ss-20 indoor sirenen en introduction the ss-20 indoor siren will go off on-site, with a loud 90db...
TRANSCRIPT
SS-20Indoor Siren
U S E R M A N U A L
EN DE ESFR PTNL IT
© 2017 smanos. All Rights Reserved. Ver: SS-20-UM-ML-V1.0 Printed in China
SS-20Indoor Siren
U S E R M A N U A L
ENEN
FCC STATEMENT1. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including
interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in stalled and used in accordance with the instructions, may casue harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--- Reorient or relocate the receiving antenna.--- Increase the separation between the equipment and receiver.--- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada NoticeThis device complies with Industry Canada licence-exempt RSS standard(s).1. Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device."
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ENEN
Introduction
The SS-20 Indoor Siren will go off on-site, with a loud 90dB siren sound, to deter any would-be intruders when a sensor of K1 system has been triggered It is smart to have 2-4 sirens strategically placed around the your home as it easily deters any intruder if they defeated one siren but still hear NOISE! Intruders DO NOT like attention.
Pairing to the K1 Hub
This Siren needs to be paired to the K1 Hub first before use. To pair the Siren, please refer to the K1 Hub’s user manual or in the K1 section of the smanos home app, press the "+" button and follow the instructions on the Accessories page to easily add your smanos SS-20 siren.
Product Overview
Back View with mounting plate & level
Tamper Switch
LED Indicator
LED IndicatorBlinks rapidly: K1 system is alarming.Blinks once per 3 seconds: Low battery, please change the batteries.
Tamper SwitchAnti-tamper protection ensures that any attempts to move the Siren off the Mounting Plate will result in an alarm, push notification and possible email if selected.
ENEN
Installation
The Siren can be placed in any location as long as it is within the range with K1 Hub
Set the K1 system to Test Mode, and then trigger the Siren by pressing the Tampering Switch on the back of the Siren.K1 Hub will sound 3 beeps to confirm that the sensor is placed within range of the hub prior to installation.
Install the Siren using either the double-sided tape or the screws with mollys included in the package.
Notice: Removing the Back Cover off the Siren will result in an alarm. You can disarm the alarm through your K1 app and then continue the installation.
Specifications
Model: SS-20Power: 3V CR123A Li-Mn battery x 4 pcsSound: 90 DecibelsFrequency: EAN 8718868403964 868MHz UPC 859756005223 915MHzWireless range: ≤ 80 m (in open area)Operating conditions: 0-50°C/32° - 122°F, humidity < 90% RH (non-condensing)Dimensions (L x W x H): 85 x 85 x 37mm/3.35" x 3.35" x 1.46"
DEDE
Einleitung
Die SS-20 Innensirene ertönt mit einem lauten Sirenenton von 90 dB, um mögliche Eindringlinge abzuschrecken, wenn ein Sensor des K1-Systems ausgelöst wurde. Es sollten 2 - 4 Sirenen strategisch in Ihrem Heim platziert werden, da Eindringlinge abgeschreckt werden, wenn sie nach dem Umgehen einer Sirene immer noch den KRACH hören! Einbrecher erregen NICHT gern Aufmerksamkeit.
Kopplung mit K1 Hub
Diese Sirene muss vor der Verwendung mit dem K1 Hub gekoppelt werden. Zur Kopplung der Sirene siehe Bedienungsanleitung des K1 oder Abschnitt K1 der smanos home App. Tippen Sie auf „+“ und folgen Sie den Anleitungen auf der Zubehörseite zum einfachen Hinzufügen Ihrer smanos SS-20 Sirene.
Produktübersicht
Rückansicht mit Montageplatte und Wasserwaage
Sabotagekontakt LED
LEDBlinkt schnell: K1-System alarmiert.Blinkt alle 3 Sekunden: Batterie schwach, bitte Batterie austauschen.
SabotagekontaktDer Sabotageschutz gewährleistet, dass ein Versuch, die Sirene von der Montageplatte zu entfernen, zu einem Alarm, einer Push-Benachrichtigung und einer E-Mail führt, sofern gewählt.
