standard chairs

8/6/2019 Standard Chairs

1/19

Page 1

PROPOSED INTERIOR FOR SBI-THOUSAND LIGHTS BRANCH, CHENNAI

BILL OF QUANTITIES

INTERIOR WORKS

a

b

c

d

e

f

g

All concealed faces of ply and country wood tobe painted with one coat of wood preservativepaint.

Table Drawer and cupboard inside should befinished with 1mm thick laminate.

All exposed faces of Steam Beach beading /lipping should be melamine polished and tintedto required shade as directed by the Bank.

All com.ply free edges should be provided withTW lipping alround.

Size of framework indicated should be finishedsize.

Cost should include for providing grooves inlaminate as shown in drg. and TW beadingswherever shown should be included.

Termite treatment shall be done for all wooden

and ply members.


2/19

Page 2


3/19

Page 3

S.No. Description Qty Unit Rate mount in INR

1

5 sqm 3500.00 17500.00

0.00

2

0.00

0.00

0.00

0.00

0.00

0.00

0.00

Providing and fixing low level partition of1200mm height as per drg. comprising:

Salwood frame work of 50 x 50mm at about 600mm centres vertically and 3 nos. horizontally ofthe same section at floor level, 750mm leveland at 1200mm level. 50 x 25mm at 375 mm

level all framed and fixed in position, 8 mm comply finished with 1mm Laminate with grooveson both sides of approved colour and shade.

Top of the partition finished with 15 mm thickand 75mm wide Steam beach moulding andpolished with melamine. A soft board of 12 mmthick to be fixed over the partiton above900mm height of required shape as shown inthe drg, fabric cost not less than Rs 150 / m.8mm thick clear float glass with etching is fixedover the partition as shown in drawing. Alroundthe partition 75mm thick Dark colour laminateis provided as show in the drawing and pattern.

All concealed faces of com.ply and frame workfinished with one coat of wood preservativepaint and exposed faces of Steam beachbeading polished to the satisfaction of the Bank.

Providing and fixing double skin full heightpartition to detail as per drg. of job no.comprising:

(a) Frame work:salwood frames of 50 x 50,

vertically at about 60 cm centres varied alongcolumns wall ends, junctions of walls, asnecessary and as shown in drg., horizontally ofsame size at floor level, 75 cm, 150 cm, 210cm , and roof level, 50 x 25 mm and at 35 cmlevel, fixed in position, the vertical frames fixedto soffit of slab, with necessary screws, MSclamps, rawl plugs, expansion fasteners etc.,complete.

(b) Lining with 8 mm com.ply on both sides offramework from floor level to flase ceiling level,and finished with 1 mm laminate of approvedcolour and shade on both sides includingnecessary grooves, Steam beach beadings .Thealternate frame fixed to soffit of slab withnecessary arrangements.

All concealed faces of comply and frame workfinished with one coat of wood preservativepaint and exposed faces of Steam beachbeading melamine polished to the satisfactionof the Architects.


4/19

Page 4

S.No. Description Qty Unit Rate mount in INR0.00

25 sqm 3100.00 77500.00

0.00

0.00

3

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

19 sqm 3300.00 62700.00

0.00

0.00

0.00

Measurement for the partition area shall beconsidered from floor level to false ceiling levelonly.

Note :In Door area concealed 50 x 50mmSecond class TW frame to be provided.

Providing and fixing double skin partition,partly panelled and partly glazed to detail asper drg. No. of job no. comprising:

(a) Frame work:salwood frames of 50 x 50,vertically at about 60 cm centres varied alongcolumns wall ends, junctions of walls, asnecessary and as shown in drg., horizontally ofsame size at floor level, 75 cm, 210 cm , androof level, 50 x 25 mm and at 35 cm level,fixed in position, the vertical frames fixed tosoffit of slab, with necessary screws, MSclamps, rawl plugs, expansion fasteners etc.,complete.

(b) Lining with 8 mm com.ply on both sides offramework from floor level to 90 cm level and210 cm level to false ceiling level finished with1 mm laminate of approved colour and shade.Between 90 cm and 210 cm levels. 8 mm thickclear float glass with etching fixed over Steambeach beading of size 40 x 15 mm all around inpanels.

All concealed faces of comply and frame workfinished with one coat of wood preservativepaint and exposed faces of Steam beachbeading melamine polished to the satisfactionof the Architects.

