suruburi autoforante sfs
TRANSCRIPT
-
7/23/2019 SURUBURI AUTOFORANTE SFS
1/88
Technical values for fastener fromSFS intec
Pitched roofing and
cladding fastening
systems for the
constructions industry
-
7/23/2019 SURUBURI AUTOFORANTE SFS
2/88- 2 -
OTensile breaking load
O Shear breaking load
O Pull-out load
O Pull over load
O Shear load
Legend:St37 = 375 N/mm2
St52 = 530 N/mm2
Alu = 230 N/mm2
Part II
Part I
The pull-out value Fz is the load whic mustbe exerted in the axial direction of the fa-stener to pull the fastening out of the sub-structure. It is dependent only upon thetype of fastener and the substructure.
The tensile breaking load Zb is thebreaking load of the fastener in this axialdirection. It is dependent only upon thetype of fastener.
The shear breaking load Qb is the breakingload of the fastener perpendicular to itsaxis. It is dependent only upon the type offastener.
The pull over value Fu is the load whichmust be exerted in the axial direction of
the fastener to cause the failure of theattached material by pulling it over thehead of the fastener. It is dependent onlyupon the type of fastener and thesubstructure and the material beingattached.
The shear load value Fq ist the load whichmust be exterted perpendicular to the or-ginal axis of the fastener to cause the fai-lure of the substructure or of the material
being atteched. It is dependent only uponthe type of fastener and the substructureand the material being attached.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
3/88
self-drilling fastener instainless steel and aluminium
Standing seam andsecret fix systems
Standing seam andsecret fix systems
Roofing and cladding
Content
SXSXCSXWSW-SSW-ASXLSL-SSL-A
TDA-STDB-STDC-S
SD, SDC, SDLSW-TSL
TDA-TTDB-TTDBL
SDKSXSXW
SX6/SX12RV6604
SXCSXCWTD-SSXLSL-S
SCFWSCFW-SSCF3/SCF12
TT/TTNASOASCATOATCTTOSSCCNSOGA-ASGA-BS
self tapperin stainless steel
self-drilling-fastenercorrosion protected
self tappercorrosion protected
stainless steel self drillingfastener, self tapper,Bulb-Tite
stainless steel self drillingfastener, self tapper
self-drilling fastener to wood
self-drilling fastener to steel
Bulb-Tite, blind rivets,scafolding anchors
External single and twinskin construction
Fibre cement
Special fastener and rivets
SDT, SDP, SDTW,
-
7/23/2019 SURUBURI AUTOFORANTE SFS
4/88
Sleeve anchor, Nylon frameplug, self-drilling fastener,rivet, facade screw
Content
MB (SDF-K)MBR (SDF-S)TW-S/TW-A4AP11AP14AP16SDA3-SSLA5TU-S
Rainscreen cladding
-
7/23/2019 SURUBURI AUTOFORANTE SFS
5/88
Technical value
Material Thickness (mm) x s
St37 (375 N/mm2) 1,25 2905 58
St52 (530 N/mm2) 1,25 3584 76
SX2
Admission: no
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:
- Hex., 8 mm A/F
Pull-out load FZ(N)
Shear breaking load Qb (N)
Part II (Subconstruction)
Tensile breaking load Zb (N)
SX2 6,3xL
x = 16000
x = 12000
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Washer A14
Pull-over load Fu (N)
Material Sheet thicknessPart I
(mm) x s
Alu (230 N/mm2) 2,0 7419 316
Part II
Part I
August/2003 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
6/88
Technical value
Material Thickness (mm) x s
S235 (375 N/mm2) 1,0 1500 901,5 2700 1102,0 3800 1402,5 5000 170
2x0,63 1900 402x0,75 2300 702x1,0 3300 1002x1,25 4300 130
S355 (530 N/mm2) 1,0 2100 901,25 3008 661,5 3500 1202,0 5200 1402,5 8400 190
2x0,63 2300 3202x0,75 2800 3002x1,0 4000 2502x1,25 5100 200
Alu (230 N/mm2) 1,5 2100 802,0 2900 1102,5 3800 130
2x0,63 1000 702x0,75 1600 120
2x1,0 2300 1602x1,2 3100 200
SX3
Admission: SX3
SX3-L12
DIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
SizeHead/Drive:- Hex., 8 mm A/F
- L12 Head ( 12 mm) irius
Drive-D12 pan head ( 12 mm) Torx T25
Pull-out load FZ(N)
Shear breaking load Qb (N)
Part II (Subconstruction)
Tensile breaking load Zb (N)
SX3 5,5xL
SX3L12 5,5xL
SX3D12 5,5xL
x = 14000
x = 9500
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
May/2006 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
7/88
Part II
Part I
SX3
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Technical value May/2006 sre/abjo
x = arithmetical mean values =Standard deviation
1 =Pull-over load fail in Part I
Material BlechdickePart I
(mm) x s x s x s x sS235 0,5 -- -- 5800 200 5800 200 (375 N/mm2) 0,63 -- -- 5800 200 5800 200
0,7 -- -- 5800 200 5800 200 0,75 -- -- 5800 200 5800 200 0,88 -- -- 5800 200 5800 200 1,0 -- -- 5800 200 5800 200
S355 0,4 -- -- 3400 340 4300 370
0,5 -- -- 4500 230 5000 200 -- --(530 N/mm2) 0,63 -- -- 6200 100 8400 190 0,7 -- -- 8400 190 8400 190 0,75 -- -- 8400 190 8400 190 0,88 -- -- 8400 190 8400 190 1,0 -- -- 8400 190 8400 190
Aluminium 0,4 -- -- 1800 280 2500 420 2800 230(230 N/mm2) 0,5 722 101 2100 270 2850 440 3200 600
0,6 -- -- 2400 255 3200 470 3600 2900,7 -- -- 2650 240 3500 500 3900 3200,8 2297 196 2950 230 3800 530 4900 3500,9 -- -- 3200 200 4150 560 4650 3851,0 -- -- 3500 200 4500 590 5000 4201,25 3000 82 -- -- --- -- --- --
Washer A10/12 Washer S16 Washer S19 Washer S22
Pull-over load Fu (N)
1 1
1
1
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Thickness in mm Washer S16 Washer S19 Washer A12
Shear load FQ (N)
Material Part I Part II x s x s x s
S235 0,63 0,75 2150 320 - -(375 N/mm2) 0,63 2x0,63 2430 370 2360 200 - -
0,63 1,5 3040 220 - -0,63 2,0 3580 200 - -0,63 2x1,25 2170 315 - -
0,75 2x0,75 3220 570 3190 330 - -0,75 1,5 4270 235 - -0,75 2x1,25 3770 320 - -1,0 1,0 3000 260 - -1,0 1,5 5020 610 - -1,0 2x1,0 4300 315 4380 140 - -1,0 2 4800 290 - -1,0 2x1,25 6140 780 - -1,25 1,25 - - - - 3792 2801,25 1,5 6160 435 - -
Alu 0,5 0,8 1200 100 1200 450 - -(230 N/mm2) 0,5 1,0 1500 170 1750 100 - -
0,5 2,0 1200 120 1800 200 - -0,8 2,0 2500 180 3000 150 - -1,0 1,0 2300 120 2000 450 - -1,0 2,0 3800 320 3800 300 - -
-
7/23/2019 SURUBURI AUTOFORANTE SFS
8/88
Technical value May/2006 sre/abjo
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Material Thickness (mm) x s
S235 (375 N/mm2) 0,75 905 1240,88 1131 1331,00 1194 731,25 1942 771,50 2691 952,00 4037 1242,50 5378 281
S355 (530 N/mm2) 0,75 1081 120
1,00 1864 961,25 2198 1211,50 3365 1602,00 5403 4502,50 7068 108
Pull out load FZ(N)
Part II (sub-construction)
SX5/SXL5
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 11227x = 8139
Material Part I Part II x s
S235 (375 N/mm2) 0,50 0,50 837 860,50 1,25 1533 1361,00 2,50 3623 320
S355 (530N/mm2) 0,50 1,25 1903 2331,00 2,50 5700 461
Thickness in mm washer S16
Shear load FQ (N)
Pull-over load Fu (N)
Material Thickness sheet part I (mm) x s
S235 0,50 4026 279(375 N/mm2) 0,63 5415 311
0,75 6972 2950,88 7694 5111,00 8930 448
Part II
Part I
MaterialFastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM EPDM
Size
Head / drive:hexagon, 8 mm A/F
SX55,5xL
SXL55,5xL
Shear load:
Figures obtained with displacement of3 mm between purlin and sheet.
