soltaro ess all-in-one user manual
TRANSCRIPT
SOLTARO ESS ALL-IN-ONE
USER MANUAL
In order to secure the full 10-year product warranty, the Soltaro All-In-One ESS must be
installed by qualified installers.
WARNING: Read this entire document before installing or using Soltaro All-in-
one ESS. Failure to do so or to follow any of the instructions or warnings in
this document can result in electrical shock, serious injury, or death, or can
damage Soltaro ALL IN ONE ESS, potentially rendering it inoperable.
PRODUCT SPECIFICATIONS:
All specifications and descriptions in this document are verified to be accurate at the
time of printing. However due to continuous improvements, we reserve the right to make
product modifications at any time.
The images provided in this document are for demonstration purposes only. Depending
on product version and market region, details may appear differently.
ERRORS OR OMISSIONS:
To communicate any inaccuracies or omissions in this manual, please send an email
ELECTRONIC DEVICE – DO NOT DISPOSE OF INCORRECTLY
Proper disposal of batteries is required. Refer to your local codes for
disposal requirements.
All information in this document is subject to copyright and other intellectual
property rights of Wuxi Soltaro Energy Technology Co., Ltd . and its licensors.
This material may not be modified, reproduced or copied, in whole or in part,
without the prior written permission of Wuxi Soltaro Energy Technology Ltd. and
its licensors. Additional information is available upon request. The Soltaro Logo
and following are trademarks or registered trademarks of Wuxi Soltaro Energy
Technology Ltd. in Australia, UK and other countries.
SOLTARO SOLTATO BATTERY SOLTARO ESS
SAVE THESE IMPORTANT SAFETY DOCUMENTS:
Soltaro All-in-one ESS installation and repair instructions assume
knowledge of high voltage electricity and should only be performed by
Soltaro Certified Installers. Soltaro assumes no liability for injury or
property damage due to repairs attempted by unqualified individuals or
a failure to properly follow these instructions. These warnings and
cautions must be followed when using Soltaro ESS.
.
SYMBOLS IN THIS DOCUMENT:
This document uses the following symbols to highlight important information.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in injury or death.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in damage to the equipment.
NOTE
NOTE indicates an important step or tip that leads to best
results, but is not safety or damage related.
GENERAL INFORMATION:
Warning: Read this entire document before installing or
using Soltaro All-in-one ESS. Failure to do so or to follow
any of the instructions or warnings in this document
can result in electrical shock, serious injury, or death, or
can damage Soltaro LFP Battery, potentially rendering it
inoperable.
Warning: A battery can present a risk of electrical shock,
fire, or explosion from vented gases. Observe proper
precautions.
Warning: Soltaro LFP Battery installation must be carried out by
Soltaro Certified Installers, who have been trained in dealing with
high voltage electricity.
Warning: The Soltaro ESS is Heavy – lift with caution.
Warning: Use Soltaro ESS only as directed.
Warning: Do not use Soltaro ESS Battery if it is defective, appears
cracked, broken, or otherwise damaged, or fails to operate.
Warning: Before beginning the wiring portion of the installation, first
power off the inverter and then open the AC and DC disconnect
switches (is applicable to the installation).
Warning: Do not attempt to open, disassemble, repair, tamper with,
or modify Soltaro ESS. Soltaro ESS is not user serviceable. LFP
Cells in Soltaro Battery are not replaceable. Contact the Soltaro
Authorized reseller who sold the unit for any repairs.
Warning: Do not connect Soltaro ESS Battery to alternating current
carrying conductors. Soltaro ESS Battery must be wired to either an
inverter or a DC combiner panel that is then wired to an inverter. No
other wiring configuration may be used.
Warning: Soltaro LFP Battery contains components, such as
switches and relays, that can produce arcs or sparks.
Warning: To protect Soltaro ESS Battery and its components from
damage when transporting, handle with care. Do not impact, pull,
drag, or step on the unit. Do not subject the unit to any strong force.
