spb2015 program - unibo.itdiqumaspab.dicam.unibo.it/programspb_final.pdf · spb2015 program ....
TRANSCRIPT
1
SPB2015 Program International Conference on Shells, Plates and Beams
9-11 September 2015 - University of Bologna, Italy Conference Chairs: Antonio J.M. Ferreira, University of Porto, Portugal Erasmo Viola, University of Bologna, Italy Francesco Tornabene, University of Bologna, Italy Local Organizing Committee: Nicholas Fantuzzi, University of Bologna, Italy Michele Bacciocchi, University of Bologna, Italy
General Information
Venue: School of Engineering and Architecture, University of Bologna Viale del Risorgimento 2, 40136, Bologna, Italy http://www.spb2015.dicam.unibo.it/
Registration opens from 08h00 to 18h00, 9-11 September Pre-Registration on Tuesday 8 September from 15h00 to 18h00 Coffee breaks from 10h30 to 11h00, 9-11 September and from 16h00 to 16h30, 9-10 September Lunch-break from 13h00 to 14h00, 9-11 September Banquet Thursday 10 September @ 20h00 @ Trattoria “Della Santa”, location details at the registration desk (ticket required)
2
Conference Location The Conference Venue will be the School of Engineering and Architecture, University of Bologna, Viale del Risorgimento 2, 40136 Bologna, Italy
The conference will take place in the "Aule Nuove" area of the School behind the main entrance, directions will be given.
In order to reach the conference site, it is possible to go through the main entrance (Viale del Risorgimento 2) across the main corridor and follow directions, or using the second entrance (Via Vallescura) and at the first T-section go on the left.
3
Travel and Accommodation How to get to Bologna Bologna is located in the northern part of Italy. You can reach Bologna by airplane, by train and by car. Bologna has an International Airport with good connections to most of the European airports. Bologna has very good train connections with most of the European cities. Bologna is reachable by car by the well-organized Italian motorway system.
Bologna Outskirts
Bologna City Center
4
By Airplane Bologna's closest airport is Guglielmo Marconi (Bologna) International Airport (IATA: BLQ), just a few minutes from the city center, served by taxi and a special bus line called the Aerobus. A taxi from the airport to the center costs about €15. An Aerobus Ticket costs €6, and it stops outside the main terminus building. The ticket is also valid during 1 hour on the other busses in Bologna. Bus 54 goes towards the west suburbs of Bologna, and will get you on to the 'main' routes. Another bus stop is about 10 minutes walk from the airport (bus stop name: Birra - other side of the elevated motorway, follow the road out of the airport, turn right at the first roundabout and straight through the second roundabout) and you can board bus 81 and 91 which have an end stop at Bologna Central Train Station. Bus tickets are valid for 60 minutes travel and cost €1,5. Go to the website of the local bus company, TPER, and you will find maps that show all routes including the airport. Ryanair flies to Bologna Gugliemo Marconi. British Airways and Turkish Airlines have 2 or 3 flights per day (depending on season) from/to London Heathrow and from/to Istanbul Ataturk respectively. Marconi Airport also has numerous international connections available, including nonstop flights to Amsterdam, Brussels (National), Charleroi (Brussels South), Copenhagen, Dublin, Edinburgh, Istanbul, Lisbon, London, Madrid, Moscow, Paris, Prague, Vienna, Warsaw (Modlin), Wroclaw and Zagreb. By Train Due to its central location and geography, Bologna has emerged as the main rail transport hub of northern Italy, making it very well-connected with other major Italian centers. From the 14th of December 2008 the new high speed railway line is available from/to Milan, shortening the journey to 65 minutes. Bologna is also 37 minutes from Florence, 2 hours 20 from Rome, 2 hours from Venice, 1 hour from Ferrara, etc. The new high speed train line between Rome and Bologna is now fully available and can make trips much faster. There is also an overnight sleeper service from Paris Bercy to Bologna. Departs Paris 6:52PM in the evening, and arrives Bologna at 6AM. Return departs Bologna 10:30PM arrives Paris 9:06AM. By Car The city is at the junction of the A1, A14 and A13 highways, and so is easily accessible from anywhere in Italy. Most traffic from Milan would exit the A1 and take the Tangenziale, but beware this road at rush hour because it is horrendously packed. Expect to use 2 hours from the A1 exit to the Tangenziale to the center at certain peak times over summer busy weekends, especially at the beginning and end of August.
Get around Layout of the city Looking at the map of the city (it is possible to get a free one at the Tourist Information Center in Piazza Maggiore), the first thing to do to orient yourself is to find the Due Torri landmark in the center of the free map. The center of the city is surrounded by the Viali, a circular road easily recognizable. The northeast quadrant of the map is the university district (which unlike US campus is an integral part of the city and not a separate compound). The two southern quadrants of your city map are residential sections of the city, and not common tourist areas. However, walking outside the city center, further to the south, you will come upon hills and the Giardini Margherita, the largest park of the city.