DEDE
Installation
Die Sirene kann überall installiert werden, solange sie sich innerhalb der Reichweite des K1 Hub befindet
Versetzen Sie das K1-System in den Testmodus und lösen Sie die Sirene aus, indem Sie die Sabotagetaste auf der Rückseite der Sirene drücken.Der K1 Hub lässt 3 Signaltöne zur Bestätigung erklingen, dass sich der Sensor vor der Installation innerhalb der Reichweite des Hub befindet.
Installieren Sie die Sirene entweder mit dem mitgelieferten doppelseitigen Klebeband oder den Schrauben und Dübeln.
Hinweis: Das Abnehmen der Rückabdeckung der Sirene führt zu einem Alarm. Schalten Sie den Alarm über die K1 App unscharf und setzen Sie die Installation fort.
Technische Daten
Modell: SS-20Stromversorgung: 3 V CR123A Li-Mn Batterie x 4Ton: 90 DezibelFrequenz: EAN 8718868403964 868MHzFunk-Reichweite: ≤ 80 m (im offenen Gelände)Betriebsbedingungen: 0 - 50 °C, Luftfeuchtigkeit < 90 % rL (nicht kondensierend)Abmessungen (L x B x H): 85 x 85 x 37mm
FRFR
Avis d’Industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio par un appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio d’industrie Canada.
Introduction
La sirène d’intérieur SS-20 sonnera sur site, avec un puissant niveau sonore de 90 dB, pour dissuader tout intrus potentiel. Au moment où un détecteur du système K1 se déclenche, 2 à 4 sirènes, stratégiquement et judicieusement positionnées dans l’habitation, dissuaderont facilement par un grand bruit tout intrus qui aurait désactivé l’une d’entre elles. Les intrus n’aiment PAS être dérangés.
Couplage avec la centrale K1
Cette sirène devra être d’abord couplée à la centrale d’alarme K1 avant son utilisation. Pour coupler la sirène, veuillez vous reporter au manuel de l’utilisateur de la centrale K1 ou dans la section K1 de l’application « smanos home ». Appuyez sur le bouton « + » et suivez les instructions de la page « Accessoires » pour ajouter votre sirène smanos SS-20.
Vue d’ensemble du produit
Vue arrière avec plaque de fixation et niveau
Contact anti-sabotage
Indicateur lumineux
Indicateur lumineuxClignote rapidement : le système K1 est en alarme.Clignote une fois toutes les 3 secondes : pile épuisée , veuillez remplacer la pile.
Contact anti-sabotageLa protection anti-sabotage garantit que toute tentative de retrait de la sirène de la plaque de fixation provoquera une alarme, une notification push et éventuellement un e-mail, le cas échéant.
FRFR
Installation
La sirène peut être placée n’importe où à la portée de la centrale K1.
Activez le mode de test du système K1, puis déclenchez la sirène en appuyant sur le contact anti-sabotage à l’arrière de la sirène.La centrale K1 émettra 3 bips pour confirmer que le détecteur est à sa portée avant son installation.
Installez la sirène à l’aide du ruban double-face ou des vis à expansion fournis dans l’emballage.
Note : Le retrait du capot arrière de la sirène provoquera une alarme. Il est possible de désarmer l’alarme par le biais de votre application K1, puis de continuer l’installation.
Caractéristiques
Modèle : SS-20Alimentation électrique : 4 piles Li-Mn CR123A 3 VNiveau sonore : 90 dBFréquence : EAN 8718868403964 868MHz UPC 859756005223 915MHz Portée sans fil : ≤ 80 m (en zone dégagée)Conditions de fonctionnement : 0 à 50°C, humidité < 90 % HR (sans condensation)Dimensions (L x l x H) : 85 x 85 x 37 mm
NLNL
Introductie
De SS-20 Sirene voor binnen gaat ter plekke af wanneer een sensor van het K1 systeem is geactiveerd met een luide 90dB sirene om eventuele indringers te weren. Het wordt aanbevolen om 2-4 sirenes strategisch rond het huis te plaatsen, aangezien dit indringers weert wanneer die één sirene hebben omzijld maar nog steeds lawaai horen. Indringer houden NIET van aandacht.
