sony dsc h20_sm[1]

7/28/2019 SONY DSC h20_sm[1]

1/58

Revision HistoryRevision History

Sony EMCS Co.DSC-H20_L2

SERVICE MANUAL LEVEL2

Link

DISASSEMBLY

SERVICE NOTE

SPECIFICATIONS

SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM

BLOCK DIAGRAMS

REPAIR PARTS LIST

PRINTED WIRING BOARDS

Link

Internal memoryON BOARD

Internal memoryON BOARD

2009D0500-1 2009.4

Published by Kohda TEC9-852-683-32

The components identified bymark0 or dotted line withmark0 are critical for safety.Replace only with part num-ber specified.

Les composants identifis par unemarque 0 sont critiques pour lascurit.Ne les remplacer que par une piceportant le numro spcifi.

DIGITAL STILL CAMERA

Precautions on Replacing the SY-224 Board

Ver. 1.1 2009.04 US ModelCanadian ModelAEP Model

UK ModelE Model

Australian ModelHong Kong Model

Chinese ModelKorea Model

Argentine ModelBrazilian ModelTourist Model

DSC-H20

Revised-1

Replacement of the previously issuedSERVICE MANUAL 9-852-683-31with this manual.

7/28/2019 SONY DSC h20_sm[1]

2/58 2

DSC-H20_L2

SPECIFICATIONS

Camera

[System]

Image device: 7.79 mm (1/2.3 type) color CCD,Primary color filter

Total pixel number of camera:Approx. 12.4 Megapixels

Effective pixel number of camera:Approx. 10.1 Megapixels

Lens: Carl Zeiss Vario-Tessar 10 zoom lensf = 6.3 mm 63.0 mm (38 mm 380 mm(35 mm film equivalent))F3.5 (W) F4.4 (T)While shooting movies (16:9): 39 mm 390 mm

While shooting movies (4:3): 47 mm 470 mm

Exposure control: Automatic exposure, Manualexposure, Scene Selection (10 modes)

White Balance: Automatic, Daylight, Cloudy,Fluorescent 1,2,3, Incandescent, Flash, OnePush

Recording interval for Burst mode: 0.57 seconds

File format:Still images: JPEG (DCF Ver. 2.0, Exif Ver.2.21, MPF Baseline) compliant, DPOFcompatibleMovies: MPEG4 Visual

Recording media: Internal Memory(approx. 11 MB), Memory Stick Duo media

Flash: Flash range (ISO sensitivity(Recommended Exposure Index) set to Auto):

Approx. 0.2 m to 7.0 m (7 7/8 inches to22 feet 11 5/8 inches) (W)/approx. 0.9 m to 5.5 m (2 feet 11 1/2 inches to18 feet 5/8 inches) (T)

[Input and Output connectors]

Multi use terminal Type2b (AV -out(SD/HDComponent)/USB/DC-in):Video outputAudio output (Stereo)USB communication

USB communication: Hi-Speed USB (USB 2.0compliant)

[LCD screen]

LCD panel:7.5 cm (3.0 type) TFT drive

Total number of dots: 230 400 (960 240) dots

[Power, general]

Power: Rechargeable battery packNP-BG1, 3.6 VNP-FG1 (sold separately), 3.6 VAC-LS5K AC Adaptor (sold separately),4.2 V

Power consumption (during shooting): 1.1 W

Operating temperature: 0C to 40C (32 F to104F)

Storage temperature: 20C to +60C (4F to+140F)

Dimensions:107.3 68.7 47.1 mm (4 1/4 2 3/4 1 7/8 inches) (W/H/D, excluding protrusions)

Mass (including NP-BG1 battery pack andMemory Stick Duo media): Approx. 279 g(9.8 oz)

Microphone: Monaural

Speaker: MonauralExif Print: Compatible

PRINT Image Matching III: Compatible

PictBridge: Compatible

BC-CSGD/BC-CSGE batterycharger

Power requirements: AC 100 V to 240 V,50/60 Hz, 2 W

Output voltage: DC 4.2 V, 0.25 A

Operating temperature: 0C to 40C (32F to104F)

Storage temperature: 20C to +60C (4F to+140F)

Dimensions: Approx. 83 55 24mm(3 3/8 2 1/4 31/32 inches) (W/H/D)

Mass: Approx. 55 g (1.9 oz)

Rechargeable battery pack

NP-BG1

Used battery: Lithium-ion battery

Maximum voltage: DC 4.2 V

Nominal voltage: DC 3.6 V

Maximum charge current: 1.44 A

Maximum charge voltage: DC4.2 V

Capacity:typical: 3.4 Wh (960 mAh)minimum: 3.3 Wh (910 mAh)

Design and specifications are subject tochange without notice.

7/28/2019 SONY DSC h20_sm[1]

3/58 3

DSC-H20_L2

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK0OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes

and bridges.

2. Check the interboard wiring to ensure that no wires arepinched or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

Keep the temperature of the soldering iron around 270C

during repairing.

Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

Be careful not to apply force on the conductor when soldering

or unsoldering.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

ATTENTION AU COMPOSANT AYANT RAPPORT

LA SCURIT!

LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT

CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY

DONT LES NUMROS SONT DONNS DANS CE MANUEL OU

DANS LES SUPPMENTS PUBLIS PAR SONY.

Unleaded solderBoards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.

Unleaded solder melts at a temperature about 40C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.Dispose of used batteries according to the instructions.

7/28/2019 SONY DSC h20_sm[1]

4/581-1

DSC-H20_L2

1. SERVICE NOTE

1-1. PRECAUTION ON REPLACING THE SY-224 BOARD

Restore DataWhen you replace to the repairing board, get the acquire data from the former needed for the adjustment from.

Start the Adjust Manual in the Adjust Station and perform Restore Data to get the data.

The data getting for this model is as follows.

USB Serial No.

Angular Velocity Sensor Sensitivity Adjustment (Dp/Dy Data)

Wide Limit Adjustment

Note: When you cannot read data from the former replace the same time SY-224 board and lens.

Destination DataWhen you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.

Start the Adjust Manual in the Adjust Station and execute the Destination Data Write.

USB Serial No.The set is shipped with a unique ID (USB Serial No.) written in it.

This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.

Start the Adjust Manual in the Adjust Station and execute the USB Serial No. Input.

Angular Velocity SensorWhen you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE401).

Start the Adjust Manual in the Adjust Station and execute the Angular Velocity Sensor Sensitivity Adjustment, input the data written down.

Note: The sensor sensitivity of SE401 of SY-224 board is written only repair parts.

SY-224 BOARD (SIDE B)

SE401

PPPYYY

PPP : PITCH sensor sensitivity

YYY : YAW sensor sensitivity

7/28/2019 SONY DSC h20_sm[1]

5/581-2

DSC-H20_L2

1-2. PRECAUTION ON REPLACING THE LENS

When replacing the lens, write down the PITCH/YAW data and wide limit data given on the lens for service.

Start the Adjust Manual in the Adjust Station and execute the Wide Limit Adjustment and Angular Velocity Sensor Sensitivity Adjustment,

input the data written down.

1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

Note 1: When replacing the SY-224 board, erase the data in internal memory of the board before replacement.Note 2: When replacing the SY-224 board, execute formatting and initialize the internal memory after replacement.

Method for Copying the Data in Internal Memory

Copies all images in the internal memory to a Memory Stick Duo media.

1 Insert a Memory Stick Duo media with sufficient free capacity into the

camera.

2 MENUt (Settings)t (Memory Stick Tool)t [Copy]t [OK]

t z on the control button

Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

Images cannot be copied individually.

The original images in the internal memory are retained even after copying. To delete the contents of the

internal memory, remove the Memory Stick Duo media after copying, then format the internal memory

([Format] in [Internal Memory Tool]).

A new folder is created on the Memory Stick Duo media and all the data will be copied to it. You

cannot choose a specific folder and copy images to it.

Notes

Wide Limit Data (2-byte data)

XXYY

XX YY

YAW data

PITCH/YAW Data

PITCH data

P.PP / Y.YY

P.PP/Y.YY

Note: The PITCH/YAW data and wide limitdata of lens are written only repair parts.

