standard model lineup model and type designation gtr-l · pdf filegtr-l series g type parallel...
TRANSCRIPT
■Gearmotor/Gearmotor with Brake/Reversible Gearmotor
Model and Type Designation/Standard Model Lineup
3-phase Performance Table/Dimension Diagram
1-phase Performance Table/Dimension Diagram
■Speed Control Gearmotor/Speed Control Gearmotor with Brake
Model and Type Designation/Standard Model Lineup
1-phase Performance Table/Dimension Diagram
P.
P.
P.
P.
P.
D5
D9
D19
D33
D37
D1
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
Model and Type DesignationStandard Model Lineup
GTR-L SeriesGearmotor
Parallel Shaft
D3D2
①Classification by Mount Form
②Series Name
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
L
F
G
Blank
N
R
U
P
PN
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
T15
T25
T40
S06
S10
S15
S25
S40
Blank
W
T
K
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Brake Motor
: Reversible(1-phase only)
: With Speed Control Gearmotor
: With Speed Control Gearmotor
: With Speed control brake motors
: Metal type
: Bearing type
: 3-phase 15W
: 3-phase 25W
: 3-phase 40W
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: T-Type Terminal Box
: K-Type Terminal Box
: Rectifier built-in terminal box for brake motor
: Terminal box for Speed Control type motor
: Standard Specs.
: Mark for Additional Specs.
U-Type(With Controller)
P-Type(Controller Sells Separately)
P-Type(Controller Sells Separately)
3-phase: 1-phase:
200V/50Hz、200V/60Hz、220V/60Hz 100V/50Hz、100V/60Hz
3-phase: 1-phase:
380V/50Hz、400V/50Hz、400V/60Hz、440V/60Hz 200V/50Hz、200V/60Hz(except for 6W)
L Series(Parallel Shaft) Model and Type Designation
GTR-L Series gearmotors are classified by codes as shown below. Specify these codes in your inquiry and order.
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
③Classification by Motor Type
⑪Spec. DesignationNote: Spec. Designation does not appear on
the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Note 1: Note 2:
For the types stated below, manufacturing with double voltage is not feasible. ●Single-phase 6W Be sure that the specification of C-Type Terminal Box for brake motors with rectifier built-in is different from that for the speed control type. For more details, refer to P. E40 and P. E56
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
LG 15 240 T25F W
MMN
G 15 360 S40F BNC X T6
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
GTR-L Series
D3D2
①Classification by Mount Form
②Series Name
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
L
F
G
Blank
N
R
U
P
PN
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
T15
T25
T40
S06
S10
S15
S25
S40
Blank
W
T
K
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Brake Motor
: Reversible(1-phase only)
: With Speed Control Gearmotor
: With Speed Control Gearmotor
: With Speed control brake motors
: Metal type
: Bearing type
: 3-phase 15W
: 3-phase 25W
: 3-phase 40W
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: T-Type Terminal Box
: K-Type Terminal Box
: Rectifier built-in terminal box for brake motor
: Terminal box for Speed Control type motor
: Standard Specs.
: Mark for Additional Specs.
U-Type(With Controller)
P-Type(Controller Sells Separately)
P-Type(Controller Sells Separately)
3-phase: 1-phase:
200V/50Hz、200V/60Hz、220V/60Hz 100V/50Hz、100V/60Hz
3-phase: 1-phase:
380V/50Hz、400V/50Hz、400V/60Hz、440V/60Hz 200V/50Hz、200V/60Hz(except for 6W)
L Series(Parallel Shaft) Model and Type Designation
GTR-L Series gearmotors are classified by codes as shown below. Specify these codes in your inquiry and order.
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
③Classification by Motor Type
⑪Spec. DesignationNote: Spec. Designation does not appear on
the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Note 1: Note 2:
For the types stated below, manufacturing with double voltage is not feasible. ●Single-phase 6W Be sure that the specification of C-Type Terminal Box for brake motors with rectifier built-in is different from that for the speed control type. For more details, refer to P. E40 and P. E56
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
LG 15 240 T25F W
MMN
G 15 360 S40F BNC X T6
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
GTR-L Series
D4
GTR - LSe r i e s
GType
Parallel Shaft
D5
3-Phase
15W~40W
3 Rated Power Source 200V 50/60Hz, 220V/60Hz
Class E
Direct start
Totally Enclosed
4
Continuous Rating
Spur gear and Helical gear
Grease Lubrication
New JIS Key(JIS 1301-1976 class)
S43C
Aluminium die-cast
-10℃~40℃
85% max.(without any dew condensation)
1,000m max.
Indoors
Anion painting, Acrylic paint
Grey(Mansel code: 9B6/0.5)
No restriction in the mounting angle.(horizontally, vertically or heeling angle)
6W~40W
100V 50/60Hz
Class E
Capacitor Start
1-Phase
Well ventilated place free from corrosive gas, explosive gas vapor and/or dust.
Motor Part
Ambient Conditions
Painting
Mounting Direction
Speed Reduction Part
Number of phase
Capacity
Power Source
Starting Method
Number of Pole
Rating
Reduction Method
Lubrication
Output Shaft
Case Material
Ambient Humidity
Altitude
Painting Method
Painting Color
Insulation Classification
Protective cooling Method
Output Shaft Material
Ambient Temperature
Installation Location
Environment
Gearmotor
Model and Type DesignationStandard Model Lineup
GearmotorGearmotor with BrakeReversible gearmotor
Parallel Shaft
(1-Phase only)
D4
GTR - LSe r i e s
GType
Parallel Shaft
D5
3-Phase
15W~40W
3 Rated Power Source 200V 50/60Hz, 220V/60Hz
Class E
Direct start
Totally Enclosed
4
Continuous Rating
Spur gear and Helical gear
Grease Lubrication
New JIS Key(JIS 1301-1976 class)
S43C
Aluminium die-cast
-10℃~40℃
85% max.(without any dew condensation)
1,000m max.
Indoors
Anion painting, Acrylic paint
Grey(Mansel code: 9B6/0.5)
No restriction in the mounting angle.(horizontally, vertically or heeling angle)
6W~40W
100V 50/60Hz
Class E
Capacitor Start
1-Phase
Well ventilated place free from corrosive gas, explosive gas vapor and/or dust.
Motor Part
Ambient Conditions
Painting
Mounting Direction
Speed Reduction Part
Number of phase
Capacity
Power Source
Starting Method
Number of Pole
Rating
Reduction Method
Lubrication
Output Shaft
Case Material
Ambient Humidity
Altitude
Painting Method
Painting Color
Insulation Classification
Protective cooling Method
Output Shaft Material
Ambient Temperature
Installation Location
Environment
Gearmotor
Model and Type DesignationStandard Model Lineup
GearmotorGearmotor with BrakeReversible gearmotor
Parallel Shaft
(1-Phase only)
D7D6
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200101-Phase 6W
LGN FGN
LG FG
LGR FGR
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200101-Phase 10W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36012
3-Phase 15W
1-Phase 15W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36015
3-Phase 40W
1-Phase 40W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120
1/160 1/200 1/240 1/300 1/360
12
15
3-Phase 25W
1-Phase 25W
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
L
③Classification by Motor Type
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
⑪Spec. Designation
L
F
G
Blank
N
R
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
T15
T25
T40
S06
S10
S15
S25
S40
Blank
W
T
K
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Brake Motor
: Reversible(1-phase only)
: Metal type
: Bearing type
: 3-phase 15W
: 3-phase 25W
: 3-phase 40W
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: T-Type Terminal Box
: K-Type Terminal Box
: Rectifier built-in terminal box for brake motor
: Standard Specs.
: Mark for Additional Specs.
G 15 240 T25F W
3-phase: 1-phase:
200V/50Hz、200V/60Hz、220V/60Hz 100V/50Hz、100V/60Hz
3-phase: 1-phase:
380V/50Hz、400V/50Hz、400V/60Hz、440V/60Hz 200V/50Hz、200V/60Hz(except for 6W) 1-ph 6W type is not available for
high voltage.
MM
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
NG 15 360 S40F BR
C X T6
(Note 1)
L Series(Parallel Shaft) Model and Type Designation Standard Model Lineup
GTR-L Series Gearmotor/Brake Motor/Reversible Gearmotor are classified by codes as shown below. Specify these codes in your inquiry and order.
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
Note:
Note:
Spec. Designation does not appear on the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Foot Mount type Flange Mount type
Reversible motors are available only in single-phase. The models enclosed with orange color bold line are low torque type. Special care should be given to the allowable torque in the performance table.
Note 1) 2)
Type Frame Number Reduction Ratio4P Motor
Capacity
Gearmotor
Gearmotor with Brake
Reversible Gearmotor
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
GTR-L Series
①Classification by Mount Form
②Series Name
D7D6
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200101-Phase 6W
LGN FGN
LG FG
LGR FGR
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200101-Phase 10W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36012
3-Phase 15W
1-Phase 15W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36015
3-Phase 40W
1-Phase 40W
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120
1/160 1/200 1/240 1/300 1/360
12
15
3-Phase 25W
1-Phase 25W
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
L
③Classification by Motor Type
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
⑪Spec. Designation
L
F
G
Blank
N
R
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
T15
T25
T40
S06
S10
S15
S25
S40
Blank
W
T
K
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Brake Motor
: Reversible(1-phase only)
: Metal type
: Bearing type
: 3-phase 15W
: 3-phase 25W
: 3-phase 40W
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: T-Type Terminal Box
: K-Type Terminal Box
: Rectifier built-in terminal box for brake motor
: Standard Specs.
: Mark for Additional Specs.
G 15 240 T25F W
3-phase: 1-phase:
200V/50Hz、200V/60Hz、220V/60Hz 100V/50Hz、100V/60Hz
3-phase: 1-phase:
380V/50Hz、400V/50Hz、400V/60Hz、440V/60Hz 200V/50Hz、200V/60Hz(except for 6W) 1-ph 6W type is not available for
high voltage.
MM
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
NG 15 360 S40F BR
C X T6
(Note 1)
L Series(Parallel Shaft) Model and Type Designation Standard Model Lineup
GTR-L Series Gearmotor/Brake Motor/Reversible Gearmotor are classified by codes as shown below. Specify these codes in your inquiry and order.
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
Note:
Note:
Spec. Designation does not appear on the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Foot Mount type Flange Mount type
Reversible motors are available only in single-phase. The models enclosed with orange color bold line are low torque type. Special care should be given to the allowable torque in the performance table.
