summit cc & fm cc & fm ccfm_brochure.pdf · frame mounted pump - model fm frame mounted...
TRANSCRIPT
Summit CC & FM
Close Coupled &Frame Mounted Pumps
0
A25
8
1750 R
PM
US Gallons Per Minute
Head
in
Feet
6X8-16
4X5-143X4-14
2.5X4-14
1.5X2-12
2X2.5-12
2X2.5-10
2.5X3-10
3X4-8
3X4-103X4-12
4X5-125X6-12
4X5-10
4X5-8
4X5-7
5X6-10
6X8-12G
6X8-12
1X2-8
1X2-8G1.5X2-8
1.5X2-8G
1.5X2-6J1X2-6
1.5X2-6
30
10
60
110
160
210
260
310
530 1030 1530 2030 2530 3030 3530 4030
2X2.5-6
2X2.5-8
US Gallons Per Minute
3500 R
PM
Head
in
Feet
20
40 240 440 640 840 1040 1240 1440
70
120
170
220
270
320
370
420
470
2.5X3-11
2.5X3-8
1X2-8
1X2-8G
2X2.5-81.5X2-8G
1X2-61.5X2-6
1.5X2-6J
2X2.5-6
1.5X2-8
3X4-8
4X5-7
4X5-11
Maximum Working Pressures
Maximum Working Pressure Liquid Temperatures
175 PSIG
165 PSIG
155 PSIG
0°F – 15°F
151°F – 200°F
201°F – 250°F
CC & FM
Close Coupled & Frame Mounted Pumps
Mechanical Seals
Heavy Duty Shaft
Enclosed Impeller
Replaceable Wearing Rings
Vertical Split Casing DesignBearings
Summit CC & FM pumps are horizontal, end suction, centrifugal pumps designed for general service such as water, solvents, light oils, non-corrosive chemicals, coolants and brines. Available in capacities to 2300 GPM and heads to 200 feet, these pumps are an economical and dependable solution for your pumping needs. All flanges are 125lb ANSI B16.1 rating, NPT connections are standard on 6" and 8" sizes. A renewable bronze shaft sleeve is standard on cast iron pumps, and a 316SS shaft sleeve is standard on alloy pumps.
Close Coupled Pump - Model CCThe close coupled pump is directly mounted to a NEMA "C" face motor, and designed to use minimal space. Motors with TEFCframes use a standard mechanical seal (JM frame), or packing(JP frame). ODP motors, and stainless steel shafts are optional.
Frame Mounted Pump - Model FMFrame mounted pumps are constructed with a rigid bearing frame, flexibly coupled, and mounted on a fabricated steel base with optional drip pan. Casings, adaptors, and bearing frames share mating registers for maximum interchangeability. Coupling guards meet ASME B 15.1 specifications.
Interchangeable PartsComponent parts, of similar sizes, are interchangeable between frame mounted and close coupled pumps. This means less spare parts inventory and fast delivery of required parts.
Bronze wear rings are easily replaced and prevent casing wear. Rings are not required on 316SS wet ends.
An MG9 seal is standard; constructed of Carbon vs. Ni-resist faces,viton elastomers and stainless steel metal parts. The maximum operating temperature rating is 250°F. Packing is optional.
Frame mounted pumps use a rigid 4140 steel shaft designed to maximize seal and bearing life with a maximum deflection of .002".
Back pull out design allows maintenance of bearing frame without disturbing the suction and discharge piping. Eight casing discharge positions are possible.
Frame mounted pumps have regreaseble SKF single row deep groove ball bearings with a minimum B-10 life of 20,000 hours.
The enclosed impeller ensures the highest efficiency, and is hydraulically balanced which reduces axial thrust, and increases bearing life. The impeller is keyed and locked to the shaft.
Seal KitsEconomically priced complete seal kits are available to help minimize inventory.
316SS wet ends are available for corrosive applications. All wetted surfaces are constructed of 316SS including: Casing, Impeller, Adaptor, Shaft, Sleeve, Washer, Impeller Screw, and Key.