7/28/2019 SONY DSC h20_sm[1]

6/581-3

DSC-H20_L2

Method for Formatting the Internal Memory

1-4. HOW TO WRITE DATA TO INTERNAL MEMORY

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.

This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.

To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust

Station.

Data Writing Method1) Start the Adjust Manual from the Adjust Station.

2) Click (Write Enable Tool) button.

3) Click Active Write Enable Mode button.

4) Upon completion of the setting change, the following message will be displayed.

5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).

6) Write the data read out into the PC to the internal memory of the camera.

7) Disconnect the PC from the camera, and turn off the camera.

Note: By turning off the camera, the write enable setting is reset.

Formats the Memory Stick Duo media or the internal memory. A commercially available

Memory Stick Duo media is already formatted, and can be used immediately.

1 MENUt (Settings)t (Memory Stick Tool) or (Internal

Memory Tool)t [Format]t [OK]t z on the control button

Note that formatting permanently erases all data including even protected images.

Note

7/28/2019 SONY DSC h20_sm[1]

7/581-4

DSC-H20_L2

1-5. SELF-DIAGNOSIS FUNCTION

1-5-1. Self-diagnosis FunctionWhen problems occur while the unit is operating, the self-diagnosis

function starts working, and displays on the LCD screen what to

do.

Details of the self-diagnosis functions are provided in the Instructionmanual.

1-5-2. Self-diagnosis DisplayWhen problems occur while the unit is operating, the LCD screen

shows a 4-digit display consisting of an alphabet and numbers, which

blinks at 3.2 Hz. This 5-character display indicates the repaired

by:, block in which the problem occurred, and detailed codeof the problem.

0 03 2C

Repaired by:

Refer to 1-5-3. Self-diagnosis Code Table.Indicates the appropriatestep to be taken.E.g.13 ....Format the Memory Stick Duo.32 ....Turn on power again.

Block Detailed Code

Blinks at 3.2 Hz

C : Corrected by customerE : Corrected by service

engineer

LCD screen

7/28/2019 SONY DSC h20_sm[1]

8/581-5EDSC-H20_L2

1-5-3. Self-diagnosis Code Table

C

C

E

E

E

E

E

E

E

E

E

BlockFunction

1 3

3 2

6 1

6 1

6 2

6 2

6 2

6 2

6 2

9 1

9 2

DetailedCode

0 1

0 1

0 0

1 0

0 2

1 0

1 1

1 2

2 0

0 1

0 0

Symptom/State

The internal memory has experienced a

media error.

The internal memory has experienced a

format error.

Memory Stick Duo is unformatted.

Memory Stick Duo is broken.

Memory Stick Duo type error

The camera cannot read or write data

on the Memory Stick Duo.

Trouble with hardware

Difficult to adjust focus

(Cannot initialize focus)

Zoom operations fault

(Cannot initialize zoom lens.)

Abnormality of IC for steadyshot.

Lens initializing failure.

Lens overheating (PITCH).

Lens overheating (YAW).

Abnormality of thermistor.

Abnormality when flash is being charged.

Non-standard battery is used.

Self-diagnosis Code

Repairedby:

Correction

Turn the power off and on again.

Format the internal memory.

Format the Memory Stick Duo.

Insert a new Memory Stick Duo.

Insert a supported Memory Stick Duo.

Turn the power off and on again, or taking out and inserting the

Memory Stick Duo several times.

Turn the power off and on again.

Retry turn the power on by the power switch. If it does not

recover, check the focus reset sensor of lens block (pin wj of

CN402 on the SY-224 board). If it is OK, check the focus motordrive IC (IC401 on the SY-224 board).

Retry turn the power on by the power switch. Check the zoom

reset sensor of lens block (pin qj of CN402 on the SY-224board), if zooming is performed when the zoom lever is

operated. If it is OK, check the zoom motor drive IC (IC401 on

the SY-224 board).

Check or replacement of the IC for steadyshot (IC401 on the SY-

224 board).

Check or replacement of the IC for steadyshot (IC401 on the SY-

224 board).

Check the HALL element (PITCH) of optical image stabilizer

(pin3,2 of CN401 on the SY-224 board). If it is OK, check

PITCH/YAW angular velocity sensor (SE401 on the SY-224board) peripheral circuits.

Check the HALL element (YAW) of optical image stabilizer (pin

6,7 of CN401 on the SY-224 board). If it is OK, checkPITCH/YAW angular velocity sensor (SE401 on the SY-224

board) peripheral circuits.

Check the OIS temp sensor of optical image stabilizer (pin ql,w; of CN402 on the SY-224 board).

Checking of flash unit or replacement of flash unit. (Note)

Use the compatible battery only.

Note: After repair, be sure to perform 1-6. PROCESS AFTER FIXING FLASH ERROR.

1-6. PROCESS AFTER FIXING FLASH ERROR

When FLASH error (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash

is changed automatically to disabling charge and flash setting.

After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.

Method for Initializing the Flash Error Code

Initializes the setting to the default setting.

Even if you execute this function, the images are retained.

1 MENUt (Settings)t (Main Settings)t [Initialize]t [OK]tz

on the control button

Be sure not to turn off the camera while initializing.

Note

Ver. 1.1 2009.04

The changed portions fromVer. 1.0 are shown in blue.

7/28/2019 SONY DSC h20_sm[1]

9/582-1DSC-H20_L2

2. DISASSEMBLY

NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of bent at the terminal.Do not insert the cable insufficiently nor crookedly.

When remove a connector, dont pull at wire of connector. It is possible that a wire is snapped.

When installing a connector, dont press down at wire of connector.It is possible that a wire is snapped.

Do not apply excessive load to the gilded flexible board.

Cut and remove the part of giltwhich comes off at the point.(Be careful or some

pieces of gilt may be left inside)

DISCHARGING OF THE CHARGING CAPACITOR (C901, C902)

The charging capacitors (C901, C902) are charged up to the

maximum 300 V potential.

There is a danger of electric shock by this high voltage when thecapacitor is handled by hand. The electric shock is caused by

the charged voltage which is kept without discharging when the

main power of the unit is simply turned off. Therefore, the

remaining voltage must be discharged as described below.

Preparing the Short JigTo preparing the short jig, a small clip is attached to each end of

a resistor of 1 k /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to

prevent electrical shock.

1 k/1 W

Wrap insulating tape.

Note: High-voltage cautions

Discharging the CapacitorShort-circuit between the twopoints with the short jig about10 seconds.

Open the front cabinet a littleand discharge.

R:1 k/1 W(Part code: 1-215-869-11)

C901

C902

7/28/2019 SONY DSC h20_sm[1]

10/582-2

DSC-H20_L2

2-1. IDENTIFYING PARTS

2-2-3. CABINET (UPPER) SECTION

FL-192 Flexible Board

ST-215 Board

2-2-4. MAIN BOARD SECTION

Lens Block

SY-224 Board

Battery Holder

2-2-1. FRONT CABINET SECTION

Cabinet (Front)

2-2-2. REAR CABINET SECTION

Cabinet (Upper)

Cabinet (Rear)

- DISASSEMBLY FLOW -

Cabinet (Rear) FP-1072 Flexible Board

SW-548 Board

Lens Block CCD Block Assy (CD-757 Flexible Board)

Battery Holder Block BT-051 Flexible Board

Cabinet (Upper) FL-192 Flexible Board

FP-1073 Flexible Board

ST-215 Board

SY-224 Board

Cabinet (Front)

LCD

Capacitor Holder

7/28/2019 SONY DSC h20_sm[1]

11/582-3DSC-H20_L2

1 Cabinet (Front)

1-1 (#25)

1-5

(#25)

1-4 (#25)

1-6 (Claw)

1-3 (#25)

1-2 (Open)

1-8E(Claw)

1-7 (Claw)

Rear Cabinet Section(See Page 2-4)

Note: High-voltage cautions

Discharging the CapacitorShort-circuit between the two points with the short jig about 10 seconds.

Open the front cabinet a littleand discharge.

R:1 k/1 W(Part code: 1-215-869-11)

C901

C902

2-2. DISASSEMBLY

2-2-1. FRONT CABINET SECTIONFollow the disassembly in the numerical order given.

