medium Fast 6 hours
BEZAKTIV Scarlet GO Medium Low Fast 6 hours
BEZAKTIV Red GO Medium Medium Fast 6 hours
BEZAKTIV Blue GO Medium Medium Fast 8 hours
BEZAKTIV Dark Blue GO Medium Medium Fast 6 hours
BEZAKTIV Navy GO High Medium Fast 6 hours
BEZAKTIV Black GO2) High Medium Fast 6 hours
BEZAKTIV Velvet Black GO High High Fast 6 hours
Table information: The given dye specifications were deter-mined with use of the reduced sodium silicate method (50 ml/l) and caustic soda 38 °Bé with 30 g/l dye at a padding and dwelling temperature of 25 °C.
Fibre affinity:The fibre affinity was determined by adding alkali and characterises the specific exhaus-tion properties of a dye. To avoid tailing problems, the use of dyes with the same fibre affinity is advantageous.
Padding liquor stability:The padding liquor stability is given in minutes. A period of time for hydrolysis of 10 % of the employed dye is determined. This theoretical value cannot be implemented directly in practice, as the dye and alkali solution are constantly added to the trough. For this reason the actual value of the liquor replacement in the trough should not exceed three minutes. The values of the BEZAKTIV GO dyes were determined at a temperature of 25 °C and with the use of the reduced sodium silicate variant. A higher temperature and different alkali systems influence the liquor stability.
The BEZAKTIV dyes are categorised as follows:Low < 10 minutesMedium 10 – 20 minutesHigh > 20 minutes
Fixation speed:The speed of fixation depends greatly on the dwelling temperature. A regular temperature of the dyed fabric, liquor and environment is a requirement for regular fixation. The stated values of the BEZAKTIV GO dyes are based on an ambient temperature of 25 °C during dwelling. If the ambient temperature is lower, the dye is fixed more slowly. For this reason it is necessary to adapt the dwelling time accordingly.
The BEZAKTIV dyes are categorised as follows:Slow > 16 hoursMedium 8 – 16 hoursFast < 8 hours
1) This offer is not valid in Mexico.2) This offer is not valid in the following countries: Australia, Belgium, Canada, China, France, Germany, Great Britain, Hong Kong,
Indonesia, Italy, Japan, Liechtenstein, Netherlands, New Zealand, Portugal, Spain, Switzerland, Taiwan, USA.
> CONTINUOUS DYEING PROCESS
Pad dry pad steam processThe pad dry pad steam process is the classic continuous process for dyeing woven fabrics. It is primarily used for cellulose articles with a high yardage. This process is characterised by a high productivity, a good fabric appearance as well as a good colour yield. The use of a dosing pump is not necessary with this process.
Dye pad: x g/l BEZAKTIV GO dye 1.0 – 3.0 g/l COLORCONTIN VGP 1.0 – 5.0 g/l MEROPAN XR GRANULATE 5.0 – 10.0 g/l MIGRASOL SAP
Pick up: 60 – 80 %
Padding temperature: 20 – 30 °C
Pre-drying to a residual moisture content of 30 – 35 % in the IR zone
Drying: 110 – 120 °C
Padding of chemicals: 250 g/l Common salt 20 g/l Sodium carbonate7.5 – 15 g/l Caustic soda 38 °Bé
Pick up: 80 – 100 %
Padding temperature: 20 – 30 °C
Fixation: Steaming with 102 °C saturated steam for 60 – 90 seconds.
Alkali requirements
Dye g/l < 20 20 – 40 > 40
Caustic soda 38 °Bé ml/l 7.5 10 15
Remarks: Regular pre-drying is necessary to ensure optimum reproducibility and a level fabric appearance.
Pad dry thermofix processThe pad dry thermofix process is a single-bath and salt-free continuous process. Particularly suitable for light to medium shades. A lower light fastness level is achieved compared to the pad dry pad steam process. No dosing pump is required for this process. Fixation is performed with hot air. Sodium bicarbonate is recommended as a fixing alkali, because of higher liquor stability than sodium carbonate.
Dye pad: x g/l BEZAKTIV GO dye 1.0 – 3.0 g/l COLORCONTIN VGP 1.0 – 5.0 g/l MEROPAN XR GRANULATE 5.0 – 10.0 g/l MIGRASOL SAP 0 – 150 g/l Urea x g/l Sodium bicarbonate
Pick up: 60 – 80 %
Padding temperature: 20 – 30 °C
Pre-drying to a residual moisture content of 30 – 35 % in the IR zone
Drying: 110 – 120 °C
Thermofixation: 60 – 180 seconds at 150 °C
Alkali requirements (sodium bicarbonate)
Dye g/l 5 10 20 30 > 30
Sodium bicarbonate g/l 10 15 20 25 30
Remarks:Regular pre-drying is necessary to ensure optimum reproducibility and a level fabric appearance.
0.27 % 1.6 %
BEZAKTIV Golden Yellow GO1)
BEZAKTIV Orange GO2)
BEZAKTIV Scarlet GO
BEZAKTIV Red GO
BEZAKTIV Blue GO
BEZAKTIV Dark Blue GO
0.20 % 1.2 %
0.23 % 1.4 %
0.40 % 2.4 %
0.50 % 3.0 %
2.20 % 4.4 %
BEZAKTIV GODyes
HIGH PERFORMANCERanges of top products and specialities offering state of the art technology and meeting the highest demands.