Note 1) 2)
Type Frame Number Reduction Ratio4P Motor
Capacity
Gearmotor
Gearmotor with Brake
Reversible Gearmotor
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
GTR-L Series
①Classification by Mount Form
②Series Name
D8 D9
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
Performance TableDimension diagram
Parallel Shaft
GearmotorGearmotor with Brake
●
●
3-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
D8 D9
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
Performance TableDimension diagram
Parallel Shaft
GearmotorGearmotor with Brake
●
●
3-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
D11D10
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
LG FG LGN FGN
3-phase 15W
12
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
P.D11 Fig.D-1 2kg
P.D11 Fig.D-2 2kg
P.D11 Fig.D-3 2kg
P.D11 Fig.D-4 2kg
50Hz 60Hz
LG-12 -3~360-T15LG-12 -3~360-T15WFig.D-1
〔Round Weight 2kg〕 LG-12M-T15 LG-12M-T15W
FG-12 -3~360-T15FG-12 -3~360-T15WFig.D-2
〔Round Weight 2kg〕 FG-12M-T15 FG-12M-T15W
LGN-12 -3~360-T15LGN-12 -3~360-T15WFig.D-3
〔Round Weight 2kg〕 LGN-12M-T15 LGN-12M-T15W
FGN-12 -3~360-T15FGN-12 -3~360-T15WFig.D-4
〔Round Weight 2kg〕 FGN-12M-T15 FGN-12M-T15W
*
*
15W
12
12
T15
T15W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.14/0.13/0.13
0.11/0.12/0.10/0.11
1350/1550/1600
1400/1400/1700/1700
E
N・m kgf・m N kgf
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
Foot Mount type Flange Mount type
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
G-Type〔Parallel Shaft〕 3-Phase 15W
GearmotorGearmotor with Brake
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Gearmotor Flange Mounted Type Gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D11D10
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
LG FG LGN FGN
3-phase 15W
12
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
P.D11 Fig.D-1 2kg
P.D11 Fig.D-2 2kg
P.D11 Fig.D-3 2kg
P.D11 Fig.D-4 2kg
50Hz 60Hz
LG-12 -3~360-T15LG-12 -3~360-T15WFig.D-1
〔Round Weight 2kg〕 LG-12M-T15 LG-12M-T15W
FG-12 -3~360-T15FG-12 -3~360-T15WFig.D-2
〔Round Weight 2kg〕 FG-12M-T15 FG-12M-T15W
LGN-12 -3~360-T15LGN-12 -3~360-T15WFig.D-3
〔Round Weight 2kg〕 LGN-12M-T15 LGN-12M-T15W
FGN-12 -3~360-T15FGN-12 -3~360-T15WFig.D-4
〔Round Weight 2kg〕 FGN-12M-T15 FGN-12M-T15W
*
*
15W
12
12
T15
T15W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.14/0.13/0.13
0.11/0.12/0.10/0.11
1350/1550/1600
1400/1400/1700/1700
E
N・m kgf・m N kgf
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
Foot Mount type Flange Mount type
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
G-Type〔Parallel Shaft〕 3-Phase 15W
GearmotorGearmotor with Brake
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Gearmotor Flange Mount Type Gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D13D12
Foot Mount Type Gearmotor
Flange Mounted Type Gearmotor
LG-12 -3~120-T25LG-12 -3~120-T25WFig.D-5
〔Round Weight 2kg〕
LG-15 -160~360-T25LG-15 -160~360-T25WFig.D-6
〔Round Weight 2.5kg〕 LG-12M-T25 LG-12M-T25W
LG-15M-T25 LG-15M-T25W
FG-12 -3~120-T25FG-12 -3~120-T25WFig.D-7
〔Round Weight 2kg〕
FG-15 -160~360-T25FG-15 -160~360-T25WFig.D-8
〔Round Weight 2.5kg〕 FG-12M-T25 FG-12M-T25W
FG-15M-T25 FG-15M-T25W
LG FG LGN FGN
3-phase 25W
12
15
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
2.7
2.7
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
26.5
26.5
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
P.D13 Fig.D-5 2kg
P.D13 Fig.D-7 2kg
P.D14 Fig.D-9 2.5kg
P.D14 Fig.D-11 2.5kg
P.D13 Fig.D-6 2.5kg
P.D13 Fig.D-8 2.5kg
P.D14 Fig.D-10 3kg
P.D14 Fig.D-12 3kg
50Hz 60Hz
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
25W
12
15
12
15
T25
T25W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.21/0.19/0.19
0.18/0.17/0.17
0.11/0.12/0.11/0.12
0.09/0.09/0.09/0.09
1350/1550/1600
1350/1550/1600
1350/1400/1600/1650
1300/1350/1550/1600
E
N・m kgf・m N kgf
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 3-Phase 25W
GearmotorGearmotor with Brake
G-Type〔Parallel Shaft〕 3-Phase 25WGearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series GTR-L Series
D13D12
Foot Mount Type Gearmotor
Flange Mount Type Gearmotor
LG-12 -3~120-T25LG-12 -3~120-T25WFig.D-5
〔Round Weight 2kg〕
LG-15 -160~360-T25LG-15 -160~360-T25WFig.D-6
〔Round Weight 2.5kg〕 LG-12M-T25 LG-12M-T25W
LG-15M-T25 LG-15M-T25W
FG-12 -3~120-T25FG-12 -3~120-T25WFig.D-7
〔Round Weight 2kg〕
FG-15 -160~360-T25FG-15 -160~360-T25WFig.D-8
〔Round Weight 2.5kg〕 FG-12M-T25 FG-12M-T25W
FG-15M-T25 FG-15M-T25W
LG FG LGN FGN
3-phase 25W
12
15
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
2.7
2.7
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
26.5
26.5
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
P.D13 Fig.D-5 2kg
P.D13 Fig.D-7 2kg
P.D14 Fig.D-9 2.5kg
P.D14 Fig.D-11 2.5kg
P.D13 Fig.D-6 2.5kg
P.D13 Fig.D-8 2.5kg
P.D14 Fig.D-10 3kg
P.D14 Fig.D-12 3kg
50Hz 60Hz
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
25W
12
15
12
15
T25
T25W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.21/0.19/0.19
0.18/0.17/0.17
0.11/0.12/0.11/0.12
0.09/0.09/0.09/0.09
1350/1550/1600
1350/1550/1600
1350/1400/1600/1650
1300/1350/1550/1600
E
N・m kgf・m N kgf
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 3-Phase 25W
GearmotorGearmotor with Brake
G-Type〔Parallel Shaft〕 3-Phase 25WGearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series GTR-L Series
D15D14
Foot Mount Type Gearmotor with Brake
Flange Mount Type Gearmotor with Brake
G-Type〔Parallel Shaft〕 3-Phase 25WGearmotor with Brake
LGN-12 -3~120-T25LGN-12 -3~120-T25WFig.D-9
〔Round Weight 2.5kg〕
LGN-15 -160~360-T25LGN-15 -160~360-T25WFig.D-10
〔Round Weight 3kg〕 LGN-12M-T25 LGN-12M-T25W
LGN-15M-T25 LGN-15M-T25W
FGN-12 -3~120-T25FGN-12 -3~120-T25WFig.D-11
〔Round Weight 2.5kg〕
FGN-15 -160~360-T25FGN-15 -160~360-T25WFig.D-12
〔Round Weight 3kg〕 FGN-12M-T25 FGN-12M-T25W
FGN-15M-T25 FGN-15M-T25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
Foot Mount type Flange Mount type
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Performance Table/ Dimension
Performance Table/ Dimension
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D15D14
Foot Mount Type Gearmotor with Brake
Flange Mounted Type Gearmotor with Brake
G-Type〔Parallel Shaft〕 3-Phase 25WGearmotor with Brake
LGN-12 -3~120-T25LGN-12 -3~120-T25WFig.D-9
〔Round Weight 2.5kg〕
LGN-15 -160~360-T25LGN-15 -160~360-T25WFig.D-10
〔Round Weight 3kg〕 LGN-12M-T25 LGN-12M-T25W
LGN-15M-T25 LGN-15M-T25W
FGN-12 -3~120-T25FGN-12 -3~120-T25WFig.D-11
〔Round Weight 2.5kg〕
FGN-15 -160~360-T25FGN-15 -160~360-T25WFig.D-12
〔Round Weight 3kg〕 FGN-12M-T25 FGN-12M-T25W
FGN-15M-T25 FGN-15M-T25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
Foot Mount type Flange Mount type
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Performance Table/ Dimension
Performance Table/ Dimension
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D17D16
LG-15 -3~360-T40LG-15 -3~360-T40WFig.D-13
〔Round Weight 3kg〕 LG-15M-T40 LG-15M-T40W
FG-15 -3~360-T40FG-15 -3~360-T40WFig.D-14
〔Round Weight 3kg〕 FG-15M-T40 FG-15M-T40W
LGN-15 -3~360-T40LGN-15 -3~360-T40WFig.D-15
〔Round Weight 3kg〕 LGN-15M-T40 LGN-15M-T40W
FGN-15 -3~360-T40FGN-15 -3~360-T40WFig.D-16
〔Round Weight 3kg〕 FGN-15M-T40 FGN-15M-T40W
LG FG LGN FGN
3-phase 40W
15
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
15
30
35
45
50
55
65
70
70
70
70
70
70
70
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
P.D17 Fig.D-13 3kg
P.D17 Fig.D-14 3kg
P.D17 Fig.D-15 3kg
P.D17 Fig.D-16 3kg
50Hz 60Hz
*
*
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
40W
15
15
T40
T40W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.27/0.26/0.26
0.13/0.14/0.13/0.14
1350/1550/1550
1300/1350/1550/1600
E
N・m kgf・m N kgf
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
GearmotorGearmotor with BrakeG-Type〔Parallel Shaft〕 3-Phase 40W
Foot Mount Type Gearmotor Flange Mounted Type Gearmotor
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D17D16
LG-15 -3~360-T40LG-15 -3~360-T40WFig.D-13
〔Round Weight 3kg〕 LG-15M-T40 LG-15M-T40W
FG-15 -3~360-T40FG-15 -3~360-T40WFig.D-14
〔Round Weight 3kg〕 FG-15M-T40 FG-15M-T40W
LGN-15 -3~360-T40LGN-15 -3~360-T40WFig.D-15
〔Round Weight 3kg〕 LGN-15M-T40 LGN-15M-T40W
FGN-15 -3~360-T40FGN-15 -3~360-T40WFig.D-16
〔Round Weight 3kg〕 FGN-15M-T40 FGN-15M-T40W
LG FG LGN FGN
3-phase 40W
15
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
15
30
35
45
50
55
65
70
70
70
70
70
70
70
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
P.D17 Fig.D-13 3kg
P.D17 Fig.D-14 3kg
P.D17 Fig.D-15 3kg
P.D17 Fig.D-16 3kg
50Hz 60Hz
*
*
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
40W
15
15
T40
T40W
50/60/60
50/50/60/60
200/200/220
380/400/400/440
0.27/0.26/0.26
0.13/0.14/0.13/0.14
1350/1550/1550
