sir-pmk1 professional motorcycle install kitthe sir-pmk1 is compatible with all sirius branded plug...

SIR-PMK1Professional Motorcycle Install Kit

Installation Guide

Desktop Docking Station

© Directed Electronics, all rights reserved.�

Professional Motorcycle Install Kit

Table of ContentsFCC Notice 4Warning and Safety information 5Congratulations 6Package contents 7Important pre-installation notes 8Choosing an apppropriate mounting location 9Mounting bracket 10Wiring and wire connections 12Connecting the SIRIUS radio to the motorcycle sound system 14Final connections and testing 16Using the moisture guard 17Warranty 19


FCC NOTICE:

This device complies with Part 15 of FCC rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

Directed Electronics is not responsible for any radio or TV interference caused by unauthorized modifica-tions to this equipment. Such modifications could void the User’s authority to operate the equipment.




Warning and Safety InformationSafety Precautions

Be sure to observe the following warning. Failure to follow these safety instructions and warnings may result in a serious accident and/or personal injury.

• Installation must be performed according to this installation guide. Directed Electronics is not responsible for issues arising from installations not performed according to the procedures in this guide.

• Do not install the dual voltage adapter where it will be exposed to high levels of humidity, moisture, or dust.• To avoid short circuits or damage, do not open the adapter.• If the adapter emits smoke or unusual odors, disconnect power immediately.• Do not drop the unit modules or subject them to strong shocks.• The installation and use suggestions contained in this manual are subject to any restrictions or limitations that may

be imposed by applicable law. The purchaser should check applicable law for any restrictions or limitations before installing and/or operating this unit.


Congratulations

Congratulations on the Purchase of your new SIR-PMK1 Professional Motorcycle Install Kit!

The SIR-PMK1 is compatible with all SIRIUS Branded Plug and Play or portable radios. It may also be compatible with other Sirius radios, consult your authorized Sirius dealer for specific compatibility questions

For the latest information about this and other SIRIUS products and accessories, visit http://www.directedsirius.com.




Package Contents

1 Sirius Universal Cradle1 Dual voltage power supply, 5/12 volts (with ground wire and ring terminal connected)1 ATC fuse holder with 2 Amp fuse1 Cradle Mounting Bracket with Swivel2 Moisture Guards (sized to fit SP3/4, ST3/4 and Stratus)1 Antenna 1 3.5mm stereo audio cable1 5V harness with 2-pin connector1 12V harness with 3-pin connector1 Handle Bar Clamp

Audio Cable

Swivel Base on universal

Mounting Bracket

Assembly of Swivel Base to Mounting Bracket

Dual Voltage Power Adapter

FM Direct Audio Relay Dual Voltage Power Supply Cables

2 pin 5v

3 pin 12v

Audio Cable


Mounting Bracket



FM Direct Audio Relay Dual Voltage Power Supply Cables

2 pin 5v

3 pin 12v

Audio Cable


Mounting Bracket



FM Direct Audio RelayDual Voltage Power Supply Cables

2 pin 5v

3 pin 12v

1 90 degree metal Antenna Bracket1 Straight metal Antenna Bracket6 6 inch zip/wire ties1 Hardware kit:

6 Ring Washers 2, ¾ inch Spacers 2, SHCS (Stainless, Hexhead, Cap Screws) M6X1.00x35 2, SHCS (Stainless, Hexhead, Cap Screws) ¼-20x1.502 SHCS (Stainless, Hexhead, Cap Screws) ¼-20x1.751 Sirius Magnet Mount Antenna with 6” cable and SMB connector

<COMPANY NAM

E>

SCALE:1:2

SIZEDW

G. NO.

AREV.

MATERIAL

FINISH

----

DO NOT SCALE DRAWING

APPLICATION USED ONNEXT ASSY

DIMENSIONS ARE IN INCHES

TOLERANCES:FRACTIONAL

±ANGULAR: M

ACH±

BEND ±

TWO PLACE DECIM

AL ±

THREE PLACE DECIMAL

±

NAME

DATE

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

SHEET 1 OF 1W

EIGHT:

COMM

ENTS:

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAM

E HERE>. ANY REPRODUCTION IN PART OR AS A W

HOLEW

ITHOUT THE WRITTEN PERM

ISSION OF<INSERT COM

PANY NAME HERE> IS

PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Moisture GuardBracketsHandle bar clamp

Antenna

Swivel base

Audio Cable

<COMPANY NAME>

SCALE:1:2

SIZE DWG. NO.