Washer S16
-
7/23/2019 SURUBURI AUTOFORANTE SFS
9/88
Material Thickness (mm) x s
S235 2,0 2900 140(375 N/mm2) 2,5 4300 220
3,0 5600 3004,0 8500 4605,0 11500 6306,0 14100 800
S355 2,0 4200 210(530 N/mm2) 2,5 5500 310
3,0 6800 410
4,0 9200 6605,0 11700 8506,0 14200 1100
Alu 3,0 3600 220(230 N/mm2) 4,0 5300 350
5,0 6700 4706,0 8300 580
SX6
Admission SX6
SX6-L12
DIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
SizeHead/Drive:
- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive- D12 Head ( 12 mm) Torx T25
Pull-out load FZ(N)
Part II (Subconstruction)
SX6 5,5xL
SX6L12 5,5xL
SX6D12 5,5xL
Technical value April/2006 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 14000
x = 9500
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
10/88
Washer S16 Washer S19 Washer S22
Pull-over load Fu (N)
Material BlechdickePart I
(mm) x s x s x s
S235 0,4 3000 400 4200 270 (375 N/mm2) 0,5 4000 380 5100 300
0,63 5300 360 6200 340 0,7 6000 350 6800 360 0,75 6200 340 7200 380 0,88 7500 330 8400 410 1,0 8500 320 9500 440
S355 0,4 3200 440 3700 200 (530 N/mm2) 0,5 4300 520 5000 320 0,63 6200 620 7100 470 0,7 6900 650 7000 560 0,75 7300 680 8100 640 0,88 9000 750 9600 830 1,0 10600 800 10900 970
Alu 0,4 1200 90 1800 110 2300 480(230 N/mm2) 0,5 1500 110 2100 170 2800 470
0,6 1900 135 2600 230 3200 4600,7 2300 175 3100 290 3700 4500,8 2700 200 3500 355 4150 4400,9 3100 230 3900 420 4600 4301,0 3500 260 4300 480 5000 420
Part II
Part I
Thickness in mm Washer S16 Washer S19
Shear load FQ (N)
Material Part I Part II x s x s
S235 0,63 1,5 2300 240(375 N/mm2) 0,63 2,0 2800 100 2400 230
0,63 3,0 2600 2200,63 5,0 3200 50 2800 2100,63 6,0 3100 1900,75 1,5 3150 3400,75 2,0 2900 50 3200 3300,75 3,0 3300 3100,75 5,0 3250 50 3500 2700,75 6,0 3600 2500,88 2,0 4200 200 3700 3300,88 6,0 4300 50 4700 1601,0 1,5 4000 5001,0 2,0 4600 250 4200 4701,0 3,0 4400 4301,0 5,0 5000 320 4700 3401,0 6,0 5000 3001,25 1,5 4600 6001,25 3,0 5500 5501,25 5,0 65000 4801,5 1,5 5600 5001,5 5,0 8100 600
SX6
Technical value April/2006 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
11/88
Panele thickness (mm) 1,5 mm t 4 mm 4 mm t 12mm
SXC5 a(mm) SXC14 a(mm)40 4 3,260 6 4,380 8 5,7
St37
SXC
Admission SXC5
SXC14
DIBt Z-14.4-407
Material
Fastener SXC5:stainless steel A2, 18/8Material number 1.4301, AISI 304Fastener SXC14:stainless steel A2, 18/8Material number 1.4567Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDMSize
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive
Material Thickness (mm) x s
St37 (375 N/mm2) 1,5 2300 852,0 4000 1503,0 7200 1854,0 10280 1035
St37 (375 N/mm2) 4,0 10100 3405,0 12700 1015
Pull-over load Fu (N)
Type St37(375 N/mm2) Type AluminiumBlechdicke
Blechdicke
Part I(mm) x s Part I(mm) x s
SXC5 0,50 4150 500 SXC5 0,50 1370 1230,63 5100 650 0,63 1990 2600,75 7040 860 0,75 2150 238
0,88 7140 730 0,88 2700 3111,00 3350 285
SXC14 0,50 3700 382 SXC14 0,50 1410 1140,63 5100 535 0,63 1960 1240,75 6100 610 0,75 2290 175
0,88 2850 2051,00 3260 384
Part II
Part I
Max. deflection (mm)
Pull-out load FZ(N)
Part II (Subconstruction)
SXC5 5,5xL
SXC14 5,5xL
Technical value Februar/2004 sre/abjo
x = arithmetical mean values =Standard deviation
Type
SXC5
SXC14
Washer S19 Washer S19
Tensile breaking load Zb (N)
Shear breaking load Qb (N)
SXC5 x = 17500
SXC14 x = 14000
SXC5 x = 10900
SXC14 x = 12400
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
12/88
SXC, L 168 mm
Admission SXC14
DIBt Z-14.4-407
Material
Fastener SXC14:stainless steel A2, 18/8Material number 1.4567
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDMSize
Head/Drive:- Hex., 8 mm A/F
Material Thickness (mm) x s
St37 (375 N/mm2) 4,0 7350 6305,0 8800 10006,0 9810 1550
Pull-over load Fu (N)
Type St37(375 N/mm2) Type AluminiumThickness
Thickness
Part I(mm) x s Part I(mm) x s
SXC14 0,50 3700 382 SXC14 0,50 1410 114L 168 mm 0,63 5100 0,63 L 168 mm 0,63 1960 124
0,75 6100 610 0,75 2290 175
0,88 2850 2051,00 3260 384
Part II
Part I
Pull-out load FZ
(N)
Part II (Subconstruction)
SXC14 5,5x L 168
Technical value J anuar/2005 sre/pko
x = arithmetical mean values =Standard deviation
Type
SXC14-5,5 x 168 mm
Washer S19 Washer S19
Tensile breaking load Zb (N)
Shear breaking load Qb (N)
SXC14 L 168 mm x = 17700
SXC14 L 168 mm x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
13/88
Material Thickness (mm) x s
S235 (375 N/mm2) 4,0 10000 3655,0 11800 6306,0 12200 130
S355 (520 N/mm2) 4,0 8288 982(530 N/mm2) 5,0 9334 962(550 N/mm2) 6,0 11413 578
Alu (230 N/mm2) 4,0 4755 560
5,0 5300 400
SX14
Admission SX14
DIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8Material number 1.4567
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Part II (Subconstruction)
Thickness in mm Washer S16 Washer S19
Shear load FQ (N)
Material Part I Part II x s x s
S235 (375 N/mm2) 0,63 4,0 3136 168 - -0,75 4,0 3860 75 - -0,75 5,0 3800 100 - -
SX14 5,5xL
SX14-L12 5,5xL
Technical value April/2006 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displace-ment of 3 mm between purlin and sheet.
