sitronix st7920 - pucelj.sirs rw e db7 db0 to db3 half size character rom (hcgrom) 1024x16 bits...

ST Sitronix ST7920 Chinese Fonts built in LCD controller/driver

V4.0 1/49 2008/08/18

Main Features l Operation Voltage Range:

ÿ 2.7V to 5.5V l Support 8-bit, 4-bit and serial bus MPU interface l 64 x 16-bit display RAM (DDRAM)

ÿ Supports 16 words x 4 lines (Max) ÿ LCD display range 16 words x 2 lines

l 64 x 256-bit Graphic Display RAM (GDRAM) l 2M-bits Character Generation ROM (CGROM):

Support 8192 Chinese words (16x16 dot matrix) l 16K-bit half-width Character Generation ROM

(HCGROM): Supports 126 characters (16x8 dot matrix)

l 32-common x 64-segment (2 lines of character) LCD drivers

l Automatic power on reset (POR) l External reset pin (XRESET) l With the extension segment drivers, the display

area can up to 16x2 lines l Built-in RC oscillator:

Frequency is adjusted by an external resistor

l Low power consumption design ÿ Normal mode (450uA Typ VDD=5V) ÿ Standby mode (30uA Max VDD=5V)

l VLCD (V0 to VSS): max 7V l Graphic and character mixed display mode l Multiple instructions:

ÿ Display Clear ÿ Return Home ÿ Display ON/OFF ÿ Cursor ON/OFF ÿ Display Character Blink ÿ Cursor Shift ÿ Display Shift ÿ Vertical Line Scroll ÿ Reverse Display (by line) ÿ Standby Mode

l Built-in voltage booster (2 times) VOUT: max 7V

l 1/33 Duty (with ICON)

Function Description ST7920 LCD controller/driver IC can display alphabets, numbers, Chinese fonts and self-defined characters. It supports 3 kinds of bus interface, namely 8-bit, 4-bit and serial. All functions, including display RAM, Character Generation ROM, LCD display drivers and control circuits are all in a one-chip solution. With a minimum system configuration, a Chinese character display system can be easily achieved. ST7920 includes character ROM with 8192 16x16 dots Chinese fonts and 126 16x8 dots half-width alphanumerical fonts. Besides, it supports 64x256 dots graphic display area for graphic display (GDRAM). Mix-mode display with both character and graphic data is possible. ST7920 has built-in CGRAM and provide 4 sets software programmable 16x16 fonts. ST7920 has wide operating voltage range (2.7V to 5.5V). It also has low power consumption. So ST7920 is suitable for battery-powered portable device. ST7920 LCD driver consists of 32-common and 64-segment. Company with the extension segment driver (ST7921) ST7920 can support up to 32-common x 256-segment display.

Part Number Font Code ST7920-0A BIG-5 Code Set (Traditional Chinese) ST7920-0B GB Code Set (Simplified Chinese) ST7920-0C Chinese (Traditional/Simplified) & Japanese ST7920-0F Chinese (Traditional/Simplified), Japanese & Korean

ST7920

V4.0 2/49 2008/08/18

ST7920 Specification Reversion History Version Date Description

C1.7 2000/12/15

1. VCC changed to VDD. 2. VLCD changed from VCC-V5 to V0-VSS. 3. DC characteristics input High voltage (Vih) changed to 0.7VDD. 4. DC characteristics output High voltage (Voh) changed to 0.8VDD.

C1.8 2001/03/01

1. Chip Size changed. 2. ICON 256 dots changed to 240 dots. 3. XOFF normal high sleep Low changed to normal low sleep High. 4. Added XOFF application. 5. Modified application of ST7920: PIN 4~6 are floating. (PIN 4~6 are test pin) 6. Modified voltage doubler CAP1P, CAP1M, CAP2M capacitors polarity

C1.9 2001/05/28

1. Icon RAM TABLE changed. (TABLE-6) 2. Booster description modified. (PAGE-29) 3. AC Characteristics modified. 4. Added 2Line 16 Chinese Word (32Com X 256Seg) application circuit. 5. Added oscillation resistor’s relation to power consumption and frequency.

C2.0 2001/07/03 1. Added Register initial values. 2. Voltage booster CAP1M CAP1P polarity changed (PAGE-30).

V2.0 2001/08/17 1. Modified Table 7 (PAGE-14). 2. Change to English version.

V2.0c 2001/10/18 1. Modified page-38 Serial interface timing diagram.

V2.0d 2002/05/09 1. Add the standard code (Japan, GB code, BIG-5 code).

V3.0 2002/10/11 1. Delete sleep mode function.

V3.1 2003/04/11 1. Modified GDRAM Address (AC5…AC0, 00h…3Fh).

V3.2 2003/09/09 1. Add the CGROM and HCGROM test application circuit.

V3.3 2004/03/29 1. Updat the using method for ICON.

V3.4 2005/5/24 1. ICON no used.

V3.5 2005/5/24 1. Add VOUT voltage limitation. 2. Remove IRAM related descriptions.

V3.6 2005/6/6 1. Fix the check sum count number on Page 28~30.

655360->655362, 10240->10242. 2. Modify the description about serial interface.

V3.7 2007/7/24 1. Add CGROM/HCGROM checksum operation time. V3.8 2007/12/20 1. Add “Clear DDRAM” step before check sum process. V3.9 2008/3/3 1. Modify 4-bit initial sequence.

V4.0 2008/8/18 1. Add Font Code “0F” at Page 1. 2. Modify the description of Font Code Table at Page 1.

ST7920

V4.0 3/49 2008/08/18

System Block Diagram

Timing

Generator

33/49-bit

shift

register

Common

Signal

Driver

Display

Data RAM

(DDRAM)

64 x 16 bits

64-bit

latch

circuit

Segment

Signal

Driver

64-bit

shift

register

LCD Drive

Voltage

Selector

CLK

Instruction

Register (IR)

Instruction

Decoder

Reset

Circuit

MPU

Interface

Input/

Output

Buffer

Address

Counter

Character

Generator

ROM

(CGROM)

2M bits

Character

Generator

RAM

(CGRAM)

1024 bits

Cursor

Blink

Scroll

Controller

Data

Register

(DR)

Busy

Flag

Parallel/Serial converter

and

Attribute Circuit

VDD

V0 V1 V2 V3 V4

RESI RESO CL1 CL2 M

DOUT

COM1 to COM32

SEG1 to SEG64

RS

RW

E

DB4 to DB7

DB0 to DB3

Half size

Character

ROM

(HCGROM)

1024x16 bits

XRESET

Graphic

RAM

(GDRAM)

1024 x 16

bits

XOFF

Vss

PSB

ST7920

V4.0 4/49 2008/08/18

Pad Diagram

Origin: center of chip Coordinates: from pad center Chip size: 5305 X 4074 Pad open: 90 X 90 Pad pitch: 125 unit: μm * Chip substrate must connect to VSS

98 69

136

30

31

1

68 99

ST7920 “ST7920

(0,0)

1

ST7920

V4.0 5/49 2008/08/18

PAD Coordinates (Unit: um)

No. Name X Y 1 V0 -2548 1812 2 V1 -2548 1688 3 V2 -2548 1562 4 CLK -2548 1438 5 TT1 -2548 1312 6 TT2 -2548 1188 7 V3 -2548 1062 8 V4 -2548 938 9 VSS -2548 812 10 VDD -2548 688 11 XRESET -2548 562 12 CL1 -2548 438 13 CL2 -2548 312 14 VDD -2548 188 15 M -2548 62 16 DOUT -2548 -62 17 RS -2548 -188 18 RW -2548 -312 19 E -2548 -438 20 VSS -2548 -562 21 OSC1 -2548 -688 22 OSC2 -2548 -812 23 PSB -2548 -938 24 D0 -2548 -1062 25 D1 -2548 -1188 26 D2 -2548 -1312 27 D3 -2548 -1438 28 D4 -2548 -1562 29 D5 -2548 -1688 30 D6 -2548 -1812 31 D7 -2306 -1933 32 XOFF -2181 -1933 33 VOUT -2056 -1933 34 CAP3M -1931 -1933 35 CAP1P -1806 -1933 36 CAP1M -1681 -1933 37 CAP2P -1556 -1933 38 CAP2M -1431 -1933