Measurement for the partition area shall beconsidered from floor level to false ceiling level

Note :In Door area concealed 50 x 50mm

Second class TW frame to be provided.


5/19

Page 5


4

6 sqm 8500.00 51000.00

0.00

5

6 sqm 7000.00 42000.00

0.00

6

6 sqm 6500.00 39000.00

0.00

7

4 sqm 7000.00 28000.00

8

0.00

Providing and fixing Fully glazed main entrancedoor to detail as per drawing no.---- of job no..with Steam beach wood frame of size 100 x 60mm with 150 x 40 mm thick styles for top,bottom, and two vertical style, Double leafglazed shutters of 12 mm thick clear float glasswith etching fixed with necessary steam beachbeadings. All frames and shutters to be finished

with Melamine polish and 600mm high stainlesssteel brush finish handle to shape to be fixedon both side . All necessary brass hardwarefittings,DORMA MAKE floor springs, lockingarrangements etc., fixed to the shutters. Allframes and shutters to be finished withMelamine polish.

Providing and fixing partly panelled and partlyglazed door as per drg. no. ----- of job no. -------in partition with concealed frame work ofsecond class TW of size 50 x 50 mm to detail

with shutter styles of 35mm thick (finished)flush shutter finished with 1mm laminate and8mm thick clear float glass with etching asshown in drg. All necessary brass hardwarefittings, DORMA MAKE locking arrangements,300mm high SS brush finish handles, doorcloser etc. fixed to the shutters.

Providing and fixing Flush door as per drg.todetail, 35mm thick (finished) flush shutters insingle leaf with external lipping and phenolformaldehyde bonding and finished with 1mmlaminate of approved color and shade. Includingnecessary hardware fitting, DORMA MAKElocking arrangements, 300mm high SS brushfinish handles, door closer etc. fixed to the

Providing and fixing Flush door with frame ofsize 75 x 60mm finished with 2 coats of enamelpaint over a coat of primer as per drg.to detail,35mm thick (finished) flush shutters in singleleaf with external lipping and phenolformaldehyde bonding and finished with 1mmthick laminate of approved shade. Includingnecessary brass hardware fittings, lockingarrangements, 300mm high SS brush finishhandles, door closer etc., fixed to the shutters.

Providing and fixing in position M / Fsuspended false ceiling to detailas per drg. No.of Job No. with GI frame work and 12.5 mmtapered type gyp board panels to form grids of45.7 x 122 cm as per manufacturersspecification including provision for steppedshaped ceiling for light trough comprising.


6/19

Page 6


0.00

0.00

0.00

0.00

140 sqm 700.00 98000.00

0.00

9

0.00

0.00

42 sqm 950.00 39900.00

0.00

Frame work of intermediate channels (M.F.T.) at122 cm centres along one direction M/F ceilingsection MF5 at 45.7 cm centres along otherdirection. Perimeter channels (MF 6A) alongwalls alround perimeter side of the ceiling, all todetail as per drg.

The intermediate channels suspended fromceiling, through strap hangers 25 x 0.5 mm (MF8) at 122 cm centres connected to soffit cleatsP534 (27 x 37 x 25 x 1.6mm) the cleatsconnected to ceiling through metal expansionrawl plugs 1/2" dia and 17/16" long withnecessary bolts and nuts etc. all connected withadditional perimeter channels (MF 6A) foropenings for light fixtures, AC ducts, verticaldrops, offsets etc. wherever necessary all to

12.5 mm thick gyp board with tapered edges

fixed to underside of suspended grid with 25mm screws to form grids of 45.7 cm x 122 cmvaried along wall ends etc. includingArchitectural boxing,moulding and painting theunderside of gyp board with 2 coats of plasticemulsion paint over a priming coat etc.complete. ( The false ceiling area will bemeasured in flat area .)

Providing and fixing in true horizontal level falseceiling as per drg. of Job no. with ceiling grid ofSUPRAFINE XL 15 mm system manufactured by

approved agencies,using hot dipped galvanizedsteel section exposed surface chemicallycleaned capping prefinished in baked polyesterpaint wall angle of size 3000 x 19 x 19mm usedin the periphery of the ceiling fixed to the wallpartition RC column band walls with the help ofscrews at 600mm C/C.