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 12000
x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
14/88
Wood 20 25 30 45 x s x s x s x s
SXW- 5,5 1700 190 2100 300 2500 200 SXW- 6,5 3600 210
SXW
Admission SXWDIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDMAlu, with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/Fbei SXW und SW-S
-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Part II (Subconstruction)
Washer S 16 Washer S 16 Washer S 16
Pull-over load Fu (N)
Material Thickness (mm) 0,5 0,5 0,75 0,75 0,88 0,88
x s x s x s
St37 SXW-S16-6,5x 4000 270 6200 7500 (375 N/mm2)
Alu SXW-S16-6,5x 1500 2700 3100 (230 N/mm2)
Part II
Part I
Shear load FQ (N)
Material Thickness (mm) 0,5 0,5 0,77 0,77 0,88 0,88
x s x s x s
St37 SXW-A14- 5,5 1800 130 2200 255 2500 370
(375 N/mm2) SXW-S16- 6,5 2400 3000 4900
Alu SXW-A14- 5,5 880 78 1500 85
(230 N/mm2) SXW-S16- 6,5 1200 2000
Embedment (mm)
SXW 5,5xL 6,5xL
SXW-L12 5,5xL 6,5xL
Technical value Oktober/2002 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
SXW 5,5 x = 14000SXW 6,5 x = 16000
SXW 5,5 x = 9500SXW 6,5 x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
15/88
Material x s
Wood Embedment 50 mm 5356 355
SXW 6,5
MaterialFastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDMAlu, with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F
Pull-out load FZ
(N)
Part II (Subconstruction)
Washer S 16 Washer S 19
Pull-over load Fu (N) Part II
Part I
SXW 6,5xL
Technical value August/2004 sre/abjo
x = arithmetical mean values =Standard deviation
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 17100
x = 12300
Material Thickness (mm) x s x s
St. 37 0,63 5460 369 6310 414
St. 37 0,75 6938 619 7535 576
Alu 1,00 4027 339 4685 443
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
16/88
Material Embedment (mm) x s
Timber 25 1625 10230 2030 53
Alu 2 mm 25 2360 31(240-280 N/mm2)
SW2-S
Pull-out load FZ(N)
Part II (Subconstruction)
SW2-S 4,8xL
Technical value September 2004 sre/pko
x = arithmetical mean values =Standard deviation
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 9234
x = 6653
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDMAlu, with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F
Washer A14
Pull-over load Fu (N) Teil II
Teil I
Material Thickness (mm) x s
St. 37 0,50 2260 150
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
17/88
Material Thickness (mm) x s
Wood 20 1790 39025 2190 27030 2840 160
Pull-out load FZ(N)
Part II (Subconstruction)
NK-A / SW-A
MaterialFastener:Alu
Washer:Alu, with vulcanized EPDM
SizeHead/Drive:Hex., 8 mm A/F
Washer A16
Pull-over load Fu (N)
Material ThicknessPart I
(mm) x s
Alu (230 N/mm2) 0,50 2140 190
Alu (230 N/mm2) 0,75 2450 170
Alu (230 N/mm2) 0,80 2840 -
Part II
Part I
Shear load FQ (N)
Thickness in mm Washer A16
Material Part I Part II x s
Wood/Alu 40 0,5 1460 100(230 N/mm2) 0,8 1700 120
NK-A 6,0xL
SW-A 6,0xL
Technical value Oktober/2002 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
NK-A x = 6500SW-A x = 6500
NK-A x = 4200
SW-A x = 4200
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
18/88
Admission SXL2
DIBt Z-14.1-4
Material
Fastener:
stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive
SXL2- 5,5
Pull-out load FZ(N)
Material Thickness (mm) x s
St37 0,40 573 36(375 N/mm2) 2x0,50 660 50
2x0,75 940 98
Part II (Subconstruction)
Material Part I Part II x s
St37 (375 N/mm2) 0,6 0,6 1400 129
Thickness in mm Washer S14
Shear load FQ (N)
SXL2 5,5xL
SXL2L12 5,5xL
Technical value Oktober/2002 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 14000
x = 9500
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
19/88
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F- L12 Head ( 12 mm) iriusDrive
SXL2- 6,3
Pull-out load FZ(N)
Material Dicke (mm) x s
St37 0,62 1166 30(375 N/mm2) 0,75 1563 76
Bauteil II (Unterkonstruktion)
Material Part I Part II x s
St37 (375 N/mm2) 1,0 1,0 3940 195
Thickness in mm Washer S16
Shear load FQ (N)
SXL2 6,3xL
SXL2L12 6,3xL
Technical value J anuary 2006 sre/abjo
Shear breaking load Qb (N)
x = 13500
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
WasherS16
Pull-over load Fu (N)
Material Sheet thicknessPart I
(mm) x s
St37 (375 N/mm2) 0,62 4980 314
Part II
Part I
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
20/88
Material Part I Part II x s
Alu 0,4 0,4 400 500,7 0,7 910 110
Thickness in mm Washer A14
Material
Fastener:Aluminium
Washer:Aluminium, with vulcanized EPDM
SizeHead/Drive:Hex., 8 mm A/F
Material Part I Part II x s
Alu (230 N/mm2) 0,4 0,4 400 500,7 0,7 910 110
SL2-A
Pull-out load FZ(N)
Material Thickness (mm) x s
Alu (230 N/mm2) 2x0,7 550 35
Part II (Subconstruction)
Shear load FQ (N)
Technical value Oktober/2002 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb
(N)
x = 5000
x = 3500
SL2-A 5,5xL
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
21/88
Material Sheet thickness (mm) Pre drill Embedment (mm) (mm) x s x s
Alu 3,0 4,50 3400 52
St37 0,75 4,50 1091 33 - -(375 N/mm2) 1,00 4,50 2290 - - -
1,50 4,50 2745 81 - -1,50 5,05 4070 - - -2,00 5,05 5400 - - -2,50 5,05 7920 - - -3,00 5,05 9750 - - -
Wood 25 4,80 2320 - - -30 4,80 3360 - - -
40 4,80 4170 - - -50 4,80 5720 - - -
TDA-S
Admission TDA-S
DIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8
Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F Washer S16 Washer S19
Pull-over load Fu (N)
Material BlechdickePart I
(mm) x s x s
St37 0,5 4060 5145
(375 N/mm2) 0,63 5500 6560 0,75 5920 6805 0,88 7720 9010 1,00 8490 9900
Part II
Part I
Shear load FQ (N)
Pull-out load FZ(N)
Part II (Subconstruction)
Material Part I (mm) Part II (mm)1,0 mm 1,5 mm 3,0 mm
x x x
St37 0 63 3210 3410 4060(375 N/mm2) 0,75 4520 4800 5420
1,00 5040 6410 70901,25 5100 8930 87801,50 5130 11280 -
Technical value J uly/2005 sre/abjo
TDA-S 6,5xL
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Tensile breaking load Zb (N)
x = 16000
Shear breaking load Qb (N)
x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
22/88
TDB-S
Admission TDB-S
DIBt Z-14.1-4
Material
Fastener:stainless steel A2, 18/8
Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) Pre drill (mm) x sS235 2,00 4,90 3880 5(375 N/mm2) 4,00 5,35 14090 51
5,00 5,65 17590 706,00 5,80 16140 278,00 5,80 20660 59
S355 1,25 5,05 3016 100(510 N/mm2) 1,50 5,35 3419 118(500 N/mm2) 2,00 5,35 5327 162
Part II (Subconstruction)
Washer S16 Washer S19
Pull-over load Fu (N)
Material BlechdickePart I (mm) x s x s
S235 (375 N/mm2) 0,50 4060 5145 0,63 5500 6560 0,75 5920 6805 0,88 7720 9010 1,00 8490 9900
S355 (340N/mm2) 0,50 4771 190 --
(355N/mm2) 0,63 6029 414 --
Part II
Part I
Shear load FQ (N)
Material Part I Part II x s Part II x s
St37 0,75 4570 4590
(375 N/mm2
) 0,88 6520 6250 1,00 4,0 6740 8,0 7280 1,25 11270 11220 1,50
Thickness in mm
Technical value May/2006 sre/abjo
TDB-S 6,3xL
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Tensile breakingload Zb (N)
x = 16000
Shear breakingload Qb (N)
x = 12500
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
23/88
TDC-S
MaterialFastener:
stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F
Pull-out load FZ(N)
Part II (Subconstruction)
Material Thickness (mm) Pre drill x s
S355 (530 N/mm2) 0,4 4,0 580 231,0 4,0 2860 100
S355 (530 N/mm2) 1,5 4,9 4210 1003,0 4,9 9500 155
Alu PE300 2,0 5,3 2490 140(230 N/mm2) 3,0 5,3 4780 56
4,0 5,3 6600 1075,0 5,6 9030 320
