soochna 2012 final
TRANSCRIPT
-
7/25/2019 Soochna 2012 Final
1/140
2012 SOOCHNA 2012
Diesel Locomotive Works
OUR LOCOS MOVE THE NATION
Supplements on:
EMDECCCB-II
APCRadial DB grids for WDG5 locomotivesTBU Hybrid Bogie FrameAir Starting System5500 Test Bed New Gear Case Sealing Mechanism Ergonomic Design of Driver Seat Toilet Hotel Load With Siemens Pressed connecting Rods
-
7/25/2019 Soochna 2012 Final
2/140
-
7/25/2019 Soochna 2012 Final
3/140
Index
Section Description Page No.
A1 EMDEC 1 to 13
A2 CCBIII 14 to 18
A3 Auxiliary Power Converter (APC) 19 to 20
A4 Inverters for Auxiliary Machines 21 to 23
A5 Radial DB grids for WDG5 locomotives 24 to 25
A6 TBU 26 to 28
A7 Hybrid Bogie frame for WDG5 29 to 31
A8 Air Starting System32 to 34
A9 Test bed & test procedure of 20710 G3BES engine for
WDG5 (5500 HP) Locomotive35 to 45
A10 New Gear Case Sealing Mechanism for WDG5 46 to 47
A11 Ergonomic Design of driver seat 48 to 49
A12 Toilet 50 to 51
A13 Development of Air conditioning units on Diesel Electric
locomotives
52 to 54
A14 Development of Cab Heaters on Diesel Electric locomotives 55 to 56
A15 Hotel Load With Siemens 57 to 58
A16 Connecting Rod (Press Forging) 59 to 60
B Special supplements on Design Bulletins 61 to 97
C Compendium of failure investigation 98 to 124
D Summary of important change notice 125 to 128
E List of important CPAs (corrective and preventive action)under ISO9001
129 to 130
F List of trial fitments by DLW 131 to 137
-
7/25/2019 Soochna 2012 Final
4/140
P a g e | 1
Section A1
Electro-Motive Diesel
Engine Control (EMDEC)
-
7/25/2019 Soochna 2012 Final
5/140P a g e | 2
EMDEC
The EMDEC system will cover the following topics relevant to EMDEC functions:1. Introduction
2. EUI fuel delivery system
3. Electronic injections system-Fuel components
4. EMDEC Electronic components & Operation
5. Load Control
6. Diagnostic Tools
1. INTRODUCTION & SYSTEM OVERVIEW:
EMDEC is an acronym for the Electro-Motive Diesel Engine Control system.
EMDEC is an electronic engine speed control and fuel management system. It
is designed to provide optimal control of critical turbo charged engine functions
which affect fuel economy, smoke, and emissions. The system also provides
the capability to protect the engine from serious damage resulting from extreme
operating conditions, such as high engine temperatures or low oil pressure.
EMDEC equipped engines utilize an electronic fuel injection (EUI) system
which replaces the Mechanical unit injection system. An EUI Engine equipped
with EMDEC is capable of improved fuel economy and a reduction in certain
type of exhaust emissions due to the real time feedback and immediate
computer response to the fluctuating parameters of an operating engine. This ismade possible by the systems ability to sense changes in engine or ambient
conditions and adjust fuel delivery rates and injection timing to compensate.
This electronically-controlled fuel delivery system is currently installed in 20-710
G3BES engine for WDG5 (5500 HP) DLW make locomotive. With EMDEC
controlled engines, the quantity of fuel injected by the Electronic Unit Injector
(EUI) is determined by its integral solenoid operated poppet valve which is
controlled by the master Electronic Control Module (ECM).
-
7/25/2019 Soochna 2012 Final
6/140P a g e | 3
2. EUI FUEL DELIVERY SYSTEM:
710 Type EUI Fuel Sytem
3. ELECTRONIC INJECTION SYSTEM-FUEL COMPONENTS
The EUIs perform the same functions as the previous systems mechanical unit
injectors (MUIs). They meter, time, pressurize and atomize the fuel. However,
the functions performed by the governor have been taken over by the Engine
EUIHarness
Flexible
Jumper line
EUIEUI installed in 710 Engine
-
7/25/2019 Soochna 2012 Final
7/140P a g e | 4
Control Modules (ECMs). The lay shaft and injector racks have been replaced
by a wiring harness. The helix and barrel assembly of the MUI has been
replaced by a solenoid, and hollow poppet valve located on the new injector.
Currently there is one type of EUI available for all 710 engine applications.
The EUI may be broken down into three basic sections:
Control
High pressure pump
Injector
EUI and MUI Injectors Breakdown of EUI
Fuel Flow through the EUI:
Flow of Fuel through EUI in
De-energized state (no injection)
-
7/25/2019 Soochna 2012 Final
8/140P a g e | 5
Fuel flows from the flexible jumper line to the EUI, entering through its inlet filter
located in the body of the injector. An internals passage directs fuel to the
control portion of the injector, filling the armature chamber below the E coil
stator. The flow of fuel through the armature chamber cools the stator and
armature, also providing lubrication for components. From this chamber, fuel is
allowed to flow through a passage in the body of the injector to the lower fuelchamber.
An additional flow of fuel to the lower chamber is through a passage to the
hollow center of the poppet valve. Fuel flows through the valve into the lower
fuel chamber to provide cooling of the valve. As the fuel enters the lower
chamber, the flows splits, with most of the fuel leaving the injector through the
return passage to the return fuel jumper line. From there it travels through the
return system to the fuel tank.
If the injector is de-energized, the poppet valve is open allowing fuel to flowupwards around it. This fuel travels into a drilled passageway to fill the high
pressure pump chamber below the plunger.
Operation of the EUI:
The functions of the EMDEC electronic unit injector are both electrical and
mechanical. It performs the functions of metering and timing of the fuel supply
in electrically, while the pressurizing and atomizing of the fuel are still done
mechanically.
The metering and timing functions are controlled by the EMDEC systemElectronic Control Modules (ECM) based on inputs received from the
locomotive control computer through an interface, which fire each individual
EUI at a precise point in time for a specific duration. The primary input from the
control computer is throttle position, while other inputs come from various
engine sensors and feedback from the EUI itself. The ECM energizes the
injector solenoid which causes a slight upward movement of the hollow poppet
valve at a synchronized time and duration, based on inputs used to calculate
the next injection event. Spring pressure acts to move the valve downward
when the solenoid de-energizes. The movement of the poppet valve causes thefuel to flow into the injectors fuel delivery and bypass system.
The injector plunger is given a constant stroke reciprocating motion by the
injector cam acting through the rocker arm and plunger follower. The initial
pressurization of approximately 13 790 kPa (2,000 psi) causes the needle valve
inside the injector spray tip to lift. This lifting action allows the fuel to flow
-
7/25/2019 Soochna 2012 Final
9/140P a g e | 6
around the needle valve and through the spray tip where it is atomized into the
cylinder combustion
The timing (duration) of injector plunger stroke is set by an adjusting screw at
the end of the injector rocker arm.
This action is based on the software program contained in the ECMs andinputs into the ECMs such as:
Speed requests from the control system via the interface module.
Timing and speed data from the timing pick-ups.
Engine and ambient conditions from the various EMDEC sensors.
4. EMDEC ELECTRONIC COMPONENTS & OPERATION:
ECMs Interface Module Power Supply
Introduction:The main electrical and electronic components of the EMDEC system are:
1. ECMs (Engine Control Modules):The actual injection control computers.
2. Power Supply:74 VDC to 24 VDC EMDEC power source.
Flow of fuel through EUI
End of in ection
Flow of Fuel through EUI
(During injection)
-
7/25/2019 Soochna 2012 Final
10/140P a g e | 7
3. Interface Module:Communication interface between EMDEC and the main
control system.
4. Sensors: Engine sensors for pressure, temperature and injection
timing/speed inputs.
5. Wire Harness:External, injector, sensor and power.
At the heart of the system are the ECMs or Engine Control Modules thatperform all control functions. The ECMs receive control signals from the main
control system through the interface panel. This panel is part of the power
supply that steps down the 74 VDC input voltage to 24 VDC for use by
EMDEC. Attached to the ECMs are the various sensors used for performance
and protective data, and the injectors themselves.
Engine Control modules (ECMs):
ECM 20-Cyl. EMDEC Locomotive Type SystemThese ECMs are mounted inside E-locker in 20-710 G3BES engine for WDG-5
(5500 HP) DLW make locomotive. The main components of the system are the
engine mounted ECMs. These units are self-contained microprocessors that
operate on 24 VDC. Each ECM has the ability to control up to 8 injectors.
Therefore, the number of ECMs applied depends on the engine configuration
for example:
8-cylinder engine has one ECM.
12-cylinder engine has 2 ECMs (right bank 1 thru 6, left bank 7 thru 12).16-cylinder engine has 2 ECMs (right bank 1 thru 8, left bank 9 thru 16).
20-cylinder engine has 3 ECMs (right bank 3 thru 10, left bank 13 thru 20,
centre 1, 2, 11 and 12).
Physically all ECMs are identical, but the software is different for each unit.
Every application has one ECM designated as a sender (Master or Controlling)
ECM. The software provides the units identity as well as the application specific
operating parameters (speed schedule for example). The sender is responsible
-
7/25/2019 Soochna 2012 Final
11/140P a g e | 8
for primary data processing and overall control of engine functions. The
remaining ECMs carry the designation of receiver (s). In 20-710 G3BES engine
for WDG-5 (5500 HP) DLW make locomotive, three ECMs are available in the
EMDEC and software for each is unique i.e. Sender, Receiver #1 and Receiver
#2 all have different software. Software difference between Receiver #1 and
Receiver #2 is with respect to calibration codes although; there are differentcalibration numbers for each injector.
Receiver ECMs are controlling by the sender ECM, which provides basic
information such as injection pulse width (fuel amount), and base injection
timing. Remember, the number of receiver ECMs depends on the number of
engine cylinders. The software allows for some independent operation of the
unit and engine RPM requests and basic timing feedbacks are fed to the
receiver (s), independent of the sender. This will allow the system to overcome
intermittent communication problems between the sender and receiver (s).