1300/1350/1550/1600
E
N・m kgf・m N kgf
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
GearmotorGearmotor with BrakeG-Type〔Parallel Shaft〕 3-Phase 40W
Foot Mount Type Gearmotor Flange Mount Type Gearmotor
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D18 D19
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
●
●
1-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
Performance TableDimension diagram
Parallel Shaft
GearmotorGearmotor with BrakeReversible gearmotor
D18 D19
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
●
●
1-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
Performance TableDimension diagram
Parallel Shaft
GearmotorGearmotor with BrakeReversible gearmotor
D21D20
LG・LGR FG・LGR LGN FGN
1-phase 6W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
0.008
0.01
0.03
0.04
0.05
0.07
0.08
0.11
0.13
0.16
0.20
0.26
0.31
0.41
0.51
0.078
0.098
0.294
0.392
0.490
0.686
0.784
1.08
1.27
1.57
1.96
2.55
3.04
4.02
5.00
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
P.D21 Fig.D-17 1.5kg
P.D21 Fig.D-18 1.5kg
P.D21 Fig.D-19 1.5kg
P.D21 Fig.D-20 1.5kg
50Hz 60Hz
6W S06 50/60 0.17/0.17 1300/1600 2.510 E
Standard Voltage 〈4 pole, 30min, rating〉 6W S06 50/60
100/100
100/100 0.20/0.25 1300/1600 3.510 E
LG -10 -3~200-S06LGR-10 -3~200-S06Fig.D-17
〔Round Weight 1.5kg〕 LG-10M-S06 LGR-10M-S06
FG -10 -3~200-S06FGR-10 -3~200-S06Fig.D-18
〔Round Weight 1.5kg〕 FG-10M-S06 FGR-10M-S06
LGN-10 -3~200-S06Fig.D-19
〔Round Weight 1.5kg〕
FGN-10 -3~200-S06Fig.D-20
〔Round Weight 1.5kg〕
CAD Data: CAD Data:
CAD Data:LGN-10M-S06 CAD Data:FGN-10M-S06
MB
MB
MBMB
MBMB
N・m kgf・m N kgf
300
4
11.5
62
4567
754-φ5.5
φ10h7
136
61.5
2018
9
3042
30
6
300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1362018
9
7 3.5
24
61.5
300
4
11.5
62
4567
754-φ5.5
φ10h7
171
61.5
2018
9
3042
30
6
300 300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1712018
9
7 3.5
24
61.5
300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 6W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mounted Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D21D20
LG・LGR FG・LGR LGN FGN
1-phase 6W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
0.008
0.01
0.03
0.04
0.05
0.07
0.08
0.11
0.13
0.16
0.20
0.26
0.31
0.41
0.51
0.078
0.098
0.294
0.392
0.490
0.686
0.784
1.08
1.27
1.57
1.96
2.55
3.04
4.02
5.00
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
P.D21 Fig.D-17 1.5kg
P.D21 Fig.D-18 1.5kg
P.D21 Fig.D-19 1.5kg
P.D21 Fig.D-20 1.5kg
50Hz 60Hz
6W S06 50/60 0.17/0.17 1300/1600 2.510 E
Standard Voltage 〈4 pole, 30min, rating〉 6W S06 50/60
100/100
100/100 0.20/0.25 1300/1600 3.510 E
LG -10 -3~200-S06LGR-10 -3~200-S06Fig.D-17
〔Round Weight 1.5kg〕 LG-10M-S06 LGR-10M-S06
FG -10 -3~200-S06FGR-10 -3~200-S06Fig.D-18
〔Round Weight 1.5kg〕 FG-10M-S06 FGR-10M-S06
LGN-10 -3~200-S06Fig.D-19
〔Round Weight 1.5kg〕
FGN-10 -3~200-S06Fig.D-20
〔Round Weight 1.5kg〕
CAD Data: CAD Data:
CAD Data:LGN-10M-S06 CAD Data:FGN-10M-S06
MB
MB
MBMB
MBMB
N・m kgf・m N kgf
300
4
11.5
62
4567
754-φ5.5
φ10h7
136
61.5
2018
9
3042
30
6
300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1362018
9
7 3.5
24
61.5
300
4
11.5
62
4567
754-φ5.5
φ10h7
171
61.5
2018
9
3042
30
6
300 300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1712018
9
7 3.5
24
61.5
300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 6W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mount Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D23D22
S10
S10W
50/60
50/60
100/100
200/200
0.30/0.30
0.17/0.17
1300/1550
1300/1600
10W
3.5
1
10
10
E
S10
S10W
50/60
50/60
100/100
200/200
0.29/0.29
0.17/0.16
1300/1600
1300/1600
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
10W
4.5
1.2
10
10
E
LG -10 -3~200-S10LG -10 -3~200-S10WLGR-10 -3~200-S10LGR-10 -3~200-S10W
Fig.D-21
〔Round Weight 1.5kg〕
LG-10M-S10 LG-10M-S10W LGR-10M-S10 LGR-10M-S10W
FG -10 -3~200-S10FG -10 -3~200-S10WFGR-10 -3~200-S10FGR-10 -3~200-S10W
Fig.D-22
〔Round Weight 1.5kg〕
FG-10M-S10 FG-10M-S10W FGR-10M-S10 FGR-10M-S10W
LGN-10 -3~200-S10LGN-10 -3~200-S10WFig.D-23
〔Round Weight 1.5kg〕 LGN-10M-S10 LGN-10M-S10W
FGN-10 -3~200-S10FGN-10 -3~200-S10WFig.D-24
〔Round Weight 1.5kg〕 FGN-10M-S10 FGN-10M-S10W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1-phase 10W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
0.10
0.20
0.39
0.69
0.88
1.08
1.27
1.76
2.16
2.65
3.33
4.21
5.00
6.66
7.84
0.01
0.02
0.04
0.07
0.09
0.11
0.13
0.18
0.22
0.27
0.34
0.43
0.51
0.68
0.8
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
P.D23 Fig.D-21 1.5kg
P.D23 Fig.D-22 1.5kg
P.D23 Fig.D-23 1.5kg
P.D23 Fig.D-24 1.5kg
50Hz 60Hz N・m kgf・m N kgf
300
4
11.5
62
4567
754-φ5.5
φ10h7
171
61.5
2018
9
3042
30
6
300 300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1712018
9
7 3.5
24
61.5
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
136
61.5
2018
9
3042
30
6
300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1362018
9
7 3.5
24
61.5
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 10W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mounted Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D23D22
S10
S10W
50/60
50/60
100/100
200/200
0.30/0.30
0.17/0.17
1300/1550
1300/1600
10W
3.5
1
10
10
E
S10
S10W
50/60
50/60
100/100
200/200
0.29/0.29
0.17/0.16
1300/1600
1300/1600
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
10W
4.5
1.2
10
10
E
LG -10 -3~200-S10LG -10 -3~200-S10WLGR-10 -3~200-S10LGR-10 -3~200-S10W
Fig.D-21
〔Round Weight 1.5kg〕
LG-10M-S10 LG-10M-S10W LGR-10M-S10 LGR-10M-S10W
FG -10 -3~200-S10FG -10 -3~200-S10WFGR-10 -3~200-S10FGR-10 -3~200-S10W
Fig.D-22
〔Round Weight 1.5kg〕
FG-10M-S10 FG-10M-S10W FGR-10M-S10 FGR-10M-S10W
LGN-10 -3~200-S10LGN-10 -3~200-S10WFig.D-23
〔Round Weight 1.5kg〕 LGN-10M-S10 LGN-10M-S10W
FGN-10 -3~200-S10FGN-10 -3~200-S10WFig.D-24
〔Round Weight 1.5kg〕 FGN-10M-S10 FGN-10M-S10W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1-phase 10W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
0.10
0.20
0.39
0.69
0.88
1.08
1.27
1.76
2.16
2.65
3.33
4.21
5.00
6.66
7.84
0.01
0.02
0.04
0.07
0.09
0.11
0.13
0.18
0.22
0.27
0.34
0.43
0.51
0.68
0.8
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
P.D23 Fig.D-21 1.5kg
P.D23 Fig.D-22 1.5kg
P.D23 Fig.D-23 1.5kg
P.D23 Fig.D-24 1.5kg
50Hz 60Hz N・m kgf・m N kgf
300
4
11.5
62
4567
754-φ5.5
φ10h7
171
61.5
2018
9
3042
30
6
300 300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1712018
9
7 3.5
24
61.5
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
136
61.5
2018
9
3042
30
6
300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
1362018
9
7 3.5
24
61.5
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 10W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mount Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D25D24
S15
S15W
50/60
50/60
0.39/0.35
0.21/0.19
1350/1650
1350/1650
15W
5
1.2
12
12
E
S15
S15W
50/60
50/60
0.35/0.40
0.20/0.20
1400/1700
1400/1700
100/100
200/200
100/100
200/200
15W
6
1.5
12
12
E
LG -12 -3~360-S15LG -12 -3~360-S15WLGR-12 -3~360-S15LGR-12 -3~360-S15W
Fig.D-25
〔Round Weight 2kg〕
LG-12M-S15 LG-12M-S15W LGR-12M-S15 LGR-12M-S15W
FG -12 -3~360-S15FG -12 -3~360-S15WFGR-12 -3~360-S15FGR-12 -3~360-S15W
Fig.D-26
〔Round Weight 2kg〕
FG-12M-S15 FG-12M-S15W FGR-12M-S15 FGR-12M-S15W
LGN-12 -3~360-S15LGN-12 -3~360-S15WFig.D-27
〔Round Weight 2kg〕 LGN-12M-S15 LGN-12M-S15W
FGN-12 -3~360-S15FGN-12 -3~360-S15WFig.D-28
〔Round Weight 2kg〕 FGN-12M-S15 FGN-12M-S15W
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
1-phase 15W
12P.D25 Fig.D-25 2kg
P.D25 Fig.D-26 2kg
P.D25 Fig.D-27 2kg
P.D25 Fig.D-28 2kg
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 15W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mounted Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D25D24
S15
S15W
50/60
50/60
0.39/0.35
0.21/0.19
1350/1650
1350/1650
15W
5
1.2
12
12
E
S15
S15W
50/60
50/60
0.35/0.40
0.20/0.20
1400/1700
1400/1700
100/100
200/200
100/100
200/200
15W
6
1.5
12
12
E
LG -12 -3~360-S15LG -12 -3~360-S15WLGR-12 -3~360-S15LGR-12 -3~360-S15W
Fig.D-25
〔Round Weight 2kg〕
LG-12M-S15 LG-12M-S15W LGR-12M-S15 LGR-12M-S15W
FG -12 -3~360-S15FG -12 -3~360-S15WFGR-12 -3~360-S15FGR-12 -3~360-S15W
Fig.D-26
〔Round Weight 2kg〕
FG-12M-S15 FG-12M-S15W FGR-12M-S15 FGR-12M-S15W
LGN-12 -3~360-S15LGN-12 -3~360-S15WFig.D-27
〔Round Weight 2kg〕 LGN-12M-S15 LGN-12M-S15W
FGN-12 -3~360-S15FGN-12 -3~360-S15WFig.D-28
〔Round Weight 2kg〕 FGN-12M-S15 FGN-12M-S15W
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
1-phase 15W
12P.D25 Fig.D-25 2kg
P.D25 Fig.D-26 2kg
P.D25 Fig.D-27 2kg
P.D25 Fig.D-28 2kg
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 15W
Gearmotor・Reversible gearmotorGearmotor with Brake
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mount Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D27D26