5
Plan your travel A great place to start planning how to get around Emilia-Romagna region and Bologna city using buses and trains is on: By bus The TPER company is in charge of the buses in Bologna. Useful information can be found on their website: www.tper.it. Tickets may be purchased prior to boarding the bus, or on the bus where there are ticket machines. If you see 2 machines on a bus (usually Red and Yellow) the Red one will sell you a ticket (1,5 EUR, valid for 1 hour) and the Yellow one will validate a 'season' or multi trip ticket. Information and ticket centers are available in central locations (railway station, coach station, city center). Useful bus maps are available there. These main ticket centres often sell multi trip tickets at a discount (eg €10 worth of travel for €8.50). You can also purchase tickets in many shops (newspaper sellers, tobacconists, cafes). On bike Bikes are most popular amongst the people of Bologna. They are available for hire on various location around the city (one near the train station). You can ride on the many bike trails and on the side of the road. Be sure to lock them safely with a good lock, as they get stolen all around town, especially around the University. On foot Bologna is a great place around which to travel on foot, as getting around the city is very simple with clear street signs. It is also a great way to find hidden gems such as Pizzerias packed with Italians (so you KNOW you reached the right place). Be a bit careful when crossing roads, the city centre swarms with scooters and small motorcycles (cars banned during the day) and they ride them everywhere.
How to get to the Conference The Conference Venue stands in the Saragozza district at N° 2, Viale del Risorgimento. On foot If you have a hotel in the city center you can come on foot in around 15 minutes walk. By Bus The School of Engineering and Architecture is well-connected by several buses. If you hotel is near the ring-road (so-called Viali) catch the 32 or 33 bus and get off at “Liceo Righi”. From the centre the bus is the number 20 (Porta Saragozza stop). In either case, allow about 15 minutes. By Train If you arrive at the train station, catch the 33 bus and get off at “Liceo Righi”. By Car If arriving by car from outside Bologna, leave the motorway ring-road at Exit 5 and follow directions to the center. On reaching the avenues forming the inner ring-road, make your way to Porta Saragozza.
6
Room 6.1 Opening Ceremony @ Wednesday September 9 @ 09h00
(Conference Chair)
Plenary Lectures (Room 6.1)
WEDNESDAY 9 September 2015 Chair: Carrera, Erasmo (Polytechnic of Turin, Italy) 09h30 Static-kinematic duality in beams, plates, shells and its central role in the Finite Element Method Carpinteri, Alberto (Polytechnic of Turin, Italy) 10h00 Third-order thermomechanically coupled laminated plates: modeling and analysis in a unified reduced framework Rega, Giuseppe (Sapienza University Rome, Italy)
THURSDAY 10 September 2015 Chair: Ascione, Luigi (University of Salerno, Italy) 09h00 Virtual element methods for plates and shells. Chinosi, Claudia (University of Piemonte Orientale, Italy) 09h30 Theories and Computational Models for Beams, Plates and Shells in Unified Form. Carrera, Erasmo (Polytechnic of Turin, Italy) 10h00 Smart Shells: Sensing, Actuation and Control. Tzou, Horn-Sen (University of ZheJiang, China)
FRIDAY 11 September 2015 Chair: Rega, Giuseppe (Sapienza University Rome, Italy) 09h00 Precasting of large span shells and plates. Giuliani, Gian Carlo (Redesco Research-Design-Consulting, Italy) 09h30 Whole composite structures: between research and normative. Ascione, Luigi (University of Salerno, Italy) 10h00 On non linear analysis of masonry shells. Tralli, Antonio (University of Ferrara, Italy)
7
Parallel Sessions (every paper 20 minutes, including 5
minutes discussion)
8
WEDNESDAY 9 September Room 6.1
Session on Beams
Chairs: Wahrhaftig, Alexandre (Federal University of Bahia, Brazil)
Capdevielle, Sophie (Université Grenoble Alpes, France) 11h00 15 | Challengers for designing a wooden beam of composed section Wahrhaftig, Alexandre (Federal University of Bahia, Brazil) [email protected] Carvalho, Ricardo (Federal University of Bahia, Brazil) [email protected] 11h20 161 | Development of modeling techniques for unidirectional composite ribs for static and impact strength analysis of airframes Chernov, Andrey (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Shanygin, Alexander (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Kondakov, Ivan (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] 11h40 71 | Investigation of fracture toughness of cracked concrete beam repaired by epoxy Kan, Yu-Cheng (Chaoyang University of Technology, Taiwan) [email protected] Taiwan