600mm long cross tee of size 15 x 32 mm fixedin between 1200 mm long cross tee for forminga grid of 600 x 600 mm. Finally laying 595 x

595 x 9.5mm thick Coloured GYPREX TILE withapproved finish of INDIA GYPSUM


7/19

Page 7


10

4.00 sqm. 1500.00 6000.00

11

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

Providing and fixing ply box false ceiling with12mm com ply finished with 1mm laminate ofapproved colour and shade. The frame workcomprising of main grid 50 x 35mm secondclass TW at 450mm centre to centre both waysand the grid to be suspended by 8 gauge GIwire from roof slab by anchor fasteners to theslab and level adjuster clip GI wire.

All concealed faces of comply finished with onecoat of wood preservative paint.

Providing and fixing Branch Manager table ofsize 1800 x 750mm to detail as shown in drg.no. of Job No. to shape and 0.75 m highcomprising table top out of 18 mm. Comply withstiffner of same comply 100 mm wide below thetable and 10 x 37 mm. Steam Beach moulding

to shape along edges.

Table top finished with 1mm laminate ofapproved colour and shade on front and side ofdrawer, finished with 1mm thk laminate andadditional 18mm comply is fixed on front side topattern with necessary grooves as shown in thedrg., and finished with 1mm thk, laminate ofapproved shade.The table is supported at front,sides and drawers with 18 mm comply andfinished with 1 mm laminate of approved colourand shade.

Foot rest of required length with same 18 mm.Comply as shown in drg.

MS Powder coated Telescopic Keyboard trayand MS wire manager of 50mm dia of approvedualit .

One set of 4 drawers about 40cm wide, 71.25cm high and 60cm deep to shape supportedwith 18 mm comply at bottom, sides and rear.Drawers 4 nos. of which 3 nos. of equal height

and 1 no. drawer at the top most of 7.5 cm highmade out of 12 mm thick comply for sides, rear,bottom and face of drawer with 18mm complywith necessary TW lipping, Telescopic drawerslides, locking arrangement, 100 mm long ssBrush finish handles, etc. complete.

Front face of the drawer finished with 1mmthick laminate of approved shade and colourwith TW lipping on the edge of drawer.


8/19

Page 8


1 no 20000.00 20000.00

0.0012

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

All concealed faces of comply finished with onecoat of wood preservative paint and exposedfaces of Steam beach beading polished to thesatisfaction of the Bank. The inside faces ofdrawer should be finished with 1mm thicklaminate

Providing and fixing Officer table of size 1650 x750mm to detail as shown in drg. no. of Job No.to shape and 0.75 m high comprising table topout of 18 mm. Comply with stiffner of samecomply 100 mm wide below the table and 10 x37 mm. Steam Beach moulding to shape alongedges.

Table top finished with 1mm laminate ofapproved colour and shade on front and side ofdrawer, finished with 1mm thk laminate andadditional 18mm comply is fixed on front side topattern with necessary grooves as shown in thedrg., and finished with 1mm thk, laminate ofapproved shade.The table is supported at front,sides and drawers with 18 mm comply andfinished with 1 mm laminate of approved colourand shade.

Foot rest of required length with same 18 mm.Comply as shown in drg.

MS Powder coated Telescopic Keyboard trayand MS wire manager of 50mm dia of approved

One set of 4 drawers about 40cm wide, 71.25cm high and 60cm deep to shape supportedwith 18 mm comply at bottom, sides and rear.Drawers 4 nos. of which 3 nos. of equal heightand 1 no. drawer at the top most of 7.5 cm highmade out of 12 mm thick comply for sides, rear,bottom and face of drawer with 18mm complywith necessary TW lipping, Telescopic drawerslides, locking arrangement, 100 mm long ssBrush finish handles, etc. complete.

Front face of the drawer finished with 1mmthick laminate of approved shade and colourwith TW lipping on the edge of drawer.


9/19

Page 9


2 nos 20000.00 40000.00

0.00

All concealed faces of comply finished with onecoat of wood preservative paint and exposedfaces of Steam beach beading polished to thesatisfaction of the Bank. The inside faces ofdrawer should be finished with 1mm thicklaminate


10/19

Page 10


13

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

7 Rm 7500.00 52500.00

0.00

14

0.00

Providing and fixing running table with drawerunit to detail. Continuous table top of 18mmthick com ply with stiffner for 100mm widealround and 10 x 37 mm Steam beach mouldingalong edges and top finished with 1mmlaminate of approved colour and shade. Tablesupports made out of 18mm comply at every1250mm centre to centre (approximate) and

600mm wide and 750mm high finished with1mm laminate of approved colour and shade.