1 Cabinet (Front) (1-1 to1-8)

HELPHELP

EXPLODED VIEW HARDWARE LIST

7/28/2019 SONY DSC h20_sm[1]

12/582-4DSC-H20_L2

1-1 (#23)

1-2E

2-1

2-6(#23)

2-2(Claw)

2-7(Claw)

2-8 (Claw)

2-9E(Claw)

2-3

2-4

2-5

Main Board Section(See page 2-6)

1Cabinet (Upper)(See Page 2-5)

2Cabinet (Rear)

HELP01

HELP08

2-2-2. REAR CABINET SECTION

Follow the disassembly in the numerical order given.

1 Cabinet (Upper) (1-1 to1-2)2 Cabinet (Rear) (2-1 to2-9)


7/28/2019 SONY DSC h20_sm[1]

13/582-5DSC-H20_L2

2-2-3. CABINET (UPPER) SECTIONFollow the disassembly in the numerical order given.

1 ST-192 Flexible Board (1-1 to1-12)2 ST-215 Board (2-1 to2-3)


1-1(Disconnect)

1-10

1-12E

1-6

1-4 (#23)

1-7 (#23)

1-9 (Claw)

1-2(Claw)

1-3(Claw)

1-8 (Claw)

1-5 (Claw)

1-11 (Boss)

2-1 (#23)

2-2 (Claw)

2-3E

2ST-215 Board

ST-215

1FL-192Flexible

Board

HELP02

HELP07

HELP05

7/28/2019 SONY DSC h20_sm[1]

14/582-6EDSC-H20_L2

2-2-4. MAIN BOARD SECTIONFollow the disassembly in the numerical order given.

1 Lens Block (1-1 to1-3)2 SY-224 Board (2-1 to2-5)3 Battery Holder (3-1 to3-5)


1-1

1-2

1-3E

1Lens Block

2SY-224 Board

2-1(#25)

2-22-4

2-5E

A

A

2-3(Claw)

3-3

3-2

3-5E

3-4(Claw)

3-1 (Claw)

3Battery Holder

HELP03

HELP04

HELP06

7/28/2019 SONY DSC h20_sm[1]

15/58

DSC-H20_L2HELP

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

MS Slot

HELP04:Spacer (G)/Radiation Sheet (S)

Spacer (G)

Radiation Sheet (S)

Main Frame

HELP03: Electrostatic Sheet (SY)/Radiation Sheet (SY)

Radiation Sheet (SY)

Electrostatic Sheet (SY)

HELP02:ST-215 Board

ST-215 Board

Claw

Rotate the dial until stopping.

Put the lever of zoom switchtogether on the center.

HELP01:Protection Sheet (MS)

Protection Sheet (MS)

7/28/2019 SONY DSC h20_sm[1]

16/58

DSC-H20_L2

HELP

HELP05: The Method of Attachment of FL-192 Flexible Board

1 Apply the fold habit to the FL-192 flexible board. 3 Match the FL-192 flexible board to two bossesof the ST base assy and put it.

4 Assemble the flash unit to the ST base assy.

5 Hang the claw in three places, and attach the STcase (upper) assy to the ST base assy.

6 Tighten up a screw.ST Case (Upper) Assy

ST Base Assy

2 Pass the FL-192 flexible board through the spaceof the ST base assy.

3 Fix three holes of plunger solenoid into bosses of

the ST base assy.

Reinforcement Plate

Bosses

Claw

Screw

Claw

Bosses

7/28/2019 SONY DSC h20_sm[1]

17/58

DSC-H20_L2

HELP

0 Shut the pop up.

qa Pass the detection switch part through the rib ofthe ST base assy.

9 Fix the AF part by the three claws.

7 Fix two holes of AF holder into bosses of the

ST base assy.8 Tighten up a screw.

qs Make the detection switch part slide into to theclaw of ST base assy.

qd Fix two bosses of ST base assy.

AF HolderBosses

Screw

AF Part

Detection Switch PartClaw

ClawBosses

7/28/2019 SONY DSC h20_sm[1]

18/58

DSC-H20_L2

HELP

Lens Retainer Cushion

From the lens engaged line,upward within 1mm anddownward within 0mm.

HELP06: Lens Flexible Protection Sheet/Lens Retainer Cushion/Radiation Sheet (CD)

HELP07: FP-1073 Flexible Board

HELP08:Microphone Harness

Microphone

FP-1073 Flexible Board

ST-215 Board

1 Have the main body of the microphone, and make three rotations.

2 Twist the microphone harness.

3 Install the microphone in the capacitor holder.

Capacitor Holder.

Radiation Sheet (CD)

Lens Flexible Protection SheetLens flexible cableis soldered.

Rib

Rib

7/28/2019 SONY DSC h20_sm[1]

19/58

DSC-H20_L2

LinkLink

3. BLOCK DIAGRAMS

OVERALL BLOCK DIAGRAM (2/2)

OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2)

POWER BLOCK DIAGRAM (2/2)

7/28/2019 SONY DSC h20_sm[1]

20/58

7/28/2019 SONY DSC h20_sm[1]

21/58

7/28/2019 SONY DSC h20_sm[1]

22/58

7/28/2019 SONY DSC h20_sm[1]

23/58

7/28/2019 SONY DSC h20_sm[1]

24/58

4-1

DSC-H20_L2

4-1. FRAME SCHEMATIC DIAGRAM

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

CN401

CN402

CN301

CN704

CN705

CN701

2

22

1

23

124

45 1

46 2

21

44

45

12

26

27

21

44 4

5

21

28 2

9

LEVEL3

SY-224 BOARD

(SIDE A)

SW-548BOARD(SIDE A)

SW-548BOARD (SIDE B)

ST-215 BOA(SIDE A)

ST-215 BOARD(SIDE B)

BT-051FLEXIBLEBOARD

CD-757FLEXIBLEBOARD

FP-1073FLEXIBLEBOARD

FP-1072 FLEXIBLEBOARD

FL-192 FLEXIBLE BOARD

LEVEL3

SY-224 BOARD (SIDE B)

112

CN703

1 10

1211

CN001

12

26

27

CN002

CN003

24

1

2

1

28

29

1 12

1

27

27

1

24 1

29 1

45

1

IC201(Not supplied)

24

1

CN702

(MULTI CONNECTOR)

C902

CHARGING

CAPACITOR

S

BT901

BATTERYTERMINAL

LCD901LCD MODULE

BACKLIGHT

3.0 INCHCOLOR

LCD UNIT

C901

CHARGING

CAPACITOR

FLASH UNIT

BT900

LITHIUM BATTERY

SP901

(SPEAKER)

Red

Black

MIC901

(MICROPHONE)

Black

White

CN002

MEMORY STICKCONNECTOR

7/28/2019 SONY DSC h20_sm[1]

25/58

4-2. SCHEMATIC DIAGRAMS

DSC-H20_L2

ST-215 BOARD (1/2) (FLASH DRIVE)

SW-548 BOARD (CONTROL SWITCH)CD-757 FLEXIBLE BOARD (CCD IMAGER)

FL-192 FLEXIBLE BOARD (FLASH UNIT)

ST-215 BOARD (2/2) (CONTROL SWITCH)

BT-051 FLEXIBLE BOARD (BATTERY IN)

FP-1073 FLEXIBLE BOARD(SY-ST CONNECTION)

FP-1072 FLEXIBLE BOARD(SY-SW CONNECTION)

LinkLink

COMMON NOTE FOR SCHEMATIC DIAGRAMS

7/28/2019 SONY DSC h20_sm[1]

26/584-2DSC-H20_L2

4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS

1. Connection

2. Adjust the distance so that the output waveform ofFig. a and the Fig. b can be obtain.

When indicating parts by reference number, pleaseinclude the board name.

(For schematic diagrams) All capacitors are in F unless otherwise noted. pF :

F. 50 V or less are not indicated except for electrolyticsand tantalums.

Chip resistors are 1/10 W unless otherwise noted.k=1000, M=1000 k.

Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.

Some chip part will be indicated as follows.Example C541 L452

22U 10UHTA A 2520

Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.

Parts with differ according to the model/destination.Refer to the mount table for each function.

All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.