AREV.

MATERIAL

FINISH

--

--

DO NOT SCALE DRAWINGAPPLICATION

USED ONNEXT ASSY

DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONAL ±ANGULAR: MACH ± BEND ±TWO PLACE DECIMAL ±THREE PLACE DECIMAL ±

NAME DATE

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

SHEET 1 OF 1WEIGHT:

COMMENTS:

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OF<INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF<INSERT COMPANY NAME HERE> IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Cradle


IMPORTANT PRE-INSTALLATION NOTESDirected Electronics recommends that you have this prod-uct professionally installed.Read this entire installation manual as well as the owner's guide provide with your Sirius radio before proceeding with the installation.

If the installation notes in this manual are not followed, it may result in personal injury or damage to the various components of the Sirius radio, damage to the motorcycle’s audio system, damage to the motorcycle’s electrical sys-tem, or damage to the motorcycle’s mechanical system.

Familiarize yourself with any existing audio system on the motorcycle by consulting the owner’s manuals for these systems before making any wire or cable connections to those systems.

The Dual Voltage Power Adapter is designed for 12 volt DC negative ground motorcycle electrical systems only.When faced with a blown fuse, always determine the cause and correct the problem before replacing the fuse and be sure to use a replacement fuse of the same type, rating and amperage.

Do not cut any of the wires and cables included with the Professional Motorcycle Install Kit or the Sirius radio being

installed. Any excess cable or wire length should be neatly bundled or coiled, and secured in

Do not route wires or cables across sharp edges, or through holes which could result in the wire or cable be-coming damaged, chafed, cut, or shorted. If routing across sharp edges is unavoidable, use the provided Expandable sleeve to protect the wires. Use rubber grommets when routing through holes. Make sure to route all wires away from any moving parts that may damage them.Avoid pinching, squashing, kinking, or crimping any of the wires used in this install or any of the motorcycle’s existing wires/cables during the installation.

Refer to the owner's guide for your Sirius radio to deter-mine the voltage required in order to select correct plug to be used for the output of the Dual Voltage Power Adapter. The plugs provided with thise installation kit are designed to only fit Sirius-branded radios that operate on either 5V or 12V DC. They are keyed and sized to prevent inadvertent connection to radios of incorrect voltage rating. Do not force the coaxial output connector into the cradle of your Sirius radio. If the connector does not appear to fit, stop and make sure you have selected the correct output har-ness to match your radio's voltage rating.




SIRIUS RADIO VOLTAGE GUIDE.

It is very important to choose a mounting location that does not interfere with the operator’s view of the road, gauges, rearview mirrors or steering of the motorcycle. The most common and intended location is somewhere on the Motor-cycle’s handle bars. Some Motorcycles utilize clutch and brake handle mounting clamps that are compatible with the threads on the supplied Stainless Hexhead Cap Screws. In some cases the factory screws can be used to attach the Cradle Mounting Bracket and Metal Antenna Bracket. In other cases you may find that the factory screws are too short and will have to select the appropriate length Stain-less Hexhead Cap Screws to replace the factory screws to accommodate the added thickness of the Swivel Base and Metal Antenna Bracket combination.

MODEL P/N VOLTAGE

Sportster SPR1, SPR1A 12V

Sportster replay SPR2 12V

Starmate ST1 12V

Starmate replay ST2 12V

Sirius One SV1 12V

Stiletto 10/100 SL10PK1, SL100PK1 5V

S50 S50TK1 5V

Sportster 3/4 SP3, SP4 5V

Starmate 3/4 ST3, ST4 5V

Stratus SV3TK1 5V

InV SV2TK1 5V

CHOOSING AN APPROPRIATE MOUNT-ING LOCATION.

