sunrise telecom ssmtt 48 (udsl) manual

SUNRISE TELECOM

SSMTT-48UDSL Module for the MTT PlatformUsers Manual SA948MAN-22523-001 Rev. C00

ule Mod U D S L T T- 4 8 SSM

1

www.sunrisetelecom.com

WARNING

Using the supplied equipment in a manner not specified by Sunrise Telecom may impair the protection provided by the equipment.CAUTIONS

Donotremoveorinsertthemodulewhilethetestsetison.Insertingorremovingamodulewiththepoweronmay damage the module and or chassis. Donotremoveorinsertthesoftwarecartridgewhilethetestsetison.Otherwise,damagecouldoccurtothecartridge. End of Life Recycling and Disposal Information DONOTdisposeofWasteElectricalandElectronicEquipment(WEEE)asunsortedmunicipalwaste.ForproperdisposalreturntheproducttoSunriseTelecom.Pleasecontactourlocalofficesorservicecentersforinformationonhow toarrangethereturnandrecyclingofanyofourproducts. EC Directive on Waste Electrical and Electronic Equipment (WEEE) The Waste Electrical and Electronic Equipment Directive aims to minimize the impact of the disposal of electrical and electronic equipment on the environment. It encourages and sets criteria for the collection, treatment, recycling, recovery, and disposal of waste electrical and electronic equipment..

2011SunriseTelecomIncorporated.Allrightsreserved. Disclaimer:Contentssubjecttochangewithoutnoticeandarenotguaranteedforaccuracy.2 SSMTT-48 UDSL Module

SSMTT-48 UDSL Module Users Manual Table of Contents1 UDSL Module ............................................................................................................................................................ 5 1.1 Module Connector Panel ............................................................................................................... 5 1.2LEDs ............................................................................................................................................. 5 1.3ScreenIndicators........................................................................................................................... 6 2 UDSL Menus ............................................................................................................................................................. 7 2.1 Modem Control .............................................................................................................................. 8 2.1.1 Modem Setup ................................................................................................................. 8 2.1.2EndShowtime .............................................................................................................. 11 2.1.3InitiateHandshake ....................................................................................................... 11 2.2 Modem Status ............................................................................................................................. 12 2.2.1 Current Status .............................................................................................................. 12 2.2.2ErrorMeasurements.................................................................................................... 13 2.2.3 Tone Graphic/Table ..................................................................................................... 14 2.2.3.1 Bits Per Tone ............................................................................................................ 14 2.2.3.2SNRPerTone .......................................................................................................... 15 2.2.4EventTracer ................................................................................................................ 16 2.3IPDataFeatures(SoftwareOption) ............................................................................................ 17 2.3.1IPConfiguration ........................................................................................................... 17 2.3.1.1IPDSL-ATMConfiguration ........................................................................................ 18 2.3.1.2IPDSL-PTMConfiguration........................................................................................ 20 2.3.1.310/100EthernetConfiguration .................................................................................. 21 2.3.1.4EnteringaUserID/Password.................................................................................... 21 2.3.2IPStatus ...................................................................................................................... 22 2.3.2.1DHCPIPStatus ........................................................................................................ 22 2.3.2.2StaticIPStatus ......................................................................................................... 22 2.3.2.3PPPDynamicIPStatus ............................................................................................ 23 2.3.3 Ping Test ...................................................................................................................... 23 2.3.4TraceRoute ................................................................................................................. 25 2.3.5WebAccessTest ......................................................................................................... 26 2.3.5.1HTTPDownloadTest ................................................................................................ 26 2.3.5.2FTPDownloadTest .................................................................................................. 26 2.3.5.3FTPUploadTest....................................................................................................... 27 2.3.6IPDataPassThroughMode ....................................................................................... 28 2.4IPVideoFeatures(SoftwareOption) .......................................................................................... 29 2.4.1IPConfiguration ........................................................................................................... 29 2.4.1.1IPTypeStaticConfiguration ......................................................................................30 2.4.1.2IPTypeDHCPConfiguration .................................................................................... 32 2.4.1.3 DSL PPP Configuration .............................................................................................34 2.4.1.4VODConfiguration .................................................................................................... 35 2.4.1.5VODURLListScreen ...............................................................................................36 2.4.1.6 Test Template Creation ............................................................................................. 37 2.4.1.7EPGChannelTableCreation ....................................................................................38 2.4.2IPStatus ...................................................................................................................... 39 2.4.3VideoStreamTests ..................................................................................................... 40 2.4.3.1 Stream Configuration ................................................................................................ 40 2.4.3.2 TSRates ................................................................................................................... 41 2.4.3.3 TS Measurements .................................................................................................... 41 2.4.3.4 PIDMAPAnalysis..................................................................................................... 41 2.4.3.5 Channel Test............................................................................................................. 42 2.4.3.6MDIMeasurements .................................................................................................. 423

2.4.4VODTest ..................................................................................................................... 43 2.4.4.1 Describe Media ......................................................................................................... 43 2.4.4.2 Play Media ................................................................................................................ 43 2.5VOIPFeatures(SoftwareOption) ............................................................................................... 45 2.5.1IPConfiguration ........................................................................................................... 45 2.5.2IPStatus ......................................................................................................................45 2.5.3 Protocol Setup ............................................................................................................. 45 2.5.4Place/ReceiveCalls .................................................................................................... 48 2.5.5VQMeasurements....................................................................................................... 51 2.5.5.1Non-intrusiveVQMMeasurement ............................................................................ 51 2.5.5.1.1Non-intrusiveReportScreens ................................................................................ 51 2.5.5.2 Terminated Call Metrics Screen ............................................................................... 52 2.6View/Store/Print .......................................................................................................................... 53 2.6.1 Saving a Test ............................................................................................................... 53 2.6.2RenamingaStoredTest .............................................................................................. 53 2.6.3ViewingaStoredTest .................................................................................................. 54 2.6.4 Printing a Stored Test .................................................................................................. 54 2.6.5 Deleting a Stored Test ................................................................................................. 54 2.6.6LockingandUnlockingaStoredTest .......................................................................... 54 2.7 Profiles ......................................................................................................................................... 55 2.8 Utility ............................................................................................................................................ 56 2.8.1ModuleInformation ...................................................................................................... 56 2.8.2UpdateSoftware.......................................................................................................... 56 3 Application Overview............................................................................................................................................. 57 3.1 Testing a DSL Line....................................................................................................................... 57 3.2IPTVApplications ........................................................................................................................ 58 3.2.1STBEmulationatDSLInterface .................................................................................. 58 3.2.2STBEmulationattheEthernetInterface ..................................................................... 58 3.3VODApplications ........................................................................................................................ 59 3.3.1STBEmulationatDSLInterface .................................................................................. 59 3.3.2STBEmulationattheEthernetInterface ..................................................................... 59 3.4VoIPApplications ........................................................................................................................60 3.4.1PlacingorReceivinganH.323Call .............................................................................60 3.4.2H.323PhoneCallwithoutaGatekeeper ..................................................................... 60 3.4.3H.323PhoneCallwithaGatekeeper .......................................................................... 61 3.4.4H.323PhoneCalltoaPSTN(POTS)Device .............................................................. 61 3.4.5PlacingorReceivingaSIPCall ................................................................................... 62 3.4.6Non-IntrusiveVoiceQualityMeasurement .................................................................. 62 4 General Information ...............................................................................................................................................63 4.1 Testing and Calibration Statement ............................................................................................... 63 4.2 Customer Service ........................................................................................................................ 63 4.3Offices ......................................................................................................................................... 63 4.4ExpressLimitedWarranty ...........................................................................................................64 Index .............................................................................................................................................................................65

4

SSMTT-48 UDSL Module

1 UDSL ModuleTheUDSLmodulesupportsbothVDSLxandADSLxmodes.Testingapplicationsinclude CPEemulation,COemulation,andIPservicestesting.

1.1 Module Connector Panel

UDSL

10/100

Figure 1 UDSL Module Connector Panel TheUDSLmodulecontainsthefollowingports: UDSL:ThisisanRJ-45DSLlineinterface. 10/100:ThisporttheEthernetinterface.TheportcontainstwoLEDs.ThegreenLEDindicatesEthernetlinklevelconnectivity,theyellowLEDindicatestraffic.

1.2 LEDsMODULE DMM SIGNAL FRAME ERRORS HOLD xTU-C TDR/RFL LP 1 SYNC AIS BPV/CODE RESPOND xTU-R LINE LP 2 SYNC ALARM PAT SYNC BIT ERR POWER BATTERY SIGNAL FRAME ERRORS HOLD LP 1 SYNC AIS BPV/CODE RESPOND LP 2 SYNC ALARM PAT SYNC BIT ERR MODULE xTU-C xTU-R POWER BATTERY

SunSet MTT ACM II

SunSet MTT

SSMTT-ACM, -ACM+, and -ACM II SSMTT-B, -C Figure 2 Test Set LED Panels ThefollowingLEDsshowninFigure2areusedbytheUDSLmodule: MODULE: The module is active. xTU-C:COmode. Red:WAITINGstate. BlinkingRed:TRAININGstate. Green:SHOWTIMEstate. Alternateblinkingredandgreen:ThemodemlosesSHOWTIME,retrains,andre-achieves SHOWTIME.PressHISTORYtoclear. xTU-R:CPEmode. Red:WAITINGstate. BlinkingRed:TRAININGstate. Green:SHOWTIMEstate. Alternateblinkingredandgreen:ModemlosesSHOWTIME,retrains,andreachieves SHOWTIME.PressHISTORYtoclear. ERRORS:Alocal(near-endorreceived)eventthattriggersalocalerrorsecondinthe ERRORMEASUREMENTSscreen. Red:Currenterror. Blinking red: An error has occurred, but it is no longer present. Press HISTORY to clear.

1- UDSL Module

5

1.3 Screen IndicatorsThescreenindicatesthestatusoftheUDSLmodule 11:50:45 ontheupperlinesunderthetimeofday.Theleftside >SHOWTIME CPE MODE:VDSL2 on the second line can indicate: VDSL2 PROFILE:12a WAITING TRAINING CURRENT STATUS SHOWTIME DOWNSTREAM UPSTREAM LINKDOWN:PressRETRAIN(F3)whenyou RATE:95000 kbps RATE:42384 kbps MAX :97000 kbps MAX :43542 kbps see this state. See Section 2.1.1fordetails. CPTY:98 % CPTY:98 % Thetestsetcanalsodisplayontheleftsideofthe SNRM:6.5 dB SNRM:6.5 dB ATTN:7.0 dB ATTN:7.0 dB thirdandfourthlines: PATH:INTL PATH:INTL CPE MODE/CO MODE: Indicates the selected RETRAIN STORE MODEMTYPEandDSLmode.SeeSection 2.1.1 fordetails. Figure 3 Screen Indictors PROFILE:DisplaystheVDSL2serviceprofile.This isnotapplicableforADSLxorVDSL1modes. ThesecondlineontherightsideofthescreencanindicateIPconnectionstatus(IP,PPP, orDHCP).Anexample: IP...:Connectionisinprogress. IPUP:connectionismade. IPDOWN:connectionisnotmade. Blank:IPnotinuse.

6


2 UDSL MenusPressthechassisMODULEkeytoaccesstheUDSLmodulemainmenu. MODULE Key UDSL MAIN MENU MODEM CONTROL MODEM STATUS IP DATA FEATURES IP VIDEO FEATURES VOIP FEATURES VIEW/STORE/PRINT PROFILES UTILITY MODEM CONTROL 2.1.1 MODEM SETUP 2.1.2 END SHOWTIME 2.1.3 INITIATE HANDSHAKE

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8

MODEM STATUS 2.2.1 2.2.2 2.2.3 2.2.4 CURRENT STATUS ERROR MEASUREMENTS TONE GRAPHIC/TABLE EVENT TRACER

TONE GRAPHICS/TABLE UTILITY 2.8.1 MODULE INFORMATION 2.8.2 UPDATE SOFTWARE IP DATA FEATURES 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 IP CONFIGURATION IP STATUS PING TEST TRACE ROUTE WEB ACCESS TEST 2.2.3.1 BITS PER TONE 2.2.3.2 SNR PER TONE

VOIP FEATURES 2.5.1 2.5.2 2.5.3 2.5.4 2.5.5 IP CONFIGURATION IP STATUS PROTOCOL SETUP CALL FEATURES VQ MEASUREMENTS

IP VIDEO FEATURES 2.4.1 2.4.2 2.4.3 2.4.4 IP CONFIGURATION IP STATUS VIDEO STREAM TESTS VOD TEST

VIDEO STREAM TESTS 2.4.3.1 2.4.3.2 2.4.3.3 2.4.3.4 2.4.3.5 2.4.3.6 STREAM CONFIGURATION TS RATES TS MEASUREMENTS PID ANALYSIS CHANNEL TEST MDI TEST

VOD TEST 2.4.4.1 DESCRIBE MEDIA 2.4.4.2 PLAY MEDIA

Note: Depending on ordered options and/or configuration setup, some menu items may not appear in the menu selection screens. Figure 4 UDSL Menu Tree