Lee, Hung-Wei (Chaoyang University of Technology, Taiwan) [email protected] 12h00 62 | A multifiber beam model coupling damage and warping for reinforced concrete structures under multiaxial loads Capdevielle, Sophie (Université Grenoble Alpes, France) [email protected] Grange, Stéphane (Université Grenoble Alpes, France) Dufour, Frédéric (Université Grenoble Alpes, France) Desprez, Cédric (Université de Paris - Est, France) 12h20 75 | FE Analysis of Mode II Delamination in Laminated Composite Structures with General Fiber Orientation Samborski, Sylwester (Lublin University of Technology, Poland) [email protected] Debski, Hubert (Lublin University of Technology, Poland) [email protected] Teter, Andrzej (Lublin University of Technology, Poland) [email protected] 12h40 138 | Numerical and experimental determination of natural frequencies and critical loads for compressed open thin-walled beams Piana, Gianfranco (Sapienza Università di Roma, Italy) [email protected] Carpinteri, Alberto (Politecnico di Torino, Italy) [email protected] Lofrano, Egidio (Sapienza Università di Roma, Italy) [email protected] Malvano, Riccardo Manuello, Amedeo (Politecnico di Torino, Italy) [email protected] Ruta, Giuseppe (Sapienza Università di Roma, Italy) [email protected] 13h00 Lunch Break
9
WEDNESDAY 9 September Room 6.2
Session on Shells
Chairs: Kulikov, Gennady M. (Tambov State Technical University, Russia)
Burzynski, Stanislaw (Gdansk University of Technology, Poland) 11h00 12 | A New Concept of Sampling Surfaces and its Implementation for Layered and Functionally Graded Doubly-Curved Shells Kulikov, Gennady M. (Tambov State Technical University, Russia) [email protected] Plotnikova, Svetlana V. (Tambov State Technical University, Russia) 11h40 27 | Global Geometric Aspects of Shell Deformation Sun, Bohua (Cape Peninsula University of Technology, South Africa) [email protected] 12h00 52 | Analytical and numerical analysis of composite impact attenuators Boria, Simonetta (University of Camerino, Italy) [email protected] Pettinari, Silvia (University of Camerino, Italy) [email protected] Giannoni, Fabio (University of Camerino, Italy) [email protected] Cosimi, Giancarlo (University of Camerino, Italy) [email protected] 12h20 50 | Comparison of Two Shell Theories of Composite Materials Chung, Samuel W. (University of Utah, USA) [email protected] Ju, Gisu (Young Nam University, USA) [email protected] 12h40 146 | On elasto-plastic deformations in 6 parameter nonlinear shell theory with FGM Burzynski, Stanislaw (Gdansk University of Technology, Poland) [email protected] Chroscielewski, Jacek (Gdansk University of Technology, Poland) [email protected] Daszkiewicz, Karol (Gdansk University of Technology, Poland) [email protected] Witkowski, Wojciech (Gdansk University of Technology, Poland) [email protected] 13h00 Lunch Break
10
WEDNESDAY 9 September Room 6.1
General Session
Chairs: Rizzoni, Raffaella (University of Ferrara, Italy)
Meola, Carosena (University of Naples Federico II, Italy) 14h00 123 | Asymptotic analysis of nonlinear elastic adhesives Rizzoni, Raffaella (University of Ferrara, Italy) [email protected] Dumont, Serge (Laboratoire Amiénois de Mathématique Fondamentale et Appliquée, France) [email protected] Lebon, Fréderic (Laboratoire de Mécanique et d’Acoustique, France) [email protected] 14h20 162 | On dynamic problems of anisotropic strip-beam and plates Aghalovyan, Mher L. (The Institute of Mechanics of National Academy of Sciences, Armenia) [email protected] 14h40 155 | Infrared thermography to evaluate impact damaging of thermoset- and thermoplastic-matrix composites Meola, Carosena (University of Naples Federico II, Italy) [email protected] Boccardi, Simone (University of Naples Federico II, Italy) Carlomagno, Giovanni M. (University of Naples Federico II, Italy) Boffa, Natalino D. (University of Naples Federico II, Italy) Ricci, Fabrizio (University of Naples Federico II, Italy) Simeoli, Giorgio (University of Naples Federico II, Italy) Russo, Pietro (National Council of Research, Italy) 15h00 78 | Simulating the Warping of Thin Coated Si Wafers Using Ansys Layered Shell Elements Schicker, Johannes (CTR Carinthian Tech Research AG, Austria) [email protected] Arnold, Thomas Debasio, Martin Hirschl, Christina Kraft, Martin Vollert, Natalie 15h20 141 | Evolutionary Analysis of Masonry Arches: Effects of Aspect Ratio and Size Scale Carpinteri, Alberto (Politecnico di Torino, Italy) [email protected] Lacidogna, Giuseppe (Politecnico di Torino, Italy) [email protected] Accornero, Federico (Politecnico di Torino, Italy) [email protected] Testone, Luca (Politecnico di Torino, Italy) [email protected] 15h40 139 | Snap-Through vs. Eulerian Instability in Arch Structures Affected by Geometrical Imperfections Carpinteri, Alberto (Politecnico di Torino, Italy) [email protected] Bazzucchi, Fabio (Politecnico di Torino, Italy) [email protected] Manuello, Amedeo (Politecnico di Torino, Italy) [email protected] 16h00 Coffee-Break