No. Name X Y 39 VD2 -1306 -1933

40 C[1] -1181 -1933

41 C[2] -1056 -1933

42 C[3] -931 -1933

43 C[4] -806 -1933

44 C[5] -681 -1933

45 C[6] -556 -1933

46 C[7] -431 -1933

47 C[8] -306 -1933

48 C[9] -181 -1933

49 C[10] -56 -1933

50 C[11] 69 -1933

51 C[12] 194 -1933

52 C[13] 319 -1933

53 C[14] 444 -1933

54 C[15] 569 -1933

55 C[16] 694 -1933

56 C[17] 819 -1933

57 C[18] 944 -1933

58 C[19] 1069 -1933

59 C[20] 1194 -1933

60 C[21] 1319 -1933

61 C[22] 1444 -1933

62 C[23] 1569 -1933

63 C[24] 1694 -1933

64 C[25] 1819 -1933

65 C[26] 1944 -1933

66 C[27] 2069 -1933

67 C[28] 2194 -1933

68 C[29] 2319 -1933

69 C[30] 2548 -1812

70 C[31] 2548 -1688

71 C[32] 2548 -1562

72 C[33] Not use 2548 -1438

73 S[64] 2548 -1312

74 S[63] 2548 -1188

75 S[62] 2548 -1062

76 S[61] 2548 -938

ST7920

V4.0 6/49 2008/08/18

No. Name X Y 77 S[60] 2548 -812 78 S[59] 2548 -688 79 S[58] 2548 -562 80 S[57] 2548 -438 81 S[56] 2548 -312 82 S[55] 2548 -188 83 S[54] 2548 -62 84 S[53] 2548 62 85 S[52] 2548 188 86 S[51] 2548 312 87 S[50] 2548 438 88 S[49] 2548 562 89 S[48] 2548 688 90 S[47] 2548 812 91 S[46] 2548 938 92 S[45] 2548 1062 93 S[44] 2548 1188 94 S[43] 2548 1312 95 S[42] 2548 1438 96 S[41] 2548 1562 97 S[40] 2548 1688 98 S[39] 2548 1812 99 S[38] 2319 1933 100 S[37] 2194 1933 101 S[36] 2069 1933 102 S[35] 1944 1933 103 S[34] 1819 1933 104 S[33] 1694 1933 105 S[32] 1569 1933 106 S[31] 1444 1933 107 S[30] 1319 1933 108 S[29] 1194 1933 109 S[28] 1069 1933 110 S[27] 944 1933 111 S[26] 819 1933 112 S[25] 694 1933 113 S[24] 569 1933 114 S[23] 444 1933 115 S[22] 319 1933

No. Name X Y 116 S[21] 194 1933 117 S[20] 69 1933 118 S[19] -56 1933 119 S[18] -181 1933 120 S[17] -306 1933 121 S[16] -431 1933 122 S[15] -556 1933 123 S[14] -681 1933 124 S[13] -806 1933 125 S[12] -931 1933 126 S[11] -1056 1933 127 S[10] -1181 1933 128 S[9] -1306 1933 129 S[8] -1431 1933 130 S[7] -1556 1933 131 S[6] -1681 1933 132 S[5] -1806 1933 133 S[4] -1931 1933 134 S[3] -2056 1933 135 S[2] -2181 1933 136 S[1] -2306 1933

ST7920

V4.0 7/49 2008/08/18

Pin Description Name No. I/O Connects to Function

XRESET 11 I ― System reset input (low active).

PSB 23 I ― Interface selection: 0: serial mode; 1: 8/4-bit parallel bus mode.

RS(CS*) 17 I MPU

Parallel Mode: Register select. 0: Select instruction register (write) or busy flag, address counter (read); 1: Select data register (write/read). Serial mode: Chip select. 1: chip enabled; 0: chip disabled. When chip is disabled, SID and SCLK should be set as “H” or “L”. Transcient of SID and SCLK is not allowed.

RW(SID*) 18 I MPU

Parallel Mode: Read/Write control. 0: Write; 1: Read. Serial Mode: Sserial data input.

E(SCLK*) 19 I MPU Parallel Mode: 1: Enable trigger. Serial Mode: Serial clock.

D4 to D7 28~31 I/O MPU Higher nibble data bus of 8-bit interface and data bus for 4-bit interface D0 to D3 24~27 I/O MPU Lower nibble data bus of 8-bit interface.

CL1 12 O Extension segment drv. Latch signal for extension segment drivers.

CL2 13 O Extension segment drv. Shift clock for extension segment drivers.

M 15 O Extension segment drv. AC signal for extension segment drivers voltage inversion.

DOUT 16 O Extension segment drv. Data output for extension segment drivers. COM1 to COM32 40~71 O LCD Common signals.

SEG1 to SEG64 136~73 O LCD Segment signals.

V0 to V4 1~3,7,8 ― ― LCD bias voltage. V0 ~ V4 ≦ 7V. VDD 10,14 I Power VDD : 2.7V to 5.5V. Vss 9,20 I Power VSS: 0V.

OSC1, OSC2 21,22 I, O Resistors

Using internal oscillator: 5.0V R=33K; 2.7V R=18K. Using external clock: Use OSC1 as external clock input.

VOUT 33 O Resistors LCD voltage doubler output. VOUT ≦ 7V. *Note: The OSC pin must have the shortest wiring pattern of all other pins. To prevent noise from other signal lines, it should also be enclosed by the largest GND pattern. Poor anti-noise characteristics on the OSC line will result in malfunction, or adversely affect the clock’s duty ratio.

ST7920

V4.0 8/49 2008/08/18

Pin Description (continued)

Name No. I/O Connects to Description CAP3M CAP1P CAP1M CAP2M

34 35 36 38

I/O Capacitors Capacitor pins for voltage doubler Voltage ≦ 7V.

XOFF 32 O ― Reserved (no connection). CAP2P 37 ― ― Reserved (no connection). C[33] 72 O ― Reserved (no connection).

VD2 39 I Reference voltage

Voltage doubler reference voltage. If use internal voltage doubler, please make sure that: l VD2 ≦ 3.5V or l VOUT ≦ 7V and CAP3M ≦ 7V.

CLK TT1 TT2

4 5 6

I ― ― ―

For CGROM/HCGROM checksum. Refer to checksum application.

Note: 1. 7V>=VOUT>=V0>=V1>=V2>=V3>=V4 must be maintained 2. Two clock options: As shown below.

External Resistor vs. Current

(VDD=5V)

0

100

200

300

400

500

600

700

800

5 15 25 40 60 80 100Resistor(K)

Iss

(uA)

External Resistor vs. Frequency(VDD=5V)

0

100

200

300

400

500

600

700

800

900

5 15 25 40 60 80 100Resistor(K)

Freq

uenc

y(K

Hz)

3. When using voltage doubler (VOUT), it is recommended that the sum of those divide resistors (R1~R5) should be larger than 20K Ohm.

So that the voltage doubler can provide sufficient power.

R=33K (VDD=5.0V) R=18K (VDD=2.7V)

R OSC1 OSC2 OSC1 OSC2

Clock input

ST7920

V4.0 9/49 2008/08/18

Voltage Doubler

Vss

CAP1M

Voltage DoublerReference Voltage

CAP1P

CAP2M

CAP2P

CAP3M

VOUT

VD2

VOUT

VOUT vs. VD2

0

1

2

3

4

5

6

7

8

9

10

5 4.8 4.6 4.4 4.2 4 3.8 3.6 3.4 3.2 3 2.8 2.6 2.4 2.2 2 1.8VD2 (V)

VO

UT

(V)

Voltage Doubler mode: VD2 & Vout output characteristic Notes: l Total resistance of the Follower deviding resistors should larger than 20K Ohm. l Booster Capacitor uses 4.7uF l Panel size: 80mm x 28mm (check display)

Do not operate in this area.

ST7920

V4.0 10/49 2008/08/18

Function Description

System interface

ST7920 supports 3 kinds of bus interface to communicate with MPU: 8-bit parallel, 4-bit parallel and clock synchronized serial interface. Parallel interface is selected by PSB=”1” and serial interface is by PSB=”0”. 8-bit / 4-bit interface is selected by function set instruction DL bit. Two 8-bit registers (Data Register DR and Instruction Register IR) are used in ST7920 to access DRAM or Register. Data Register (DR) can access DDRAM, CGRAM and GDRAM through the address pointer implemented by Address Counter (AC). Instruction Register (IR) stores the instruction sent by MPU to ST7920. 4 kinds of parallel interface access mode can be selected through RS and RW:

RS RW Description L L MPU write instruction to instruction register (IR) L H MPU read busy flag (BF) and address counter (AC) H L MPU write data to data register (DR) H H MPU read data from data register (DR)

* The serial interface access modes do not have Read operation.

Busy Flag (BF)

ST7920 needs a process time for any received instruction. Before finishing the received instruction, any further instruction is not accepted. The process time of each instruction is not equal and the internal process is finished or not can be determined by the BF. Internal operation is in progress while BF=”1”, that means ST7920 is in busy state. No further instructions will be accepted until BF=”0”. MPU must check BF to determine whether the internal operation is finished or not before issuing instruction.

Address Counter (AC)

Address Counter (AC) is used as the address pointer of DDRAM, CGRAM and GDRAM. (AC) can be set by instruction. After that, accesses (Read/Write operations) to the memories, such as DDRAM, CGRAM or GDRAM, (AC) will be increased or decreased by 1 (according to the setting in “Entry Mode Set” Register). When RS=”0”, RW=”1” and E=”1” the value of (AC) will be output to DB6~DB0.

Character Generation ROM (CGROM) and Half-width Character Generation ROM (HCGROM)

ST7920 is built in a Character Generation ROM (CGROM) to provide 8192 16x16 character fonts and a Half-width Character Generation ROM to provide 126 8x16 alphanumeric characters. It is easy to support multi-language applications such as Chinese and English. Two consecutive bytes are used to specify one 16x16 character or two 8x16 half-width characters. Character codes are written into DDRAM and the corresponding fonts are mapped from CGROM or HCGROM to the display drivers.

Character Generation RAM (CGRAM)

ST7920 is built in a Character Generation RAM (CGRAM) to support user-defined fonts. Four sets of 16x16 bit-maped RAM spaces are available. These user-defined fonts are displayed the same ways as CGROM fonts by writing the related character code into the DDRAM.