Arrangement:
EMDEC EMDEC installed in E-Locker
The location of the ECMs on the engine will vary depending on application. In
16-cylinder 710 G3B engine for WDG-4 locomotive, ECMs are mounted on the
front camshaft housing cover. The sender will be on the left side of the engine
and the receiver on the right. While for 20-710 G3BES engine on WDG-5 (5500
HP) locomotive, ECMs are mounted on E-locker
Power Supply:
The Power Supply is located in the AC Cabinet towards the rear of the
locomotive. The function of the power supply is to step down and filter the 74
VDC control system voltage to 24 VDC. EMDEC was originally designed for
heavy truck type applications, therefore operates on a system voltage of 24
VDC. The output of the power supply is fed directly to the interface module and
through a power harness, to the engine mounted ECMs.
-
7/25/2019 Soochna 2012 Final
12/140P a g e | 9
Interface Module:
The Interface Module is located in the AC cabinet of the WDG-5 locomotive and
is typically mounted on the side of the power supply. The function of the module
is to translate signals being sent from the control system to EMDEC and data
travelling from EMDEC back to the control system.
Engine speed information is communicated from the control system to the
ECMs through an interface board.
Sensors:
At this point, the system has been supplied with 24 VDC for operation and has
received speed inputs from the control system. Before EMDEC can operate the
injectors, additional information is required such as timing and speed data,
engine performance data and engine protection data. All this information comes
into the ECMs in the form of sensor inputs. The sensors can be broken into
three major groups:
System Sensors for timing and speed information:For timing and speed functions for EMDEC operation, Timing information is
used by the ECMs to determine when to energize the injector solenoids. Speed
information is used to compare actual speed to desired engine speed. Fuel
rates are then adjusted by the ECMs to correct any variation. Unlike other
sensors on the engine, the system sensors (SRS & TRS) are magnetic pickups.
Synchronous Reference Sensor (SRS) - 1 pulse per revolution
Timing Reference Sensor (TRS) 36 pulse per revolution
-
7/25/2019 Soochna 2012 Final
13/140P a g e | 10
Performance Sensors for calculating fuel injector operation:For calculating fuel injector operation by examining the air and fuel
parameters, EMDEC can fine tune injector operation (timing and pulse
width) to maximize fuel economy and minimize exhaust emissions. All
performance sensors are connected and will return a certain feedback to
sender ECM only.
Fuel Pressure Sensor (FPS)
Fuel Temperature Sensor (FTS)
Turbo Boost Air Pressure Sensor (TBS) or Air Box Pressure Sensor
Air Temperature sensor (ATS)
Protective Sensors for monitoring of support systems:
For monitoring of engine support systems, In the event of a system
failure (lube oil, cooling or crankcase ventilation), EMDEC can shutdown the engine to prevent costly component damage.
Air Box Temperature Sensor
Oil Temperature Sensor (OTS)
Oil Pressure Sensor (OPS)
Coolant Pressure Sensor (CPS)
Coolant Temperature Sensor (CTS)
Crankcase Pressure Detector (CCP) or Crankcase Pressure
Sensor (CCP)
Turbocharger Speed
Engine Speed
If a condition is detected, EMDEC will activate a digital alarm output and send
the alarm information via the communication links. Optionally, the system can
be configured to stop the engine as well.
TRS Sensor
SRS Sensor
-
7/25/2019 Soochna 2012 Final
14/140P a g e | 11
5. LOAD CONTROL:
The term load on control refers to the matching of electrical load on the main
generator to engine performance. In one way, this may be considered as
another protective system for the diesel engine. If there is a problem with the
engine that will reduce available horse power, such as plugged air or fuel filters,
it is necessary to reduce the load on the engine to prevent damage to
components or over-fueling leads to unacceptable levels of exhaust emissionsand possible engine damage.
Control of the actual load on the generator, commonly referred to as excitation
level, is the responsibility of the locomotive control system. The injection
system must provide the control system with a feedback that will indicate the
engines ability to maintain speed at the given load level.
Load control with EMDEC protects the diesel engine against overloading and
over fuelling.
The operator establishes a desired power level using the control system. The
control system determines excitation levels and commands to EMDEC,
EMDEC, through the interface module.
Once the ECMs receive the signal from the interface module, this is converted
to a set speed. The ECMs will control the fuel injectors based on sensor inputs,
to maintain actual engine speed at the set speed level.
Turbocharger
Speed
Sockback Filter
Oil Pressure
Turbo Lube Oil
Pressure
Engine Input fuel
Pressure
Engine fuel Input
Temperature
Engine Fuel Filter
Input Pressure
Sensor Location-Fuel Pressure
Sensor Location-
Oil Pressure
Sensor Location-Crankcase Pressure
Engine Input
Fuel Pressure
Engine CoolantOutput Pressure
Engine CoolantOutput Temperature
Engine Oil
Input Temperature Air Box
Air Pressure
Air Box
Temperature
Crankcase
Pressure
Sensor
-
7/25/2019 Soochna 2012 Final
15/140P a g e | 12
Fuel Maps:
Fuel maps are programmed into the ECMs software, that indicate allowable
pulse widths for each throttle position. Remember that the injector pulse widths
refer to the duration of the injection pulse, measured in degrees of crankshaft
rotation. The longer the pulse width, the more fuel is injected into the engines
cylinders.
Typical Fuel Map (for illustration only)
Controlling Engine Speed:
EMDEC works just like a Woodward Governor to control engine speed. If speed
drops, it adds fuel (open the injector pulse widths). If speed rises, it cuts fuel(closes the injector pulse widths). A feedback to the control system is still
required to prevent overfueling. EMDEC will generate a reference signal
proportional to the amount of fuel being consumed.
Control System with EMDEC
-
7/25/2019 Soochna 2012 Final
16/140P a g e | 13
Engine Ratio Signal
The above illustration is shows that example of fuel maps for throttle 5 and throttle 8.
As EMDEC operates the injectors, it generates the Engine Ratio signal. This is the
actual pulse width divided by the maximum pulse width expressed as a percentage.
The Ratio "Engine R is defined as ratio of Actual Fuel used to Maximum amount of
fuel to be used for a particular notch. It is designed to be limited to maximum 87.5%.
Therefore, EMDEC electronic system is much faster and more accurate than the
mechanical system.
6. Diagnostic Tools
To access the EMDEC ECMs
Required for troubleshooting, loading software and injector calibration.
Procedures for using the Win EMMON program with a laptop computer.
WinEMMON (Diagnostic with a laptop PC)
WinEMMON kit is the recommended EMDEC interface tools. WinEMMON is Windows based System.
Following instructions are provided to assist the trouble shooter in using
this tool.
Monitor all sensor inputs to the ECMs
View ECM outputs to the injectors (Pulse width & timing)
View injector response times
Calibrate the injectors
Load ECM software
View & download fault data
This software generates a diagnostic screen and interface protocol on the laptop.
To use the program, it must be loaded into the laptop, the laptop connected to the
EMDEC system through the cable translator assembly and program initiated.
*****
-
7/25/2019 Soochna 2012 Final
17/140P a g e | 14
Section A2
CCB- II
-
7/25/2019 Soochna 2012 Final
18/140
P a g e | 15
CCB-II
CCB-II (IR), an upgraded version, has been used by DLW on WDG5 locomotive.CCB-II (IR) has also been fitted on one WDG4 loco which is based at BGKT shed.The performance of the loco is under monitoring. CCB-II offers certain operational
advantages which are not offered with CCB-1.5. A comparison of the salient featuresof CCB-II & CCB-1.5 is given below:
CCB 1.5 CCB II IR
Valves mounted on both sides ofmanifold
~26 serviceable valves totroubleshoot
No system clock
No flow sensing
No data record with removed valves Interface only to display behind
driver
No crew advisory messaging
Electronic cards in computer cardrack
12 individual electronic card types
SW/HW modifications required foradded safety device interfaces
No pneumatic backup
EEPROM replacement for SWchange
Valves mounted on front of panel only Valves modularized into 6 LRUs
Includes Real Time Clock in EBV
Includes flow sensing. Displayed onFIRE of WDG5
Smart LRUs include logs
Integrated with EMD FIRE screenson WDG5
Includes crew advisory on EBVdisplay
Fully potted electronic modules.
Two node types plus LON Converter Additional safety devices can be
piped to EPCU pipe 3 or 10 withoutSW/HW change
Can be used with Backup DBVs
Flash programmable using PTU
-
7/25/2019 Soochna 2012 Final
19/140
P a g e | 16
A conceptual schematic describing the working of CCB-II is given below:
Communication - Air Brake system with FIRE and EM2000
CCB-II(IR) communicates with LCC (EM2000) & FIRE. Communication taking place
with FIRE is basically only an interface for display of pressures etc. LON generally
handles gauges, self test, and event / fault logs. Functionally the communication is
of non-critical type. Communication occurring on RS485 (between CCB and
EM2000) handles commands for blended brakes, AEB reset, overspeed penalty etc.
This is similar to what is already there on WDG4. CCB-II (IR) has a pneumatic
interface available for use of additional magnet valves for desired penalty
applications, if any, without any need for change in EM2000 software.
Communication linkage is shown below as schematic.
BRAKE PIPE
BRAKE CYLINDER EQUALIZING PIPE (20-PIPE)
BRAKE CYLINDERS
RCP
EBV A
EPCULocomotive I/O
#21 Pipe
CCB II-IR is a modular system with provision for expansion if required.The core system contains 4 major components
LON
LON
EBV BLON
PSJB
-
7/25/2019 Soochna 2012 Final
20/140
P a g e | 17
Fig: Schematic showing communication linkages between CCB-II , LCC & FIRE
Scope of expansion offered by CCB-II(IR) version
EM2000
CCB-2
FIRE
CAN
RS485
LON
Hardwire
MV
RCP
EBV
EPCU
LOCOMOTIVEI/O
Optional expansion modules for increased I/O, blending, screen interface, etc.Expansion modules connect to the system LON.
LON
CoreBrakeSystem
Opt. Interface to EMD FIRE Screen
LON RS422 Module
IntegratedProcessorModule(IPM)
Loco CabDisplay(LCDM)
Relay Interface Module (RIM)
Loco Interface Module(LIM)
Multi Purpose InputOutput Node (MPIO)
LON- RS485 Module
Analog I/O Node (AIO)
OptionalExpansionElements
Second EBV
LON- Ethernet Module
LOCOMOTIVE
Computer
-
7/25/2019 Soochna 2012 Final
21/140
P a g e | 18
The benefits of CCB-II (IR) over the existing CCB-1.5 version are as under:
Simplification of solid-state equipment including the micro-computer to
minimize number of controls.