11
WEDNESDAY 9 September Room 6.2
Session on Plates
Chairs: Sawarkar Sameer (Indian Institute of Technology, India) Landi, Luca (DICAM University of Bologna, Italy) 14h00 28 | Semi-analytical Solutions for Electro-mechanical Loading of an All-round Simply Supported Smart Plate Sawarkar Sameer (Indian Institute of Technology, India) [email protected] Pendhari Sandeep (Veermata Jeejabai Technological Institute, India) [email protected] Desai Yogesh (Indian Institute of Technology, India) [email protected] 14h20 99 | The influence of patch load length on the ultimate strength of longitudinally stiffened plate girder Kovacevic, Sasa (University of Belgrade, Serbia) [email protected] Markovic, Nenad (University of Belgrade, Serbia) [email protected] 14h40 97 | Aspects of error estimates in quantity of interest for the FSDT laminated plate model and GFEM Mendonça (Federal University of Santa Catarina, Brazil) [email protected] Chamoin (LMT-Cachan, secteur Structures & Systèmes, France) [email protected] de Barcellos (Federal University of Santa Catarina, Brazil) [email protected] 15h00 51 | The effect of current types on the microstructure and tribological properties of Ni/nanoAl2O3 composite coatings Kucharska, Beata (Warsaw University of Technology, Poland) [email protected] Krawczynska, Agnieszka (Warsaw University of Technology, Poland) [email protected] Poplawski, Karol (Warsaw University of Technology, Poland) Sobiecki, Jerzy R. (Warsaw University of Technology, Poland) [email protected] 15h20 67 | Usage of IPN water-based resins in the execution of reinforcements of RC beams with composite materials Diotallevi, Pier Paolo (DICAM University of Bologna, Italy) [email protected] Landi, Luca (DICAM University of Bologna, Italy) [email protected] Guiduzzi, Marco (DICAM University of Bologna, Italy) [email protected] Credali, Lino (Ardea Progetti e Sistemi, Italy) [email protected] Ussia, Gianluca (Ardea Progetti e Sistemi, Italy) [email protected] 15h40 61 | Generalized plate model-application to laminated glass Viverge, Kevin (Université de Lyon, France) [email protected] Boutin, Claude (Université de Lyon, France) [email protected] 16h00 Coffee Break
12
WEDNESDAY 9 September Room 6.1
General Session
Chairs: Abouhamzeh, Morteza (Delft University of Technology, Netherlands)
Masae Kanda (Tokai University, Japan) 16h30 43 | Distortion of GLARE Panels Due to Cut-outs Abouhamzeh, Morteza (Delft University of Technology, Netherlands) [email protected] Sinke, Jos (Delft University of Technology, Netherlands) Benedictus, Rinze (Delft University of Technology, Netherlands) 16h50 55 | Development of in-plane faiure criteria for fiber-reinforced composite materials Zhang, Xiaobo (Delft University of Technology, Netherlands) [email protected] Jiang, Xiaoli (Delft University of Technology, Netherlands) [email protected] Lodewijks, Gabriel (Delft University of Technology, Netherlands) [email protected] 17h10 109 | Safety Electron Beam Irradiated Adhesion between Polyurethane and Metal Sheets Masae Kanda (Tokai University, Japan) [email protected] Masato Uyama (Tokai University, Japan) Yoshitake Nishi (Tokai University,Japan) [email protected] 17h30 44 | Coupling effects of pressure and plastic folding on the buckling morphologies of thin films on substrate Colin, Jerome (Université de Poitiers, France) [email protected] Hamade, Sami (Université de Poitiers, France) [email protected] Coupeau, Chrstophe (Université de Poitiers, France) [email protected] Parry, Guillaume (Universite de Grenoble, France) [email protected] Durinck, Julien (Université de Poitiers, France) [email protected] Grilhé, Jean (Université de Poitiers, France) [email protected] Cimetière, Alain (Université de Poitiers, France) [email protected]
13
WEDNESDAY 9 September Room 6.2
Session on Shells
Chairs: Araujo, Aurelio (Universidade de Lisboa, Portugal) Fomin, Victor (Central Aerohydrodynamic Institute (TsAGI), Russia) 16h30 148 | Buckling and geometrically nonlinear analysis of soft core sandwich plates and shells Moita, Jose (Universidade de Lisboa, Portugal) [email protected] Araujo, Aurelio (Universidade de Lisboa, Portugal) [email protected] Mota Soares, Cristovao (Universidade de Lisboa, Portugal) [email protected] Mota Soares, Carlos (Universidade de Lisboa, Portugal) [email protected] 16h50 147 | Middle Byzantine masonry domes: an investigation on the structural problems Manzo, Antonella (Politecnico di Milano, Italy) [email protected] Chesi, Claudio (Politecnico di Milano, Italy) [email protected] Sumini, Valentina (Politecnico di Milano, Italy) 17h10 96 | Load-bearing capability of composite cylindrical stiffened panels with account of post-buckling failure of skin Fomin, Victor (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Dubovikov, Evgeny (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Mareskin, Ivan (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] 17h30 107 | Analysis in theory and experiment on waves propagating in a vibrating cylindrical shell Hyun Gwon Kil (University of Suwon, South Korea) [email protected] Chan Lee (University of Suwon, South Korea) [email protected] Sang Moon Hwang (R&D center of Pro-power communication Co., Ltd, South Korea) [email protected]