2 UDSL Module Menus

7

2.1 Modem ControlThis menu contains: MODEMSETUP ENDSHOWTIME INITIATEHANDSHAKE 2.1.1 Modem Setup Configurethefollowing: MODEM TYPE Options:CPE(F1),CO(F2) ThemodemcanbesetupasaCPE(CustomerPremisesEquipment)orasaCO(Central Office).COisanoptionalfeature. TheremainderofthescreenisdependentontheMODEMTYPEselected,refertothefollowingtwosubsectionsandconfiguretherestofthesettings: CPE Setup11:50:45 >WAITING CPE MODE:N/A VDSL PROFILE:N/A MODEM SETUP MODEM TYPE:CPE DSL MODE :VDSLx STANDARD :VDSL2/POTS WAITING CPE MODE:N/A VDSL PROFILE:N/A MODEM SETUP MODEM TYPE:CPE DSL MODE :ADSLx STANDARD :ADSLx MULTI ANX-A WAITING VDSLx STANDARD 1:VDSL2/POTS 2:VDSL2/ISDN 3:VDSL2 IKAN-CO4-EU 4:VDSL2 CNXT-NA1 5:VDSL2 IKAN-CO4-NA1 6:VDSL2 IKAN-CO4-NA2 7:VDSL2 IKAN-CO5-NA-30a 8:VDSL1 CNXT-NA1 9: 10: SELECT

WAITING ADSLx STANDARD 1:ADSLx MULTI ANX-A 2:ADSLx MULTI ANX-B 3:ADSLx SIEMENS-ANX-B 4:ADSL2/2+ ANNEX M 5: 6: 7: 8: 9: 10: SELECT

WAITING CPE MODE:N/A VDSL PROFILE:N/A MODEM SETUP

WAITING CPE MODE:N/A VDSL PROFILE:N/A MODEM SETUP MODEM TYPE:CO DSL MODE :ADSLx STANDARD :ADSLx MULTI ANX-A

WAITING 1:VDSL2 2:VDSL2 3:VDSL2 4:VDSL2 5:VDSL2 6:VDSL2 7:VDSL1 8: 9: 10: SELECT VDSLx STANDARD 12a ANX-A 17a ANX-B/B8-12 30a ANX-A 30a ANX-C IKAN-EU-12a CNXT-NA1-8d CNXT-NA1-8a

11:50:45 >WAITING ADSLx STANDARD 1:ADSLx MULTI ANX-A 2:ADSLx MULTI ANX-B 3:ADSL2/2+ ANX M 4: 5: 6: 7: 8: 9: 10: SELECT

Figure 6 CO Modem Setup Screens InadditiontotheMODEMTYPEsetting,theMODEMSETUPscreens,shownatthetop ofFigure6containthefollowingsettings: DSL MODE Options:VDSLx(F1),ADSLx(F2) Selectthetypeofmodeminuse.Iftheselectionisnotavailable,thescreenwilldisplay OPTIONISNOTENABLED. VDSLx:VeryhighspeedDigitalSubscriberLine;xreferstothestandardsavailablein thelowerleftscreenshowninFigure6. ADSLx:AsymmetricDigitalSubscriberLine;xreferstothestandardsavailableinthe lowerrightscreenshowninFigure6. STANDARD AccessthelowerscreensinFigure6,viaSELECT(F1).SeeTables3and4foradescriptionofeachstandard.Use or tohighlightastandardandpressSELECT(F1)toreturn totheMODEMSETUPscreen.ThechoiceisdisplayedontheSTANDARDline. PressRETRAIN(F3)whenreadytostarttheinitiationandconnecttothefarendCPE device.AsuccessfulinitiationwillconsistofthetestsetdisplayingTRAINING,followed bySHOWTIMEalongwiththeLEDindicationsdescribedinSection 1.2. Standard ADSLxMULTIANX-A ADSLxMULTIANX-B ADSL2/2+ANXM Description MostcommonworldwideADSLxoverPOTSAnnexAsystem. CommonADSLxoverISDNAnnexBsystem.Thisismainly deployedinEurope. ADSL2/ADSL2systemsupportingAnnexMmode. Table 3 CO/ADSLx Standards Standard VDSL212aANX-A10

Description VDSL2AnnexAusingprofile12a.SSMTT-48 UDSL Module

VDSL217aANX-B/B8-12 VDSL230aANX-A VDSL230aANX-C VDSL2IKAN-EU-12a VDSL2CNXT-NA1-8d VDSL1CNXT-NA1-8a

VDSL2AnnexBusingprofile17a. VDSL2AnnexAusingprofile30a. VDSL2AnnexCusingprofile30a. IkanosCPE-4basedmodemusingprofile12a.Thisis mainlydeployedinEurope. Conexantbasedmodemusingprofile8d.Thisismainly deployedinNorthAmerica. ConexantbasedmodemusingVDSL1profile8a.Thisis mainlydeployedinNorthAmerica. Table 4 CO/VDSLx Standards

2.1.2 End Showtime Whenfinishedtesting,closethelink: 1. Selectfromthemodulemainmenu,MODEMCONTROL>ENDSHOWTIME. 2. Followtheon-screeninstructions,andpressENTER. 3. ThescreendisplaysCLOSINGLINKandCOMPLETEwhenfinished.Alsonotethat thetopmessageshowsWAITINGattheendoftheprocess. 4. Whenfinished,pressESC. Note:Itisgoodpracticetomanuallyclosethelinkinsteadofjustunpluggingfromthesignal. Whenyouclosethelink,thetestsetsendsaCloseCommandmessagetotheDSLAM. TheDSLAMthenknowswhythesignalislostwhenthetestsetisdisconnected. 2.1.3 Initiate Handshake Thetestsetautomaticallyinitiateshandshakewiththefarendmodemuponpoweringup. However,ifthelinkneedstobereopened,selectthisitem. 1. Selectfromthemodulemainmenu,MODEMCONTROL>INITIATEHANDSHAKE. 2. Followtheon-screeninstructions,andpressENTER. 3. ThescreendisplaysTRAINING.Thetoplefton-screenmessagedisplaysWAITING followedbyTRAINING.ThexTU-C(COmode)orxTU-R(CPEmode)LEDshouldbe blinkingred,indicatingthetestsetistryingtoconnect. 4. Ifthereisasuccessfulconnection,theCURRENTSTATUSscreenisdisplayed.The toplefton-screenmessagedisplaysSHOWTIMEandthexTU-C(COmode)orxTUR(CPEmode)LEDisgreen.Ifunsuccessful,TRAININGisdisplayedandthexTU-C (COmode)orxTU-R(CPEmode)LEDcontinuesblinkingred.

2 UDSL Module Menus

11

2.2 Modem StatusThis menu contains: CURRENTSTATUS ERRORMEASUREMENTS TONEGRAPHIC/TABLE EVENTTRACER 2.2.1 Current Status11:50:45 >SHOWTIME CPE MODE:VDSL2 VDSL2 PROFILE:17a CURRENT STATUS DOWNSTREAM RATE:95000 kbps MAX :97000 kbps CPTY:98 % SNRM:6.5 dB ATTN:7.0 dB PATH:INTL UPSTREAM RATE:42384 kbps MAX :43542 kbps CPTY:97 % SNRM:6.5 dB ATTN:7.0 dB PATH:INTL RETRAIN STORE11:50:45 >SHOWTIME CPE MODE:ADSL2+ANNEX A VDSL2 PROFILE:N/A CURRENT STATUS DOWNSTREAM DELY:1 ms INP :0.8 DEPH:1 frm PWR :11.0 dBm UPSTREAM DELY:1 ms INP :0.8 DEPH:8 frm PWR :11.8 dBm

FAR END VENDOR ID: BDCM RETRAIN STORE

Figure 7 Current Status Screens TheleftCURRENTSTATUSscreeninFigure7reportsthefollowinginformationforboth DOWNSTREAMandUPSTREAM: RATE:CurrentratereportedinkbpsorMbps. MAX:MaximumattainableratereportedinkbpsorMbps. CPTY:CapacityisapercentageratioofLineRate/MaximumRate.Acommonindustry thresholdforcapacityisameasurementoflessthan85%forastableline. SNRM:Signal-to-NoiseRatioMarginindB.Acommonindustrythresholdisaminimum SNRMof8.0dBforastableline. ATTN:AttenuationindB. PATH:Thisshowsthelatencypath;INTL(Interleaved)ifthedelayis> /=2ms,orFASTif thedelayisbetween01ms. Press toviewtherightCURRENTSTATUSscreenshowninFigure7.ItreportsthefollowinginformationforbothDOWNSTREAMandUPSTREAM(exceptFARENDVENDOR): DELY: Actual Interleaver Delay reported in ms (millisecond). The delay ranges from 163mS.Theinterleaverdelayissettomeetthenetworkserviceprovidersrequirements forerrorburstprotectionandlatency. INP:ActualImpulseNoiseProtectionisusedinconjunctionwiththeinterleaverdelaysetting, INPenablesenhancednoiseprotectionandisbeingusedmoreforIPvideoapplications. DEPH:ActualInterleavingDepthisanindicationofhowmanyframesareallocatedforinterleaving.Theinterleaverdepthissettomeetthenetworkserviceprovidersrequirements forerrorburstprotectionandlatency.Therangefordepthis14096. PWR:AggregatetransmitPower. FAR END VENDER:ReadsthevendorIDcodeprovidedfromtheCOATU-C,ifMODEM MODEissetforCPE,orthecodefromtheCPEATU-R,iftheMODEMMODEissetforCO. CURRENT STATUS F-keys RETRAIN(F3):Restartthelinkwiththefarenddevice. STORE(F4):Savethereportedresults.SeeSection 2.6. Interpreting the Results Fixed Rate Circuits Fixedratecircuitsspecifiesanexactdatarate forthe customer.IftestingaFixedRate service,lookatthefollowing:12 SSMTT-48 UDSL Module

RATE:Confirmthatthisvalueequalsthefixedratesetforthecircuit,inboththeupstreamand downstreamdirections.Forexample,ifthecircuitundertestisconfiguredforafixedrateof 22016kbpsdownstream/5504kbpsupstream,confirmthatthismeasurementisachieved. SNRM:Confirmthatthesignal-to-noisemargincomplieswithyourcompanysrequirements.A commonstandardis8dB,highervaluescanprovidemoreroomforanyintroducednoise. Rate Adaptive Circuits Rateadaptivecircuitsspecifyminimumandmaximumdataratesforacircuit,andtryto attainthemaximumratesetbytheDSLAM.IftestingaRateAdaptiveservice,lookatthe following: RATE:Thisvalueshouldbebetweentheminimumandmaximumthresholdssetforthe circuit. SNRM:Thesignal-to-noisemarginvaluealsoneedstobeabovetheminimumallowable margin.Commonlyitis8dB,yourmarginmightbehigher.Sincerateadaptivecircuitstry touseallthepossiblebandwidth,thenoisemarginwilltypicallybeverycloseto6dB(or theminimumvalue). 2.2.2 Error Measurements11:50:45 >SHOWTIME CPE MODE:ADSL2+ANNEX A VDSL2 PROFILE:N/A ERROR MEASUREMENTS ST:11:45:25 ET:000:05:20 LOCAL CRC/CV:0 FEC :0 SEF :0 HEC :0 REMOTE CRC/CV:0 FEC :0 HEC :0

11:50:45 >SHOWTIME CPE MODE:ADSL2+ANNEX A VDSL2 PROFILE:N/A ERROR MEASUREMENTS ST:11:45:25 ET:000:05:20 LOCAL ES :0 SES:0 UAS:0 REMOTE ES :0 SES:0 UAS:0

BER :0.00E-0 RETRAINS:0RESTART PAUSE STORE

RESTART

PAUSE

STORE

Figure 8 Error Measurements Screens TheERRORMEASUREMENTSscreen,shownontheleftinFigure8,reportsthefollowing informationforbothLOCALandREMOTE: CRC/CV:CyclicRedundancyCheckanomalyindicatesthatinthedatastream,areceived CRC-8codeisnotidenticaltothelocallycalculatedCRC-8code. FEC:ForwardErrorCorrectionanomalyindicatesthaterrorshavebeencorrectedinthe datastream. SEF:NumberofSeverelyErroredFramesdefectsduringmeasurement(LOCALonly). HEC:HeaderErrorControlerrorindicatesthatanATMcellwithanincorrectHECiscontained in the datastream. Press toviewtherightERRORMEASUREMENTSscreenshowninFigure8.Itreportsthe followinginformationforbothLOCALandREMOTE(exceptBERandRETRAINS): ES:AnErroredSecondisdefinedasonesecondcontainingoneormoreCRC/CVerrors. SES:ASeverelyErroredSecondisdefinedasonesecondcontaining18ormoreCRC/ CVerrors. UAS:AnUnavailableSecondbeginsaftertenconsecutiveseverelyerroredseconds. BER:EstimatedBitErrorRatiocalculationbasedontheDSLForumTR-100standard. RETRAINS:Numberofresynchronizations(retrains)thathaveoccurredsincethestartof the measurement. ERROR MEASUREMENTS F-keys RESTART(F1):Restartthemeasurements,resettingallcounterstozero. PAUSE/CONTINU(F2):Pausethemeasurementsorcontinuethemeasurementswithout resetting any counters STORE(F4):Savethereportedresults.SeeSection 2.6.2 UDSL Module Menus 13

2.2.3 Tone Graphic/Table This menu contains: BITSPERTONE SNRPERTONE 2.2.3.1 Bits Per Tone Thisfeaturemeasuresthebitspertonedistributionusedbythemodemtotransmitattheprovisionedrate.Itdisplaysthenumberofbitsassignedpertoneasagraphicorasatable. Duringmodeminitialization,asignal-to-noisemeasurementforeachtoneismade.Bitdistributionisthenoptimizedtomeetthedesiredbitrate.Eachtonecansupportatheoreticalmaximumof15bits.Duringoperation,thebitdistributionmaybeadjustedtooptimizebandwidth. Themodemconstantlymonitorsthesignal-to-noiseratioforeachtone.Ifatonedegradesin quality,itsendsabitswapcommandtoadjusttheamountofbitsassignedtothatparticular tone.Thesebitsmaybeaddedtoadifferenttoneortakenoutcompletely.11:50:45 >SHOWTIME CPE MODE: N/A ADSL2 PROFILE:N/A TONE 15 65 (280 kHz): 2 BITS SHOWTIME CPE MODE: N/A ADSL2 PROFILE:N/A STORE ZOOM 255 more more