Improved reliability with increased redundancy
Availability of back-up modes.
Ease of Maintenance (use of Line Replicable Unit approach).
Rationalization & integration of pneumatic components so as to reduce the
number of components/sub-assemblies.
User-settable parameters & compatibility with related third party equipment
*****
EBV- Electronic Brake Valve
The EBV provided in CCB-II version has a
LCD display. The display provides a target
BP value which the crew requests when the
handle is moved. Faults are annunciated on
this LCD screen. Routine advisory
instructions such as penalty reset and
emergency reset are also displayed on this
screen. The EBV communicates with the
Air Brake System through LON network.
This communication is through Optical fiber
in case of CCB-1.5.
EBV mounted on desktop
-
7/25/2019 Soochna 2012 Final
22/140
P a g e | 19
Section A3
Auxiliary Power Converter
(APC)
-
7/25/2019 Soochna 2012 Final
23/140
P a g e | 20
APC- Auxiliary Power Converter
WDG5 Locomotive has been provided with Auxiliary
Power Converter (APC) which replaces the following
equipments: Introduction of APC has eliminated use of items
like Auxiliary Generator, Aux gen drive shaft,
flexible coupling, Aux gen mounting arrangement
& need for adjustment of shaft (radial & facial).
The cases of coupling failure will get completely
eliminated.
Voltage Regulator(in ECC#1)
Battery Charging assembly(in ECC#2)
The above items are being used in WDG4/WDP4B Locomotive. The APC is a
modular unit located on the back inside wall of the electrical locker. Auxiliary Power
Converter fulfills battery charging, companion alternator excitation and control
system 74 VDC requirements. Power to the APC is taken from one of the
Companion Alternator windings. Input to the APC is a three phases, alternating
current from Companion Alternator with both frequency and voltage proportional to
locomotive engine speed ,ranging from 44.4 VAC / 26.7 HZ @ engine idle(200 RPM)
to 200 VAC /120 HZ @ Throttle 8(904 RPM). The APC has provided visual display
on its panel:
The display panel indicators of APC are:
Green control voltage LED: indicates the APC Circuit Breaker is closed and
the control voltage is present.
Green AC voltage LED: 3 phase input from the companion alternator is
present. Green enable LED: EM2000 is not inhibiting the APC.
Green DC voltage LED: the APC is producing an output 72-78 volts dc.
Red Fault LED : Indicates fault in APC
*****
-
7/25/2019 Soochna 2012 Final
24/140
P a g e | 21
Section A4
Inverters for Auxiliary
Machines
-
7/25/2019 Soochna 2012 Final
25/140
P a g e | 22
Inverters for Auxiliary Machines
In WDG5 locomotive Auxiliary inverters for Radiator Cooling
Fans 1 & 2 and Traction Motor Blowers have been provided.
The three Inverters (two for each Radiator Fan and one for
traction motor blower 1 & 2) are located on the back inside
wall of the electrical locker. The three Aux Inverters have
rating of approx 100 KW each. The more advantages of
inverters are:
Greater control precision.
Variable speed control of Auxiliaries Motors. Inverter provides soft start algorithm which start motor at higher volts/hertz
to provide adequate starting torque and quick motor acceleration.
Inverter can operate auxiliary motors at 5-10% higher speed than typical
contactor controlled auxiliary motors on 8th Notch.
At lower notch, inverter can operate auxiliary motors at 20-30% higher
speed than typical contactor controlled auxiliary motors.
Optimum utilization of Engine power which results in saving of energy hence
more power available to traction during off load of Radiator Blower Motors.
Working Principle:
a. Inverter for Tractrion Motor Blowers (Front & Rear) : Based on traction
inverter cooling requirements from phase module and traction motor cooling
requirements from traction motor thermal algorithm, The EM2000 sends request
to Inverters through Controller Area Network (CAN) for sending the frequency
command to the truck blowers for operation. Auxiliary inverter sends statussignals back to LCC over the CAN network. These status signals include the
three motor line currents, DC link voltage, line to line voltage, heartbeat, IGBT
temperature, motor operating frequency, and any fault conditions.
-
7/25/2019 Soochna 2012 Final
26/140
P a g e | 23
b. Inverters for Radiators cooling fans 1 & 2: Based on engine coolant
temperature cooling requirements, The EM2000 send request to Inverters
through Controller Area Network (CAN) for sending the frequency command to
the Radiator fan cooling Motors 1 & 2 for operation. Auxiliary inverter for
Radiator Fan sends status signals back to EM2000 over the CAN network. These
status signals include the three motor line currents, DC link voltage, line to line
voltage heartbeat, IGBT temperature, motor operating frequency, and any fault
conditions.
*****
-
7/25/2019 Soochna 2012 Final
27/140
P a g e | 24
Section A5
Radial DB grids for
WDG5 locomotives
-
7/25/2019 Soochna 2012 Final
28/140
P a g e | 25
Radial DB grids for WDG5 locomotives
Radial design DBR Hatch assembly has been used in WDG5 locomotive, which is
compact and modular in design requiring lesser space. The DB assembly consists of
four resistor, 54 fan and 100HP, 450V, 2000 rpm motor. The grid resistors are
suitable for dissipating 3100 KW power during dynamic braking.The positioning of Radial DBR and compact E-locker has given up the space for
toilet to be accommodated to provide basic amenities to the driver.
PO for 10 sets of Radial DBR was placed on M/s DPG/USA and 01 number to M/s
DRI/Bhopal. The order on DRI/Bhopal is developmental order.
Comparison of DB Hatch Equipment with Radial DBR
Parameters WDG4 WDG5FAN MOTOR ASSEMBLY
Rating of fan motor 36HP 100HP
No. of fan motor Two One
No. of fan blades in eachassembly.
Ten Ten
Voltage 300 VDC 450 VDCCurrent 118A 195 A
RPM 1650 2000
GRIDSNo. of grids Eight Four
Capacity of grids 367.5x8=2940KW 3100 KW
Maximum Grid volt D.C.2700 D.C.2700
Physical arrangement of Grids Box type on top of TCC Radially on top of E locker
Space required for completeassembly
More space is required Less space is required
Position of grids w.r.t. fanassembly
Behind the fan blades In front of fan blade
FITMENTSupplied as Kit Single unitTime required for mountingon loco.
More Less
Weight 1800kg 1400 kg
*****
-
7/25/2019 Soochna 2012 Final
29/140
P a g e | 26
Section A6
Tread brake unit
(TBU)
-
7/25/2019 Soochna 2012 Final
30/140
P a g e | 27
Tread Brake Unit
Tread Brake Units are bogie mounted mechanical devices used to provide braking
force to the locomotive. The brake unit converts pressured air into mechanical
movement and force on the brake shoe against wheel tread. Unitized tread brakes
acting on one composition brake shoe per wheel provide the braking power for the
locomotive. The tread brake units utilize integrated slack adjusters that compensate
the full amount of wheel wear as well as the brake shoe wear.
The unitized pneumatically powered tread brake unit consists of a brake cylinder, a
transmission mechanism and a slack adjuster. The models having an attached
spring actuator can be used both as service brakes and as parking brakes. The
spring actuator is released by compressed air allowing all the parking brakes on the
locomotive to be applied and released centrally from the driver's cab.
The main characteristics of tread Brake Units are:
1 Unitized Tread Brake per wheel with 1 brake head and 1 brake shoe per
wheel. Brake shoe is of K-Type composite material
All units are top mounted allowing easy removal and installation
Parking brakes are provided in end axles of each bogie
The units on the middle axle of each bogie are flexible type
Integrated slack adjuster to compensate for whole brake shoe and wheel
wear.
Integrated spring applied and air released parking brake
There are six brake units per truck, two of which are equipped with the spring
actuated parking brake, and are provided on the same side of end axles of each
-
7/25/2019 Soochna 2012 Final
31/140
P a g e | 28
bogie. Block brake units designed for use as service brakes contain the following
assemblies:
Brake cylinder and piston.
Adjuster mechanism providing automatic adjustment in response to brake
block and wheel tread wear. Single acting slack adjuster which, after one brake application, automatically
corrects the increasing clearance due to wear.
Reset mechanism for resetting the spindle after brake block replacement.
All units are mounted behind the axle.
Parking brake units are at non-gear side of the end axles.
Brake units for use as service and parking brakes are equipped additionally with a
spring actuator. When the spring parking brake is applied, the force of the actuator
springs acts on the piston in the block brake unit's brake cylinder through the cone
coupling, nut and the spindle. The spring actuator is equipped with a manual
emergency release allowing the parking brakes of parked vehicles to be released
without compressed air. To release the brakes, the operator must pull out the tappet
by hand.
Mid axle flexible unit
End axle gear side non-parking brake unit End axle non-gear side parking brake unit*****
-
7/25/2019 Soochna 2012 Final
32/140
P a g e | 29
Section A7
Hybrid Bogie frame
for WDG5
-
7/25/2019 Soochna 2012 Final
33/140
P a g e | 30
Hybrid Bogie Frame
The WDG5 locomotive is equipped with two High Tensile Cast Fabricated
(HTCF) bogie frame assemblies. The bogie frames support the weight of the
locomotive and provide the means for transmission of power to the rails. The
rigid steel fabricated frame, utilizes a bolster-less secondary suspension system.
All longitudinal traction and braking loads are transferred from the bogie
assembly to the locomotive under-frame through the car-body linkage system.
The bogie is designed to provide high reliability, longer overhaul cycle and
extended maintenance intervals.
Design features
1. This is a hybrid bogie frame consisting of fabricated longitudinal beams &
cast transoms (cross members). Pivot transom is a fully casting part while
other middle & end transoms are partially cast & welded with longitudinal
beams during fabrication.
2. All structural components are made from High Strength Low Alloy steel
EMS 93 with yield strength of 345 MPa (50KSI) or equivalent cast steel
EMS26.
3. Any weld joint to the cast steel components requires preheating to 80C.
4. The manufacturing technique follows the conventional sub-assembly
structure with side frames and transoms.
5. Stress relievel at a temperature between 595an d 650C.
6. Majority of the features are machined after weld assembly. Some brackets
are pre-machined and added after stress relieving.
BOGIE FRAME
CAST TRANSOM BRACKET
-
7/25/2019 Soochna 2012 Final
34/140
P a g e | 31
Advantages of bogie design for WDG5 Locomotive
Light weight design: Weight savings and better dynamic performance.