ST7920

V4.0 11/49 2008/08/18

Display Data RAM (DDRAM)

There are 64x2 bytes RAM spaces for the Display Data RAM. It can store display data such as 16 characters (16x16) by 4 lines or 32 characters (8x16) by 4 lines. However, only 2 character-lines (maximum 32 common outputs) can be displayed at one time. Character codes stored in DDRAM will refer to the fonts specified by CGROM, HCGROM and CGRAM. ST7920 can display half-width HCGROM fonts, user-defined CGRAM fonts and full 16x16 CGROM fonts. The character codes in 0000H~0006H will use user-defined fonts in CGRAM. The character codes in 02H~7FH will use half-width alpha numeric fonts. The character code larger than A1H will be treated as 16x16 fonts and will be combined with the next byte automatically. The 16x16 BIG5 fonts are stored in A140H~D75FH while the 16x16 GB fonts are stored in A1A0H~F7FFH. In short: 1. To display HCGROM fonts:

Write 2 bytes of data into DDRAM to display two 8x16 fonts. Each byte represents 1 character. The data is among 02H~7FH.

2. To display CGRAM fonts: Write 2 bytes of data into DDRAM to display one 16x16 font. Only 0000H, 0002H, 0004H and 0006H are acceptable.

3. To display CGROM fonts: Write 2 bytes of data into DDRAM to display one 16x16 font. A140H~D75FH are BIG5 code, A1A0H~F7FFH are GB code.

The higher byte (D15~D8) is written first and the lower byte (D7~D0) is the next. Please refer to Table 5 for the relationship between DDRAM and the address/data of CGRAM. CGRAM fonts and CGROM fonts can only be displayed in the start position of each address. (Refer toTable 4)

80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F H L H L H L H L H L H L H L H L H L H L H L H L H L H L H L H L S i t r o n i x S T 7 9 2 0 矽創電子 . . 中文編碼 ( 正確 ) 矽創電子 . . . 中文編碼

Table 4

Incorrect start position

ST7920

V4.0 12/49 2008/08/18

Graphic RAM (GDRAM)

Graphic Display RAM has 64x256 bits bit-mapped memory space. GDRAM address is set by writing 2 consecutive bytes of vertical address and horizontal address. Two-byte data (16 bits) configures one GDRAM horizontal address. The Address Counter (AC) will be increased by one automatically after receiving the 16-bit data for the next operation. After the horizontal address reaching 0FH, the horizontal address will be set to 00H and the vertical address will not change. The procedure is summarized below: 1. Set vertical address (Y) for GDRAM 2. Set horizontal address (X) for GDRAM 3. Write D15~D8 to GDRAM (first byte) 4. Write D7~D0 to GDRAM (second byte) Please refer to Table 7 for Graphic Display RAM mapping.

LCD driver

ST7920 embedded LCD driver has 33 commons and 64 segments to drive the LCD panel. Segment data from CGRAM, CGROM and HCGROM are shifted into the 64 bits segment latche to display. Extended segment driver (ST7921) can be used to extend the segment outputs upto 256 segments.

ST7920

V4.0 13/49 2008/08/18

DDRAM data (char. code)

CGRAM Addr.

CGRAM data (higher byte)

CGRAM data (lower byte)

B15~ B4 B3

B2

B1

B0

B5

B4

B3

B2

B1

B0

D15

D14

D13

D12

D11

D10

D9

D8

D7

D6

D5

D4

D3

D2

D1

D0

0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 0 1 1 1 1 1 1 0 0 1 0 0 0 0 1 0 0 1 0 0 1 0 0 0 0 1 0 0 0 1 0 1 0 0 1 1 1 1 0 0 1 0 0 0 0 1 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 1 1 0 0 1 0 0 1 0 0 0 1 0 0 0 0 0 1 0 0 1 0 0 0 1 0 1 0 0 0 0 1 0 0 1 0 0 1 0 0 1 0 0 0 0 0 1 0 0 0 0 1 0 1 0 0 0 1 0 0 1 0 0 0 0 1 0 0 0 0 0 1 0 1 1 0 0 1 1 1 1 0 0 0 0 1 0 0 0 0 0 1 1 0 0 0 0 1 0 0 1 0 0 0 1 0 0 0 0 0 0 1 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0

0 X 00 X 00

1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 1 0 0 0 0 1 0 0 1 1 0 1 0 0 0 0 1 1 0 1 0 1 1 1 0 1 1 0 1 0 0 1 0 0 0 1 0 0 1 0 0 0 0 0 0 0 1 0 1 0 0 1 0 0 0 1 0 1 0 1 1 1 1 1 1 1 0 0 1 0 0 1 0 0 0 1 1 0 0 1 0 0 0 0 0 1 0 0 1 0 0 1 0 0 0 1 1 1 0 1 1 1 1 1 1 1 0 0 1 0 0 1 0 0 1 0 0 0 0 1 0 0 0 0 0 1 0 0 1 0 0 1 0 0 1 0 0 1 0 1 1 1 1 1 1 1 0 0 1 0 0 1 0 0 1 0 1 0 0 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 1 0 1 1 0 1 1 1 1 1 1 1 1 0 0 0 1 0 0 1 1 0 0 1 0 1 0 0 0 0 0 1 0 1 0 0 1 0 0 1 1 0 1 1 0 1 1 1 1 1 1 1 0 0 1 1 1 0 0 1 1 1 0 1 0 1 0 0 0 0 0 1 0 0 0 1 0 0 0

0 X 01 X 01

1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Table 5: DDRAM data (character code) vs. CGRAM data/address map Note: 1. DDRAM data (character code) bit1 and bit2 are identical with CGRAM address bit4 and bit5. 2. CGRAM address bit0 to bit3 specify total 16 rows. Row-16 is for cursor display. The data in Row-16 will be logically OR to the cursor. 3. CGRAM data for each address is 16 bits. 4. To select the CGRAM font, the bit4 through bit15 of DDRAM data must be “0” while bit0 and bit3 are “don’t care”.

ST7920

V4.0 14/49 2008/08/18

Table 6 16x8 half-width characters

ST7920

V4.0 15/49 2008/08/18

（）GDRAM Horizontal address X

︵

︶

GD

RA

M V

ertical address Y

0 151 ...........0123456789

101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263

...........

...........

...........b14b15 b0b13

Table 7 GDRAM display coordinates and corresponding address

ST7920

V4.0 16/49 2008/08/18

Instructions ST7920 offers basic instruction set and extended instruction set:

Instruction Set 1: (RE=0: Basic Instruction)

Code Inst.

RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Exec time

(540KHZ)

Display Clear

0 0 0 0 0 0 0 0 0 1 Fill DDRAM with "20H" and set DDRAM address counter (AC) to "00H".

1.6 ms

Return Home

0 0 0 0 0 0 0 0 1 X Set DDRAM address counter (AC) to "00H", and put cursor to origin ；the content of DDRAM are not changed

72 us

Entry Mode Set

0 0 0 0 0 0 0 1 I/D S Set cursor position and display shift when doing write or read operation

72 us

Display Control

0 0 0 0 0 0 1 D C B D=1: Display ON C=1: Cursor ON B=1: Character Blink ON

72 us

Cursor Display Control

0 0 0 0 0 1 S/C R/L X X Cursor position and display shift control; the content of DDRAM are not changed

72 us

Function Set

0 0 0 0 1 DL X 0

RE X X

DL=1 8-bit interface DL=0 4-bit interface RE=1: extended instruction RE=0: basic instruction

72 us

Set CGRAM Address.

0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0 Set CGRAM address to address counter (AC) Make sure that in extended instruction SR=0 (scroll or RAM address select)

72 us

Set DDRAM Address.

0 0 1 0

AC6 AC5 AC4 AC3 AC2 AC1 AC0

Set DDRAM address to address counter (AC) AC6 is fixed to 0

72 us

Read Busy Flag (BF) & AC.

0 1 BF AC6 AC5 AC4 AC3 AC2 AC1 AC0 Read busy flag (BF) for completion of internal operation, also Read out the value of address counter (AC)

0 us

Write RAM 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Write data to internal RAM (DDRAM/CGRAM/GDRAM)

72 us

Read RAM 1 1 D7 D6 D5 D4 D3 D2 D1 D0 Read data from internal RAM (DDRAM/CGRAM/GDRAM)

72 us

ST7920

V4.0 17/49 2008/08/18

Instruction set 2: (RE=1: extended instruction)

Code Inst.

RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Exec time

(540KHZ)

Standby 0 0 0 0 0 0 0 0 0 1 Enter standby mode, any other instruction can terminate. COM1…32 are halted.

