stitch and glue manual

Copyright www.plyboat.com 2013 Page 1

Basic "Stitch-and-Glue" Manual

This manual describes the building of a small boat by the "Stitch-and-Glue" method, also known

as "Taped Seams". The method originated in England in the early 60's and the first boat built was

a Mirror Dinghy designed by Jack Holt. In traditional boatbuilding the builder needs to transfer

from the plans the dimensions of all frames, backbone, stem, stern post and sometimes the entire

boat on the floor full size. This is known as lofting. It's a tedious process requiring a lot of

kneeling and crawling. The chance of making a mistake is higher due to the fact that many

numbers need to be transferred from the paper drawings to the floor. Then using the shapes of

the frames and other hull parts drawn on the floor, the builder has to assemble all of them from

quality marine grade lumber. The cutting and assembly need to be very accurate. Then on all

frames a bevel needs to be made at a certain angle depending on the location of the frame so that

longitudinal members such as stringers and the planking can lay flat on the frame. After that all

frames have to be set up on a level floor, secured with cross beams and braces and only then the

actual planking of the hull can begin. As you can see it's a long and difficult process. In the S&G

method the shape of the boat is defined by the shape of the separate hull panels. They get

stitched together around a small number of frames and then all seams are "welded" with

fibreglass tape and epoxy resin. The hull of the boat takes shape in a matter of a few hours for

smaller boats. No beveling of the frames is needed. Precise fits are not necessary. What counts is

smoothness and fairness. In fact it's better not to have precise fits as they create stress points in

the hull. A little gap is preferred. Epoxy putty made of epoxy resin mixed with filler takes care of

small gaps, holes etc. Then a fillet is applied in the seams of all joining surfaces and fibreglass

tape on top. The fibreglass tape serves as a stringer. Essentially the finished boat is a monoqoque

structure. Here are the major steps of the building procedure for a small flat or v-bottom dinghy.

JOINING PLYWOOD SHEETS

Almost any boat you build from plywood will require panels longer than 8' except some very

small dinghies. There are three popular methods of joining plywood sheets scarfing, butt blocks and fibreglassing. Scarfing is tapering of both sheets in the area of connection in order to

have a bigger contacting surface. The length of the taper can be between 6 and 10 times the

thickness of plywood. Most used is 8 times. For example if you have (6mm) sheets the taper would have to be around 2 (50mm).


I have done scarfing on plywood only once when I was building a 10 (3m) kayak which was going to be left with clear finish. Some builders make a special jig for tapering of the plywood

sheets. When I did the tapering I used a method shown in Devlins book. The two sheets of ply are stacked together and the top sheet is offset from the edge of the bottom sheet with the

amount of taper. Its like a staircase and you have to knock out the stair steps. Draw a guide line on the top sheet same distance from the edge as the offsetting of the two sheets. Then start

planning with a hand or power plane until you get a smooth bevel. Glue both sheets with epoxy

putty and apply pressure by putting weights on the joint. Place a piece of plastic before you put

the weights on to make sure nothing sticks to the plywood because there will be some epoxy

putty coming out. Also make sure both sheets dont slide away and the long edges are straight. Give it at least two days to cure. Then sand it smooth.

To spread the pressure more uniformly use a piece of scrap wood over the joint and then place

the weights on top. Check alignment of both sheets before walking away.


Butt blocks are simply a piece of plywood same thickness as the joining sheets about 8-10 wide (200-250mm) glued on one side connecting both sheets. Usually designers who specify butt

blocks in their designs try to position them in places where they will be less visible or completely

hidden, for example under a frame or inside a seat which is also emergency flotation or storage

compartment. I have built two boats using butt blocks and its one of my favorite methods. The joint is stronger than the strength of the connected pieces. Its easy and fast to make leaving no room for errors. One thing about butt blocks is they need to be shorter than the connected pieces

to allow room where the fibreglass tape will be passing.

There should be about 2 (50mm) gap from butt block to the edge of the panel. This is done to make room for the fibreglass tape.

The third method is fibreglass joint. Its like a butt block but made of fibreglass and it has to be applied on both sides. The problem here is that the builder has no control over the proper

saturation of the fibreglass butt block which is underneath. The best that can be done is to wet

out thoroughly the fibreglass and the plywood in the joining area. The top fibreglass butt block

can be wetted out properly then plastic and weights are placed. The weights will also flatten the

joint to the point where very little sanding will be required after epoxy is cured. I have used this

type of joint on a 9 (2.80m) fishing kayak which I designed not long ago. I placed the joint in the rear compartment and its basically invisible. The outside is faired and no one can tell there is


a joint. The advantage of the fibreglass method over the butt block method is that fibreglass

somehow better conforms to curves whereas the butt blocks tend to create sort of a bump or hard

spot. But again if properly placed in the boat both methods are very good and reliable.