# BITS # BITS # BITS # BITS 0 0 8 0 16 0 24 0 1 0 9 0 17 0 25 0 2 0 10 0 18 0 26 0 3 0 11 0 19 0 27 0 4 0 12 0 20 0 28 0 5 0 13 0 21 0 29 0 6 0 14 0 22 0 30 0 7 0 15 0 23 0 31 0 GRAPHIC STORE

Figure 9 Bits Per Tone Screens IntheleftscreeninFigure9,theleftblockofbitsrepresentstheupstreamsignal.Thehigher frequencygroupattherightrepresentsthedownstreamsignal.Thereisabufferbetween theupstreamanddownstreamfrequencies,whichisrepresentedbythegapbetweenthe upstreamanddownstreamtones. Tolearntheexactbitcountandfrequencyofaspecifictone,seethelinejustabovethegraph. Thislineprovidesthebitcountforthetonemarkedbythepointerarrow.InFigure9,thepointer arrowisatthefirstdownstreamtone,thusthelinereadstone65(280kHz)withtwobits. Tomovethepointerarrow: Press or tomovethepointerarrowonetoneatatime. Press>(F2)tomovethepointerarrowtoanothertickmarkshownonthe horizontalaxisofthegraph. TheGraphiccandisplaytwodifferentscalesusingZOOM(F3): Thefirstscaledisplaysall255tonesinthesamescreen,asintheleftscreeninFigure9. PressZOOM(F3)todisplay0127tonesinonescreen,movethepointerpast127to viewtones128255inonescreen.PressZOOM(F3)toreturntothefirstviewofall 255 tones in the same screen. YoucanalsoviewatableofthetonesbypressingTABLE(more,F4).Anexampleisshown intherightscreeninFigure9.Listedforeachtoneisthenumberofbitsassignedtoit.Press or to scroll through all tones. Ineitherscreen,presstheSTOREF-keytosavetheresults.SeeSection 2.6fordetails. Interpreting the Results Thelowerfrequencytonesrepresentthebandwidthusedfortheupstreamsignal.Thehigher frequencytonesattherightshowthefrequenciesusedforthedownstreamsignal. Thebitsshoulddroptozeroaftertheendoftheupstream.Thisisthebufferbetween theupstreamanddownstreamsignals.Theactualsizeofthisbuffervaries.14 SSMTT-48 UDSL Module

Ifthereisamajordropinbitsineitherthedownstreamortheupstreamsection,this mayindicatethatthereisapossibleinterfereratthatfrequency.Forexample,ifthere isamajordropat772kHz,thismayrepresentaninterferingT1signal. 2.2.3.2 SNR Per Tone Thisfeaturemeasuresthesignal-to-noiseratioforeachdownstreamtoneusedbythemodem totransmittheprovisionedrate.ItdisplaystheSNRpertoneasagraphicorasatable. Duringmodeminitialization,asignal-to-noisemeasurementismadeforeachtone;bitdistributionisthenoptimizedtomeetthedesiredbitrate.Duringoperation,thebitdistribution maybeadjustedtooptimizebandwidth.Themodemconstantlymonitorsthesignal-to-noise ratioforeachtone.Ifatonedegradesinquality,itsendsabitswapcommandtoadjust theamountofbitsassignedtothatparticulartone.Thesebitsmaybeaddedtoadifferent toneortakenoutcompletely.11:50:45 >SHOWTIME CPE MODE: N/A ADSL2 PROFILE:N/A TONE 100 64 (276 kHz): 5.0 dB SHOWTIME CPE MODE: N/A ADSL2 PROFILE:N/A # 0 1 2 3 4 5 6 7 dB 0 0 0 0 0 0 0 0 # 8 9 10 11 12 13 14 15 dB 0 0 0 0 0 0 0 0 # 16 17 18 19 20 21 22 23 dB 0 0 0 0 0 0 0 0 # 24 25 26 27 28 29 30 31 dB 0 0 0 0 0 0 0 0 STORE

ZOOM

moremore

GRAPHIC

STORE

Figure 10 SNR Per Tone Screens In the left screen in Figure 10, the frequency group shown represents the downstream signal. Tolearntheexactsignal-to-noise ratioforaspecifictone,seethelinejustabovethegraph. This line provides the signal-to-noise ratioforthetonemarkedbythepointerarrow.InFigure 10,thepointerarrowisbelowthefirstdownstreamtone,thusthelinereadstone64(276 kHz)witha5dBSNR. Tomovethepointerarrow: Press or tomovethepointerarrowonetoneatatime. Press>(F2)tomovethepointerarrowtoanothertickmarkshownonthe horizontalaxisofthegraph. TheGraphiccandisplaytwodifferentscalesusingZOOM(F3): Thefirstscaledisplaysall255tonesinthesamescreen,asintheleftscreeninFigure 10. PressZOOM(F3)todisplay0127tonesinonescreen,movethepointerpast127to viewtones128255inonescreen.PressZOOM(F3)toreturntothefirstviewofall 255 tones in the same screen. YoucanalsoviewatableofthetonesbypressingTABLE(more,F4).Anexampleisshown intherightscreeninFigure10.Listedforeachtoneisthenumberofbitsassignedtoit. Press or to scroll through all tones. Ineitherscreen,pressSTORE(more,F2)tosavetheresults.SeeSection 2.6fordetails.

2 UDSL Module Menus

15

2.2.4 Event Tracer UsetheEVENTTRACERscreen,showninFigure 11:50:45 11,totrackmodemeventswhenthetestsetiscon>SHOWTIME < CPE MODE: N/A nected to the circuit. ADSL2 PROFILE:N/A IntheEVENTTRACERscreen,use or to seEVENT TRACER lectanevent.AselectedeventdisplaysEVENTID, EVENT ID : 2 of 10 EVENTDATE,TIME,andthetypeofevent,inthis EVENT DATE: 3/10 TIME EVENT case,Showtime.Thescrollbarontherightindicates 16:45:09 Training that more screens are available. 16:45:15 Showtime 16:45:24 CRC Detected InadditiontothemodulesMODE(COorCPE)and 16:45:24 FEC Detected PROFILEselectedintheMODEMSETUPscreen, 16:45:34 CRC Detected 16:46:05 FEC Detected thefollowingarereported: LIMITED CLEAR EVENT ID: The selected event indicates its number outofthetotalevents. Figure 11 Event Tracer Screen EVENT DATE: The date that the selected event occurred. EVENT TRACER F-keys LIMITED/CONTINU(F1):LIMITEDisusedtocaptureupto100events,capturingstopsat thatpoint.UseCONTINUtocontinuouslycaptureeventsinaqueue.Whenthequeueis full,thefirsteventisoverwrittenbythenextevent. CLEAR(F2):Clearallevents.

16


2.3 IP Data Features (Software Option)IPDATAFEATURESareanoption.Ifunavailablethetestsetwilldisplay,OPTIONISNOT ENABLED.Thismenucontains: IPCONFIGURATION IPSTATUS PINGTEST TRACEROUTE WEBACCESSTEST 2.3.1 IP Configuration ThisscreencontainsconfigurationitemsfortheIPconnection.Entertheproperprotocol usedbythecircuit,aswellasthenecessaryIPaddresses. Note:CONNECT/DISCappearsateitherF3orF4dependingonthesettingselected.Press CONNECTtostarttheconnectionproceduretotheISP.PressDISCtoreleasetheconnection.OnceCONNECTispressed,theconnectionwillstayUP,ifsuccessful,orDOWN ifunsuccessful.Thisisindicatedatthetoprightofthescreen.Ineithercase,pressDISC tochangeanyoftheconfigurationitems. Configurethefollowing: INTERFACE Options:DSL-ATM(F1),DSL-PTM(F2),10/100(more,F1),PROFILE(more,F2) Selecttheportconnectionusedfortesting. DSL-ATM:ThisinterfaceusestheUDSLmoduleport.SelectthisfortraditionalATM encapsulatedprotocols;PPPoE,PPPoA,Bridged,andCLIPoA. DSL-PTM:ThisinterfaceusestheUDSLmoduleport.SelectthisfornewerIPbased DSLAMs that support Packet Transfer Mode (PTM). It supports Routed and PPPoE protocols. 10/100:Thisinterfaceusesthe10/100(Ethernet)moduleport. PROFILE:RetrieveandusestoredIPconfiguration.SeeSection 2.7fordetails. MODE Options: ETHERNT or BRIDGED (F1), PPPoE (F2), PPPoA (F3), CLIPoA (more, F1), ROUTED(more,F2) Selecttheprotocolmodeforthetest. ETHERNT:Ethernetisavailableonlywhenthe10/100INTERFACEisselected. BRIDGED:BridgedprotocolaccordingtoRFC2684bridgeencapsulation.Itsupportsboth staticandDHCPIPmanagement.ThismodeisavailablefortheDSL-ATMinterface. PPPoE:PointtoPointProtocoloverEthernetaccordingtoRFC2516.Itsupportsdynamic IPaddressing.ThismodeisavailableforboththeDSL-ATMandDSL-PTMinterfaces. PPPoA:PointtoPointProtocoloverATM(AsynchronousTransferMode),accordingtoRFC 2364.ItsupportsdynamicIPaddressingandisavailablefortheDSL-ATMinterface. CLIPoA:ClassicalIPoverATMaccordingtoRFC2225supportsstaticIPmanagement. ThismodeisavailablefortheDSL-ATMinterface. ROUTEDsupportsstaticandDHCPIPaddressing.ThismodeisavailablefortheDSLPTMinterface. BRIDGEisusedforIPDataPassThroughModefortheDSL-PTMinterface.SeeSection 2.3.6. The remainder of the screen settings are dependent on the selected INTERFACE and MODE,refertothefollowingthreesubsectionsandconfiguretherestofthesettings: Note:Toenternumbersinthesescreens,useSHIFTandthenumerickeypad.Usethe F-keystomovethecursor.Whenfinished,pressSHIFT.

2 UDSL Module Menus

17

2.3.1.1 IP DSL-ATM Configuration11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :BRIDGED ENCAPSULATION:LLC VPI :8 VCI :35 IP TYPE :STATIC LOCAL IP :207.181.199.105 GATEWAY :207.181.199.100 SUBNET MASK :255.255.248.000 DNS SERVER :207.181.199.178 BRIDGED PPPoE PPPoA more 11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :CLIPoA ENCAPSULATION:LLC VPI :8 VCI :35 IP TYPE :STATIC LOCAL IP :207.181.199.105 PEER IP :207.181.199.108 GATEWAY :207.181.199.100 SUBNET MASK :255.255.248.000 DNS SERVER :207.181.199.178 CLIPoA ROUTED CONNECT more < 11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :PPPoA ENCAPSULATION:LLC PAP/CHAP :AUTO VPI :8 VCI :35 IP TYPE :DYNAMIC USER ID :USER5468 PASSWORD :SERVICE2356 DSL-ATM PPPoE PPPoE more 11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :PPPoE ENCAPSULATION:LLC PAP/CHAP :AUTO VPI :8 VCI :35 IP TYPE :DYNAMIC USER ID :USER5468 PASSWORD:SERVICE2356 BRIDGED PPPoE PPPoA SHOWTIME IP UP< verifyIPconfiguration.ISPconnectionstatusisdisST:11:20:40 ET:000:30:05 playedatthetopofthescreen,asshowninFigure IP STATUS 16.ItcanbeIPUP,ifpassed,IP...inprocess,or IPDOWN,iffailed.Statusisalsodisplayedunder STATIC:PASS LOCAL IP :192.168.102.106 IPSTATUS,itcanbe: SUBNET MASK:255.255.255.255 STATIC:InProgress:Theconnectionisnotyet GATEWAY :207.181.199.178 DNS SERVER :206.13.28.41 competed. PASS:Asuccessfulconnection. FAIL:Theconnectionwasnotsuccessful. Thefollowingisreported,ifPASSisdisplayed: LOCAL IP:IPaddressofthetestset. Figure 16 Static IP Status Screen SUBNET MASK:Netmask GATEWAY:IPaddressofthegateway. DNS SERVER:DNSServerIPaddress.