Aan de K1 Hub koppelen
De sirene moet voor gebruik eerst aan de K1 Hub worden gekoppeld. Om de sirene te koppelen, raadpleegt u de gebruikershandleiding van de K1 Hub of drukt u op de knop "+" in het K1-gedeelte van de smanos home app en volgt u de instructies op de pagina Accessoires, om uw SS-20 sirene van smanos eenvoudig toe te voegen.
Productoverzicht
Achteraanzicht met montageplaat en waterpas
Sabotage-schakelaar
LED-indicator
LED-indicatorKnippert snel: K1-system slaat alarm.Knippert één keer per 3 seconden: Batterij bijna leeg - vervang de batterijen.
SabotageschakelaarSabotagebeveiliging zorgt ervoor dat pogingen tot het verwijderen van de sirene van de montageplaat leidt tot het afgaan van het alarm en het versturen van een push-bericht en een e-mail, indien geselecteerd.
NLNL
Installatie
De sirene kan op elke locatie worden geplaatst, zolang deze zich binnen het bereik van de K1 Hub bevindt.
Zet het K1-systeem in testmodus en activeer de sirene door op de sabotageschakelaar op de achterkant van de sirene te drukken.De K1 Hub zal voor het installeren 3 keer piepen om te bevestigen dat de sensor binnen het bereik van de hub is geplaatst.
Installeer de sirene met behulp van de dubbelzijdige tape of schroeven met de in de pakketten opgenomen molly's.
Opmerking: Het verwijderen van de achterklep van de sirene zal het alarm doen afgaan. U kunt het alarm uitschakelen via uw K1-app en vervolgens de installatie voortzetten.
Specificaties
Model: SS-20Voeding: 3V CR123A Li-Mn-batterij x 4 stGeluid: 90 decibelFrequentie: EAN 8718868403964 868MHz Draadloos bereik: ≤ 80 m (in open veld)Bedrijfsomstandigheden: 0-50°C, luchtvochtigheid < 90% RH (niet-condenserend)Afmetingen (L x B x H): 85 x 85 x 37 mm
ESES
Introducción
La sirena interior SS-20 sonará en el sitio con un sonido fuerte de 90 dB para persuadir a los posibles intrusos cuando se dispare un sensor del sistema K1. Es inteligente tener 2-4 sirenas colocadas estratégicamente por su hogar, ya que disuaden fácilmente a los intrusos si consiguen burlar una sirena pero aún así oyen RUIDO. A los intrusos NO les gusta la atención.
Vincular el Hub K1
La sirena se debe vincular primero con el Hub K1 antes de usarlo. Para vincular la sirena, consulte el manual del usuario del K1 o la sección K1 de la aplicación smanos home, pulse el botón "+" y siga las instrucciones de la página Accesorios para añadir fácilmente su sirena smanos SS-20.
Descripción general del producto
Vista trasera con la placa de montura y nivel
Interruptor de seguridad
Indicador LED
Indicador LEDParpadea rápidamente: La alarma del sistema K1 está sonando.Parpadea una vez cada 3 segundos: Batería baja, cambie las pilas.
Interruptor de seguridadLa protección antimanipulación garantiza que los intentos de retirar la sirena de la placa de montura resulten en una alarma, una notificación y un correo electrónico, si se selecciona.
ESES
Instalación
Se puede colocar la sirena en cualquier ubicación siempre que esté en el alcance del Hub K1
Establezca el sistema K1 en modo de prueba y, a continuación, dispare la sirena pulsando el interruptor de seguridad de la parte trasera de la sirena.El Hub K1 emitirá 3 pitidos para confirmar que se ha colocado el sensor dentro del alcance del concentrador antes de la instalación.
Instale la sirena usando cinta adhesiva de doble cara o los tornillos de expansión incluidos en el embalaje.
Aviso: Si retira la tapa trasera, la sirena emitirá una alarma. Puede desactivar la alarma a través de la aplicación K1 y continuar con la instalación.