72 us

Scroll or RAM

Address. Select

0 0 0 0 0 0 0 0 1 SR SR=1: enable vertical scroll position SR=0: enable CGRAM address (basic instruction)

72 us

Reverse (by line)

0 0 0 0 0 0 0 1 R1 R0 Select 1 out of 4 line (in DDRAM) and decide whether to reverse the display by toggling this instruction R1,R0 initial value is 0,0

72 us

Extended Function

Set 0 0 0 0 1 DL X

1 RE

G 0

DL=1 :8-bit interface DL=0 :4-bit interface RE=1: extended instruction set RE=0: basic instruction set G=1 :graphic display ON G=0 :graphic display OFF

72 us

Set Scroll Address

0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0 SR=1: AC5~AC0 the address of vertical scroll 72 us

Set Graphic Display RAM

Address

0 0 1 0 0

0 AC5

0 AC4

AC3 AC3

AC2 AC2

AC1 AC1

AC0 AC0

Set GDRAM address to address counter (AC) Set the vertical address first and followed the horizontal address by consecutive writings Vertical address range: AC5…AC0 Horizontal address range: AC3…AC0

72 us

Note: 1. Make sure that ST7920 is not in busy state by reading the busy flag before sending instruction or data. If using delay loop instead, please

make sure the delay time is enough. Please refer to the instruction execution time. 2. “RE” is the selection bit of basic and extended instruction set. After setting the RE bit, the value will be kept. So that the software doesn’t

have to set RE every time when using the same instruction set.

ST7920

V4.0 18/49 2008/08/18

Initial Setting (Register flag) (RE=0: basic instruction)

Code Inst.

RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description

0 0 0 0 0 0 0 1 I/D S Entry Mode Set 1 0

Cursor move to right ,DDRAM address counter (AC) plus 1

0 0 0 0 0 0 1 D C B Display Control

0 0 0 Display, cursor and blink are ALL OFF

0 0 0 0 0 1 S/C R/L X X CURSOR DISPLAY

SHIFT X X No cursor or display shift operation

0 0 0 0 1 DL X 0

RE X X FUNCTION

SET 1 0

8-bit MPU interface , basic instruction set

Initial Setting (Register flag) (RE=1: extended instruction set)

Code Inst.

RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description

0 0 0 0 0 0 0 0 1 SR SCROLL OR RAM ADDR.

SELECT 0

Allow vertical scroll or set CGRAM address

0 0 0 0 0 0 0 1 R1 R0 REVERSE

0 0 Begin with normal and toggle to reverse

0 0 0 0 1 DL X 1

RE G 0 EXTENDED

FUNCTION SET 0

Graphic display OFF

ST7920

V4.0 19/49 2008/08/18

Description of basic instruction set

l Display Clear

This instruction will change the following items: 1. Fill DDRAM with "20H"(space code). 2. Set DDRAM address counter (AC) to"00H". 3. Set Entry Mode I/D bit to be "1". Cursor moves right and AC adds 1 after write or read operation.

l Return Home

Set address counter (AC) to "00H". Cursor moves to origin. Then content of DDRAM is not changed. l Enry Mode Set

Set the cursor movement and display shift direction when doing write or read operation. I/D: Address Counter Control: (Increase/Decrease) When I/D = "1", cursor moves right, address counter (AC) is increased by 1. When I/D = "0", cursor moves left, address counter (AC) is decreased by 1. S: Display Shift Control: (Shift Left/Right)

S I/D DESCRIPTION H H Entire display shift left by 1 H L Entire display shift right by 1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

Code

Code

Code

RS

RS

RS

RW

RW

RW

DB7

DB7

DB7

DB6

DB6

DB6

DB5

DB5

DB5

DB4

DB4

DB4

DB1

DB1

DB1

DB2

DB2

DB2

DB3

DB3

DB3

0

1

I/D

1

X

S

DB0

DB0

DB0

ST7920

V4.0 20/49 2008/08/18

l Display Control

Controls display, cursor and blink ON/OFF. D: Display ON/OFF control bit When D = "1", display ON When D = "0", display OFF, the content of DDRAM is not changed C: Cursor ON/OFF control bit When C = "1", cursor ON. When C = "0", cursor OFF. B: Character Blink ON/OFF control bit When B = "1", cursor position blink ON. Then display data (character) in cursor position will blink. When B = "0", cursor position blink OFF

l Cursor/Display Shift Control

This instruction configures the cursor moving direction or the display shifting direction. The content of DDRAM is not changed.

S/C R/L Description AC Value L L Cursor moves left by 1 position AC=AC-1 L H Cursor moves right by 1 position AC=AC+1 H L Display shift left by 1, cursor also follows to shift. AC=AC H H Display shift right by 1, cursor also follows to shift. AC=AC

0

0

0

0

0

0

0

0

0

0

0

1

1

S/C

D

R/L

Code

Code

RS

RS

RW

RW

DB7

DB7

DB6

DB6

DB5

DB5

DB4

DB4

DB1

DB1

DB2

DB2

DB3

DB3

C

X

B

X

DB0

DB0

ST7920

V4.0 21/49 2008/08/18

l Function Set

DL: 4/8-bit interface control bit When DL = "1", 8-bit MPU bus interface When DL = "0", 4-bit MPU bus interface RE: extended instruction set control bit When RE = "1", extended instruction set When RE = "0", basic instruction set In same instruction cannot alter DL and RE at once. Make sure that change DL first then RE.

l Set CGRAM Address

Set CGRAM address into address counter (AC) AC range is 00H…3FH Make sure that in extended instruction SR=0 (scroll address or RAM address select)

l Set DDRAM Address

Set DDRAM address into address counter (AC). First line AC range is 80H…8FH Second line AC range is 90H…9FH Third line AC range is A0H…AFH Fourth line AC range is B0H…BFH Please note that only 2 lines can be display with one ST7920.

l Read Busy Flag (BF) and Address

Read busy flag (BF) can check whether the internal operation is finished or not. At the same time, the value of address counter (AC) is also read. When BF = “1”, further instruction(s) will not be accepted until BF = “0”.

0 0 0 0 1 DL X RE Code

RS RW DB7 DB6 DB5 DB4 DB1 DB2 DB3

X X

DB0

0 1 BF AC6 AC5 AC4 AC3 AC2 Code


AC1 AC0

DB0

0 0 0 1 AC5 AC4 AC3 AC2 Code


AC1 AC0

DB0

0 0 1 AC6 AC5 AC4 AC3 AC2 Code


AC1 AC0

DB0

ST7920

V4.0 22/49 2008/08/18

l Write Data to RAM

Write data to the internal RAM and increase/decrease the (AC) by 1 Each RAM address (CGRAM, DDRAM and GDRAM…) must write 2 consecutive bytes for 16-bit data. After receiving the second byte, the address counter will increase or decrease by 1 according to the entry mode set control bit.

l Read RAM Data

Read data from the internal RAM and increase/decrease the (AC) by 1 After the operation mode changed to Read (CGRAM, DDRAM and GDRAM…), a “Dummy Read” is required. There is no need to add a “Dummy Read” for the following bytes unless a new address set instruction is issued.

1

1

0

1

D7

D7

D6

D6

D5

D5

D4

D4

D3

D3

D2

D2

Code

Code

RS

RS

RW

RW

DB7

DB7

DB6

DB6

DB5

DB5

DB4

DB4

DB1

DB1

DB2

DB2

DB3

DB3

D1

D1

D0

D0

DB0

DB0

ST7920

V4.0 23/49 2008/08/18

Description of extended instruction set

l Standby

This Instruction will set ST7920 entering the standby mode. Any other instruction follows this instruction will terminate the standby mode. The content of DDRAM remains the same.

l Vertical Scroll or RAM Address Select

When SR = "1", the Vertical Scroll mode is enabled. When SR = "0", “Set CGRAM Address” instruction (basic instruction) is enabled.

l Reverse

Select 1 out of 4 lines to reverse the display and to toggle the reverse condition by repeating this instruction. R1, R0 initial vale is 00. The first time issuing this instruction, the display will be reversed while the second time will return the display become normal.

R1 R0 Description L L First line normal or reverse L H Second line normal or reverse H L Third line normal or reverse H H Fourth line normal or reverse

Please note that only 2 lines out of 4 lines of display data can be displayed with one ST7920.

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

Code

Code

Code

RS

RS

RS

RW

RW

RW

DB7

DB7

DB7

DB6

DB6

DB6

DB5

DB5

DB5

DB4

DB4

DB4

DB1

DB1

DB1

DB2

DB2

DB2

DB3

DB3

DB3

0

1

R1

1

SR

R0

DB0

DB0

DB0

ST7920

V4.0 24/49 2008/08/18

l Extended Function Set

DL: 4/8-bit interface control bit When DL = "1", 8-bit MPU interface. When DL = "0", 4-bit MPU interface. RE: extended instruction set control bit When RE = "1", extended instruction set When RE = "0", basic instruction set G: Graphic display control bit When G = "1", Graphic Display ON When G = "0", Graphic Display OFF In same instruction cannot alter DL, RE and G at once. Make sure that change DL or G first and then RE.

l Set Scroll Address

SR=1: AC5~AC0 is vertical scroll displacement address

l Set Graphic RAM Address

Set GDRAM address into address counter (AC). This is a 2-byte instruction. The first instruction sets the vertical address while the second one sets the horizontal address (write 2 consecutive bytes to complete the vertical and horizontal address setting). Vertical address range is AC5...AC0 Horizontal address range is AC3…AC0 The address counter (AC) of graphic RAM (GRAM) will be increased automatically after the vertical and horizontal addresses are set. After horizontal address is increased upto 0FH, it will automatically return to 00H. However, the vertical address will not increase as the result of the same action.