6,0 5,6 12000 280
TDC-S 6,3xL
Shear load FQ (N)
Material Part I Part II x s Part II x s
S235 0,63 3210 3410 (375 N/mm2) 0,75 4520 4800
1,00 1,0 5040 1,5 6410 1,25 5100 8930 1,50 5130 11280
0,63 4060 -0,75 5420 -1,00 3,0 7090 -1,25 8780 -1,50 *
Thickness in mm
Technical value May/2006 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
24/88
SD2-S
Material
Fastener:stainless steel A4,Material number 1.4567, AISI 316
Abmasse
Head / Drive:- Hex. , 8 mm A/F
SD2-S 6,0xL
Technical value Februar 2003 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 12675
x = 19153
Pull-out load FZ(N)
Material Thickness (mm) x s
St37 0,75 1748 50(375 N/mm2) 1,00 2255 72
Teil II (Subconstruction)
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
25/88
SD2-T
SD2-T 6,3xL
Technical value J uni 2003 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb
(N)
x = 22000
x = 13500
Pull-out load FZ
(N)
Material Thickness (mm) x s
St37 0,88 1970 120(375 N/mm2) 1,50 3800 230
Teil II (Subconstruction)
x = arithmetical mean values =Standard deviation
Material
Fastener:Carbon steel withcorrosion protected surface
Washer:Steel with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Washer T15 Washer T19
Pull-over load Fu (N)
Material BlechdickePart I
(mm) x s x s
St37 0,50 4950 400 - -(375 N/mm2) 0,63 5620 350 - -
Part II
Part I
Shear load FQ (N)
Material Teil 1 (mm) Teil 2 (mm) x s
St37 0,75 0,75 2983 384(375 N/mm2) 0,75 1,00 4050 172
0,75 1,25 4709 1790,75 2,00 5379 416
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
26/88
SD3 4,8
Material Thickness Part I (mm) x s x s x s
S235 0,50 -- -- 4950 - 5450 -(375 N/mm2) 0,63 -- -- 5620 - 6020 -
0,75 -- -- 7100 - 7200 -0,88 -- -- 7600 - 7800 -1,00 -- -- 8400 - 8600 -
S355 (570 (N/mm2) 0,50 4473 358 3822 431 - -
(390 (N/mm2) 0,63 5861 343 5554 273 - -(410 (N/mm2) 0,75 -- -- 6760 399 - -(410 (N/mm2) 0,88 -- -- 8048 237 - -(375 (N/mm2) 1,00 -- -- 9291 323 - -
SD3 4,8xL
Technical value April 2006 sre/abjo
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 22000x = 13500
Pull-out load FZ(N)
Material Thickness (mm) x sS235 (375 N/mm2) 1,00 1350 - -
1,50 2170 - -2,00 3160 - -3,00 5790 - -
S355 (410 N/mm2) 0,88 1220 69(520 N/mm2) 1,00 2000 69(510 N/mm2) 1,50 3323 103(500 N/mm2) 2,00 5225 167(560 N/mm2) 3,00 9132 150
Part II (Subconstruction)
x = arithmetical mean values =Standard deviation
Material
Fastener:Carbon steel with
corrosion protected surface
Washer:Steel with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Washer T15Washer A14
Pull-over load Fu (N) Part II
Part I
Shear load FQ (N)
Material Washer Part I (mm) Part II (mm) x s
St37 T15 0,75 2,00 6140 - -(375 N/mm2) T19 1,00 2,00 6980 - -
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Washer T19
-
7/23/2019 SURUBURI AUTOFORANTE SFS
27/88
SD3 5,5-6,3
Material
Fastener:Carbon steel withcorrosion protected surface
Washer:Steel with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Part II (Subconstruction)
Shear load FQ (N)
Material Washer Part I Part II x
(mm) (mm)4,8 St37 T15 0,75 2,00 6140
(375 N/mm2) T19 1,00 2,00 6980
5,5 St.37 T15 0,63 2,00 3500(375 N/mm2) T19 1,00 2,00 6800
Type Material Thickness (mm) x s
5,5 S235 1,50 3750 -
(375 N/mm2) 2,00 5000 -
3,00 7500 -6,3 S235 0,88 1970 -
(375 N/mm2) 1,00 3330 -1,50 5000 -
2,00 5000 -
3,00 7500 -
5,5 S355 1,50 3690 112
(510 N/mm2) 2,00 6330 135
(550 N/mm2
) 3,00 9922 244
SD3 5,5xL 6,3xL
Technical value May/2006 sre/abjo
Shear breakingload Qb (N)
Tensile breaking load Zb (N)
5,5 x = 16000 6,3 x = 22000
5,5 x = 10000 6,3 x = 13500
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Material Thickness Part I (mm) x s x s x s
S235 0,50 -- -- 4950 - 5450 -(375 N/mm2) 0,63 -- -- 5620 - 6020 -
0,75 -- -- 7100 - 7200 -
0,88 -- -- 7600 - 7800 -1,00 -- -- 8400 - 8600 -S355 (570 (N/mm2) 0,40 -- -- 3360 400 - -
(390 (N/mm2) 0,63 -- -- 5620 350 - -(410 (N/mm2) 0,75 -- -- 7100 460 - -(410 (N/mm2) 0,88 -- -- 7600 510 - -
1,00 -- -- 8400 590 -- -
Washer T15Washer A14
Pull-over load Fu (N) Part II
Part I
Washer T19
-
7/23/2019 SURUBURI AUTOFORANTE SFS
28/88
SD3 - D10
Material
Fastener:Carbon steel withcorrosion protected surface
Washer:
Carbon steel
Size
Head/Drive:- Lens head., 8 mm- T25
Pull-out load FZ(N)
Part II (Subconstruction)
Pull-over load Fu (N) Part II
Part I
Shear load FQ (N)
Material Washer Thickness (mm)x s
-- 0,62
Material Washer Part I Part II x s(mm) (mm)
S235 (375 N/mm2) T19 0,62 1,25 2863 370
S235 (375 N/mm2)
Material Sheet thickness mm x s
S235 (375 N/mm2) 1,25 2019 146
1,50 2584 154
S235 (360/mm2) 1,50 2791 150
SD3-D10-T19/C9 5,5xL
Technical value April/2005 abjo/sre
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
1 =Pull-over load fail in Part II, see Fz value
1 1
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 10000
-
7/23/2019 SURUBURI AUTOFORANTE SFS
29/88
SD5
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 1,50 2650 118(375 N/mm2) 2,00 3400 170
3,00 6300 3804,00 9300 6505,00 11500 920
S355 (510 N/mm2) 1,50 2940 173(500 N/mm2) 2,00 4990 342(560 N/mm2) 3,00 9550 516(520 N/mm2) 4,00 13100 750
Part II (Subconstruction)
Washer T16 Washer T19
Pull-over load Fu (N)
Material TicknessPart I (mm) x s x s
S235 (375 N/mm2) 0,50 4950 400 5450 4400,63 5620 350 6020 3800,75 7100 460 7200 4700,88 7600 510 7800 5301,00 8400 590 8600 600
S355 (570 N/mm2) 0,50 3360 400 -- --(390 N/mm2)) 0,63 5620 350 -- --(410 N/mm2)) 0,75 7100 460 -- --(410 N/mm2)) 0,88 7600 510 -- --(435 N/mm2)) 1,00 8400 590 -- --
Part II
Part I
Shear load FQ (N)
Thickness in mm Washer T16
Material Part I Part II x s
St37 (375 N/mm2) 0,63 2,00 3500 4200,75 3,00 5400 6501,00 2,00 6800 8201,00 3,00 7300 8801,50 2,00 10600 12701,50 3,00 10800 1300
Technical value April/2006 sre/abjo
SD5 5,5xL
SD5-L12 5,5xL
Shear breaking load
Qb (N)Tensile breaking load
Zb (N)
x = 15470 x = 10000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Washer T15
-
7/23/2019 SURUBURI AUTOFORANTE SFS
30/88
SD5-H15
Admission SD5-H15
DIBt Z-14.1-4
Material
Fastener:Carbon steel 18B3with corrosion protected surfaeSize
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 (375 N/mm2) 1,50 2795 1472,00 3987 96
S355 (510 N/mm2) 1,50 3920 99(500 N/mm2) 2,00 6180 270(500 N/mm2) 3,00 10250 400(520 N/mm2) 4,0 15400 480
Part II (Subconstruction)
Pull-over load Fu (N)
Material ThicknessPart I
(mm) x s
S235 0,63 5732 288(375 N/mm2) 0,75 7508 515
Part II
Part I
Shear load FQ (N)
Material Part I Part II x s
St37 0,63 1,50 3179 225(375 N/mm2) 1,25 3,00 7644 330
Thickness inmm
Technical value April/2006 sre/abjo
SD5-H15 5,5xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 15900
x = 10000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
31/88
SD6
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 3,00 6480 320(375 N/mm2) 4,00 12200 732
5,00 16600 11606,00 21000 1680
S355 (560N/mm2) 3,00 10800 500(520N/mm2) 4,00 15450 540(530N/mm2) 5,00 20940 450(550N/mm2) 6,00 22720 420
Part II (Subconstruction)
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,75 6,00 4790 5800,88 6,00 5300 6401,00 6,00 6870 8201,50 6,00 10760 1290
Thickness in mm Washer T16
Technical value March/2006 sre/abjo
Shear breakingload Qb (N)
Tensile breaking load Zb (N)
x = 22000x = 13500
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
SD6 6,3xL
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Washer T16 Washer T19
Pull-over load Fu (N)