Ease of assembly: Less work for unitized brake application. Bushings are notpressed in the bogie frame and bearing adapters.
Maintenance improvements: Reduced labor for unitized brake application andreplacement; replacing traction rod bushing can be done at bench operation; noneed for blocking to lift locomotive.
Performance enhancement: Better ride performance and higher stabilityallowing for potential high speed passenger locomotive application improvedtraction motor ventilation from fixed-fixed air duct arrangement.
Enhanced reliability: Lower track induced accelerations help to reducecomponents failures caused by vibration.
Adaptability to WDG4 locomotive: Minimum modifications
Weight comparison of WDG5 & WDG4 Bogies (excluding wheel Axlecombos)
Sl.No.
Description of item WDG5Weight inKgs
WDG4Weight inKgs
1 Bogie Frame 3700 50002 Bearing adapters, primary
suspension & Tractionrods
2000 1825
3 Secondary suspension 450 4004 Brake system 400 7005 Nose link & Air ducts 200 2506 Car body linkage 200 1607 Misc. item 200 280
Total 7150 9215
*****
-
7/25/2019 Soochna 2012 Final
35/140
P a g e | 32
Section A8
Air Starting System
-
7/25/2019 Soochna 2012 Final
36/140
P a g e | 33
Air starter System
WDG5 Air Start System Schematic
WDG5 Locomotive is provided with Air Motors which replaces the DC starter
motors used in WDG4/WDP4B Locomotive.
Dual Air Starter System (Motors) Dual electrical start System (Motors)
(WDG5 Locomotive) (WDG4/WDP4B Locomotive)
The engine air starting motor, consists of an air driven turbine wheel assembly
positioned in a cylindrical housing, a planet type reduction gear train, and a
clutch drive, all of which are supported by ball bearings. Air striking the turbine
wheel rotates the Planet gear set which turns an offset shaft through an
-
7/25/2019 Soochna 2012 Final
37/140
P a g e | 34
intermediate pinion and drive gear set which turns the clutch drive. The clutch
driven pinion gear mesh with the engine ring gear and cranks the engine.
The engine starting system consists of dual Air starting motors and associated with
air piping and controls. The dual air starting motors are mounted one above the
other and bolted to bracket assemblies which, in turn, are attached to the rear end
plate at the sides of the engine. A flywheel pointer is bolted on the face of thebracket assembly.
Air Starter Operation
1. Two starts possible with SR pressure as less as 95 psi.
2. With start sequence initiated, the Magnet Valve gets energized , pushing
the air from starter reservoir to a starter motor (pushing out the pinion) and
then to the second air starter motor (pushing out the pinion) , comes back
to operate the relay valves which in turn allows bulk air to flow through the
strainers to the starter motors for rotational motion.
3. When EM2000 senses that the engine has achieved a certain RPM, it de-
energizes the Magnet valve, which in turn allows the air trapped in the
pinion cylinders to drain and also the air operating the relay valves to drain
through the magnet valve exhaust post. The pinion retracts and the
contact between the ring gear and pinion and therefore the start sequence
is terminated.
4. The start reservoir can also be charged by another loco with MREP
connected or by shop air through MREP connection.
5. Auxiliary compressor takes about 45 minutes to completely fill the starter
reservoir (45000 cuin). It is not intelligent. SRPT is read by EM2000.
6. The leakage rate in the starter circuit should not exceed one psi/24 hour.
The drain valve port of the starter reservoir is to be used to fix in the
pressure gauge. With the charging source isolated, the drop in the
pressure is read on the pressure gauge.
The cut-out cock in the air starter circuit works as a start fuse. It is to be used
when the loco is in shop for attention (to eliminate any chance of cranking )
****
-
7/25/2019 Soochna 2012 Final
38/140
P a g e | 35
Section A9Test bed &test procedure
of 20-710 G3-BES engine
for WDG-5 (5500 HP)
-
7/25/2019 Soochna 2012 Final
39/140
P a g e | 36
TEST BED & TEST PROCEDURE OF 20-710 G3BES ENGINE FORWDG-5 (5500 HP) LOCOMOTIVE
Block Diagram of Test Bed
Typical test setup used for testing of 20-710 G3BES engine in EMD test cell is as
under:
Engine and alternator are mounted on different dolleys and coupled with a
coupling.
Alternator and coupling are mounted on a fixed stand and having the following
arrangement.
Separate duct and blower are provided for alternator cooling.
Two pneumatic motors each side for cranking.
Typical Test Bed Arrangement
-
7/25/2019 Soochna 2012 Final
40/140
P a g e | 37
Vulcan coupling and Amerigear coupling for taking misalignment.
Engine is mounted on a movable dolly in which mounting pads are provided for
12 Cyl, 16 Cyl, and 20 Cyl. Engines. Engines are mounted on the dolly with the
help of doweling arrangement. Dolly is self driven by pneumatic motors.
Separate duct
Pneumatic
motor
-
7/25/2019 Soochna 2012 Final
41/140
P a g e | 38
Separate stations out side test bed for water, fuel and lube oil for pre circulation
for water, fuel and lube oil.
Separate station out side test bed for engine consumables
In test bed piping fuel oil is designed in such a manner that all 12 cyl, 16 cyl and
20 cyl engines can be tested. Separate piping for water and lube oil are also
provided.
Fuel oil piping Water Piping Lube oil Piping
Test bed of EMD is approximate 1.5 times more than the DLW test bed and
flexible side stands can be pushed back. In test bed control room, visual display
is provided for chimney to monitor the exhaust smoke level. There are separate
visual computer screen for EMDEC data (in case of Electronic fuel injectors) and
test bed results in Test bed control room.
-
7/25/2019 Soochna 2012 Final
42/140
P a g e | 39
EMD TEST BED DLW TEST BED
There are fixed ducting for Turbo Supercharger IN and OUT.
ECMs have been mounted on wall of Test Bed. EMD test bed is compatible of testing for MUI and EUI engine.
Fixed ducting for air inlet to turbo for different
types of engine ECMs mounted on wall
There are separate screen provided for display EMDEC parameters, test bed
parameters and display of smoke from chimney.
Computer display of EMDEC
data system
Computer display of system Visual display chimney in
EMD Test Bed
Engine washing arrangement is given on test bed.
MOVEABLE SIDE STAND
Exhaust
Out
-
7/25/2019 Soochna 2012 Final
43/140
P a g e | 40
The cooling system in lube oil circuit is still working after testing of engine also to
cool the engine.
TEST BED SENSOR EMDEC SENSORS
1 Governor oil pressure/Lub oil returnpressure
2 Turbo air inlet temperature sensor
3 Crank case vacuum sensor
4 Water pump left bank pressure
5 Air box temperature
6 Lub oil temperature
7 Lub oil compressor Bearing Pressure
8 SRS & TRS sensor
9 Fuel temperature sensor
10 Water pump right bank pressure11 Air box temperature
12 Fuel pressure
Routine Test Procedure for 710 G3B ES Engines
All Engines are to be tested as follows:
1. Preset Inspections:
a) Pressure test cooling systems using house air static pressure applied for aminimum of 15 minutes. If repairs are required, repeat this test after
repairs have been completed.
b) Pressure test fuel filter by pass valves on applicable MUI engines at 60
PSI.
c) Pressure test fuel systems by applying tank farm fuel system thoroughly
for leaks and make all necessary corrections. If repairs are required,
repeat this test after repairs have been completed.
d) Check and fill governors on engines so equipped to the top of the sight
glass with fresh oil.
e) Fill oil bath air filters on test cells when required to the fuel level markprelube engines with lubricating oil using an external pump connected to
the lube oil oil pump discharge elbow. While oil pressure is applied, bar
the engine over on complete revolution and then check all bearings for
appropriate, restricted, or excessive.
1 Governor oil pressure/Lubeoil return pressure (X)
2 Lube oil compressor BearingPressure (Y)
3 Main lube oil pressuresensor
4 Piston cooling pipe pressure
5 Turbo RPM sensor
6 Water pump right bankpressure
7 Water pump left bankpressure
8 Crank case vacuum sensor
-
7/25/2019 Soochna 2012 Final
44/140
P a g e | 41
f) EUI Application:
I. On early 710 EUI engines equipped with fuel filter manifolds utilizing
sight glasses and dual fuel return lines, test fuel filter by pass valves
at 100 PSI. This test cannot be performed on and does not apply to
later 710 EUI engines with fuel filter manifolds utilizing a single fuel
return line and no sight glasses.II. Turn the test cell fuel pump pressure switch to higher pressure
setting.
III. Check for fuel leaks in cold plates and hoses.
IV. With the control console in the off position, connect controllers to the
test stand.
V. Connect the water discharge pressure sensor in the test cell.
2. Initial Test Cell Inspection:
a) Crankshaft end thrust must be within 0.008 to 0.021 inches.b) Engine cooling water must be treated per appropriate recommended
practices.
c) Lube oil addition and initial Engine charging:
II. Engine lube oil must confirm EMD fuel specifications.
III. Oil may be reused for multiple engine tests provided that
contamination is monitored and controlled through periodic analyses
conducted by the Engineering Petroleum Laboratory.
IV. All Lube oil after prelubing is to be added through strainer housing.
d) Loosen compression relief valves and blow out engines before starting.
e) Program EUI Controllers with the correct calibrations..
3. Break In Test Instructions:
a) The soak back pump on turbocharged engines must run and generate
pressure for a minimum of 10 minutes before each engine start. The soak
back pump must also run and generate at least 5 PSI pressure measured
at the turbocharger compressor bearing for a minimum of 20 minutes after
each engine shut down. The engine may be immediately restarted
anytime during this twenty minute shutdown period.b) The first two steps in the Break-in Schedule are to be made with the top
deck open. During these run checks for leaks, lubrication, and operation of
valves, injectors, rocker arms and camshafts.
Rocker arm cam follower rollers must not overhang either edge of their
respective camshaft lobe by more than 1/16 when the roller is located on
the lift portion of the cam lobe and off the base circle, and as measured
from the side face of the roller to the side face of the cam lobe.
-
7/25/2019 Soochna 2012 Final
45/140
P a g e | 42
c) Visually check for exhaust manifold leaks and check the turbocharger for
external oil leaks, air leaks and abnormal or excessive noise.
d) Check that oil is visible in the governor sight glass on engines so equipped
during the entire break-in- run.
e) At 640-680 engine RPM, the oil pressure drop across the turbocharger
must not be more than 30 PSI nor less than 5 PSI at a 150F- 180Fengine oil in temperature.