Signal nameXEDIT EDIT PB/XREC PB/REC

2: non flammable resistor5: fusible resistorC: panel designation

A: B+ LineB: B Line J : IN/OUT direction of (+,) B LINE.C: adjustment for repair.(Measuring conditions voltage and waveform) Voltages and waveforms are measured between the

measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 M input impedance is used)

Voltage values change depending upon inputimpedance of VOM used.)

Kinds of capacitorCase size

External dimensions (mm)

Yellow

A AB BA=B

Fig. a (Video output terminal output waveform)

H

Cyan

Green

White

Magenta

Red

Blue

Fig.b (Picture on monitor TV)

CRT picture frame

Electronic beamscanning frame

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)

Pattern box

Pattern box PTB-450

J-6082-200-A

or

Small pattern box

PTB-1450

J-6082-557-A

Color bar chart

For PTB-450:

J-6020-250-A

For PTB-1450:

J-6082-559-A

Pattern boxFront of the lens

L = 26 cm (PTB-450)L = 11 cm (PTB-1450)

L Camera

Precautions for Replacement of Imager

If the imager has been replaced, carry out all the adjustmentsfor the camera section.

As the imager may be damaged by static electricity from

its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with

dusts nor exposed to strong light.

The components identified by mark 0 or dotted line withmark 0 are critical for safety.Replace only with part number specified.

Les composants identifis par une marque 0 sontcritiques pour la scurit.Ne les remplacer que par une pice portant le numrospcifie.

4-2. SCHEMATIC DIAGRAMS

7/28/2019 SONY DSC h20_sm[1]

27/58

4-3DSC-H20_L2

Note: Voltages of IC001 and IC002 can not be measured,because they are mounted by the side of the lens.

Note: IC001 (CCD imnot supplied, b

D

C

6

B

A

53 4

F

2

E

1

V5C

V 5 B

VST1

VST2

V6S2

V6S1

V5B

V5C

V5A

V6S1

V4

V6S2

V3C

VST2

V3B

VST1

V3A

V2

V1B

V1A

LV

VOG

SUB

VHLD2

VHLD1

CAM_13V

CAM_-7.5V

C0060.1u16V

C0030.22u16V

R003 270kIC002

CXA3741AUR-T9

1

SFCNT

2

IDRV0

3

IDRV1

4

GND

5

6

7

8

9101112

13 NC

14 OUT

15 GND

16 DRVCNT

17 GND

C0090.01u25V

C0070.01u25V

LND005

LND017

LND040

LND030

LND020

LND029

LND023

LND027

LND035

LND010

LND012

LND001

LND024

LND022

LND011

LND009

LND015

LND018

LND016

LND034

LND033

LND026

LND019

LND014

LND028

LND021

LND038

LND031

LND039

LND042

LND006

LND037

LND025

LND004

LND043

LND032

LND003

LND013

LND044

LND036

LND007

LND002

LND045

LND008

LND041

1

15 V5C

16 V6S1

17 V6S2

18 VST2

24 NC

25 AGND

2

22 NC

23 RG

19 VST1

20 VOUT

21 VDD

R007

330k

R009

220k

R008 120kH2

SUB

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

V1A

VL(CAM_-7.5V)

V3A

REG_GND

REG_GND

REG_GND

REG_GND

V6S1

V5C

VST2

CAM_13V

H1

45pin

VOG

VHLD2

V1B

V4

LH1

H3

V3B

V5B

1pin

RG

V2

VHLD1

V5A

SUB_CONT

REG_GND

V6S2

V3C

REG_GND

LV

VST1

REG_GND

REG_GND

CCDOUT

POWER_SAVE

REG_GND

BUFFER

XX MARK:N

CCD IM

CD-7

(1/9)SY-224

of Level 3

CN301

Page 4-4

C0080.01u

25V

C0010.01u25V

VCC

ISF0

ISF1

NC

GND

IN

GND

NC

H1

H2

H3

LH1

RG

CCD_OUT

P/S

SUB_CONT

05

7/28/2019 SONY DSC h20_sm[1]

28/58

DSC-H20_L2

Schematic diagram of the SY-224 board is not shown.Pages from 4-4 to 4-12 are not shown.

7/28/2019 SONY DSC h20_sm[1]

29/58

4-13DSC-H20_L2

0

3.9

0

3.2

0

3.2

0 3.2

0

S

D

C

6

B

A

53 4

F

2

E

1

D003MA2YF8000LS0

LND040 C-

C004XX

C00322u

6.3V LND037 C-

LND039 C+

R005100

LND041

-

R002XX

LND038

+

LND036 C+

IC001BD4215NUV-E2

1

PGND

2

IGBT

_OUT

3

FLASH

_ON

4

XFULL

5

IPEAK

678910

11HGND

D_3.2V

1

85

2 3 4

6 7

CN003 29P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

L0022.2uH

T001

3

4

5

1

2

C90279u

315V

C90193u

315V

DischargeDischarge

FLASH CONTROL,CHARGE CONTROL

KEY_AD2

XSTRB_POPUP

XAF_LED

AF_5V

STRB_PLUNGER

XPWR_ON

ST_UNREG

XSHUT_SW

D_3.2V

XPWR_LED

STRB_ON

STRB_CHG_CONT

STRB_CHG

XSTRB_FULL

XAE_LOCK

MODE_DIAL1

REG_RND

REG_RND

ST_UNREG

REG_RND

REG_RND

REG_RND

REG_RND

REG_RND

STRB_PLUNGER

ST_UNREG

ST_UNREG

ST_UNREG

REG_RND

XSHUT_SW

XAE_LOCK

MODE_DIAL1

REG_GND

XPWR_LED

XPWR_ON

KEY_AD2

D002XX

C0024.7u6.3V

IGBT

_EN

CHARGE

_ON

VCC

VOUT

SW

CAPACITORCHARGING

CAPACITORCHARGING

Q002TIG052TS-TL-EFLASH DRIVE

05

C00610p

50V

Page 4-16

LND025-LND053

FP-1073

of Level 2

FLEXIBLE

Refer to page 4-2 for mark0.

7/28/2019 SONY DSC h20_sm[1]

30/58

4-14DSC-H20_L2

Note: S101 (mode dial) is not supplied,but this is included in ST-215 complete board.

A

D

CC

D

B

E

A

B

3 4

F

2

F

E

1

LND109

RB1012200

12345678

RB102

2200

1

2

3

4

5

6

7

8

D102XX

D103XX

S104

3

COM1

8

COM2

1

A

2

B1

9

B2

10

GND

4 j

5 i

6 f

7 h

1

3

2

4

3

4

5

6

1 7

8

9

10

11

12

13

14

2

1

3

2

4

R101 270

D104

XX

1

23

VDR101

(2nd)

Static_GND

(1st)

(SHUTTER)

MOVIE

SCN

EASY

AUTO

P_AUTO

MANUAL

MOVIE

CONTROL SWITCHXX MARK:NO MOUNT

ST-215 BOARD (2/2)

REG_GND

XSHUT_SW

XAE_LOCK

D_3.2V

XPWR_LED

KEY_AD2

XPWR_ON

MODE_DIAL1

S101(MODE DIAL)

R10210k

S102

ON/OFF

TELE SLOW

TELE FAST

WIDE FAST

WIDE SLOW

W

(ZOOM)

T

S103(SMILE SHUTTER)

D101SML-412MWT86

(POWER)

05

15

16

17

18

MAZP068H0AS0


D

C

B

A

F

2

E

1

LND003

LND020

LND019

LND018

LND017

LND016

LND015

LND014

LND013

LND012

LND011

LND010

LND009

LND008

LND007

LND006

LND005

LND004

LND022

LND023

LND002

LND021

C000.047

250

LND001

LND024

1pin

24pin

1SS

C0021u 10V

XX MAR

FLAS

FL-

R001

1M

05

REG_GND

REG_GND

AF_5V

REG_GND

N C

XAF_LED

STRB_PLUNGER

N C

N C

N C

XE_L

XE_H

XE_H

XE_H

N C

REG_GND

N C

XE_L

XE_L

XE_L

XE_H

STRB_PLUNGER

REG_GND

XSTRB_POPUP

1

2

3

4

8

12

13

6

16

7

17

14

11

10

9

5

18

19

20

21

22

23

24

15

(1/2)ST-215

of Level 2

CN002

Page 4-13

7/28/2019 SONY DSC h20_sm[1]