HP
Products comply with the strict ecological and toxicological requirements of the bluesign® criteria.
1) This offer is not valid in Mexico.2) This offer is not valid in the following countries: Australia, Belgium, Canada, China, France, Germany, Great Britain, Hong Kong,
Indonesia, Italy, Japan, Liechtenstein, Netherlands, New Zealand, Portugal, Spain, Switzerland, Taiwan, USA.
neutral
100
100
100
100
100
100
CPB
100
60
80
80
100
100
3/11/1
1/25
n.d.5-64-5
n.d.4-53-4
n.d.6
4-5
n.d.4-53-4
n.d.6-75-6
64-5n.d.
CCCOCV
4-555
4-555
455
4-555
54-55
4-555
455
444
3-44-55
44
4-5
445
445
CCCOPA
4-555
555
455
4-555
555
4-555
CCCOPA
4-555
4-555
3-455
4-555
4-555
4-555
CCCOPA
4-555
4-555
3-455
4-555
4-555
4-555
CC
1
3-4
2
3-4
2-3
3
CC
1-2
3-4
3-4
3-4
3-4
4
1/11/25
++
(+)+
++
–+
–+
(+)+
CPB°C
+40-60
+40-60
+40-60
+40-60
+40-60
+40-60
–
–
–
–
+
+
Solubility
25 °C
in g/l
Light Washing
°C
Perspiration
Chlo
rine
was
hing
Water 20 ppm
Chlo
rina
ted
wat
er
Disc
harg
eabi
lity
Suita
bilit
y fo
r CP
BEx
haus
tion
tem
p.
Met
al c
ompl
ex
alkal.acid
60 95
Data about fastness properties:
The fastness properties indicated in this shade card were determined on 1/1 standard depth dyeings on bleached mercerised cotton, except for BEZAKTIV Navy GO which was determined on 2/1.
Fastness to light DIN EN ISO 105-B02Fastness to washing at 60 °C DIN EN ISO 105-C06/C2SFastness to washing at 95 °C DIN EN ISO 105-C06/E2SFastness to water DIN EN ISO 105-E01Fastness to perspiration DIN EN ISO 105-E04Fastness to washing with hypochlorite DIN EN ISO 105-C06/D3SFastness to chlorinated water DIN EN ISO 105-E03(swimming pool water) Dischargeability + suitable for white discharge (+) suitable for coloured discharge – not dischargeable n.d. not determined
Impression énergétiquement efficiente et CO2 compensé SC2012040303 - swissclimate.ch
imprimé CO2 neutre
Energy efficient and CO2 compensated print SC2012040303 - swissclimate.ch
printed carbon neutral
Energieeffizient gedruckt und CO2 kompensiert SC2012040303 - swissclimate.ch
klimaneutral gedruckt
Compensazione delle emissioni di CO2 SC2012040303 - swissclimate.ch
stampa a impatto zero
HIGH PERFORMANCERanges of top products and specialities offering state of the art technology and meeting the highest demands.
HP
1.00 % 2.0 %
BEZAKTIV Navy GO
BEZAKTIV Black GO2)
BEZAKTIV Velvet Black GO
1.70 % 5.0 %
1.70 % 5.0 %
BEZAKTIV GODyes
Products comply with the strict ecological and toxicological requirements of the bluesign® criteria.
1) This offer is not valid in Mexico.2) This offer is not valid in the following countries: Australia, Belgium, Canada, China, France, Germany, Great Britain, Hong Kong,
Indonesia, Italy, Japan, Liechtenstein, Netherlands, New Zealand, Portugal, Spain, Switzerland, Taiwan, USA.
neutral
100
100
100
CPB
80
80
100
3/11/1
1/25
54
n.d.
54-5n.d.
54-5n.d.
CCCOCV
4-555
4-555
4-555
44
4-5
4-555
44-54-5
CCCOPA
4-54-54-5
555
555
CCCOPA
555
4-555
4-555
CCCOPA
555
4-555
4-555
CC
2
1
1
CC
3-4
4
3-4
1/11/25
++
++
++
CPB°C
+40-60
+40-60
+40-60
–
–
–
Solubility
25 °C
in g/l
Light Washing
°C
Perspiration
Chlo
rine
was
hing
Water 20 ppm
Chlo
rina
ted
wat
er
Disc
harg
eabi
lity
Suita
bilit
y fo
r CP
BEx
haus
tion
tem
p.
Met
al c
ompl
ex
alkal.acid
60 95
B E Z E M A A G | Kriessernstrasse 20 | CH-9462 Montlingen | Tel +41 71 763 88 11Fax +41 71 763 88 88 | www.bezema.com | [email protected]
C H T R . B E I T L I C H G M B H | Bismarckstraße 102 | D-72072 Tübingen | Tel +49 7071 154-0Fax +49 7071 154-290 | www.cht.com | [email protected]
DACHCOM
03/1
7_en