22


2.3.2.3 PPP Dynamic IP Status AfterpressingCONNECT,thetestsetbeginsPPP 11:50:45 negotiationwithanISP.TheISPconnectionstatusis >SHOWTIME PPP UP< displayedatthetopofthescreen,asshowninFigure ST:11:20:40 ET:000:30:05 17.ItcanbeIPUP,ifpassed,IP...inprocess,orit IP STATUS canbeIPDOWN,iffailed.Statusisalsodisplayed PPP:PASS underIPSTATUS,itcanbe: PPP: in progress: The connection is not yet LOCAL IP :192.168.102.106 SUBNET MASK:255.255.255.255 opened. GATEWAY :207.181.199.178 PPP: PASS: Indicates that the authentication DNS SERVER :206.13.28.41 andIPparametersoftheconnectionhavebeen successfullynegotiatedandtheconnectionisup. PPP:FAIL:Indicatesthattheauthenticationor theIPparametersoftheconnectionhaventbeen Figure 17 PPP Dynamic IP Stasuccessfullynegotiatedandthattheconnection tus Screen isdown.Ifthisoccurs,verifytheIPsettingsand try again. Ifsuccessful,thenthefollowingaredisplayed: LOCAL IP:IPaddressoftheATU-R. GATEWAY:IPaddressofthegateway. SUBNET MASK:Netmask. DNS SERVER:DNSServerIPaddress. 2.3.3 Ping Test Beforerunningapingtest,theconnectionmustbe 11:50:45 UPasindicatedatthetoprightofthescreen,as >SHOWTIME IP UP< ST:--:--:-ET:---:--:-showninFigure18. ThePINGscreenisthesameforallIPmodetypes. LOCAL IP:207.181.199.106 PING TEST PressSTART(F4)afterconfigurationtostarttheping DEST. IP :207.181.199.178 PING COUNT :10 test. Press again to stop the test. PING LENGTH:64 Thefollowinginformationisdisplayed: PING: ST:StartTimeindicateswhenSTARTwaspressed. Round Trip (ms) Sent :Min:ET:ElapsedTimesinceSTARTwaspressed. Received :Max:LOCAL IP:DisplaystheLOCALIPenteredintheIP Loss Rate:- % Avg:CONFIGURATIONscreen,ifstaticIPTYPEhasbeen CONTINU START selected.Itdisplaysthedynamicallyassignedaddress, ifDHCP,orDYNAMICIPTYPEhasbeenselectedin Figure 18 PING Test Screen theIPCONFIGURATIONscreen. Ping Test Configuration DEST. IP/DEST. URL Options:URL/IPADDR(F1),LIST(F1)LISTisavailablewhenthecursorhasbeenmoved totherightof:onthisline. EntertheDestinationIP/URLaddress. IPADDR:EnteradestinationaddressusingSHIFTandnumerickeypadalongwith(F3)orpressLIST(F1),andselectasavedIPaddressfromthelist. URL:UniformResourceLocatorisusedtoenteradestinationdomainnameifaDNS serverisavailable.Toenter,pressURL(F1),thenpressEDIT(F2)todisplayacharacter entryscreen,orpressLIST(F1)fortheDESTINATIONIPlistscreen. Saving an IP Address 1. IntheDEST.line,selectIPbypressingURL/IPADDR(F1)tomakeitreadDEST.IP. 2. MovethecursortothenumberpartoftheDEST.IPlineandpressLIST(F1). 3. IntheIPLISTselectionscreen,selectablanklineandpressEDIT(F3). 4. IntheIPentryscreen,useSHIFT,thenumerickeypad,(F3)toenter a numeric address. 5. Whenfinished,pressSTORE(F4)andtheIPaddressappearsintheIPLISTselection screen.2 UDSL Module Menus 23

TouseanIPaddress,selectoneintheIPLISTscreen,andpressSELECT(F4).The selectedIPaddressnowisdisplayedintheDEST.IPlineofthePINGTESTscreen. ToremoveanIPaddressfromtheIPLISTscreen,selectoneandpressDELETE(F2). Saving an URL Address 1. IntheDEST.line,selectURLbypressingURL/IPADDR(F1)tomakeitreadDEST.URL. 2. MovethecursortotheentrypartoftheDEST.URLlineandpressLIST(F1). 3. IntheURLLISTselectionscreen,selectablanklineandpressEDIT(F3). 4. PressEDIT(F3)toviewcharacterentryscreen. 5. PressINPUT(F3)andthecursorhighlightsAandINPUThaschangedtoSTOP. 6. Use , , ,or tomovethecursortothedesiredcharacterandpressENTERtoselect thatcharacter.ThecharacterwillappearintheURLline. 7. Repeatstep6untilfinished,thenpressSTOP(F3)toexitthecharacterentryscreen. Ifamistakeismade,pressSTOP(F3)anduse or to select the incorrect character. Then use: - DELETE(F2)todeletethecharacter. - INSERT(F1)toaddacharactertotheleftoftheselectedcharacter. - OVER(F1)toreplacetheselectedcharacter. 8. Whenfinished,pressSTORE(F4)toreturntoURLLISTselectionscreen. TouseanURLaddress,selectoneintheURLLISTscreen,andpressSELECT(F4).The selectedURLaddressnowisdisplayedintheDEST.URLlineofthePINGTESTscreen. ToremoveanURLaddressfromthelistscreen,selectoneandpressDELETE(F2). PING COUNT Options:110000;defaultis1. Selectthenumberofpingstosend.UseSHIFTandthenumerickeypadtoenteravalue, orpressCONTINU(F1)forcontinuous. PING LENGTH Options:641500bytes;defaultis64. Selectthepinglengthtosend.UseSHIFTandthenumberkeypadtoenteravalue. Whenready,pressSTART(F4).Pressagaintostop.Thefollowingarereported: PING: This line can indicate: PING::Thetesthasntbeenstarted. PING:InProgress:Thetestisinprocess. PING:PASS:Atleastoneechoresponsehasbeenreceived. PING:FAIL:Anechoresponsehasnotbeenreceived. PING:NODNSSERVER:TheDNSserverisunavailable. PING:DNSLOOKUPFAILED:TheIPaddresscouldnotbeassociatedwiththehost name. Thebottomofthescreenreportsthestatisticsofthetest: Sent:Numberofpingssenttothenetwork. Received:Numberofcorrectechoresponsesreceived. Loss Rate:Percentageofreceivedpings(PingsSent/PingsReceived). Round Trip:Measureoftheroundtripdelayinmilliseconds.Min/Max(Minimum/Maximum) andAvg(Average)isreported.

24


2.3.4 Trace Route Beforerunningthetraceroutetest,theconnection must be UP as indicated at the top right of the screen,asshowninFigure19. Use this screen to send ping messages to a destination address and trace the messages across the routersthroughwhichtheytravel.Theresultscreen isthesameforallIPmodetypes. AfterenteringaDESTURLorDESTIP(seeSection 2.3.3forentrydetails),select;11:50:45 >SHOWTIME

IP UPSHOWTIME

IP UP< IP ADDR./URL Options:URL/IPADDR(F2),LIST(F3) WEB ACCESS TEST Enter the URL or IP address of the web page to PROTOCOL:HTTP-DOWNLOAD URL :www.sunrisetelecom.com download.SeeSection 2.3.3forentrydetails. Whenready,pressSTART(F4),pressagaintostop. AsthetestprogressesthePAGEDOWNLOADline STATUS:PASS will blink an in progress message. If the page is SIZE: 9490 bytes successfullydownloadedthislinewilldisplayPASS, TIME: 0.810 seconds ifnotitwilldisplayFAIL.ForaPASSthefollowing RATE: 11.399 Kbytes/sec FTP START informationisdisplayed,asinFigure20: STATUS:Seethepreviousparagraphstartingwith Figure 20 HTTP Download Asthetestprogresses. Web Access Screen SIZE:TotalsizeofthefileinBytes. TIME:Transfertimeinseconds. RATE:TransferrateinKbytespersecond.

2.3.5.2 FTP Download Test Configurethefollowing: IP ADDR./URL Options:URL/IPADDR(F2),LIST(F3) EntertheURLorIPaddressoftheFTPserver.See Section 2.3.3forentrydetails. USERNAME Enter the USERNAME of the account on the FTP server.Thedefaultisblank.Tochangeit,pressEDIT (F1)andusetheprocedureinSection 2.3.1.4.

11:50:45 >SHOWTIME

IP UPSHOWTIME

DHCP UPSHOWTIME < 3. PressCONNECT(F4). IP CONFIGURATION 4. WaitfortheBRIDGEconnectiontobeestablished, INTERFACE :DSL-PTM :BRIDGE whichisindicatedbyaBRIDGE:PASSunderIP MODE STATUSandtheBRGUPstatusindicationat the top right corner. 5. ConnectaPCtotheSSMTT-48s10/100Ethernet IP TYPE :NONE DATAport. Note:ThePCsTCP/IPPropertiesshouldbeconfiguredasfollows: BRIDGED ROUTED PPPoE CONNECT ObtainanIPAddressautomatically. ObtainDNSserveraddressautomatically. Figure 24 IP Configuration 6. UsethePCsNetworkClientSoftware(i.e.MS Bridged Screen WindowsXPNetworkConnectionsPPPoEClient) toestablishtheWANnetworkconnection. 7. Launchawebbrowserandproceedwithinternetaccess.

28


2.4 IP Video Features (Software Option)IPVIDEOfeaturesareanoption.Ifunavailablethetestsetwilldisplay,OPTIONISNOT ENABLED.Thismenucontains: IPCONFIGURATION IPSTATUS VIDEOSTREAMTESTS VODTEST USERCONFIGUREDTEST 2.4.1 IP Configuration ThefirststepforIPVideotestingistoestablishtheIPlayer.TheIPConfigurationscreens presented,mainlydependonthesettingsmadeforINTERFACEandMODEinthefirstIP CONFIGURATIONscreen. INTERFACE Options:DSL-ATM(F1),DSL-PTM(F2),10/100(F3) Selecttheportconnectionusedfortesting. DSL-ATM:ThisinterfaceusestheUDSLmoduleport.SelectthisfortraditionalATM encapsulatedprotocols;PPPoE,PPPoA,andBridged. DSL-PTM:ThisinterfaceusestheUDSLmoduleport.SelectthisfornewerIPbased DSLAMs that support Packet Transfer Mode (PTM). It supports Routed and PPPoE protocols. 10/100:Thisinterfaceusesthe10/100(Ethernet)moduleport. MODE DSL-ATMOptions:BRIDGED(F1),PPPoE(more,F1),PPPoA(more,F2) DSL-PTMOptions:ROUTED(F2),PPPoE(F3) 10/100Options:AUTO(F1) BRIDGED:BridgedprotocolaccordingtoRFC2684bridgeencapsulation.Itsupportsboth staticandDHCPIPmanagement.ThismodeisavailablefortheDSL-ATMinterface. ROUTEDsupportsstaticandDHCPIPaddressing.ThismodeisavailablefortheDSLPTMinterface. PPPoE:PointtoPointProtocoloverEthernetaccordingtoRFC2516.Itsupportsdynamic IPaddressing.ThismodeisavailableforboththeDSL-ATMandDSL-PTMinterfaces. PPPoA:PointtoPointProtocoloverATM(AsynchronousTransferMode),accordingtoRFC 2364.ItsupportsdynamicIPaddressingandisavailablefortheDSL-ATMinterface. AUTO:Thisisonlyavailableif10/100(Ethernet)isselectedforINTERFACE.Themode parameterisautomaticallysettoAUTO(AutoSense). VLAN (INTERFACE=DSL-PTMor10/100) Options:DISABLE(F1),ENABLE(F2) Choosetouse,ornotuseVLANtags.Ifenabled,enteravalueforPandVID. P IfVLANisenabled,enteraVLANPrioritynumber,08. VID IfVLANisenabled,enteraVLANIdentificationnumber,04095. ENCAPSULATION(INTERFACE=DSL-ATM) Options:LLCSNAP(F1),VCMUX(F2) ChoosetheencapsulationmethodforcarryingtrafficoverAALType5overATM. LLCSNAP:LogicalLinkControlbasedonIEEEstandard802.2.LLCencapsulationis usedwhenmultipleprotocolareencapsulatedoverasingleATMVirtualConnection. VCMUX(BRIDGEonly):UsedwhenoneprotocoliscarriedoverasingleATMVirtual Connection. PRIMARY VPI (INTERFACE=DSL-ATM) Options:0255 EnterthePrimaryVPIviaSHIFTandthenumerickeypad.2 UDSL Module Menus 29

PRIMARY VCI(INTERFACE=DSL-ATM) Options:065535 EnterthePrimaryVCIviaSHIFTandthenumerickeypad. IP TYPE Options:DHCPorDYNAMIC(F1),STATIC(F2) DHCPorDYNAMIC:DynamicHostConfigurationProtocolprovidesawayfordevicesto obtainprotocolconfigurationparameters(localIPaddress)dynamicallyfromthenetwork. ThetestsetsendsaDHCPrequesttoaDHCPserver;theDHCPserverrespondsand providesanIPaddress.ThetermDYNAMICisusedinPPPandDHCPisusedinall otherIPtypes. STATIC:EnteranIPaddress,SubnetMaskandGatewayIPaddressforthetestset. 2.4.1.1 IP Type Static Configuration11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :BRIDGED ENCAPSULATION:LLCSNAP PRIMARY VPI :15 PRIMARY VCI :35 # OF STREAMS :4 IP TYPE :STATIC MAC TYPE MAC ADDRESS :MTT :00:E0:A6:75:75:76 10/100 CONNECT CONNECT < 11:50:45 >SHOWTIME IP CONFIGURATION LOCAL IP :207.181.199.105 SUBNET MASK:255.255.248.000 GATEWAY :207.181.199.100 SHOWTIME IP CONFIGURATION TEST TEMPLATE:TMPE1 IGMP VERSION :V2 STREAM #1 STREAM #3 VPI:15 VPI:15 VCI:35 VCI:35 EPG:TABLE1 EPG:TABLE2 STREAM #2 VPI:15 VCI:35 EPG:TABLE1 SELECT NONE STREAM #4 VPI:15 VCI:35 EPG:TABLE2 VOD

SHOWTIME VOD CONFIGURATION PRIMARY VPI :15 PRIMARY VCI :35 URL LIST :URL1 VOD SERVER :207.181.199.178 PORT NUMBER :554 VIDEO PATH : /movie/twister USER NAME :USER5468 USER PIN :SERVICE2356 DIGEST SCHEME:MD5

SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :BRIDGED ENCAPSULATION:VC MUX PRIMARY VPI :15 PRIMARY VCI :35 # OF STREAMS :4 IP TYPE :DHCP OPTION 61 :ENABLE MAC TYPE :MTT MAC ADDRESS :00:E0:A6:75:75:76 DSL-ATM DSL-PTM 10/100 CONNECT SHOWTIME IP CONFIGURATION DHCP OPT 60:ENABLE example.com DHCP OPT 77: ENABLE DHCP OPT 43: ENABLE SHOWTIME IP CONFIGURATION TEST TEMPLATE:TMPE1 IGMP VERSION :V2 STREAM #1 STREAM #3 VPI:15 VPI:15 VCI:35 VCI:35 EPG:TABLE1 EPG:TABLE2