More epoxy putty should have been added to the joint to fill the gaps between the two panels.


LOFTING

Lofting is the process of transferring the dimensions of frames and panels from drawing to

plywood. In many plans the designers use the long edge of the plywood sheet as a baseline from

which to measure the distances. Its very convenient and accurate. Also some sort of grid on the plywood sheet is very helpful to transfer points. Usually it is made by drawing vertical lines 12 (305mm) apart using the short edge of the plywood. It is like a coordinate system with the long

plywood edge being the X ordinate and the short plywood edge the Y ordinate. Here is how to

draw the vertical lines 12 (305mm) apart. If we have a second sheet of plywood (and we usually do as even the smallest boats require at least two sheets of ply) just slide it on top of the sheet on

which the drawing will be done and align the long edges of both sheets. Then by carefully

offsetting (moving) the top sheet to the right draw the vertical lines of the grid 12 (305mm) apart. We use the natural straight edge of the plywood sheet! Of course a drywall square can be

used too.

Start marking the points along the lines of the grid. Curved lines require more points to define

their shape. Straight lines need just two points. When all the points are marked double check for

any errors. Then hammer a small nail at each marked point and bend a batten (flexible molding

or PVC pipe) around the nails. Keep it in place with some sort of weight a thick book, milk containers filled with water, rocks, etc. Draw the line with pencil. In some boats you will have

straight lines. Then just use the long edge of the second sheet of ply and draw the line between

two points. The location of the frames must be marked on the side panels. Dont forget to draw these lines too. They are important!


Apply pressure to the batten to get a smooth and fair curve.

As boats are symmetrical they have two side panels and two bottom panels (in the v-bottom

hulls). Once you draw one of the panels on the plywood, cut it out and flip it over as a mirror

image. Use it as a template and draw the second panel. Transfer the location of frames from the

first panel to the second. Now you can cut out the second panel too. For cutting of long straight

and curved lines I use a circular saw with the blade set just to clear the thickness of the plywood.

Sometimes for smaller boats I use a hand saw. Its a good exercise and the cuts are very straight. For small radius curves such as on the frames or support knees it is best to use a jigsaw. So now

we have both side panels of our small dinghy cut out. If you havent cut the frames yet now is a good time. Just transfer the dimensions from the plans, connect the points (usually straight lines)

and cut them out. In some designs (for example our 7.5 dinghy Colibri) the frames are assembled from dimensional lumber. In our designs the thickness of the planking is already

deducted. Some designers give the dimensions to the outside of the planking in which case the

builder has to deduct it when drawing the frames. Now we have all the major hull components

cut out so we are ready to start stitching up the boat.


STITCHING UP THE BOAT

Align the middle frame with the marks on the side panels. Attach both side panels using drywall

screws. Two screws on each side are enough. Dont drive them all the way down. If you are building a flat bottom boat work right side up. If building a v-bottom boat, do it upside down.

Then attach the bows of the two side panels with copper wire. Usually three stitches equally

spaced are enough for the bow. Drill the holes for the stitches about 3/8 (10mm) from the edge of the plywood. Dont tighten them too much. Just snug by hand is enough. Attach the transom. Use stitches or drywall screws. For stitching use 16 or 18 gauge copper or aluminum wires cut in

pieces of about 6 (150mm) long.

Note the two temporary spreaders. Once the boat is welded with fibreglass tape in epoxy and

the rubrail is installed the spreaders can be removed.


If building a flat bottom boat slide the other sheet of plywood underneath the assembly weve done so far. By rocking it gently back and forth outline the shape of the bottom panel. Cut it out

and drill holes for the stitches about 3/8 (10mm) from the edge of the plywood every 4 (100mm). Transfer the position of the holes from the bottom panel to where the holes on the side

panels will be. Drill those holes. Stitch the bottom panel to the side panels by doing two stitches

on one side, two on the other. This way we minimize the chance of ending up with a twisted

boat. When done with the stitching measure the diagonals from the corners of the transom to the

bow. Both readings should be same within (6mm). If everything is OK tighten all stitches. If you are building a v-bottomed boat the bottom will be made of two panels. The best way is to

stitch both panels as they are stacked on top of each other along the keel line. This way you can

drill the holes for the stitches simultaneously through both panels. Wire them up but dont tighten the stitches too much. Now open the panels like a book and place them on top of the

assembly we did earlier. Thats why we did it upside down for the v-bottom hull. When the entire hull is stitched up turn it over in normal position. You may have to place some sort of

support under the chines to keep it more or less level. Measure the diagonal in the same way we

did for the flat bottom boat. If everything is OK tighten all stitches.