0 0 0 0 1 DL X RE Code


G X

DB0



AC1 AC0

DB0

0 0 1 0 0 0 AC3 AC2 Code


AC1 AC0

DB0



AC1 AC0

DB0

ST7920

V4.0 25/49 2008/08/18

Parallel interface: ST7920 is in parallel mode by pulling up PSB pin. ST7920 can select 8-bit or 4-bit bus interface by setting the DL control bit in “Function Set” instruction. MPU can control RS, RW, E and DB0…DB7 pins to complete the data transmission. In 4-bit transfer mode, every 8-bit data or instruction is separated into 2 parts. The higher 4 bits (bit-7~bit-4) data will be transfered first through data pins (DB7~DB4). The lower 4 bits (bit-3~bit-0) data will be transfered second through data pins (DB7~DB4). The (DB3~DB0) data pins are not used during 4-bit transfer mode.

Timing Diagram of 8-bit Parallel Bus Mode Data Transfer

RS

RW

E

DB0-DB7

Dummy read Instruction write RAM read

Timing Diagram of 4-bit Parallel Bus Mode Data Transfer

RS

RW

E Upper Lower Upper Lower Upper Lower

DB0-DB7

Dummy read Instruction write RAM read

4-bit 4-bit 4-bit 4-bit 4-bit 4-bit

ST7920

V4.0 26/49 2008/08/18

Serial interface: ST7920 is in serial interface mode when pulling down PSB pin. Two pins (SCLK and SID) are used to complete the data transfer. Only write data is available in the serial interface mode. When chip select (CS) is low, ST7920 serial clock counter and serial data will be reset. Serial transfer counter is set to the first bit and data register is cleared. After CS is “L”, any further change on SID or SCLK is not allowed. It is recommended to keep SCLK at “L” and SID at the last status before set CS to “L”. For a minimal system with only one ST7920 and one MPU, only SCLK and SID pins are necessary. CS pin should pull to high. ST7920’s serial clock (SCLK) is asynchronous to the internal clock and is generated by MPU. When multiple instruction/data is transferred, the instruction execution time must be considered. MPU must wait till the previous instruction is finished and then send the next instruction. ST7920 has no internal instruction buffer area. When starting a transmission, a start byte is required. It consists of 5 consecutive “1” (sync character). Serial transfer counter will be reset and synchronized. Followed by 2-bit flag that indicates: read/write (RW) and register/data selected (RS) operation. Last 4 bits are filled by “0”. After receiving the sync character, RW and RS bits, every 8 bits instruction/data will be separated into 2 groups. Higher 4 bits (DB7~DB4) will be placed in the first section followed by 4 “0”s. And lower 4 bits (DB3~DB0) will be placed in the second section followed by 4 “0”s.

1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

1 1 1 1 1 RW RS 0 D7 D6 D5 D4 0 0 0 0 0 0 0 0 D3 D2 D1 D0

CS

SCLK

SID

Synchronizing Bit string

Higher data

Lower data

3

1st byte 2nd byte

Timing Diagram of Serial Mode Data Transfer

ST7920

V4.0 27/49 2008/08/18

8051 demo program for serial interface ;-------------------------------------------------------------- ; Write data from A into INSTRUCTION Register ;-------------------------------------------------------------- WRINS: SETB CS SETB SID ; SID = 1 CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.7 ; SID = A.7 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.6 ; SID = A.6 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.5 ; SID = A.5 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.4 ; SID = A.4 SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.3 ; SID = A.3 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.2 ; SID = A.2 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.1 ; SID = A.1 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.0 ; SID = A.0 SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK CLR CS CALL DLY8 RET

;------------------------------------------------- ; Write data from A into DATA Register ;------------------------------------------------- WRDATA: SETB CS SETB SID ; SID = 1 CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SID ; SID = 1 SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.7 ; SID = A.7 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.6 ; SID = A.6 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.5 ; SID = A.5 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.4 ; SID = A.4 SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.3 ; SID = A.3 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.2 ; SID = A.2 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.1 ; SID = A.1 SETB SCLK ; READ DATA FROM SID CLR SCLK MOVBIT SID, A.0 ; SID = A.0 SETB SCLK ; READ DATA FROM SID CLR SCLK CLR SID ; SID = 0 SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK SETB SCLK ; READ DATA FROM SID CLR SCLK CLR CS CALL DLY8 RET

ST7920

V4.0 28/49 2008/08/18

Application circuit for testing CGROM and HCGROM:

We can use the function of “CHECK SUM” to check the CGROM is right or error. See the following notes: Useing IC Pad (Pin4‡CLK, Pin5‡TT1, Pin6‡TT2) to do the “CHECK SUM” function. The application circuit is at Page49.

Timing Diagram for checking CGROM (TT1=0, TT2=1)

The ST7920 check sum process: (DDRAM must be cleared by 0x00 before this process) In the first place: Resetting the internal counter (set TT1 and TT2 to Height) In the second place: Setting CGROM mode (set TT1 to Low, TT2 to Height). In the third place: CLK starts to count 655362 times. In the final place: Finishing the counting, read the last four bytes to CHECK SUM (reading only when the CLK is Height). ST7920 check sum circuit: Data is available when CLK is height; if CLK is low then the data is always FFH. The last four bytes are Y0, Y1, Y2, and Y3.

The fatest execution time is: tCYC=1us (1MHz at 5V). The table below is a comparing table of CGROM for different versions.

CGROM Last four bytes Version (Font) Y0 Y1 Y2 Y3

1 Big5 (0A) 38 88 CC F1

2 GB (0B) 9D 81 79 29

3 0C FD 6F B5 85

ST7920

V4.0 29/49 2008/08/18

Timing Diagram for checking HCGROM (TT1=1, TT2=0)

The ST7920 check sum process: (DDRAM must be cleared by 0x00 before this process) In the first place: Resetting the internal counter (set TT1 and TT2 to Height) In the second place: Setting CGROM mode (set TT1 to Height, TT2 to Low). In the third place: CLK starts to count 10242 times. In the final place: Finishing the counting, read the last four bytes to CHECK SUM (reading only when the CLK is Height). ST7920 check sum circuit: Data is available when CLK is height; if CLK is low then the data is always FFH. The last four bytes are Y0, Y1, Y2, and Y3.

The fatest execution time is: tCYC=2us (0.5MHz at 5V). The table below is a comparing table of HCGROM for different versions.

HCGROM last four bytes Version (Font) Y0 Y1 Y2 Y3

1 Big5 (0A) B5 11 B5 11

2 GB (0B) B5 11 B5 11

3 0C B5 11 B5 11

ST7920

V4.0 30/49 2008/08/18

Testing Step: 1. Clear whole DDRAM area by writing data 0x00. 2. Composing TT1 and TT2 to make the ‘Reset’ action, and clear the internal counter. 3. Selecting the test mode by setting TT1 and TT2 (CGROM or HCGROM). 4. After setp1 and setp2, entering some impulse signals through Pin4 (CLK). 5. Reading the CHECK SUM data through D0 to D7. 6. Comparing CHECK SUM with the Code Table (upper table) to check if the data is correct or not.

TT1 TT2 No. of counts Status

1 1 -- RESET

0 1 655362 CGROM

1 0 10242 HGROM

Test process flow:

ST7920

V4.0 31/49 2008/08/18

8051 CGROM、HCGROM illustrative test program

;*******************************;

;* CHECK_ROM *;

;*******************************;

;*******************************;

;* Definition of outside Pin *;

;*******************************;

CLK REG P3.5 ;

TT1 REG P3.0 ;

TT2 REG P3.1 ;

TT3 REG P3.2 ;CHECK CGROM FLAG

TT4 REG P3.3 ;CHECK HCGROM FLAG

TT5 REG P3.4 ;ERROR FLAG

;*******************************;

;* Definition of internal RAM *;

;*******************************;

STACK EQU 6FH ;

FUNC EQU 20H ;

;*******************************;

; Interrupt set *;

;*******************************;

ORG 00H ;

AJMP RESET ;

;*******************************;

;* PROGRAM START *;

;*******************************;

RESET: MOV SP,#STACK ;

MOV P1,#FFH ;

MOV P3,#FFH ;

;*******************************;

;* CHECK_CGROM *;

;*******************************;

;*******************************;

;* Initial DDRAM *;

;*******************************;

CALL WR0x00 ;Write 0x00 to whole DDRAM

;*******************************;

;* Initial setting *;

;*******************************;

CGROM: SETB TT1 ;

SETB TT2 ;TT1,TT2 SET HIGH (RESET)

CALL DELAY_100US ;Wait Reset 100us

CLR TT1 ;TT1=LOW TT2=HIGH ( CHECK CGROM)

SETB CLK ;

CALL DELAY_100US ;

;*******************************;

;* start counter *;

;*******************************;

MOV R3,#9 ;

CN4: MOV R2,#0 ;

ST7920

V4.0 33/49 2008/08/18

N7: CLR CLK ; |

SETB CLK ; |

DJNZ R2,N7 ; |

;---------------------------------------;

ST7920

V4.0 34/49 2008/08/18

8-bit interface:

POWER ON

Wait time >40ms

XRESET LOW HIGH

Function set

RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

0 0 0 0 1 1 X 0 X X

Wait time >100uS

Function set


0 0 0 0 1 1 X 0 X X

Wait time >37uS

Display ON/OFF control


0 0 0 0 0 0 1 D C B

Wait time >100uS

Display clear


0 0 0 0 0 0 0 0 0 1

Wait time >10mS

Entry mode set


0 0 0 0 0 0 0 1 I/D S

Initialization end

ST7920

V4.0 35/49 2008/08/18

4-bit interface:

