strain link stick roller link stick · t401-2265 trunnion gauge for 3/4" acme threads .5 lb...
TRANSCRIPT
TRANSMISSION TOOLS
ROLLER LINK STICKSTRAIN LINK STICK
Cat.No. O.A.Lgth
PoleDia & Lgth
Jaw OpeningMin Max
WorkLoadLbs.
WgtLbs.
H4716-1 3"-3" 1.5"x2' .44 1.06 6,500 4.75
H4716-2 4'-9" 1.5"x4' .44 1.06 6,500 5.75
H4716-3 6'-9" 1.5"x6' .44 1.06 6,500 6.75
H4716-4 8'-9" 1.5"x8' .44 1.06 6,500 7.75
H4716-5 10'-9" 1.5"x10' .44 1.06 6,500 8.75
H4716-6 12'-9" 1.5"x12' .44 1.06 6,500 9.75
H4717 5' 1.5"x4' .72 1.50 6,500 9.875
H4717-1 7'-2" 1.5"x6' .72 1.50 6,500 11.875
H4718 5'-2" 1.5"x4' 1.00 2.50 6,500 11.125
H4718-1 7'-2" 1.5"x6' 1.00 2.50 6,500 13
H4718-2 9'-2" 1.5"x8' 1.00 2.50 6,500 15
H4718-3 11'-2" 1.5"x10' 1.00 2.50 6,500 17
H4718-4 13'-2" 1.5"x12' 1.00 2.50 6,500 19
ADJUSTABLE STRAIN POLES
Cat. No. DescriptionMaxVoltg
InsulatdSection
O.A.Lgth
WgtLbs.
C401-2144 6' Strain Pole 72.5kV 36" 7'-8" 18C401-2145 7' Strain Pole 169kV 48" 8'-8" 18.75C401-2146 8' Strain Pole 242kV 63" 9'-11" 19.5C401-2147 10' Strain Pole 302kV 84" 11'-8" 20.87C401-2215 12' Strain Pole 362kV 102" 13'-2" 22.25C401-2148 14' Strain Pole 552kV 135" 15'-11" 23.75C401-2149 18' Strain Pole 765kV 180" 19'-8" 26.5
AccessoriesE401-0138P 2" Adjustable Pole Clamp 2E401-1998P 12' Acme-thread Strain Jack 3V401-0157P 24' Acme-thread Stain Jack 4V401-0158 36" Acme-thread Strain Jack 6E401-1510P Steel Through Pin .375
059738P Klik Pin .06
SPIRAL LINK STICK
Cat. No. Length Pole Dia. x Length Max. Conductor Work
LoadH4722 27.5” 1.25” x 15.4” 1510.5 kcmil ACSR 3500 lb.C400-0812 57.5” 1.25” x 42” 1510.5 kcmil ACSR 3500 lb.
Tran
smis
sion
Too
ls
• Used as insulation between rope blocks and a hot line wire grip
• For deadend structures and running corners• Attached to conductor close to wire tong to sup-
port conductor loads• Also used to support middle conductor on H
frame structures during insulator or crossarm changes
• Replaces strain link stick when lineman cannot safely install one by hand
• A lifting eye on the head ferrule enables the line-man to guide the spiral link stick to the conductor with a hotstick
• 1-1/14" Epoxiglas pole
• For spreading and holding conductors at midspan when relocating a pole
• Applied to conductor at pole and pulled to posi-tion by hand line on butt ring
• Handline should be secured by a temporarily in-stalled screw anchor or other fixed object
• Rotating the pole closes the hook, leaving head free to roll along conductor
Cat. No. Length Pole Dia. x Length Max. Conductor Work
LoadH4714-4 58" 1.25" x 4' 605 kcmil ACSR 1000H4714-6 82" 1.25" x 6' 605 kcmil ACSR 1000
• For many transmission and EHV maintenance ap-plications
• Helps support conductors while insulators are removed