Foot rest of required length with same 18mmcomply.

MS Powder coated Telescopic Keyboard tray(2nos) and MS powder coated wire manager(2nos) 50mm dia of approved quality .

Two set of 3 drawers about 400 mm width,712.5 mm height and 600 mm deep supportedwith 18 mm com ply at bottom, sides and rear.Drawers 3 nos. of which 2 nos. of equal heightand 1 no. drawer at the bottom of 230 mmheight made out of 12 mm thick com ply forsides, rear, bottom and face of drawer with 18mm com ply and finished with 1mm thicklaminate of approved colour, with necessarylipping, telescopic drawer slides, lockingarrangement, 100 mm long brush finish S.S.handles, etc. complete.

All concealed faces of comply finished with onecoat of wood preservative paint and exposedfaces of steam beach beading polished to thesatisfaction of the Bank. The inside faces ofdrawer should be finished with 1mm thicklaminate.

Providing and fixing Grahamithra table to shapeas per drawing of overall size about 1800 mmand 750 mm height comprising table top at twolevels as shown made of 18 mm thick com ply

and stiffner of 18 mm thick comply for 100 mmwidth, finished with 1 mm thick laminate ofapproved colour including 10 x 37mm Steambeach moulding.In front of the table, at1050mm level 150mm wide writing top isprovided with 18mm com ply finished with 1mmlaminate of approved shade and colour.


11/19

Page 11


0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

1 no 16000.00 16000.00

0.00

15

0.00

0.00

0.00

Table top finished with 1mm laminate ofapproved colour and shade on front and side ofdrawer, finished with 1mm thk laminate andadditional 10mm comply is fixed on front side topattern as shown in the drg., and finished with1mm thk, laminate of approved shade. 12mmthick clear float glass is fixed in the middle of

the additional ply area with SS Studs. The tableis supported at front, sides and drawers with 18mm comply and finished with 1 mm laminate ofapproved colour and shade.

One set of 3 drawers about 400 mm width,712.5 mm height and 600 mm deep supportedwith 18 mm com ply at bottom, sides and rear.Drawers 3 nos. of which 2 nos. of equal heightand 1 no. drawer at the bottom of 230 mmheight made out of 12 mm thick com ply forsides, rear, bottom and face of drawer with 18

mm com ply and finished with 1 mm thicklaminate of approved colour, with necessarylipping, telescopic drawer slides, lockingarrangement, 100 mm long brush finish S.S.handles, etc. complete.

Foot rest of required length with18mm thickcom ply to shape.

MS Powder coated Telescopic Keyboard trayand MS wire manager of 50mm dia of approved

quality .

All concealed faces of comply finished with onecoat of wood preservative paint and exposedfaces of Steam beach beading polished to thesatisfaction of the Bank. The inside faces ofdrawer finished with 1mm thick laminate.

Providing and fixing Single window systemwithout partitions as shown in drg. of eachcounter size about 1650 mm length and 2100mm depth comprising

Counter and writing top at front, with counter1500 mm width and 875 mm depth at about750 mm level made out of 18mm com plyfinished with 1mm laminate and 10 x37mmSteam beach moulding on the edges. 18 mmcom ply for sides and for front shaped supportand finished with 1 mm thick laminate ofa roved colour.


12/19

Page 12


0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

6 nos 35000.00 210000.00

0.00

Front counter support for 750 mm height with18 mm com ply finished with 1 mm laminate ofapproved colour and shade . Below countertop .Additional 18mm com ply finished with1mm laminate is fixed to pattern as shown.

12 mm thick clear float glass to shape withetching is fixed with Steam beach beadingfixed at front above the counter.

The sides of the counter, boxing on either sideto shape as shown in the drawing with 18 mmcom ply and to be finished with 1 mm thicklaminate of approved colour from floor level to1175 mm level at places shown in the drg. Topof the boxing finishing with 20mm thick RoyalRed Granite with edge moulding alround.