Material TicknessPart I (mm) x s x s
S235 (375 N/mm2) 0,50 4950 400 5450 4400,63 5620 350 6020 3800,75 7100 460 7200 4700,88 7600 510 7800 5301,00 8400 590 8600 600
S355 (570 N/mm2) 0,50 3360 400 -- --(390 N/mm2)) 0,63 5620 350 -- --(410 N/mm2)) 0,75 7100 460 -- --(410 N/mm2)) 0,88 7600 510 -- --(435 N/mm2)) 1,00 8400 590 -- --
Part II
Part I
Washer T15
-
7/23/2019 SURUBURI AUTOFORANTE SFS
32/88
SD8
MaterialFastener:Carbon steel 18B3 withcorrosion protected surface
SizeHead/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 2,00 3200 170(375 N/mm2) 3,00 6200 380
4,00 8800 6506,00 12500 920
S355 (500 N/mm2) 2,00 4690 240(560 N/mm2) 3,00 9200 300(520 N/mm2) 4,00 12240 640(550 N/mm2) 6,00 15620 1320
Part II (Subconstruction)
Material Thickness (mm) Washer x s
S235 (375 N/mm2) 0,50 T15 4950 -0,63 5620 -0,75 7100 -0,88 7600 -1,00 8400 -0,50 T19 5450 -0,63 6020 -0,75 7200 -0,88 7800 -
1,00 8600 -S355 (570 N/mm2) 0,40 T15 3490 440
(390 N/mm2) 0,63 5460 380(410 N/mm2) 0,75 6700 300(410 N/mm2) 0,88 7710 335(410 N/mm2) 1,00 9220 130
Pull-over load Fu (N) Part II
Part I
Shear load FQ (N)
Material Part I Part II x s
St37 0,63 2,00 3300 420(375 N/mm2) 0,75 3,00 4200 650
1,00 2,00 4400 8201,00 3,00 5800 8801,50 2,00 6200 12701,50 3,00 7600 1300
Thickness in mm Washer T15
Technical value May/2006 sre/abjo
SD8-L12 5,5xL
SD8 5,5xL
Shear breakingload Qb (N)
Tensile breaking load Zb (N)
x = 15800x = 12000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
33/88
Thickness in mm
SD8-H15
Admission SD8-H15
DIBt Z-14.1-4
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 2,00 3200 170(375 N/mm2) 3,00 6200 380
4,00 8800 6506,00 12500 920
S355 (500 N/mm2) 2,00 4690 240(560 N/mm2) 3,00 9200 300(520 N/mm2) 4,00 12240 640(550 N/mm2) 6,00 15620 1320
Part II (Subconstruction)
Pull-over load Fu (N)
Material Sheet thicknessPart I (mm) x s
S235 0,63 3700 320(375 N/mm2) 0,75 6200 400
0,88 8300 5601,00 9000 630
S235 0,50 5142 280(340 N/mm2) 0,63 6544 304
Part II
Part I
Shear load FQ (N)
Material Part I Part II x s
St37 0,63 2,00 3300 420(375 N/mm2) 0,75 3,00 4200 650
1,00 2,00 4400 820
1,00 3,00 5800 8801,50 2,00 6200 12701,50 3,00 7600 1300
Technical value March/2006 sre/abjo
SD8-H15 5,5xL
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 15800x = 12000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
34/88
SD14
Material
Fastener:Carbon steel 18B3
Washer:Carbon steel 18B3with vulcanizedEPDM
Size
Head/ Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
S235 4,00 8959 726(375 N/mm2) 5,00 10914 1299
8,00 12040 -10,00 12040 -
S355 (520 N/mm2) 4,00 12150 380(530 N/mm2) 5,00 16000 310(550 N/mm2) 6,00 16900 480(460 N/mm2) 8,00 16700 460
Part II (support)
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,63 2,00 3300 4200,75 3,00 4200 6501,00 2,00 4400 8201,00 3,00 5800 8801,50 2,00 6200 12701,50 3,00 7600 1300
Thickness in mm Washer T16
Technical value March/2006 sre/abjo
SD14 5,5xL
Shear breaking load Qb (N) Tensile breaking load Zb (N)
x = 12040x = 9826
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Washer T16 Washer T19
Pull-over load Fu (N)
Material Thickness Part I(mm) x s x s
S235 0,50 4950 400 5450 440(375 N/mm2) 0,63 5620 350 6020 380
0,75 7100 460 7200 4700,88 7600 510 7800 5301,00 8400 590 8600 600
S355 (570 N/mm2
) 0,40 3490 440 -- --(390 N/mm2) 0,63 5460 380 -- --(410 N/mm2) 0,75 6700 300 -- --(410 N/mm2) 0,88 7710 335 -- --(410 N/mm2) 1,00 9220 130 -- --
Part II
Part I
Washer T15
-
7/23/2019 SURUBURI AUTOFORANTE SFS
35/88
SD14 - H15
Material
Fastener:Carbon steel 18B3
Size
Head/ Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
St37 4,00 8959 726(375 N/mm2) 5,00 10914 1299
6,00 12040 ---8,00 12040 ---
S355 (520 N/mm2) 4,00 12150 380(530 N/mm2) 5,00 16000 310(550 N/mm2) 6,00 16900 480
(460 N/mm2) 8,00 16700 460
Part II (support)
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,63 4,00 4293 4120,75 5,00 5374 411
0,88 5,00 6632 512
Thickness in mm
Technical value May/2006 sre/abjo
SD14-H15 5,5xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 12040
x = 9826
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin and
sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
36/88
SDC2-L12
Material
Fastener:Carbon steel 18B3, withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanizedEPDM
Size
Head/ Drive:-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Washer A16
Pull over load Fu (N)
Material Sheet thickness Part I (mm) x s
St37 0,63 3374 182(375 N/mm2) 0,75 4317 263
0,88 4539 184
Part II
Part I
Technical value September/2004 sre/pko
SDC2-L12 5,5xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 10000
x = arithmetical mean values =Standard deviation
Material Part I Part II x s
St37 (375 N/mm2) 0,63 0,63 2225 840,75 0,75 2648 1290,88 0,88 2929 1081,00 1,00 3060 1411,25 1,25 4831 255
Thickness in mm Washer A 16
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Part II (support)
-
7/23/2019 SURUBURI AUTOFORANTE SFS
37/88
SDL3
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanizedEPDM
Size
Head/ Drive:-L12 Head ( 12 mm) iriusDrive
Pull-out load FZ(N)
Washer T15
Pull-over load Fu
(N)
Material Blechdicke Teil I (mm) x s
St37 0,50 4950 -(375 N/mm2) 0,63 5620 -
0,75 7100 -0,88 7600 -1,00 8400 -
Part II
Part I
Technical value Oktober/2002 sre/abjo
SDL3-L12 5,5xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 10000
x = arithmetical mean values =Standard deviation
Material Part I Part II x s
St37 (375 N/mm2) 0,50 0,55 934 -0,75 1,25 2783 -0,75 0,75 1525 -0,75 1,50 3566 -
Thickness in mm Washer T15
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Part II (support)
-
7/23/2019 SURUBURI AUTOFORANTE SFS
38/88
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanizedEPDM
Size
Head/ Drive:Hex., 8 mm A/F
SDT5
Material Thickness Part I (mm) x s
S355 (570 N/mm2) 0,40 4890 490(390 N/mm2) 0,63 5650 500
S320 (410 N/mm2) 0,75 7100 670
S355 (570 N/mm2) 0,40 4790 790
(390 N/mm2) 0,63 6090 690S320 (410 N/mm2) 0,75 8540 550
Technical value
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 16000x = 10000
SDT5 5,5xL
x = arithmetical mean values =Standard deviation
March 2006 pko/sre
Pull-over load Fu
(N) Part II
Part I
Washer A19
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Pull-out load FZ(N)
Material x sS235 (375 N/mm2) 1,50 2800 170
(355 N/mm2) 2,00 4120 165(375 N/mm2) 3,00 6300 380(375 N/mm2) 4,00 9300 650
S355 (510 N/mm2) 1,50 3313 150S355 (500 N/mm2) 2,00 5280 200S355 (560 N/mm2) 3,00 10140 600S355 (520 N/mm2) 4,00 14200 420
Thickness in mm Washer A19
Washer S19
40 2,5S235(375 N/mm2) 50 3,0
60 3,6
70 4,390 5,5
Panel thickness (mm) SDT5 / SDTP5 Deflection a (mm)
Deflection gem.ECCS
Part II (support)
-
7/23/2019 SURUBURI AUTOFORANTE SFS
39/88
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanizedEPDM
Size
Head/ Drive:
Hex., 8 mm A/F
SDT14
Material Thickness Part I (mm) x s
S355 (570 N/mm2) 0,40 4900 370(390 N/mm2) 0,63 5680 250
S355 (570 N/mm2) 0,40 5100 470
(390 N/mm2
) 0,63 6480 520
Technical value
SDT14 5,5xL
x = arithmetical mean values =Standard deviation
March 2006 pko/sre
Pull-over load Fu
(N) Part II
Part I
Washer A19
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Pull-out load FZ(N)
Material x sS235 (375 N/mm2) 4,00 10170 670S235 (375 N/mm2) 5,00 10820 910S235 (375 N/mm2) 8,00 11150 540
S355 (520 N/mm2) 4,00 9939 743S355 (530 N/mm2) 5,00 10958 758S355 (550 N/mm2) 6,00 10958 758.