• Used with yoke plates and hook assemblies at the conductor
• Five stainless steel crosspins are located at 6" intervals on the 2" diameter Epoxiglas poles
• 12" Strain Jack included with each Strain Pole
E401-0138P
172HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com
Cat. No. C401-0095• Used with two pole strain carriers, these units grip
compression sleeves over the compressed area, requir-ing no shoulder or adapter to pull against
• 11,000 lb max load (with 2" adjustable strain poles)• Includes a hot link extension for 3/4" & 1" dia shank
and 4 sets of shoes for conductor 477-1351 MCM ACSR
TAKE-UP TRUNNIONS
HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com
TRANSMISSION TOOLS
173
TRANSMISSION TOOLS
E401-2066P E401-2068P
Transmission Tools
HEAVY DUTYTWO-POLE STRAIN CARRIERS
• Relieve strain from an insulator string to permit removal from energized lines
• Normally used on a single string of insulators• Also used for multiple strings where conductor
end hardware permits attachment• Max load rating is 15,000 lb per insulator string
Cat. No. PoleLength
Distance Between Yokes Weight
C401-2174 6' 49" - 81" 81 lbC401-2175 7' 59" - 93" 83 lbC401-2176 8' 74" - 108" 85 lbC401-2177 10' 95" - 129" 89 lbC401-2216 12' 113" - 147" 95 lbC401-2178 14' 146" - 180" 97 lbC401-2179 18' 191" - 225" 105 lb
STD DUTY STRAIN CARRIERS
• Same basic use as the two pole strain carrier• Distribution strain carrier has a compression
deadend yoke at the hot end• Max load rating is 6,500 lb per insulator string
Cat. No. PoleLength
Distance Between Yokes Weight
C401-0411 6' 47.5" - 81" 82 lbC401-0410 8' 71.5" - 105" 92 lb
TWO-POLE STRAIN CARRIERACCESSORIES
Cat. No. Description WeightC401-1720 Conductor End Yoke Assembly
(includes hook and socket)25 lb
C401-1721 Structure End Yoke Assembly(includes chain and attach. hardware)
20 lb
• Can be ordered separately to make two pole strain carriers.
• Fabricated of high strength aluminum plate• Max load rating 15,000 lb per insulator string
TWO-POLE YOKES
DEADEND COMPRESSION YOKE ASSEMBLY
C401-1720 C401-1721
Cat. No. Description WeightE401-2066P (1) Large Trunnion 3.5 lbE401-2068P (1) Small Trunnion 2 lbT401-2265 Trunnion Gauge for 3/4" acme threads .5 lb
• Bronze alloy and ball thrust bearing construction • Equal the capacity of all Chance yokes• Requires M19483 Ratchet
T401-2265DEADEND SOCKET
Cat. No. C401-1184• Furnished with the two
pole strain carrier• For extension links with
7/8" shank and 1.5" collar
TRANSMISSION TOOLSTr
ansm
issi
on T
ools SINGLE-POLE STRAIN CARRIER
YOKES
Cat. No. Fits Yoke Plates WgtC401-1719 Flat Plates up to 3/4" thick 25 lbs.
C401-1718 Flat Plates up to 1" thick 25 lbs.
C401-1717 Rectangular or Triangular Plates up to 3/4" thick
25 lbs.