One set of 3 drawers about 450 mm width,712.5 mm height and 600 mm deep supportedwith 18 mm com ply at bottom, sides and rear.Drawers 3 nos. of which 2 nos. of equal heightand 1 no. drawer at the bottom of 230 mmheight made out of 12 mm thick com ply forsides, rear, bottom and face of drawer with 18mm com ply and finished with 1mm thicklaminate of approved colour, with necessarylipping, telescopic drawer slides, lockingarrangement, 100 mm long brush finish S.S.handles, etc. complete. Top most cash draw

should be arranged with provisional fordenomination with 12mm thk comply.

MS Powder coated Teloscopic keyboard tray andMS wire manager of 50mm dia of approvedualit .

Foot rest of required length with18mm thickcom ply to shape as shown in the drawing.

All concealed faces of comply finished with onecoat of wood preservative paint and exposed

faces of Steam beach beading polished to thesatisfaction of the Architects. The inner side ofthe unit finished with 1mm Laminate.

The rate should include automatic locks, MSpowder coated key board trays, Telescopicdrawer slides, 100mm SS brush finish handlewith necessary hardware fittings etc., complete.


13/19


14/19

Page 14


1 nos 8000.00 8000.00

0.00

18

0.00

0.00

0.00

0.00

2 nos 8000.00 16000.000.00

19

9 sqm 5500.00 49500.00

0.00

20

0.00

0.00


Providing and fixing side unit for table to detail

as per drg. no. of job no. of size 1000 x 450mm18 mm comply for top, bottom, rear and sides,one intermediate of same comply with astiffner of same ply 100mm wide below the topand 10x37mm Steam Beach moulding along theedges, with necessary TW lipping and side hungshutter in both the panels using 18 mm complyand finished with 1mm laminate and in thecentre for 100mm wide 1mm laminate ofapproved colour is shown to the pattern shownin the drg., andmelamine polished of approvedshade, including all necessary Box Type hinges,locks, 100 mm long S.S brush finish handles

etc,.complete.

The top surface of unit finished with 1 mmlaminate of approved colur and shade.


Providing and fixing full height storage unit withshutter of size 2150 mm high and 600 mm deepto detail comprising 18mm thick com ply for topand sides and 4 intermediates and bottom at75mm level. 18mm thick com ply for side hungshutters. The required leaves finished with1mm laminate including necessary, grooves topattern TW lipping, box type hinges, towerbolts, locking arrangements, handle (aluminiumpowder coated) 150 mm long SS Brush Finishhandle etc., complete as shown in the drawing.

Providing and fixing low level storage to detailof drg.No. of Job No. about 45 cm wide and 75cm high comprising.


15/19

Page 15


0.00

0.00

0.00

0.00

0.00

0.00

8 Rm 8000.00 64000.00

0.00

21

35 sqm 1000.00 35000.00

0.00

22

150 sqm 150.00 22500.00

0.00

23

1 nos 4000.00 4000.00

0.00

18 mm thick comply fixed at top and bottom at7.5 cm level, sides at not more than 90 cmcentres and one intermediate horizontal boardwith necessary TW reepers, 18mm com.ply forrear, and 10x37mm steam Beach moulding,along the edges.

Side hung shutters in 2 leaves with 18 mm thickcomply and on top finished with 1mm laminateof approved colour and shade in the centreportion for 100mm wide dark colour veneerstrip is shown to desigh and pattern as of drg.,including necessary grooves,Box type hinges,locking arrangements, 100 mm long S.S brushfinish handles etc. complete.

Finish: Exposed faces of comply at top andsides of unit, finished with 1mm laminate ofapproved colour and shade.

All concealed faces of comply finished with onecoat of wood preservative paint and exposedfaces of Steam beach beading polished to thesatisfaction of the Bank. The inside faces ofdrawer finished with 1mm thick laminate

Providing and fixing 100mm wide vertical blindsof approved make quality and colour shade andpattern. Rate shall include necessary scotchguard treatment on both side. The overlaps

should be uniform and adequate.

Prepare surface and paint two coats of Plasticemulsion paint of approved colour and shadeover a coat of primer including Alteck puttyafter thoroughly scrapping the existing internalwalls.

Providing and fixing writing table of overall sizeabout 1500mm long and 230 mm to 350 mmwidth to shape as shown in drawing at about105cm from floor level, comprising 12mm clearfloat glass with edge polished at top and bottomand verticals of same glass with edge polishedand 18mm comply backing at wall end asshown in drawing.


