stress in rock
TRANSCRIPT
![Page 1: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/1.jpg)
STRESS
BY ANKUR SAHAY
REG NO:-16MT001278
![Page 2: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/2.jpg)
INTRODUCTION
• STRESSIt is the internal resistance of the metal/rock /soil specimen offered against loading or deformation.
• UNIT N/mm2 or Mpa
• STRENGTHMaximum value of stress at which material fails.
![Page 3: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/3.jpg)
DIFFERENT KINDS OF STRESS ON ROCK Lithostatic stress:Rock beneath the Earth's surface experiences equal pressure exerted on it from all directions because of the weight of the overlying rock. It is like the hydrostatic stress (water pressure) that a person feels pressing all around their body when diving down deep in water
Differential (deviatoric) stress: In many cases, rock may experience an additional,unequal stress due to tectonic forces. There are three basic kinds. tensional stress (stretching) compressional stress (squeezing) shearing stress (side to side shearing)
![Page 4: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/4.jpg)
Strain - Rock Deformation in Response to Stress:-Rock responds to stress differently depending on the pressure and temperature (depth in Earth) and mineralogic composition of the rock.
Elastic deformation: For small differential stresses, less than the yield strength, rock deforms like a spring. It changes shape by a very small amount in response to the stress, but the deformation is not permanent. If the stress could be reversed the rock would return to its original shape.
![Page 5: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/5.jpg)
Brittle deformation: Near the Earth's surface rock behaves in its familiar brittle fashion. If a differential stress is applied that is greater than the rock's yield strength, the rock fractures, it breaks. Note: the part of the rock that didn't break springs back to its original shape. This elastic rebound is what causes earthquakes.
Ductile deformation: Deeper than 10-20 km the enormous litho static stress makes it nearly impossible to produce a fracture (crack - with space between masses of rock) but the high temperature makes rock softer, less brittle, more malleable. Rock undergoes plastic deformation when a differential stress is applied that is stronger than its yield strength. It flows. This occurs in the lower continental crust and in the mantle
![Page 6: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/6.jpg)
STRESS STRAIN CURVE FOR DUCTILE MATERIAL
![Page 7: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/7.jpg)
YOUNG’S MODULUS A measure of elasticity, equal to the ratio of the stress acting on a substance to the strain produced.
ELASTIC LIMIT The maximum extent to which a solid may be stretched without permanent alteration of size or shape.
PLASTIC REGION If a material is forced beyond the elastic region, it experiences plastic deformation.
ULTIMATE STRENGTHIt is the capacity of a material or structure to withstand loads tending to elongate, as opposed to compressive strength, which withstands loads tending to reduce size.
RESILIENCE is the ability of a material to absorb energy when it is deformed elastically, and release that energy upon unloading.
PROOF RESILIENCE is defined as the maximum energy that can be absorbed within the elastic limit, without creating a permanent distortion.
TOUGHNESSIt is the maximum strain energy which can be stored in material before fracture.
![Page 8: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/8.jpg)
DUCTILITY is a solid material's ability to deform under tensile stress; this is often characterized by the material's ability to be stretched into a wire.
BRITTLENESS A material is brittle if, when subjected to stress, it breaks without significant deformation.
Malleability is the quality of something that can be shaped into something else without breaking, like the malleability of clay. CREEP –It is a plastic deformation which is permanent in nature and it occurs with time at constant loading.
Fatigue is the weakening of a material caused by repeatedly applied loads. It is the progressive and localised structural damage that occurs when a material is subjected to cyclic loading.
![Page 9: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/9.jpg)
3-D STRESS ELEMENTStress is a tensor quantity means it is bidirectional.
In 3-D stress element, there are 9 stress component can be expressed in the form of matrix.
In 2-D loading there will be only 4 stress elements.
![Page 10: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/10.jpg)
![Page 11: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/11.jpg)
ELASTIC CONSTANT1. MODULUS OF ELASTICITY OR YOUNG’S MODULUS
Ratio of stress to strain within the elastic limit is a constant which is defined by Hooke as the Modulus of elasticity or Young’s modulus (E).
2. SHEAR MODULUS OR MODULUS OF RIGIDITYDenoted by G, or sometimes S , is defined as the ratio of shear stress to
the shear strain.
3. BULK MODULUS(K) It is defined as the ratio of direct stress and volumetric strain.
4. POISSON’S RATIO Defined as the ratio of lateral strain and longitudinal strain.
![Page 12: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/12.jpg)
INTER RELATIONSHIP B/W ELASTIC CONSTANTS
![Page 13: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/13.jpg)
UNCONFINED COMPRESSIVE STRENGTH OF ROCK SAMPLE
![Page 14: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/14.jpg)
![Page 15: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/15.jpg)
![Page 16: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/16.jpg)
SHEAR STRENGTH OF ROCK The compressive strength of rock is a function of the confining pressure. As the confining pressure increases so does the strength. The variation of peak stress with confining pressure is referred as rock criterion of failure.The simplest and the best known method is Mohr Coulomb criterion : the linear approximation of variation of peak stress with confining pressure.
![Page 17: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/17.jpg)
MOHR CIRCLE
• Graphical construction that visualize the relationship between the principal stresses and tractions on a boundary (like a fault).
![Page 18: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/18.jpg)
![Page 19: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/19.jpg)
![Page 20: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/20.jpg)
COULOMB LAW OF FAILURE
t
c
sn
Coulomb equation tc = c + tan f sn
Where,tc = critical shear stress required for faulting (shear strength)
c = cohesive strength
tan f = coefficient of internal friction = m
f
![Page 21: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/21.jpg)
MOHR-COLOUMB FAILURE CRITERION
![Page 22: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/22.jpg)
MOHR STRESS DIAGRAM
a) Mohr circle radius = ½(s1 – s3] that is centered on ½(s1 + s3] from the origin.
b) The Mohr circle radius, ½(s1 - s2] is the maximum shear stress ss max.
c) The stress difference (s1 – s3), called differential stress is indicated by sd
![Page 23: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/23.jpg)
BYERLEE'S LAWByerlee's law, also known as Byerlee's friction law concerns the shear stress (τ)
required to slide one rock over another.
For a given experiment and at normal stresses (σn) below about 200 MPa the shear
stress increases approximately linearly with the normal stress (τ = 0.85 σn) and is highly
dependent on rock type and the character (roughness) of the surfaces . Byerlee's law states
that with increased normal stress the required shear stress continues to increase, but
the rate of increase decreases (τ = 0.5 + 0.6 σn), and becomes nearly independent of rock
type.
The law describes an important property of crustal rock, and can be used to
determine when slip along a geological fault takes place.
![Page 24: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/24.jpg)
![Page 25: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/25.jpg)
![Page 26: Stress in rock](https://reader035.vdocuments.us/reader035/viewer/2022081514/58f1b23d1a28ab013a8b45a7/html5/thumbnails/26.jpg)
THANK YOU