To help prevent damage, leave Soltaro ESS in it’s shipping
packaging until it is ready to be installed.
Warning: Do not insert foreign objects into any part of the Soltaro
ESS All-In-One.
Warning: Do not expose the Soltaro ESS All-In-One to any direct
flame.
Warning: Do not install Soltaro ESS near heating equipment.
Warning: Do not immerse the Soltaro ESS All-In-One unit into water
or any fluids.
Caution: Do not use cleaning solvents to clean the Soltaro ESS, or
expose Soltaro ESS to flammable or harsh chemicals or vapours.
Caution: Do not use fluids, parts, or accessories other than those
specified in this manual, including use of non-genuine Soltaro parts
or accessories, or parts or accessories purchased from parties other
than Soltaro or a Soltaro Authorised reseller.
Caution: Do not use cleaning solvents to clean the Soltaro ESS, or
expose Soltaro ESS to flammable or harsh chemicals or vapours.
Caution: Do not place Soltaro ESS in a storage condition for more
than one (1) month, or permit the electrical feed on the Soltaro ESS
All-In-One unit to be severed for more than one (1) month, without
placing the Soltaro ESS into a storage condition in accordance with
Soltaro’s storage specifications.
Caution: Do not paint any part of the Soltaro All-In-One ESS
including any internal or external components such as the exterior
shell or casing.
Caution: Do not connect Soltaro ESS battery directly to PV Solar
wiring.
Caution: When installing Soltaro All-In-One ESS in a garage or near
vehicles. Keep out of driving path. If possible, install the Soltaro ESS
on a side wall and or above the height of vehicle bumpers.
ENVIRONMENTAL CONDITIONS:
Warning: Install Soltaro All-In-One ESS at a height that prevents
damage from flooding.
Warning: Operating or storing Soltaro ESS Battery in temperatures
outside it’s specified range might cause damage to Soltaro ESS.
Warning: Do not expose the Soltaro ESS to ambient temperatures
above 60C (140F) or below -30C (-22F).
Caution: Ensure that no water sources are above or near Soltaro
ESS, including downspouts, sprinklers, or faucets.
THE FUTURE OF SUSTAINABLE ENERGY:
Soltaro All-in-one ESS is a lithium-ion(LiFePO4) battery system that
turns solar panels into an all-day resource while offering backup
power in the event of a grid outage. Soltaro All-in- one ESS enables
storage of renewable energy, allowing optimized home energy
control and an increasing amount of total electricity production to
come from renewable sources. Reliable renewable energy improves
the resiliency of the grid, reduces energy costs, and increases the
impact of electric vehicle ownership.
POWER WHEN NEEDED:
Soltaro All-in-one ESS enables the storage of energy from solar
panels during the day, or from the grid when energy rates are low;
discharges energy for backup or use at night; and automatically
optimizes home energy. Soltaro All-in-one ESS thereby maximizes
solar consumption and reduces energy spending.
A FLEXABLE SOLUTION:
Soltaro All-in-one ESS can be charged from solar or grid power
and can provide backup power.
If greater amounts of energy are needed, multiple Soltaro All-in-
one ESS can be installed together to work as a larger system.