14
THURSDAY 10 September Room 6.1
Session on Beams
Chairs: Skrinar, Matjaž (University of Maribor, Slovenia) Pagani, Alfonso (Politecnico di Torino, Italy) 11h00 128 | Effect of localized inertia on the vibrations of civil engineering structures by 1D component-wise models Pagani, Alfonso (Politecnico di Torino, Italy) [email protected] Carrera, Erasmo (Politecnico di Torino, Italy) [email protected] Colonna, Giovanni (Politecnico di Torino, Italy) [email protected] 11h20 150 | Lateral-torsional buckling of compressed and highly variable cross section beams Mascolo Ida (University of Naples Federico II, Italy) [email protected] Mario Pasquino (University of Naples Federico II, Italy) [email protected] 11h40 66 | Detection of damage in RC beams with NSM CFRP by frequency measures Capozucca, Roberto (Università Politecnica Marche, Italy) [email protected] Bossoletti, Sonia (Università Politecnica Marche, Italy) [email protected] Corina, Valeria (Università Politecnica Marche, Italy) 12h00 149 | On some recent developments of GBT for composite beams de Miranda, Stefano (University of Bologna, Italy) [email protected] Melchionda, Domenico (University of Bologna, Italy) [email protected] Patruno, Luca (University of Bologna, Italy) [email protected] Ubertini, Francesco (University of Bologna, Italy) [email protected] 12h20 68 | Finite Element for Hinged Multi-Stepped Beams and Beams with linearly-varying heights having an arbitrary number of Cracks Skrinar, Matjaž (University of Maribor, Slovenia) [email protected] 12h40 33 | Parameters affecting the reduction factor in pedestrian load models based on pulsating stationary force Štimac Grandić, Ivana (Univeristy of Rijeka, Croatia) [email protected] Grandić, Davor (Univeristy of Rijeka, Croatia) [email protected] Berić, Nikola (Univeristy of Rijeka, Croatia) [email protected] 13h00 Lunch Break
15
THURSDAY 10 September Room 6.2
Session on Plates
Chairs: Atashipour, Seyed Rahim (University of Genoa, Italy) Zaccariotto, Mirco (University of Padova, Italy) 11h00 120 | Elastic analysis of a double side-coated circular plate with functionally graded interlayers Sburlati, Roberta (University of Genoa, Italy) [email protected] Atashipour, Seyed Rasoul (University of Technology, Luleå, Sweden) [email protected] Atashipour, Seyed Rahim (University of Genoa, Italy) [email protected] 11h20 133 | Alternative thin plate formulation using a peridynamic approach Zaccariotto, Mirco (University of Padova, Italy) [email protected] Sarego, Giulia (University of Padova, Italy) [email protected] Dipasquale, Daniele (University of Padova, Italy) [email protected] Galvanetto, Ugo (University of Padova, Italy) [email protected] 11h40 58 | Buckling analysis of a simply supported rectangular orthotropic composite plate with delamination Juhász, Zoltán (Budapest University of Technology and Economics, Hungary) [email protected] Szekrényes, András (Budapest University of Technology and Economics, Hungary) [email protected] 12h00 86 | A Solution for the Superabundant Unknown Problem in the Boundary Element Analysis of Plates Hiroyuki Kisu (Nagasaki University, Japan) [email protected] Guiming Rong (Nagasaki University, Japan) [email protected] Takanori Yazawa (Nagasaki University, Japan) [email protected] Toru Takase (Nagasaki University, Japan) [email protected] 12h20 158 | Verification of engineering methods of accounting postbuckling deforming by the means of non-linear FE methods Limonin, Mikhail (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Dudarkov, Yury (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] Levchenko Evgeny (Central Aerohydrodynamic Institute (TsAGI), Russia) [email protected] 12h40 114| Effective and Efficient Hybrid Model for Buckling Analysis of Hierarchical Composite Stiffened Plates Tian, Kuo (Dalian University of Technology, China) [email protected] Wang, Bo (Dalian University of Technology, China) [email protected] Hao, Peng (Dalian University of Technology, China) [email protected] Zheng, Yanbing (Dalian University of Technology, China) [email protected] Cai, Yuanwu (China Academy of Railway Sciences, China) [email protected] 13h00 Lunch Break