• Can be used with adjustable strain poles to remove the strain from one string of multiple strings of deadend insulators
• Should be purchased in pairs to fit specific yoke plate construction
• Same yoke assemblies can be used on both the hot and cold end of tne insulator string as they hook into the yoke plate hardware
• Rated at 15,000 lb max load per insulator string
STRAIN POLES
• For bundle conductor yoke plates• Accommodate a wide range of yoke plate
designs and hole spacings• Commonly used in deadend rigging, for "V"
strings and restrained angles, poles offer two clevis lengths and overall lengths
• 12,000 lb max load capacity with a 1" wide clevis for aluminum conductor yoke plates
Cat. No. Description Working Length Weight
H194-9113 Butt Swivel, Clevis 3.35" x 1" 113" 17 lbC400-0612 Butt Swivel, Clevis 1.56" x 1" 113" 14 lbC400-0613 Butt Swivel, Clevis 1.56" x 1" 134" 15 lb
PSC400-2915 Clevis, Clevis 1.56" x 1" 113" 14 lbPSC400-2916 Clevis, Clevis 1.56" x 1" 134" 15 lb
STRAIN POLE ACCESSORIES
Cat. No. Description WeightM1948-3 Ratchet Wrench 2.2 lb
E401-1998P 12" Strain Jack, Tongue Type 3 lbV401-0157P 24" Strain Jack, Tongue Type 4 lbV401-0158 36" Strain Jack, Tongue Type 6 lbH4785-1 12" Clevis Ratchet Screw 5.5 lbH4785-2 18" Strain Jack, Clevis Type 8 lbH4785-3 24" Strain Jack, Clevis Type 10 lb
SPM2-9471 Acme Eyenut 1 lb
Strain JacksTongue Type Strain Jacks
Clevis Type Strain Jacks
M1948-3Ratchet Wrench
C400-0612
H194-9113
C401-1719
C401-1718
C401-1717
174HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com
HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 175
TRANSMISSION TOOLS TRANSMISSION TOOLS
• Used to make insulator changes by supporting the string while damaged insulators are replaced
• Also used to pivot the string so that it may be removed and lowered to the ground
• On deadends or running corners, cradles are used in conjunction with strain carriers
• In straight suspensions, they are used with various link sticks or adjustable strain pole assemblies
Cat. No. Length Capacity WeightH1840-6 6' 10 - 10" Insulators 19.75H1840-8 8' 14 - 10" Insulators 24H1840-10 10' 18 - 10" Insulators 27
Cat. No. Description10" Insulator
CapacityWgtlbs
H1950-9 9' Insulator Cradle 19 23C401-0015 11"-4" Insulator Cradle 25 27H1950-90 Insulator Cradle Carrier --- 25
068922 HOOK
070184 BAIL
H1950-90
• For making insulator changes on lines energized up to and including 500KV
• Also for lowering insulator strings on deadend and swinging corner construction, and to raise the insulators on long suspension units
• Deep trough design holds insulator string securely
STATIC GROUND
Transmission Tools
TRANSMISSION INSULATOR CRADLE
EHV TROUGH-DESIGNINSULATOR CRADLE
Cat. No. Description WeightHG4230-1 with Eyescrew Clamp 5 lbC600-0000 with "T" Handle Clamp 5 lb
• Eliminates electrostatis charge when working insulator strings
• Drains off charge from insulator string to tower leg
• 6' of No. 2 grounding cable is attached• Flat face clamp at one end of grounding cable• Adjustable jaws fit insulator caps 2.5" - 6"
C401-0168
TRANSMISSION TOOLSTr
ansm
issi
on T
ools EHV SIDE OPENING INSULATOR
CRADLE
Cat. No. Description WgtC401-0358 9’ Cradle, 15” Support Hooks 93 lbC401-0359 9’ Cradle, 31” Support Hooks 98 lbC401-0356 13’ Cradle, 15” Support Hooks 119 lbC401-0357 13’ Cradle, 31” Support Hooks 124 lbC401-0354 16’ Cradle, 15” Support Hooks 125 lbC401-0355 16’ Cradle, 31” Support Hooks 131 lbC401-0361 (1) 15” Support Hook 10 lbC401-0362 (1) 31” Support Hook 12 lbC401-0455 Insulator Retaining Plate 8 lb
Cat. No. C402-0790• For removal of deadend insulator strings• Plastisol-covered steel hook swivels on end of
a 2" x 36" Epoxiglas pole• 2.5" diameter pole clamp at the top end• Useful in removing bottom string in a 3
bundle insulator string• Rated working load: 250 lbs per hook
J-HOOK ASSEMBLY
SUSPENSION YOKES
Cat. No. Pole Dia & Lgth WeightH4720-84 1-1/2" x 84" 14 lbH4720-96 1-1/2 x 96" 16 lbH4720-114 1-1/2' x 114" 18 lb
SUSPENSION LINK STICKS
ADJUSTABLE HOOK ASSEMBLYCat. No. M4724-1
• A direct method of relieving load on suspension string
• Conductor clamp has contoured seat with a trapping gripper and is operated by an eyescrew
• Conductor range is 1-1/8" - 2-1/2" dia
• Can be positioned every 6" on the strain pole
• 3,500 lb max load
• For selective removal of any one string in deadend bundles, double, triple or quad
• Eliminates the need for removing top strings in bundle access lower string
• Shipped with bridle for attaching to swivel boom, an insulator retaining plate, and either 15" or 31" hook assemblies
• 500 lb max load for 9' cradle• 1000 lb max load for 13' & 16' cradles
• C401-1722 yoke is used with the H2947 series adjustable strain poles
• C401-0168 yoke is used with clevis strain poles• 15,000 lb max load per insulator string• Has two spring loaded latches which engage and
lock the pole clamp into position on the yoke, 26" apart center to center
Cat. No. Description WgtC401-1722 Strain Pole Yoke - 3.5" Swivel Saddle 26 lbC401-0168 Clevis Pole Yoke - 3.5" Swivel Saddle 23 lb
C401-1722
These sticks are designed for use on conductors from 1" - 2-1/2" dia. and can be used with various types of takeup devices at the structure end. The lip of the hook, actuated by an eye screw, swivels to accommodate various conductor sizes.