SOLTARO ALL-IN-ONE ESS
Technical Specifications
DEVICE SHORT NAMEPV STRING INPUT (DC)Max. DC Input Power [W]Max. DC Input Voltage [V]MPPT Voltage Range [V]Max. input current [A]Max. short circuit current [A]NO. of MPP TrackersStrings per MPP TrackerGalvanic Isola�on for PV Modules
BATTERY INPUT SIDEBa�ery CapacityNominal Ba�ery VoltageBa�ery Voltage RangeGalvanic Isola�on for Ba�eryMax. Charge CurrentMax. Discharge CurrentProtec�onDepth of Discharge
GRID AC OUTPUT(ON-GRID)Nominal Apparent Power Output to U�lity Grid [VA]Maximum Apparent Power Output to U�lity Grid [VA]Max. Apparent Power from U�lity Grid [VA]Nominal Output Voltage [V]Nominal Output Frequency [HZ]Max. AC Current Output to U�lity Grid [A]Max. AC Current From U�lity Grid [A]Output Power FactorOutput THDi [@Nominal Output]
EPS AC OUTPUT DATA(BACK-UP)Max. Output Apparent Power [VA]Peak Output Apparent [VA]Max. Output Current [A]Nominal Output Voltage [V]Nominal Output Frequency [HZ]Output THDv [@Linear Load]
EFFICIENCYMPPT EfficiencyEuro EfficiencyMax. EfficiencyMax. Ba�ery to Load EfficiencyStandby Power LossesTopology
PROTECTIONAn�-islanding Protec�onPV S�ng Input Reverse Polarity Protec�onInsula�on Resistor Dec�onResidual Current Monitoring UnitOutput Over Current Protec�onOutput Short Protec�onOutput Over Voltage Protec�on
GENERAL DATADC SwitchDimensions(W*H*D)(mm)Net Weight(KG)Protec�on DegreeMoun�ng Informa�onOpera�on Temperature Range [ C]Noise Emission (typical) [dB]User InterfaceCommunica�on with BMSCommunica�on with MeterCommunica�on with PortalRela�ve Humidity [%]Site Al�tude [m]Cooling Concept
CERTIFICATIONS& STANDARDSGrid Regula�onSafety Regula�onEMC StandardWARRANTY
Hyper-3KW
3900W580V125V~500V12.0A15.0A12NO
LiFePO4 4.5KWH/9KWH/13.5KWH/18KWH/22.5KWH48V40-60VYES60A60A Over Voltage, Less Voltage, Over Current, Short Circuit, Over Temperature Lithium-ion: 0~100% DOD Adjustable, Lead-acid: 0~50% DOD Adjustable
3000 VA3000 VA6000 VA230 V50/60 HZ16 A32 A ~1 (Adjustable from 0.8 leading to 0.8 lagging)<3%
3000VA4.5KVA, 10S; 9KVA, 100MS16 A230(±2%)50/60(±2%)<3%
99.9%97.0%97.8%95%<0.5WHigh Frequency Isola�on
YESYESYESYESYESYESYES
Op�onal414*N/1242/145mm66KG/104KG/142KGIP 65Wall Bracket-20 C~+60 C(45 C dera�ng)<25dbAPPRS 485 & CANRS 485Wi-Fi0~95%<4000mNatural Convec�on
VDE-AR-N 4105, VDE0126-1-1, AS4777.2, G83/2, G59, CEI 0-21, NRS 097-2-1, En50438IEC/EN62109-1&2, IEC62040-1EN61000-6-1, EN61000-6-2, EN61000-6-3, EN61000-6-4, EN61000-4-16, EN61000-4-18, EN61000-4-295-10 years standard warranty (dependƛƴƎ ƻƴ NJŜƎƛƻƴύ
Hyper-3.68KW
4600W580V125V~500V11.0A/11.0A14.0A/14.0A21NO
48V40-60VYES60!60A
3680 VA3680 VA7360 VA230 V50/60 HZ16A32A
<3%
3680 VA5.52KVA, 10S; 11KVA, 100MS16 A230(±2%)50/60(±2%)<3%
99.9%97.0%97.8%95%<0.5WHigh Frequency Isola�on
YESYESYESYESYESYESYES
Op�onal414*N/1374/145mm66KG/104KG/142KGIP 65Wall Bracket-20 C~+60 C(45 C dera�ng)<25dbAPPRS 485 & CANRS 485Wi-Fi0~95%<4000mNatural Convec�on
Hyper-5KW
6500W580V125V~500V11.0A/11.0A14.0A/14.0A21NO
48V40-60VYES100A100A
рл00 VA5100 VA9200 VA230 V50/60 HZ24.5 A40 A
<3%
5000 VA6.5 KVA, 10S; 15 KVA, 100MS21.7 A230(±2%)50/60(±2%)<3%
99.9%97.0%97.8%95%<0.5WHigh Frequency Isola�on
YESYESYESYESYESYESYES
Op�onal414*N/1374/145mm73KG/111KG/149KGIP 65Wall Bracket-20 C~+60 C(45 C dera�ng)<25dbAPPRS 485 & CANRS 485Wi-Fi0~95%<4000mNatural Convec�on
∗1: N is the numbers of ba�ery modules.
