sleeper / sofa: affina, laresta - ki · sleeper / sofa: affina, laresta a .steel b. wood c. foam d....

Required Tools Disassembly Instructions Material Type: Page 1 of 3 Rev. 0 P0033-0012 KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com Sleeper / Sofa: Affina, LaResta Page 1 of 3 Rev. 0 P0033-0012 A .Steel B. Wood C. Foam D. Plastic E. Fabric F. Aluminum/Alloy KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com Procedure: 1. Pull out any drawers if present and remove all steel slides, brackets and hardware from the drawers. 2. Remove all screws holding bed frame, arms, or storage arms and set these larger assemblies aside. 3. Separate bed back and seat from frame and arms or side sup- ports 4. Dismantle storage arms. Remove door, alloy hinges, aluminum door pulls, veneer or laminated top caps, internal plastic liner panels and all steel brackets. 5. Dismantle back and seat, separating wood from metal components. WARNING: DAMPING CYLINDER IS UNDER PRESSURE! HANDLE WITH CAUTION. 6. Cut and remove any fabric from the seat and back. 7. Cut away or scrape any foam from seat and back to expose any steel hardware or brackets. Any actuator cables may be cut for removal. Recycle aluminum and alloy actuator handle components. 8. Remove plastic rollers from bed frame and plastic leg glides from legs. 9. Separate all remaining steel from wood components and recycle or discard as required. General Notes: 1. Disassembly time: 50-60 minutes 2. This procedure assumes basic familiarity with hand tools and 3. All materials removed and disassembled shall be sorted and furniture terminology: no specialized training is required segregated with like materials and disposed of or recycled according to recycling availability or waste acceptance 4. For items to be recycled, refer to KI's End of Life Recycling Matrix and KI's End of Life Recovery Options Matrix, available at www.ki.com All fasteners not explicitly tagged or shown are Material Type A: Steel Gloves Safety Glasses Pry Bar Allen Wrench Claw Hammer Utility Knife Putty Knife Philips Screwdriver

Upload: lamlien

Post on 11-Jul-2018

213 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: Sleeper / Sofa: Affina, LaResta - KI · Sleeper / Sofa: Affina, LaResta A .Steel B. Wood C. Foam D. Plastic E. Fabric F. Aluminum/Alloy Procedure: 1. Pull out any drawers if present

RequiredTools

Disassembly Instructions

Material Type:

Warning: This drawing format requires special non-standard fonts!!Make sure the appropriate font files are installed!!!

TT Humanst 521 BT LightO HelveticaLTStd-Cond

O HelveticaLTStd-LightCond

Page 1 of 3Rev. 0 P0033-0012 KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com

Sleeper / Sofa: Affina, LaResta

Page 1 of 3Rev. 0 P0033-0012

A .Steel B. Wood C. Foam D. Plastic E. Fabric F. Aluminum/Alloy

KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com

Procedure: 1. Pull out any drawers if present and remove all steel slides, brackets and hardware from the drawers. 2. Remove all screws holding bed frame, arms, or storage arms and set these larger assemblies aside. 3. Separate bed back and seat from frame and arms or side sup- ports 4. Dismantle storage arms. Remove door, alloy hinges, aluminum door pulls, veneer or laminated top caps, internal plastic liner panels and all steel brackets. 5. Dismantle back and seat, separating wood from metal components. WARNING: DAMPING CYLINDER IS UNDER PRESSURE! HANDLE WITH CAUTION. 6. Cut and remove any fabric from the seat and back. 7. Cut away or scrape any foam from seat and back to expose any steel hardware or brackets. Any actuator cables may be cut for removal. Recycle aluminum and alloy actuator handle components. 8. Remove plastic rollers from bed frame and plastic leg glides from legs. 9. Separate all remaining steel from wood components and recycle or discard as required.

General Notes: 1. Disassembly time: 50-60 minutes 2. This procedure assumes basic familiarity with hand tools and

3. All materials removed and disassembled shall be sorted and furniture terminology: no specialized training is required

segregated with like materials and disposed of or recycled according to recycling availability or waste acceptance 4. For items to be recycled, refer to KI's End of Life Recycling Matrix and KI's End of Life Recovery Options Matrix, available at www.ki.com

All fasteners not explicitly tagged orshown are Material Type A: Steel

Gloves Safety Glasses Pry Bar Allen Wrench Claw HammerUtility Knife Putty Knife Philips Screwdriver