Foot Mount Type Gearmotor/Reversible gearmotorGearmotor/Gearmotor with Brake
Flange Mounted Type Gearmotor/Reversible gearmotor
S25
S25W
100/100
200/200
0.48/0.48
0.44/0.45
0.26/0.25
0.23/0.24
1350/1600
1350/1650
1350/1600
1350/1650
25W
7
7
1.7
1.7
12
15
12
15
0.55/0.65
0.50/0.65
0.26/0.33
0.26/0.35
1400/1650
1400/1650
1400/1650
1400/1650
10
10
2.5
2.5
12
15
12
15
E
Reversible gearmotor
S25
S25W
100/100
200/200
50/60
50/60
50/60
50/60
25W E
LG -12 -3~120-S25LG -12 -3~120-S25WLGR-12 -3~120-S25LGR-12 -3~120-S25W
Fig.D-29
〔Round Weight 2kg〕
LG-12M-S25 LG-12M-S25W LGR-12M-S25 LGR-12M-S25W
LG -15 -160~360-S25LG -15 -160~360-S25WLGR-15 -160~360-S25LGR-15 -160~360-S25W
Fig.D-30
〔Round Weight 2.5kg〕
LG-15M-S25 LG-15M-S25W LGR-15M-S25 LGR-15M-S25W
FG -12 -3~120-S25FG -12 -3~120-S25WFGR-12 -3~120-S25FGR-12 -3~120-S25W
Fig.D-31
〔Round Weight 2kg〕
FG -15 -160~360-S25FG -15 -160~360-S25WFGR-15 -160~360-S25FGR-15 -160~360-S25W
Fig.D-32
〔Round Weight 2.5kg〕
FG-15M-S25 FG-15M-S25W FGR-15M-S25 FGR-15M-S25W
FG-12M-S25 FG-12M-S25W FGR-12M-S25 FGR-12M-S25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMBMBMB
MBMBMBMB
*
*
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
26.5
26.5
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
2.7
2.7
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
1-phase 25W
12
15
P.D27 Fig.D-29 2kg
P.D27 Fig.D-31 2kg
P.D28 Fig.D-33 2.5kg
P.D28 Fig.D-35 2.5kg
P.D27 Fig.D-30 2.5kg
P.D27 Fig.D-32 2.5kg
P.D28 Fig.D-34 3kg
P.D28 Fig.D-36 3kg
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W G-Type〔Parallel Shaft〕 1-Phase 25W
Gearmotor・Reversible gearmotorGearmotor with Brake Gearmotor・Reversible gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series GTR-L Series
D27D26
Foot Mount Type Gearmotor/Reversible gearmotorGearmotor/Gearmotor with Brake
Flange Mount Type Gearmotor/Reversible gearmotor
S25
S25W
100/100
200/200
0.48/0.48
0.44/0.45
0.26/0.25
0.23/0.24
1350/1600
1350/1650
1350/1600
1350/1650
25W
7
7
1.7
1.7
12
15
12
15
0.55/0.65
0.50/0.65
0.26/0.33
0.26/0.35
1400/1650
1400/1650
1400/1650
1400/1650
10
10
2.5
2.5
12
15
12
15
E
Reversible gearmotor
S25
S25W
100/100
200/200
50/60
50/60
50/60
50/60
25W E
LG -12 -3~120-S25LG -12 -3~120-S25WLGR-12 -3~120-S25LGR-12 -3~120-S25W
Fig.D-29
〔Round Weight 2kg〕
LG-12M-S25 LG-12M-S25W LGR-12M-S25 LGR-12M-S25W
LG -15 -160~360-S25LG -15 -160~360-S25WLGR-15 -160~360-S25LGR-15 -160~360-S25W
Fig.D-30
〔Round Weight 2.5kg〕
LG-15M-S25 LG-15M-S25W LGR-15M-S25 LGR-15M-S25W
FG -12 -3~120-S25FG -12 -3~120-S25WFGR-12 -3~120-S25FGR-12 -3~120-S25W
Fig.D-31
〔Round Weight 2kg〕
FG -15 -160~360-S25FG -15 -160~360-S25WFGR-15 -160~360-S25FGR-15 -160~360-S25W
Fig.D-32
〔Round Weight 2.5kg〕
FG-15M-S25 FG-15M-S25W FGR-15M-S25 FGR-15M-S25W
FG-12M-S25 FG-12M-S25W FGR-12M-S25 FGR-12M-S25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMBMBMB
MBMBMBMB
*
*
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
26.5
26.5
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
2.7
2.7
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
1-phase 25W
12
15
P.D27 Fig.D-29 2kg
P.D27 Fig.D-31 2kg
P.D28 Fig.D-33 2.5kg
P.D28 Fig.D-35 2.5kg
P.D27 Fig.D-30 2.5kg
P.D27 Fig.D-32 2.5kg
P.D28 Fig.D-34 3kg
P.D28 Fig.D-36 3kg
300153
2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300153
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W G-Type〔Parallel Shaft〕 1-Phase 25W
Gearmotor・Reversible gearmotorGearmotor with Brake Gearmotor・Reversible gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series GTR-L Series
D29D28
G-Type〔Parallel Shaft〕 1-Phase 25WGearmotor with Brake
LGN-12 -3~120-S25LGN-12 -3~120-S25WFig.D-33
〔Round Weight 2.5kg〕
LGN-15 -160~360-S25LGN-15 -160~360-S25WFig.D-34
〔Round Weight 3kg〕 LGN-12M-S25 LGN-12M-S25W
LGN-15M-S25 LGN-15M-S25W
FGN-12 -3~120-S25FGN-12 -3~120-S25WFig.D-35
〔Round Weight 2.5kg〕
FGN-15 -160~360-S25FGN-15 -160~360-S25WFig.D-36
〔Round Weight 3kg〕 FGN-12M-S25 FGN-12M-S25W
FGN-15M-S25 FGN-15M-S25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Gearmotor
Flange Mount Type Gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D29D28
G-Type〔Parallel Shaft〕 1-Phase 25WGearmotor with Brake
LGN-12 -3~120-S25LGN-12 -3~120-S25WFig.D-33
〔Round Weight 2.5kg〕
LGN-15 -160~360-S25LGN-15 -160~360-S25WFig.D-34
〔Round Weight 3kg〕 LGN-12M-S25 LGN-12M-S25W
LGN-15M-S25 LGN-15M-S25W
FGN-12 -3~120-S25FGN-12 -3~120-S25WFig.D-35
〔Round Weight 2.5kg〕
FGN-15 -160~360-S25FGN-15 -160~360-S25WFig.D-36
〔Round Weight 3kg〕 FGN-12M-S25 FGN-12M-S25W
FGN-15M-S25 FGN-15M-S25W
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMB
MBMB
MBMB
MBMB
300300
1882220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300
300188
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Gearmotor
Flange Mounted Type Gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D31D30
S40
S40W
50/60
50/60
0.61/0.66
0.29/0.34
1350/1650
1350/1600
40W
10
2.5
15
15
E
S40
S40W
50/60
50/60
0.75/0.88
0.37/0.41
1400/1650
1400/1650
100/100
200/200
100/100
200/200
40W
14
3.5
15
15
E
LG -15 -3~360-S40LG -15 -3~360-S40WLGR-15 -3~360-S40LGR-15 -3~360-S40W
Fig.D-37
〔Round Weight 2.5kg〕
LG-15M-S40 LG-15M-S40W LGR-15M-S40 LGR-15M-S40W
FG -15 -3~360-S40FG -15 -3~360-S40WFGR-15 -3~360-S40FGR-15 -3~360-S40W
Fig.D-38
〔Round Weight 2.5kg〕
FG-15M-S40 FG-15M-S40W FGR-15M-S40 FGR-15M-S40W
LGN-15 -3~360-S40LGN-15 -3~360-S40WFig.D-39
〔Round Weight 3kg〕 LGN-15M-S40 LGN-15M-S40W
FGN-15 -3~360-S40FGN-15 -3~360-S40WFig.D-40
〔Round Weight 3kg〕 FGN-15M-S40 FGN-15M-S40W*
*
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
1-phase 40W
15P.D31 Fig.D-37 2.5kg
P.D31 Fig.D-38 2.5kg
P.D31 Fig.D-39 3kg
P.D31 Fig.D-40 3kg
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
15
30
35
45
50
55
65
70
70
70
70
70
70
70
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 40W
Gearmotor・Reversible gearmotorGearmotor with Brake
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mounted Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mounted Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D31D30
S40
S40W
50/60
50/60
0.61/0.66
0.29/0.34
1350/1650
1350/1600
40W
10
2.5
15
15
E
S40
S40W
50/60
50/60
0.75/0.88
0.37/0.41
1400/1650
1400/1650
100/100
200/200
100/100
200/200
40W
14
3.5
15
15
E
LG -15 -3~360-S40LG -15 -3~360-S40WLGR-15 -3~360-S40LGR-15 -3~360-S40W
Fig.D-37
〔Round Weight 2.5kg〕
LG-15M-S40 LG-15M-S40W LGR-15M-S40 LGR-15M-S40W
FG -15 -3~360-S40FG -15 -3~360-S40WFGR-15 -3~360-S40FGR-15 -3~360-S40W
Fig.D-38
〔Round Weight 2.5kg〕
FG-15M-S40 FG-15M-S40W FGR-15M-S40 FGR-15M-S40W
LGN-15 -3~360-S40LGN-15 -3~360-S40WFig.D-39
〔Round Weight 3kg〕 LGN-15M-S40 LGN-15M-S40W
FGN-15 -3~360-S40FGN-15 -3~360-S40WFig.D-40
〔Round Weight 3kg〕 FGN-15M-S40 FGN-15M-S40W*
*
*
*
CAD Data: CAD Data:
CAD Data: CAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LG・LGR FG・LGR LGN FGN
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
1/300
1/360
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
5
4.2
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
6
5
50Hz 60Hz N・m kgf・m N kgf
1-phase 40W
15P.D31 Fig.D-37 2.5kg
P.D31 Fig.D-38 2.5kg
P.D31 Fig.D-39 3kg
P.D31 Fig.D-40 3kg
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
15
30
35
45
50
55
65
70
70
70
70
70
70
70
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
300
4-φ6.5
5
17 65
90104
97.5
1612522
13
8
374056
90.5
φ15h7
300
4-φ6.5
φ15h7
90.5
1612522
13
9 3
29
525
17
38 3891
9151
(φ40)
300
4-φ6.5
5
17 65
90104
97.5
1962522
13
8
374056
90.5
φ15h7
300300
4-φ6.5
φ15h7
90.5
1962522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D6
Option P.E110P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 40W
Gearmotor・Reversible gearmotorGearmotor with Brake
Gearmotor/Gearmotor with Brake
Reversible gearmotor
Foot Mount Type Gearmotor/Reversible gearmotor Flange Mount Type Gearmotor/Reversible gearmotor
Foot Mount Type Gearmotor with Brake Flange Mount Type Gearmotor with Brake
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Standard Voltage 〈4 pole, 30min, rating〉
Double Voltage 〈4 pole, 30min, rating〉
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
Rated Current (A)
Rated Rotation Speed (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
Gearmotor Reversible gearmotor
Gearmotor with BrakeMotor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable Torque
Output Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
GTR-L Series
D32 D33
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
1-Phase
6W~40W
100V 50/60Hz
Class E
Capacitor Start
Totally Enclosed
4
Continuous Rating
Spur gear and Helical gear
Grease Lubrication
New JIS Key(JIS 1301-1976 class)
S43C
Aluminium die-cast
-10℃~40℃
85%max.(without any dew condensation)
1,000m max.