16
THURSDAY 10 September Room 6.1
Session on Beams
Chairs: Samborski, Sylwester (Lublin University of Technology, Poland) Zulli, Daniele (University of L'Aquila, Italy) 14h00 70 | Mode I Energy Release Rate Variability along Delamination Front in Laminated Composite Structures with General Fiber Orientation Samborski, Sylwester (Lublin University of Technology, Poland) [email protected] 14h20 76 | Dynamic equations for a micropolar cylinder Abadikhah, Hossein (Chalmers University of Technology, Sweden) [email protected] Folkow, Peter D. (Chalmers University of Technology, Sweden) [email protected] 14h40 36 | Semi-analytic analysis of composite beams using the scaled boundary finite element method Jung, Jonathan Daniel (Technische Universität Darmstadt, Germany) [email protected] Becker, Wilfried (Technische Universität Darmstadt, Germany) [email protected] 15h00 72 | Interlaminar stresses in curved sections of composite box beams Unsinn, Michael (Technische Universität Darmstadt, Germany) [email protected] Becker, Wilfried (Technische Universität Darmstadt, Germany) [email protected] 15h20 157 | A one dimensional beam-like model for composite tubes with foam core Luongo, Angelo (University of L'Aquila, Italy) [email protected] Scognamiglio, Ilaria (University of L'Aquila, Italy) [email protected] Zulli, Daniele (University of L'Aquila, Italy) [email protected] 15h40 73 | Post-buckling behavior of thin-walled columns made of in-plane coupled composite laminates Teter, Andrzej (Lublin University of Technology, Poland) [email protected] Pasierbiewicz, Damian (Lublin University of Technology, Poland) Kolakowski, Zbigniew (Lodz University of Technology, Poland) [email protected] 16h00 Coffee Break
17
THURSDAY 10 September Room 6.2
Session on Plates
Chairs: Dozio, Lorenzo (Politecnico di Milano, Italy)
Fantuzzi, Nicholas (University of Bologna, Italy) 14h00 164 | Thermo-mechanical modeling of photovoltaic laminates by means of unified formulation Carrera, E. (Politecnico di Torino, Italy) [email protected] Cinefra, M. (Politecnico di Torino, Italy) [email protected] Rambaldi, F. (Politecnico di Torino, Italy) 14h20 151 | Modal characteristics of rotating moderately thick composite plates Invernizzi, Davide (Politecnico di Milano, Italy) [email protected] Dozio, Lorenzo (Politecnico di Milano, Italy) [email protected] 14h40 152 | The vk-Ritz method for bending, vibration and buckling analysis of heterogeneous multilayered plates Dozio, Lorenzo (Politecnico di Milano, Italy) [email protected] Vescovini, Riccardo (Politecnico di Milano, Italy) [email protected] Spalluto, Alberto (Politecnico di Milano, Italy) Spinelli, Matteo 15h00 53 | Elastodynamics of FGM plates by a mesh-free method Sladek V. (Institute of Construction and Architecture, Slovak Academy of Sciences, Slovakia) [email protected] Sator L. (Institute of Construction and Architecture, Slovak Academy of Sciences, Slovakia) [email protected] Sladek J. (Institute of Construction and Architecture, Slovak Academy of Sciences, Slovakia) [email protected] 15h20 168 | Static and dynamic analyses of arbitrarily shaped laminated composite structures Fantuzzi, Nicholas (University of Bologna, Italy) [email protected] Bacciocchi, Michele (University of Bologna, Italy) [email protected] Tornabene, Francesco (University of Bologna, Italy) [email protected] Viola, Erasmo (University of Bologna, Italy) [email protected] 15h40 170 | Vibration of a Functionally Graded (FG) Microplate under a Moving Load Using Neutral Surface Based on the Modified Couple Stress Theory S ̧ims ̧ek, Mesut (Yildiz Technical University, Turkey) [email protected] Aydin, Mustafa (Yildiz Technical University, Turkey) 16h00 Coffee Break
18
THURSDAY 10 September Room 6.1
General Session
Chairs: Aghalovyan, Lenser A. (Institute of Mechanics of National Academy of Sciences of
Armenia, Armenia) Babilio, Enrico (University of Naples “Federico II”, Italy) 16h30 101 | Simulation of optimal polarization for three-layered piezoelectric transducer using ACELAN package Oganesyan, Pavel A. (Southern Scientific Center of Russian Academy of Sciences, Rostov-on-Don, Russia) [email protected] Soloviev, Arcady N (Don State Technical University, Rostov-on-Don, Russia) [email protected] Skaliukh, Alexander S (Sothern Federal University, Rostov-on-Don, Russia) [email protected] Shevtsova, Maria S (Southern Scientific Center of Russian Academy of Sciences, Rostov-on-Don, Russia) [email protected] Shevtsov, Sergey N (Southern Scientific Center of Russian Academy of Sciences, Rostov-on-Don, Russia) [email protected] 16h50 135 | The dynamics of frames braced with functionally graded members Babilio, Enrico (University of Naples “Federico II”, Italy) [email protected] 17h10 60 | On asymptotic theory of beams, plates and shells Aghalovyan, Lenser A. (Institute of Mechanics of National Academy of Sciences of Armenia, Armenia) [email protected] Aghalovyan, Mher A. (Institute of Mechanics of National Academy of Sciences of Armenia, Armenia) [email protected] 17h30 54 | An equilibrium approach to finite element modelling of plates and shells Maunder, Edward A. W. (University of Exeter, United Kingdom) [email protected] Izzuddin, Bassam, A. (Imperial College, United Kingdom) [email protected]