This pressure drop specification checks for excess lube oil flow in the
turbocharger and represent the difference between the rear end oil
pressure, measured at the governor line connection point to the cross over
manifold downstream of the turbocharger filter on MUI engines or at the
filter discharge side of the turbocharger filter housing on EUI equipped
engines and oil pressure at the turbocharger compressor bearing.
f) Perform vibration testing as per ETI 1579.
g) Break in Run schedules
These schedules are designed to bring engines to full load quickly to
condition newly manufactured surfaces for rated power operation. Break
in runs also facilitate selected initial and / or assembly defect detection
and correction.
h) Perform the following inspections at the end of the first hour at full load
and full speed:
I. With Hot Oil, bring the engine to IDLE and immediately record the
Oil-in Temperature and the engine rear end oil pressure measured
downstream from the turbo oil filter i.e the supply pressure to thegovernor on engines so equipped. Oil pressure at this point must be
15 PSI minimum for turbocharged engines.
II. On electronically controlled (EMDEC equipped) 710 series
turbocharged engines, engine rear end oil pressure at 200 rpm (low
idle) is to be recorded. Bring engine speed to 200 rpm with no load
applied. Control oil into engine temperature with in range of 180F to
190F. After 5 minutes, record rear end oil pressur e (EMDEC oil
pressure sensor line). Oil pressure must be above 8 PSI.
III. A turbocharger Run Down test must be performed on all
turbocharged engines.IV. On EUI engines check operation of the engine low water protector
function by disconnecting the sensor(s) at the water pump
discharge(s).
-
7/25/2019 Soochna 2012 Final
46/140
P a g e | 43
i) Full load Operating limits
710 Engines:
710G3
Fuel return Manifold Pressure minimum (psi) 10
Fuel return Manifold Pressure Maximum (psi) N/A
Rear End Oil pressure @ 180F minimum (psi) * 72 **Main lube oil In pressure @ 180F minimum (psi) * N/A
Oil Inlet Temperature maximum (F) 200
Oil Pan Depression minimum ( H2O negative) -3
Oil Pan Depression maximum ( H2O negative) -8
Water Inlet Temperature minimum/ maximum (F) 150 /180
Air Inlet Temperature minimum (F) 0
(*) Minimum oil pressure is reduced 6 PSI for each 10increase in oil
in temperature above 170F and increased 6 PSI for each 10 F
below 170F oil in temperature. For the 710 the max imumdifference in pressure across the engine (main lube vs. rear-end) is
not to exceed 28 PSI.
(**) 67 PSI for engines rated at 750 RPM or lower.
4. Final Test Inspection:
a) Pressure test cooling systems using 20 psi air pressure over water for a
minimum of 15 minutes. Be sure to check for water pump leaks during this
test. No water leaks are allowed during this test. Once this test is
completed, use house air static pressure over water for minimum of one-
half hour. No water leaks are allowed during this test. Disregard pump
seal leakage during this test. This water test must be repeated if any leak
repairs are made.
b) Pressure test fuel systems by applying appropriate static air pressure to
the fuel systems when fully charged with fuel.
I. Use 60 PSI for engines equipped with sight glasses and 90 PSI for
engines utilizing a single return line and no sight glasses. NOTE: Do
not test engines equipped with fuel sight glasses at 90 PSI as the
glass might fracture.
II. Monitor the static pressure loss with 0-100 PSI gauge for 15 minutes.For pressure losses of 4 PSI or greater, check the fuel system
thoroughly for leaks and make all necessary corrections.
This static pressure test may result in fuel leakage around injector
racks on MUI injectors or around plunger bores on EUI injectors.
Although such leakage under these test conditions is not detrimental,
it may cause sufficient pressure loss to fail the leak down test.
-
7/25/2019 Soochna 2012 Final
47/140
P a g e | 44
Engines having leakage only occurring at injector racks or around
plungers may be accepted after thorough checking.
III. This pressure test must be repeated if any leak repairs are made.
c) Top deck and Power assembly Inspections: Visually inspect the top decks,
Air boxes, after cooler cores, crankcase weld seams, piston rings, cylinder
liner bores and the Top of all pistons. Remove and replace all scuffed orscored liners. Removal of scratched liners will be left to the discretion of
the test department supervision.
d) Check turbochargers for external oil leaks and compressor section oil
leaks as evidence by oil at the air discharge flange and / or by oil coming
through the after cooler cores.
e) Check turbocharger exhaust duct interiors for evidence of internal oil
leaks.
Notch Wise Load
Notch 5500 HP Engine BHP (AAR) Duration
RPM BSFC (gm/bhp-
hr)
1 269 200 220 10 Minute
2 343 175 750 10 Min.
3 490 164 1450 10 Min.
4 568 162 2350 10 Min.
5 651 160.5 2800 10 Min.
6 729 155 3950 10 Min.7 820 153.5 4900 10 Min.
8 904 154 5500 10 Min.
5. Post Test Inspections:
a) Re measure the crank shaft end thrust. Do not accept any engine with
more than a 0.005 increase over the original crankshaft end thrust.
b) Retighten fasteners as specified in TO RECOMMENDED TORQUE
VALUES.
c) Perform a lead check to measure the piston- tocylinder head clearances
on all power assemblies.
Maximum lead thickness : 0.068
Minimum lead thickness : 0.020
Do not average measurement. Maximum difference between lead
thicknesses at opposite sides of an individual piston: 0.005.
d) Check at least one lower main bearing on each engine.
1. For all 20 cylinder engines, drop # 2 & #8 lower bearings.
-
7/25/2019 Soochna 2012 Final
48/140
P a g e | 45
2. If handing damages are found with no other issues, change those
bearings with new.
3. If dirt scratches are with in acceptable limit, re-use both # 2 & #8
bearings.
4. If one bearing is with in acceptable limit and the other bearing
unacceptable then replace the damaged bearing with new and re-usethe good bearing in corresponding locations.
5. If both bearings are acceptable, notify the inspector and contact
engineering for further disposition.
e) Make a visual Inspection of all connecting Rod bearings for toe and heel
wear.
f) Monitor Critical fasteners as specified in TO RECOMMENDED TORQUE
VALUES on all engines.
1. Record the location of all rod-to-pin bolts that move during retorquing.
2. Check cylinder head crab nut tightness at all locations.
*****
-
7/25/2019 Soochna 2012 Final
49/140
P a g e | 46
Section A10
New gear case sealing
mechanism for WDG5
-
7/25/2019 Soochna 2012 Final
50/140
P a g e | 47
Gear Case Sealing Arrangement
The Gear case sealing arrangement adopted in WDG5 is different from that used in
WDG4/P4B/P4D locomotives. While the sealing arrangement used in
WDG4/P4B/P4D locomotives uses metal tongue in groove static seal design, the
one used in WDG5 uses plastic tongue in groove static seal design. The details of
both the arrangements have been shown below for better appreciation of the
advantages of G5 gear case sealing arrangement as compared to the G4 design of
gear case sealing arrangement.
Considering the efficacy of design of G5 gear case sealing arrangement, thefeasibility of implementing this design for gear case sealing in WDG4/P4B/P4D locosis being examined.
*****
-
7/25/2019 Soochna 2012 Final
51/140
P a g e | 48
Section A11
Ergonomic design
of driver seat
-
7/25/2019 Soochna 2012 Final
52/140
P a g e | 49
Ergonomic design of driver seat
Based on the feedback from zonal railways on the quality of driver seats being used
in manufacture of WDG4/P4B/P4D, a detailed market survey was conducted to
identify a standard product having proven reliability in the working environment
which is similar to the work environment from the point of view of inertia loads, shockloads, maneuverability & adjustments required for ergonomic posture while working.
A standard driver seat which is being used in heavy earth moving equipments
(JCBs) has been identified and trial fitments of the same have already been done in
a WDG4, WDG5 and Sri-lanka locomotives. This seat has vertical adjustment, back-
rest tilt arrangement, longitudinal slide arrangement and 360 degrees rotational
freedom with 4 stops at 90 deg each. A proposal for procurement of 30 more loco
sets of this design of Drivers seat has been initiated for use as a pilot project before
proliferating this design on a larger scale. The Driver seat model details are as
under:
Manufacturer: M/s. Majestic Seats (India) / Faridabad
Model No: MS-200
(Exhibit The driver seat displayed in the above photograph is the JCB (MS-200
model) seat fitted in WDG5 locomotive cab)
*****
-
7/25/2019 Soochna 2012 Final
53/140
P a g e | 50
Section A12
Toilet
-
7/25/2019 Soochna 2012 Final
54/140
P a g e | 51
TOILET
WDG5 is the only locomotive on Indian railways to have on-board toilet facility for
loco crew. The toilet module is equipped with a stainless steel urinal pot,
stainless steel wash basin, air circulating and an exhaust fan, light, soap
dispenser and a stainless steel hanger. The access to the toilet is from the left
side footplate of the locomotive. A water storage tank of 200 liters capacity is
located above the toilet module with a water filling arrangement on the loco right
bottom side.
The Toilet Cabinet is so designed that it has good hygienic condition & proper
ventilation easy to clean, easy to maintain& repair. It has been designed
ergonomically to provide comfortable entry & exit.
*****
-
7/25/2019 Soochna 2012 Final
55/140
P a g e | 52
Section A13
Development of Air
conditioning units on Diesel
Electric locomotives
-
7/25/2019 Soochna 2012 Final
56/140
P a g e | 53
Development of Air conditioning units on DieselElectric locomotives
Compact air conditioning unit fitted on loco no. 40070
Provision of air conditioning on EMD locomotives was started in 2004 with
placement of two developmental purchase orders on M/s Sidwal and M/s Fedders
Lloyed to DLW specification no. WDG-4/EL/PS/14. The AC supplied had separate
inverters and air conditioning units. 09 units supplied by M/s Sidwal were fitted on
locomotives however these did not perform well in field because of various problems
as such were removed from locomotives. These units were bulky, were protruding
inside cab, thereby reducing head space and were causing difficulty in accessing
control compartment also.
Further, RB issued directives regarding provisioning of air conditioner on
diesel electric loco cabs vide their letter no. 2000/M(L)/466/9 dated 23.07.07.