31/58

4-15DSC-H20_L2

D

C

6

B

A

53 4

F

2

E

1

1

3

2

4

1

3

2

4

S006 1

3

2

4

RB001

2200

1

2

3

4

5

6

7

8

1

3

2

4

1

3

2

4

S002 1

3

2

4

1

3

2

4

R006 68

R010 0

LND001

STATIC_GND

R004 68

R0020

R005 68

R007 1k

R003 56

R008 68

D002XX

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

R0012200

LND002

LND003

CN002 10P

1 VSS

2 MS_BS

3 DATA1

4 SDIO/DATA0

5 DATA2

6 INT

7 DATA3

8 S CLK

9 VCC

10 VSS

11

12

D003XX

3 2

1

LND004

SPEAKER_GND

S007 1

3

2

4

VDR001

SP901(SPEAKER)

DUOSTICK

MEMORY

(MACRO)

CN001 27P

REG_GND

SP-

SP+

SPEAKER_GND

XACCESS_LED

D_3.2V

REG_GND

MS_VCC

REG_GND

MS_CLK

REG_GND

MS_D3

REG_GND

XMS_IN

REG_GND

MS_D2

REG_GND

MS_D0

REG_GND

MS_D1

REG_GND

MS_BS

REG_GND

XDIRECT_PB

KEY_AD1

KEY_AD0

REG_GND

D001SML-D12V8WT86SN

(MS ACCESS)

R009

FB001

FB002

FB003

FB004

0

0

0

0

0

C00122u6.3V

C002

0.22u

MENU

S003

(SELF-TIMER)

S005

(FLASH)

S004

(SET)

S001

(DISP)

S008

(DELETE)

R011470

05

Page 4-16

LND054-LND028

FP-1072

of Level 2

FLEXIBLE

7/28/2019 SONY DSC h20_sm[1]

32/58

4-16DSC-H20_L2

Note: BT900 and BT901 are not includedin BT-051 flexible board.

A

3

C

2

B

1

B

A

C

4

LND011

LND007

LND001

LND015

BATT_UNREG

LND017

BATT_GND

LND016

BATT_SIG

LND010

LND009

LND008

LND003

LND004

LND005

LND006

LND002

LND012

05

LND014

VL_3V

LND013

REG_GND(LITHIUM BATTERY)

BT900

REG_GND

REG_GND

REG_GND

REG_GND

BATT_SIG

BATT_UNREG

N.C

BATT_UNREG

BATT_UNREG

BATT_UNREG

VL_3V

REG_GND

BATTERY IN

1pin

12pin

S

BT-051 FLEXIBLE BOARD

(9/9)SY-224

of Level 3

CN703

Page 4-12

BT901

TERMINALBATTERY

(PRINTED WIRING BOARD is omitted.)

A

3

C

2

B

1

B

A

C

4

LND003 KEY_AD1

LND004 XDIRECT_PB

LND005 REG_GND

LND006 MS_BS

LND007 REG_GND

LND008 MS_D1

LND009 REG_GND

LND010 MS_D0

LND011 REG_GND

LND019 REG_GND

LND016 MS_D3

LND012 MS_D2

LND018 MS_CLK

LND013 REG_GND

LND014 XMS_IN

LND017 REG_GND

LND020 MS_VCC

LND015 REG_GND

LND037MS_D0

LND034REG_GND

LND046REG_GND

LND041XMS_IN

LND045MS_CLK

LND047MS_VCC

LND030KEY_AD1

LND036REG_GND

LND031XDIRECT_PB

LND032REG_GND

LND035MS_D1

LND042REG_GND

LND043MS_D3

LND040REG_GND

LND038REG_GND

LND039MS_D2

LND044REG_GND

LND033MS_BS

LND048REG_GNDLND021 REG_GND

LND029KEY_AD0LND002 KEY_AD0

LND027

05

REG_GND LND054REG_GND

LND022 D_3.1V

LND053SP-

LND025 SP+ LND052SP+

LND049D_3.1V

LND024 REG_GND

LND026 SP-

LND051REG_GND

LND050XACCESS_LEDLND023 XACCESS_LED

LND001 REG_GND LND028REG_GND

1pin

27pin

27pin

1pin

SY-SW CONNECTION

FP-1072 FLEXIBLE BOARD

(9/9)SY-224

of Level 3

CN704

Page 4-12

SW-548

of Level 2

CN001

Page 4-15

(PRINTED WIRING BOAR

LND001

LND006

LND013

LND005

LND012

LND011

LND015

LND009

LND002

LND017

LND008

LND016

LND003

LND004

LND020

LND018

LND023

LND007

LND019

LND024

LND022

LND014

LND021

LND010

24pin

1pin

SY-ST CONNEC

FP-1073 F

05

CN701

Page 4-12of Level 3

SY-224(9/9)

AF_5V

ST_UNREG

STRB_CHG

ST_UNREG

STRB_CHG_CONT

STRB_ON

XSTRB_POPUP

REG_GND

XAF_LED

XPWR_LED

REG_GND

D_3.1V

REG_GND

STRB_PLUNGER

XSHUT_SW

XPWR_ON

KEY_AD2

ST_UNREG

XAE_LOCK

REG_GND

MODE_DIAL1

XSTRB_FULL

REG_GND

REG_GND

D

C

B

A

21


7/28/2019 SONY DSC h20_sm[1]

33/58

4-3. PRINTED WIRING BOARDS

DSC-H20_L2

LinkLink

CD-757 FLEXIBLE BOARD SW-548 BOARD

ST-215 BOARD

FL-192 FLEXIBLE BOARD

BT-051 FLEXIBLE BOARD

COMMON NOTE FOR PRINTED WIRING BOARDS

7/28/2019 SONY DSC h20_sm[1]

34/584-18DSC-H20_L2

4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS

2 1

3

2 1

3

2 1

3

345

21

123

654

EB

C

31

5

2

46

123

654

31

5

2

46

123

54

4 3

1 2

31 2

45

53 4

12

14

23

46

2

5

31

12

43

14

23

: Uses unleaded solder. : Circuit board

: Flexible boardPattern from the side which enables seeing.

: pattern of the rear side(The other layers patterns are not indicated)

Through hole is omitted. There are a few cases that the part printed on diagram

isnt mounted in this model.C: panel designation

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS

4-3. PRINTED WIRING BOARDS

Chip parts.Transistor Diode

7/28/2019 SONY DSC h20_sm[1]

35/58

4-19DSC-H20_L2

CD-757 (2 layers)

: Uses unleaded solder.

CD-757

>P

7/28/2019 SONY DSC h20_sm[1]

36/58

DSC-H20_L2

Printed wiring board of the SY-224 board is not shown.Page 4-20 is not shown.

7/28/2019 SONY DSC h20_sm[1]

37/58

4-21DSC-H20_L2

ST-215 (4 layers), FL-192 (2 layers)

: Uses unleaded solder.

C002

C003

C004

C006

D002

D003

RB101

RB102

IC001

T001

VDR101

R101

R102

S101

S102

S103

S104

D101

D102

D103

D104

L002

R002

LND109

4

1 2

35

5

6 10

1

11

3

4

2

1

3

3 4

7

10

8

1

4 2

1

1

7

2

8

1

7

2

8

LND036LND037

LND038LND039 LND040

LND041

7

2

6

5

15183 414

12

1

13

11

17 169 810

AK

A

K

C901CHARGINGCAPACITOR

C902CHARGINGCAPACITOR

+

+

1-877-942- 11

ST-215 BOARD (SIDE A)

05

(MODE DIAL)

ON/OFF(SHUTTER)

(SMILE SHUTTER)

(POWER)

(ZOOM)

W

T

Note: S101 (mode dial) is not supplied, but this isincluded in ST-215 complete board.