Indoors
Anion painting, Acrylic paint
Grey(Mansel code: 9B6/0.5)
No restriction in the mounting angle.(horizontally, vertically or heeling angle)
Well ventilated place free from corrosive gas, explosive gas vapor and/or dust.
Motor Part
Ambient Conditions
Painting
Mounting Direction
Speed Reduction Part
Number of phase
Capacity
Power Source
Insulation Classification
Starting Method
Protective cooling Method
Number of Pole
Rating
Reduction Method
Lubrication
Output Shaft
Output Shaft Material
Case Material
Ambient Temperature
Ambient Humidity
Altitude
Installation Location
Painting Method
Painting Color
Environment
Model and Type DesignationStandard Model Lineup
Parallel Shaft
Speed control GearmotorSpeed controlGearmotor with Brake
D32 D33
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
1-Phase
6W~40W
100V 50/60Hz
Class E
Capacitor Start
Totally Enclosed
4
Continuous Rating
Spur gear and Helical gear
Grease Lubrication
New JIS Key(JIS 1301-1976 class)
S43C
Aluminium die-cast
-10℃~40℃
85%max.(without any dew condensation)
1,000m max.
Indoors
Anion painting, Acrylic paint
Grey(Mansel code: 9B6/0.5)
No restriction in the mounting angle.(horizontally, vertically or heeling angle)
Well ventilated place free from corrosive gas, explosive gas vapor and/or dust.
Motor Part
Ambient Conditions
Painting
Mounting Direction
Speed Reduction Part
Number of phase
Capacity
Power Source
Insulation Classification
Starting Method
Protective cooling Method
Number of Pole
Rating
Reduction Method
Lubrication
Output Shaft
Output Shaft Material
Case Material
Ambient Temperature
Ambient Humidity
Altitude
Installation Location
Painting Method
Painting Color
Environment
Model and Type DesignationStandard Model Lineup
Parallel Shaft
Speed control GearmotorSpeed controlGearmotor with Brake
D35D34
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/20010
LGU FGU LGP FGP
LGPN FGPN
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/20010
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36012
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36015
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120
1/160 1/200 1/240 1/300 1/360
12
15
P-Type(Controller Sells Separately) U-TypeGTR-L Series Speed control Gearmotor/Speed control Gearmotor with Brake are lassified by codes as shown below. Specify these codes in your inquiry and order.
①Classification by Mount Form
②Series Name
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
L
F
G
Blank
U
P
PN
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
S06
S10
S15
S25
S40
Blank
W
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Speed control Gearmotor
: With Speed control Gearmotor
: With Speed control Gearmotor with Brake
: Metal type
: Bearing type
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: P-Type Terminal Box
: Standard Specs.
: Mark for Additional Specs.
U-Type(With Controller)
P-Type(Controller Sells Separately)
P-Type(Controller Sells Separately)
1-phase: 100V/50Hz、100V/60Hz
1-phase: 200V/50Hz、200V/60Hz(except for 6W)
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
L Series(Parallel Shaft) Model and Type Designation Standard Model Lineup
The models enclosed with orange color bold line are low torque type. Special care should be given to the allowable torque in the performance table.
Note 1)
Controller■Type DesignationGTR-L Series controllers are classified by codes as shown below.
These codes are required for your inquiry and/or order.
Blank L: U-Type
: P-Type0: variable speed only (U-Type only) 1: variable speed + instant stop 2: variable speed + instant stop + slow start + slow down 3: variable speed + instant stop + slow start + slow down + parallel running
SC: Speed Controller (generic name)
10 : single-phase 100V 20 : single-phase 200V
Function
Voltage
U: U-Type (Attached with gearmotors) P: P-Type (Not included in gearmotors)
Type Voltage Function Motor Type
SC 10 1 LP
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
LG 15 240 S25F W
MMN
U
G 15 360 S40F BPNC X T6
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
③Classification by Motor Type
⑪Spec. DesignationNote: Spec. Designation does not appear on
the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Type Frame Number Reduction Ratio4P Motor
Capacity
Speed control Gearmotor
Speed control Gearmotor with Brake
1-Phase 6W
1-Phase 10W
1-Phase 15W
1-Phase 40W
1-Phase 25W
GTR-L Series
D35D34
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/20010
LGU FGU LGP FGP
LGPN FGPN
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/20010
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36012
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120 1/160 1/200 1/240 1/300 1/36015
1/3 1/5 1/10 1/15 1/20 1/25 1/30 1/40 1/50
1/60 1/80 1/100 1/120
1/160 1/200 1/240 1/300 1/360
12
15
P-Type(Controller Sells Separately) U-TypeGTR-L Series Speed control Gearmotor/Speed control Gearmotor with Brake are lassified by codes as shown below. Specify these codes in your inquiry and order.
①Classification by Mount Form
②Series Name
④Frame No. and Diameter of Output shaft
⑤Bearing type
⑥Reduction Ratio
⑦Motor Designation and Capacity
⑧⑨Option
⑩Auxiliary Mark
L
F
G
Blank
U
P
PN
Output Shaft Diameter
M
B
3 : 1/3 ~ 360 : 1/360
S06
S10
S15
S25
S40
Blank
W
C
Blank
X
: Foot Mount
: Flange Mount
: Parallel Shaft
: With Motor
: With Speed control Gearmotor
: With Speed control Gearmotor
: With Speed control Gearmotor with Brake
: Metal type
: Bearing type
: 1-phase 6W
: 1-phase 10W
: 1-phase 15W
: 1-phase 25W
: 1-phase 40W
: Standard Specifications
: High Voltage
: P-Type Terminal Box
: Standard Specs.
: Mark for Additional Specs.
U-Type(With Controller)
P-Type(Controller Sells Separately)
P-Type(Controller Sells Separately)
1-phase: 100V/50Hz、100V/60Hz
1-phase: 200V/50Hz、200V/60Hz(except for 6W)
Position indicator for lead-wire, terminal box Refer to the indication mark list in P. E54 for details.
L Series(Parallel Shaft) Model and Type Designation Standard Model Lineup
The models enclosed with orange color bold line are low torque type. Special care should be given to the allowable torque in the performance table.
Note 1)
Controller■Type DesignationGTR-L Series controllers are classified by codes as shown below.
These codes are required for your inquiry and/or order.
Blank L: U-Type
: P-Type0: variable speed only (U-Type only) 1: variable speed + instant stop 2: variable speed + instant stop + slow start + slow down 3: variable speed + instant stop + slow start + slow down + parallel running
SC: Speed Controller (generic name)
10 : single-phase 100V 20 : single-phase 200V
Function
Voltage
U: U-Type (Attached with gearmotors) P: P-Type (Not included in gearmotors)
Type Voltage Function Motor Type
SC 10 1 LP
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Model and Type Designation
Model and Type Designation
① ② ④ ⑤ ③
G 10 3
⑥
S06
⑦ ⑧ ⑨ ⑪ ⑩
LG 15 240 S25F W
MMN
U
G 15 360 S40F BPNC X T6
Type Shaft Arrangement
Auxiliary Mark
Spec. Designation
Frame Number
Motor Capacity OptionReduction
Ratio
③Classification by Motor Type
⑪Spec. DesignationNote: Spec. Designation does not appear on
the product type designation in the nameplate. It is specified on the additional numbers in the nameplate.