Considering experiences of earlier units, RDSO prepared a new specification
for air conditioning units with compact size and inbuilt inverter. RDSO defined
eligibility criteria in clause 16.3 of this specification, which reads as As a pre-
qualification criteria, the successful tenderer should have supplied same or
similar design of modular AC unit (with built in Inverter) for at least 200
locomotives. The units should haveworked on locomotives satisfactorily for
at least 3 years. The tenderer shall submit the details of AC units supplied for
locomotive applications. This clause was included to procure this item form an
established source to prove out the concept on theDiesel Electric locomotives.
-
7/25/2019 Soochna 2012 Final
57/140
P a g e | 54
Model of compact air conditioning unit fitted on loco
A PO no. 091080010.11111254 dated 12.01.2011 for 05 nos. of AC units was
placed on M/s DPG/USA. So far 02 units have been fitted on locomotive. One is on
WDP4B locomotive no. 40070 and other on first WDG5 locomotive number 50001.
Purchase order for supply of 16 sets AC on M/s DPG/USA was also placed and 02
sets each on M/s Lloyed Electrics & Engineering Limited/Bhiwadi, M/s DRI/Bhopaland M/s Subros Limited/Noida was placed as developmental order.
DLW is planning to fit AC unit in Dual Cab locomotive. Proto type fitment of air
conditioners in first dual cab locomotive is planned to be made in 2012-13. Design of
rear cab has already modified to accommodate Air condoning unit:
Existing Rear Cab Modified Rear Cab
*****
-
7/25/2019 Soochna 2012 Final
58/140
P a g e | 55
Section A14
Development of Cab Heaters on
Diesel Electric locomotives
-
7/25/2019 Soochna 2012 Final
59/140
P a g e | 56
Development of Cab Heaters on Diesel Electriclocomotives
Diesel locomotives are operating in extreme weather condition in Indian Railways
which include extreme cold conditions. These causes extremely uncomfortable
situation for loco crew as there are no heating arrangement provided on dieselelectric locomotives. Considering above fact, DLW took initiative to develop cab
heater system for diesel electric locomotive.
DLW specification no. WDG4/EL/PS/29 (Rev R0) for cab heaters is so designed that
developed product can be used in both EMD and Alco locomotives. It can easily be
retrofitted in existing locomotives in field. This would be very useful for retro fitment
purpose.
Cab heater fitted on loco
A developmental proposal for procurement of 20 cab heaters was initiated and
tender no. 061180030 opened on 21.04.2011. PO no.061180030.11280734 dated
29.06.2011 on M/s TOPGRIP Instruments Company/Kolkata for 15 nos., PO no.061180030.11280736 dated 04.08.2011 on M/s Elecos/Kolkata for 03 nos. and PO
no. 061180030.11280735 dated 22.07.2011 on Escorts/Faridabad for 02 nos. was
placed.
15 nos. of cab heater system supplied by M/s Topgrip are fitted on locomotives and
dispatched to various sheds in the months of Dec 11 and Jan 12
The cab heater developed having total 1.5 KW of heating capacity and two blowers
at either end to blow hot air. These blowers are driven by rugged design 3 phaseinduction motor. The complete unit is modular in design, housing all accessories
such as heating element, Blower and motor, Inverter, fuses, Circuit breaker, switch
etc. The Power is fed from auxiliary generator rectified output instead of battery to
avoid discharging of battery.
*****
-
7/25/2019 Soochna 2012 Final
60/140
P a g e | 57
Section A15
Hotel Load
-
7/25/2019 Soochna 2012 Final
61/140
P a g e | 58
Hotel Load With Siemens
DLW has placed PO No 090980180.11289186 dt 27.01.2011 on M/s Siemens for
supply of 8 nos AC-AC traction system for WDP4B locomotive with integrated
Hotel Load Inverter module and Distributed Power System as per RDSO Spec
no.MP.0.24.00.43 (Rev.02) July, 2009. The Hotel Load supply contains the
followings additional items with AC-AC traction system: Hotel Load Inverter resides in Traction Control Cabinet (TCC).
Modified ECC#1 & 2
Hotel Load Transformer.
Expansion tank for Transformer.
Oil Cooler for transformer.
Feeder contactor Box(ECC#4)
The advantages of Hotel load with Siemens system in compare to other
manufacturer are as under:
Consume less space as Hotel Load Inverter resides in TCC cabinet.
Hotel Load Transformer provides following advantages
Isolation of Power source
Act as a filter to reduce the harmonics and transients.
The first prototype Hotel Load system of Siemens make is expected to be
manufactured in August2012.
ECC#4
Transformer
-
7/25/2019 Soochna 2012 Final
62/140
P a g e | 59
Section A16
Connecting Rod (Press-
Forging)
-
7/25/2019 Soochna 2012 Final
63/140
P a g e | 60
Connecting Rod (Press-Forging)
Introduction:Press forging method uses a slow squeezing action of a press to transfer a
great amount of compressive force to the work piece. This way it differs from
the hammer forging operation, where most of the energy is absorbed by themachine and foundation. In comparison to hammer forging, closer tolerances
can be achieved in Press Forging. Press forging is economical for mass
production. Connecting Rod Cap integral with Rod for ALCO loco is being
manufactured by Press forge process in two strokes with one heat.
Advantage:
The press-forged design of connecting rod cap integral with rod will bring
significant benefits:
The connecting rods are manufactured by press forging so as to
eliminate / reduce the operation of weight removal during machining on
the web.
The elimination of milling operation on the web portion will eliminate
chances of stress raisers being generated which are a potential cause
of connecting rod breakage.
No chance of weakening of web thickness at gun drill hole location due
to excess material removal on the web by milling machining.
Better Grains flow lines achieved by press forging.
Better mechanical properties like UTS, RA, E, Izod & Hardness meet
by press forging.
Cut Section Showing Grain-Flow
-
7/25/2019 Soochna 2012 Final
64/140
Section B
Compendium of failure
investigations
Page | 61
-
7/25/2019 Soochna 2012 Final
65/140
Page | 62
AN INTRODUCTION TO DESIGN BULLETINS
Every knowledge based organization has considerable tacit
based knowledge resident with the individuals who have
been part of the problem solving process. Unfortunately,
with the change of roles, this knowledge tends to be lost to
the organization.
Design Bulletin aims to capture and embed this tacitknowledge in the organization knowledge domain. The
bulletin, therefore, not only provides the solution but also
the process. Since the solution may involve action by
multiple agencies, the bulletin provides a structure to the
role of each agency for achieving the solution.
First Design Bulletin was issued on 04.06.2010 and till date35 bulletins have already been issued. A compilation of 14
nos bulletins has been included in this issue of Soochna.
The design bulletins have also been posted on DLW web
site for a wider footprint to the solutions. Also since most of
the bulletins are related to the field problems, it will enable
faster dissemination to the customer.
-
7/25/2019 Soochna 2012 Final
66/140
Page | 63
Index
SNDesign Bulletin No. Subject Page No.
1 DB/02/2011/03Swollen perforated sheet around cab light
eject the cab light
64 to 65
2 DB/02/2011/10Problem of breakage of dead lever assembly
& slack adjuster of EMD locomotives
66 to 68
3 DB/01/2011/10Repair of longitudinal cracks in airbox
channels.
69 to 71
4 DB/01/2011/12Failures of Bypass sight glass bowl in
spinon Fuel filter assembly
72 to 75
5 DB/01/2011/13Fitment procedure of Air Duct assembly LB
& RB
76 to 78
6 DB/01/2011/14Load control /regulation (LR activation) in
WDG4/P4B.
79
7 DB/01/2012/15Modified inspection procedure of Air Duct
assembly LB & RB
80 to 84
8 DB/01/2012/16Provision of chamfer in Alco M.B.
Cap(Inter) to PL No.10142034
85
9 DB/03/2011/02
Issue of failure of locomotive No.WDP4B
40021 due to abnormal operation of PCS
circuit.
86 to 87
10 DB/03/2012/01
Issue of failure of Amphenol plug of engine
governor (Woodward) in HHP
Locomotives.