Thickness in mm Washer A19
Washer S19
I-Purlin / 10 mm 40 2,5S235(375 N/mm2) 50 3,0
60 3,670 4,390 5,5
Panel thickness (mm) SDT14 /SDTP14 Deflection a (mm)
Deflection gem. ECCS
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 16000x = 10000
Part II (support)
-
7/23/2019 SURUBURI AUTOFORANTE SFS
40/88
Material
Fastener:Carbon steel 18B3
with corrosion protected surfae
Size
Head/Drive:Hex. (WH11), 11 mm A/F
SDP3
Pull-out load FZ(N)
Material Thickness (mm) x s
St52 (530 N/mm2) 1,50 4028 2362,00 6270 3722,50 8363 1853,00 10430 477
Part II (Subconstruction)
Technical value
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 10000
SDP-3 5,5xL
x = arithmetical mean values =Standard deviation
Februar 2003 abjo/sre
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
41/88
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Aluminiumwith vulcanizedEPDM
Size
Head/ Drive:Hex., 8 mm A/F
SDP6
Material Thickness Part I (mm) x s
St37 (375 N/mm2) 0,50 3092 830,63 4047 880,75 5039 1590,88 5709 1961,00 6331 118
Technical value
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 16000
x = 10000
SDP-6 5,5xL
x = arithmetical mean values =Standard deviation
August 2003 abjo/sre
Pull-over load Fu
(N) Part II
Part I
Flange 10 mm
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
42/88
Material
Fastener:Carbon steel 18B3 withkorrosionsgeschzter Oberflche
Washer:Aluminiumwith aufvulkanisiertem EPDM
SizeHead/ Drive:Hex., 8 mm A/F
SDTW
Pull-out load FZ
(N)
Material Embedment (mm) x s
Timber wood 35 3141 743
Part II (Subconstruction)
Technical value
Shear breaking load Qb
(N)
Tensile breaking load Zb (N)
x = 20000
x = 12000
SDTW 6,5xL
Februar 2003 abjo/sre
x = arithmetical mean values =Standard deviation
Washer A19
Pull-over load Fu
(N)
Material Thickness (mm) x sSt37 0,50 2140 -(375 N/mm2) 0,63 5000 -
0,75 6200 -
Part II
Part I
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
43/88
SW-T
Material
Fastener:Carbon steel 18B3
Washer:Aluminiumwith vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ
(N)
Material Embedment x s
4,8 Wood 20 mm 1700 44525 mm 2030 28030 mm 2260 150
6,5 Wood 20 mm 1900 12025 mm 2300 14030 mm 3000 18045 mm 4810 245
Part II (Subconstruction)
Washer A14
Pull-over load Fu
(N)
Material BlechdickePart I
(mm) x s
4,8 St37 (375 N/mm2) 0,50 2260 1500,70 2260 150
6,5 St37 (375 N/mm2) 0,50 3000 1100,75 3000 110
Diese Werte wurden bei voll eingeschraubten Befestigern ermittelt. Die Pull-out load Fz sindzu bercksichtigen.
Part II
Part I
Shear load FQ (N)
Material/Part II Part I x s
4,8 St37/Wood 0,50 1530 75(375 N/mm2) 0,75 1600 135
6,5 St37/Wood 0,50 1860 170(375 N/mm2) 0,75 1690 220
Thickness in mm Washer A14
Technical value
SW-T 4,8xL 6,5xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
4,8 x = 10700 6,5 x = 21500
4,8 x = 6700 6,5 x = 12800
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
Mrz/2003 sre/abjo
Part II
Part I
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
44/88
SL2-T
Admission SL2-T
DIBt Z-14.1-4
Material
Fastener:Carbon steel 18B3
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ
(N)
Material Thickness (mm) x s
St37 (375 N/mm2) 2x0,63 1180 602x0,75 1310 64
Alu PE 300 2x1,00 2360 49
Alu F 25 2x0,6 610 452x0,70 820 45
Part II (Subconstruction)
Thickness in mm
Shear load FQ
(N)
Material Part I Part II x s
St37 (375 N/mm2) 0,63 0,63 1820 210
Alu PE 300 1,00 1,00 1950 88
Technical value Mrz/2003 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 10000
x = 6300
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
SL2-T 4,8xL
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
45/88
SL2-H15
Admission SL2-H15
DIBt Z-14.1-4
Material
Fastener:Carbon steel 18B3
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ
(N)
Material Thickness (mm) x s
S235 (375 N/mm2) 2x0,75 1360 -2x1,00 1990 -
S355 (490 N/mm2) 2x0,75 1689 119(520 N/mm2) 2x1,00 2579 120
Part II (Subconstruction)
Thickness in mm
Shear load FQ
(N)
Material Part I Part II x s
S235 (375 N/mm2) 0,75 0,75 3380 -1,00 1,00 4800 -
Technical value May/2006 sre/abjo
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 20000
x = 12000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
SL2-H15 6,3xL
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
46/88
Thickness in mm
Material Part I Part II x s
S235 (375 N/mm2) 0,75 1,25 2651 215
0,75 1,50 2957 109
0,88 1,25 2898 1240,88 1,50 3228 157
1,50 1,50 6900 830
SL3-H15
Material
Fastener:
Carbon steel 18B3
Washer:
without
Size
Head/Drive:
Hex., 8 mm A/F
Pull-out load F
Z
(N)
Shear load FQ (N)
Technical value J une/2006 sre/abjo
SL3-H15 6,3xL
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 20000
x = 12000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin and
sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Thickness in mm
Material Part I Part II x s
S235 (375 N/mm2) 0,75 1,25 1986 89
0,75 1,50 2896 80
1,50 1,50 3200 190
S355 (510 N/mm2) 1,25 1,25 2874 250
1,50 1,50 3873 297
Part II
Part I
-
7/23/2019 SURUBURI AUTOFORANTE SFS
47/88
SL2-S-4,8x22
Material
Fastener:stainless steel A2, 18/8Material number, AISI 304
Washer:stainless steel A2, 18/8Material number, AISI 304,with vulcanized EPDMundAluminiumwith vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) x s
St37 (290 N/mm2) 0,40 525 222x0,50 682 272x0,63 1015 712x0,75 1171 612X1,00 1687 57
Alu (265 N/mm2) 2x0,75 548 148
Part II (Subconstruction)
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,63 0,63 1524 64
Technical value May 2005 sre/abjo
SL2-S 4,8x22
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 9800
x = 5900
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displa-cement of 3 mm between purlin and sheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
48/88
SL3-F
Material
Fastener:Carbon steel 18B3Oberflche:
gelb zinced
Size
Head/Drive:- Vierkant, Schlsselweite 6 mm
Pull-out load FZ
(N)
Part II (Subconstruction)
Shear load FQ (N)
Part II Thickness in mmSt. 37 x
Part ISt. 37 (375 N/mm2) 0,7 1,0 1,2 1,5 2,0
0,7 mm 2100 2600 2950 3400 4200
1,0 mm 2600 3100 3400 3850 -
1,2 mm 2950 3400 3700 4200 -
Material Thickness in mmSt. 37 x
Part ISt. 37 (375 N/mm2) 0,7 1,0 1,2 1,5 2,0
0,7 mm 830 1100 1100 1100 1500
1,0 mm 550 550 550 550 -
1,2 mm 550 550 550 550 -
Technical value Oktober/2002 sre/abjo
SL3-F 4,2x15
Shear breaking load Qb (N)
Tensile breaking load Zb
(N)
x = 6730
x = 5140
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-
placement of 3 mm between purlin andsheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
49/88
SL4-F
Material
Fastener:Carbon steel 18B3Surface:blue zinced
Size
Head/Drive:- Square, 6 mm A/F
Pull-out load FZ
(N)
Part II (Subconstruction)
Shear load FQ (N)
Part II Thickness in mmSt. 37 x
Part ISt. 37 (375 N/mm2) 0,7 1,0 1,2 1,5 2,0
1,0 mm - - - - 4650
1,2 mm - - - 4200 4960
1,5 mm NA NA 4200 4960 5430
2,0 mm 4200 4650 4960 5430 6200
NA =not applicably
Material Thickness in mmSt. 37 x
Part ISt. 37 (375 N/mm2) 0,7 1,0 1,2 1,5 2,0
1,0 mm - - - - 2700
1,2 mm - - - 2200 2200
1,5 mm NA NA 1900 1900 1900
2,0 mm 800 1000 1000 1000 1000
NA =not applicably
Technical value Oktober/2002 sre/abjo
SL4-F 4,8x16
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 6730
x = 7770
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
50/88
TDA-T
Material
Fastener:Carbon steel 18B3with korrosionsgesctzter Oberflche
Washer:Carbon steel 18B3with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Technical value May/2006 sre/abjo
x = arithmetical mean values =Standard deviation
TDA-T 6,5xL
Material Sheet thickness (mm) Pre drill Embedment (mm) (mm) x s x s
Alu 3,0 4,50 3400 52
St37 0,75 4,50 1091 33 - -(375 N/mm2) 1,50 4,50 2745 81 - -
4,50 4,50 2290 - - -1,50 5,052,00 5,05 - - 5400 -
2,50 5,05 - - 7920 -3,00 5,05 - - 9750 -
Wood 25 4,80 - 232030 4,8 3360 40 4,80 - - 4170 -50 4,80 - - 5720 -
Washer S16 Washer S19
Pull-over load Fu
(N)
Material Part I
(mm) x s x s
S235 (375 N/mm2) 0,50 4060 5145 0,63 5500 6560 0,75 5920 6805 0,88 7720 9010 1,00 8490 9900
S355 (340 N/mm2) 0,50 4771 190 -- (355 N/mm2) 0,63 6029 414 --
Part II
Part I
Pull-out load FZ(N)
Part II (Subconstruction)
Tensile breaking load Zb (N)
x = 16000
Shear breaking load Qb
(N)
x = 12000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
51/88
TDA-T
Technical value May/2006 sre/abjo
x = arithmetical mean values =Standard deviation
Shear load FQ (N)
Material Part I Part II x s(mm) (mm)
St37 (375 N/mm2) 0,63 1,00 3210 -1,50 3410 -3,00 4060 -
0,75 1,00 4520 -1,50 4800 -3,00 5420 -
1,00 1,00 5040 -
1,50 6410 -3,00 7090 -1,25 1,00 5100 -
1,50 8930 -3,00 8780 -
1,50 1,00 5130 -1,50 11280 -
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
52/88
TDB-T/TDC-T
Material
Fastener:Carbon steel 18B3 withcorrosion protected surface
Washer:Carbon steel 18B3with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F
Pull-out load FZ(N)
Material Thickness (mm) Pre drill x s
S235 2,00 5,35 5200 (375 N/mm2) 2,50 5,35 7530
4,00 5,65 12050 5,00 5,65 15642 6,00 5,65 17310 8,00 5,80 20424
S355 1,25 5,05 3016 100(510 N/mm2) 1,50 5,35 3419 118(500 N/mm2) 2,00 5,35 5327 162
Part II (Subconstruction)
Washer S16 Washer S19
Pull-over load Fu (N)
Material ThicknessPart I
(mm) x s x s
St37 0,50 4060 5145 (375 N/mm2) 0,63 5500 6560
0,75 5920 6805 0,88 7720 9010 1,00 8490 9900
S355(340N/mm2) 0,50 4771 190 -- (355N/mm2) 0,63 6029 414 --
Part II
Part I
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,75 4,00 4570
8,00 4590 0,88 4,00 6520
8,00 6250 1,00 4,00 6740
8,00 7280 1,25 4,00 11270
8,00 11220
Thickness in mm
Technical value May/ 2006 sre/abjo
TDB-T 6,3xL
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
Shear breakingload Qb (N)
Tensile breakingload Zb (N)
x = 21000x = 13000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
53/88
TDBL
Material
Fastener:Carbon steel , material number 17B2DIN 1.5502
Size
Head/Drive:- Hex., 13 mm A/F
Pull-out load FZ(N)
Material Thickness mm Pre drill mm x s
steel S355 0,90 7,5 1440 761,00 6,5x10,5 2750 601,25 7,5 5160 150
steel S235 10,00 8,0 29400 1000
Part II (Subconstruction)
Shear load FQ (N)
Material Part I Part II Pre-drill mm x s
steel S355 0,90 0,90 7,5 3400 2901,00 1,00 7,5 4500 2902,00 2,00 7,5 15600 390
Thickness in mm
Technical value May / 2006 sre/hch
TDBL 8,6xL
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with displace-ment of 3 mm between purlin and sheet.