SHOWTIME IP CONFIGURATION INTERFACE :DSL-ATM MODE :PPPoE ENCAPSULATION:LLCSNAP PRIMARY VPI :15 PRIMARY VCI :35 # OF STREAMS :4 IP TYPE :DYNAMIC PAP/CHAP :CHAP USER ID :USER5468 PASSWORD :SERVICE2356 DSL-ATM DSL-PTM

SHOWTIME IP CONFIGURATION TEST TEMPLATE:TMPE1 IGMP VERSION :V2 STREAM #1 STREAM #3 VPI:15 VPI:15 VCI:35 VCI:35 EPG:TABLE1 EPG:TABLE2


WAITING CONFIGURATIONscreen. VOD URL LIST Note:TheMMCcardmustcontaintheVODURLList NO URL 1 192.168.165.100:554/twister file(URList.csv)inthePROFILEfolderforproperde2 192.168.165.100:554/rainman tection.Otherwise,amessageisdisplayedindicating 3 192.168.165.100:554/spide..2 4 192.168.165.100:554/spide..1 theURLlistisnotavailable. 5 192.168.165.100:554/strips 6 192.168.165.100:554/jarhead DisplayedforeachURL: 7 192.168.165.100:554/bat..ins NO:A199sequencenumberstoredonthetest 8 192.168.165.100:554/supe..II 9 192.168.165.100:554/adve..la set MMC card. 10 192.168.165.100:554/boys..nd URL:AURLwithportnumberandVODobjectaccess SELECT PAGE-UP PAGE-DN path,storedonthetestsetMMCcard;forexample: 192.168.165.100:554/vod_server/videofile.mpg Figure 28 VOD URL List Screen Use , ,PAGE-UP(F2),orPAGE-DN(F3)toselectaURL.PressSELECT(F1)todisplaytheVODCONFIGURATIONscreen,withthe requiredinformationfilledinfromyourselectionforVODSERVER,PORTNUMBER,and VIDEOPATH. Creating a URL List file 1. IfyourMMCcarddoesnotalreadycontainaURList.csvfileinitsPROFILEfolder,use MicrosoftExceltocreateanewfile. 2. Inthefirstcolumntoprowoftheworksheet,enterNO,andinthesecondcolumntop rowenterURL 3. IntheNOcolumn,secondrow,enterasequentialnumberofURL,startingwith1.This numberisonlyforinformativeuse. 4. IntheURLcolumn,secondrow,enterthevideoserveraddress;VODportnumber;and filepathwiththefullnameofthevideofileincludingthevideofiletype;e.g. 192.168.165.100.1:554/vod_server/videofile.mpg Note: : and / are separators that need to be followed as indicated in the example. 5. Ifnecessary,continuefillinginrowsbyrepeatingsteps3and4untilfinished. 6. Savethefile,usingthisfilename:URList.csv Note:InExcelsSaveAsdialogwindowatFormat,selectCSV(Commadelimited) forthefiletype. 7. MountthetestsetsMMCcardontoyourPC. 8. CopythefileintothePROFILEfolderoftheMMCcard. 9. UnmounttheMMCcardfromyourPC,usingtheunmountcommandpeculiartoyour PCsoperatingsystem. 10.InserttheMMCcardintothetestset. 11.Powerupthetestset. 12. NavigatetotheVODURLLISTscreentoselectyourentriessavedintheURList.csvfile.

36


2.4.1.6 Test Template Creation ThetesttemplateisstoredonthetestsetsMMCcardwithinthePROFILEfolder.Thefile iscreatedusingMicrosoftExcel.UseTable5asaguide.Onceatemplateiscreated, saveitasaTMPExx.csv(commadelimited)fileandcopyittothePROFILEfolderonthe MMCcard.Notethatxxreferstoanumberofyourchoosingfrom199. Excel Column Field Name Format A TestNumber Number;199 B C D E F G H I J K L TestEntry Alphanumeric;125characters;informativeonly(name Name ofatest). IPGMAX 8characterkeywordusedtodenotethetestparameter IPGMAX. IPGMAX 1999;endedwiths,ms,orustodenotesecond, Threshold minisecond or nanosecond. IPGMIN 8characterkeywordusedtodenotethetestparameter IPGMIN. IPGMIN 1999;endedwiths,ms,orustodenotesecond, Threshold minisecond or nanosecond. JITRMAX 8characterkeywordusedtodenotethetestparameter JITTERMAX. JITRMAX 1999;endedwiths,ms,orustodenotesecond, Threshold minisecond or nanosecond. LATCMAX 8characterkeywordusedtodenotethetestparameter LATENCYMAX. LATCMAX 1999;endedwiths,ms,orustodenotesecond, Threshold minisecond or nanosecond. PACKLOS 8characterkeywordusedtodenotethetestparameter PACKETLOSS. PACKLOS 1100;endedwith%todenotethepercentageofloss Threshold packetscomparingtoreceivedpackets. 1999;no%symbolattheenddenotethenumberis anactuallosspacketcount. STRM 4characterkeywordthatmustexiststodenoteavalid entry. Stream A14digitnumberincombinationof1,2,3,and4, Number e.g.1,2,23,1234.Denotesvideostreams1,2,3,4in testing. TIME 4characterkeywordthatmustexiststodenoteavalid entry. Test Time Anumberintherangeof1180;denotestesttimefrom 1180minutes.

M N

O P

Notes: Avalidtestscriptentryinthetemplateshallconsistofatleastonetestparameter keyword(i.e.,IPGMIN,JITRMAX,PACKLOSetc). Thecorrespondingcolumnsshallbeleftblankifatestparameterisnotincludedina testscript.Refertothetemplateexampleforsuchcases. Alltestscriptentriesinatemplate(intheselectedCSVfile)shallbesyntaxchecked beforeanentryislistedinthePRE-CONFIGUREDTESTSscreen.Atestentrythat failedinsyntaxvalidationshallnotbedisplayedinthemenu. Table 5 Test Template Creation Guide

2 UDSL Module Menus

37

2.4.1.7 EPG Channel Table Creation TheEPGChanneltableisstoredonthetestsetsMMCcardwithinthePROFILEfolder. ThefileiscreatedusingMicrosoftExcel.UseTable6asaguide.Onceatableiscreated, saveitasaEPGxx.csv(commadelimited)fileandcopyittothePROFILEfolder.Note thatxxreferstoanumberofyourchoosingfrom199. Excel Column A B C Field Name Format Numericinthefollowingformat: 239.255.0.11:1234 Alphanumeric;maximumofthreecharacters ChannelNumber Number;199 Address Code

Table 6 EPG Channel Table Creation Guide

38


2.4.2 IP Status DHCP Status After pressing CONNECT in the configuration 11:50:45 screen,thetestsetsendsaDHCPdiscoverymes>SHOWTIME DHCP UP< ET:000:30:05 sagetostarttheDHCPnegotiationwiththeDHCP ST:11:20:40 IP STATUS serverandobtainanIPaddress. DHCP: PASS IntheIPSTATUSscreen,theStartTime(ST)and LOCAL IP :192.168.102.106 theElapsedTime(ET)canbeviewed. GATEWAY :207.181.199.178 Thestatusisdisplayedatthetoprightsideofthe SUBNET MASK:255.255.255.255 IPSTATUSscreenontheleftinFigure29.Itcan be DHCP..., if in process. DHCP UP, if DHCP haspassed.OritcanbeDHCPDOWN,ifDHCP hasfailed.ThestatusisalsodisplayedundertheIP STATUSlineinthesamescreen.Itcanbe: DHCP: IN PROG: The connection is not yet Figure 29 DHCP IPTV Status completed. Screen DHCP:PASS:Indicatesasuccessfulconnection. DHCP:FAIL:Indicatesthattheconnectionwasnotsuccessful. Thefollowingisreported,ifDHCP:PASSisdisplayed: LOCAL IP:IPaddressofthetestsetassignedbytheDHCPserverorifSTATICthisreports the address entered in the configuration screen. GATEWAY:IPaddressofthegateway. SUBNET MASK:Netmask. Static Status After pressing CONNECT in the configuration 11:50:45 screen,thetestsetsendsanARP(AddressResolu>SHOWTIME IP UP< tionProtocol)requesttothegateway. ST:11:20:40 ET:000:30:05 IP STATUS IntheIPSTATUSscreen,theStartTime(ST)and ARP: PASS theElapsedTime(ET)canbeviewed. LOCAL IP :192.168.102.106 Thestatusisdisplayedatthetoprightsideofthe GATEWAY :207.181.199.178 IPSTATUSscreenontheleftinFigure30.Itcanbe IP...,ifinprocess.IPUP,ifithaspassed,orIP DOWN,ifithasfailed.Thestatusisalsodisplayed under the IP STATUS line in the same screen. It can be: ARP:INPROG:Theconnectionisnotyetcompleted. Figure 30 Static IPTV Status ARP:PASS:Asuccessfulconnection,thegate- Screen wayhasrepliedtotheARPrequest,andIPUP is displayed. ARP:FAIL:Connectionwasnotsuccessful,thegatewayhasnotrespondedtotheARP requestandIPDOWNisdisplayed. Thefollowingisreported,ifARP:PASSisdisplayed: LOCAL IP: IP address entered in the LOCAL IP field before the CONNECT F-key was pressed. GATEWAY:IPaddressofthegateway.

2 UDSL Module Menus

39

2.4.3 Video Stream Tests This menu contains: STREAMCONFIGURATION TSRATES TSMEASUREMENTS PIDANALYSIS CHANNELTEST MDITEST TS RATES, TS MEASUREMENTS, PID ANALYSIS, and MDI TEST F-keys RESTART(F1):RestartthemeasurementresettingETtozero. PAUSE/CONTINU(F2):Pausethemeasurementorcontinuethemeasurementwithout resettingET. STORE: Save your measurement. See Section 2.6fordetails. 2.4.3.1 Stream Configuration Usethisscreentochooseifastreamwillbetested.Therecanbeuptotwoscreensavailabledependingon#OFSTREAMSselectedinIPCONFIGURATIONinSection 2.4.1.11:50:45 >SHOWTIME DHCP UP< STREAM CONFIGURATION STREAM #1 :ON ENCAPSULATION:MPEG-TS SOURCE :MANUAL IGMP ADDRESS :239.255.012:102 PORT NUMBER :0 STREAM #2 :OFF ENCAPSULATION:MPEG-TS SOURCE :TABLE CHANNEL :012 MANUAL TABLE 11:50:45 >SHOWTIME DHCP UP< STREAM CONFIGURATION STREAM #3 :ON ENCAPSULATION:MPEG-TS SOURCE :TABLE CHANNEL :012 STREAM #4 :OFF ENCAPSULATION:MPEG-TS SOURCE :MANUAL IGMP ADDRESS :239.255.012:102 PORT NUMBER :1 MANUAL TABLE

Figure 31 Stream Configuration Screens STREAM #1, #2, #3, and #4 ChoosewhetherornottotestavideostreambypressingON(F1)orOFF(F2).Notethat thissettingmustbeONtoconfiguretherestofthisscreen. ENCAPSULATION Options:MPEG-TS(F1) MPEG-TSistheonlyoption.MPEG-TSisoneormultiple188-byteMotionPicturesExperts Group-TransportStreampacketsencapsulatedinUDP(UserDatagramProtocol)orRTP (Real-timeTransportProtocol)packets. SOURCE Options:MANUAL(F1),TABLE(F2) MANUAL:Ifselected,enteranADDRESSviaSHIFTandthenumerickeypad. TABLE:Ifselected,CHANNELreplacesIGMPADDRESSandPORTNUMBER,this allowsselectionofachannelselectedfromtheEPGTABLE. IGMP ADDRESS(SOURCE=MANUAL) EntertheInternetGroupManagementProtocolAddressnumberofavideostreamusing SHIFTandthenumerickeypad. PORT NUMBER(SOURCE=MANUAL) EnterthePortNumberofavideostreamusingSHIFTandthenumerickeypad. CHANNEL(SOURCE=TABLE) Ifadifferentchannelisneeded,pressSELECT(F1)andtheEPGTABLEscreenisdisplayed. Chooseanewchannelusing or ,thenpressSELECT(F1)toreturntotheSTREAM CONFIGURATIONscreenwiththenewchanneldisplayed.TocreatedatafortheEPGTABLE screen,seeSection 2.4.1.7. Whenfinished,pressESC.40 SSMTT-48 UDSL Module