16/19

Page 16


24

2 Nos. 5000.00 10000.00

0.00

25

3 sqm 3000.00 9000.00

0.00

26

10 sqm 2000.00 20000.00

0.00

27

0.00

0.00

a Two seaters 2 No 5000.00 10000.00

0.00

28 Chairs: 0.00

a High Back Chair:

Providing and fixing Centre table of 450 diacircular shape and 450mm height supported by25mm thick comply and finished with 1mmthick laminate of approved shade as shown inthe drg. Top with 12mm thick clear float glassfixed over the 25 x 25 mm TW membersupports as shown and finished with melaminepolish. For skirting dark colour 1mm thick

laminate is provided as shown in the drawing.

Providing and fixing ROLLING SHUTTER BOXINGto detail of 18 mm thick commercial ply fixed towall with necessary screws, raul plus etc.,complete and finished with 1 mm thick laminateof app. Colour and shade

Providing and fixing commercial Ply covering

to detail, 25mm thick commercial ply stiffner onhorizontal and verticals at 60cm centres bothways fixed to wall with necessary screws,aluminium cleats, rawl plugs, etc., complete.18mm comply finished with 1mm laminate ofapproved colour and shade with necessarygrooves and beading. All concealed faces ofcomply painted with one coat of woodpreservation paint before fixing.

Providing and fixing sofa set to detail as shownin drawing about 60cm wide and about 68cmhigh comprising second class TW frameworkusing 50 x 40 TW scantlings with 8mm thickcom plywood covering on all sides. Seatsfinished with spring hooked to MS plate 25mmwidth fixed to the seat frame. Both seat frameand back covered with layer of jute cloth and75mm latex rubber (2 layer for seat alone)finished with 12mm foam lining and uphosteredto shape with fabric (basic price Rs.300/m) forthe rear of the back also and the under surfaceof the seat finished with Gada cloth 8mm plybelow seat. Note: (For sofas materials likefoam, latex rubber, gadacloth, spring ,fabricetc., to be approved by the Architects and thework to be done at the site).


17/19


18/19

Page 18


b Medium Back Chair:

12 Nos. 5000.00 60000.00

c Low Back Chair (Visitors Chair) 17 Nos. 4000.00 68000.00

0.00

d Dining Chairs 2 Nos. 2500.00 5000.00

0.00

e Airport chair (3 seaters) 4 Nos. 10000.00 40000.00

0.00

29

10 sqm 2000.00 20000.00

0.00

30

12 sqm 2500.00 30000.00

31

1 no 16500.00 16500.00

0.00

32

15 sqm 3500.00 52500.00

0.00

33

7 sqm 2800 19600.00

Crome Plated base, single point lock, nettedfabric mesh type back, adjustable arms of Size558mm X 500 mm. Seat Size 482mm X 495mmwith gas lift and twin wheels castors.

Providing and fixing wall panelling to detail ofFrame work made out of made out of 50 X25mm salwood on both horizontal and verticalsat 60cm centres both ways fixed to wall withnecessary screws, aluminium cleats, rawlplugs, etc.,complete 8mm comply finished with1mm Laminate of approved colour and shade

with necessary grooves and beading. Allconcealed faces of comply painted with onecoat of wood preservation paint before fixing.

Providing and fixing cladding around thecolumns to detail as per drawing comprising18mm thick com ply stiffner on both ways ofrequired nos, covered with 18mm com ply withgrooves, beadings and finished with 1 mm thicklaminate of approved colour as shown in the

drawing. Dark colour laminate is fixed in patternas shown drawing.

Providing and Fixing Voucher sorting table ofsize 1800 X 750 mm with necessary pigeonholes and finished with 1mm thick laminate.

Providing and fixing 18mm thick com.ply pelmetfacia for A/C, and finished with necessary paintetc.

Providing and fixing in position collapsible steelgate with vertical channels 20 x 10 x 2mm andbraced with flat iron diagonals 20 x 5mm sizewith top and bottom rail of T-iron 40 x 40 x6mm with 40mm dia steel pulleys completewith bolts, nuts, locking arrangement, stoppers,handles, including applying a priming coat ofapproved steel primer and two coats ofsynthetic enamel paint of approved colour etc.,complete.


19/19


TOTAL 1,477,700.00

PARTNER,PITHAVADIAN & PARTNERS

standard chairs

Documents