CN002

CN003

Q002

R004

R005

24

1

14

5 8

2

1

28

29

1-877-942- 11

ST-215 BOARD (SIDE B)

05

FL-192

>PI

0BT900 1-756-813-11 LITHIUM RECHARGEABLE BATTERY

A-1716-417-A CCD BLOCK ASSY (SERVICE)

(Not supplied) CD-757 FLEXIBLE BOARD, COMPLETE

*******************************

(IC001 (CCD imager) and CD-757 flexible complete board are not supplied,

but they are included in CCD block assy.)

< CAPACITOR >

C001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V


*

C005 1-114-582-11 CERAMIC CHIP 0.1uF 10% 16V* C006 1-114-582-11 CERAMIC CHIP 0.1uF 10% 16V




* C010 1-114-582-11 CERAMIC CHIP 0.1uF 10% 16V

< IC >

IC001 (Not supplied) IC ICX667HQW-13 (CCD IMAGER) (Note)

(IC001 is supplied including in the CCD block assy.)

* IC002 8-753-294-89 IC CXA3741AUR-T9

< RESISTOR >

R003 1-218-982-11 METAL CHIP 270K 5% 1/16W

R007 1-218-983-11 METAL CHIP 330K 5% 1/16W

R008 1-218-978-11 METAL CHIP 120K 5% 1/16W

R009 1-218-981-91 METAL CHIP 220K 5% 1/16W

A-1711-442-A FL-192 FLEXIBLE BOARD, COMPLETE

*******************************

0 1-480-062-11 FLASH UNIT

< CAPACITOR >


C002 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

< DIODE >

D001 8-719-988-61 DIODE 1SS355TE-17

* D003 6-501-861-01 DIODE CL-360S-TD4-X-TL

(SELF-TIMER, SMILE SHUTTER, AF ILLUMINATOR)

< COIL >

0* L001 1-457-498-21 TRIGGER COIL

< RESISTOR >

0R001 1-216-121-11 METAL CHIP 1M 5% 1/10W

< PLUNGER >

* RY001 1-455-056-11 SOLENOID, PLUNGER

< SWITCH >

S001 1-786-180-11 SWITCH, PUSH (1KEY)

(STROBE POP-UP DETECT)

A-1717-440-A ST-215 BOARD, COMPLETE

**********************

(S101 (mode dial) is not supplied, but this is included in ST-215 complete

board.)

< CAPACITOR >

* C002 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C003 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V

C006 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V0C901 1-116-144-11 ELECT 93uF 315V

0C902 1-116-143-11 ELECT 79uF 315V

< CONNECTOR >

* CN002 1-816-650-51 FFC/FPC CONNECTOR (LIF) 24P

* CN003 1-818-818-81 CONNECTOR, FPC (ZIF) 29P

< DIODE >

0D003 6-501-141-01 DIODE FT02P80TP

D101 6-501-030-01 DIODE SML-412MWT86 (POWER)

D104 6-501-080-01 DIODE MAZP068H0AS0

< IC >

* IC001 6-712-975-01 IC BD4215NUV-E2

< COIL >

* L002 1-481-098-11 INDUCTOR 2.2uH

< TRANSISTOR >

0* Q002 6-552-144-01 TRANSISTOR TIG052TS-TL-E

< RESISTOR >

R004 1-218-989-11 METAL CHIP 1M 5% 1/16W

R005 1-218-941-11 METAL CHIP 100 5% 1/16WR101 1-218-946-11 METAL CHIP 270 5% 1/16W

R102 1-218-965-11 METAL CHIP 10K 5% 1/16W

< COMPOSITION CIRCUIT BLOCK >

RB101 1-234-376-11 RES, NETWORK 2.2K (1005X4)

RB102 1-234-376-11 RES, NETWORK 2.2K (1005X4)

< SWITCH >

S101 (Not supplied) ROTARY SWITCH (MODE DIAL)

(S101 is supplied including in ST-215 complete board.)

* S102 1-786-914-31 SWITCH, TACTILE (ON/OFF)

Note: Be sure to read Precuations for Replacement ofImager on page 4-2 when changing the imager.

BT-051 CD-757 FL-192 ST-215

CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.Dispose of used batteries according to the instructions.

7/28/2019 SONY DSC h20_sm[1]

47/585-8

Ref. No. Part No. Description Ref. No. Part No. Description

DSC-H20_L2

Refer to page 5-1 for mark 0.

* S103 1-786-914-31 SWITCH, TACTILE (SMILE SHUTTER)

* S104 1-798-234-11 TACTILE SWITCH (ZOOM SWITCH)

(SHUTTER, ZOOM)

< TRANSFORMER >

0* T001 1-445-491-21 D.C.-D.C.CONVERTER TRANSFORMER

A-1717-441-A SW-548 BOARD, COMPLETE

***********************

< CAPACITOR >

C001 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V

C002 1-165-887-91 CERAMIC CHIP 0.22uF 10% 6.3V

< CONNECTOR >

* CN001 1-817-829-81 CONNECTOR, FPC (ZIF) 27P

CN002 1-819-611-21 MEMORY STICK DUO CONNECTOR 10P

< DIODE >

D001 6-502-193-01 DIODE SML-D12V8WT86SN (MS ACCESS)

< SHORT >

FB001 1-218-990-81 SHORT CHIP 0 (Note)




< RESISTOR >

R001 1-218-957-11 METAL CHIP 2.2K 5% 1/16W

R002 1-218-990-81 SHORT CHIP 0

R003 1-218-938-11 METAL CHIP 56 5% 1/16W

R004 1-218-939-11 METAL CHIP 68 5% 1/16W

R005 1-218-939-11 METAL CHIP 68 5% 1/16W

R006 1-218-939-11 METAL CHIP 68 5% 1/16W

R007 1-218-953-11 METAL CHIP 1K 5% 1/16W

R008 1-218-939-11 METAL CHIP 68 5% 1/16W

R009 1-218-990-81 SHORT CHIP 0

R010 1-218-990-81 SHORT CHIP 0

R011 1-218-949-11 METAL CHIP 470 5% 1/16W

< COMPOSITION CIRCUIT BLOCK >

RB001 1-234-376-11 RES, NETWORK 2.2K (1005X4)

< SWITCH >

* S001 1-786-914-31 SWITCH, TACTILE (v, DISP)

* S002 1-786-914-31 SWITCH, TACTILE (b, MACRO)

* S003 1-786-914-31 SWITCH, TACTILE (V, SELF-TIMER)

* S004 1-786-914-31 SWITCH, TACTILE (z, SET)

* S005 1-786-914-31 SWITCH, TACTILE (B, FLASH)

* S006 1-786-914-31 SWITCH, TACTILE (N)* S007 1-786-914-31 SWITCH, TACTILE (MENU)

* S008 1-786-914-31 SWITCH, TACTILE (DELETE)

< SPEAKER >

SP901 1-826-403-31 LOUDSPEAKER (1.0CM)

< VARISTOR >

VDR001 1-803-974-21 VARISTOR, CHIP (1608)

Electrical parts list of the SY-224 board is notshown.Pages from 5-9 to 5-12 are not shown.

Note: Short chips are mounted to the loca-tion where FB001 to FB004 are printed.