POWER ON

Wait time > 40mS(for VDD stable)

XRESET: LOW HIGH

Wait time > 100μS

Wait time > 100μS

Display ON/OFF ControlRS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Wait time > 100μS

INITIALIZATION END

Function setRS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Function setRS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB00 0 0 0 1 0 X X X X0 0 X 0 X X X X X X

0 0 0 0 1 0 X X X X0 0 X 0 X X X X X X

X X X XX X X X

0 0 0 0 0 00 0 1 D C B

Display ClearRS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Wait time > 10mS

X X X XX X X X

0 0 0 0 0 00 0 0 0 0 1

Entry Mode SetRS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

X X X XX X X X

0 0 0 0 0 00 0 0 1 I/D S

ST7920

V4.0 36/49 2008/08/18

Built in voltage booster

VSS

VD2


VOUT

Vss

CAP1M


CAP1P

CAP2M

CAP2P

CAP3M

VOUT

VD2

VOUT

External reset timing

XRESET pulse width Trw 10us RESET start time Tres 50ns

Tres

Trw

VDD

XRESET

ST7920

V4.0 37/49 2008/08/18

LCD driving wave form (1/33 duty, 1/5 bias )

When oscillation frequency is 540KHZ, 1 clock cycle time = 1.85us 1 frame = 1.85us x 300 x 33 = 18315us=18.3ms 1 2 3 4 33 1 2 3 4 33 1 2 3 4 33

V0 V1 V2

V3 V4

VSS

COM1

V0 V1 V2

V3 V4

VSS

COM2

V0 V1 V2

V3 V4

VSS

COM33

V0 V1 V2

V3 V4

VSS

SEGx off

V0 V1 V2

V3 V4

VSS

SEGx on

1 frame

300 clocks

ST7920

V4.0 38/49 2008/08/18

Absolute Maximum Ratings

Characteristics Symbol Value Power Supply Voltage VDD -0.3V to +6.0V

LCD Driver Voltage VLCD or V0 -0.3V to +7.0V Voltage Doubler Output VOUT -0.3V to +7.0V

Input Voltage VIN -0.3V to VDD+0.3V Operating Temperature TA -30℃ to + 85℃ Storage Temperature TSTO -65℃ to + 150℃

DC Characteristics (TA = -30℃ ~ 85℃, VDD = 2.7 V - 4.5 V)

Symbol Characteristics Test Condition Min. Typ. Max. Unit

VDD Operating Voltage - 2.7 - 5.5 V VLCD LCD Voltage V0-VSS 3.0 - 7 V

ICC Power Supply Current fOSC = 530KHz, VDD=3.0V

Rf=18KΩ - 0.20 0.45 mA

VIH1 Input High Voltage

(Except OSC1) - 0.7VDD - VDD V

VIL1 Input Low Voltage

(Except OSC1) - - 0.3 - 0.6 V


(OSC1) - VDD – 1 - VDD V


(OSC1) - - - 1.0 V

VOH1 Output High Voltage

(DB0 - DB7) IOH = -0.1mA 0.8VDD - VDD V

VOL1 Output Low Voltage

(DB0 - DB7) IOL = 0.1mA - - 0.1 V

VOH2 Output High Voltage (Except DB0 - DB7) IOH = -0.04mA 0.8VDD - VDD V

VOL2 Output Low Voltage (Except DB0 - DB7) IOL = 0.04mA - - 0.1VDD V

ILEAK Input Leakage

Current VIN = 0V to VDD -1 - 1 µA

IPUP Pull Up MOS Current VDD = 3V 22 27 32 µA

ST7920

V4.0 39/49 2008/08/18

DC Characteristics (TA = -30℃ ~ 85℃, VDD = 4.5 V - 5.5 V)

Symbol Characteristics Test Condition Min. Typ. Max. Unit

VDD Operating Voltage - 4.5 - 5.5 V VLCD LCD Voltage V0-VSS 3.0 - 7 V

ICC Power Supply Current fOSC = 540KHz, VDD=5V

Rf=33KΩ - 0.45 0.75 mA


(Except OSC1) - 0.7VDD - VDD V


(Except OSC1) - -0.3 - 0.6 V


(OSC1) - VDD-1 - VDD V


(OSC1) - - - 1.0 V

VOH1 Output High Voltage

(DB0 - DB7) IOH = -0.1mA 0.8VDD - VDD V

VOL1 Output Low Voltage

(DB0 - DB7) IOL = 0.1mA - - 0.4 V

VOH2 Output High Voltage (Except DB0 - DB7) IOH = -0.04mA 0.8VDD - VDD V

VOL2 Output Low Voltage (Except DB0 - DB7) IOL = 0.04mA - - 0.1VDD V

ILEAK Input Leakage

Current VIN = 0V to VDD -1 - 1 µA

IPUP Pull Up MOS Current VDD = 5V 75 80 85 µA

ST7920

V4.0 40/49 2008/08/18

AC Characteristics (TA = -30℃ ~ 85℃, VDD = 4.5V) Parallel Mode Interface

Symbol Characteristics Test Condition Min. Typ. Max. Unit Internal Clock Operation

fOSC OSC Frequency R = 33KΩ 480 540 600 KHz External Clock Operation

fEX External Frequency - 480 540 600 KHz Duty Cycle - 45 50 55 %

TR,TF Rise/Fall Time - - - 0.2 µs Write Mode (Writing data from MPU to ST7920)

TC Enable Cycle Time Pin E 1200 - - ns TPW Enable Pulse Width Pin E 140 - - ns

TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 10 - - ns TAH Address Hold Time Pins: RS,RW,E 20 - - ns

TDSW Data Setup Time Pins: DB0 - DB7 40 - - ns TH Data Hold Time Pins: DB0 - DB7 20 - - ns

Read Mode (Reading Data from ST7920 to MPU) TC Enable Cycle Time Pin E 1200 - - ns

TPW Enable Pulse Width Pin E 140 - - ns TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 10 - - ns TAH Address Hold Time Pins: RS,RW,E 20 - - ns TDDR Data Delay Time Pins: DB0 - DB7 - - 100 ns TH Data Hold Time Pins: DB0 - DB7 20 - - ns

Interface Mode with LCD Driver(ST7921) TCWH Clock Pulse with High Pins: CL1, CL2 800 - - ns TCWL Clock Pulse with Low Pins: CL1, CL2 800 - - ns TCST Clock Setup Time Pins: CL1, CL2 500 - - ns TSU Data Setup Time Pin: D 300 - - ns TDH Data Hold Time Pin: D 300 - - ns TDM M Delay Time Pin: M -1000 - 1000 ns

ST7920

V4.0 41/49 2008/08/18

AC Characteristics (TA = -30℃ ~ 85℃, VDD = 2.7V) Parallel Mode Interface




TR,TF Rise/Fall Time - - - 0.2 µs Write Mode (Writing data from MPU to ST7920)

TC Enable Cycle Time Pin E 1800 - - ns TPW Enable Pulse Width Pin E 160 - - ns

TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 10 - - ns TAH Address Hold Time Pins: RS,RW,E 20 - - ns

TDSW Data Setup Time Pins: DB0 - DB7 40 - - ns TH Data Hold Time Pins: DB0 - DB7 20 - - ns

Read Mode (Reading Data from ST7920 to MPU) TC Enable Cycle Time Pin E 1800 - - ns

TPW Enable Pulse Width Pin E 320 - - ns TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 10 - - ns TAH Address Hold Time Pins: RS,RW,E 20 - - ns TDDR Data Delay Time Pins: DB0 - DB7 - - 260 ns TH Data Hold Time Pins: DB0 - DB7 20 - - ns

Interface Mode with LCD Driver(ST7921) TCWH Clock Pulse with High Pins: CL1, CL2 800 - - ns TCWL Clock Pulse with Low Pins: CL1, CL2 800 - - ns TCST Clock Setup Time Pins: CL1, CL2 500 - - ns TSU Data Setup Time Pin: D 300 - - ns TDH Data Hold Time Pin: D 300 - - ns TDM M Delay Time Pin: M -1000 - 1000 ns

ST7920

V4.0 42/49 2008/08/18

8-bit interface timing diagram

l MPU write data to ST7920 l MPU read data from ST7920

Valid data

RS

R/W

E

DB0-DB7

VIH1VIL1TAS TAH

TAHTPWTR

TDDR TH

TCTC

Valid data

RS

R/W

E

DB0-DB7

VIH1VIL1TAS TAH

TAHTPW

TH

TCTC

TDSWTR

ST7920

V4.0 43/49 2008/08/18

AC Characteristics (TA = -30℃ ~ 85℃, VDD = 4.5V) Serial Mode Interface




TR,TF Rise/Fall Time - - - 0.2 µs

TSCYC Serial clock cycle Pin E 400 - - ns

TSHW SCLK high pulse width Pin E 200 - - ns TSLW SCLK low pulse width Pin E 200 - - ns TSDS SID data setup time Pins RW 40 - - ns TSDH SID data hold time Pins RW 40 - - ns TCSS CS setup time Pins RS 60 - - ns TCSH CS hold time Pins RS 60 - - ns