19
THURSDAY 10 September Room 6.2
Session on Shells
Chairs: Altekin, Murat (Yildiz Technical University, Turkey) Bacciocchi, Michele (University of Bologna, Italy) 16h30 108 | Large deflection analysis of shallow conical shells Altekin, Murat (Yildiz Technical University, Turkey) [email protected] Yukseler, R. Faruk (Yildiz Technical University, Turkey) [email protected] 16h50 136 | Analysis of Laminated Structures with Variable Number of Layers by CUF Shell Elements Cinefra, Maria (Politecnico di Torino, Italy) [email protected] Valvano, Stefano (Politecnico di Torino, Italy) [email protected] Carrera, Erasmo (Politecnico di Torino, Italy) [email protected] 17h10 167 | Higher-order theories for the structural analysis of doubly-curved shells and panels made of innovative materials Tornabene, Francesco (University of Bologna, Italy) [email protected] Fantuzzi, Nicholas (University of Bologna, Italy) [email protected] Bacciocchi, Michele (University of Bologna, Italy) [email protected] Viola, Erasmo (University of Bologna, Italy) [email protected] 17h30 40 | Theories and Analyses Thick Hyperbolic paraboloidal Composite Shells Mohammad Zannon (Tafila Technical University, Jordan) [email protected] Mohamad Qatu (Central Michigan University, USA) [email protected]
20
FRIDAY 11 September Room 6.1
Session on Shells
Chairs: Della Puppa, Giovanni (RWTH Aachen University, Germany)
Kobayashi, Takaya (Mechanical Design & Analysis Corporation, Japan) 11h00 29 | Thin-Walled Tubes with a Local Sharp Cut under Cyclic Bending Kuo-Long Lee (Far East University, Taiwan) [email protected] Yung-Ju Tseng (National Cheng Kung University, Taiwan) [email protected] Wen-Fung Pan (National Cheng Kung University, Taiwan) [email protected] 11h20 30 | Analysis of Material-Related Instability Problems for Cylindrical Shells Kobayashi, Takaya (Mechanical Design & Analysis Corporation, Japan) [email protected] Mihara, Yasuko (Mechanical Design & Analysis Corporation, Japan) [email protected] Fujii, Fumio (Gifu University, Japan) [email protected] 11h40 63 | Model development and comparisons for light shell structures in textile reinforced concrete Senckpiel, Tilo (TU Dresden, Department of Civil Engineering, Germany) [email protected] Häußler-Combe, Ulrich (TU Dresden, Department of Civil Engineering, Germany) [email protected] 12h00 153 | Multilayered metal panels for doubly curved freeform shell structures Della Puppa, Giovanni (RWTH Aachen University, Germany) [email protected] Pofahl, Thorsten (RWTH Aachen University, Germany) [email protected] Trautz, Martin (RWTH Aachen University, Germany) [email protected] Bailly, David (RWTH Aachen University, Germany) [email protected] Hirt, Gerhard (RWTH Aachen University, Germany) [email protected] 12h20 110 | Surrogate-based optimum design of curvilinearly stiffened panels for cutout reinforcement Hao, Peng (Dalian University of Technology, China) [email protected] Wang, Bo (Dalian University of Technology, China) [email protected] Tian, Kuo (Dalian University of Technology, China) [email protected] 12h40 77 | Effect of welding induced imperfections on the buckling load capacity of shells Schaumann, Peter (Institute for Steel Construction, Germany) [email protected] Colmann, Mareike (Institute for Steel Construction, Germany) [email protected] Gottschalk, Malte (Institute for Steel Construction, Germany) [email protected] 13h00 Lunch Break
21
FRIDAY 11 September Room 6.2
Session on Beams