ST-215 SW-548

7/28/2019 SONY DSC h20_sm[1]

48/585-13EDSC-H20_L2

Conversion (2P) Adaptor0 1-569-008-12

(E (Except Middle East))

Conversion (2P) Adaptor0 1-569-007-12 (JE)

Wrist Strap2-050-981-11

Lens CapX-2348-963-1

Instruction Manual4-133-905-11 (ENGLISH)

(CND, AEP, UK, E, HK, AUS, JE)4-133-905-21 (FRENCH, ITALIAN) (CND, AEP)4-133-905-31 (SPANISH, PORTUGUESE) (AEP, E, AR, JE)4-133-905-41 (GERMAN, DUTCH) (AEP)4-133-905-51 (TRADITIONAL CHINESE,

SIMPLIFIED CHINESE) (HK, JE)4-133-905-61 (RUSSIAN, UKRAINIAN) (AEP)4-133-905-71 (ARABIC, PERSIAN) (E)

4-133-905-81 (KOREAN) (KR, JE)4-133-905-91 (POLISH, CZECH) (AEP)4-133-906-11 (HUNGARIAN, SLOVAK) (AEP)4-133-906-21 (SWEDISH, FINNISH) (AEP)4-133-906-31 (NORWEGIAN, DANISH) (AEP)4-133-906-41 (CROATIAN, ROMANIAN) (AEP)4-133-906-51 (TURKISH, GREEK) (AEP)4-133-906-61 (ENGLISH, SPANISH) (US)4-133-906-71 (SIMPLIFIED CHINESE) (CH)4-133-906-81 (MALAY, INDONESIAN) (E)4-133-906-91 (ENGLISH, THAI) (E)4-145-250-11 (TRADITIONAL CHINESE,

SIMPLIFIED CHINESE) (E)

Power Cord (Mains Lead)(EXCEPT US, CND, BR)0 1-783-952-71 (AR)0 1-832-121-41 (CH)0 1-832-169-41 (UK, HK)0 1-833-892-41 (KR)0 1-834-482-31 (AEP, E)0 1-835-983-11 (AUS)0 1-836-251-11 (JE)

CD-ROM(Cyber-shot application software/

Cyber-shot Handbook/Cyber-shot Step-up Guide)

4-133-900-02

Cyber-shot Handbook (PDF)

The CD-ROM supplied contains all of language version ofthe Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing. The printed matter is not supplied. If required, please

order it with the part number below. (Only for destination Japanese model)

4-133-901-01 (JAPANESE)* 4-133-901-11 (ENGLISH)* 4-133-901-21 (FRENCH)* 4-133-901-31 (ITALIAN)* 4-133-901-41 (SPANISH)* 4-133-901-51 (PORTUGUESE)* 4-133-901-61 (GERMAN)* 4-133-901-71 (DUTCH)* 4-133-901-81 (TRADITIONAL CHINESE)* 4-133-901-91 (SIMPLIFIED CHINESE)* 4-133-902-11 (RUSSIAN)* 4-133-902-21 (ARABIC)*

4-133-902-31 (PERSIAN)* 4-133-902-41 (KOREAN)* 4-133-902-51 (POLISH)

* 4-133-902-61 (CZECH)* 4-133-902-71 (HUNGARIAN)* 4-133-902-81 (SLOVAK)* 4-133-902-91 (SWEDISH)* 4-133-903-11 (FINNISH)* 4-133-903-21 (NORWEGIAN)* 4-133-903-31 (DANISH)* 4-133-903-41 (THAI)* 4-133-903-51 (MALAY)* 4-133-903-61 (TURKISH)* 4-133-903-71 (GREEK)* 4-133-903-81 (UKRAINIAN)*

4-133-903-91 (CROATIAN)* 4-133-904-11 (ROMANIAN)* 4-133-904-21 (INDONESIAN)

Battery Charger(BC-CSGB/CSGC/CSGD/CSGE)0 1-480-175-31

(E (Southeast Asia))(BC-CSGD/CSGE)0 1-487-142-31

(EXCEPT US, CND,E (Southeast Asia), BR)

Battery Charger(BC-CSGD/CSGE)0 1-487-142-21 (US, CND)

USB, A/V Cable forMulti-use Terminal

1-836-364-11

(Note) (Note)Rechargeable Battery PackNP-BG1/Battery Case0 A-1567-198-A (US, CND)0 A-1641-431-A (EXCEPT US, CND)

Checking supplied accessories.

Refer to page 5-1 for mark 0.

Note: This item is supplied with the unit as an accessory, but isnot prepared as a service part.

7/28/2019 SONY DSC h20_sm[1]

49/58

HARDWARE LIST (1/9)

#1: M1.7 X 2.5(Black)2-635-562-11

2.5

1.7

#10:M1.7 X 4.0(Silver)2-599-475-31

1.6

1.7

#6: M1.4 X 1.7(Silver)2-598-474-01

1.7

1.4

#7: M1.7 X 1.6(Black)7-627-552-18

#3: M1.7 X 2.5(Red)2-660-401-01

2.5

1.7

#2: M1.7 X 4.0(Black)2-635-562-31

4.0

1.7

4.0

1.7

#5: M1.7 X 3.5 (Tapping)(Black)3-080-204-01

3.5

1.7

#4: M1.4 X 2.5 (Tapping)(Dark Silver)3-348-998-81

2.5

1.4

#12: M1.7 X 5.0 (Tapping)(Black)3-080-204-21

1.7

#9: M1.7 X 5.0 (Tapping)(Silver)3-078-890-21

5.0

1.7

#14:M1.7 X 2.5(Silver)2-599-475-11


2.5

1.7



3.5

1.7

4.0

1.7

5.0

2.5

#17:M1.7 X 1.5(Silver)2-586-389-01

2.5

1.7

#15:M1.4 X 1.5(Silver)3-062-214-01

1.5

1.4 1.4

#16:M1.4 X 2.5(Silver)2-586-337-01

1.5

3.5

1.7 2.2

#18:M1.4 X 2.5(Silver)2-635-591-21

2.5

1.4

#19: M1.2 X 4.0 (Tapping)(Red)3-086-156-21

4.0

1.2

#20:M1.4 X 3.0(Silver)2-635-591-31

3.0

1.4

7/28/2019 SONY DSC h20_sm[1]

50/58

HARDWARE LIST (2/9)

#21:M1.4 X 3.0(Black)2-662-396-21

3.0

1.4


1.7

5.0

1.7

5.5

#23: M1.7 X 4.0 (Tapping)(Black)3-080-204-11

4.0

1.7

#24: B1.7 X 5.5 (Tapping)(Black)4-679-805-11

#25:M1.7 X 3.0(Black)2-635-562-21

3.0

1.7

#26:M1.4 X 2.0(Silver)2-635-591-11

2.0

1.4

#27:M1.4 X 2.0(Black)2-662-396-11

2.0

1.4


1.4

4.0

#29:M1.4 X 2.5(Black)2-662-396-01

#31:M3.0 X 4.0(Silver)2-102-434-01

2.5

1.4

#30: M1.2 X 3.5 (Tapping)(White)3-086-156-11

3.5

1.2


#33:M3.0 X 6.0(Silver)3-077-331-21


#34:M3.0 X 8.0(Black)3-077-331-41

#36:M3.0 X 6.0(Silver)4-886-821-11

#37: M2.0 X 6.0 (Tapping)(Black)3-080-206-31



#39: M2.6 X 5.0 (Tapping)(Black)7-685-791-09

4.0

3.0

4.5

2.0

6.0

3.0

8.0

3.0 4.0

6.0 6.0

3.0

6.0

2.0

20.0

3.0

4.0

2.0

5.0

2.6

7/28/2019 SONY DSC h20_sm[1]

51/58

HARDWARE LIST (3/9)


8.0

3.0


2.0

4.0

#43:M1.7 X 4.0(Red)2-660-401-31

4.0

1.7

#46:M1.7 X 3.0(Red)2-660-401-11

#45:M1.4 X 2.5(Silver)2-587-151-01


3.0

1.4


3.0

1.7

3.0

1.7

2.5

1.4

#48:M1.7 X 2.5(Silver)3-973-497-91

2.5

1.7

#49:M2.0 X 4.0(Black)2-630-005-31

#50:M2.0 X 3.0(Red)2-891-494-11

#51:M2.0 X 2.5(Silver)3-073-686-01

#54: M1.75 X 6.0 (Tapping)(Black)3-318-203-11

#53: M2.0 X 5.0 (Tapping)(Black)3-080-206-21

#55:M2.0 X 4.0(Silver)2-655-582-11

#52: M2.0 X 4.0 (Tapping)(Black)3-080-206-11

#56:M2.0 X 3.5(Silver)3-067-187-11

4.0

2.0

3.0

2.0

2.5

2.0

5.0

2.0

4.0

2.0

6.0

1.75

4.0

2.0

3.5

2.0

#57:M1.7 X 4.0(Black)7-627-852-18

4.0

1.7


6.0

2.0


#60:M2.6 X 5.0(Black)3-061-062-11

5.0

2.0

5.0

2.6

7/28/2019 SONY DSC h20_sm[1]

52/58

HARDWARE LIST (4/9)