Its very important to measure the diagonals before welding the panels with epoxy putty. If there is any twist in the hull it will get locked in by the epoxy and you will end up with a

twisted boat.


TAPED SEAMS

There are now two ways to continue the building process. One is to make temporary small fillets

(tabs) between the stitches with a mixture of epoxy resin and wood flour. This mixture is called

epoxy putty. It has the consistency of peanut butter. Then pull the wires out and apply a long

continuous fillet of epoxy putty.

The hull is spot welded ready for the filleting and fibreglass tape.

The other way is to flatten as much as possible the wire stitches from inside so they lay closer to

the plywood. This is easily done with a flat screw driver. Just press lightly on the wire until its bent towards the seam. Then a long and continuous fillet is applied in the seam between the two

panels and the wires are buried underneath. You can do it either way. Its your choice. I prefer to leave the wires inside and then cut them out on the outside as close as possible to the plywood.

Some people are pulling them out by applying heat to the wires to soften locally the epoxy fillet

holding it. I was never consistent in doing that. Anyway, even if part of the wire is left inside its not a big deal. Copper doesnt rust even if moisture somehow creeps into the joint through the fibreglass which happens very rarely. The best applicator Ive found for applying epoxy putty inside the seams is the pastry bag method. Its a plastic bag (ziplock or similar) in which you put the epoxy putty cut one corner with a scissor and squeeze it. The fillets become very uniform

and clean. After the fillet is applied use a rounded plastic squeegee or a tongue depressor to


shape it nicely so the fibreglass tape can lay on top. Wait about an hour or two before applying

the fibreglass tape to the fresh fillet so it can harden a bit to keep its shape when the tape is applied on top. But dont wait for the fillet to harden completely. Then youll have to do a lot of sanding and even then there will be air bubbles left under the fibreglass. So always work wet-on-

wet! Saves a lot of sanding, time and the quality of the job is superior.

Pastry bag ready for application.


Note the continuous fillet. Soon (in 1 - 2 hours) fibreglass tape will be applied on top.

Rounded plastic squeegee for filleting.


Short pieces of 3 (75mm) wide tape are precut for the front and rear compartments. The key to successful fibreglass job is preparation. When your hands are all sticky with epoxy which is

kicking-in (hardening), its hard to measure and cut tape properly.

Make sure the tape covers equal portions of each panel. Dont push too hard. Fillet is still soft.


It helps to have the fibreglass tape precut for the separate sections of the boat. For example cut

short strips for the buoyancy chambers and the central cockpit area. If this is your first project

start with areas which will remain hidden under seats or inside buoyancy chambers. By the time

you get to the open visible areas you will be doing a professional looking tape job.

When you are done with the taping of the inside of the boat and the epoxy is hardened you can

turn the boat upside down, cut all wires as deep as possible and round all outside edges so the

fibreglass tape can lay on top without leaving air bubbles underneath. Fill any gaps with epoxy

putty and make everything round and smooth. Brush some unthickened epoxy (epoxy without

filler) in the area of the seams and place the precut strips of tape. Wet it out thoroughly until it

becomes transparent. Wait for at least 24 hours until everything is properly cured.

Fill any gaps with epoxy putty and make everything round and smooth. Fiberglass tape likes

round edges and smooth surfaces.


Dry fitting the lengths of tape.

Properly saturated tape becomes transparent. If any air gaps underneath cut with knife and

apply more epoxy. Note how it covers the holes (which were filled with putty) from the stitches.


SANDING AND FAIRING

Now we have our little boat all taped up inside and out. If you havent coated all surfaces with unthickened epoxy now is a good time. After all epoxy work is cured its time for sanding. I do the sanding with 60 grit sandpaper. It may seem rough for some people but I found that the

higher grits actually get clogged very quickly. I use a sanding block and a rubber disc for the

drill on which sandpaper is attached. First try to knock down the binder tread of the fibreglass

tape until it tapers down to the plywood. Then lightly sand the entire boat. Keep an eye for any

drips which are now hardened and remove them. Then wipe everything with alcohol or warm

water mixed with some vinegar. Next comes the application of fairing compound. You can

purchase a ready made one or you can make your own simply by mixing fine glass bubbles or

phenolic microbaloons in the epoxy until you reach the consistency of peanut butter. Glass

bubbles and phenolic microbaloons create a very fine fairing compound which is also very easy

to sand. A good indicator for the right consistency would be when you lift the mixing stick and

the mixture is not flowing down. Same as when you mix wood flour for the fillets. The fairing

compound can be applied directly with the mixing stick in small portions along the seams. Then

using a wide squeegee spread it nicely and uniformly along the seams. The gap between the

fibreglass tape edge and the plywood will be filled and the texture of the fibreglass tape too. Try

not to apply too much fairing mixture. Just enough to fill the low spots. You may have to do a

second run later on if you are not happy with the result. After the fairing is cured sand it with 60

grit sandpaper. Wipe again and apply final coat of unthickened epoxy. This last step thoroughly

and uniformly seals everything, provides additional moisture-proofing and creates smooth stable

base for the paint.


