startup guide for kvm on cent os 6

Techno Crazy

Simplifying Server Aidministration

Home

About

Home > Uncategorized > Startup Guide for KVM on CentOS 6

Startup Guide for KVM on CentOS 6

August 29, 2011 balrawat Leave a comment Go to comments

These instructions are very specific to CentOS 6.

For this I assume you have setup your server using the “Minimal” option when installing CentOS 6. You

must also have the Virtualization features enabled for your CPU. This is done in your host’s BIOS.

Optionally you can skip the first section, Installing KVM, if you check all 4 “Virtualization” software

categories during the install.

Installing KVM

If you choose the “Minimal” option during CentOS 6 then this step is necessary. To get the full set of tools

there are 4 software groups to install…

Virtualization

Virtualization Client

Virtualization Platform

Virtualization Tools

To install run

yum groupinstall “Virtualization*”

dejavu-lgc-sans-fonts is necessary or all the fonts in virt-manager will show as squares

yum install dejavu-lgc-sans-fonts

Once the install is finished verify that the KVM kernel module is loaded.

lsmod | grep kvm

You should see either kvm_intel or kvm_amd depending on your host’s CPU manufacturer.

At this point I chose to reboot the server. This allows services to be started and udev rules for KVM to be

applied. This will also allow dbus to create the machine-id file, otherwise you would see something like

the below when running virt-manager

# virt-manager

Xlib: extension “RANDR” missing on display “localhost:10.0″.

process 1869: D-Bus library appears to be incorrectly set up; failed to read machine uuid: Failed to

open “/var/lib/dbus/machine-id”: No such file or directory

See the manual page for dbus-uuidgen to correct this issue.

D-Bus not built with -rdynamic so unable to print a backtrace

Startup Guide for KVM on CentOS 6 « Techno Crazy http://balvinder.wordpress.com/2011/08/29/startup-guide-for-kvm-on-c...

1 de 5 17/11/2011 09:49

Aborted

If you receive that D-Bus error and would prefer not to restart then run this command to generate the

necessary machine-id file

dbus-uuidgen > /var/lib/dbus/machine-id

Final configuration steps

The server I run KVM on is headless, but I still like using virt-manager. So we must install the necessary

tools to do X11 forwarding through SSH.

yum install xorg-x11-xauth

# If you plan to use VNC to connect to the virtual machine’s console locally

yum install tigervnc

Now when you connect through SSH be sure to pass the -X flag to enable X11 forwarding.

Optional: Using an alternate location for VM images with SELinux

With SELinux enabled, special steps must be taken to change the default VM store from /var/lib/libvirt

/images. My particular server I choose to keep all images and ISOs for VMs under /vmstore. The steps

below give your new store the correct security context for SELinux.

# this package is necessary to run semanage

yum install policycoreutils-python

semanage fcontext -a -t virt_image_t “/vmstore(/.*)?”

restorecon -R /vmstore

To activate this store you must open virt-manager, select your host, then do Edit-> Host Details. Under the

Storage tab you can add your new storage volume.

Optional : Network Bridging for Virtual Machines

If you wish for your virtual machines to be accessible remotely then you must use network bridging to

share your host’s network interface with the virtual machines. The setup requires linking one of your

host’s physical interfaces with a bridge device. First copy your physical interface’s ifcfg file to create the

new bridge device, named br0.

cp /etc/sysconfig/networking-scripts/ifcfg-eth0 /etc/sysconfig/networking-scripts/ifcfg-br0

Modify ifcfg-br0 to have the IP information in ifcfg-eth0 and remove, or comment out, that information in

ifcfg-eth0. Below are examples of ifcfg-eth0 and ifcfg-br0. The highlighted lines are important.

/etc/sysconfig/networking-scripts/ifcfg-eth0

DEVICE=eth0

HWADDR=00:18:8B:58:07:3B

ONBOOT=yes

BRIDGE=br0

/etc/sysconfig/networking-scripts/ifcfg-br0

DEVICE=br0

TYPE=Bridge

BOOTPROTO=static

ONBOOT=yes

IPADDR=10.1.0.3

NETMASK=255.255.255.0

Once those two files are configured restart the network service

service network restart


2 de 5 17/11/2011 09:49

Share this:

Optional: Managing libvirt with standard user account

Beginning in CentOS 6 access to managing libvirt is handled by [http://wiki.libvirt.org

/page/SSHPolicyKitSetup PolicyKit]. It’s always a good practice to do your daily administration tasks as

some user besides root, and using PolicyKit you can give access to libvirt functions to a standard account.

First we create the necessary config file to define the access controls. The file must begin with a numeric

value and have the .pkla extension.

vim /etc/polkit-1/localauthority/50-local.d/50-libvirt-remote-access.pkla

Here’s an example of the file I used to give access to a single user. Be sure to put your desired username

in place of username on the highlighted line.

[libvirt Management Access]

Identity=unix-user:username

Action=org.libvirt.unix.manage

ResultAny=yes

ResultInactive=yes

ResultActive=yes

You can optionally replace Identity=unix-user:username with Identity=unix-group:groupname to allow

access to a group of users.

Finally restart the libvirtd daemon to apply your changes.

/etc/init.d/libvirtd restart

Creating the first virtual machine

You are now ready to create your virtual machines.

Create the virtual disk

With the version of virt-manager shipped with CentOS 6 you cannot create qcow2 images from within the

GUI. If you wish to create your new VM with a qcow2 format virtual disk you must do so from the

command line, or see the next section for RPMs to upgrade virt-manager.

qemu-img create -f qcow2 CentOS-6.0-x86_64-Template.qcow2 20G

NOTE: Replace the filename “CentOS-6.0-x86_64-Template” with your desired name, and also replace

“20G” with the desired max size of the virtual disk.

Now when creating your virtual machine select to use an existing virtual disk.


3 de 5 17/11/2011 09:49

Like this:Be the first to like this post.

Fill in your details below or click an icon to log in:

Notify me of follow-up comments via email. Post Comment

Categories: Uncategorized

Comments (0) Trackbacks (0) Leave a comment Trackback

No comments yet.1.

No trackbacks yet.1.

Leave a Reply

SQL Server point in time recovery Crazy Commands

RSS feed

Google

Youdao

Xian Guo

Zhua Xia

My Yahoo!

newsgator

Bloglines

iNezha

Calendar

August 2011

M T W T F S S

« May Sep »

1 2 3 4 5 6 7

8 9 10 11 12 13 14


4 de 5 17/11/2011 09:49

M T W T F S S

« May Sep »

15 16 17 18 19 20 21

22 23 24 25 26 27 28

29 30 31

Archives

September 2011 (1)

August 2011 (1)

May 2011 (1)

April 2011 (1)

March 2011 (4)

Recent Posts

SQL Server point in time recovery

Startup Guide for KVM on CentOS 6

Crazy Commands

How to install NTOP on CentOS 5.5 64bits

How to Block the Amazon AWS EC2 crawlers

Email Subscription

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1 other follower

Top WordPress

Copyright © 2009-2011 Techno Crazy

Blog at WordPress.com. Theme: INove by NeoEase.


5 de 5 17/11/2011 09:49

startup guide for kvm on cent os 6

Technology