Product information
Hole size:
- Components t < 1,25 mm in steel S235 or S355, pre-drilled with 7,5 mm or 6,5 x 10,5 mm slot- Components t < 3 mm, pre-drilled with 7,5 mm- Components t 3 mm,pre-drilled with 8,0 mm
Shear breaking load Qb (N)
x = > 26000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Part I
Part II
-
7/23/2019 SURUBURI AUTOFORANTE SFS
54/88
Type Material Thickness (mm) x / Klip with 2 Fastener s
SDK2-S St37 0,63 1327 37(375 N/mm2) 0,75 3740 327
1,00 5290 3171,25 6730 327
Alu 0,90 2210 2091,20 3480 2131,80 5610 144
SDK-S
Certified in the perm9issions the crease
roofs manufacturer
Material
Fastener:stainless steel A2, 18/8
Size
Head/Drive:Special square
Pull-out load FZ
(N)
Part II (Subconstruction)
Type Material Thickness (mm) x / Klip with 2 Fastener s
SDK3-S St37 1,50 6070 295(375 N/mm2) 1,75 6770 197
2,00 7840 1452,50 9370 3803,00 11650 495
Alu 1,80 5100 1802,00 6052 3602,50 8300 2203,00 10880 260
SDK2 6,0xL
SDK3 6,0xL
Technical value
x = arithmetical mean values =Standard deviation
Shear breaking load Qb
(N)
Tensile breaking load Zb (N)
x = 11000
x = 7500
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
May 2005 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
55/88
Thickness in mm Washer S16
SXW
Admission SXW
DIBt Z-14.1-4
Material
Fastener:stainless steel 1.4301
Washer:stainless steel 1.4301with vulcanized EPDM
Size
Head/Drive:Hex., 8 mm A/F
Pull-out load FZ
(N)
Material Embedment (mm) x s
20 1760 190Wood 25 2170 300
30 2570 200
Part II (Subconstruction)
Washer S16
Pull-over load Fu
(N)
Material ThicknessPart I
(mm) x s
St 37 0,50 4000 (375 N/mm2) 0,75 6200
0,88 7500
Alu 0,50 1500 0,75 2700 0,88 3100
Part II
Part I
Shear load FQ (N)
Material Part I Part II x s
St37 (375 N/mm2) 0,50 1870 130Wood 0,75 2280 250
0,87 2580 370
Aluminium (230 N/mm2) 0,50 880 78Wood 0,77 1500 85
Technical value Oktober/2002 sre/abjo
SXW 6,5xL
SXW-L12 6,5xL
Shear breaking load Qb
(N)
Tensile breaking load Z
b
(N)
x = 16000
x = 12000
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
56/88
Material Thickness (mm) x s Pre drill mm
Alu PE300 1/2h 1,00 1674 47Alu PE300 1/2h 1,25 1906 34 5.35Alu 1,80 2060 25
St37 (375 N/mm2) 0,50 1362 280,75 1990 55 5,351,20 2140 80
RV6604
Admission RV6604
DIBt Z-14.1-4
Material
Sleeve:AIMg5Mandrel:AICuMg1
Size
Shank: 5,2 mmMandrel: 2,8 mmBund: 11,5 mm
Pull-out load FZ
(N)
Part II (Subconstruction)
FQ
FQ
Material Part I Part II x s
Aluminium (230 N/mm2) 1,80 1,80 3020 235
St37 (375 N/mm2) 0,75 0,75 2050 44
Thickness in mm
Shear load FQ (N)
Technical value August/2003 sre/hch
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 2050
x = 3300
Shear load: Figures obtained with
displacement of 3 mm between purlinand sheet.
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
57/88
Material Thickness (mm) x s Pre drill mm
Alu 0,70 2300 - 7,90
St37 (375 N/mm2) 0,55 3120 - 7,90
RV6603
Material
Sleeve:AIMg5
Mandrel:AICuMg1
SizeShank: 7,8 mmMandrel: 4,4 mmBund: 15,7 mm
Pull-out load FZ
(N)
Part II (Subconstruction)
Technical value August/2003 sre/hch
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 5000
x = 6800
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
58/88
Part II (Subconstruction)
SXC
Admission SXC5
DIBt Z-14.4-407
Material
Fastener:stainless steel A2, 18/8Material number 1.4301, AISI 304
Washer:stainless steel A2, 18/8
Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) irius Drive
Material Thickness (mm) x s
St37 (375 N/mm2) 1,5 2300 852,0 4000 1503,0 7200 1854,0 10280 1035
Washer S16 Washer S19 Washer S22
Pull-over load Fu
(N)
Material BlechdickePart I
(mm) x s x s x s
St37 0,50 4100 495 4200 500 3900 255(375 N/mm2) 0,62 4800 345 5100 655 5100 265
0,75 6300 540 7000 865 0,87 6600 530 7100 735
Alu 0,50 1400 185 1300 125 1400 140(230 N/mm2) 0,65 1900 175 1900 260 1900 185
0,70 2400 240 2100 240 2200 2250,80 2400 240 2700 310 1,00 3300 290 3500 315
Part II
Part I
Max. deflection (mm)
Material a (mm)
St37 (375 N/mm2) 40 460 680 8
Panelendicke (mm) 1,5 mm t 4 mm
Pull-out load FZ
(N)
SXC5 5,5xL
Technical value Oktober/2002 sre/abjo
Shear breaking load Qb
(N)
Tensile breaking load Zb (N)
x = 17500
x = 10900
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
59/88
SXCW
Admission SXCW
DIBt Z-14.4-407
Material
Fastener:stainless steel A2, 18/8Material number, AISI 304
Washer:stainless steel A2, 18/8Material number 1.4301, AISI 304with vulcanized EPDM
Size
Head/Drive:- Hex., 8 mm A/F-L12 Head ( 12 mm) irius Drive
Pull-out load FZ
(N)
Material Embedment (mm) x s
Timber 50 5800 585Leimbinder 50 6500 325
Part II (Subconstruction)
Washer S16 Washer S19 Washer S22
Pull-over load Fu
(N)
Material BlechdickePart I
(mm) x s x s x s
St37 0,50 4100 280 4200 280 4100 560(375 N/mm2) 0,62 5100 225 5700 510 6400 650Alu 0,50 1300 120 1200 100 1000 180(230 N/mm2) 0,62 1600 300 1400 95 1300 170
Part II
Part I
SXCW 6,5xL
Technical value Oktober/2002 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 17500
x = 10900
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
60/88
Type Material Embedment (mm) x s
SCFW Timber 38 2700 -45 3830 49 4500 -53 5700 --
SCFW
Pull-out load FZ
(N)
Part II (Subconstruction)
Admission SCFW
DIBt Z-31.1-47, 31.1-137
Z-31.1-52, 31.1-142
Z-31.1-128, 31.1-130
MaterialFastener:SCFW: Carbon steel, hot dip galvanisedSCFW-S: Material number 1.4301, AISI 304
Washer:BAZstainless steel A2with vulcanisedEPDM
Size
Head/Drive:Hex., 8 mm A/F
Washer:BAZ 25 mm
Technical value November/2005 sre/abjo
SCFW 6,5xL
Shear breaking load Qb
(N)
Tensile breaking load Zb
(N)
x = 21150
x = 11000
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
61/88
Material
Fastener:SCFW-S: stainless steel A2Material number 1.4301, AISI 304
Washer: A12Aluminiumwith vulcanisedEPDM
Size
Head: 10 mmDrive:T20W
Washer:A12 12 mm
Type Material Embedment (mm) x s
SCFW-S Timber 30 1790 145
SCFW-S
Pull-out load FZ
(N)
Part II (Subconstruction)
Technical value Oktober/2002 sre/abjo
SCFW 5,0xL
x = arithmetical mean values =Standard deviation
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 7000
x = 5000
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