© Directed Electronics, all rights reserved.10

MOUNTING BRACKET. On Motorcycles that do not have a matching bolt pattern for the clutch and brake handle clamps, you will have to use the included Handle Bar Clamp to attach the Cradle Mounting Bracket and Metal Antenna Bracket assembly. When attaching the Cradle Mounting Bracket directly to the clutch or brake clamps be sure to re-tighten the clutch or brake handle clamp so that the handles are oriented the way they were originally and tight enough that they do not move. (See sample pictures/illustrations of mounting options and orientations of Cradle Mounting Bracket and Metal Antenna Bracket).

On some motorcycles you may use the straight antenna bracket bolted to a different part of the motorcycle.

At this point the Sirius Universal Cradle can be attached with the supplied screws. In some cases it may be neces-sary to attach the Sirius Universal Cradle to the Cradle Mounting Bracket while the clamp is loose to accommo-date access to the screws with a screw driver. Once the Sirius Universal Cradle is attached, plug in the Sirius Plug and Play Tuner to assure that its location is appropriate and does not interfere with the proper operation of the Motorcycle.

At this point the Sirius Magnet Mount Antenna can be fitted to the Metal Antenna Bracket. The Antenna plug can also be plugged into the cradle at this time.




Example 1 Bracket (shown here with cradle and antenna also attached) mounted to Clutch handle clamp

Example 2 Bracket (shown here with cradle and antenna also attached) mounted to handle bar using handle bar clamp.


WIRING AND WIRE CONNECTIONS.Refer to your Sirius Plug and Play Tuner guide to deter-mine whether the Tuner is a 12 volt or 5 volt unit. This will dictate which Coaxial Power cable you will need to use with the Dual Voltage Power Supply. The three pin plug is for 12 volt units and the two pin plug is for 5 volt units. The plugs are not interchangeable making it virtually impossible to use the wrong one.

After determining the correct harness and plug you should decide on a mounting location for the Power Supply. It is important that the Power Supply not be exposed to the ele-ments, especially rain! Mounting it securely under the seat is usually a good choice.

Once an appropriate mounting location has been chosen you can begin to wire the Power Supply to the Motorcycle’s electrical system. The black ground wire should be con-nected first. It is recommended that it be attached securely to the battery’s negative terminal. If the ground wire is too short to reach the battery it will be necessary to cut the ring terminal off, sufficiently extend the wire and crimp on a new ring terminal. If, for some reason the battery is not an option, a factory ground can be used but the battery is always your best bet. It is not recommended to ever drill a hole in the frame of the motorcycle.

Next, you should attach the supplied fuse holder to a switched, positive 12 volt source. An accessory circuit is preferred and can be identified as a wire that shows posi-tive 12 volts when the ignition is on and drops to 0 volts when the starter is cranking and then returns to positive 12 volts once the motorcycle is running. If an acces-sory circuit is not available or convenient then an ignition source can be used. It will test the same as an accessory circuit but the voltage will stay at positive 12 volts while the starter is cranking.

The other end of the fuse holder can be attached to the red lead of the Power Supply using the supplied butt connec-tor. Make sure that the fuse is out of the fuse holder while making this connection and during the remainder of the installation. Wait until the installation is complete before installing the fuse.

It is not recommended to use a constant source of voltage. Doing so will run the risk of draining the battery by acci-dentally leaving the Sirius tuner on while the motorcycle is not running. This could dramatically shorten the battery’s life and cause it to not take a full charge anymore.


© Directed Electronics, all rights reserved.1�


DC5VANT FMAUDIO

Cradle Rear view

To Power Source

+

-


CONNECTING THE SIRIUS RADIO TO THE MOTORCYCLE’S SOUND SYSTEM.There are three different ways to connect the Sirius Tuner to a Motorcycle’s Sound System. The method of connection will depend on the brand of Motorcycle and the particular sound system installed on it.

Many Motorcycle Sound Systems do not have an auxil-iary input. Therefore it is necessary in these cases to FM modulate the Sirius audio to the Sound System. One option is to use the wireless FM modulator built into the Sirius Tuner by following the instructions for the wireless modu-lator contained in the tuner’s operation guide.

In some cases the wireless signal will not be strong enough to overcome interference from local FM stations. In this case it is recommended to use the optional FM Direct Audio relay (Part #: FMDA25). this relay will install between the motorcycle's radio and the FM antenna. Refer to FMDA25 install guide for details.