AC Characteristics (TA = -30℃ ~ 85℃, VDD = 2.7V) Serial Mode Interface




TR,TF Rise/Fall Time - - - 0.2 µs

TSCYC Serial clock cycle Pin E 600 - - ns

TSHW SCLK high pulse

width Pin E 300 - - ns

TSLW SCLK low pulse width Pin E 300 - - ns TSDS SID data setup time Pins RW 40 - - ns TSDH SID data hold time Pins RW 40 - - ns TCSS CS setup time Pins RS 60 - - ns

TCSH CS hold time Pins RS 60 - - ns

ST7920

V4.0 44/49 2008/08/18

Serial interface timing diagram

l MPU write data to ST7920

Valid data

CS

SID

SCLK

TCSS TCSH

TSCYC

TSLWTSHW

TSDSTr

TSDH

Tf

ST7920

V4.0 45/49 2008/08/18

I/O pin diagram

Input PAD: E (No Pull-up) Input PAD: RS, RW (with Pull-up)

Output PAD: CL1, CL2, M, D

I/O PAD: DB0 – DB7

DATA

Enable

ST7920

V4.0 46/49 2008/08/18

Application circuit 1: LCD : 32-COM x 160-SEG LCD Voltage : VCC

1 2 3 4 5 6

A

B

C

D

654321

D

C

B

A

Title

Number RevisionSize

B

Date: 1-Mar-2001 Sheet of File: D:\Buffer-2\7920V1.DDB Drawn By:

V01

V12

V23

VXA4

VXB5

VXC6

V37

V48

VSS9

VDD10

XRESET11

CL112

CL213

VDD14

M15

DOUT16

RS17

RW18

E19

VSS20

OSC121

OSC222

PSB23

D024

D125

D226

D327

D428

D529

D630

D7

31

XO

FF32

VO

UT

33

CAP3

M34

CAP1

P35

CAP1

M36

CAP2

P37

CAP2

M38

VD

239

C140

C241

C342

C443

C544

C645

C746

C847

C948

C10

49

C11

50

C12

51

C13

52

C14

53

C15

54

C16

55

C17

56

C18

57

C19

58

C20

59

C21

60

C22

61

C23

62

C24

63

C25

64

C26

65

C27

66

C28

67

C29

68

C30 69C31 70C32 71C33 72S64 73S63 74S62 75S61 76S60 77S59 78S58 79S57 80S56 81S55 82S54 83S53 84S52 85S51 86S50 87S49 88S48 89S47 90S46 91S45 92S44 93S43 94S42 95S41 96S40 97S39 98

S38

99S3

710

0S3

610

1S3

510

2S3

410

3S3

310

4S3

210

5S3

110

6S3

010

7S2

910

8S2

810

9S2

711

0S2

611

1S2

511

2S2

411

3S2

311

4S2

211

5S2

111

6S2

011

7S1

911

8S1

811

9S1

712

0S1

612

1S1

512

2S1

412

3S1

312

4S1

212

5S1

112

6S1

012

7S9

128

S812

9S7

130

S613

1S5

132

S413

3S3

134

S213

5S1

136

U1

ST7920

S50

1

S51

2

S52

3

S53

4

S54

5

S55

6

S56

7

S57

8

S58

9

S59

10

S60

11

S61

12

S62

13

S63

14

S64

15S6

516

S66

17

S67

18

S68

19

S69

20

S70

21

S71

22

S72

23

S73

24

S74

25

S75

26

S76

27

S77

28

S78

29

S79

30

S80

31

S81

32

S82

33

S83

34

S84

35

S85

36

S86

37

S87

38

S88 39S89 40S90 41S91 42S92 43S93 44S94 45S95 46S96 47S48 48S47 49S46 50S45 51S44 52S43 53S42 54S41 55S40 56

S39

57S3

858

S37

59S3

660

S35

61S3

462

S33

63S3

264

S31

65S3

066

S29

67S2

868

S27

69S2

670

S25

71S2

472

S23

73S2

274

S21

75S2

076

S19

77S1

878

S17

79S1

680

S15

81S1

482

S13

83S1

284

S11

85S1

086

S987

S888

S789

S690

S591

S492

S393

S294

S195

V096

V297

V398

VSS99

VDD100

CL1101

SHL1102

SHL2103

CL2104

DL1105

DR1106

DL2107

DR2108

M109

S49110

U2

ST7921

C81

C72

C63

C54

C45

C36

C27

C18

S19

S210

S311

S412

S513

S614

S715

S816

S917

S10

18S1

119

S12

20S1

321

S14

22S1

523

S16

24S1

725

S18

26S1

927

S20

28

S41

29S4

230

S43

31S4

432

S45

33S4

634

S47

35S4

836

S49

37S5

038

S51

39S5

240

S53

41S5

442

S55

43S5

644

S57

45S5

846

S59

47S6

048

S81

49S8

250

S83

51S8

452

S85

53S8

654

S87

55S8

856

S89

57S9

058

S91

59S9

260

S93

61S9

462

S95

63S9

664

S97

65S9

866

S99

67S1

0068

S121

69S1

2270

S123

71S1

2472

S125

73S1

2674

S127

75S1

2876

S129

77S1

3078

S131

79S1

3280

S133

81S1

3482

S135

83S1

3684

S137

85S1

3886

S139

87S1

4088

C17

89C1

890

C19

91C2

092

C21

93C2

294

C23

95C2

496

C997

C10

98C1

199

C12

100

C13

101

C14

102

C15

103

C16

104

S21

105

S22

106

S23

107

S24

108

S25

109

S26

110

S27

111

S28

112

S29

113

S30

114

S31

115

S32

116

S33

117

S34

118

S35

119

S36

120

S37

121

S38

122

S39

123

S40

124

S61

125

S62

126

S63

127

S64

128

S65

129

S66

130

S67

131

S68

132

S69

133

S70

134

S71

135

S72

136

S73

137

S74

138

S75

139

S76

140

S77

141

S78

142

S79

143

S80

144

S101

145

S102

146

S103

147

S104

148

S105

149

S106

150

S107

151

S108

152

S109

153

S110

154

S111

155

S112

156

S113

157

S114

158

S115

159

S116

160

S117

161

S118

162

S119

163

S120

164

S141

165

S142

166

S143

167

S144

168

S145

169

S146

170

S147

171

S148

172

S149

173

S150

174

S151

175

S152

176

S153

177

S154

178

S155

179

S156

180

S157

181

S158

182

S159

183

S160

184

C32

185

C31

186

C30

187

C29

188

C28

189

C27

190

C26

191

C25

192

L1WDG1603P

C1104

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

JP1HEADER 16

12

JACON2

12

JKCON2

123

J1

CON3

R14.7K

R24.7K

R32.2K

R44.7K

R54.7K

R6

33K

R7

2K

R9

33R8

33

VCC

VCC

VCC

VCC

12

JP2HEADER 2

VCC

VCC

C1 C2 C3 C4 C5 C6 C7 C8 C9 C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

C29

C30C31C32

S39S40S41S42S43S44S45S46S47S48S49S50S51S52S53S54S55S56S57S58S59S60S61S62S63S64

S1 S2 S3 S4 S5 S6 S7 S8 S9 S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S31

S32

S33

S34

S35

S36

S37

S38

S65

S66

S67

S68

S69

S70

S71

S72

S73

S74

S75

S76

S77

S78

S79

S80

S81

S82

S83

S84

S85

S86

S87

S88

S89

S90

S91

S92

S93

S94

S95

S96

S97

S98

S99

S100

S101

S102

S103

S104S105S106S107S108S109S110S111S112

S113

S114

S115

S116

S117

S118

S119

S120

S121

S122

S123

S124

S125

S126

S127

S128

S129

S130

S131

S132

S133

S134

S135

S136

S137

S138

S139

S140

S141

S142

S143

S144

S145

S146

S147

S148

S149

S150

S151

S152S153S154S155S156S157S158S159S160

C25

C26

C27

C28

C29

C30

C31

C32

C1 C2 C3 C4 C5 C6 C7 C8C9C1

0C1

1C1

2C1

3C1

4C1

5C1

6

C17

C18

C19

C20

C21

C22

C23

C24

S1S2S3S4S5S6S7S8S9S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S31

S32

S33

S34

S35

S36

S37

S38

S39

S40

S41

S42

S43

S44

S45

S46

S47

S48

S49

S50

S51

S52

S53

S54

S55

S56

S57

S58

S59

S60

S61

S62

S63

S64

S65

S66

S67

S68

S69

S70

S71

S72

S73

S74

S75

S76

S77

S78

S79

S80

S81

S82

S83

S84

S85

S86

S87

S88

S89

S90

S91

S92

S93

S94

S95

S96

S97

S98

S99

S100

S101

S102

S103

S104

S105

S106

S107

S108

S109

S110

S111

S112

S113

S114

S115

S116

S117

S118

S119

S120

S121

S122

S123

S124

S125

S126

S127

S128

S129

S130

S131

S132

S133

S134

S135

S136

S137

S138

S139

S140

S141

S142

S143

S144

S145

S146

S147

S148

S149

S150

S151

S152

S153

S154

S155

S156

S157

S158

S159

S160

Paul Yung1 1

1.2SitronixST7920 LCM

R1010K

CLK TT1 TT2

ST7920

V4.0 47/49 2008/08/18

Application circuit 2: LCD : 32-COM x 160-SEG LCD Voltage : VCC x 2 (Voltage doubler is used). *VLCD (V0), VOUT and VCAP3M should not over 7V.