Especificaciones
Modelo: SS-20Alimentación: 4 pila CR123A de 3 V Li-MnSonido: 90 decibeliosFrecuencia: EAN 8718868403964 868MHz UPC 859756005223 915MHz Alcance inalámbrico: ≤ 80 m (en campo abierto)Condiciones de funcionamiento: 0-50 ºC/32-122 ºF, humedad < 90% HR (sin condensación)Medidas (L x A x Al): 85 x 85 x 37mm m/3,35" x 3,35" x 1,46"
PTPT
Introdução
A sirene interior SS-20 dispara no local com um som de sirene forte de 90dB para dissuadir possíveis intrusos quando um sensor do sistema K1 é acionado. É sensato ter 2-4 sirenes colocadas estrategicamente à volta da sua casa, já que isso dissuade facilmente qualquer intruso que silencie uma sirene, mas ainda ouve BARULHO! Os intrusos NÃO gostam de atenção.
Emparelhar com o Hub K1
Esta sirene precisa de ser emparelhada primeiro com o Hub K1 antes de utilizar. Para emparelhar a sirene com o Hub K1, consulte o manual de utilização do Hub K1 ou na secção do K1 da app smanos home, prima o botão "+" e siga as instruções na página Acessórios para adicionar facilmente a sua sirene SS-20 smanos.
Apresentação do Produto
Vista traseira com placa de montagem e nível
Interruptor anti-adulteração
Indicador luminoso
Indicador luminosoPisca rapidamente: O sistema K1 está a disparar um alarme.Pisca uma vez a cada 3 segundos. Bateria fraca, mude as pilhas.
Interruptor anti-adulteraçãoA proteção anti-adulteração garante que qualquer tentativa de remover a sirene da placa de montagem resultará num alarme, notificação automática (push) e possivelmente e-mail, se selecionado.
PTPT
Instalação
A sirene pode ser colocada em qualquer lugar, desde que esteja dentro do alcance do Hub K1.
Coloque o sistema K1 no modo de teste e, em seguida, acione a sirene, premindo o interruptor de anti-adulteração na parte de trás da sirene.O Hub K1 apitará 3 vezes para confirmar que o sensor está colocado dentro do alcance do hub antes da instalação.
Instale a sirene utilizando a fita de dupla-face ou os parafusos incluídos no pacote.
Aviso: Remover a tampa traseira da sirene resultará num alarme. Pode desarmar o alarme através da aplicação do seu K1 e, em seguida, continuar a instalação.
Especificações
Modelo: SS-20Alimentação: 4 x pilhas CR123A Li-Mn de 3 VSom: 90 decibéisFrequência: EAN 8718868403964 868MHz UPC 859756005223 915MHz Alcance sem fios: ≤ 80 m (em áreas abertas)Condições de funcionamento: 0-50 °C/32 °F - 122 °F, humidade< 90% HR (sem condensação)Dimensões (C x L x A): 85 x 85 x 37 mm/3,35" x 3,35" x 1,46"
ITIT
Introduzione
Quando un sensore del sistema K1 viene innescato, la sirena interna SS-20 si attiva sul posto ed emette un potente suono da 90 dB per dissuadere eventuali intrusi. È consigliabile installare 2-4 sirene in posizioni strategiche dell'abitazione come efficace deterrente; se, infatti, l'intruso riesce a disattivare una sirena, le altre unità emetteranno comunque RUMORE! E agli intrusi NON piace attirare l'attenzione.
Abbinamento con l'hub K1
Prima dell'uso, la sirena deve essere abbinata con l'hub K1. A tal scopo, consultare il manuale dell'utente dell'hub K1 o la sezione K1 dell'app smanos home; premere il pulsante "+" e seguire le istruzioni nella schermata Accessori per aggiungere con facilità la sirena smanos SS-20.
Panoramica del prodotto
Lato posteriore con piastra di montaggio e livella a bolla.
Interruttore antimanomissione
Indicatore LED
Indicatore LEDLampeggia rapidamente: il sistema K1 è in allarme.Lampeggia una volta ogni 3 secondi: le batteria sono scarica e devono essere sostituite.