#61:M3.0 X 10.0(Black)7-682-549-09

10.0

3.0

#62:M2.0 X 3.0(Silver)3-080-202-21

3.0

2.0

#63:M5.0 X 12.5(Black)3-060-811-21

12.5

5.0


5.0

1.7

#65:M1.4 X 3.5(Silver)2-635-591-01

3.5

1.4

#66:M1.4 X 1.4(Silver)2-635-591-41

1.4

1.4

#71:M1.4 X 2.0(Red)3-208-537-01

2.0

1.4

2.0

1.4

2.0

1.4

#67:M1.4 X 2.0(Silver)3-389-523-16

2.0

1.4

#68:M1.7 X 4.0(Silver)2-655-581-01

4.0

1.7

#72:M1.4 X 2.0(Silver)4-663-621-41

2.0

1.4

#69:M1.7 X 3.0(Silver)2-599-475-21

3.0

1.7

#70:M1.7 X 5.0(Silver)2-599-475-41

5.0

1.7



#73: M1.2 X 4.0 (Tapping)(Black)3-086-156-61


#78:M1.4 X 3.5(Red)3-208-537-11

#79:M1.4X 2.0(Silver)2-587-151-11

#80:M1.4X 2.0(Black)3-279-411-01

6.0

1.7

3.5

1.7

4.0

1.7

4.0

1.2


5.0

1.2

3.5

1.4

7/28/2019 SONY DSC h20_sm[1]

53/58

HARDWARE LIST (5/9)

#81:M1.7 X 2.5(Silver)2-515-756-01

2.5

1.7

#82:M1.4 X 1.4(Silver)3-272-251-01

1.4

1.4

#83: M1.7 X 7.0 (Tapping)(Black)3-080-204-41

#84:M2.0 X 3.0(Silver)3-072-453-11

#85:M1.7 X 2.5(Black)2-515-483-11


4.0

1.7

#87:M1.6 X 5.3(Black)2-689-328-01

5.3

1.6


5.9

1.6


5.0

2.0

#90:M1.7 X 3.0(Silver)3-271-395-01

3.0

1.7


#92:M2.0 X 3.9(Black)3-268-954-01

3.9

2.0


#94:M1.7 X 4.0(Black)2-515-483-31

1.7

7.0 3.0

2.0

2.5

1.7

4.0

1.7

3.5

1.7

3.5

1.7

#95:M3.0 X 8.0 (Tapping)(Black)7-685-646-79

8.0

3.0

#99:M2.5 X 6.0 (Tapping)(Silver)3-776-750-02

6.0

2.5

#96:M1.4 X 2.5(Silver)2-587-151-21

2.5

1.4

#97:M1.4 X 2.5(Black)2-662-396-31

2.5

1.4

#98:M3.0 X 8.0(Silver)3-077-331-01

8.0

3.8

#100: M2.0 X 6.0(Black)3-080-203-51

6.0

2.0

7/28/2019 SONY DSC h20_sm[1]

54/58

HARDWARE LIST (6/9)

#101: M2.0 X 5.0(Silver)7-621-555-39

5.0

2.0

#107: M2.0 X 5.0(Silver)3-032-750-01

5.0

2.0

#108: M1.7 X 3.0 (Tapping)(Black)2-695-430-01

#111: M1.7 X 4.0 (Tapping)(Black)2-887-124-01

#102: M2.6 X 8.0(Black)7-621-284-30

8.0

2.6

#105: M2.0 X 4.0(Red)2-891-494-31

#106: M2.0 X 6.0(Black)3-713-786-11

#103: M2.6 X 10.0(Silver)7-685-794-09

10.0

2.6

#104: M3.0 X 8.0(Black)7-682-548-09

8.0

3.0

6.0

2.6

4.0

2.0

6.0

2.0

3.0

1.7

#109: M1.7 X 3.0(Black)2-515-483-21

3.0

1.7

3.0

2.0

#110: M2.0 X 3.0(Black)2-630-005-21

4.0

1.7


5.5

2.0

#112: M1.4 X 5.0(Black)2-178-410-11

5.0

1.4

#113: M1.7 X 5.0(Black)2-635-562-41

5.0

1.7


1.4

3.5


3.5

2.0


#118: M1.4 X 2.0(Black)2-655-580-01

4.5

1.7

2.0

1.4

#119: M2.6 X 5.0(Black)7-627-556-58

5.0

2.6

#120: M2.6 X 6.0(Silver)7-621-770-67

7/28/2019 SONY DSC h20_sm[1]

55/58

HARDWARE LIST (7/9)


#123: M4.0 X 8.0(Black)7-682-561-09

8.0

4.0

6.0

3.0

#122: M3.0 X 6.0(Black)7-682-547-09

#125: M1.4 X 3.0(Black)3-291-847-01

#129: M3.0 X 12.0(Black)7-682-550-09

4.0

2.0

2.0

12.0

1.7

4.0

#124: M1.7 X 2.0(Silver)2-599-475-01

#126: M2.9 X 3.5(Black)3-292-616-01

#134: M2.6 X 7.0(Black)3-299-572-01

#133: M3.0 X 6.0(Black)3-452-484-01

#131: M4.0 X 12.0(Silver)3-452-471-01


#132: M2.6 X 6.0(Black)4-673-655-01

#127: M3.0 X 25.0(Black)7-682-654-09

#128: M4.0 X 12.0(Black)3-452-472-01

3.0

3.5

6.0

25.0

1.4 2.9 3.04.0

12.0

3.0

#135: M2.0 X 2.5(Black)7-627-553-28

2.57.0

12.06.0

6.0

2.02.6

4.0 2.6

3.0

4.5

2.0

#136: M1.4 X 4.0 (Tapping)(Black)3-065-509-11

#137: M1.7 X 3.0(Black)3-090-976-62

4.0

1.4

3.0

1.7

#138: M1.4 X 3.5(Silver)4-104-078-01

3.5

1.4

#139: M1.4 X 2.0(Silver)2-655-579-01

#140: M1.7 X 2.0(Black)2-635-562-01

2.0

1.4

2.0

1.7

7/28/2019 SONY DSC h20_sm[1]

56/58

HARDWARE LIST (8/9)

5.0

2.6


#142: M1.4 X 2.0(Silver)4-111-392-01

2.0

1.4

#143: M1.4 X 2.0(Black)4-111-392-11

2.0

1.4

#144: M1.4 X 1.2(Silver)4-111-392-21

1.2

1.4

#145: M1.4 X 2.4(Silver)4-111-248-01

2.4

1.4

#146: M1.4 X 2.4(Black)4-111-248-11

2.4

1.4

3.5

1.4

#147: M1.4 X 3.5(Black)2-662-396-41

#148: M1.7 X 3.0(Silver)3-057-082-21

3.0

1.7


#153: M1.4 X 1.5(Silver)3-059-718-01

7.5

1.6

#150: M1.4 X 3.0(Black)4-105-150-01

3.0

1.4

2.5

1.4

#152: M1.4 X 2.5(Black)4-116-473-11

#151: M1.4 X 1.4(Silver)3-272-251-11

1.4

1.4

1.5

1.4

8.0

2.6

#154: M2.6 X 8.0(Silver)7-627-556-97

1.7

6.0

#155: M1.7 X 6.0 (Tapping)(Black)3-080-204-31

1.7

5.0

#156: M1.4 X 4.0(Silver)2-635-591-61

5.0

1.7

#157: M1.7 X 5.0 (Tapping)(Black)4-132-562-01

#158: M1.7 X 5.0(Red)2-660-401-51

4.0

1.4

#159: M1.4 X 4.0(Black)2-662-396-51

4.0

1.4

3.0

1.4

#160: M1.4 X 3.0(Silver)4-139-851-01

7/28/2019 SONY DSC h20_sm[1]

57/58

HARDWARE LIST (9/9)

3.0

1.4

#161: M1.4 X 3.0(Black)4-139-852-01

7/28/2019 SONY DSC h20_sm[1]

58/58

Revision History

Reverse

Ver.

1.0

1.1

Date

2009.03

2009.04

History

Official Release

Revised-1(A1 09-011)

Contents

Correction of Service Note Correction of Block Diagrams

S.M. revised: Page 1-5,Page 3-1, Page 3-4

S.M. Rev.

issued

Yes

985268332.pdf

sony dsc h20_sm[1]

Documents