1 2 3 4 5 6

A

B

C

D

654321

D

C

B

A

Title

Number RevisionSize

B

Date: 17-Aug-2001 Sheet of File: D:\adom\Documents\sch\7920_B~13.DDB Drawn By:

V01

V12

V23

VXA4

VXB5

VXC6

V37

V48

VSS9

VDD10

XRESET11

CL112

CL213

VDD14

M15

DOUT16

RS17

RW18

E19

VSS20

OSC121

OSC222

PSB23

D024

D125

D226

D327

D428

D529

D630

D7

31

XO

FF32

VO

UT

33

CAP3

M34

CAP1

P35

CAP1

M36

CAP2

P37

CAP2

M38

VD

239

C140

C241

C342

C443

C544

C645

C746

C847

C948

C10

49

C11

50

C12

51

C13

52

C14

53

C15

54

C16

55

C17

56

C18

57

C19

58

C20

59

C21

60

C22

61

C23

62

C24

63

C25

64

C26

65

C27

66

C28

67

C29

68

C30 69C31 70C32 71C33 72S64 73S63 74S62 75S61 76S60 77S59 78S58 79S57 80S56 81S55 82S54 83S53 84S52 85S51 86S50 87S49 88S48 89S47 90S46 91S45 92S44 93S43 94S42 95S41 96S40 97S39 98

S38

99S3

710

0S3

610

1S3

510

2S3

410

3S3

310

4S3

210

5S3

110

6S3

010

7S2

910

8S2

810

9S2

711

0S2

611

1S2

511

2S2

411

3S2

311

4S2

211

5S2

111

6S2

011

7S1

911

8S1

811

9S1

712

0S1

612

1S1

512

2S1

412

3S1

312

4S1

212

5S1

112

6S1

012

7S9

128

S812

9S7

130

S613

1S5

132

S413

3S3

134

S213

5S1

136

U1

ST7920

S50

1

S51

2

S52

3

S53

4

S54

5

S55

6

S56

7

S57

8

S58

9

S59

10

S60

11

S61

12

S62

13

S63

14

S64

15S6

516

S66

17

S67

18

S68

19

S69

20

S70

21

S71

22

S72

23

S73

24

S74

25

S75

26

S76

27

S77

28

S78

29

S79

30

S80

31

S81

32

S82

33

S83

34

S84

35

S85

36

S86

37

S87

38

S88 39S89 40S90 41S91 42S92 43S93 44S94 45S95 46S96 47S48 48S47 49S46 50S45 51S44 52S43 53S42 54S41 55S40 56

S39

57S3

858

S37

59S3

660

S35

61S3

462

S33

63S3

264

S31

65S3

066

S29

67S2

868

S27

69S2

670

S25

71S2

472

S23

73S2

274

S21

75S2

076

S19

77S1

878

S17

79S1

680

S15

81S1

482

S13

83S1

284

S11

85S1

086

S987

S888

S789

S690

S591

S492

S393

S294

S195

V096

V297

V398

VSS99

VDD100

CL1101

SHL1102

SHL2103

CL2104

DL1105

DR1106

DL2107

DR2108

M109

S49110

U2

ST7921

C81

C72

C63

C54

C45

C36

C27

C18

S19

S210

S311

S412

S513

S614

S715

S816

S917

S10

18S1

119

S12

20S1

321

S14

22S1

523

S16

24S1

725

S18

26S1

927

S20

28

S41

29S4

230

S43

31S4

432

S45

33S4

634

S47

35S4

836

S49

37S5

038

S51

39S5

240

S53

41S5

442

S55

43S5

644

S57

45S5

846

S59

47S6

048

S81

49S8

250

S83

51S8

452

S85

53S8

654

S87

55S8

856

S89

57S9

058

S91

59S9

260

S93

61S9

462

S95

63S9

664

S97

65S9

866

S99

67S1

0068

S121

69S1

2270

S123

71S1

2472

S125

73S1

2674

S127

75S1

2876

S129

77S1

3078

S131

79S1

3280

S133

81S1

3482

S135

83S1

3684

S137

85S1

3886

S139

87S1

4088

C17

89C1

890

C19

91C2

092

C21

93C2

294

C23

95C2

496

C997

C10

98C1

199

C12

100

C13

101

C14

102

C15

103

C16

104

S21

105

S22

106

S23

107

S24

108

S25

109

S26

110

S27

111

S28

112

S29

113

S30

114

S31

115

S32

116

S33

117

S34

118

S35

119

S36

120

S37

121

S38

122

S39

123

S40

124

S61

125

S62

126

S63

127

S64

128

S65

129

S66

130

S67

131

S68

132

S69

133

S70

134

S71

135

S72

136

S73

137

S74

138

S75

139

S76

140

S77

141

S78

142

S79

143

S80

144

S101

145

S102

146

S103

147

S104

148

S105

149

S106

150

S107

151

S108

152

S109

153

S110

154

S111

155

S112

156

S113

157

S114

158

S115

159

S116

160

S117

161

S118

162

S119

163

S120

164

S141

165

S142

166

S143

167

S144

168

S145

169

S146

170

S147

171

S148

172

S149

173

S150

174

S151

175

S152

176

S153

177

S154

178

S155

179

S156

180

S157

181

S158

182

S159

183

S160

184

C32

185

C31

186

C30

187

C29

188

C28

189

C27

190

C26

191

C25

192

L1WDG1603P

+ C34.7u

+

C2

4.7u

C1104

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

JP1HEADER 16

12

JACON2

12

JKCON2

123

J1

CON3

R14.7K

R24.7K

R32.2K

R44.7K

R54.7K

R6

33K

R7

2K

R9

33R8

33

VCC

VCC

VCC

12

JP2HEADER 2

VCC

VCC

C1 C2 C3 C4 C5 C6 C7 C8 C9 C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

C29

C30C31C32

S39S40S41S42S43S44S45S46S47S48S49S50S51S52S53S54S55S56S57S58S59S60S61S62S63S64

S1 S2 S3 S4 S5 S6 S7 S8 S9 S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S31

S32

S33

S34

S35

S36

S37

S38

S65

S66

S67

S68

S69

S70

S71

S72

S73

S74

S75

S76

S77

S78

S79

S80

S81

S82

S83

S84

S85

S86

S87

S88

S89

S90

S91

S92

S93

S94

S95

S96

S97

S98

S99

S100

S101

S102

S103

S104S105S106S107S108S109S110S111S112

S113

S114

S115

S116

S117

S118

S119

S120

S121

S122

S123

S124

S125

S126

S127

S128

S129

S130

S131

S132

S133

S134

S135

S136

S137

S138

S139

S140

S141

S142

S143

S144

S145

S146

S147

S148

S149

S150

S151

S152S153S154S155S156S157S158S159S160

C25

C26

C27

C28

C29

C30

C31

C32

C1 C2 C3 C4 C5 C6 C7 C8C9C1

0C1

1C1

2C1

3C1

4C1

5C1

6

C17

C18

C19

C20

C21

C22

C23

C24

S1S2S3S4S5S6S7S8S9S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S31

S32

S33

S34

S35

S36

S37

S38

S39

S40

S41

S42

S43

S44

S45

S46

S47

S48

S49

S50

S51

S52

S53

S54

S55

S56

S57

S58

S59

S60

S61

S62

S63

S64

S65

S66

S67

S68

S69

S70

S71

S72

S73

S74

S75

S76

S77

S78

S79

S80

S81

S82

S83

S84

S85

S86

S87

S88

S89

S90

S91

S92

S93

S94

S95

S96

S97

S98

S99

S100

S101

S102

S103

S104

S105

S106

S107

S108

S109

S110

S111

S112

S113

S114

S115

S116

S117

S118

S119

S120

S121

S122

S123

S124

S125

S126

S127

S128

S129

S130

S131

S132

S133

S134

S135

S136

S137

S138

S139

S140

S141

S142

S143

S144

S145

S146

S147

S148

S149

S150

S151

S152

S153

S154

S155

S156

S157

S158

S159

S160

Paul Yang1 1

1.4Sitronix

ST7920 LCM (Booster)

R1010K

CLK TT1 TT2

ST7920

V4.0 48/49 2008/08/18

ST

7920

Dot M

atrix LC

D P

anel

VSS

Vcc(+

5V/+

3V)

DB

0-DB

7

To M

PU

V4

V3

V2

V1

V0 M

CL

1

CL

2

VSS

VD

D

Seg 1-64

Com

1-32

Note:R

egsister=2.2K

~10K

ohm

VR

=1K

~30K

ohm

ST

7921

V2

V3

V0

VSS

SH

L2

SH

L1

VD

D

DL

1

M

CL

2

CL

1

DR

1

DL

2

DR

2Seg 1-96

ST

7921

V2

V3

V0

VSS

SH

L2

SH

L1

VD

D

DL

1

M

CL

2

CL

1

DR

1

DL

2

DR

2Seg 1-96

Regsister

Regsister

Regsister

Regsister

Regsister

VR

Dout

Application circuit 3: LCD : 2Line 16Chinese Word (32-COM x 256-SEG)

ST7920

V4.0 49/49 2008/08/18

Application circuit for testing CGROM and HCGROM:

R1

R2

R2

R2