Interruttore antimanomissioneLa protezione antimanomissione fa sì che qualsiasi tentativo di rimuovere la sirena dalla piastra di montaggio causi le seguenti azioni: l'attivazione di un allarme, l'invio di una notifica push e, se selezionato, l'invio di un'e-mail.
ITIT
Installazione
La sirena può essere installata in qualsiasi luogo che si trovi nella portata dell'hub K1.
Impostare il sistema K1 in modalità Test e poi attivare la sirena premendo l'interruttore antimanomissione che si trova sulla parte posteriore.L'hub K1 emetterà 3 bip per confermare che il sensore è stato posizionato nel campo d'azione dell'hub, prima dell'installazione.
Installare la sirena utilizzando il nastro biadesivo o le viti con tasselli inclusi nella confezione.
Nota: la rimozione del coperchio posteriore della sirena farà scattare un allarme. Disattivare l'allarme tramite l'app K1 e poi proseguire con l'installazione.
Specifiche tecniche
Modello: SS-20Alimentazione: 4 batterie Li-Mn CR123A da 3 VSuono: 90 decibelFrequenza: EAN 8718868403964 868MHz Portata wireless: ≤ 80 m (in campo aperto)Condizioni di funzionamento: 0-50 °C/32 - 122 °F, umidità relativa < 90% (senza condensa)Dimensioni (L x P x A): 85 x 85 x 37 mm
PLPL
Wstęp
Wewnętrzna Syrena Alarmowa SS-20 uruchomi się głośnym 90 dB alarmem jak tylko któryś z czujników systemu K1 zostanie wzbudzony przez intruza. Rozsądnym jest posiadać 2-4 syren rozstawionych w Twoim domu tak aby donośny dźwięki syreny odstraszał intruza lub utrudniał mu nieuprawnione działania w Twoim domu. Pamiętaj! Złodzieje nie lubią zwracać na siebie uwagi.
Parowanie z Centralą K1
Syrena alarmowa musi być sparowana z Centralą K1 przed pierwszym użyciem. Żeby połączyć urządzenia proszę sprawdzić instrukcję centrali K1 lub w aplikacji "smanos home" nacisnąć + i podążać za instrukcjami.
Wygląd urządzenia
Wygląd z tyłu wraz obudową montażową
Wyłącznik antysabotażowy
Dioda LED
Dioda LEDMruga szybko: System K1 uruchomił alarmMruga raz na 3 sekundy: Słaba bateria, proszę zmienić je niezwłocznie.
Wyłącznik antysabotażowyZabezpieczenie antysabotażowe zabezpiecza przed niepowołanym usunięciem pokrywy obudowy. Działanie takie wzbudza natychmiastowy alarm, wysyła powiadomienie lub emaila ( jeśli wybrano tę opcję).
PLPL
Montaż
Syrena alarmowa może być umieszczona w dowolnym miejscu byle tylko była w zasięgu połączenia z centralą.
Ustaw system K1 w Tryb Test ( w aplikacji "smanos home") narusz stan syreny poprzez naciśniecie wyłącznika antysabotażowego na tylnej obudowie , Centrala K1 wyda potrójny dźwięk potwierdzający połączenie i odpowiedni zasięg miedzy urządzeniami.
Zamontuj syrenę w przy pomocy podwójnej taśmy klejącej lub zestawu wkrętów dostarczonych w zestawie.
Uwaga: Zdejmowanie tylnej obudowy czujnika będzie skutkowało alarmem. Rozbrój system poprzez aplikację i dopiero kontynuuj montaż.
Specyfikacja
Model: SS-20Zasilanie: 3V CR123A Li-Mn baterie 4 szt.Głośność: 90 DecybeliCzęstotliwość: 868MHz /EU lub 915MHzZasięg: ≤ 80 m (otwarta przestrzeń)Warunki użytkowania:0-50°C / 32° - 122°F, wilgotności< 90% RH (bez kondensacji)Wymiary (L x W x H): 85 x 85 x 37mm