2.4.3.2 TS Rates UptofourTransportStreamscreenscanbeavail11:50:45 able,dependingon#OFSTREAMSselectedinIP >SHOWTIME DHCP UP< CONFIGURATIONinSection 2.4.1. ST:11:48:40 ET:000:02:05 TheTSRATESscreenreportsthefollowingforeach TS RATES - STREAM #1 CHANNEL : 239.255.012:102 STREAM: STATUS : STREAMING ST: Start Time. TOTAL RATE : 2089.42 kbps VIDEO ET:ElapsedTime. CURRENT : 1871.36 kbps CHANNEL: The IGMP address selected in the MAX : 1871.36 kbps AUDIO STREAMCONFIGURATIONscreen. CURRENT : 183.29 kbps STATUS: This reports the current condition of the MAX : 192.32 kbps stream.Itcanbe: RESTART PAUSE STORE STREAMING: The selected stream is detected Figure 32 TS Rates Screen and is being measured. OFF:Thestreamisnotselectedformeasurement. FAILED:Theselectedstreamcannotbedetected. TOTAL RATE:Thisisthetotaltransportstreamrateinkbps. VIDEO:TheCURRENTandMAXratesarereported. AUDIO:TheCURRENTandMAXratesarereported. 2.4.3.3 TS Measurements Up to four Transport Stream screens can be avail11:50:45 DHCP UP< able,dependingon#OFSTREAMSselectedinIP >SHOWTIME CONFIGURATIONinSection 2.4.1. ST:11:48:40 ET:000:02:05 VIDEO STREAM #1 InadditiontoSTandET,thisscreenreportsthefolPACKETS lowingforeachSTREAM: RECEIVED : 75888881 EXPECTED : 75889000 PACKETS RECEIVED reports the total received LOST : 119 packets.EXPECTEDreportstheexpectednumber LOSS RATE : 1.566E-06 ofpacketsusingMPEGTS.LOSTisthenumberof IGMP LATENCY: 1.0 uS PACKET JITTER INTER PCKT GAP packets lost. LOSS RATE is derived from LOST/ CUR: 001.0 uS MIN: 002.0 uS MAX: 001.4 uS MAX: 005.0 uS EXPECTEDpackets. AVG: 001.1 uS AVG: 003.4 uS IGMP LATENCY:ThisistheonewaydelayofnetSTORE RESTART PAUSE worktrafficbetweenthetestsetandavideostream Figure 33 TS Measurements controllersuchasaDSLAM. PACKET JITTER:CUR(current)PacketJitterrate, Screen withtheMAX(maximum)andAVE(average)rates, measuringthevariationsofMPEG-TSpacketarrival time. INTER PCKT GAP:Inter-PacketGapreportsMinimum,maximum,andaveragetimegap inbetweenMPEGTSpackets. 2.4.3.4 PID MAP Analysis UptofourTransportStreamscreenscanbeavailable,dependingon#OFSTREAMSselectedinIP CONFIGURATIONinSection 2.4.1. InadditiontoSTandET,thisscreenreportsthefollowingforeachSTREAM: CHANNEL: The IGMP address selected in the STREAMCONFIGURATIONscreen. PID:PacketID. TYPE: Program type of the reported PID, such as video or audio in a video stream. DESCRIPTION: Information available in the video streamthatisassociatedtothePID.11:50:45 >SHOWTIME DHCP UPSHOWTIME DHCP UPSHOWTIME DHCP UP< SelectMANUAL,andinthefileselectionscreen, CHANNEL TEST selectaEPGtable.PressOK(F4)andthetest MODE: MANUAL starts. The test set then reports the previous (PREV)channel,currentchannel,changechannel PREV CHANNEL :N/A CHANNEL:1 (CH) delay, the channels status, STREAMING, CURRENTCH DELAY:300ms CHANGE OK,orFAIL,anditsbandwidthinkbps. STATUS :OK BANDWIDTH :5000kbps TomakeanEPGtableavailableforuse,seeSection 2.4.1.7. Afterthetestiscompleted,pressSTORE(more,F2) AUTO MANUAL START more to save the test results. Figure 35 Channel Test Screens 2.4.3.6 MDI Measurements MDI(MediaDeliveryIndex)measurementsperRFC 11:50:45 4445areanotherwaytocharacterizeandquantify >SHOWTIME DHCP UP< MDI MEASUREMENTS twoIPtransportimpairments:packetjitterandpacket ST:11:48:40 ET:000:02:05 loss. VIDEO STREAM #1 DELAY FACTOR (mS) UptofourTransportStreamscreenscanbeavailCURRENT: 1.0 able,dependingon#OFSTREAMSselectedinIP MAXIMUM: 1.2 MINIMUM: 0.6 CONFIGURATIONinSection 2.4.1. AVERAGE: 0.8 In addition to ST and ET, the screen in Figure 36 MEDIA LOSS RATE (p/sec) CURRENT: 0.0 reportsthefollowingforeachSTREAM: MAXIMUM: 0.0 MINIMUM: 0.0 DELAY FACTOR:Measuredinms,TheCURRENT, AVERAGE: 0.0 MAXIMUM,MINIMUM,andAVERAGE. STORE RESTART PAUSE MEDIA LOSS RATE:Measuredinp/sec.TheCURFigure 36 MDI Measurements RENT,MAXIMUM,MINIMUM,andAVERAGE. Screen

42


2.4.4 VOD Test AfterestablishinganIPconnection,VODtestingcanbeperformed.Thismenucontains: DESCRIBEMEDIA PLAYMEDIA 2.4.4.1 Describe Media TheDESCRIBEMEDIAscreenreportsbasicinfor>SHOWTIME DHCP UP< mationandthestatusofaselectedmediafile. DESCRIBE MEDIA PressSTART(F1)andthetestsetthencomposes VOD SERVER: 192.168.121.100 a RTSP DESCRIBE command with the URL and MEDIA FILE: /MOVIEDIR/SPIDERMAN2 sendsittotheVODserverthroughtheactivetesting TITLE : SPIDERMAN2 interface(eitherDSLorEthernet). AUTHOR : Sam Raimi WhentheVODserverreplies,thetestsetdisplays DURATION: 2:19:42 VIDEO : thefollowinginformation(ifavailable): AUDIO : TITLEofthevideofile. STATUS : TEST PASSED AUTHORofthevideofile. START STORE DURATION:PlayingtimeofthevideofileinHours: Figure 37 Describe Media Screen Minutes: Seconds. VIDEO attribute. AUDIO attribute. STATUS:TESTPASSorTESTFAILisbasedonTable7andinformationisderivedfrom Table 8. DESCRIBE MEDIA F-keys START(F1):SendaRTSPDESCRIBEcommandbyhavingthetestsetcomposeaRTSP DESCRIBEcommandwiththeURLandsendsittotheVODserverthroughtheactivetestinginterface(eitherDSLorEthernet). STORE(F2):SavetheresultsoftheDESCRIBEMEDIAscreen.Thisfunctionsafterthe serverrespondstothetestsetRTSPdescribecommand.SeeSection 2.6fordetails. Status Codes RequestDescribe TestFailed Conditions to Issue Status Code HassentaDESCRIBErequesttotheVODserver. Hasreceivedareplyotherthanthe200OKcode.Thescreenthen displaysthereturncodewhenatestisfailed,e.g.TESTFAILED (404). Hasreceiveda200OKcodefromtheVODserver. Table 7 VOD Status Codes 2.4.4.2 Play Media UsethePLAYMEDIAscreentoanalyzejitter,the numberof droppedpackets, and the status of the selected media file.11:50:45 >SHOWTIME PLAY MEDIA 11:50:45

Test Passed

DHCP UPSHOWTIME IP CONFIGURATION INTERFACE : DSL-ATM MODE : BRIDGED ENCAPSULATION: LLCSNAP VPI VCI IP TYPE LOCAL IP GATEWAY SUBNET MASK DNS SERVER : : : : : : : 17 35 STATIC 67.121.165.242 67.121.164.1 255.255.255.0 203.13.28.12 10/100 CONNECT < 11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE : DSL-PTM MODE : ROUTED VLAN : ENABLE P:7 VID:2095 IP TYPE LOCAL IP GATEWAY SUBNET MASK DNS SERVER : : : : : STATIC 67.121.165.242 67.121.164.1 255.255.255.0 203.13.28.12 < 11:50:45 >SHOWTIME IP CONFIGURATION INTERFACE : 10/100 MODE : ETHERNET VLAN : ENABLE P:7 VID:2095 IP TYPE : DHCP SHOWTIME

DHCP UPSHOWTIME DHCP UP< Ifused,agatekeepercontrolsthecallrouting. PREFERRED CODEC LIST IPADDR:EnteranIPaddress. 1:G.711u NONE:Nogatekeeperisused. 2:G.711A PREFERRED CODEC Thissettingtriesalistofcodecs,thefirstisdisplayed. InFigure42,G.711uisthefirstone. TochangetheorderofthelistpressSELECT(F1).The screenshowninFigure40isdisplayed.Inthisscreen, selectacodectomoveupordownthelist.PressMOVE3:G.792A 4:G.723.1-5.3k 5:G.723.1-6.3k 6:G.726-16k 7:G.726-24k 8:G.726-32k 9:G.726-40k 10:G.729ab MOVE UP MOVE DN RESET

Figure 40 Preferred Codec List2 UDSL Module Menus 45

UP(F1)tomovetheselectedcodecuponeposition,pressMOVEDN(F2)tomovetheselected codecdownoneposition.PressRESET(F4)toresettheordertothedefaultshowninFigure 40.Whenfinished,pressESCtoreturntothePROTOCOLSETUPscreenshowninFigure42. CONNECT Options:NORMAL(F1),FAST(F2) Selectthetypeofconnection. NORMAL:StandardH.323callsetupprocedure. FAST:Fastconnectcallsetupprocedure.Notethatifeitheroneofthetwoendpointsdoes notsupportfastconnect,thenormalconnectprocedurewillbeusedtosetupacall. RTP PORT TheRTPPortnumbercanbeanyevennumberintherangeof102465534;thedefault number is 50000. MY NUMBER/ALIAS Enteranumberforthetestset. AUDIO FILE DELAY (SEC) Options:0(F1),1(F2),3(F3),5(F5) Thetestsetwilltransmitaudiofiles/packetsassoonasacallisestablished.Thefileswill besentcontinuously,withadelayinbetweenfiles,andwillterminatewhenthecallends. Thedelaycanbeconfiguredas0,1,3,or5seconds. SIP Setup PROXY TYPE Options: NONE (F1), DHCP (F2), IP ADDR (F3), NAME(F4) Selectamethodtodeterminetheproxyserverinformation. NONE:Noproxyisused. DHCP:Theproxyservernameand/orIPaddress isdeterminedbytheDHCPprocess. IPADDR:ManuallyenteranIPAddress. NAME:Ifselected,movethecursortothenext lineandpressEDIT(F1)todisplayacharacter entryscreen.UsetheproceduredescribedinMY NUMBER/ALIAStoenteraPROXYNAME.

11:50:45 >SHOWTIME DHCP UP< PROTOCOL SETUPPROTOCOL : SIP PROXY TYPE : IP ADDR 192.168.102.31 REGISTRAR TYPE : NAME sunrise.de AUTHENTICATION : ENABLE USERNAME: mtttest PASSWORD: 54321 REALM : NONE USER NAME: NONE

H.323

SIP

REGISTRAR TYPE 11:50:45 DHCP UP< Options: NONE (F1), DHCP (F2), IP ADDR (F3), >SHOWTIME PROTOCOL SETUP NAME(F4) PERFERRED CODEC: G.711u Select a method to determine the registrar server SIP PORT : 5060 PROXIY PORT : 5060 information. REGISTRAR PORT : 5060 NONE:Noregistrarserverisused. RTP PORT : 50000 MY NUMBER/ALIAS: NAME DHCP:Theregistrarservernameand/orIPadSIPUser23 dressisdeterminedbytheDHCPprocess. MY HOST: IP ADDR 192.168.101.1 IPADDR:ManuallyenteranIPAddress. AUDIO FILE DELAY (SEC):0 NAME:Ifselected,movethecursortothenext line and pressEDIT (F1) to displaya character SELECT entryscreen.UsetheproceduredescribedinMY NUMBER/ALIAStoenteraREGISTRARNAME. Figure 41 SIP Protocol Setup Screens AUTHENTICATION Options:ENABLE(F1),DISABLE(F2) Specifywhetheruserauthenticationisrequiredforregistrationtotheproxyserver.Ifenabled,enteraUSERNAMEandaPASSWORD,bypressingEDIT(F1).Usetheprocedure inMYNUMBER/ALIAS. REALM Enterthealphanumericdescription,ifapplicable.46 SSMTT-48 UDSL Module

USER NAME Enterthealphanumericdescription,ifapplicable. Press toconfigurethebottomscreenshowninFigure41. PREFERRED CODEC See this item in Section 2.5.3. SIP PORT (5060default) EnteraTCP/UDPportnumber.Thedefaultsettingisrecommended. PROXY PORT(5060default) Entertheproxyportvalue. REGISTRAR PORT(5060default) Entertheregistrarportvalue. RTP PORT (50000default) TheRTPPortnumbercanbeanyevennumberintherangeof102465534. MY NUMBER/ALIAS Enterthenumberoralphanumericnameassignedtotheclient/testset.Thisisthealias oftheclient/testsetidentifier(IPaddressandPortnumber)thatisregisteredintheproxy/ registrar servers. To create an entry: 1. WiththecursorbelowMYNUMBER/ALIAS,pressEDIT(F1). 2. Inthecharacterentryscreen,pressINPUT(F3)andtheletterAwillbehighlighted. Press , , ,or tochooseacharacterandpressENTER.Thechosencharacterwill appeartotherightoftheuppercursorentryarea.Repeatuntildone. Ifamistakeismadeintheentry: A. PressSTOP(F3)tomoveoutofthecharactergridandbacktotheentry. B. Move the cursor to the incorrect character. C. PressDELETE(F2)todeletethecharacteror,pressINSERT(F1)toinsertacharacter. D. PressINPUT(F3)toselectanewcharacter.PressENTERtoinsertthenewcharacter totheleftofthecursor. 3. PressSTOP(F3)tomoveoutofthecharactergridandbacktotheentry. 4. PressSAVE(F4)tosavetheentryandreturntothePROTOCOLSETUPscreen. MY HOST Options:NAME(F1),IPADDR(F2) SelecttheformatofthehostpartinthelocalendpointsSIPaddress. NAME:ThehostpartintheendpointsSIPaddressisinanalphanumericformat.Use theprocedureinMYNUMBER/ALIAStocreateit. IPADDR:ThehostpartintheendpointsSIPaddressisanIPaddress.Ifused,enter anIPaddress. AUDIO FILE DELAY (SEC) Options:0(F1),1(F2),3(F3),5(F5) Thetestsetwilltransmitaudiofiles/packetsassoonasacallisestablished.Thefileswill besentcontinuously,withadelayinbetweenfiles,andwillterminatewhenthecallends. Thedelaycanbeconfiguredas0,1,3,or5seconds.