Type Frame Number Reduction Ratio4P Motor
Capacity
Speed control Gearmotor
Speed control Gearmotor with Brake
1-Phase 6W
1-Phase 10W
1-Phase 15W
1-Phase 40W
1-Phase 25W
GTR-L Series
D36 D37
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
●
●
●
●
1-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. Allowable torques at high speed (N・m{kgf・m}) indicate the value in the range of high rotating speed(rpm). The percentage(%) at the allowable torque of 50% indicate the percentage against the allowable torque at high speed. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
Performance TableDimension diagram
Speed control GearmotorSpeed controlGearmotor with Brake
Parallel Shaft
D36 D37
GTR - LSe r i e s
GType
Parallel Shaft
Gearmotor
●
●
●
●
1-Phase
The output rotation speed is the value corresponds to the motor synchronous speed and the nominal reduction ratio. Allowable torques at high speed (N・m{kgf・m}) indicate the value in the range of high rotating speed(rpm). The percentage(%) at the allowable torque of 50% indicate the percentage against the allowable torque at high speed. The Shaded areas in the performance table shows that in case gearmotors are wired (forward rotation) according to the diagram shown on page E30, the shaft rotates clock wise when viewing from output side. (Reter to the diagram shown below.)
【Remarks】
Performance TableDimension diagram
Speed control GearmotorSpeed controlGearmotor with Brake
Parallel Shaft
D39D38
G-Type〔Parallel Shaft〕 1-Phase 6W
Speed control gearmotorsSpeed control brake motors
LGU・LGP FGU・FGP LGPN FGPN
1-phase 6W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
0.078
0.098
0.294
0.392
0.490
0.686
0.784
1.08
1.27
1.57
1.96
2.55
3.04
4.02
5.0
0.008
0.01
0.03
0.04
0.05
0.07
0.08
0.11
0.13
0.16
0.20
0.26
0.31
0.41
0.51
P.D39 Fig.D-41 1.5kg
P.D39 Fig.D-42 1.5kg
P.D39 Fig.D-43 1.5kg
P.D39 Fig.D-44 1.5kg
50Hz 60Hz kgf・mN・mkgfN
6W S06 50/60100/100 0.25/0.25 500~1300/50~1600 2.510 ELGU-10 -3~200-S06LGP-10 -3~200-S06Fig.D-41
〔Round Weight 1.5kg〕
FGU-10 -3~200-S06FGP-10 -3~200-S06Fig.D-42
〔Round Weight 1.5kg〕
LGPN-10 -3~200-S06Fig.D-43
〔Round Weight 1.5kg〕
FGPN-10 -3~200-S06Fig.D-44
〔Round Weight 1.5kg〕
50rpm (%)
100
■100V1-Phase 6W
MBMB
MBMB
MB
MB
LGU-10M-S06 LGP-10M-S06CAD Data: FGU-10M-S06
FGP-10M-S06CAD Data:
CAD Data: LGPN-10M-S06 CAD Data: FGPN-10M-S06
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300
146.8300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
146.8
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300300
181.3300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
300300
181.3
50Hz60Hz
500 1000 1500Rotation Speed〔rpm〕
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Speed control gearmotor with Brake Flange Mounted Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mounted Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Torque〔
%〕
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
GTR-L Series
D39D38
G-Type〔Parallel Shaft〕 1-Phase 6W
Speed control gearmotorsSpeed control brake motors
LGU・LGP FGU・FGP LGPN FGPN
1-phase 6W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
0.078
0.098
0.294
0.392
0.490
0.686
0.784
1.08
1.27
1.57
1.96
2.55
3.04
4.02
5.0
0.008
0.01
0.03
0.04
0.05
0.07
0.08
0.11
0.13
0.16
0.20
0.26
0.31
0.41
0.51
P.D39 Fig.D-41 1.5kg
P.D39 Fig.D-42 1.5kg
P.D39 Fig.D-43 1.5kg
P.D39 Fig.D-44 1.5kg
50Hz 60Hz kgf・mN・mkgfN
6W S06 50/60100/100 0.25/0.25 500~1300/50~1600 2.510 ELGU-10 -3~200-S06LGP-10 -3~200-S06Fig.D-41
〔Round Weight 1.5kg〕
FGU-10 -3~200-S06FGP-10 -3~200-S06Fig.D-42
〔Round Weight 1.5kg〕
LGPN-10 -3~200-S06Fig.D-43
〔Round Weight 1.5kg〕
FGPN-10 -3~200-S06Fig.D-44
〔Round Weight 1.5kg〕
50rpm (%)
100
■100V1-Phase 6W
MBMB
MBMB
MB
MB
LGU-10M-S06 LGP-10M-S06CAD Data: FGU-10M-S06
FGP-10M-S06CAD Data:
CAD Data: LGPN-10M-S06 CAD Data: FGPN-10M-S06
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300
146.8300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
146.8
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300300
181.3300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
300300
181.3
50Hz60Hz
500 1000 1500Rotation Speed〔rpm〕
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
Foot Mount Type Speed control gearmotor with Brake Flange Mount Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mount Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Torque〔
%〕
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
GTR-L Series
D41D40
10W
S10
S10W
50/60
50/60
100/100
200/200
0.35/0.35
0.2/0.2
500~1300/500~1600
450~1300/500~1600
3.5
1
10
10
E
LGU-10 -3~200-S10LGU-10 -3~200-S10WLGP-10 -3~200-S10LGP-10 -3~200-S10W
Fig.D-45
〔Round Weight 1.5kg〕
FGU-10 -3~200-S10FGU-10 -3~200-S10WFGP-10 -3~200-S10FGP-10 -3~200-S10W
Fig.D-46
〔Round Weight 1.5kg〕
LGPN-10 -3~200-S10LGPN-10 -3~200-S10WFig.D-47
〔Round Weight 1.5kg〕
FGPN-10 -3~200-S10FGPN-10 -3~200-S10WFig.D-48
〔Round Weight 1.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 10W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
0.01
0.02
0.04
0.07
0.09
0.11
0.13
0.18
0.22
0.27
0.34
0.43
0.51
0.68
0.8
0.10
0.20
0.39
0.69
0.88
1.08
1.27
1.76
2.16
2.65
3.33
4.21
5.00
6.66
7.84
P.D41 Fig.D-45 1.5kg
P.D41 Fig.D-46 1.5kg
P.D41 Fig.D-47 1.5kg
P.D41 Fig.D-48 1.5kg
50Hz 60Hz50rpm (%)
70
■100V ■200V1-Phase 10W
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LGU-10M-S10 LGU-10M-S10W LGP-10M-S10 LGP-10M-S10W
LGPN-10M-S10 LGPN-10M-S10W
CAD Data: FGU-10M-S10 FGU-10M-S10W FGP-10M-S10 FGP-10M-S10W
CAD Data:
CAD Data: FGPN-10M-S10 FGPN-10M-S10WCAD Data:
kgf・mN・mkgfN
(100V) (200V)
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300
146.8300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
146.8
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300300
181.3300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
300300
181.3
50Hz60Hz
500 1000 1500Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 10W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mounted Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mounted Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
GTR-L Series
D41D40
10W
S10
S10W
50/60
50/60
100/100
200/200
0.35/0.35
0.2/0.2
500~1300/500~1600
450~1300/500~1600
3.5
1
10
10
E
LGU-10 -3~200-S10LGU-10 -3~200-S10WLGP-10 -3~200-S10LGP-10 -3~200-S10W
Fig.D-45
〔Round Weight 1.5kg〕
FGU-10 -3~200-S10FGU-10 -3~200-S10WFGP-10 -3~200-S10FGP-10 -3~200-S10W
Fig.D-46
〔Round Weight 1.5kg〕
LGPN-10 -3~200-S10LGPN-10 -3~200-S10WFig.D-47
〔Round Weight 1.5kg〕
FGPN-10 -3~200-S10FGPN-10 -3~200-S10WFig.D-48
〔Round Weight 1.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 10W
10
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
6
8
14
21
25
28
32
35
35
35
35
35
35
35
35
59
78
137
206
245
274
314
343
343
343
343
343
343
343
343
0.01
0.02
0.04
0.07
0.09
0.11
0.13
0.18
0.22
0.27
0.34
0.43
0.51
0.68
0.8
0.10
0.20
0.39
0.69
0.88
1.08
1.27
1.76
2.16
2.65
3.33
4.21
5.00
6.66
7.84
P.D41 Fig.D-45 1.5kg
P.D41 Fig.D-46 1.5kg
P.D41 Fig.D-47 1.5kg
P.D41 Fig.D-48 1.5kg
50Hz 60Hz50rpm (%)
70
■100V ■200V1-Phase 10W
MBMBMBMB
MBMBMBMB
MBMB
MBMB
LGU-10M-S10 LGU-10M-S10W LGP-10M-S10 LGP-10M-S10W
LGPN-10M-S10 LGPN-10M-S10W
CAD Data: FGU-10M-S10 FGU-10M-S10W FGP-10M-S10 FGP-10M-S10W
CAD Data:
CAD Data: FGPN-10M-S10 FGPN-10M-S10WCAD Data:
kgf・mN・mkgfN
(100V) (200V)
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300
146.8300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
146.8
300
300
4
11.5
62
4567
754-φ5.5
φ10h7
61.5
2018
9
3042
30
6
300300
181.3300
416
3411.5
25 2562
62
4-φ5.5
(φ26)
φ10h7
2018
9
7 3.5
24
61.5
300300
181.3
50Hz60Hz
500 1000 1500Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. Be sure to read the cautions stated on Page D19.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 10W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mount Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mount Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
GTR-L Series
D43D42
15W
S15
S15W
50/60
50/60
100/100
200/200
0.6/0.6
0.3/0.3
500~1350/550~1650
600~1400/750~1700
6
1.5
12
12
E
LGU-12 -3~360-S15LGU-12 -3~360-S15WLGP-12 -3~360-S15LGP-12 -3~360-S15W
Fig.D-49
〔Round Weight 2kg〕