Max load: 6,500 lbs.
176HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com
HI-LINE UTILITY SUPPLY CO.Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 177
TRANSMISSION TOOLS TRANSMISSION TOOLSTransm
ission Tools
STRUCTURE YOKES
TOWER HANDLINE GIN
TROLLEY POLE SUSPENSION INSULATOR TOOL
HOT STICK TENSION PULLER
Cat. No. M1979• 3' x 3" x 1/4" with an
aluminum-welded end-plate securing bronze, free-swivel butt ring
• Snatch blocks hooked into butt ring keep handlines from dragging over tower structure
• Hook adjustment will fit tower angle from 1-3/4" x 1-3/4" up to 6" x 6"
• 21" long with a 500 lb max load
Cat. No. DescriptionH4723-2 Fork Suspension Tool Attach. for 2.5" Pole
H472-1112 Trolley Pole (2.5" x 12')H4723-4 Single Trolley Wheel with 2.5" Pole Clamp
C400-0152 Tandem Tolley Wheel with 2.5" Pole Clamp
• Rolls a string of suspension insulators into the structure so that units can be replaced
• Can be fastened horizontally under the tower arm using tower type wire tong saddles
Cat. No. DescriptionC400-0574 34.5KV Hot Stick Tension PullerC400-0575 69KV Hot Stick Tension PullerC400-0600 Tie Back Clamp (#4 - 397.4 kcmil ACSR)C400-0573 Tension Puller Hook Adapter
• Equipped with rings for use with a Grip-All Clampstick or with rubber gloves
• Non-swiveling hook on each end for positive hotstick operation
• Spring loaded gate rotates 135 degrees left or right from closed position
H4723-2H4723-4 C400-0152
Cat. No. H478322• Fits over tower arm,
serving as a support for strain poles
• Yoke legs fit most tower structure configurations
• Max load: 12,000 lb
STEEL TOWER YOKE
Cat. No. C400-0219• Two clamp bolts secure
the yoke to the double plank crossarms and are adjustable to 9", 11", 13"
• Vertical take-up 9"-12"• Max load: 12,000 lb
WOOD OR H-FRAME TOWER YOKE
Cat. No. C400-0445• Use on steel pole arm• Swivel castings in end of
yoke for proper align-ment of strain poles
• Load rating dependent on angle of end plates Max load: 15,000 lb
STEEL ARM YOKE
Cat. No. T400-0838• This bracket is used with
steel arm yoke (above) where the steel arm is not equipped with an end plate.
STEEL ARM BRACKET
Cat. No. LH95This 10" dia. bell lifter is
rubber coated to protect porcelain insulators. 8,000 lb Test Load Wgt: 65 lbs.
Cat. No. PSC400-2927This high-density, 12.6"
dia. bell lifter is made of sturdy polyethylene. 400 lb Test Load Wgt: 13.5 lbs.
PSC400-2927
LH95
INSULATOR LIFTERS