Chairs: Ascione, Luigi (University of Salerno, Italy) Kubiak, Tomasz (Lodz University of Technology, Poland) 11h00 57 | Effect of geometric imperfection on the mechanical behavior of PFRP profiles Ascione L. (University of Salerno, Italy) [email protected] Berardi V.P. (University of Salerno, Italy) [email protected] Spadea S. (University of Salerno, Italy) [email protected] 11h20 45 | Experimental investigations of thin-walled GFRP beams subjected to pure bending Kubiak, Tomasz (Lodz University of Technology, Poland) [email protected] Czapski, Pawel (Lodz University of Technology, Poland) [email protected] Swiniarski Jacek (Lodz University of Technology, Poland) [email protected] Urbaniam, Mariusz (Lodz University of Technology, Poland) [email protected] 11h40 169 | Bifurcational Buckling of Two-Dimensional Functionally Graded (2D-FG) Beams Resting on the Winkler Elastic Foundation S ̧ims ̧ek, Mesut (Yildiz Technical University, Turkey) [email protected] 12h00 137 | Nondestructive Testing Method for Curved Composite Surface Based on Twin-robot Technology Zongxing Lu (Beijing Institute of Technology, China) [email protected] Chunguang Xu (Beijing Institute of Technology, China) [email protected] 12h20 92 | Crack propagation effect at the interface of a composite beam Hamli Benzahar, Hamid (University of Djilali Bounaama, Khemis Miliana, Algeria) [email protected] Hammoudi, Imène (University of Sciences and Technology Houari Boumediene, Algeria) [email protected] Chabaat, Mohamed (University of Sciences and Technology Houari Boumediene, Algeria) [email protected] 12h40 165 | Bending Capacity of the Post-tensioned Steel Beam with the Sandwich Plate System Ryu, Jaeho (Korea University, South Korea) [email protected] Lho, Seung-Hee (Korea University, South Korea) [email protected] Ju, Young K. (Korea University, South Korea) [email protected] Yoon, Sung-Won (Seoul National University of Science & Technology, South Korea) [email protected] Park, Man Woo (Dongbu Steel Co., Ltd., South Korea) [email protected] 13h00 Lunch Break
22
FRIDAY 11 September Room 6.1
Session on Plates and Shells
Chairs: Marzani, Alessandro (University of Bologna, Italy) Mergny, Elke (Université Catholique de Louvain, Belgium) 14h00 23 | Description of a design method for cryogenic concrete tanks based on a comparison between 2D and 3D numerical models Mergny, Elke (Université Catholique de Louvain, Belgium) [email protected] Poncin, Pierre (Université Catholique de Louvain, Belgium) [email protected] Latteur, Pierre (Université Catholique de Louvain, Belgium) [email protected] 14h20 171 | Revisiting the Problem of Vibration Analysis of Clamped Plates Eisenberger, Moshe (Technion – Israel Institute of Technology, Israel) [email protected] Deutsch, Aharon (Technion – Israel Institute of Technology, Israel) 14h40 172 | A complex wavenumber approach to model wave dispersive properties in phononic damped plates Palermo, Antonio (University of Bologna, Italy) [email protected] Marzani, Alessandro (University of Bologna, Italy) [email protected] 15h00 173 | Structronic composite plates based on novel guided wave frequency steerable transducers for aeronautic structures De Marchi, Luca (University of Bologna, Italy) Testoni, Nicola (University of Bologna, Italy) Viola, Erasmo (University of Bologna, Italy) [email protected] Marzani, Alessandro (University of Bologna, Italy) [email protected] 15h20 175 | Numerical simulation of tests for the evaluation of the performance of the reinforced concrete plates strengthening by FRCM Anania, Laura (University of Catania, Italy) [email protected] Badalà, Antonio (University of Catania, Italy) [email protected] D'Agata, Giuseppe (University of Catania, Italy) [email protected] 15h40 90 | Free vibration analysis of rotating FGM beams using the p-FEM Ouissi, Mohammed N. (University of Tlemcen, Algeria) [email protected] Hamza Cherif, Sidi M. (University of Tlemcen, Algeria) [email protected]
23
FRIDAY 11 September Room 6.2
General Session
Chairs: Yoshitake Nishi (Tokai University, Japan) Nechitailo, Nicholas (Naval Surface Warfare Center, USA) 14h00 111 | Adhesion Created and Improved by Safety Electron Beam Irradiation Yoshitake Nishi (Tokai University, Japan) [email protected] Masae Kanda (Tokai University, Japan) [email protected] Chisato Kubo (Tokai University, Japan) Arata Yagi (Tokai University, Japan) Akiko Minegishi (Tokai University, Japan) Ryoh Nomura (Tokai University, Japan) Michael C. Faudree (Tokai University, Japan) 14h20 131 | Anomalous and Unpredictable Deformation of Ordinary Impulsively Loaded Shells, Plates and Beam Nechitailo, Nicholas (Naval Surface Warfare Center, USA) [email protected] 14h40 103 | Influence of locational states of submicron fibers added into matrix on mechanical properties of plain-woven Carbon Fiber Compos Soichiro Kumamoto (Doshisha University, Japan) [email protected] Kazuya Okubo (Doshisha University, Japan) Toru Fujii (Doshisha University, Japan) 15h00 118 | Evaluation of the Dynamic Properties of Composite Laminate under Flexural Vibration Abdelhafid, Rahmane (Constantine 1 University, Algeria) [email protected] Toufik, Benmansour (Constantine 1 University, Algeria) [email protected] Issassfa, Brahim (Constantine 1 University, Algeria) [email protected] 15h20 34 | Experimental behavior of slag concrete-filled steel tubular reinforced with shear connectors Handel, Naoual (University Mouhamed Cherif Messadia, Algeria) [email protected]