62/88
Type Material Thickness (mm) x s
SCF3 St37 1,5 3120 125(375 N/mm2) 3,0 6300 340
SCF12 St37 3,0 6220 440(375 N/mm2)
SCF3/SCF12
Material
Fastener:
Carbon steel 18B3
Washer: BAZstainless steel A2with vulcanised EPDM
Size
Head/Drive:Hex.,8 mm A/F
Washer:BAZ 25 mm
Pull-out load FZ(N)
Part II (Subconstruction)
SCF3 6,3xL
SCF12 6,3xL
Technical value
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 21150
x = 11000
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Oktober/2002 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
63/88
TT/TTN
Test certificate ETB
Material
Fastener:stainless steel A2Material number 1.4301
Washer:stainless steel withaufvulkanisiertem EPDM
Sleeve TTN:AlMg5
Size
Schraube:TT-S-D12-5xLHead: 12Innenangriff:T20
Washer:Sleeve TTN-A-D16 16 mm
Pull-out load FZ(N)
Material Embedment (mm) x s
TTN-A-D16 4,0 4600 400
6,0 8800 450
Part II (Subconstruction)
TT TTN
Technical value
x = arithmetical mean values =Standard deviation
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 10200
x = 6290
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Oktober/2002 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
64/88
FQ
FQ
Thickness in mm
Fz
ASO
Material
Sleeve:Aluminium AlMg3
Mandrel:stainless steel A3Material number 1.4541
Size
Shank: 4,0/4,8 mm
Head:
8,0/9,5 mm
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pre drill- mm
ASO St37 (375 N/mm2) 0,75 1260 56 4,8 mm
Part II (Subconstruction)
Shear load FQ (N)
Type Material Part I Part II x s
ASO Alu (230 N/mm2) 1,8 1,8 2020 40 4,8 mm
St37 (375 N/mm2) 0,75 0,75 2337 1620,75 3,0 1820 60
Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
ZbZ
b
Qb
Qb
4,9
Technical value Oktober/2004 sre/abjo
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
4,0 x = 1420 4,8 x = 1950
4,0 x = 1120 4,8 x = 1480
ASO 4,8xL
x = arithmetical mean values =Standard deviation
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
65/88
FQ
FQ
Thickness in mm
Fz
ASO-D11/D14
Material
Sleeve:Aluminium AlMg3
Mandrel:stainless steel A3Material number 1.4541
Size
Shank: 5,0 mm
Head:
11/14 mm
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pre drill- mm
ASO St37 (375 N/mm2)
Part II (Subconstruction)
Shear load FQ (N)
Type Material Part I Part II x s
ZbZ
b
Qb
Qb
5,1
Technical value Oktober/2004 sre/hch
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = 2500
x = 1650
ASO 5,0xL
x = arithmetical mean values =Standard deviation
Shear load Figures obtained with displacement of 3 mm Part I und
Part II
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
66/88
FQ
FQ
Thickness in mm
Fz
ASC
Admission ASC
DIBt Z-14.1-4
Material
Sleeve:AlMg5Mandrel:stainless steel A3Material number 1.4541
Size
Shank: 4,8 mmHead: 9,5 mm
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pre drill- mm
ASC Alu (230 N/mm2) 1,80 2350 120 4,8 m
Alu (230 N/mm2) 3,00 3020 125
ASC St37 (375 N/mm2) 0,75 1130 80 4,8 mm
1,20 2170 105
Part II (Subconstruction)
Shear load FQ (N)
Type Material Part I Part II x s
ASC Alu 1,8 4,00 2700 85 4,8 mm
(230 N/mm2)
ASC St37 0,75 5,00 2650 85 4,8 mm
(375 N/mm2
)
4,9
Technical value Oktober/2002 sre/abjo
ASC 4,8xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-
placement of 3 mm between purlin andsheet.
ZbZ
b
Qb
Qb
4,8 x = 3400
4,8 x = 2400
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
67/88
AAC
Material
Sleeve:EN AW-1050 AMandrel:Al
Size
Shank: 4,8 mmHead: 9,5 mmMandrel: 2,7 mmPredrill:
4,9 mm
Technical value May/2006 sre/abjo
AAC 4,8xL
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = arithmetical mean values =Standard deviation
ZbZ
b
Qb
Qb
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
1000
1400
-
7/23/2019 SURUBURI AUTOFORANTE SFS
68/88
Thickness in mm
FQ
FQ
ATO
MaterialSleeve:ATO AIMg3Mandrel:ATO Carbon steel zinced
Size
Shank: 4,8 mmHead: 9,5 mm
Fz
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pre drill- (mm)
ATO 4,8 mm Alu (230 N/mm2) 1,80 2140 55 4,9
Part II (Subconstruction)
Shear load FQ(N)
Type Material Part I Part II x s
ATO Alu 1,80 4,00 1950 85 4,8 mm
St37 0,75 4,00 1820 65
Technical value Oktober/2004 sre/abjo
ATO 4,8xL
(230 N/mm2)
(315 N/mm2)
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-
placement of 3 mm between purlin andsheet.
ZbZ
b
Qb
Qb
4,8 mm x = 1950 5,0 mm x = 2955
4,8 mm x = 1480 5,0 mm x = 1858
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
-
7/23/2019 SURUBURI AUTOFORANTE SFS
69/88
FQ
FQ
ATC
Admission ATC (only 4,8 mm)
DIBt Z-14.1-4
Material
Sleeve:Aluminium AIMg5Mandrel:Carbon steel
Size
Shank: 3,2/4,0/4,8 mmHead: 6,5/8,0/9,5 mm
Fz
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pre drill- (mm)
ATC Alu 1,80 1340 95 3,3 3,2 mm
Alu 3,00 1335 140 3,3
ATC Alu ,80 2010 70 4,1 4,0 mm
Alu 3,00 2250 130 4,1
ATC Alu 1,80 2510 85 4,9 4,8 mm
Alu 3,00 3250 190 4,9
ATC St37 0,75 880 35 3,3 3,2 mm
St37 1,20 1300 52 3,3
ATC St37 0,75 1050 55 4,1 4,0 mm
St37 1,20 1850 85 4,1
ATC St37 0,75 1240 70 4,9 4,8 mm
St37 1,20 2330 190 4,9
Part II (Subconstruction)
Thickness in mm
Shear load FQ(N)
Type Material Part I Part II x s
ATC St37 0,75 3,00 1300 85 3,2 mm
ATC St37 0,75 4,00 1970 100 4,0 mm
ATC St37 0,75 8,00 2530 84 4,8 mm
Technical value
ATC div.xL
(230 N/mm2)
(230 N/mm2)
(230 N/mm2)
(230 N/mm2)
(230 N/mm2)
(230 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
(375 N/mm2)
Shear breaking load Qb (N)
Tensile breaking load Zb (N)
x = arithmetical mean values =Standard deviation
Shear load: Figures obtained with dis-placement of 3 mm between purlin andsheet.
ZbZ
b
Qb
Qb
3,2 x = 1350 4,0 x = 2500 4,8 x = 3400
3,2 x = 1100
4,0 x = 1650 4,8 x = 2400
All stated values are x values, representing the arithmetical mean value from laboratorytesting concluded up to now, appropriate safety margins should be applied for fieldconditions. Consult also your countrys approval documents.
Oktober/2002 sre/abjo
-
7/23/2019 SURUBURI AUTOFORANTE SFS
70/88
FQ
FQ
Thickness in mm
TTO
MaterialSleeve:TTO Steel zincedMaterial number 1.0303Mandrel:TTO Carbon steel zinced
SizeShank: 3,2/4,8 mmHead: 6,5/9,5 mm
Fz
Pull-out load FZ(N)
Type Material Thickness (mm) x s Pr