Now we can install the skeg (fin) on the bottom. It provides lateral resistance and helps the boat

keep good tracking. First cut a cardboard pattern tracing as close as possible the shape of the

bottom. Then cut the skeg from plywood or any available lumber with thickness between and (12 to 20mm). Spot weld it in place holding it temporary with some masking tape or any other support. Make sure it is straight. Once the spot welds are cured you can apply a continuous fillet the same way we did for the fillets inside the boat. If you want the skeg to be

strong and rigid place some fibreglass tape too.

Note how while fairing the boat, the skeg was installed with small tabs of fairing compound.

This way you save materials and time. Instead of mixing small portions of epoxy try to plan

ahead and always have something extra for glueing. Otherwise you have to throw away

expensive epoxy.


INSTALLATION OF APPENDAGES

Turn the boat over to normal position . Place all additional frames according to the plans. Then

some cleats will have to be glued to hold the seat tops. Install any hatches, inspection ports, drain

plugs, etc. Now is a good time. Later on you will have limited access. Before you glue the decks

or seat tops over the buoyancy compartments apply a final coat of unthickened epoxy inside.

Front deck is held in place with masking tape until epoxy putty cures. Then a nice and clean

fillet is applied in the seam, sanded and faired. Check for drips inside and clean while you

can.


A support knee is installed held in place with masking tape until epoxy tabs cure. Then fillet

and small pieces of fibreglass will make it as strong as it can be. The hole will be used as

anchor point for the seat backrest.

Cleats to support the seat. Note how pressure is applied to the cleats on the side panels.


The next step would be installation of rubrail, breasthook and transom knees. These elements

provide additional strength. The rubrail stiffens the sheer and also provides protection when the

boat is tied to a pier, hence the name rubrail. It can be made of a single piece of around 1 3/8 by (35x20mm) or laminated of thinner pieces. Either way, first clamp the stock in the middle of the sheer and slowly progress towards the ends using c-clamps or spring clamps. When the

rubrail is cured remove the clamps and shape it nicely with a plane or a rasp. Sand it and fill any

gaps with epoxy putty. Now you can take the shape for the breasthook and transom knees with

cardboard patterns. Cut them out of plywood or any available stock wood. The shape is not

critical. When installing them apply a fillet of epoxy putty underneath and also some fibreglass

tape for reinforcement. Very often you will be using the knees as handles to transport the boat.

So they need to be strong.

Installation of rubrail with only two clamps in the middle. The holes from the zip ties will have

to be filled though.


Cockpit coaming made of half round molding. Installed with c-clams, spring clamps and wire

stitches.

Rubrail, transom and bow knees are installed. Seat, oarlock socket pads and transom

reinforcement are getting glued. Note the gap between the seat and side panel. Later will be

filled with epoxy putty.


FINISHING AND PAINTING

Before applying the first coat of primer you will have to sand the boat one more time. Then wash

it with soapy water and rinse thoroughly. Then dry the surface with clean rags. This is done to

get rid of a thin greasy film which is a by-product of the reaction of epoxy curing with air. It has

to be removed so the primer can get a good bond.

Prime the boat with two coats. Sand with 220 grit sandpaper to create a tooth for the paint. Then

apply 3 to 5 coats of paint depending on the color. Use a roller and brush. I paint my boats with

ordinary exterior house (porch) paint. Nothing fancy, expensive and poisonous. Most small boats

spend not more than 3-4 hours per week in the water in the summer months so there is no need

for expensive marine grade paint. Sometimes I use a pigment which is added into the epoxy to

create a nice decorative mahogany finish on some details such as rubrail, cockpit coaming, seats,

support knees, etc. Of course wood stain can be used too. Just make sure it is water based

otherwise the epoxy wont be able to adhere properly to it. Thats it! Your boat is ready for adventures! Enjoy it and be safe! If you have any questions please e-mail to: [email protected]

stitch and glue manual

Documents

small boat

plywood sheets

entire boat

finished boat

small number of frames

sheets of ply

thickness of plywood

glue method