2 UDSL Module Menus

47

2.5.4 Place/Receive Calls Therearetwoversionsofthisscreen,theversion presentedisdependentonthePROTOCOLselected inthePROTOCOLSETUPscreen.Ineithercase, oneofthescreensshowninFigures44or45must be displayed in order to place or receive calls.

11:50:45 >SHOWTIME DHCP UP< PLACE/RECEIVE CALLS PROTOCOL: H.323 CODEC: G.711u GATEKEEPER : 130.131.190.21 ADDRESS TYPE: E.164 NUMBER/ALIAS 4083638000 CALL STATUS:

H.323 Place/Receive Calls ThissubsectiondescribesthesetupforH.323. PROTOCOL,CODEC,andPROXYaredisplayedin thescreenshowninFigure42,butthesesettingscanDTMF> notbechangedinthisscreen.Insteadchangethese EVENT TRANSP E.164 CALL settingsinthePROTOCOLSETUPscreens. Configurethefollowingtoplace/receiveH.323calls: Figure 42 H.323 Place/Receive Calls Screen AUDIO FILE Options:PressSELECT(F3)tochooseanaudiofile otherthanDEFAULT;otherfilesarecustomer-specific,andnotrecommended. Select the audio file to transmit. 1-DEFAULT:English-languageaudiofile;applicableforvirtuallyallcases. ADDRESS TYPE Options:TRANSP(F3),E.164(F4) Selecttheformatfortheendpointaddress. TRANSP: This address type is selected for direct peer-to-peer calls without a gatekeeper. E.164:Phonenumberaddressing,i.e.,408-363-8000. NUMBER/ALIAS DependingontheADDRESSTYPEselected,pressEDIT(more,F1)orusetheSHIFTkey andnumerickeypadtomakeanentryorpressSPEED(F3)toeitheraddorretrievefrom alistofnumbersoraliases. SIP Place/Receive Calls ThissubsectiondescribesthesetupforSIP. PROTOCOL, CODEC, and PROXY are displayed inthescreenshowninFigure43,butthesesettings cannotbechangedinthisscreen.Insteadchange thesesettingsinthePROTOCOLSETUPscreens. Configurethefollowingtoplace/receiveSIPcalls.11:50:45 >SHOWTIME DHCP UP< PLACE/RECEIVE CALLS PROTOCOL: SIP CODEC : G.711u PROXY : NONE CALL TO NUMBER/ALIAS: NAME MTT02 CALL TO HOST: IP ADDR @10 .10 .10 .12 CALL STATUS:

AUDIO FILE Options: Press SELECT (F3) to choose an audio fileotherthanDEFAULT;otherfilesarecustomerDTMF> specific,andnotrecommended. CALL EVENT NAME Select the audio file to transmit. 1-DEFAULT:English-languageaudiofile;appli- Figure 43 SIP Place/Receive Calls Screen cableforvirtuallyallcases. CALL TO NUMBER/ALIAS Options:NAME(F3)istheonlyoption. EnteranaliasonthelinebelowthislineandeitherpressEDIT(more,F1)todisplayacharacter entryscreenorpressSPEED(F3)toaddorretrievefromthelist. CALL TO HOST Options:NAME(F3),IPADDR(F4) Dependingontheselectedsetting(NAMEorIPADDR)enteraURL/IPaddressonthe linebelowthisline.YoumayalsopressSPEED(F3)toeitheraddorretrievefromalistof numbers or aliases.

48


Note:TheSIPserver(PROXY)domainnameshouldbeusedifitismanuallyenteredin thePROTOCOLSETUPscreen,otherwiseusetheSIP/PROXYIPaddress. NAME:Theentryisinanalphanumericformat.UsetheproceduregiveninSection 2.5.3 SIP, MY NUMBER/ALIAS. IPADDR:Theentryisinanumericformat. PLACE/RECEIVE CALLS Common Features CALL/HANGUP(F1):Whenreadytoplaceacall,pressCALL.ThelineunderCALLSTATUSwilldisplaythesignallingmessagesduringthecall.Whenfinished,pressHANGUP (F1).Noteinordertomakeanychangesinthesetupscreens,ortoescapefromthescreen, pressHANGUP(F1).ThefollowingF-keyisavailableduringacall: STATS(F3):Viewstatisticsonthecurrentcall,as 11:50:45 in Figure 44. This screen is only available when >SHOWTIME DHCP UP< CALL STATISTICS PROTOCOLissettoH.323. TheCALLSTATISTICSscreenreportsthefollowing: ST: 11:45:40 ET: 00:05:05 MIN MAX ST:StartTimeofthecall. JITTER: 20 20 PKT TYPE RX TX ET:ElapsedTimeofthecall. RTP: 5016 5016 JITTER MIN/MAX: The Minimum and Maximum DTMF: 0 0 SILENT: N/A 0 Jittervalues. LOST: 0 N/A Viewthenumberof(Packet)PKTTYPEReceived DROPPED: 0 N/A REPLAY: 0 N/A (RX)andTransmitted(TX)underthePKTTYPEline.REFRESH STORE CALL STATISTICS F-keys REFRESH(F1):Resetallcountersinthisscreen, Figure 44 Call Statistics Screen withoutendingthecall. STORE(F2):StoretheCALLSTATISTICSscreen.SeeSection 2.6fordetails.

Whenfinishedviewing,pressESCtoreturntothePLACE/RECEIVECALLSscreen. EVENT(F2):Viewanypastcallevents.Thescreenslisteventsalongwiththeirdirection (incoming)thattakeplaceduringacall.Press or toscrollthroughallof theavailablescreens.SeeFigure45forsampleEVENTscreens.SIP12:50:45 >SHOWTIME EVENT 12:29:01 < INVITE 12:33:58 > 180 Ringing 12:33:59 > 200 OK 12:34:00 < ACK 12:34:00 > BYE 12:34:03 < 200 OKSTORE CLEAR

H.323DHCP UP< 12:50:45 >SHOWTIME EVENT 16:31:33 H.245 masterSlaveDetermination 16:31:33 H.245 terminalCapabilitySetAck 16:31:33 >H.245 masterSlaveDeterminAck 16:31:48 >CS connect 16:31:48 SHOWTIME EVENT 12:29:01 ---- SIP Call Ended ----

DHCP UPSHOWTIME EVENT

DHCP UPSHOWTIME EVENT

DHCP UPH.245 openLogicalChannel 16:31:48 H.245 openLogicalChannelAck 16:32:43 >H.245 endSessionCommand 16:32:43 CS releaseCompleteCLEAR STORE CLEAR

16:32:45 ---- H.323 Call Ended ----

STORE

STORE

CLEAR

Figure 45 Event Screens STORE(F2):StoretheEVENTscreens.SeeSection 2.6fordetails. CLEAR(F4):Clearthelistofevents. PressESCtoreturntothePLACE/RECEIVECALLSscreen.2 UDSL Module Menus 49

SPEED(F3)isavailableintheNUMBER/ALIASparameterfieldofH.323andintheCALL TONUMBER/ALIASparameterfieldofSIP.SPEEDprovidesmemoryrecallofnumbers, names,oraliases.Usethisprocedure: 1. Useanypreviouslydescribedproceduretomakeanumeric/alphanumericentryinany fieldthatdisplaysaSAVEF-key. 2. PressSAVEandaSPEEDDIALlistisdisplayed,notethattheCURRENTlinecontains thenewentry. 3. Press or toselectablanklineandpressPASTE(F1)tocopytheCURRENTentry totheblankline.Upto10entriescanbesaved.Ifalinewithanentryisselected,itwill beoverwritten.Afteranentryismade,twoF-keysareavailable: SELECT(F2):SelectanentryfromtheSPEEDDIALlistandpressCALL(F2).The PLACE/RECEIVEscreenisthendisplayed. DELETE(F3):Deleteaselectedentry.

50


2.5.5 VQ Measurements The menu contains: NON-INTRUSIVEVQMMEASUREMENT 2.5.5.1 Non-intrusive VQM Measurement Configurethefollowing: METRICS REPORTING Options:ENABLE(F1),DISABLE(F2) IfENABLED,theENDPOINTCALLMETRICscreens willbeusedtomeasurevoicequalityreceivedfrom thenetworkinterface.11:50:45 >SHOWTIME DHCP UP< VQ MEASUREMENT SETUP METRICS REPORTING TRIGGERED BY IN EVERY FOR : : : : ENABLE TIMER 5 SEC 300 SEC

TRIGGERED BY Options:TIMER(F1),F-KEY(F2) ChoosethetriggeringmethodifMETRICSREPORTINGisENABLED. TIMER: A Timer trigger is used when a report ENABLE DISABLE HST RPT needs to be generated repeatedly in a set time interval,e.g.refreshtheon-screenreportinevery Figure 46 VQ Measurement 10secondsfor50seconds.Ifused,configurethe Setup Screen INEVERYandFORsettings. F-KEY:Ifselected,triggerareportbypressingRPTKEY(F1)intheENDPOINTCALL METRICSreportscreen. IN EVERY IfusingtheTIMERsetting,selectasampletimeof5to300secondsin5secondincrementsusing+(F2)or-(F3). FOR IfusingtheTIMERsetting,selectanendofreportsamplingtimeof5to300secondsin5 secondincrementsusing+(F2)or-(F3),orselectCALLEND(F1)toendthereportsamplingattheendofthecall. VQ MEASUREMENT SETUP F-key HST RPT(F4):Viewanyterminatedcallmetricreports.SeeSection 2.5.5.2. Whenfinishedwiththeconfiguration,pressESC. 2.5.5.1.1 Non-intrusive Report ScreensTimed Trigger20:48:59 >SHOWTIME DHCP UP< ENDPOINT CALL METRICS RPT TIME:20:48:32 STAT: ACTV SRC: 10.10.10.11 UDP: 50000 DST: 10.10.10.12 UDP: 50000 ACTUAL IDEAL LQ-R: 93 94 CQ-R: 92 94 GAP-R: 92 94 BURST-R: 92 94 MOS-LQ: 4.20 4.20 MOS-CQ: 4.18 4.20 MOS-PQ: 4.27 4.40

F-Key Trigger20:48:59 >SHOWTIME DHCP UP< ENDPOINT CALL METRICS RPT TIME: STAT: READY SRC: 10.10.10.11 UDP: 50000 DST: 10.10.10.12 UDP: 50000 ACTUAL IDEAL LQ-R: 93 94 CQ-R: 92 94 GAP-R: 92 94 BURST-R: 92 94 MOS-LQ: 4.20 4.20 MOS-CQ: 4.18 4.20 MOS-PQ: 4.27 4.40

STORE

RPT KEY

STORE

Press F1 to update screen.

Figure 47 Endpoint Call Metric Screens Oncethetestsetisconfiguredforacall,pressCALL(F1)inthePLACE/RECEIVECALLS screen. Whenthecallhasbeenaccepted,theVQRPT(F4)F-keyisavailable.Pressittodisplay theVOICEQUALITYREPORTSselectionscreen. SelectareportandpressENTER.OneofthefollowingscreensdependingontheTRIGGEREDBYselectionisthendisplayed:2 UDSL Module Menus 51

Thesescreensreportthefollowing: RPT TIME:Currentreporttimestamp.IntheF-KEYtriggermode,RPTTIMEdisplaysthe timestampwhentheRPTKEY(F1)ispressedforareport. STAT:Reportscreenstatusthatindicatesoneofthefollowingstates: ACTV:Aneventreportingtimerisactive. ENDED:Alltimertriggeredreportsaredone. READY:Noactivetimer,butRPT(F1)isactive. INACT:NeithertimernorreportF-keyisactive. SRC:SourceIPaddressofthecall. SRC UDP: User Datagram Protocol port number assigned at the source endpoint. DST:DestinationIPaddressofthecall. DST UDP: User Datagram Protocol port number assigned at the destination endpoint. Thefollowingisreportedforeachcallalongwiththeidealbestresultnumber: LQ-R:R-factorvalueofListeningQuality. CQ-R:R-factorvalueofConversationalQuality. GAP-R: R-factor value in GAP mode. GAP mode indicates voice quality in a relatively good condition. BURST-R:R-factorvalueinBURSTmode.BURSTmodeindicatesvoicequalityinarelativelyworsecondition. MOS-LQ:MeanOptionScoreofListeningQuality. MOS-CQ:MeanOptionScoreofConversationalQuality. MOS-PQ:AnequivalentPESQMOSscoremappingfromtheR-factor. ENDPOINT CALL METRICS Screen F-keys RPT KEY(F1):ThisisavailableifF-KEYwasselectedasaTRIGGER.Useittotakea sampletogenerateareportasinFigure47. STORE(F2):Savethereport.SeeSection 2.6fordetails. Afterthecallhasended,pressHSTRPT(F4)intheVQMEASUREMENTSETUPscreen toviewtheTERMINATEDCALLMETRICSscreendescribedinSection 2.5.5.2. 2.5.5.2 Terminated Call Metrics Screen TheTERMINATEDCALLMETRICSscreenisdis11:50:45 playedbypressingHSTRPT(F4)intheVQMEA>SHOWTIME DHCP UP< SUREMENTSETUPscreen,showninFigure46.It TERMINATED CALL METRICS reportsR-factorsandMOSofthecalljustendedas CALL PEER: wellastherangeofvoicequalityscoressincethe MTT01 LAST MIN AVG MAX testsetwaspoweredon. LQ-R:93 93 93 93 TheTERMINATEDCALLMETRICSscreenreports CQ-R:92 92 92 92 MOS-LQ:4.20 4.20 4.20 4.20 thefollowing: MOS-CQ:4.18 4.18 4.18 4.18 CALL PEER:Reportstheotherpartyofthecall. MOS-PQ:4.27 4.27 4.27 4.27 Forthefollowingfiveitems,thescreenreportsthe Last,Minimum,Average,andMaximumvalues. CLEAR STORE LQ-R:R-factorvalueofListeningQuality. CQ-R:R-factorvalueofConversationalQuality. Figure 48 Terminated Call MOS-LQ:MeanOptionScoreofListeningQuality. Metrics Screen MOS-CQ: Mean Option Score of Conversational Quality. MOS-PQ:AnequivalentPESQMOSscoremappingfromtheR-factor. TERMINATED CALL METRICS Screen F-keys: CLEAR(F1):Erasethecurrentrecord. STORE(F2):Storethereport.SeeSection 2.6fordetails. Whenfinishedviewingthisscreen,pressESC.