Some Motorcycle radios have an auxiliary input in the form of a 3.5mm stereo input jack. These auxiliary inputs can be connected to the Sirius Tuner Cradle by using the supplied 3.5mm stereo cord. One end plugged into the radio auxil-iary input and the other into the line out of the Sirius Tuner Cradle. Listening to the Sirius Tuner would then be accom-plished by simply selecting the radio’s auxiliary input.

You may also be able to connect your Sirius radio directly to a helmet earphone system. The output voltage of Sirius radios can drive some high efficiency earbuds without an external amplifier.




Wiring Diagram:

CRADLE REAR VIEW

To Motorcycle Audio system

Auxiliary Input Jacks L/R

Antenna

Power Supply

To Power Source


FINAL CONNECTIONS AND TESTING.Before preceding double check all connections and mount-ing points assuring that they are all secure and tight.

At this point install the fuse into the fuse holder and seat the Sirius radio into the cradle. Turn the Motorcycle’s igni-tion on and turn the Sirius radio on. If the Tuner has never been activated before be sure to let it update the chan-nels as described in the radio’s operation manual. Once the channels have updated follow the operation guide’s instructions to select the desired FM frequency you wish to use if you are using one of the FM Modulating techniques described previously and verify that it is working with no distortion or interference. If you are using an available auxiliary input to the radio simply select the auxiliary source on the radio and verify that it is playing the Sirius Weather Channel (184). You can now contact Sirius to have your radio activated and start enjoying all of the channels Sirius has to offer.

At this point you can make final adjustments to the Swivel or Cradle Mounting Bracket if necessary and replace any parts of the Motorcycle that may have been removed to ac-commodate the installation such as the seat.

Make sure to use one of the supplied Moisture Guards whenever the Motorcycle is being operated in inclement weather to protect the Sirius radio. You should always remove the radio and store it in a safe dry location when not in use. The Sirius Universal Cradle is not designed for exposure to moisture and should always be kept covered with the moisture Guard or removed when not in use.




Using the Moisture Guard

Since the moisture guard is an extremely snug fit please follow these instructions to avoid difficulty when removing the moisture guard from your Sirius radio.

1 Unfasten the moisture guard's velcro flaps from beneath cradle (make sure all flaps are exposed to prevent them from inadvertently getting caught during removal).

2 In this step remove the Sirius radio along with moisture guard from cradle first before attempting to remove moisture guard from radio. Using thumb and fingers grasp the moisture guard and radio firmly on both sides (do not grasp front and back as damage to the display may result). Pull system vertically from cradle until clear (Fig A).

3 Now with your Sirius radio detached from cradle the moisture guard can be removed from the radio (Fig B).

Caution: On some radios (SP4 model, used in this exam-ple) there is a button control that protrudes through an opening in the front of the moisture guard. When removing guard from this radio, slide finger under moisture guard and lift until this area of the moisture guard clears this control. Once cleared and free from contraint, slowly work radio out of guard.

Fig A


Copyrights & Trademarks

2006 SIRIUS Satellite Radio Inc. All Rights Reserved

“SIRIUS”, the SIRIUS dog logo, channel names and logos are trademarks of

SIRIUS Satellite Radio Inc. All Rights Reserved

Fig B

lift guard here

opening




Limited One Year Consumer Warranty

Directed Electronics (herein “DIRECTED”) promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of one-year from the date of purchase from the dealer as indicated by the date code marking of the product. During this one-year period, there will be no charge for this replace-ment PROVIDED the unit is returned to DIRECTED, shipping pre-paid. This warranty is non-transferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose, and does not cover damage to the unit caused by installation or removal of the unit. This warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper service or other causes not arising out of defects in materials or construction. ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANT-ABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AU-THORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. IN NO EVENT WILL DIRECTED BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFITS) AND IN NO EVENT, SHALL DIRECTED’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Unit must be returned to DIRECTED, postage prepaid, with bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number, and address, authorized dealer’s name and address, and product description. Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF PURCHASE FROM AN AUTHORIZED DIRECTED DEALER. BY PURCHASING THIS PRODUCT, THE CON-SUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

sir-pmk1 professional motorcycle install kitthe sir-pmk1 is compatible with all sirius branded plug...

Documents