LGU-12M-S15 LGU-12M-S15W LGP-12M-S15 LGP-12M-S15W
LGPN-12M-S15 LGPN-12M-S15W
FGU-12 -3~360-S15FGU-12 -3~360-S15WFGP-12 -3~360-S15FGP-12 -3~360-S15W
Fig.D-50
〔Round Weight 2kg〕
LGPN-12 -3~360-S15LGPN-12 -3~360-S15WFig.D-51
〔Round Weight 2.5kg〕
FGPN-12 -3~360-S15FGPN-12 -3~360-S15WFig.D-52
〔Round Weight 2.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 15W
12
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
P.D43 Fig.D-49 2kg
P.D43 Fig.D-50 2kg
P.D43 Fig.D-51 2.5kg
P.D43 Fig.D-52 2.5kg
50Hz 60Hz50rpm (%)
90(100V)
75(200V)
70(100V)
60(200V)
1/300
1/360
5
4.2
6
5
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
■100V ■200V
CAD Data: FGU-12M-S15 FGU-12M-S15W FGP-12M-S15 FGP-12M-S15W
CAD Data:
CAD Data: FGPN-12M-S15 FGPN-12M-S15WCAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
kgf・mN・mkgfN
*
*
300 2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
163.8300
3002220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
163.8
3003002220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
198.3300
198.32220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 15W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mounted Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mounted Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
1-Phase 15W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series
D43D42
15W
S15
S15W
50/60
50/60
100/100
200/200
0.6/0.6
0.3/0.3
500~1350/550~1650
600~1400/750~1700
6
1.5
12
12
E
LGU-12 -3~360-S15LGU-12 -3~360-S15WLGP-12 -3~360-S15LGP-12 -3~360-S15W
Fig.D-49
〔Round Weight 2kg〕
LGU-12M-S15 LGU-12M-S15W LGP-12M-S15 LGP-12M-S15W
LGPN-12M-S15 LGPN-12M-S15W
FGU-12 -3~360-S15FGU-12 -3~360-S15WFGP-12 -3~360-S15FGP-12 -3~360-S15W
Fig.D-50
〔Round Weight 2kg〕
LGPN-12 -3~360-S15LGPN-12 -3~360-S15WFig.D-51
〔Round Weight 2.5kg〕
FGPN-12 -3~360-S15FGPN-12 -3~360-S15WFig.D-52
〔Round Weight 2.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 15W
12
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
10
20
30
35
40
45
50
50
50
50
50
50
50
50
50
50
0.02
0.03
0.07
0.10
0.13
0.17
0.20
0.27
0.34
0.40
0.51
0.64
0.76
1.0
1.3
1.5
P.D43 Fig.D-49 2kg
P.D43 Fig.D-50 2kg
P.D43 Fig.D-51 2.5kg
P.D43 Fig.D-52 2.5kg
50Hz 60Hz50rpm (%)
90(100V)
75(200V)
70(100V)
60(200V)
1/300
1/360
5
4.2
6
5
50
50
98
196
294
343
392
441
490
490
490
490
490
490
490
490
490
490
490
490
1.5
1.5
0.20
0.29
0.69
0.98
1.27
1.67
1.96
2.65
3.33
3.92
5.00
6.27
7.45
9.80
12.7
14.7
14.7
14.7
■100V ■200V
CAD Data: FGU-12M-S15 FGU-12M-S15W FGP-12M-S15 FGP-12M-S15W
CAD Data:
CAD Data: FGPN-12M-S15 FGPN-12M-S15WCAD Data:
MBMBMBMB
MBMBMBMB
MBMB
MBMB
kgf・mN・mkgfN
*
*
300 2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
163.8300
3002220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
163.8
3003002220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
198.3300
198.32220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 15W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mount Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mount Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
1-Phase 15W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series
D45D44
Foot Mount Type Speed control gearmotor
Flange Mounted Type Speed control gearmotor
25W
S25
S25W
50/60
50/60
100/100
200/200
0.6/0.6
0.7/0.7
0.4/0.4
0.4/0.4
750~1350/1000~1650
550~1400/650~1650
850~1350/1000~1650
600~1350/800~1650
8
8
2
2
12
15
12
15
E
LGU-12 -3~120-S25LGU-12 -3~120-S25WLGP-12 -3~120-S25LGP-12 -3~120-S25W
Fig.D-53
〔Round Weight 2kg〕
LGU-15 -160~360-S25LGU-15 -160~360-S25WLGP-15 -160~360-S25LGP-15 -160~360-S25W
Fig.D-54
〔Round Weight 2.5kg〕
FGU-12 -3~120-S25FGU-12 -3~120-S25WFGP-12 -3~120-S25FGP-12 -3~120-S25W
Fig.D-55
〔Round Weight 2kg〕
FGU-15 -160~360-S25FGU-15 -160~360-S25WFGP-15 -160~360-S25FGP-15 -160~360-S25W
Fig.D-56
〔Round Weight 2.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 25W
12
15
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
P.D45 Fig.D-53 2kg
P.D45 Fig.D-55 2kg
P.D43 Fig.D-57 2.5kg
P.D43 Fig.D-59 2.5kg
P.D45 Fig.D-54 2.5kg
P.D45 Fig.D-56 2.5kg
P.D43 Fig.D-58 3kg
P.D43 Fig.D-60 3kg
50Hz 60Hz50rpm (%)
1/300
1/360
5
4.2
6
5
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
2.7
2.7
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
25.5
25.5
*
*
■Frame No.12/100V ■Frame No.12/200V ■Frame No.15/100V ■Frame No.15/200V
LGU-12M-S25 LGU-12M-S25W LGP-12M-S25 LGP-12M-S25W
CAD Data: LGU-15M-S25 LGU-15M-S25W LGP-15M-S25 LGP-15M-S25W
CAD Data:
FGU-15M-S25 FGU-15M-S25W FGP-15M-S25 FGP-15M-S25W
CAD Data:
FGU-12M-S25 FGU-12M-S25W FGP-12M-S25 FGP-12M-S25W
CAD Data:
MBMBMBMB
MBMBMBMB
MBMBMBMB
MBMBMBMB
kgf・mN・mkgfN
50(100V)
60(100V) (200V)
75(100V) (200V)
45(200V)
300 2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
163.8300
4-φ6.5
5
17 65
90104
97.5
171.82522
13
8
374056
90.5
φ15h7
300
300300
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
163.8300
4-φ6.5
φ15h7
90.5
2522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
171.8
500 1000 1500
200
150
100
50
0
50Hz60Hz
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W
Speed control gearmotorsSpeed control brake motors
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
1-Phase 25W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕 Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series
Torque〔
%〕
Torque〔
%〕
Torque〔
%〕
Torque〔
%〕
D45D44
Foot Mount Type Speed control gearmotor
Flange Mount Type Speed control gearmotor
25W
S25
S25W
50/60
50/60
100/100
200/200
0.6/0.6
0.7/0.7
0.4/0.4
0.4/0.4
750~1350/1000~1650
550~1400/650~1650
850~1350/1000~1650
600~1350/800~1650
8
8
2
2
12
15
12
15
E
LGU-12 -3~120-S25LGU-12 -3~120-S25WLGP-12 -3~120-S25LGP-12 -3~120-S25W
Fig.D-53
〔Round Weight 2kg〕
LGU-15 -160~360-S25LGU-15 -160~360-S25WLGP-15 -160~360-S25LGP-15 -160~360-S25W
Fig.D-54
〔Round Weight 2.5kg〕
FGU-12 -3~120-S25FGU-12 -3~120-S25WFGP-12 -3~120-S25FGP-12 -3~120-S25W
Fig.D-55
〔Round Weight 2kg〕
FGU-15 -160~360-S25FGU-15 -160~360-S25WFGP-15 -160~360-S25FGP-15 -160~360-S25W
Fig.D-56
〔Round Weight 2.5kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 25W
12
15
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
1/200
1/240
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
7.5
6.3
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
9
7.5
10
20
30
35
40
45
50
50
50
50
50
50
50
70
70
70
0.03
0.06
0.11
0.17
0.23
0.28
0.34
0.45
0.56
0.68
0.86
1.1
1.3
1.7
2.1
2.6
P.D45 Fig.D-53 2kg
P.D45 Fig.D-55 2kg
P.D43 Fig.D-57 2.5kg
P.D43 Fig.D-59 2.5kg
P.D45 Fig.D-54 2.5kg
P.D45 Fig.D-56 2.5kg
P.D43 Fig.D-58 3kg
P.D43 Fig.D-60 3kg
50Hz 60Hz50rpm (%)
1/300
1/360
5
4.2
6
5
70
70
98
196
294
343
392
441
490
490
490
490
490
490
490
686
686
686
686
686
2.7
2.7
0.29
0.59
1.08
1.67
2.25
2.74
3.33
4.41
5.49
6.66
8.43
10.8
12.7
16.7
20.6
25.5
25.5
25.5
*
*
■Frame No.12/100V ■Frame No.12/200V ■Frame No.15/100V ■Frame No.15/200V
LGU-12M-S25 LGU-12M-S25W LGP-12M-S25 LGP-12M-S25W
CAD Data: LGU-15M-S25 LGU-15M-S25W LGP-15M-S25 LGP-15M-S25W
CAD Data:
FGU-15M-S25 FGU-15M-S25W FGP-15M-S25 FGP-15M-S25W
CAD Data:
FGU-12M-S25 FGU-12M-S25W FGP-12M-S25 FGP-12M-S25W
CAD Data:
MBMBMBMB
MBMBMBMB
MBMBMBMB
MBMBMBMB
kgf・mN・mkgfN
50(100V)
60(100V) (200V)
75(100V) (200V)
45(200V)
300 2220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
163.8300
4-φ6.5
5
17 65
90104
97.5
171.82522
13
8
374056
90.5
φ15h7
300
300300
2220
76.5
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35)
163.8300
4-φ6.5
φ15h7
90.5
2522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
171.8
500 1000 1500
200
150
100
50
0
50Hz60Hz
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W
Speed control gearmotorsSpeed control brake motors
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
1-Phase 25W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕 Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series
Torque〔
%〕
Torque〔
%〕
Torque〔
%〕
Torque〔
%〕
D47D46
Foot Mount Type Speed control gearmotor with Brake
Flange Mount Type Speed control gearmotor with Brake
LGPN-12 -3~120-S25LGPN-12 -3~120-S25WFig.D-57
〔Round Weight 2.5kg〕
LGPN-15 -160~360-S25LGPN-15 -160~360-S25WFig.D-58
〔Round Weight 3kg〕
FGPN-12 -3~120-S25FGPN-12 -3~120-S25WFig.D-59
〔Round Weight 2.5kg〕