88 to 89
11 DB/03/2012/02Use of additional horn button switch for
assistant loco pilot in WDG4/WDP4B
90
12 DB/02/2012/02 Infringement of dust bin blower 91 to 92
13 DB/02/2012/03 Problem of side bearer plate 93 to 94
14 DB/02/2012/04Problem of wire rope sling fouling with
projected portion of underframe
95 to 97
-
7/25/2019 Soochna 2012 Final
67/140
Page|64
-
7/25/2019 Soochna 2012 Final
68/140
Page|65
-
7/25/2019 Soochna 2012 Final
69/140
Page|66
-
7/25/2019 Soochna 2012 Final
70/140
Page|67
-
7/25/2019 Soochna 2012 Final
71/140
Page|68
-
7/25/2019 Soochna 2012 Final
72/140
Page|69
-
7/25/2019 Soochna 2012 Final
73/140
Page|70
-
7/25/2019 Soochna 2012 Final
74/140
Page|71
-
7/25/2019 Soochna 2012 Final
75/140
Page|72
-
7/25/2019 Soochna 2012 Final
76/140
Page|73
-
7/25/2019 Soochna 2012 Final
77/140
Page|74
-
7/25/2019 Soochna 2012 Final
78/140
Page|75
-
7/25/2019 Soochna 2012 Final
79/140
Page|76
-
7/25/2019 Soochna 2012 Final
80/140
Page|77
-
7/25/2019 Soochna 2012 Final
81/140
Page|78
-
7/25/2019 Soochna 2012 Final
82/140
Page|79
-
7/25/2019 Soochna 2012 Final
83/140
0 1 2 3 4 5 6 7 40 0 7 8 7 9 2 7
1 1 1
1 1 1
0 5 0 0 0 0
0
Page|80
-
7/25/2019 Soochna 2012 Final
84/140
0 1 2 3 4 5 2 6 7 5 8 9 9 3 2 6 8 7
2 8 6 54 7 8 5
0 1 7 8 6 5 2 6 3 9 2 8 6 5 4 7 8 52 5 9 3 9 9 9 5 3 9 7 8 9 5 8 6 5 5 5
4 3 3 2 8 4
0 1 2 3 4 5 2 6 7 8 4 9 3 9 3 2 7 3 6 8 3 9
0 5 6 9 3 8 4 5 5 5 95 9 9 5 3 9 7 8 9 5 8 6 53 2 6 8 9 2 8 6 54 7 8 5 7 7 5 2 8 5 0 5 6 9 3 8 2 5 9 5 5 5 5 9 2 3 5 7 8 9 5 8 6 53 2 6 8 9 5 9 9 5 3 9 7 8 9 5 8 6 5 8 7 9 6 8 3 2 5 2 9 5 2 5 8 5 5 54 3 3 2 8 4 0 5 6 9 3 6 5 9 5 2 8 9 6 53 2 3 5 7 8 9 5 2 3 5 9 9 5 3 9 7 8 9 5 8 6 5 8 7 9 6 8 3 2 5 2 9 5 2 5 8 5 5 8 2 5 5 9 3 8 2 5 9 5 3 9 9 5 7 8 9 5 8 6 58 9 8 9 7 53 2 3 3 9 7 8 9 5 8 6 5
8 9 2 5 9 2 5 2 5
0 2 8 6 54 7 8 5
0 2 8 2 5
0 7 7 5 2 8 5
0 9 7 5 4 2 3 5 6 3 2
0 5 6 9 3 8 2 5 9 5 5 5 5 95 9 9 5 7 8 9 5 8 6 53 2 6 8 9 5 2 6 3 3 7 5 2 7 8 9 5 8 6 5 6 5 6 5 2 8 2 5 7 7 5 2 8 5 5 54 3 3 2 8 4 0 5 6 9 3 8 9 7 53 2 3 3 9 7 8 9 5 8 6 52 5 4 5 6 5 7 5 26 3 3 7 5 2 7 8 9 5 8 6 56 5 6 5 8 9 7 54 2 3 5 6 3 2 5 54 3 3 2 8 4
8 9 2 5 9 2 5 2 5
0 1 3 2 8 7 5 4 5 3 8 5 8 5 5
0 2 8 6 54 7 8 50 7 7 5 2 8 50 1 2 3 4 5 2 6 7 5 8 9 9 3 2 6 8 5 7
2 8 6 54 7 8 5 0 1 7 8 6 5 2 6 8 5 7 3 9 2 8 6 54 7 8 52 5 9 3 9 8 5 26 3 3 7 5 2 3 9 9 7 8 9 5 8 6 5 5 54 3 3 2 8 4
Page|81
-
7/25/2019 Soochna 2012 Final
85/140
0 1 2 3 4 5 6 7 89 8 3 3 3 7 3 4 9 9 3 7 8 3 4 39 6 4 7 4 3 3 6 3 8 8 30 1 2 3 4 5 6 7 89 6 3 7 6 9 7 3 3 3 7 7 8 3 4 39 9 9 7 6 7 8 6 3 7 4 3 7 3 9 6 7 6 32 9 3 9 4 7 54 3 6 3 7 8 3 6 7 6 4 0 1 2 3 4 5 6 7 89 6 3 7 6 9 7 3 3 3 7 7 8 3 4 39 9 9 7 6 7 8 6 3 7 4 3 7 3 9
9 3 6 32 9 3 9 4 7 54 3 6 3 7 8 3 6 7 6 4
0 1 2 3 4 5 6 7 89 6 7 4 3 3 3 3 74 3 7 3 6 7 39 2 9 3 9 9 6 3 7 8 3 9 4 3 7 3
6 7 39 9 3 6 3 2 9 3 9 1 7 5 4 3 6 3 7 8 3 6 7 6 4
0 1 2 3 4 5 6 7 89 6 7 4 3 3 3 3 74 3 7 3 6 7 39 2 9 3 9 9 6 3 7 8 3 9 4 3 7 3 6 7 39 6 7 6 32 9 3 9 1 7 5 4 3 6 3 7 8 3 6 7 6 4 1 6 6 4 6 3 7 6 9 7 9 6 4 9
9
Page|82
-
7/25/2019 Soochna 2012 Final
86/140
0 1 2 3 1 4 5 6 7 3 8 2 9 1 9 8 3 6 2 1 7 4
2 3 6 2 4 8 2 1 8 9 1
9 4 8 2 9 8 7 1 7 6 5 1
1 2 3 1 3 1 1 2 8 2 1 8 9 1 9 4 8 2
9 8 7 1 7 6 5 1 8 2 5 1 79 1 2 3 1 4 8 2 1
3 4 2 3 6 2 7 6 5 1
6 7 3 8 2 9 1 1 3 1 1 2 6 2 7 6 5 1 8 9 1 9 8 3 6 2 8 5 4 9 8 2 5 8 9 1 2 3 6 2 8 2 1 4 9 8 3 6 9 2 1 7 7 9 8 3 6 2 8 5 4 8 4 8 1 6 7 1 3 1 1 2 8 9 1 8 2 1 1 2 6 2 9 8 3 6 2 8 5 4 6 2 7 6 5 1
8 9 1 6 3 6 2 3 3 8
6 7 3 8 2 9 1 4 3 1 4 8 9 1 9 4 8 2
9 8 7 1 7 6 5 1 8 2 13 9 1 2 3 1 4
2 3 6 2 1 7
8 3 2 1 7 7 9 4 8 2 9 8 7 1 7 6 5 1 8 2 1
8 9 1 6 3 6 2 3 3 8
8 3 2 1 7 7 3 4 8 2 1 8 9 1 6 3 6 2 3 3 8
2 1 3 4 8 2 1 8 4 1 2 1 7 7 1 3 1 1 2 0 4 8 2 9 8 7 1 7 6 5 1 8 2 1 8 9 1 8 2 5 3 4 7 6 5 1 8 2 1 8 9 1 6 3 6 2 3 3 8 6 1 2 7 6 2 1 3 1 1 2 8 2 1 8 9 1 3 4 2 3 6 2 7 6 5 1 8 2 5 9 1 2 3 1 4 1 4 7 6 5 1 1 7 9 4 8 2 9 8 7 1 7 6 5 1
8 2 1
6 1 2 7 6 2 1 3 1 1 2 9 1 2 3 1 4 6 2 1
9 1 2 3 1 4 1 7 3 4 7 6 5 1 8 2 18 2 5
8 2 1 8 9 1 8 3 1 49 1 47 6 5 1
6 1 2 7 6 2 1 3 1 1 2 9 1 2 3 1 4 6 2 1
9 1 2 3 1 4 1 7 3 4 7 6 5 1 8 2 18 2 5
9 1 2 3 1 4 6 2 1 1 7 0 4 8 2 9 8 7 1
7 6 5 1 8 2 1 4 6 1 4 0 4 8 2 9 8 7 1 7 6 5 1 8 2 1 8
8 9 1
4 8 9 14 2 1 7 7 8 8 9 6 2 6 2 8 9 1 4 7 8
6 1 2 7 6 2 1 3 1 1 2 8 2 1 8 9 1
9 4 8 2 9 8 7 1 7 6 5 1 3 6 2 7 6 5 1 8 9 1 9
2 3 6 2 8 2 1
6 1 2 7 6 2 1 3 1 1 2 8 2 1 8 9 1 9 4 8 2 9 8 7 1 7 6 5 1 8 2 5 9 1 2 3 1 4 3 6 2 1 7 6 7 3 8 2 9 1 1 3 1 1 2 9 1 2 3 1 4 2 3 6 2 1 7 9 8 3 2 1 7 7 2 3 6 2 8 2 1 8 9 1 4
9 6 3 6 2
0 1 2 3 1 4 5 6 7 3 8 2 9 1 8 5 4
2 3 6 2 1 7
Page|83
-
7/25/2019 Soochna 2012 Final
87/140
0
1 2 3 4 2 5 6 7 8 4 9 3 2 2 4 2 2 3 4
9 4 7 3 2 8 5 3 4 7 3 0
1 2 3 4 2 5 6 7 8 4 9 3 2 9 4 7 3 2 8 5
3 4 7 3 5 9 3 2 9 2
5 9 3 9 8 2 8 7 6 2
2 3 4 2 4 2 2 3 9 3 2 9 2 5 9 3 9 8 2 8 7 6 2 9 3 6 2 8 2 3 4 2 5 9 3 2 0 4 5 3 4 7 3 8 7 6 2 0 7 8 4 9 3 2 2 4 2 2 3 7 3 8 7 6 2 9 2 9 4 7 3 9 6 5 9 3 6 9 2 3 4 7 3 9 3 2 5 0
9 4 7 3 2 8 8 9 4 7 3 9 6 5
9 5 9 2 7 8 2 4 2 2 3 9 2 9 3 2
2 3 7 3 9 4 7 3 9 6 5 7 3 8 7 6 2
9 2 7 4 7 3 4 4 9
7 8 4 9 3 2 5 4 2 5 9 2 5 9 3
9 8 2 8 7 6 2 9 3 24 2 3 4 2 5 3 4 7 3
2 8 0
9 4 3 2 8 8 5 9 3 9 8 2 8 7 6 2 9 3 2 9 2 7 4 7 3 4 4 9 9 4 3 2 8 8 4 5 9 3 2 9 2 7 4 7 3 4 4 9 3 2 4 5 9 3 2 0 9 5 2 3 2 8 8 2 4 2 2 3 1 5 9 3 9 8 2 8 7 6 2
9 3 2 9 2 9 3 6 4 5 8 7 6 2 9 3 2 9 2 7 4 7 3 4 4 9
7 2 3 8 7 3 2 4 2 2 3 9 3 2 9 2
4 5 3 4 7 3 8 7 6 2 9 3 6 2 3 4 2 5 0
7 3 8 7 6 2 2 5 9 3 9 8 2 8 7 6 2 9 3 2
7 2 3 8 7 3 2 4 2 2 3 2 3 4 2 5 7 3 2
0
2 8 4 5 8 7 6 2 9 3 29 3 6 2 3 4 2 5
0 0 0
7 3 2 2 8 1 5 9 3 9 8 2 8 7 6 2 9 3 2
7 8 4 9 3 2 2 4 2 2 3 2 3 4 2 5 7 3 2 2 8 4 5 9 3 24 9 3 2 9 2 0 5 7 2 5 1 5 9 3 9 8 2 8 7 6 2 9 3 2 0 0 9 9 2 5 9 25 3 2 8 8 9 9 7 3 7 3 9 2 5 8 9
Page|84
-
7/25/2019 Soochna 2012 Final
88/140
00 1 2 3 45 6
7 8 9
3 3
3
7 9 9
7
3 4
6 3
7
9 7 7 7 7 7 7 7 7 7 7 7 7 7 7 9 9 7 9 7 7 7 7
0 1 1 2 1
6 5 5 6 0 0
6 0 0 4 5 0
1 1 0 1 1
5 6 5 6 5 6 0 5 0
6 6 5 2
5 0 0 5
6 4 5 5 6 6 5
5 5 5 0 5 5 5 2 6 5 0 1 6 1 4 0 1 1 5 5 6 3 3 25 0 0 0 0 6 5 6 5
0 0 5 6 0
6 5 6 4 4 5 0 2 4 6 2 6 2 0 2 0 6 2 2 4
9
7 7 7 9 7
Page|85
-
7/25/2019 Soochna 2012 Final
89/140
Page|86
-
7/25/2019 Soochna 2012 Final
90/140
Page|87
-
7/25/2019 Soochna 2012 Final
91/140
Page|88
-
7/25/2019 Soochna 2012 Final
92/140
Page|89
-
7/25/2019 Soochna 2012 Final
93/140
Page|90
-
7/25/2019 Soochna 2012 Final
94/140
Page|91
-
7/25/2019 Soochna 2012 Final
95/140
Page|92
-
7/25/2019 Soochna 2012 Final
96/140
Page|93
-
7/25/2019 Soochna 2012 Final
97/140
Page|94
-
7/25/2019 Soochna 2012 Final
98/140
Page|95
-
7/25/2019 Soochna 2012 Final
99/140
Page|96
-
7/25/2019 Soochna 2012 Final
100/140
Page|97
-
7/25/2019 Soochna 2012 Final
101/140
Page | 98
Section C
Compendium of failure
investigations
-
7/25/2019 Soochna 2012 Final
102/140
Page | 99
INDEX
SN LAB No. Subject Page No.