52


2.6 View/Store/PrintUsethisscreentomanage,view,andprintstored results. VIEW/STORE/PRINT F-keys VIEW(F1):Viewaselectedfile,seeSection 2.6.3. SAVE(F2):Storeresults,seeSection 2.6.1. PRINT(F3):Printaselectedfile,seeSection 2.6.4. RENAME (more, F1): Displays a character entry screen, shown in Figure 50, which allows you to renameastoredtest,seeSections 2.6.1 and 2.6.2. UN/LOCK(more,F2):Lockandunlockaselected file,seeSection 2.6.6. DELETE(more,F3):Deleteaselectedunlockedfile, see Section 2.6.5. 2.6.1 Saving a Test10:50:10 VIEW/STORE/PRINT Free space: 45355 kbyte NAME TYPE LOCK 1. UDSL0001 UDSL 2. UDSL0002 UDSL 3. 4. 5. 6. 7. 8. 9. 10. VIEW SAVE PRINT more

RENAME

UN/LOCK DELETE

more

Figure 49 View/Store/Print Screen 1. FromanyscreenwithaSTOREF-key,pressitandyourtestissavedwithageneric filenameasaCSVfilethatcanbeopenedwithmostspreadsheetprograms.Thesefiles arestoredintheMMCcardunderRESULT>CSV.

2.6.2 Renaming a Stored Test 1. Fromthemodulesmainmenu,selectVIEWTEST 11:50:45 RESULT. VIEW/STORE/PRINT 2. Selectthedesiredfilewith or . PressUN/LOCK(more,F2)ifthelockiconindiFILENAME: UDSL001 catesthatthefileislocked. 3. PressRENAME(F1)andacharacterentryscreen A a B b C c D d E e F f (Figure50)isdisplayed. G g H h I i J j K k L l 4. PressINPUT(F3).TheAishighlightedandthe M m N n O o P p Q q R r S s T t U u V v W w X x INPUTF-keyhaschangedtoSTOP. Y y Z z 0 1 2 3 4 5 6 7 5. Use , , ,or to select a desired character. 8 9 - _ @ ! # $ % & 6. PressENTERtoplacethedesiredcharacterinthe INSERT DELETE INPUT SAVE label.ContinuethisprocessuntiltheFILENAME label is complete. Up to 15 characters can be Figure 50 Character Entry Screen entered. Ifamistakeismade: A. PressSTOP(F3). B. MovetheFILENAMEcursortotheincorrectcharacter. C. PressDELETE(F2)todeleteor,pressINSERT(F1)toinsertacharacter. D. PressINPUT(F3)toselectacharacter. E. Use , , ,or to select a desired character. F. PressENTERtoinsertthenewcharactertotheleftofthecursor. 7. PressSAVE(F4)toreturntotheVIEW/STORE/PRINTscreen(Figure49).

2 UDSL Module Menus

53

2.6.3 Viewing a Stored Test 1. 2. 3. 4.

Fromthemodulemainmenu,selectVIEW/PRINTRESULTS. Selectthedesiredfilewith or andpressVIEW(F1)andthestoredresultwillappear. Use or to scroll through the available screens. Whenfinished,pressESC.

2.6.4 Printing a Stored Test 1. ConnectaSunSetprintertotheserialportofthetestset. For other types of printers or for more information, refer to the Storing and Printing chapterinthetestsetusersmanual. 2. Fromthemodulemainmenu,selectVIEW/PRINTRESULTS. 3. Selectthedesiredfilewith or andpressPRINT(F3).Thefilewillbeginprinting. 4. Whenfinished,pressESC. 2.6.5 Deleting a Stored Test 1. Fromthemodulemainmenu,selectVIEW/PRINTRESULTS. 2. Selectthedesiredfilewith or andpressDELETE(more,F3).Thefileisdeletedif unlocked. 3. Whenfinished,pressESC. 2.6.6 Locking and Unlocking a Stored Test 1. Fromthemodulemainmenu,selectVIEW/PRINTRESULTS. 2. Selectthedesiredfilewith or andpressUN/LOCK(more,F2)andthefileislocked orunlockedasindicatedtotherightofthefilename.Refertothelockiconshownin Figure49. 3. Whenfinished,pressESC.

54


2.7 ProfilesUse the Profile function to store commonly used module configuration settings. The PROFILE LIST screen contains a DEFAULT profile.Thisprofileisbasedonthefactorystandard configurationofthismodule. To create other profiles, change the configuration settings in any available screens. Once all configurationscreensarechangedasdesired,select PROFILESfromthemodulesmainmenuandselect ablankentry.PressSTORE(F2)andthesettings aresavedwithagenericfilename.Usethisscreen to manage profiles. The screen and its functions areasfollows: Note:TheDEFAULTfilecannotbedeletedorunlocked.11:50:45 >SHOWTIME PROFILE LIST Free space: 113729 kbyte FILENAME LOADED MODULE LOCK 1.DEFAULT NO UDSL 2.P00001 NO UDSL 3.SANTA ROSA YES UDSL 4. 5. 6. 7. 8. 9. 10. LOAD STORE RENAME more

DELETE

LOCK

more

Figure 51 Profile List Screen PROFILE LIST Screen F-keys LOAD (F1): Change all configuration settings of themoduletomatchtheselectedprofile.TheLOADEDcolumnchangesfromNOtoYES. STORE(F2):Saveallcurrentconfigurationscreenswithagenericfilename.Currently10 profilescanbesaved.ThetypeofmoduleisindicatedintheMODULEcolumn. RENAME(F3):SelectafilenameandpressRENAME(F3)tochangeitsname.Acharacter entry screen is displayed. Use the procedure in Section 2.6.2toeditthenamefromstep4. DELETE(more,F1):Deleteaselectedunlockedprofile. LOCK/UNLOCK(more,F2):Lockorunlockaselectedfile.Lockaprofiletopreventchanges. ThefilesstatusisindicatedbyalockiconintheLOCKcolumn.InFigure51DEFAULT islocked.

3ApplicationOverview

55

2.8 UtilityThis menu contains: MODULEINFORMATION UPDATESOFTWARE 2.8.1 Module Information The MODULE INFORMATION screen provides moduleinformation.Somehighlights: ETH MAC ADDR:10/100PortMediaAccessControl Address.Inthiscase,itis00:10:9E:00:A5:2C. AWARE APP REV:WhencontactingSunriseTelecom Customer Service, this information may be requested.Inthiscase,itis3.1.0.4. AGENT APP REV:WhencontactingSunriseTelecom Customer Service, this information may be requested.Inthiscase,itis1.00.001.11:50:45 >SHOWTIME CPE MODE:N/A VDSL PROFILE:N/A MODULE INFORMATION IP UPNON-INTRUSIVE VQMandthefollowing: METRICSREPORTING:ENABLE TRIGGEREDBY:TIMER INEVERY:5SEC FOR:300SEC Whenfinished,pressESCtwice. 3. FromtheVOIPMAINMENU,selectPLACE/RECVCALL. 4. PressCALL(F1)toplaceacall. 5. Oncethecallisconnected,pressVQRPT(F4). 6. FromtotheVOICEQUALITYREPORTscreen,selectENDPOINTCALLMETRICS. Note:PressingESCwillterminatethereportbeforetheactivereportingtimelimit(default is300seconds). 7. Whenthecallisended,theTERMINATEDCALLMETRICSreportscreen(i.e.,History Report)isavailableintheNon-intrusiveVQMEASUREMENTSETUPscreenbypressingHSTRPT(F4).Thisreportshowsthevoicequalityofthejustendedcallaswellas themaximum,minimum,andaveragescoressincethetestsetwaspoweredon.

62


4 General Information 4.1 Testing and Calibration StatementSunriseTelecomcertifiesthatthisproductwasmanufactured,tested,andverifiedaccordingtotheapplicableSunriseTelecomIncorporatedmanufacturingandtestprocedure(s). These formal procedures are designed to assure that the product meets its required specifications. Thisproducthasnouser-adjustablesettings.Duringnormalusage,periodiccalibrationis notarequirement.However,iftheproductfailsduringtheself-verificationtest,duringpower up,theproductcanbereturnedtothemanufacturerforevaluationandrepair.

4.2 Customer ServiceGeneralSunriseTelecomCustomerServiceisavailablefrom7:30AMto5:30PMPacific StandardTime(California,U.S.A.). CustomerServiceperformsthefollowingfunctions: Answerscustomerquestionsoverthephoneonsuchtopicsasproductoperationand repair. Facilitatespromptrepairofmalfunctioningtestsets. Providesinformationaboutproductupgrades. AReturnMerchandiseAuthorization(RMA)Numberisrequiredbeforeanyproductmaybe shippedtoSunriseTelecomforrepair.Out-of-warrantyrepairsrequirebothanRMAanda PurchaseOrderbeforetheunitisreturned.Allrepairsarewarrantedfor90days. Contact Customer Service at: SunriseTelecomIncorporated 302EnzoDrive SanJose,CA95138 U.S.A. Tel: 1-800-701-5208 Fax:1-408-363-8313 Internet:www.sunrisetelecom.com E-mail:[email protected] OrcontactoneourofficeslistedinSection 4.3.

4.3 OfficesSunrise Telecom Contact Information For more information, please call +1-800-701-5208 or +1-408-363-8000, or visit www. sunrisetelecom.com SunriseTelecomofficesarelocatedaroundtheworld. SUNRISETELECOMINCORPORATED 302EnzoDriveSanJose,CA95138U.S.A. Tel:1-800-701-5208Fax:1-408-363-8313 Internet:http://www.sunrisetelecom.com E-mail:[email protected] 4GeneralInformation

SUNRISETELECOMATLANTA 3075NorthwoodsCircle,Norcross,GA30071,USA Tel:770-446-6086,Fax:770-446-6850 [email protected] SUNRISETELECOMCHINA Room1503,Tower3,No.1,XizhimenwaiStreet XichengDistrict,Beijing,100044,CHINA Tel:+86-10-5830-2220,Fax:+86-10-5830-2239 [email protected]

SUNRISETELECOMFRANCESAS ZACourtaboeuf2-ImmeubleleCeylan 6AlledeLondres91140Villejust,FRANCE Tel:+33(0)169938990,Fax:+33(0)169938991 [email protected] SUNRISETELECOMGERMANY Grabenstrasse1,72116MssingenGERMANY Tel:+4974733782400Fax:+49(0)74733782424 [email protected] SUNRISETELECOMTAIWAN 21,WuChuan3rdRoad,Wu-KuHsiang TaipeiCounty,248,Taiwan,R.O.C. Tel:+886-2-5578-0788,Fax:+886-2-2298-2575

4.4 Express Limited WarrantyThisSunriseTelecomproductiswarrantedagainstdefectsinmaterialsandworkmanship duringitswarrantyperiod.Thewarrantyperiodforthisproductiscontainedinthewarranty pageonhttp://www.sunrisetelecom.com. SunriseTelecomagreestorepairorreplaceanyassemblyorcompo entfoundtobedefecn tiveundernormaluseduringthisperiod.Theobligationunderthiswarrantyislimitedsolely torepairingorreplacingtheproductthatprovestobedefectivewithinthescopeofthewarrantywhenreturnedtothefactory.Thiswarrantydoesnotapplyundercertainconditions, assetforthonthewarrantypageonhttp://www.sunrisetelecom.com. Pleaserefertothewebsiteforspecificdetails. THIS IS A LIMITED WARRANTY AND THE ONLY WARRANTY MADE BY SUNRISE TELECOM.SUNRISETELECOMMAKESNOOTHERWARRANTY,REPRSENTATION ORCONDITION,EXPRESSORIMPLIED,ANDEXPRESSLYDISCLAIMSTHEIMPLIED WARRANTIESOFMERCHANTABILITY,FITNESSFORAPARTICULARPURPOSEAND NON-INFRINGEMENTOFTHIRDPARTYRIGHTS.

64


IndexA Applications IPTVSTBEmulationatDSLInterface;58 IPTVSTBEmulationattheEthernetInterface;58 TestingaDSLLine;57 VODSTBEmulationatDSLInterface;59 VODSTBEmulationattheEthernetInterface;59 VoIPH.323PhoneCalltoaPSTN(POTS)Device;61 VoIP,H.323PhoneCallwithaGatekeeper;61 VoIP,H.323PhoneCallwithoutaGatekeeper;60 VoIP,Non-IntrusiveVoiceQualityMeasurement;62 VoIP,PlacingorReceivinganH.323Call;60 VoIP,PlacingorReceiv

sunrise telecom ssmtt 48 (udsl) manual

Documents

udsl module ssmtt

electronic equipment

electronic equipment

disposal of electrical

supplied equipment

disposal of waste electrical

udsl menus

module connector panel