FGPN-15 -160~360-S25FGPN-15 -160~360-S25WFig.D-60
〔Round Weight 3kg〕
CAD Data: LGPN-12M-S25 LGPN-12M-S25W CAD Data: LGPN-15M-S25 LGPN-15M-S25W
CAD Data: FGPN-12M-S25 FGPN-12M-S25W CAD Data: FGPN-15M-S25 FGPN-15M-S25W
MBMB
MBMB
MBMB
MBMB
3003002220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
198.3300
4-φ6.5
5
17 65
90104
97.5
206.32522
13
8
374056
90.5
φ15h7
300300
300198.3
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300300
4-φ6.5
φ15h7
90.5
206.32522
13
9 3
29
525
17
38 3891
9151
(φ40) 300300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W
Speed control gearmotorsSpeed control brake motors
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
GTR-L Series
D47D46
Foot Mount Type Speed control gearmotor with Brake
Flange Mounted Type Speed control gearmotor with Brake
LGPN-12 -3~120-S25LGPN-12 -3~120-S25WFig.D-57
〔Round Weight 2.5kg〕
LGPN-15 -160~360-S25LGPN-15 -160~360-S25WFig.D-58
〔Round Weight 3kg〕
FGPN-12 -3~120-S25FGPN-12 -3~120-S25WFig.D-59
〔Round Weight 2.5kg〕
FGPN-15 -160~360-S25FGPN-15 -160~360-S25WFig.D-60
〔Round Weight 3kg〕
CAD Data: LGPN-12M-S25 LGPN-12M-S25W CAD Data: LGPN-15M-S25 LGPN-15M-S25W
CAD Data: FGPN-12M-S25 FGPN-12M-S25W CAD Data: FGPN-15M-S25 FGPN-15M-S25W
MBMB
MBMB
MBMB
MBMB
3003002220
7
33.535
76.5
50
φ12h7
4-φ6.5 9076
13.5
4
5582.5
11
300
198.3300
4-φ6.5
5
17 65
90104
97.5
206.32522
13
8
374056
90.5
φ15h7
300300
300198.3
2220
φ12h7
4-φ6.5
411
8 3
26
21
13.5
32 3277
4377
(φ35) 300
76.5
300300
4-φ6.5
φ15h7
90.5
206.32522
13
9 3
29
525
17
38 3891
9151
(φ40) 300300
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 25W
Speed control gearmotorsSpeed control brake motors
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
GTR-L Series
D49D48
40W
S40
S40W
50/60
50/60
100/100
200/200
0.9/0.9
0.5/0.5
800~1350/1050~1650
900~1350/1300~1650
12
3
15
15
E
LGU-15 -3~360-S40LGU-15 -3~360-S40WLGP-15 -3~360-S40LGP-15 -3~360-S40W
Fig.D-61
〔Round Weight 3kg〕
LGU-15M-S40 LGU-15M-S40W LGP-15M-S40 LGP-15M-S40W
FGU-15 -3~360-S40FGU-15 -3~360-S40WFGP-15 -3~360-S40FGP-15 -3~360-S40W
Fig.D-62
〔Round Weight 3kg〕
LGPN-15 -3~360-S40LGPN-15 -3~360-S40WFig.D-63
〔Round Weight 3kg〕
FGPN-15 -3~360-S40FGPN-15 -3~360-S40WFig.D-64
〔Round Weight 3kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 40W
15
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
15
30
35
45
50
55
65
70
70
70
70
70
70
70
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
P.D49 Fig.D-61 3kg
P.D49 Fig.D-62 3kg
P.D49 Fig.D-63 3kg
P.D49 Fig.D-64 3kg
50Hz 60Hz50rpm (%)
1/200
1/240
1/300
1/360
7.5
6.3
5
4.2
9
7.5
6
5
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
*
*
*
*
■100V ■200V
CAD Data:
FGU-15M-S40 FGU-15M-S40W FGP-15M-S40 FGP-15M-S40W
CAD Data:
CAD Data: LGPN-15M-S40 LGPN-15M-S40W CAD Data: FGPN-15M-S40 FGPN-15M-S40W
MBMBMBMB
MBMBMBMB
MBMB
MBMB
kgf・mN・mkgfN
50(100V) (200V)
40(100V) (200V)
75(100V) (200V)
300
4-φ6.5
5
17 65
90104
97.5
171.82522
13
8
374056
90.5
φ15h7
300
300
4-φ6.5
φ15h7
90.5
2522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
171.8
300
4-φ6.5
5
17 65
90104
97.5
206.32522
13
8
374056
90.5
φ15h7
300300
300
4-φ6.5
φ15h7
90.5
206.32522
13
9 3
29
525
17
38 3891
9151
(φ40) 300300
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 40W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mounted Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mounted Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-type
1-Phase 40W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series
D49D48
40W
S40
S40W
50/60
50/60
100/100
200/200
0.9/0.9
0.5/0.5
800~1350/1050~1650
900~1350/1300~1650
12
3
15
15
E
LGU-15 -3~360-S40LGU-15 -3~360-S40WLGP-15 -3~360-S40LGP-15 -3~360-S40W
Fig.D-61
〔Round Weight 3kg〕
LGU-15M-S40 LGU-15M-S40W LGP-15M-S40 LGP-15M-S40W
FGU-15 -3~360-S40FGU-15 -3~360-S40WFGP-15 -3~360-S40FGP-15 -3~360-S40W
Fig.D-62
〔Round Weight 3kg〕
LGPN-15 -3~360-S40LGPN-15 -3~360-S40WFig.D-63
〔Round Weight 3kg〕
FGPN-15 -3~360-S40FGPN-15 -3~360-S40WFig.D-64
〔Round Weight 3kg〕
LGU・LGP FGU・FGP LGPN FGPN
1-phase 40W
15
1/ 3
1/ 5
1/ 10
1/ 15
1/ 20
1/ 25
1/ 30
1/ 40
1/ 50
1/ 60
1/ 80
1/100
1/120
1/160
500
300
150
100
75
60
50
37.5
30
25
18.8
15
12.5
9.4
600
360
180
120
90
72
60
45
36
30
22.5
18
15
11.2
15
30
35
45
50
55
65
70
70
70
70
70
70
70
0.05
0.09
0.18
0.27
0.36
0.45
0.54
0.72
0.90
1.1
1.4
1.7
2.1
2.7
P.D49 Fig.D-61 3kg
P.D49 Fig.D-62 3kg
P.D49 Fig.D-63 3kg
P.D49 Fig.D-64 3kg
50Hz 60Hz50rpm (%)
1/200
1/240
1/300
1/360
7.5
6.3
5
4.2
9
7.5
6
5
70
70
70
70
147
294
343
441
490
539
637
686
686
686
686
686
686
686
686
686
686
686
2.7
2.7
2.7
2.7
0.49
0.88
1.76
2.65
3.53
4.41
5.29
7.06
8.82
10.8
13.7
16.7
20.6
26.5
26.5
26.5
26.5
26.5
*
*
*
*
■100V ■200V
CAD Data:
FGU-15M-S40 FGU-15M-S40W FGP-15M-S40 FGP-15M-S40W
CAD Data:
CAD Data: LGPN-15M-S40 LGPN-15M-S40W CAD Data: FGPN-15M-S40 FGPN-15M-S40W
MBMBMBMB
MBMBMBMB
MBMB
MBMB
kgf・mN・mkgfN
50(100V) (200V)
40(100V) (200V)
75(100V) (200V)
300
4-φ6.5
5
17 65
90104
97.5
171.82522
13
8
374056
90.5
φ15h7
300
300
4-φ6.5
φ15h7
90.5
2522
13
9 3
29
525
17
38 3891
9151
(φ40) 300
171.8
300
4-φ6.5
5
17 65
90104
97.5
206.32522
13
8
374056
90.5
φ15h7
300300
300
4-φ6.5
φ15h7
90.5
206.32522
13
9 3
29
525
17
38 3891
9151
(φ40) 300300
50Hz60Hz
500 1000 1500
200
150
100
50
0
50Hz60Hz
500 1000 1500
200
150
100
50
0
Note) Since the figure in the parenthesis is the one with black scale, add more than 0.5mm to that figure for the diameter of the connecting hole. In the CAD data, the file name is common to the both type, M(Metal type) and B(Bearing type).
Note) The allowable O.H.L indicated are the values in the central position of the output shaft. The models marked with * are low troque type. Be sure to refer to the allowable torque rating in the performance table. Be sure to read the cautions stated on Page D9.
Model Code P.D34
Option P.E110~E112P.E54
Lead-Wire/Terminal Box Position Mark
G-Type〔Parallel Shaft〕 1-Phase 40W
Speed control gearmotorsSpeed control brake motors
Foot Mount Type Speed control gearmotor with Brake Flange Mount Type Speed control gearmotor with Brake
Foot Mount Type Speed control gearmotor Flange Mount Type Speed control gearmotor
Performance Table/ Dimension
Performance Table/ Dimension
Foot Mount type Flange Mount type
Standard Voltage (Continuous Rated 4 Poles)
Double Voltage (Continuous Rated 4 Poles)
Motor Specs. CapacityMotor Capacity Designation
Frequency (Hz)
Capacitor (μF)
Voltage (V)
MAX Current (A)
High speed rotation range (rpm)
Insulation Classification
Protective system
Frame No.
Totally Enclosed
high speed Motor Capacity
Reduction Ratio
Frame No.
Output Shaft Rotation Speed (rpm)
Output Shaft Allowable TorqueOutput Shaft Allowable O.H.L
Page, Diagram No. of the Outer Dimension Diagram, Round Weight
Gearmotor Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Speed Control Gearmotor
Standard Motors
Cautions for Safety
Option
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
Water- resistant Gearmotor with Brake
Parallel Shaft Performance Table/ Dimension
Right Angle Shaft Performance Table/ Dimension
Concentric Hollow Shaft Concentric Solid Shaft Performance Table/ Dimension
Technical Information
Gearmotor with Brake
Gearmotor with Brake
GT-Type Gearmotor with Brake
Gearmotor with Brake
Gearmotor with Clutch /Brake
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor
Speed Control Gearmotor with Brake
Standard Motors
Cautions for Safety
Option
Water- resistant Gearmotor with Brake
With Water- resistant Brake Motor
With Water- resistant Brake Motor
Parallel Shaft GTR-L Series Performance Table/ Dimension
Reversible Gearmotor with Brake
As for motor-type:"U-Type" and "P-Type" are available in the Speed Control Gearmotor. Dimensions shown in the dimension diagram are all that for the "P-Type". In case of "U-Type", the only difference is the part of lead wire which has a connector as shown in the right.
U-Type Lead wire with connector 150mmMotor lead wire 300mm Lead wire for generator 300mm (white・white)
P-Type
1-Phase 40W
Torque-Rotation Speed Characteristic Graph Note) 100% torque shows the allowable torque at high speed.
Torque〔
%〕
Torque〔
%〕
Rotation Speed〔rpm〕 Rotation Speed〔rpm〕
GTR-L Series