1 C&M/F35Failure analysis of EXHAUST
SCREEN 100 to 102
2 C&M/F07Failure analysis of MAIN BEARING
BOLT 103 to 106
3 C&M/F13Failure analysis of EXHAUST
VALVE(CYLINDER HEAD) 107 to 110
4 C&M/F3334Failure analysis of BEARING
BRACKET (LB) 111 to 114
5 C&M/F39Failure analysis OF COIL SPRING.
115 to 118
6 C&M/F1011Failure analysis of WATER PUMP
SHAFTS 119 to 124
-
7/25/2019 Soochna 2012 Final
103/140
Page | 100
SUB: FAILURE-INVESTIGATION OF EXHAUST SCREEN to EMD Part No.
9557143 (OF LOCO No. 12152), RECEIVED FROM DLS/HUBLI.
REF: Letter No.(i) H/M/Dsl/Stores/DLW, Dtd. 12.10.2011 of Sr.DME (D), DSL, Hubli.
(ii) Letter No.dlw.65.m.57G, Dtd. 17.10.2011; OF SSE/Eng./DLW
1. BACK-GROUND:
i. The subject component had got failed in service and was noticed during 3rd Yly. Schedule on
12/9/2011. It was of M/s Ranflex make [as mentioned in the letter under Ref. (i)].
ii. The date of commissioning of the Loco was 04/09/08. Thus, obtained Service life was
about three (03) years.
iii. During investigation at the Shed; it was found that, the Screen (S.No. RF 12-07/2-58) had
got damaged.
iv. The failed item was forwarded to this Lab., for detailed investigation, against the
communication under ref. (ii).
v. Results /Finding of the Examinations & Tests are furnished hereunder.
2. VISUAL EXAMINATION:
i. Regarding source of supply, Pnt. No. 1 (i) above refers to.
ii. About 1 of a concentric portion had got parted away, from its center (not received
here) and about 1/4thof one its quadrant (from two adjoining quadrants) had also got
parted (this fragment was received here).
3. CHEMISTRY (Wt %):
Elements Findings Specified Range / Limit(As per AISI Grade- 410),
C 0.13 0.15 Max . .
Mn 0.52 1.00Max. .Si 0.044 1.00Max .S 0.028 0.030 Max
P 0 .024 0.040 Max
Cr 13.48 11.50 13.50
Ni TRACE Not Specified4. Avg. HARDNESS:
Finding Specified Range (As per AISI 410)/Annealed Condition
25RC/ 255 BHN 137-165 BHN (75-85 RB)
-
7/25/2019 Soochna 2012 Final
104/140
Page | 101
5. METALLOGRAPHY (at X100):
A sample-piece, for Micro-structural studies, was cut-out from a nearby vicinity of one parted
edge. The same revealed: - Tempered Martensite with equiaxed Ferrite Grains & DeltaFerrite.
6. DISCUSSIONS:
i. Chemistry of the sample was O.K. as per the specified grade AISI 410.
ii. Hardness of the sample was very high against as specified for annealed condition.
iii. Screen Matl. was in deviation. The same revealed Matrix of Tempered Martensite with
equiaxed Ferrite Grains &Delta Ferrite in lieu of annealed.Delta ferrite, in Hardened
condition, should be avoided to attain the best mechanical properties. Temp. control
during Austenitisation is also important for preventing Delta Ferrite formation. Such
inhomogenity in the matrix also reduces the overall Toughness.iv.
7. CONCLUSION:
In this Case, failure is attributeable to the deviation noticed in matrix and High Hardness as
well.
Temperedmartensite.
Equiaxed
Ferrite
Grains.
Delta Ferrite
-
7/25/2019 Soochna 2012 Final
105/140
Page | 102
8. REMEDIAL MEASURES:
The Basic matl. should be used in proper H/T condition.
C&M/F-35 DATE: 23.12.2011
Dy.C.CMT
DLWDistribution:
i) CQAM/DLW: - For kind information.
ii) CDE / DLW : - For kind information and necessary action, please.
iii) Dy CDE (Eng) / DLW: - For information and necessary action, along-with an extracopy of this report, for onward disposal to the involved
Shed, please.
Encl. one
Annex.-A
Exhaust Screen (Make- Ranflex)CMT Lab No. C&M F-35
.
1 2
3
Exhaust Screen cracked eccentrically circular
about 1 Dia, along a Radial direction and to
a certain extent along the outer circumference
-
7/25/2019 Soochna 2012 Final
106/140
Page | 103
Sub:- FAILURE - ANALYSIS OF MAIN BEARING BOLTto PART NO.16141593/
40056030 (installed in LOCO NO.12188), received from AWM/Engine.
Ref.: Letter No.SSE/ES/EMD/47, Dtd. 25.4.2011; of AWM/Engine.
1.BACKGROUND:
i. The subject component was found broken at BGKT Shed.ii. No other detail/Prima facie report was available with the referred letter.
iii. The component was forwarded to this Lab., for detailed investigation, with the letter
under reference.
iv. Findings /Results of the carried-out Examinations &Tests are furnished hereunder.
2.VISUAL EXAMINATION:
i. Identification mark found on the Head of the Bolt was POOJA FORGE.
ii. The Bolt had got broken from the first Thread into two Fragments.
iii. A Longitudinal-Crack (Typically of a Quenching-Crack type and of about 10 mm in
depth), throughout the length (i.e. covering threads, body and head) was noticed on the
Bolt.
iv. Fracture faces of both the Fragments revealed Characteristic Brittle-fracture, with
clearly defined Beach marked also (Typically Characteristic to Fatigue). The extent of
Fatigue-Crack was about 60 % (originating from root of the Crack). Rest of the
Fracture-face was Crystalline (i.e. last Instantaneous Rupture).
v. Relevant Photo-prints (Nos. 1 to 7), in support of the above said flaws and
appearances, are depicted in Annex. A.
3. CHEMISTRY ( Wt%):
ELEMENTS FINDINGS SPECIFIED Range/Limit, as per
EMS-82/ GM300-M
C 0.45 0.28 - 0.55
P 0.009 0.040Max.S 0.010 0.045Max
Mn 0.91 Obviously Present from Fe-Si & Fe-Mn, used for
Si 0.25 Killing the melt and to increase Hardenibility.Cr 0.99 Should be present (though Limits / Ranges are
Mo 0.18 not specified).
Ni 0.05 Considered as Tramp element.Cu 0.11 - Do - and to increase Corrosion Resistance.
Al 0.016 As remnant after Killing the Steel.
-
7/25/2019 Soochna 2012 Final
107/140
Page | 104
4. Avg. HARDNESS (Rc):-
FINDINGS SPECIFIED Range/Limit, as per
EMS-82/GM300-M
34 33 39
5. METALLOGRAPHY :-
(a)Macro Examination (at X20):
Sample revealed(i) Longitudinal Quenching-Crack, extending across Cross-section and
(ii) Rolled Threads (ref. Fig No. 1 / Annex. B)
(b) Micro-Examination (at X 100 & X 200):Micro-specimen was cut-out from a nearby vicinity of the fracture. It revealed
(i) No detrimental inclusion, in unetched condition.
(ii) In Etched Condition, Tempered Martensitic Matrix with Quenching Crack was
revealed and(iii) Mode of Threading as Rolled.
Relevant Photomicrographs (Nos. 1 to 4) are printed in Annex. B.
6. DISCUSSIONS :-(i) Chemistry, Hardness & mode of Threading of the Bolt were satisfactory. In fact, the Steel
used was a good quality one.(ii) Root of the Longitudinal Quenching-Crack (existing through out the length on the Bolt and
its root, serving as the Fatigue nucleus, led to Stress Concentration - obviously higher at the
Threaded portion; which ultimately gave rise to initiation and propagation of Fatigue- Crack
and when the Endurance Limit was crossed, the final instantaneous rupture had occurred inBrittle mode.
7.CONCLUSION:-Failure of the component is attributed to the point said at 6 (ii), above.
8. REMEDIAL MEASURES:-
H/T cycle must be wisely worked-out and monitored as well, to ensure freedom from such
Quenching-Cracks.
Encl: Annex. A & B
DYCCMT
No. C&M/F-07 DATE: 07.06.2011
Distribution:-
(i)CQAM/DLW .
(ii)CDE/DLW For kind information
(iii)Dy CME (Eng)/ DLW
(iv)Dy.CDE(Eng.)/DLW: - With an additional copy, for onward disposal to the Shed.
Encl.-One
-
7/25/2019 Soochna 2012 Final
108/140
Page | 105
Annexure-A
(1) (2)
(3) (4)
(5)
(6) (7)Fracture-face (at thread end, opposite to Head) Fracture-face (of the body, Counter part,
against Fig.6)
Identification mark
Longitudinal Quenching-Crack,throughout the length of body, & Head