∗2
∗3
∗2:
∗3: 21.7A for AS4777.2 . ∗4: Can be reached only if PV and ba�ery power is enough.∗5: The standard configura�on is CAN.
∗1
∗1
∗4
∗5
*1
4600 for VDE 0126-1-1 &VDE-AR-N4105, 4950 for AS4777.2; 4050 for CEI 0-21
www.Soltaro.com Made In China
STANDARD PACKING LIST:
HYBRID / AC COUPLED INVERTER 2 KWH / 4.5 KWH LFP BATTERY
INVERTER BACKSHEET BATTERY BACKSHEET INVERTER HOLDER INVERTER POSITIONER
BATTERY INVERTER
POWER CABLES
25 MM 2BA
BATTERY INVERTER
COMMUNICATION
CABLE RJ45
M6 EXPANSION
SCREWS
M5 / M4 / M8
HEXAGON SOCKET
HEAD CAP SCREW
STEP 1: CONFIRM THE EXACT MOUNTING POSITION OF BATTERY BACKSHEET
STEP 2: HANGING ON THE BATTERY MODULE TO THE MOUNTED BATTERY
BACKSHEET
STEP 3: SELECT THE CORRECT INVERTER BACK-POSITIONER TO THE
INVERTER BRACKET
STEP 4: INSTALL THE INVERTER BRACKET
STEP 5: INSTALL BATTERY POWER CABLE AND COMMUNICATION CABLE
STEP 6: FIX THE CABLE COVER ONTO BATTERY
STEP 7: MOUNTING THE INVERTER
STEP 8: SCREW THE WATERPROOF TERMINALS ONTO INVERTER HOLDER
STEP 9: CABLE CONNECTION INSIDE SOLTARO ALL-IN-ONE ESS
STEP 10: BATTERY & INVERTER SETTING
Please refer to the following manuals:
HYPER HYBRID INVERTER MANUAL (www.soltaro.com/documentation)
AC RETRO INVERTER MANUAL (www.soltaro.com/documentation)
STEP 11: HOW TO START THE SYSTEM
Please refer to the following manuals
HYPER HYBRID INVERTER MANUAL (www.soltaro.com/documentation)
AC RETRO INVERTER MANUAL (www.soltaro.com/documentation)
When ready to power on the battery, please refer to the following steps -
STEP 12: MOUNT CABLE COVER
NORMAL OPERATION:
During normal operation, if Soltaro All-In-One ESS is installed correctly, the inverter and
battery will start communication immediately, then begin to process power commands.
See the inverter manual for further configuration instructions.
Warning: Do not operate Soltaro All-In-One ESS unless all overs are
in place.
Warning: Do not disconnect anything from or add anything to Soltaro
All-In-One ESS.
Caution: Do not try to communicate with Soltaro ESS using 3rd party
tools or diagnostics between Soltaro ESS Battery and Inverter.
Caution: Do not lean on, stack anything on top of, or hang anything
from Soltaro ESS All-In-One or associated wiring and conduit.
SOLTARO ALL-IN-ONE ESS CARE:
Keep all surfaces of the Soltaro All-In-One ESS clear of obstruction to maintain optimum
air flow.
To clean Soltaro All-In-One ESS, use a soft lint-free cloth. The cloth can be dampened
with clean water if needed.
Caution: Do not use cleaning solvents to clean the Soltaro All-In-One
ESS or associated wiring and conduit.